Yealink VC800 v3 Quick Start Guide PDF

Yealink VC800 Full HD Video Conferencing System Quick Start Guide Applies to firmware version 63.30.0.6 or laterV30.8

Yealink Network Technology CO., LTD

1.8m HDMI Cable2 (for the display device)

VCH50 Video Conferencing Hub

3m Ethernet Cable

AAA Batteries2

A Package

VC800 Quick Start Guide

1.2m Mini DP Cable

7.5m Ethernet Cable

0.5m Ethernet Cable

Mounting Bracket and Accessories

1.2m HDMI Cable (for content sharing)

CP960 Conference Phone

Packaging Contents

VC800 Codec

+ +

+ 2 2

2

0.3m Micro USB Cable

Charger Cradle

B Package

We recommend that you use the accessories provided or approved by Yealink. The use of unapproved third-party accessories may

result in reduced performance.

VC800 codec can work with A package or B package.

The VC800 system should be used with Yealink original power adapter (48V/0.7A) only. The use of the third-party power adapter may

cause the damage to the system. The cable and wire should be replaced at once if its skin is broken.

CPW90 Quick Start Guide

CPW90 Wireless Expansion Mic2

VCR11 Remote Control

OK

CP960 Conference Phone

CPE90 Wired Expansion Mic2

Cable Ties5 Power Adapter Velcro2

VESA Accessory

Before using the HDMI cable, put the magnet rings on it to prevent electromagnetic interference.

(One Velcro is on the bracket)

1

Steps

1

32

4

VC800 Codec Installation

3

Open the baffle.

Push the bracket along the track of the V800 codec.

Remove one Velcro.

Put the bracket on the top of the TV.

Stick a Velcro onto the back of the TV, and make sure that the bracket and the back of the TV are tightly positioned against each

other.

TV5

4

5

Notice the direction of the bracket

Mount on top of a TV Please choose the following installation method when the thickness of the TV is between 16mm and 55mm.

Select one of the following installation method based on your site requirements:

a. Put on a Flat Surface b. Mount on top of a TV c. Mount on a wall d. Mount on a ceiling e. Mount onto a TV stand or a tripod

Put on a Flat Surface You can put the VC800 codec on a conference room table, and make sure that the slope is not more than 5 degrees so that the VC800

can operate correctly.

Please choose the following installation method when the thickness of the TV is between 50mm and 100 mm.

TV

5

6

4

3

2

1

2

3

1

Notice the direction of the bracket

If your VC800 codec cannot be mounted on the top of a TV when the bracket has reached the given location, remove the bracket, and then convert its direction. Refer to the following section for more information.

2

Steps

1

32

4

3

Open the baffle.

Push the bracket along the track of the VC800 codec.

Stick a Velcro onto the bracket.

Remove one Velcro.

Put the bracket on the top of the TV.

Stick a Velcro onto the back of the TV, and make sure that the bracket and the back of the TV are tightly positioned against

each other.

5

6

Do not pick up the bracket which connects with a VC800 codec, the VC800 codec may fall down in this situation.

48mm

Hole diameter: 6mm

Hole depth: 30mm

Screw specification: T430

Mount on a Wall

21

The recommended height for VC800 codec positioning is 1.5m-1.8m above the ground.

X

If your VC800 codec cannot be mounted on the top of a TV when the bracket has reached the given location, you should choose other installation methods. The VC800 codec may fall down when the thickness of the TV is more than 100 mm. In this situation, do not mount the VC800 on the top of a TV.

3

Steps

1

2

3

4

Punch holes into the wall and then insert the expansion bolts.

Secure the bracket using the T430 screws.

Push the VC800 codec along the track of the bracket.

Secure the VC800 codec onto the bracket using the M38 screws.

3

4

Screw specification: M38

Mount on a Ceiling

.

.

.

.

1 4.

0m m

0.

55 in

. 62

.5 m

m (2

.4 6i

n. )

Screw hole

6.0 mm(0.24 in.) in depth

Location hole

5.0 mm(0.20 in.) in diameter

4

If you choose the ceiling-mounted installation, you need to purchase a bracket separately. The bracket must meet the following

requirements:

Able to bear a weight of at least 10.5kg (23.15 lb.) and has a thickness between 2mm (0.08 in.) and 3 mm (0.12 in.).

Comes with a 1/4-20 UNC screw.

Comes with a location pillar, which can be inserted into the location hole of the VESA accessory.

The distance between the screw on the bracket and the location pillar must be 14 mm (0.55 in.).

5

1 2

Screw specification: M38

Remote Control and Cable Ties Installation

Install batteries

Fasten the cables with the cable tie

3 Screw specification: M38

1

2

3

Push the VESA accessory along the track of the VC800 codec.

Secure the VESA accessory to the VC800 codec using the M38 screws.

Align the location pillar at the location hole, and then secure the bracket to the VESA accessory using the 1/4-20 UNC screw.

TV Stand

Mount onto a TV Stand or a Tripod

You need to purchase a TV stand or a tripod separately. The TV stand or tripod has the same requirements as the backet used in the

ceiling-mounted installation method.

The installation steps are the same as the ceiling-mounted installation steps.

Steps

1 2

3

You can also connect the VC Hub/Phone port on the VC800 codec to the Internet port on CP960 conference phone directly.

Please connect to the HDMI 1 port if you only have one display device.

VCH50

Power Adapter

Display2

Connections

1.8m HDMI Cable

3m Ethernet Cable

0.5m Ethernet Cable 1.2m

Mini DP Cable 1.2m HDMI Cable

CP960

or

Power Adapter

Display2

1.8m HDMI Cable

7.5m Ethernet Cable

3m Ethernet Cable

0.5m Ethernet Cable

CP960

MINI DP HDMI

CodecAudio

PC

If you purchase A package, do the following:

If you purchase B package, do the following:

7.5m Ethernet Cable

VCH50

1.2m Mini DP Cable

1.2m HDMI Cable or

MINI DP HDMI

CodecAudio

PC

6

Network Deployment

VC800 supports two network deployment methods: Cloud deployment and traditional deployment. You can choose the deployment method

according to your need.

Cloud Deployment

Select More->Setting->Advanced (Default Admin Password:0000)->Video Conference Platform.

In the Cloud Account field, check the Enabled checkbox.

Select the desired platform from the pull-down list of Platform Type.

.

.

.

With Cloud service, organizations can communicate using the Cloud platform, so that complex network settings are unnecessary. You can log

into Yealink VC Cloud Management Service/Yealink Meeting Server/StarLeaf/Zoom/Pexip/BlueJeans/Mind platform using VC800 video

conferencing system. Get account information from your administrator.

Do the following to log into your VC800 via remote control:

Configure the desired platform and log in.

.

Head Office

If you deploy VC800 in the head office, at least one static public IP address is required in the head office to allow branch offices to

connect.

Option2: To deploy the VC800 in an Intranet (behind the firewall), you must assign a static private IP address to the VC800. In the

meantime, do port mapping on the firewall for VC800.

Traditional Deployment

Option1: To deploy the VC800 on a public network, at least one static public IP address is required, you need to assign a static public IP

address to the VC800.

Configure a Static IP

The following introduces how to configure a static IP address for the VC800.

Select More->Setting->Advanced (Default Admin Password:0000)->Internet Configuration.

Select IPv4 from the pull-down list of IP Mode.

Uncheck the DHCP checkbox.. . . . For example: use the remote control to configure a static IPv4 address to your VC800.

Press or to select IPv4, and then press .

Enter the IP address, subnet mask, gateway and DNS information in corresponding fields..

Press or to select Save, and then press to save the configuration.

The screen prompts [Reboot now?]. Select OK to reboot the system.

.

.

Do one of the following to deploy VC800:

If you do not log into the Cloud platform, you can choose traditional deployment method to deploy your VC800, and dial the IP address of

other device to make a call.

In order to ensure that the VC800 can work properly, please configure it according to the actual situation.

If it is in the head office, please make sure that it is reachable from public network. If it is in the branch office, please use intelligent traversal to

deploy it or just follow the same steps as for the head office.

7

It is recommended that you forward the web management port(443/TCP) to the public network, so that the head office can remotely

manage the branch office.

PortFunction

H.323 signal port

SIP optional

Audio & Video media stream port

Protocol Type

UDP/TCP

TCP/UDP

TCP/UDP

50000-50499

5060-5061

1719-1720

Video Resolution Recommended Bandwidth

Full HD 1080P 1.3Mb

People 1080P+Content 1080P 2.6Mb

Bandwidth Requirements To ensure the performance of video conference, the recommended bandwidth for VC800 is as below:

For more information of the configurations, contact your system administrator.

The bandwidth mentioned above is based on two-way conference. Bandwidth in head office should be increased along with the growing

number of connected branch offices .

Troubleshooting

After installation and deployment, you can test the VC800 by dialing the Yealink Demo Room. If you cant dial out successfully, please

contact your IT administrator to check the internal network configuration.

If you do not use Cloud platform and deploy your VC800 in an Intranet, you have configured port mapping on the firewall or gateway,

but you find that local system appears black screen and you cannot hear sound when you call Yealink Demo or other systems. The most

likely reason is that the firewall or gateway in your environment does not support the H.323 ALG feature. In this situation, please take the

following actions so that the NAT feature on the VC800 can solve this problem.

Select More->Setting->Advanced (Default Admin Password:0000)->NAT/Firewall.

Select Auto from the pull-down list of Type, the system will obtain public IP address automatically.

To configure NAT via the remote control:

.

.

Yealink Test Room IP: 117.28.251.50, 117.28.251.51

If the system does not obtain a public IP address automatically, select Manual Settings from thepull-down list of Type, and then

enter the public IP address in the Public IP Address field.

.

Configure Port Mapping

If the VC800 is deployed in an Intranet, and you want to solve the interconnection problem by port mapping, you must forward the

following ports to the public network on the firewall.

PortFunction

H.323 signal port

SIP optional

Audio & Video media stream port

Web management port optional

Protocol Type

UDP/TCP

5060

443

50000-50499

1719-1720

TCP/UDP

TCP/UDP

TCP

8

About Yealink

Yealink (Stock Code: 300628) is a global leading unified communication (UC) terminal solution provider that primarily offers video

conferencing systems and voice communication solutions. Founded in 2001, Yealink leverages its independent research and

development and innovation to pursue its core mission: Easy collaboration, high productivity. The companys high-quality UC terminal

solutions enhance the work efficiency and competitive advantages of its customers in over 100 countries. Yealink is the worlds

second-largest SIP phone provider and is number one in the China market.

Technical Support

Visit Yealink WIKI (http://support.yealink.com/) for the latest firmware, guides, FAQ, Product documents, and more. For better service, we

sincerely recommend you to use Yealink Ticketing system (https://ticket.yealink.com) to submit all your technical issues.

YEALINK(XIAMEN) NETWORK TECHNOLOGY CO.,LTD. Web: www.yealink.com | Addr: 309, 3th Floor, No.16, Yun Ding North Road, Huli District, Xiamen City, Fujian, P.R. China

Copyright2017YEALINK(XIAMEN) NETWORK TECHNOLOGY CO.,LTD. All rights reserved.

VC8 0 0 - EN