Contents

Yamaha DVR-S200 Theater System Owner's Manual PDF

1 of 115
1 of 115

Summary of Content for Yamaha DVR-S200 Theater System Owner's Manual PDF

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VSTRA FRLUNDA, SWEDEN YAMAHA MUSIC AUSTRALIA PTY, LTD. 17-33 MARKET ST., SOUTH MELBOURNE, 3205 VIC., AUSTRALIA

DVD HOME THEATER SOUND SYSTEM

DVX-S200 (DVR-S200+NX-S200+NX-C200+NX-SW200)

OWNERS MANUAL

U B

DVD/Super Audio CD RECEIVER

DVR-S200

2003 All rights reserved.

Printed in Malaysia WB85540

cv_DVX-S200_UB.p65 03.10.9, 3:26 PM1

Explanation of Graphical Symbols

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

IMPORTANT SAFETY INSTRUCTIONS 1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in accordance with the manufacturers instructions.

8 Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9 Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10 Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11 Only use attachments/accessories specified by the manufacturer.

12 Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13 Unplug this apparatus during lightning storms or when unused for long periods of time.

14 Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15 Be sure to allow spaces of at least 10 cm above, behind and on both sides of DVR-S200, and at least 20 cm above, behind and on both sides of NX-SW200.

16 Do not place the following objects on this unit: A vessel with water in it. If the vessel falls by vibrations and water spills, it may cause damage to the unit, and/or you may get an electric shock.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION

IMPORTANT Please record the serial number of this unit in the space below.

MODEL:

Serial No.:

The serial number is located on the rear or the bottom of this unit. Retain this Owners Manual in a safe place for future reference.

i

DVX-S200_UB.p65 03.10.20, 0:46 PM2

We Want You Listening For A Lifetime YAMAHA and the Electronic Industries Associations Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or distortion and, most importantly, without affecting your sensitive hearing.

Since hearing damage from loud sounds is often undetectable until it is too late, YAMAHA and the Electronic Industries Associations Consumer Electronics Group recommend you to avoid prolonged exposure from excessive volume levels.

1. IMPORTANT NOTICE : DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.

2. IMPORTANT : When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA.

3. NOTE : This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class B digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices.

This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices.

Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit OFF and ON, please try to eliminate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by the interference.

Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA 90620.

The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.

FCC INFORMATION (for US customers) E

n g

lish

ii

DVX-S200_UB.p65 03.10.20, 0:46 PM3

CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

The name plate is located on the bottom of the unit.

This product is a DVD home theater sound system consisting of the components shown on the table. Please check to make sure that all of the components listed in the table are included.

Model name Category No. of pcs

DVR-S200 DVD/Super Audio CD 1 RECEIVER

NX-S200 Satellite Speaker 4 (for front/surround)

NX-C200 Center speaker 1

NX-SW200 Subwoofer 1NX-SW200 Do not hold near the protrusions on the bottom of subwoofer. There protrusions are built to protect the woofer, but they can catch your finger and cause bodily injury.

iii

DVX-S200_UB.p65 03.10.20, 0:46 PM4

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

DVR-S200 This unit is not disconnected from the AC power source as long as it is connected to the wall outlet, even if this unit itself is turned off. This state is called the standby mode. In this state, this unit is designed to consume a very small quantity of power.

FOR CANADIAN CUSTOMERS To prevent electric shock, match wide blade of plug to wide slot and fully insert. This Class B digital apparatus complies with Canadian ICES- 003.

DANGER

When this unit is plugged to the wall outlet, do not place your eyes close to the opening of the disc tray and other openings to look into inside.

The laser component in this product is capable of emitting radiation exceeding the limit for Class 1.

DVR-S200 The name plate is located on the bottom of the unit.

WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

For U.K. customers If the socket outlets in the home are not suitable for the plug supplied with this appliance, it should be cut off and an appropriate 3 pin plug fitted. For details, refer to the instructions described below.

Note The plug severed from the mains lead must be destroyed, as a plug

with bared flexible cord is hazardous if engaged in a live socket outlet.

Special Instructions for U.K. Model

IMPORTANT THE WIRES IN MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL Brown: LIVE

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. Making sure that neither core is connected to the earth terminal of the three pin plug.

1 To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference.

2 Install this sound system in a well ventilated, cool, dry, clean place with at least 10 cm on the top, 10 cm on the left and right, and 10 cm at the back of DVR-S200, and 20 cm on the top, 20 cm on the left and right, and 20 cm at the back of NX-SW200 away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold.

3 Locate this unit away from other electrical appliances, motors, or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes from cold to hot, and do not locate this unit in a environment with high humidity (i.e. a room with a humidifier) to prevent condensation inside this unit, which may cause an electrical shock, fire, damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign object may fall onto this unit and/or this unit may be exposed to liquid dripping or splashing. On the top of this unit, do not place: Other components, as they may cause damage and/or

discoloration on the surface of this unit. Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury. Containers with liquid in them, as they may fall and liquid

may cause electrical shock to the user and/or damage to this unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain, etc. in order not to obstruct heat radiation. If the temperature inside this unit rises, it may cause fire, damage to this unit, and/or personal injury.

7 Do not plug in this unit to a wall outlet until all connections are complete.

8 Do not operate this unit upside-down. It may overheat, possibly causing damage.

9 Do not use force on switches, knobs and/or cords. 10 When disconnecting the power cord from the wall outlet, grasp

the plug; do not pull the cord. 11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth. 12 Only voltage specified on this unit must be used. Using this

unit with a higher voltage than specified is dangerous and may cause fire, damage to this unit, and/or personal injury. YAMAHA will not be held responsible for any damage resulting from use of this unit with a voltage other than specified.

13 To prevent damage by lightning, disconnect the power cord from the wall outlet during an electrical storm.

14 Do not attempt to modify or fix this unit. Contact qualified YAMAHA service personnel when any service is needed. The cabinet should never be opened for any reasons.

15 When not planning to use this unit for long periods of time (i.e. vacation), disconnect the AC power plug from the wall outlet.

16 Be sure to read the Solutions to Common Problems section on common operating errors before concluding that this unit is faulty.

17 Before moving this unit, press STANDBY/ON to set this unit in standby mode, and disconnect the AC power plug from the wall outlet.

18 Do not place much pressure against the Subwoofer port (front opening). The port or the unit may fall resulting in injury.

19 Do not place anything fragile beside the Subwoofer, as air pressure is produced that may break it, result in malfunction or cause injury.

20 Condensation will form when the surrounding temperature changes suddenly. Disconnect the power cord from the outlet, then leave the unit alone.

21 When using the unit for a long time, the unit may become warm. Turn the power off, then leave the unit alone for cooling.

E n

g lish

1

DVX-S200_UB.p65 03.10.20, 0:46 PM5

2

In a few steps, a whole new world of DVD will open up.

Settle into your favorite place on the sofa and let the show begin.

LETS GET THINGS READY! Page 6, Preparation Decide on a place for the speakers, perform a few simple connections, and thats all there is to it. Connecting Speakers and TV to CinemaStation couldnt be easier. Connecting the Speaker Cables with one touch colored connectors.

Come on, lets watch a DVD! Page 10, Basic Operations

Transform your room into a home theater in 3 steps.

Double and triple your enjoyment by CONNECTING OTHER EQUIPMENT. Page 46, Using Other Equipment Enhance the feeling of movement with DSP Programs when you play video games. Listen to and record CD-R and MiniDisc media. View and dub video media.

Connect Speakers and TV

Play a disc

Select a sound field

Sound fields to match the movie you are viewing and experience the feeling of being there.

Progressive scan technology for enjoying high-quality video even on a large screen.

001DVX-S200-en 04.3.1, 11:08 AM2

3

Enjoy playing A VARIETY OF DISCS! Page 28, Playing Video and Music Discs

In 3 short steps, play everything from commercial CDs to your own homemade discs.

Its time to TAKE YOUR LISTENING EXPERIENCE UP A NOTCH!

Page 54, Creating the Best Listening Space With the Speakers you can create a sound space to match the listening environment of the room. The Matrix 6.1 Decoder provides virtual surround back speakers for experiencing a remarkable

acoustic presence. SILENT CINEMA provides an incredible listening presence with headphones.

Lets listen to an FM/AM BROADCAST! Page 38, Listening to the Radio

In 2 quick steps you can enjoy live radio broadcasts.

Enjoy playing all types of discs including audio and video CDs, Super Audio CDs and MP3 music recorded on CD-Rs.

Create the sound and ambience to match the music you are listening to, whether it be the excitement of a nightclub or the acoustics of a concert hall.

In addition to Auto Tuning, you can use various controls including Auto Preset for FM channels.

Connect Speakers

Play a disc

Select a sound field

Connect Speakers and Antennas

Select a channel

E n

g lish

001DVX-S200-en 04.3.1, 11:08 AM3

4

CONTENTS

Basic

Advanced

Playing back a DVD

Advanced Features Names and Functions of Parts Page 18

Top and Front Page 18 CinemaStation Display Page 20

Remote Control Features Page 21 Amp Mode Button Names and Functions Page 22 DVD/CD Mode Button Names and Functions Page 23

Using the On Screen Menu Page 24

Selecting the Media Device Selecting the Equipment Page 26

Playing Video and Music Discs Playback Methods Page 28

Selecting a Scene or Tune Page 28 Customizing Playback Order (Program Play) Page 31 Repeating a Disc or Track (Repeat Play) Page 34 Using a Disc Menu Page 36 MP3 Playback Features Page 37 Playing a Super Audio CD Page 37

Preparation Introduction Page 6

About this Manual Page 6 Supplied Accessories Page 6 Preparing the Remote Control Page 7 Preparing the Speakers Page 7

Placing the Speakers Page 7 Connecting the Speakers and TV Page 8

Basic Operations Viewing a DVD Page 10 Useful Features Page 13

Selecting the Audio Language Page 13 Selecting the Subtitle Language Page 13 Moving Forward and Backward Page 13 Adjusting the Audio Volume Page 13 Pausing Playback Page 13 Switching the Viewing Angle Page 14 Restarting Playback from the Stop Position

(Memory Resume) Page 14 Enhancing the Sound Presence Page 15 Turning off the Sound Page 15 Controlling the DVDs Your Children Can View Page 15 Enhancing Video Quality Page 15 Answers to Common Problems Page 15

Sound Presence Finding the Best DSP Effect Page 16

001DVX-S200-en 04.3.1, 11:08 AM4

5

Listening to the Radio Connecting the Antennas Page 38

Connecting the FM Antenna Page 38 Connecting the AM Loop Antenna Page 38

Listening to the Radio Page 39 Selecting the Radio Tuner Page 39 Selecting Radio Stations Page 39 Setting Channels in Advance (Preset) Page 41 Selecting a Preset Station (Preset Tuning) Page 43 Changing the Order of Preset Stations Page 43 Receiving RDS Stations

(U.K. and Europe models only) Page 44

Using Other Equipment Connecting Video Equipment Page 46

Connecting a Game Console or VCR Page 46 Operating a VCR Page 48 Playing a Video Game or Operating

a Video Camera Page 48 Dubbing from a Video Camera to a VCR Page 49

Connecting Audio Equipment Page 50 Connecting a CD or MD Recorder Page 50 Playing a CD or MD Page 53 Recording Audio from CinemaStation Page 53

Creating the Best Listening Space Placing the Speakers (NX-P200) Page 54

Placing the Center Speaker Page 54 Placing the Subwoofer Page 54 Placing the Front and Surround Speakers Page 55 Using Commercially Available Speakers

or Cables Page 57 Adjusting the Speaker Volume Level Page 59

Adjusting the Speaker Balance with a Test Tone Page 59 Adjusting the Speaker Volume Level

During Playback Page 61 Setting the Speaker Size Page 63

Setting the Speaker Mode Page 63

More Information about DSP (Surround) Effects

Selecting DSP Program Effects Page 65 Using Matrix 6.1 Page 65 Using All Speakers for CD or Video Playback Page 67 Using Front Speakers Only for DSP Program

(Virtual Cinema DSP) Page 69 Using a DSP Program with Headphones

(SILENT CINEMA) Page 70 Using a DSP Program with Low Volume

(Night Listening) Page 71 Changing the Delay Time of a DSP Program Page 72 Reproducing the Original Dolby and DTS Sound Page 74 Reproducing Stereo Sound Page 75

Types of Input Signals Types of Input Signals Page 76

Checking Sound Information (Input Signal Information Display) Page 76

Switching Input Modes Page 78

Additional Features Using the Sleep Timer Page 79 Enjoying High-Quality Video

Progressive Scan (NTSC only) Page 80 Protecting Your Children

from Undesirable Material Page 81 Setting the Password and Parental

Control Level Page 81 Locking a Disc Page 83

Operating Other Equipment with the CinemaStation Remote Control

Storing Manufacturer Codes in the Remote Control Page 84 Setting the Manufacturer Code Page 84 Available Operations Page 85 Manufacturer Code List Page 87

Using the SET MENU Using the SET MENU Page 89

SET MENU List Page 89 Navigating the SET MENU Page 90

Using the On Screen Menu Using the On Screen Menu Page 93

Navigating the On Screen Menu Page 93 On Screen Menu Guide Page 95

Appendix Solutions to Common Problems Page 97

General Problems Page 97 Disc Playback Page 100 Radio Reception Page 101 Remote Control Page 102

Information Page 103 Glossary Page 106 Index Page 108 Specifications Page 110

C O

N T

E N

T S

E n

g lish

001DVX-S200-en 04.3.1, 11:08 AM5

6

Preparation

Supplied Accessories

Remote Control

Make sure all of the following accessories are in the box.

System Control Cable (5 m (1))

Batteries (2) (AA, R06, UM-3)

AM Loop Antenna

Indoor FM Antenna

Speaker Cables (Surround: 15 m (2), Front, Center: 5 m (3))

DVR-S200 NX-P200: NX-S200, NX-C200, NX-SW200

Video Pin Cable

Subwoofer Cable (1 pin, 5 m, (1))

Screws (M4 10) (Front, Surround Speakers (4))

Mounting Brackets (Front, Surround Speakers (4))

Non-Skid Pads (Subwoofer, 1 Set (4))

Fasteners (Center Speaker (2))

Non-Skid Pads (Front, Surround Speakers, 4 Sets (16))

About this Manual

explains additional operating tips that you may find useful.

indicates an operation that you should definitely perform.

In this manual, operations that can be performed on either the DVD/Super Audio CD Receiver or Remote Control are explained using the Remote Control.

In this manual, Remote Control descriptions and illustrations are based on models other than those in the U.K. or Europe. Any exceptions are clearly stated.

Introduction Your DVD Home Theater Sound System DVX-S200 consists of the following components.

DVD/Super Audio CD Receiver (DVR-S200) 1 unit

Speaker Set (NX-P200) Satellite Speakers (Front, Surround) (NX-S200) 4 units Center Speaker (NX-C200) 1 unit Subwoofer (NX-SW200) 1 unit

This Owners Manual was printed before final product development. After printing, some product specifications may change due to operational upgrades and other reasons. In this case, the specifications of the product itself will take precedence over the specifications in this manual.

In some cases, graphics or terms used may differ slightly from the actual product or packaging to facilitate explanation.

Explanations in this Owners Manual are based on the DVX-S200 (DVD/Super Audio CD Receiver (DVR-S200) and Speaker Set (NX-P200)). If you use speakers other than NX-P200, make sure to set the speaker size and volume level in advance. Page 63, Setting the Speaker Size Page 59, Adjusting the Speaker Volume Level

Advice

Please...

TV

CH

CINEMA

CH

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

ON SCREEN MENU

TEST

RETURNSTATUS

TV VOL VOLUME

MUTE

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

SET MENU

ENTER (U.S.A., Canada, Korea, Asia and General models)

(Europe, U.K. and Australia models)

002DVX-S200-en 04.3.1, 11:09 AM6

B asic

7

Preparation

Preparing the Remote Control Put the batteries in the Remote Control.

Preparing the Speakers The Front Speakers, Surround Speakers, Center Speaker and Subwoofer have special roles based on the type of sound each produces. The Front Speakers produce front channel sound (stereo) and sound effects. The Surround Speakers produce surround sound and sound effects. The Center Speaker produces sound oriented toward the center of the screen such as dialog or vocals. The Subwoofer produces bass sounds and the LFE signal contained in Dolby Digital and DTS.

You can secure the Center Speaker, Front/Surround Speakers or Subwoofer in place using fasteners or non-skid pads. You can hang the Front and Surround Speakers from the wall or attach them to optional speaker stands. See page 54, Placing the Speakers (NX-P200).

Placing the Speakers

Place the speakers as shown in the diagram below.

If the television (monitor) image is distorted, place the speakers away from the television.

Front Speakers (L, R) Place the Front Left and Right Speakers an equal distance from the ideal listening position. The distance of each speaker from each side of the video monitor should be the same.

Center Speaker Align the front face of the center speaker with the front face of your video monitor. Place the speaker as close to the monitor as possible (such as directly over or under the monitor) and centrally between the front speakers.

Surround Speakers (L, R) Place these speakers behind your listening position, facing slightly inwards, approximately 1.8 m (6 feet) above the floor.

Subwoofer The position of the Subwoofer is not so critical, because low bass sounds are not highly directional. But it is better to place the Subwoofer near the Front Speakers. Turn it slightly toward the center of the room to reduce wall reflections.

Press the h mark and slide off the back cover. Insert the two supplied batteries (AA, R06, UM-3) into the battery compartment.

Close the back cover.

Center Speaker

Front Speaker (L)

Front Speaker (R)

Surround Speaker (R)

1.8 m (6 feet)

Surround Speaker (L)Subwoofer

Advice Note

Check +/- polarity

Press h

E n

g lish

P rep

aratio n

002DVX-S200-en 04.3.1, 1:07 PM7

8

Connecting the Speakers and TV Connect the power cord after connecting the speakers and TV.Please ...

Connect the cable core with the color band near the tip to the + connector. Be careful, if you reverse the cables, the sound will be unnatural.

3 2 Cable core Color

band

Lever

1 Press the lever down. 2 Insert the speaker cable core

into the hole. 3 Release the lever and the

lever will snap back into place.

1 Speaker Cable (Red)

Connect the plug to the jack of the same color. Insert it firmly. Red, green, white: Face the tab upwards and insert. Gray, blue: Face the tab downwards and insert.

Tab

Red

Green

White

Blue

Tab

Gray

Speaker Cable (Gray)

Surround Right Speaker

Front Right Speaker

Please

Do not allow the speaker cable cores to touch each other. Do not use excessive force when inserting plugs, connectors or jacks as they can be damaged.

Preparation

Please ...

003DVX-S200-en 04.3.1, 11:10 AM8

9

VIDEO Y PB PR

S VIDEO (DVD ONLY)

COMPONENT VIDEO (480p/480i) (DVD ONLY)

MONITOR OUT

SPEAKERS

CENTER FRONT

SURROUND

FRONT

SURROUND

IN OUT

VIDEO 1 VCR VIDEO 2 MD/CD-R DIGITAL AUDIO OPTICALSUBWOOFER

OUT SYSTEM

CONNECTOR

LR

SPEAKER IMPEDANCE: 6 MIN.

R

L

75 UNBAL

FM ANT

GND

AM ANT

OUTININOUTININ

VIDEO IN

VIDEO

INPUT SYSTEM CONNECTOR

GND

AM ANT

AV

Surround Left Speaker

Front Left Speaker

Center Speaker

Speaker Cable (Green)

Speaker Cable (White)

TV

Connect the power cord after making all other connections.

Turn off the TV before connecting.

Video Pin Cable

DVD/Super Audio CD Receiver

Speaker Cable (Blue)

System Control Cable

Subwoofer Cable

Connect to the S-video or Y/PB/PR jack on the TV.

Connect the power cord after making all other connections.

Use a commercially available S-video cable to connect the S VIDEO MONITOR OUTPUT to your TVs S-video input.

Useful tip

Preparation P

rep aratio

n

Subwoofer

Connecting with S-video

E n

g lish

AV MONITOR OUT (U. K. and Europe models only) If your monitor has only one jack for video input, you can use CinemaStations SCART output jack for connecting directly to the monitor. This connection provides the best picture quality. See page 96 when the screen does not appear properly.

003DVX-S200-en 04.3.1, 11:10 AM9

10

POWER

TV

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

Basic Operations

Viewing a DVD Its time to play a DVD. Select a disc and begin from step 1.

Turn on the TV.

Use the TV remote control or power switch.

Switch TV Input. Use the TV remote control or the input switch button on the television. For example, switch to video input 1 if CinemaStation is connected to video input 1.

Press POWER.

CinemaStation turns on. The CinemaStation Display lights up.

Press f on the CinemaStation.

The disc tray slides out.

004DVX-S200-en 04.3.1, 11:10 AM10

11

B asic O

p eratio

n s

DVD/CD

CINEMA

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

E n

g lish

Basic Operations

Place a disc in the tray.

Place the disc with the label side facing up.

Hold the disc by its edge and hole in the center to avoid touching the surface of the disc.

Please ...

Press f on the CinemaStation.

The disc tray slides in.

Press DVD/CD.

CinemaStation enters DVD/CD mode.

004DVX-S200-en 04.3.1, 11:10 AM11

12

Basic Operations

A B C D E

POWER

CHCH

TV CH

SLEEP

PRESET PRESET

A B C D E

ON SCREEN MENU

TEST

RETURNSTATUS

TV VOL VOLUME

SET MENU

ENTER

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

ON SCREEN MENU

SET MENU

TV

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

Press p.

The DVD starts playing.

Press s to stop playback.

To change discs Press f on CinemaStation to eject the disc. Set another disc in the tray and press f.

Press POWER to turn off.

Eject the disc before turning off the power. After finished playing, press f on CinemaStation to eject the disc. Then press f once more to close the disc tray.

004DVX-S200-en 04.3.1, 11:10 AM12

13

B asic O

p eratio

n s

i

i Basic Operations

Handy Features

TV

CHCH

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

ON SCREEN MENU

TEST

RETURNSTATUS

TV VOL VOLUME

SET MENU

ENTER

TV

CHCH

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

ON SCREEN MENU

TEST

RETURNSTATUS

TV VOL VOLUME

SET MENU

ENTER

CHCH

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

A-BREPEAT

ON SCREEN MENU

RETURNSTATUS

SET MENU

ENTER

CH

CINEMA

CH

TEST

RETURNSTATUS

TV VOL VOLUME

MUTE

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

SET MENU

ENTER

CHCH

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

A-BREPEAT

ON SCREEN MENU

RETURNSTATUS

SET MENU

ENTER

E n

g lish

Useful

Selecting the Audio Language 1 While holding down SHIFT,

press AUDIO. 2 While viewing the TV

screen, press h or g to select the audio language you want. The audio language changes each time you press AUDIO while holding down SHIFT. Press ON SCREEN to turn off the On Screen Menu.

This selection is available when the DVD disc contains multi-language audio.

Selecting the Subtitle Language 1 While holding down SHIFT,

press SUBTITLE. 2 While viewing the TV

screen, press h or g to select the subtitle lan- guage you want. Select None to turn off the subtitle. The subtitle language changes each time you press SUBTITLE while holding down SHIFT. Press ON SCREEN to turn off the On Screen Menu.

This selection is available when the DVD disc contains multi-language subtitles.

Moving Forward and Backward To fast reverse: Press e. To fast forward: Press r. To move to the start of the currently playing or previous chapter: Press t. To move to the start of the next chapter: Press y.

Adjusting the Audio Volume

Press + to increase the volume and - to decrease. Pausing Playback

Press d. To resume playback press w.

1 ja

2 ja

3 en

Audio

2 jaSub-title

1 ja

3 en

004DVX-S200-en 04.3.1, 11:10 AM13

14

Basic Operations

Handy Features

TV

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

TV

CHCH

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

ON SCREEN MENU

TEST

RETURNSTATUS

TV VOL VOLUME

SET MENU

ENTER

Useful Features

Switching the Viewing Angle While holding down SHIFT, press ANGLE. The video angle changes each time you press ANGLE while holding down SHIFT.

Restarting Playback from the Stop Position (Memory Resume)

Pressing a during playback enables Memory Resume. CinemaStation memorizes the stop position. Pressing w starts playing back the disc from the stop position.

You can change the angle with h, g, or Number buttons, instead of ANGLE. Press ON SCREEN to turn off the On Screen Menu.

Advice

2

4Angle

3

5

This selection is available when the DVD disc contains multi-angle content.

004DVX-S200-en 04.3.1, 11:11 AM14

15

B asic O

p eratio

n s

Basic Operations i

i

Try It Out!

CH

CINEMA

CH

TEST

RETURNSTATUS

TV VOL VOLUME

MUTE

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

SET MENU

ENTER

E n

g lish

Useful Features

Enhancing the Sound Presence CinemaStation is loaded with a variety of DSP Programs, so you can experience from the raw excitement of a rock concert to the breathtaking space of a cinemagraphic spectacle. See page 16, Finding the Best DSP Effect.

Turning off the Sound Press MUTE on the Remote Control. Press it again to turn on the sound.

Controlling the DVDs Your Children Can View You can set the Parental Control level and lock discs. See page 81, Protecting Your Children from Undesirable Material.

Enhancing Video Quality CinemaStation uses progressive image playback (available only for NTSC Signal Output) to render the full beauty of DVD video. You can connect a television that has component video input jacks to CinemaStations COMPONENT VIDEO jacks and enjoy progressive scan imaging. See page 80, Enjoying High-Quality Video.

Answers to Common Problems

I cannot change the audio or subtitle language

The disc may have only one audio and one subtitle language.

I followed each step correctly but the disc doesnt play.

Some discs have a Disc Menu or DVD Menu. Your settings may change if you use this type of menu.

No subtitles appear

Check the disc jacket to make sure subtitles are available.

004DVX-S200-en 04.3.1, 11:11 AM15

16

Experiment with different sound field effects until you find the DSP Program that you feel best matches your source.

CinemaStation has other DSP Programs not listed below. See page 65, Selecting DSP Program Effects.

CinemaStation cannot use any DSP Program when playing a Super Audio CD.

Sound Presence

Finding the Best DSP Effect Changing the DSP effect based on listening and viewing content

Select a DSP Program for the movie or music and experience the sound of a movie theater or concert hall. Follow the chart below to select the DSP Program that offers the acoustic qualities you want.

Advice

What do you want to do? Next selection

Watch a movie

Watch live entertain- ment

Listen to music

Watch a sports broadcast

Play video games

An action-packed thriller

Romantic or comic drama

Popular science fiction with loads of effects

Grand spectacle

Experience the digital surround sound of a movie theater

Feel the excitement on the big stage

Classical concert

Live jazz

Rock Concert

Home party

Baseball and soccer

Feel the power and momentum of the game

005DVX-S200-en 04.3.1, 11:11 AM16

17

S o

u n

d P

resen ce

Action

Drama

Sci-Fi

Spectacle

Theater

Music Video

Classic Hall

Jazz Club

Rock Concert

5ch Stereo

MOVIE

MUSIC

SPORTS

GAME

Finding the right DSP Program

Action Enhances the stereoscopic effect for a thrilling sense of presence only found in an action movie.

Drama Expresses surround sounds softly so that voice and dialog are clear and crisp.

Sci-Fi (Science Fiction) Fills the space with music and sound that have an eerie sense of reality. Suitable for serious science fiction that has a good story line.

Spectacle Expresses super-wide spaces. Suitable for movies that have a powerful visual impact.

Theater Preserves the power of Dolby or DTS Surround for experiencing the rich acoustical presence of a movie theater.

Music Video Magnifies the feeling of listening to live rock or jazz in a concert hall. The screen image and sound field space stretch out to the fullest, engulfing you in an atmosphere of excitement.

Classic Hall (The Munich Philharmonic Hall) Puts you in a front row seat at the Munich Philharmonic Hall, surrounded in calm, voluptuous sound.

Jazz Club (The Bottom Line) Reproduces the acoustics of sitting right in front of the stage at The Bottom Line, a popular New York City jazz club. Experience the lively, realistic throb of a wide stage.

Rock Concert (The Roxy Theater) Recreates the acoustic personality of a nightclub seating for an audience of about 460.

5ch Stereo Fills the space with sound and allows all listeners to enjoy the same high-quality sound no matter where they are sitting or standing in the room. A DSP Program that is especially suitable for home parties.

Live Sports In a live stereo sports broadcast, announcer voices are central, engulfed in the cheers and emotional whirl of the stadium.

Game Gives TV games extra depth and surround. You can enjoy TV games with monaural or stereo sound.

Selecting a DSP Program

Remote Control

Press MOVIE repeatedly to display DSP Programs.

Remote Control

Press MUSIC repeatedly to display DSP Programs.

Remote Control

Press SPORTS.

Remote Control

Press GAME.

E n

g lish

Sound Presence

005DVX-S200-en 04.3.1, 11:11 AM17

18

Advanced Features

Names and Functions of Parts

Top and Front

Buttons for amplifier and disc operations a Stops disc playback.

d Pauses disc playback.

INPUT Selects an input source. Press this button until you find the source you want to watch or listen to. Selects an audio input signal. You can set the priority level for the audio input signals when the equipment is connected to both OPTICAL IN jack and AUDIO IN jack. (See page 78.)

VOLUME Adjusts the overall sound volume. Turn right to increase the volume and left to decrease the volume.

Disc tray Receives your disc.

Display Displays DSP Program names, setting values and playback information.

w Starts disc playback.

DSP Selects a DSP Program. Press this button until you find the DSP Program you want. To select another DSP Program group, hold down this button. See the diagram shown on the left.

t/e, r/y Selects the previous/next track or chapter. Continue pressing to fast forward or fast reverse.

f Opens and closes the disc tray.

STANDBY/ON Switches the unit between ON and STANDBY. No audio will be heard for a few seconds after power is switched on. STANDBY mode uses a little energy to receive an infrared signal from the Remote Control.

Remote Control Sensor Receives signals from the Remote Control.

Action

Drama

Sci-Fi

Spectacle

Theater

Music Video

Classic Hall

Jazz Club

Rock Concert

5ch Stereo

Live Sports

Game

PL Normal

PL II Movie

PL II Music

STEREO

Holding down DSP.

Press DSP.

DSP button operation

(phones) jack Connects your headphones. When selecting a DSP Program, you can enjoy SILENT CINEMA. (See page 70.)

PROGRESSIVE (NTSC only) Switches DVD playback between progressive and interlace outputs. (See page 80.)

006DVX-S200-en 04.3.1, 11:12 AM18

19

Advanced Features A

d van

ced F

eatu res

Buttons for tuner operations Press INPUT on CinemaStation or press TUNER on the Remote Control to select Tuner mode. In Tuner mode, the buttons below function as described.

About memory backup If you disconnect the power cord from the outlet, CinemaStation will memorize the settings listed to the right for about a week. Set them again if those settings are erased after a week.

Volume Subwoofer, Center and Surround L/R Speakers output

levels (See page 59.) SET MENU options (See page 89.) Sleep Timer settings (See page 79.) Preset radio stations (See page 41.) DSP Program settings

Delay Time (See page 72.) Dolby Pro Logic II Music settings (See page 68.)

A d

van ced

A d

van ced

F eatu

res

A/B/C/D/E Selects preset groups (A, B, C, D, E) for FM/AM stations. (See page 41.)

d PRESET/TUNING u Selects a Preset Number. Searches a radio station. (See page 39.)

PRESET/BAND Selects FM or AM tuning mode or Preset mode. (See page 39.)

MEMORY Stores received stations for Preset Tuning. (See page 41.)

AUTO/MANL Switches between Auto Tuning and Manual Tuning modes. (See pages 39 and 40.) Press this button to set CinemaStation to Auto Tuning mode (AUTO indicator lights up), or press this button to set CinemaStation to Manual Tuning mode (AUTO indicator goes out).

E n

g lish

006DVX-S200-en 04.3.1, 11:12 AM19

20

Advanced Features

CinemaStation Display

MATRIX PCM TITLE TRACK CHAP VIRTUAL SILENT MULTI2CH REP A-B ALL AUTO ST MEMORY

TUNEDPS PTY RT PTY

CT HOLD

PROGRESSIVE

DIGITAL

DVD VCD CD 888888888888

PL DSP PROG SLEEP

MATRIX PCM TITLE TRACK CHAP VIRTUAL SILENT MULTI2CH REP A-B ALL AUTO ST MEMORY

TUNED PROGRESSIVE

DIGITAL

DVD VCD CD 888888888888

PL DSP PROG SLEEP

PS PTY RT PTY

CT HOLD

PROGRESSIVE Lights up when PROGRESSIVE is activated.

Decoder indicator Lights up when an internal decoder is working.

DSP Lights up when a DSP sound field program is selected.

DSP Program indicator Lights up when a DSP Program is selected.

VIRTUAL Lights up when Virtual Cinema DSP is enabled.

SILENT CINEMA indicator Lights up when using a DSP Program with headphones for SILENT CINEMA.

SLEEP Lights up when using the Sleep Timer.

PCM Lights up when playing PCM signal such as CDs.

Program, Repeat indicator PROG: Lights up during Program Play. REP: Lights up during Repeat Play of a title, chapter or

track. REP ALL: Lights up during Repeat Play for whole

disc. REP A-B: Lights up during A-B Repeat.

ST Lights up when receiving a strong FM radio signal in Auto Tuning or Auto Preset mode.

Disc indicator DVD: Lights up while a DVD disc is set in the disc tray. VCD: Lights up while a VCD disc is set in the disc tray. CD: Lights up while a music CD disc is set in the disc tray.

AUTO Lights up when using Auto Tuning or Auto Preset in Tuning mode.

Stop (Pause) indicator Lights up when stopping or pausing disc playback.

Title, Track, Chapter indicator TITLE: Lights up when showing the title. TRACK: Lights up when showing the track. CHAP: Lights up when showing the chapter.

MEMORY Blinks when memorizing (presetting) an FM/ AM radio station.

Playback indicator Lights up during disc playback.

RDS indicator (U. K. and Europe models only) Lights up when receiving an RDS signal. In PTY SEEK mode the PTY HOLD indicator lights up.

TUNED Lights up when receiving an FM/AM broadcast.

Main Display Shows Input Source and DSP Program names, Radio Station Frequency, Preset Numbers and other info. Shows chapter or track number, elapsed time and other info during disc playback.

MULTI, 2CH MULTI: Lights up when playing a multi-channel Super Audio CD. 2CH: Lights up when playing a 2-channel Super Audio CD.

006DVX-S200-en 04.3.1, 11:12 AM20

21

Advanced Features A

d van

ced F

eatu res

30 30

Remote Control Features As shown on the left, CinemaStation is composed of three main parts. Remote Control button operations change depending on the mode, so it is possible to control all Amplifier, DVD/CD and Tuner functions with a single remote unit.

For example, in Amp mode the 3 button is used to select Matrix 6.1, but in DVD/CD mode, it functions as a numerical button that specifies time, track and other numbers.

To switch modes, follow the steps below. Amp mode: Press AMP. DVD/CD mode: Press DVD/CD. See page 23, DVD/CD

Mode Button Names and Functions. Tuner mode: Press TUNER.

For details on Tuner operations, see page 39, Listening to the Radio.

The Remote Control can also operate a television or VCR connected to CinemaStation. However, it is first necessary to enter the manufacturer code for the equipment in the Remote Controls memory. See page 84, Storing Manufacturer Codes in the Remote Control.

Some reminders when using the Remote Control Do not spill water or tea, or drop anything on the unit. Do not leave the unit in the following places.

Near a stove, bath or hot and humid place. In a dusty place. In an extremely cold place.

When the batteries run down, replace them When the batteries grow old, the effective operation distance decreases considerably. When that happens, replace the batteries with two new ones. Once you take the old batteries out, replace them within two minutes to preserve the memory in the Remote Control.

Use the Remote Control within 6 m (20 feet) of the CinemaStation and point it toward the Remote Control Sensor.

Using the Remote Control

Replace worn out batteries as soon as possible. Do not use a new battery with one that has been used before. Do not use different types of batteries (for example, alkaline with manganese) together. Each type of battery has its own

characteristics. If a battery starts leaking, dispose of it immediately. Be careful not to let leaking battery acid come into contact with you or your

clothing. Before inserting new batteries wipe the compartment clean.

TV

POWER POWER

AUDIO

/DTS SELECT STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

CINEMA

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

TUNER

AMP

DVD/CD

TV

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW CENTER SURR

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

Notes

CinemaStation AMP Decoder selection SET MENU

DVD/CD Playback Subtitles, audio language selection

FM/AM Radio station reception Radio station preset

Amp mode Tuner mode

3 button

Within 6m (20 feet)

E n

g lish

DVD/CD mode

006DVX-S200-en 04.3.1, 11:12 AM21

22

Advanced Features

Amp Mode Button Names and Functions

Press AMP before starting operations.

The purple color on the Remote Control indicates Amp mode.

Buttons with an asterisk (*) mark work even if you do not press AMP before starting operations.

Advice

TV

CH

CINEMA

CH

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

ON SCREEN MENU

TEST

RETURNSTATUS

TV VOL VOLUME

MUTE

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

SET MENU

ENTER

DSP Program buttons* Selects one of four DSP Programs: MOVIE, MUSIC, SPORTS or GAME. (See pages 16 and 17.) The MOVIE and MUSIC groups contain multiple sound field programs. Press the button repeatedly and select the effect you like.

VOLUME +/-* Adjusts the overall volume level. Press + to increase the volume and - to decrease the volume.

TEST Outputs a test tone. (See page 59.)

SET MENU Enters the SET MENU. (See page 89.)

SLEEP* Sets the Sleep Timer. (See page 79.)

Volume level buttons Adjust speaker volume level. (See page 61.) SW +/-: Adjusts the Subwoofer volume. CENTER +/-: Adjusts the Center Speaker volume. SURR +/-: Adjusts the volume of the Surround Speakers.

STEREO Switches between normal stereo sound and audio with a sound field effect. (See page 75.) Select STEREO to listen to audio with no sound field effect from the Front L/R Speakers.

MATRIX 6.1 Sets the Matrix 6.1 decoder. (See page 65.) In most cases, the Matrix 6.1 decoder works automatically once Dolby Digital Surround EX or DTS ES discs start playing. However, for some disc types, you may have to set the decoder using this button.

q/DTS, SELECT Switches between Dolby Digital and DTS decoders. After pressing q/DTS, repeatedly press SELECT to select a decoder. (See page 74.)

POWER (a/I)* Switches the CinemaStation between ON and STANDBY.

NIGHT Sets the CinemaStation to Night Listening mode. (See page 71.)

h, g, q, w Adjusts the test tone and SET MENU.

MUTE* Turns off the sound. Press again to return to the previous sound volume. This button works in every mode.

Input Selection buttons* Selects a source to operate with the Remote Control. (See pages 26 and 27.) To operate a VCR, CD or MD recorder, you need to set the manufacturer code for the VCR or MD/CD-R button.

Infrared signal transmitter Sends an infrared signal to the CinemaStation.

AMP Puts the Remote Control in Amp mode.

Input Selection buttons for U.K. and Europe models are as shown.

CINEMA

DVD/CD VCR VIDEO

TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

U.K. and Europe models

006DVX-S200-en 04.3.1, 11:12 AM22

23

Advanced Features A

d van

ced F

eatu res

DVD/CD Mode Button Names and Functions

Press DVD/CD before starting operations.

The green color on the Remote Control indicates DVD/CD mode.

Advice

TV

CH

CINEMA

CH

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

ON SCREEN MENU

TEST

RETURNSTATUS

TV VOL VOLUME

MUTE

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

SET MENU

ENTER

STATUS Shows type of disc, play/stop status, playing time and other info.

DVD/CD Puts the Remote Control in DVD/CD mode.

While holding down SHIFT, press one of the following buttons to enable the corresponding operation. 7REPEAT: Enables Repeat Play. 8AB: Enables settings for A-B Repeat. 2AUDIO: Switches the audio language of the DVD video. 3ANGLE: Switches the angle of the DVD video. 4SUBTITLE: Switches the subtitle language of the DVD video.

s (Stop) Stops disc playback.

e (Pause) Pauses disc playback.

h (Play) Starts disc playback.

MENU Shows the Disc Menu on the TV.

RETURN Returns the Disc Menu to one position before the current screen.

h, g, q, w/ENTER Adjusts On Screen Menu and other settings.

Number buttons (1-9, 0) Input numerals for track numbers and others.

w, f Fast forwards and reverses.

b, a (Skip) Moves to the start of a disc track.

ON SCREEN Shows the On Screen Menu on the TV. (See pages 24 and 93.)

E n

g lish

006DVX-S200-en 04.3.1, 11:12 AM23

24

Advanced Features

Using the On Screen Menu The On Screen Menu includes Preference, Toolbar and Setup. Perform operations using the TV screen.

Preference: You can adjust picture contrast, sharpness and other picture qualities of the DVD or video CD to your liking.

Toolbar: You can use Program Play, Disc Navigation and other handy playback features.

Setup: You can adjust DVD playback controls such as the default subtitle language and screen size.

Useful functions

Press ON SCREEN. The On Screen Menu appears.

CH

CINEMA

CH

ON SCREEN MENU

TEST

RETURNSTATUS

TV VOL VOLUME

MUTE

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

SET MENU

ENTER

g g , , ,hg

ON SCREEN

Setting default subtitle and audio languages

Program

View

Play Option

Search

Toolbar

Preferences

Setup

Adjusting the picture quality such as contrast or brightness

Setting the Status Display

Using Program Play

Using zoom and angle view

Selecting audio and subtitle languages, and learning about the disc structure

Finding a scene or track to view or listen to

Using the Parental Control

Fine-tuning TV screen settings

Setting Playback Control

On Screen Menu

007DVX-S200-en 04.3.1, 11:12 AM24

25

A d

van ced

F eatu

res Advanced Features

Press h or g to navigate the Main Menus, then press w.

On Screen Menu

Press h or g to navigate the Submenus, then press w.

Press h, g, q or w to select or set items.

Preference

Toolbar

Setup

Features

Picture

Program

View

Play Option

Search

Access

TV

Language

Features

Video shift Saturation Contrast Color settings (Colour settings) Brightness Sharpness

Status window

Clear All Tracks Program Play list (Playlist)

Zoom Angle Chapter Preview

Audio Disc Navigation Sub-title (Subtitle)

Frame by Frame Fast Time Slow

Disc Lock Parental level Enter PIN Change PIN

TV shape TV System Video Output*

Default Sub-title (Default Subtitle) Country Menu Language Default audio

PBC

E n

g lish

*U.K. and Europe models only.

Digital output Audio Menu

Refer to On Screen Menu Guide on pages 95 and 96.

007DVX-S200-en 04.3.1, 11:13 AM25

26

Selecting the Media Device

Selecting the Equipment CinemaStation provides you with a variety of playback options, including video discs, music CDs and MP3 discs. You can connect a VCR or video game console and increase your home entertainment possibilities. For connecting the equipment you want, follow the chart below.

What would you like to play? Equipment you use

Video discs

Music CDs, MP3 discs or Super Audio CDs

FM/AM radio

Video tape

Video game or video camera

CinemaStation

CinemaStation

CinemaStation

CinemaStation +

VCR

CinemaStation +

video game console or video camera

Play video CDs

MDs CinemaStation

+ CD or MD recorder

007DVX-S200-en 04.3.1, 11:13 AM26

S electin

g th

e M ed

ia D e vice

27

CINEMA

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

CINEMA

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

CINEMA

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

CINEMA

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

CINEMA

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

VIDEO 1 VIDEO 2

VCR

MD/CD-R

DVD/CD

TUNER

Selecting the Media Device

Press DVD/CD on the Remote Control.

To play a video disc, perform steps 1 to 10 on pages 10 to 12, Viewing a DVD. To play a music disc, perform steps 3 to 10 on pages 10 to 12, Viewing a DVD.

Complete the steps on pages 8 and 9, Connecting the Speakers and TV.

Complete the steps on pages 8 and 9, Connecting the Speakers and TV. Then connect the indoor FM Antenna and AM Loop Antenna to CinemaStation. See page 38, Connecting the Antennas.

Complete the steps on pages 8 and 9, Connecting the Speakers and TV. Then connect a VCR to CinemaStation. See page 46, Connecting Video Equipment.

Complete the steps on pages 8 and 9, Connecting the Speakers and TV. Then connect a game console or video camera to CinemaStation. See page 46, Connecting Video Equipment.

Press TUNER on the Remote Control.

To tune in your favorite channel, see page 39, Listening to the Radio.

Press VCR on the Remote Control.

Press VIDEO 1 or VIDEO 2 on the Remote Control.

Making the connections Selecting the equipment

E n

g lish

Complete the steps on pages 8 and 9, Connecting the Speakers and TV. Then connect a CD or MD recorder to CinemaStation. See page 50, Connecting Audio Equipment.

Press MD/CD-R on the Remote Control.

Press VIDEO for U.K. and Europe models.

Note

007DVX-S200-en 04.3.1, 11:13 AM27

28

Playing Video and Music Discs

Playback Methods CinemaStation provides you with a variety of playback methods, including the ability to select and quickly find a scene or tune.

Start operations after first pressing DVD/CD. CinemaStation enters DVD/CD mode to play a disc.

To skip chapters and tracks

To return to the previous chapter or track: Quickly press t twice. When you press t only once, playback starts from the beginning of the currently playing chapter or track. To advance to the next chapter or track: Press y.

To specify a track Enter the track number with the Number buttons. For a 1-digit number use buttons 1 to 9. For a 2-digit number, use the buttons 1 to 9 for the second digit place, and buttons 1 to 9 and 0 for the first digit place. For example:

To select track 17 press the 1 button followed by the 7 button. To select track 20 press the 2 button followed by the 0 button.

Selecting a Scene or Tune

Number buttons

TV

CH

CINEMA

CH

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

ON SCREEN MENU

TEST

RETURNSTATUS

TV VOL VOLUME

MUTE

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

SET MENU

ENTER

t y

CDVCD

Music CDDVD Video Video CD

In this manual, each type of disc has its own mark as shown below.

DVD-V VCD CD

CINEMA

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

DVD/CD

Super Audio CD

SA-CD

Super Audio CD There are different types of Super Audio CDs. 2-channel discs which contain stereo sound Multi-channel discs which contain multi-channel sound, up to 6 channels Hybrid discs which contain both stereo sound and multi-channel sound CinemaStation can play Super Audio CDs with the same operation as music CDs, and can reproduce high quality sound with a completely independent signal circuit for playing Super Audio CDs. (See page 37.)

SA-CD

DVD-V CDVCD SA-CD

008DVX-S200-en 04.3.1, 11:13 AM28

29

Playing Video and Music Discs P

layin g

V id

eo an

d M

u sic D

iscs

You can also use the On Screen Menu to operate Frame Advance, Fast Forward/Reverse and Slow Advance/Reverse. In addition to those, you can use Frame Reverse from the On Screen Menu. See page 93, Using the On Screen Menu.

The Skip feature may not work properly when using Playback Control on page 36 to play a video CD. If you use Fast Forward/Reverse while playing a Dolby Digital or DTS disc, the Speakers do not output any sound. Slow Reverse is not available for a video CD.

Frame Advance

Press d to pause playback.

Press d.

To return to normal play Press w.

Slow Advance/Reverse

Press d to pause playback.

To return press e or to advance press r. To Slow Reverse, press e. Each time you press the button, the speed changes (- 1/8, -1/4 or 1/2). To Slow Advance, press r. Each time you press the button, the speed changes (1/8, 1/4 or 1/2).

TV

CH

CINEMA

CH

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

ON SCREEN MENU

TEST

RETURNSTATUS

TV VOL VOLUME

MUTE

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

SET MENU

ENTER

d

w

re

Advice

Notes

E n

g lish

VCDDVD-V

DVD-V VCD

To return to normal play Press w.

To Fast Forward and Fast Reverse

Perform while playing. To Fast Reverse: Press e. Each time you press the button, the speed changes (D4, D8 or D32). To Fast Forward: Press r. Each time you press the button, the speed changes (4, 8 or 32).

To pause playback

Pressd while playing. Press w to return to normal playback.

D32 and 32 are not available for CD playback.

Note

VCDDVD-V

DVD-V CDVCD SA-CD

CD SA-CD

008DVX-S200-en 04.3.1, 11:14 AM29

30

Playing Video and Music Discs

Specify an elapsed time for playback (Time Search) Perform operations using the TV On Screen Menu.

TV

CH

CINEMA

CH

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

ON SCREEN MENU

TEST

RETURNSTATUS

TV VOL VOLUME

MUTE

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

SET MENU

ENTER

g

hON SCREEN

ENTER

g g

Press ON SCREEN. Make sure that Toolbar is selected.

Press w to select Play Option.

Press g to select Search.

Press w to select Time.

Press w or q to select 0:00:00 (hour, minute or second) with the cursor. Then enter time with the Number buttons. You can specify the time only within the current track or title, not the whole disc.

Press ENTER, then press ON SCREEN to turn off the On Screen Menu. When pressing ENTER, playback starts from the time position you specified in step 5.

Number buttons Program

View

Play Option

Search

Toolbar

Preferences

Setup

Frame by Frame

Fast

Time

Slow

Search

View

Play Option

0:00:28

Time

Frame by Frame

Fast

Slow

0:02:09Time

Frame by Frame

Fast

Slow

Cursor

008DVX-S200-en 04.3.1, 11:14 AM30

31

Playing Video and Music Discs P

layin g

V id

eo an

d M

u sic D

iscs

TV

CH

CINEMA

CH

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

ON SCREEN MENU

TEST

RETURNSTATUS

TV VOL VOLUME

MUTE

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

SET MENU

ENTER

g

hON SCREEN

ENTER

g g

Customizing Playback Order (Program Play)

Playback your favorite chapters and tracks in the order you want.

Perform operations using the TV On Screen Menu.

Program

View

Play Option

Search

Toolbar

Preferences

Setup

Clear all

Tracks

Program

Play list

Program

View

Play Option

T1 C1

Program

Tracks

Clear all

Play list

E n

g lish

VCD CD

Press ON SCREEN. Make sure that Toolbar is selected.

Press w, then repeatedly press h to select Program.

Press w, then press h to select Tracks. Then press w.

E.g. DVD video

E.g. CD

T1Tracks

Clear all

Program

Play list

DVD-V SA-CD

008DVX-S200-en 04.3.1, 11:14 AM31

32

Playing Video and Music Discs

TV

CH

CINEMA

CH

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

ON SCREEN MENU

TEST

RETURNSTATUS

TV VOL VOLUME

MUTE

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

SET MENU

ENTER

g

hON SCREEN

ENTER

g g

Playback Control is not available during Program Play of a video CD.

Press q to return to the screen in step 3, and press ON SCREEN to turn off the On Screen Menu. Program Play starts. Press w to start Program Play when Program Play does not start.

Advice

Note

Once Program Play is set, the PROG indicator lights up in the CinemaStation Display.

Chapter 1Title 1

Title 9

Title 10

Title 2

Title 3

Select the chapter or track to add to Program Play.

E.g. DVD video Press h or g to select the title number to add, then press ENTER.

Perform step 4 until you add all desired chapters or tracks.

Press h or g to select the chapter number to add, then press ENTER.

Chapter 1Title 1

Title 9

Title 10

Title 2

Title 3

E.g. CD Press h or g to select the track number to add, then press ENTER.

Track 2

Track 14

Track 1

Track 3

Track 4

008DVX-S200-en 04.3.1, 11:14 AM32

33

Playing Video and Music Discs P

layin g

V id

eo an

d M

u sic D

iscs

CHCH

ON SCREEN MENU

TEST

RETURNSTATUS

SET MENU

ENTER

g

hON SCREEN

g g

CHCH

ON SCREEN MENU

TEST

RETURNSTATUS

SET MENU

ENTER

g

hON SCREEN

g g

Check Program Play content

Delete Program Play

Perform steps 1 to 2 in Customizing Playback Order (Program Play) on page 31.

Press w, then press g to select Play list (Playlist). Then press w. The list appears in the specified order.

Press h or g to scroll through the list.

Perform steps 1 to 2 in Customizing Playback Order (Program Play) on page 31.

Press w, then press h to select Clear All. Then press w. Clear changes to Cleared, and all Program Play content is deleted.

E n

g lish

CHCH

ON SCREEN MENU

TEST

RETURNSTATUS

SET MENU

ENTER

g

hON SCREEN

g g

Turn on/off Program Play

Perform steps 1 to 2 in Customizing Playback Order (Program Play) on page 31.

Press w to select Program. Then press w.

Press h or g to select On or Off.

CinemaStation automatically sets Program menu item to On after Program Play starts. The setting does not change even if Program Play finishes, so you can restart Program Play by pressing w. To return to normal playback, select Off for Program menu item in the On Screen Menu. Even if you set it to Off, the playlist remains in the memory, so you can use the previous play list by setting it to On.

008DVX-S200-en 04.3.1, 11:14 AM33

34

Playing Video and Music Discs

You can repeat a favorite track, chapter or entire disc. You can also repeat certain parts you specified as many times as you like.

TV

CH

CINEMA

CH

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

ON SCREEN MENU

TEST

RETURNSTATUS

TV VOL VOLUME

MUTE

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

SET MENU

ENTER

SHIFT

REPEAT

Once Repeat Play is selected, the Repeat mode indicator lights up in the CinemaStation Display. REP indicates title, chapter and track repeat REP ALL indicates entire disc repeat

Repeat Play may not work properly with some DVD video discs. Repeat Play will not work during Menu Play of a video CD that is using Playback Control.

Repeating a Disc or Track (Repeat Play) DVD-V VCD CD

Play back a disc. To repeat a chapter or track first start playing it. See page 28, Selecting a Scene or Tune.

While holding down SHIFT, press REPEAT to select Repeat mode. Every time you press the button, the display on the TV screen changes as shown below.

Advice

Notes

Off (Normal playback)

Repeat (Repeat Play for currently playing chapter)

Disc (Repeat Play for currently playing disc)

Title (Repeat Play for currently playing title)

Off (Normal playback)

Repeat (Repeat Play for currently playing track)

Disc (Repeat Play for currently playing disc)

DVD video

Video CD/CD

SA-CD

SA-CD

Off (Normal playback)

Repeat (Repeat Play for currently playing track)

Area (Repeat Play for currently playing Area)

009DVX-S200-en 04.3.1, 11:14 AM34

35

Playing Video and Music Discs P

layin g

V id

eo an

d M

u sic D

iscs E

n g

lish

A-B Repeat may not work properly with some DVD video discs. You can use A-B Repeat only within one track or title.

TV

CH

CINEMA

CH

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

ON SCREEN MENU

TEST

RETURNSTATUS

TV VOL VOLUME

MUTE

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

SET MENU

ENTER

SHIFT

A-B

Repeat between two points (A-B Repeat) DVD-V VCD CD

Specify the start and end of a favorite segment (points A and B) then playback between those two points as much as you like. You can specify a part within one title or track.

Play back a disc.

While holding down SHIFT at the start position (point A), press A-B. Repeat A appears on the TV screen.

The REP A- indicator lights up in the CinemaStation Display.

While holding down SHIFT at the end position (point B), press A-B. A/B appears on the TV screen. A-B Repeat starts.

Advice

Advice

Notes

The REP A-B indicator lights up in the CinemaStation Display.

To return to normal playback

While holding down SHIFT, press A-B. A/B Off appears on the TV screen, and A-B Repeat cancels.

SA-CD

009DVX-S200-en 04.3.1, 11:15 AM35

36

Playing Video and Music Discs

Many DVDs or video CDs that have Playback Control include an original menu. You can use the menu for skipping to a favorite title or chapter and switching audio or subtitle language.

CH

CINEMA

CH

ON SCREEN MENU

TEST

RETURNSTATUS

TV VOL VOLUME

MUTE

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

SET MENU

ENTER

g

h

ENTER

MENU

g g

TV

CHCH

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

ON SCREEN MENU

TEST

RETURNSTATUS

O VOLUME

SET MENU

ENTER

t

RETURN

y

Playback Control is not available during Program Play.

Using a Disc Menu

Navigate a DVD Disc Menu

Use Video CD Playback Control (PBC) (Menu Play)

Press MENU. A menu appears on the TV screen.

Depending on the disc, a menu may automatically pop up when playback starts.

Advice

Select items with h, g, q, w and press ENTER. If operating instructions appear in the menu, follow them and repeat step 2.

If you play a video CD that includes Playback Control, a menu will appear on the TV screen. From the menu you can select the scenes and information that interest you. In this manual, using the menu screen to play media is called Video CD Menu Play.

Number buttons: For selecting the desired item. RETURN: For returning to the previous screen. y: For moving to the next screen. t: For returning to the previous screen.

Note

Number buttons

sing a isc enu

009DVX-S200-en 04.3.1, 11:15 AM36

37

Playing Video and Music Discs P

layin g

V id

eo an

d M

u sic D

iscs E

n g

lish

Playing a Super Audio CD

Using the TV screen, selected area and tracks of the Super Audio CD can be played back.

Turn on the TV and switch the input source to this unit. Insert the disc. (The track display screen of the Multi-channel appears.)

Press j to display the area selection screen.

Stereo

Multi-channel

CD-DA

Select Multi-channel, Stereo or CD-DA area using h and g and press w. E.g. When the disc contains Multi-channel, Stereo and CD-DA areas.

Area can be selected only when the Super Audio CD is stopped.

When Multi-channel or Stereo is selected, output is only from the speakers. (Only the sound from the front channel is output from the headphones.)

Select a track using h and g, and press ENTER to start playback.

Notes

You can play MP3 music that was recorded onto a CD-R or CD-RW by a computer.

If you use the CinemaStation to playback MP3 discs recorded on a computer, each folder on the disc is designated an Album, and each file in each folder a Track.

CinemaStation is compatible with a bit rate range of 32, 64, 96, 128, 192 or 256 kbps. CinemaStation is also compatible with variable bit rate encoded MP3 files.

CinemaStation is compatible with a sampling frequency of 32, 44.1 or 48 kHz.

Repeat Play You can use Track Repeat and Album Repeat to repeat your favorite track and disc. See page 34, Repeating a Disc or Track (Repeat Play).

Program Play You can playback your favorite tracks in the order you want. See page 31, Customizing Playback Order (Program Play).

Playback status on the TV screen You can check the playback status (e.g. disc type) along with the total and elapsed playing time of the current track on the TV screen.

Depending on the way you assign folder or file names when you record the MP3 disc, the CinemaStation may play tracks in a different order from the order they were recorded in.

Depending on recording conditions, some discs cannot be played back.

Advice

Notes

Root : Album (Folder)

: Track (File)

MP3 Playback Features

009DVX-S200-en 04.3.1, 11:15 AM37

38

Listening to the Radio

Connecting the Antennas CinemaStation includes an AM Loop Antenna and indoor FM Antenna. Use the supplied antennas in areas with good radio wave reception. Connect each antenna into its jack properly.

Y PB PR

COMPONENT VIDEO (480p/480i) (DVD ONLY)

MONITOR OUT

IN OUT

DIGITAL AUDIO OPTICALSUBWOOFER

OUT SYSTEM

CONNECTOR

75 UNBAL

FM ANT

GND

AM ANT

The AM Loop Antenna can be detached from its stand and attached to a wall. To improve reception, we recommend that you install an outdoor antenna. For details, contact your local Yamaha sound products

service center.

Install the supplied indoor FM Antenna and AM Loop Antenna away from this system. Even if you connect an outdoor AM antenna, be sure to still use the AM Loop Antenna.

Attach the Antenna to its stand.

Open the AM ANT and GND jack levers to the right. Insert the AM Loop Antennas cord cores into the AM ANT and GND jacks.

Close the lever to fasten the cord. Pull the cord lightly to make sure it is properly fastened.

Adjust the Antenna left and right and find the best position for reception.

Cord Core

Lever

Connecting the FM Antenna

Connect the supplied indoor FM Antenna to the FM ANT jack.

When connecting an outdoor FM antenna Use the antennas coaxial cable and a commercially available F-type connector to connect the antenna to the FM ANT jack. For details, ask the shop where you bought the outdoor antenna.

Earth (GND jack) The GND jack does not provide secure grounding. However when there is a lot of noise, connecting it may improve reception. To ground CinemaStation, connect one end of a vinyl coated wire to the GND jack and the other end to a commercially available grounding rod or copper sheet, and bury the rod or sheet in damp earth.

Connecting the AM Loop Antenna

Advice

Notes

Indoor FM Antenna (supplied)

AM Loop Antenna (supplied)

White

Black

AM ANT jack

GND jack

010DVX-S200-en 04.3.1, 11:16 AM38

39

Listening to the Radio L

isten in

g to

th e R

ad io

E n

g lish

Listening to the Radio CinemaStation provides several methods for tuning radio stations to help you find channels as easy as you can.

INPUT

Press PRESET/BAND to select either FM or AM. Each time you press, the mode changes in the order as follows: FM (Tuning mode) AM (Tuning mode) (Preset mode) FM (Tuning mode) ...

PRESET/BAND

AUTO/MANL

d PRESET/TUNING

PRESET/TUNING u

Selecting the Radio Tuner

Press INPUT repeatedly on CinemaStation until TUNER appears. The input source changes to Tuner (Radio) and you can listen to AM/FM broadcasts.

You can also press TUNER on the Remote Control to change the input source to Tuner.

Advice

Display

Selecting Radio Stations

You have two ways to select radio stations, Auto Tuning and Manual Tuning. Auto Tuning is quick and handy to use when radio signal reception is strong.

Select stations automatically (Auto Tuning)

If the colon (:) beside the Band indicator goes out, that means CinemaStation is in Tuning mode. Make sure the colon (:) is not lit up.

Advice

Press AUTO/MANL to set CinemaStation to Auto Tuning mode. When CinemaStation is set to Auto Tuning mode, the AUTO indicator lights up in the CinemaStation Display.

Press PRESET/TUNING u/d to select the radio station you want to receive. Press u to search for high-frequency stations or press d to search for low-frequency stations.

Display

Preset number Band

Preset group

Colon* Frequency

* Goes out in Tuning mode, lights up in Preset mode.

010DVX-S200-en 04.3.1, 11:16 AM39

40

Listening to the Radio

PRESET/BAND

AUTO/MANL

d PRESET/TUNING

PRESET/TUNING u

For stations with weak radio signals, tune manually.

If the radio waves are weak and Auto Tuning doesnt work, tune manually (Manual Tuning). When Auto Tuning finds a radio station, the TUNED indicator lights up and the frequency appears. Manually tuning in to an FM station will automatically change the reception mode to monaural to increase the signal quality.

Select your favorite stations by hand (Manual Tuning)

Perform step 1 in Select stations automatically (Auto Tuning) on page 39.

Press AUTO/MANL to set CinemaStation to Manual Tuning mode. When CinemaStation is set to Manual Tuning mode, the AUTO indicator goes out from the CinemaStation Display.

Press PRESET/TUNING u/d to select the radio station you want to receive. Hold down the button to continue the tuning search.

Advice

Display

010DVX-S200-en 04.3.1, 11:16 AM40

41

Listening to the Radio L

isten in

g to

th e R

ad io

E n

g lish

Up to 40 stations (5 Groups 8 Stations) can be automatically preset.PRESET/BANDA/B/C/D/E

MEMORY

AUTO/MANL

PRESET/TUNING u

d PRESET/TUNING

Setting Channels in Advance (Preset)

Presetting radio stations in memory helps you tune the preset radio stations using a few simple button operations.

Automatically preset FM stations in advance (Auto Preset)

Press PRESET/BAND to select FM.

Press AUTO/MANL to make the AUTO indicator light up.

Keep pressing MEMORY down for about 3 seconds. The Preset Number, MEMORY and AUTO indicators blink. After a few seconds, Auto Preset starts at the frequency currently displayed toward the higher frequency. When Auto Preset finishes the frequency of the last radio station memorized appears.

Customizing Auto Preset method You can specify the Preset Group or number to start tuning. You can also start Auto Tuning at the frequency currently displayed toward either the lower or higher frequency.

Perform steps 1 and 2 above, in Automatically preset FM stations in advance (Auto Preset).

Press MEMORY for about 3 seconds, then press A/B/C/D/E and PRESET/TUNING u/d to select the Preset Number you want to memorize first. Auto Preset will stop when the number memorized reaches 40 radio stations.

Press PRESET/BAND to turn off the colon (:), then press PRESET/TUNING u/d. When pressing d, Auto Preset starts at the frequency currently displayed toward the lower frequency, and when pressing u, Auto Preset starts at the frequency currently displayed toward the higher frequency.

Display

010DVX-S200-en 04.3.1, 11:16 AM41

42

Listening to the Radio

You can manually preset up to 40 radio stations. A/B/C/D/EMEMORY

PRESET/TUNING u

d PRESET/TUNING

When presetting a radio station, you can set the frequency and reception mode (stereo/monaural) at the same time. You can change the order of preset FM radio stations later. See page 43, Changing the Order of Preset Stations. If the number of radio stations that have been preset is less than 40, Auto Preset automatically stops after searching the whole

frequency range.

If a new radio station is preset for a Preset Number, the previously preset station for the Preset Number is deleted. In Auto Preset, only FM radio stations with a strong signal are set. To preset radio stations with a weak signal set reception mode

to monaural and preset manually.

Manually preset stations in advance (Manual Preset)

Select radio stations you want to preset. See page 39, Selecting Radio Stations. The frequency and broadcast band (FM or AM) of the tuned-in station appear in the CinemaStation Display.

Press MEMORY. The MEMORY indicator blinks for about 5 seconds in the CinemaStation Display, which means CinemaStation is ready to preset.

While the MEMORY indicator is blinking, press A/B/C/D/E to select the Preset Group (A to E). The Group appears. Check that the colon (:) beside the band indicator lights up.

While the MEMORY indicator is blinking, press PRESET/TUNING u/d to select a Preset Number (1 to 8). Press u for a larger number and d for a smaller number.

While the MEMORY indicator is blinking, press MEMORY. The selected Preset Group and Number, broadcast band (FM or AM) and frequency appear in the CinemaStation Display.

Repeat steps 1 to 5 to manually preset other radio stations.

Advice

Notes

Display

010DVX-S200-en 04.3.1, 11:16 AM42

43

Listening to the Radio L

isten in

g to

th e R

ad io

E n

g lish

You can tune in a radio station simply by selecting its Preset Number. Start operations after first pressing TUNER.

TV

CHCH

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

ON SCREEN MENU

TEST

RETURNSTATUS

TV VOL VOLUME

MUTE

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

SET MENU

ENTER

A/B/C/D/E

u PRESETPRESET d

TUNER

PRESET/TUNING u

PRESET/BAND

d PRESET/TUNING

Selecting a Preset Station (Preset Tuning)

Changing the Order of Preset Stations

Press A/B/C/D/E repeatedly to select the stations Preset Group. The Preset Group that appears in the CinemaStation Display changes each time you press A/B/C/D/E.

Press PRESET u/d to select the Preset Number. The Preset Group and Number, broadcast band (FM or AM) and frequency appear in the CinemaStation Display with the TUNED indicator lit up.

You can also perform Preset Tuning by repeatedly pressing A/B/C/D/E and PRESET/TUNING u/d on CinemaStation.

Advice

You can also change the order of preset stations.

Below is an example of the steps for switching the E1 and A5 radio stations.

Tune in the radio station preset to E1. Review the procedure above, Selecting a Preset Station (Preset Tuning).

Press PRESET/BAND for about 3 seconds. E1 and the MEMORY indicator will blink in the CinemaStation Display.

Tune in the radio station preset to A5 using A/B/ C/D/E and PRESET/TUNING u/d. A5 and the MEMORY indicator will blink in the CinemaStation Display.

Press PRESET/BAND. EDIT E1-A5 will appear in the CinemaStation Display and the preset stations will exchange places.

010DVX-S200-en 04.3.1, 11:16 AM43

44

Listening to the Radio

TV

CHCH

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200RDS WB56630

ON SCREEN MENU

TEST

RETURNSTATUS

TV VOL VOLUME

MUTE

SET MENU

ENTER

MODE STARTPTY SEEKFREQ/RDS

u PRESET

PTY SEEK START

PRESET d

FREQ/RDS

PTY SEEK MODE

Receiving RDS Stations (U.K. and Europe models only)

RDS (Radio Data System) is a transmission system for FM stations used in many countries.

RDS transmissions contain various types of information, including PS (Program Service), PTY (Program Type), RT (Radio Text), and CT (Clock Time). RDS works through cooperation among broadcasting stations.

FREQ/RDS Press this button when receiving an RDS station to switch between frequency and RDS mode. The RDS mode display may include PS, PTY, RT and CT, depending on the information a radio station provides.

PTY SEEK MODE Press this button to set the program type to search for.

PTY SEEK START Once the program type has been selected in PTY SEEK mode, press this button to begin the search.

PTY (Program Type)

RDS Modes

RDS supports four types of information: PS, PTY, RT and CT.

PS (Program Service) Shows the name of the RDS station broadcasting.

PTY (Program Type) Divides RDS broadcasts into the 15 genres shown at right.

RT (Radio Text) Shows RDS broadcast information (including song title, artist name) using up to 64 letters and numbers plus the umlaut letter. If the radio text contains other characters, they will appear with an underbar.

CT (Clock Time) Shows the current time updated once a minute. If data flow is interrupted, CT WAIT will appear.

NEWS

AFFAIRS

INFO

SPORT

EDUCATE

DRAMA

CULTURE

SCIENCE

VARIED

POP M

ROCK M

M.O.R. M

LIGHT M

CLASSICS

OTHER M

News

Current Affairs

General Information

Sports

Education

Drama

Culture

Science

Light Entertainment

Pops

Rock

Middle-Of-the-Road Music (easy-listening)

Light Classics

Serious Classics

Other Music

U.K. and Europe models

011DVX-S200-en 04.3.1, 11:17 AM44

45

Listening to the Radio L

isten in

g to

th e R

ad io

E n

g lish

Change RDS Mode

There are four RDS display modes. When an RDS station is broadcasting, PS, PTY, RT or CT mode indicators corresponding to the services provided light up in the CinemaStation Display. Press FREQ/RDS repeatedly to change among the modes supported by the currently tuned RDS station.

Notes When an RDS station is broadcasting, do not press FREQ/RDS until

one or more mode indicators light up in the CinemaStation Display. If you press FREQ/RDS before the mode indicators light up, CinemaStation may not be able to change modes.

RDS information not provided by a station cannot be selected. If the RDS stations signal transmission is too weak, CinemaStation

may not be able to use the service fully. In particular, radio text uses a lot of bandwidth, so it may not be available even when other modes are selectable.

RDS information may not transmit under poor conditions. In this case, press AUTO/MANL to set CinemaStation to Manual Tuning mode. This changes reception to monaural and may help RDS information reappear when you switch to RDS display mode.

If outside interference disrupts an RDS station broadcast, RDS information may suddenly disappear and ...WAIT appears in the CinemaStation Display.

About PTY SEEK

Press PTY SEEK MODE to set CinemaStation to PTY SEEK mode. The program type of the tuned in station or NEWS blinks in the CinemaStation Display.

Press PTY SEEK START to start searching all preset RDS stations. The selected program type flashes and the PTY HOLD indicator lights up while the search is in progress. If the search finds a station that matches the program type you selected, CinemaStation will tune it in. If the station tuned in is not the one you want press PTY SEEK START again to continue the search for other stations broadcasting the program type you selected.

Press PRESET u/d to select the program type you want. Your program type selection appears in the CinemaStation Display.

When you select the program type, CinemaStation automatically searches through all preset stations currently broadcasting for that type.

To cancel steps 1 or 2 Press PTY SEEK MODE twice.

PS

PTY

RT

CT

RDS mode OFF

011DVX-S200-en 04.3.1, 11:17 AM45

46

Using Other Equipment

Connecting Video Equipment Connect a VCR to CinemaStation to play or dub videos. You can also connect a game console or video camera.

Connecting a Game Console or VCR

Always read the owners manual of any equipment you want to connect.

VIDEO Y PB PR

S VIDEO (DVD ONLY)

COMPONENT VIDEO (480p/480i) (DVD ONLY)

MONITOR OUT

IN OUT

VIDEO 1 VCR VIDEO 2 MD/CD-R DIGITAL AUDIO OPTICALSUBWOOFER

OUT SYSTEM

CONNECTOR

R

L

75 UNBAL

FM ANT

GND

AM ANT

OUTININOUTININ

VIDEO

DIGITAL

OPTICAL

OUTPUT

OUTPUT

L

R

L

R

AUDIO

VIDEO

L

R

L

R

AUDIO

VIDEO

AUDIO

VIDEO

L

R

AUDIO

VIDEO

INPUT OUTPUT1 OUTPUT2 INPUT1 INPUT2

Please...

TV

Connection Cables

VCR

Game console or video camera

Or

CinemaStation

Use a commercially available Audio/Video cable. Use the supplied Video Pin Cable.

Audio/Video cable (commercially available)

Video Pin Cable (supplied)

When directly connecting the TV

with the VCR, you can play video tape on the VCR even if you turn

off CinemaStation.

Use a commercially available optical cable

Optical cable (commercially available)

The cable can be connected to either a VIDEO 1 or VIDEO 2 jack. (Only VIDEO jacks are available on U.K. and Europe models.)

011DVX-S200-en 04.3.1, 11:17 AM46

47

Using Other Equipment U

sin g

O th

er E q

u ip

m en

t E

n g

lish

TV

Use a commercially available audio cable.

CinemaStation

L

R

OUTPUT

AUDIO

VIDEO

VIDEO

VIDEO 1 VCR VIDEO 2

R

L

INOUTININ

Notes on the audio jacks You cannot simultaneously use both IN and OUT jacks when

the jack names are the same as each other. For example, the signal input from the VCR IN jack does not output from the VCR OUT jack.

CinemaStations digital and analog signal circuits are independent of each other, so analog input signals can only output from analog output jacks and digital input signals can only output from digital output jacks.

Notes on recording and playing video Perform a test recording before recording. Do not press ON SCREEN during recording a DVD video.

If you press ON SCREEN, the On Screen Menu appears, and both the video and On Screen Menu will be recorded.

It is not possible to record DSP effects. When you turn off the connected VCR power, playback sound

may become distorted and the volume reduced. In this case, turn on the VCR power.

Even if you adjust the audio volume, audio quality, or change the DSP Program during a video recording, it has no effect on the recorded sound.

Video recordings that you make cannot be used for any purpose other than private enjoyment without the consent of the copyright holder.

You cannot record from a copy protected DVD disc.

Connect a game console to a digital input If your game console has a digital output jack (optical), it can be connected to CinemaStations OPTICAL IN jack. See page 50, Connecting Audio Equipment to learn how to connect an optical jack. Connect the video output to CinemaStations VIDEO 1 IN or VIDEO 2 IN jack. (VIDEO IN jack on U.K. and Europe models)

Connect a TV to an audio input Enjoy TV sound with CinemaStation by connecting the TV audio output jack to the audio IN jacks of VIDEO 1 or VIDEO 2 (VIDEO IN jack on U.K. and Europe models). Press VIDEO 1 or VIDEO 2 on the Remote Control to input TV sound.

Note Press VIDEO for U.K. and Europe models.

011DVX-S200-en 04.3.1, 11:17 AM47

48

Using Other Equipment

Operating a VCR

For VCR operations, read your VCR owners manual.

TV

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

CINEMA

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

POWER

VCR

TV

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

CINEMA

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

POWER

VIDEO 1

VIDEO 2

Advice The Remote Control can also operate a television or VCR connected

to CinemaStation. However, it is first necessary to enter the manufacturer code for the equipment in the Remote Controls memory. See page 84, Storing Manufacturer Codes in the Remote Control.

Operate your VCR.

Turn on the TV.

Turn on the VCR.

Switch the TV input. For example, switch to video 1 if CinemaStation is connected to video input 1 on the television.

Press POWER to turn on CinemaStation.

Press VCR. CinemaStation can now output the VCR signal.

Playing a Video Game or Operating a Video Camera

For game console and video camera operations, read their respective owners manuals.

Play your game console or video camera.

Press VIDEO 1 or VIDEO 2 according to the jacks connected to the game console or video camera. CinemaStation can now output video signals (game console or video camera).

Press POWER to turn on CinemaStation.

Switch the TV input. For example, switch to video 1 if CinemaStation is connected to video input 1 on the television.

Turn on a game console or video camera.

Turn on the TV.

Note Press VIDEO for U.K. and Europe models.

011DVX-S200-en 04.3.1, 11:17 AM48

49

Using Other Equipment U

sin g

O th

er E q

u ip

m en

t E

n g

lish

Dubbing from a Video Camera to a VCR

For video camera and VCR operations, be sure to read their respective owners manuals.

TV

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

CINEMA

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

POWER

VIDEO 1

VIDEO 2

Turn on the TV.

Start playback on the video camera, then start recording with the VCR.

Prepare to record with the VCR. For example, switch the VCR input to external.

Press VIDEO 1 or VIDEO 2 according to the jacks connected to the video camera. CinemaStation can now input video signal (video camera).

Press POWER to turn on CinemaStation.

Switch the TV input. For example, switch to video 1 if CinemaStation is connected to video input 1 on the television.

Turn on the video camera and VCR.

CinemaStation VCR

TV

Note If you play a video source that uses scrambled or encoded signals to prevent it from being dubbed, the picture itself may be

disturbed due to those signals.

Connecting with SCART cable (U.K. and Europe models only) Do not connect CinemaStation to a monitor via a VCR. The copyright protection technology incorporated in CinemaStation may not allow the video to play.

Note Press VIDEO for U.K. and Europe models.

011DVX-S200-en 04.3.1, 11:17 AM49

50

Using Other Equipment

Connecting Audio Equipment You can connect a CD recorder or MD recorder to CinemaStation to record audio played on CinemaStation.

Connecting a CD or MD Recorder

Y PB PR

S VIDEO (DVD ONLY)

COMPONENT VIDEO (480p/480i) (DVD ONLY)

MONITOR OUT

IN OUT

VIDEO 2 MD/CD-R DIGITAL AUDIO OPTICALSUBWOOFER

OUT SYSTEM

CONNECTOR

75 UNBAL

FM ANT

GND

AM ANT

OUTININ

OUTPUT

OPTICAL

INPUTL

R

INPUTOUTPUT

Please...

For equipment connection, read the owner's manual of the equipment you want to connect.

Anti-dust cap When connecting an optical cable, first remove the dust cap attached to the OPTICAL jack. Store the cap in a safe place and re-attach it when the jack is not in use to prevent the jack from collecting dust.

Connection Cables

CD recorder or MD recorder

CinemaStation

Use a commercially available Optical Cable

Optical Cable (commercially available)

Anti-Dust Cap

Use a commercially available Audio Pin Cable.

Audio Pin Cable (commercially available)

You can connect a CD or MD recorder to MD/CD-R jacks, OPTICAL jacks or both.

011DVX-S200-en 04.3.1, 11:17 AM50

51

Using Other Equipment U

sin g

O th

er E q

u ip

m en

t E

n g

lish

CinemaStation cannot output a signal to the MD/CD-R OUT jacks even when receiving a signal from the MD/CD-R IN jacks.

CinemaStations digital and analog signal circuits are independent of each other, so analog input signals can only output from analog output jacks and digital input signals can only output from digital output jacks.

CinemaStations optical digital jack is designed based on EIA standards. If you use an optical cable that does not meet EIA standards, it may not function properly.

The digital jacks are compatible with PCM, Dolby Digital and DTS signals.

The OPTICAL IN jack is compatible with a digital signal that has a 96 kHz or less sampling frequency.

Press MD/CD-R to operate your CD or MD recorder. When connecting the CD or MD recorder to both MD/CD-R jacks and OPTICAL jacks and * Input Mode is set to AUTO, the OPTICAL jacks have priority over the MD/CD-R jacks. See page 78, Switching Input Modes.

Use * Input Assign in the SET MENU to assign the OPTICAL IN jack to VIDEO 1, VIDEO 2 (VIDEO on U.K. and Europe models), VCR or MD/CD-R. The default setting is MD/CD-R. For example, when connecting your game console to the OPTICAL IN jack, assign the OPTICAL IN jack to VIDEO 1, and press VIDEO 1 to start operating the game console.

Notes for setting the OPTICAL IN jack and the OPTICAL output signal

Set to MD/CD-R (default setting) CinemaStation cannot output a signal to the OPTICAL OUT jack even when inputting a signal from the OPTICAL IN jack.

Set to VIDEO 1, VIDEO 2 or VCR CinemaStation outputs a signal to the OPTICAL OUT jack when inputting a signal from the OPTICAL IN jack.

Notes on the digital audio jacks

For details about assigning OPTICAL IN jacks see page 89, Using the SET MENU.

CINEMA

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

VIDEO 1

MD/CD-R

Notes U.K. and Europe models only have VIDEO instead of

VIDEO 1 and VIDEO 2. VIDEO is used as VIDEO 1 in above models.

011DVX-S200-en 04.3.1, 11:17 AM51

52

Using Other Equipment

Perform a test recording before recording. It is not possible to record DSP effects. CinemaStation cannot output a Super Audio CD signal to the

OPTICAL OUT jack. To record a Super Audio CD signal, connect external devices (such as CD or MD recorder) to the analog output jacks and use it to record the signal.

When you turn off the connected CD recorder or MD recorder power, playback sound may become distorted and the volume reduced. In this case, turn on the CD recorder or MD recorder power.

Even if you adjust the audio volume, audio quality, or change the DSP Program during a video recording, it has no effect on the recorded sound. However, in DVD/CD mode, the output sound for recording may cut off if any of the operations below are performed. Do not perform any of the below during recording. Output a test tone. Change a DSP Program Connect/disconnect the headphones

CinemaStation can output a signal from the DIGITAL IN jack to the DIGITAL OUT jack. The signal input from the DIGITAL IN jack cannot output from the analog output jacks, and the signal input from the analog input jacks cannot output from the DIGITAL OUT jacks.

Do not use audio recordings that you make for any purpose other than private enjoyment without the consent of the copyright holder.

Timer Playback/Recording Combined with a commercially available audio timer, you can perform Timer Playback and Timer Recordings. Operations vary depending on the equipment and audio timer used, so be sure to read the relevant equipment owners manual.

Notes on recording and playing audio

011DVX-S200-en 04.3.1, 11:17 AM52

53

Using Other Equipment U

sin g

O th

er E q

u ip

m en

t E

n g

lish

When using Timer Playback/Recording, even if CinemaStation is in standby mode, the memory content (e.g. input source, AM/ FM frequency) is retained and used.

TV

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

CINEMA

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

POWER

Turn on the CD recorder or MD recorder power and get ready for recording.

Recording Audio from CinemaStation

Start recording with the CD recorder or MD recorder.

Switch CinemaStation input to the source you want and start playback. E.g. To play a CD: First press DVD/CD then play the CD.

Press POWER to turn on CinemaStation.

Input Selection buttons

Notes Even if you use DTS software to digitally record a DTS signal only noise will be recorded. CinemaStation cannot output a Super Audio CD signal to the digital jack. If you want to perform Timer Recording without hearing sound, turn the volume down before starting Timer Recording.

Advice

Playing a CD or MD

CINEMA

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

MD/CD-R

Read the owners manual of the equipment you want to operate before using it.

Advice

The Remote Control can operate a CD or MD recorder connected to CinemaStation. However, it is first necessary to enter the manufacturer code for the equipment in the Remote Controls memory. See page 84, Storing Manufacturer Codes in the Remote Control.

Turn on the CD recorder or MD recorder.

Start playback on the CD or MD recorder.

Press MD/CD-R. CinemaStation can now output audio signals received from a CD or MD recorder.

Press POWER to turn on CinemaStation.

011DVX-S200-en 04.3.1, 11:17 AM53

54

Creating the Best Listening Space

Placing the Speakers (NX-P200)

Make sure the top of the television is level. If the top of the television is not level, place the Center Speaker inside the TV rack or directly on the floor. In any case, make sure it is placed on a level surface.

When placing on top of the television, use the supplied fastener (two pieces) as shown in the picture on the left, between the bottom of the Center Speaker and top of the television to fasten.

Do not place on a television with top narrower than the bottom of the speaker. You may get injured if the speaker falls over.

Do not place if the top of the television is slanting. You may get injured if the speaker falls over.

After peeling off the fastener seal, do not touch the bonding surface. If you do, the bonding surface weakens, which later may cause the speaker to fall over.

Before attaching the fastener to the television, wipe the TV top clean. If the surface is dirty or wet tape will lose bonding strength, which later may cause the speaker to fall over.

Placing the Center Speaker

Placing the Subwoofer

Place the Subwoofer on a level hard floor.

Use non-skid pads on the bottom of the Subwoofer in the four corners as shown in the picture. This will prevent the Subwoofer from sliding when it vibrates and increase stability, preventing degradation of sound.

To get the most out of the sound field effects you need to place the speakers in the best positions. To guard against poor acoustics like sound blur make sure the speakers are stable. Also read page 7, Preparing the Speakers.

Notes Fastener

Peel off the seal

012DVX-S200-en 04.3.1, 11:18 AM54

55

C reatin

g th

e B est L

isten in

g S

p ace

Creating the Best Listening Space E

n g

lish

One speaker weighs about 1.0 kg (2.2 lb). Make sure you fasten screws only into a solid wall or pillar. Do not attach to a wall that is made of plaster, decorative veneer sheeting or other material that peels easily. If the screws come off and a speaker falls, somebody may get injured.

Do not attach the speakers using nails or two-sided tape. Vibration during use may cause the nails to loosen, tape to peel off and speakers to fall, resulting in injury.

CinemaStation may fall over if your feet or hands get caught in the speaker cable. Make sure the cables are fixed in place. After attaching everything, check the overall safety of your installation.

YAMAHA will bear no responsibility for accidents caused by improperly placed equipment or faulty installation methods.

Placing the Front and Surround Speakers

Attach to the wall using the two holes on the back of the Front and Surround Speakers.

Attach 2 screws (3.5 to 4 mm dia., commercially available) to each place you want to hang a Front or Surround Speaker.

Hang the speakers on the screws using the holes in the back of each speaker.

Make sure that the tapping screw enters the narrow part of the hole and the speaker is fixed securely in place.

As shown in the picture, attach the non-skid pads on the bottoms of the Front and Surround Speakers in the four corners. This stabilizes the speakers to prevent sliding. * Place on a stable, flat surface.

You can place the Front Speakers and Surround Speakers on the floor or a rack, or attach them to a wall. You can also mount them on commercially available speaker stands.

Note

Notes

Non-skid pad

Screws (3.5 to 4 mm dia., commercially available)

110 mm

10 mm

20 mm or more

When placing on the floor or a rack

When attaching to a wall

110 mm

012DVX-S200-en 04.3.1, 11:18 AM55

56

Creating the Best Listening Space

Use the supplied screw to attach the mounting bracket to the bottom of the speaker. The jutting part of the bracket enters the groove at the speaker base.

Use the bracket holes (60 mm spacing) to fasten the mounting bracket to the speaker stand. Use the screws (4 mm dia.), spring washers and washers.

Mounting bracket (supplied)

Screw (supplied)

60 mm

When attaching to a speaker stand and bracket

When attaching to a speaker stand and bracket, be sure to read their respective owners manuals.

When attaching to the optional SPS-200 Speaker Stands, you do not need to attach the supplied mounting brackets.

Advice

012DVX-S200-en 04.3.1, 11:18 AM56

57

C reatin

g th

e B est L

isten in

g S

p ace

Creating the Best Listening Space E

n g

lish

Yamaha Speaker Stand SPS-200 (Option) With the SPS-200 Speaker Stands, you can set the Front Speakers and Surround Speakers on the floor. (2 stands/set)

SPS-200

Using Commercially Available Speakers or Cables

Use speakers of the same manufacturer and quality, if possible. If the quality of each speaker differs, the voice of a moving person may become unnatural.

Advice

You can use commercially available speakers instead of the supplied Center Speaker, Front Speakers, Surround Speakers, or Subwoofer. You can also use commercially available speaker cables instead of the supplied cables.

Use a speaker with 6-ohm impedance or more. If a speaker with less than 6-ohm impedance is used, the protective circuit may trip or the speaker may malfunction.

Use magnetically shielded speakers. If these speakers still create interference with the monitor, place the speakers away from the monitor.

Make sure the speaker cable you use is the same thickness as the supplied cable.

* SPS-200 stands may not be available in certain regions.

Notes

012DVX-S200-en 04.3.1, 11:18 AM57

58

Creating the Best Listening Space

Push up the release button and pull out the supplied speaker cable from the connector.

Peel away about 10 mm of covering from the tip of the commercially available cable and firmly twist the cable cores. Not twisting firmly can cause a short.

Keep pushing up the release button and insert the cable cores of the commercially available cable. Match the speaker cable polarity (+/-) with the polarity indicator (+/-) of the connector.

Release your finger from the release button to fasten the cable.

Release button

10 mm

Polarity indicator

Polarity indicator

Changing the speaker cables

Release button

012DVX-S200-en 04.3.1, 11:18 AM58

59

C reatin

g th

e B est L

isten in

g S

p ace

Creating the Best Listening Space E

n g

lish

Adjusting the Speaker Balance with a Test Tone

TV

CH

CINEMA

CH

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

ON SCREEN MENU

TEST

RETURNSTATUS

TV VOL VOLUME

MUTE

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

SET MENU

ENTER

AMP VOLUME + /

TEST

g g

Adjusting the Speaker Volume Level The default settings of the Speakers are suitable for most conditions. However, depending on room conditions or listening position, you may need to adjust the Speaker volume level, especially when changing speaker or furniture position.

This adjustment is important because it brings out the maximum effect of the DSP Program, and faithfully reproduces the acoustic personalities of Dolby Pro Logic, Dolby Pro Logic II, Dolby Digital and DTS.

Even after performing the test tone, you may still like to adjust the speaker volume level for some sources. In this case see page 61, Adjusting the Speaker Volume Level During Playback.

You cannot adjust the volume level while connected to headphones. To adjust, disconnect your headphones.

Adjust the volume so that it is the same for each speaker from your listening position.

To adjust the sound, use the Remote Control from your listening position.

Press AMP.

Press TEST.

Note

Note

012DVX-S200-en 04.3.1, 11:18 AM59

60

Creating the Best Listening Space

If you raise the volume level of the Center and Surround L/R Speakers to + 10 dB and this is still less than the Front Speakers, set the * F. Level in the SET MENU to -10 dB and lower the volume level of the Front Speakers by about 1/3. If you change the volume level of the Front Speakers, adjust the volume level of the Center and Surround L/R Speakers once again.

Adjust the overall sound using the VOLUME +/- so that you can hear the test tone. The picture on the left shows the test tone order: LEFT (Front L Speaker) CENTER (Center Speaker) RIGHT (Front R Speaker) R SUR. (Surround R Speaker) L SUR. (Surround L Speaker) SUBWOOFER (Subwoofer). Each speaker outputs sound for about 2 seconds. The speaker currently outputting a test tone appears in the CinemaStation Display.

While a test tone is outputting from the speaker you want to adjust, press q or w and tune it to the same volume level as the Front Speakers. Only the speaker currently being adjusted produces a test tone.

While in test tone mode you cannot adjust the volume level of the Front Speakers which serve as the standard. If you need to adjust the volume level of the Front Speakers, exit the test tone mode and press VOLUME +/-.

When adjustment is finished, press TEST. The test tone stops.

Note

If * CENTER in the SET MENU is set to NON, the Center Speaker signal is distributed to the Front L/R Speakers at the same volume level and output. In this case, you cannot adjust the audio output level of the Center Speaker.

If * SUR. in the SET MENU is set to NON, you cannot adjust the volume level of the Surround L/R Speakers. The test tone skips the Surround L/R Speakers and continues its cycle.

If * BASS in the SET MENU is set to FRONT, the test tone skips the Subwoofer and continues its cycle. The test tone for Subwoofer is different from the others, but this is not a defect.

Notes

Advice

RIGHTLEFT

SUBWOOFER CENTER

L SUR. R SUR.

012DVX-S200-en 04.3.1, 11:18 AM60

61

C reatin

g th

e B est L

isten in

g S

p ace

Creating the Best Listening Space E

n g

lish

Adjusting the Speaker Volume Level During Playback

The volume level adjustment range is +10 dB to -10 dB. You cannot adjust the Left and Right Surround Speakers individually. The same adjustment level will be applied to both.

If the level adjusted during the sound test was different for Left and Right and one speaker was then tuned to a maximum of +10 dB or a minimum of -10 dB, the value cannot be adjusted any further up or down.

We recommend that you first adjust the speaker balance with a test tone. See page 59, Adjusting the Speaker Balance with a Test Tone.

If you change the speaker volume level with the SW, CENTER or SURR buttons, the levels you adjust with the test tone also change.

TV

CH

CINEMA

CH

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

ON SCREEN MENU

TEST

RETURNSTATUS

TV VOL VOLUME

MUTE

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

SET MENU

ENTER

AMP

SURR + /

SW + /

CENTER + /

Adjust the volume level of the Subwoofer, Center and Surround Left/Right Speakers, if you feel the speaker is unbalanced during audio playback.

Volume levels other than for Front Speakers can be adjusted.

Advice

Press AMP during playback.

Adjust the speaker volume level. To adjust the Subwoofer volume press SW +/-. To adjust the Center Speaker volume press CENTER +/-. To adjust the Surround Speakers volume press SURR +/-.

Depending on your settings in SET MENU, volume level adjustment may not be available for a speaker. If * CENTER is set to NON you cannot adjust the Center Speaker.

If * SUR. is set to NON you cannot adjust the Surround Speakers.

If * BASS is set to FRONT you cannot adjust the Subwoofer.

Advice

Note

012DVX-S200-en 04.3.1, 11:18 AM61

62

Creating the Best Listening Space

You can adjust the speaker volume level from 0 to 100%. The factory default setting is 100%, which is the maximum value.

You can adjust the speaker volume for 5ch Stereo DSP Program

Press AMP during playback.

Repeatedly press MUSIC and select 5ch Stereo.

Repeatedly press g or h, and select the speaker you want to adjust. The switching order is CT LEV RL LEV RR LEV CT LEV... To adjust the Center Speaker volume level, select CT LEV. To adjust the Surround L Speaker volume level, select RL LEV. To adjust the Surround R Speaker volume level, select RR LEV.

Press q or w and adjust the speaker volume level. When setting to 50%, the speaker volume becomes half, and when setting to 0%, you hear no sound from the Speaker.

The volume levels adjusted with the test tone or the CENTER or SURR buttons in 5ch Stereo mode are replaced with the setting with CT LEV, RL LEV or RR LEV. The actual volume you hear is the volume shown in the CinemaStation Display multiplied by the percentage you set for volume level.

If * CENTER is set to NON, you cannot adjust the Center Speaker. If * SUR. is set to NON, you cannot adjust the Surround Speakers.

TV

CH

CINEMA

CH

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

ON SCREEN MENU

TEST

RETURNSTATUS

TV VOL VOLUME

MUTE

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

SET MENU

ENTER

g

AMP

h

MUSIC

g g

Notes

Advice

Adjust speaker volume for 5ch Stereo DSP Program

012DVX-S200-en 04.3.1, 11:18 AM62

63

C reatin

g th

e B est L

isten in

g S

p ace

Creating the Best Listening Space E

n g

lish

Setting the Speaker Size

TV

CH

CINEMA

CH

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

ON SCREEN MENU

TEST

RETURNSTATUS

TV VOL VOLUME

MUTE

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

SET MENU

ENTER

g

AMP

h

g g SET MENU

Even if * FRONT is set to SML, when * BASS is set to FRONT, low tones below 90 Hz of the Front L/R channel signal will output from the Front Speakers.

If you select a sound field effect when * SUR. is set to NON, CinemaStation enters Virtual Cinema DSP mode. Settings made in Speaker mode are not reflected when connected to headphones.

To get the most out of the sound field effects, you need to use all 6 of the supplied speakers (Front, Center, Surround and Subwoofer). But depending on your listening objectives, you can turn off specified speakers.

When using any speaker other than YAMAHA Speaker Set NX-P200, you need to specify the speaker size.

You can specify these settings in Speaker mode.

Setting the Speaker Mode

Specify the speaker to produce no sound by setting * CENTER, * SUR. or * BASS.

When using other speakers, be sure to set the speaker size, and depending on your listening objectives set the Front Speaker level.

Press AMP.

Press SET MENU. * Speaker Set appears.

Press w.

Press h or g to select item you want to set.

Press q or w to change the setting.

Repeat steps 4 and 5 to set the needed item.

When exiting the SET MENU, press SET MENU. Pressing any one of the DSP Program buttons also exits the SET MENU.

Note

Advice

When a sampling digital signal over 48 kHz is input, some settings may not be reflected in the playback sound.

012DVX-S200-en 04.3.1, 11:18 AM63

64

Creating the Best Listening Space

* CENTER

Sets whether the Center Speaker is present or not, and sets the size of the Center Speaker.

Selection items: LRG (Large), SML (Small), NON (None)

Default setting: SML

LRG: Select this setting when using a big Center Speaker. The entire frequency band of the center channel signal is output as it is from the Center Speaker.

SML: Select this setting when using a small Center Speaker. A center channel signal with a low tone of 90 Hz or below is output from the speaker set to * BASS.

NON: Select this setting when not using a Center Speaker. The center channel signal distributes the same volume level to the Front L/R Speakers.

* FRONT

Sets the size of the Front Speakers.

Selection items: LRG (Large), SML (Small) Default setting: SML

LRG: Select this setting when using large Front Speakers. The entire frequency band of the front L/R channel signal is output as it is from the Front Left and Right Speakers.

SML: Select this setting when using small Front Speakers. A front L/R channel signal with a low tone of 90 Hz or below is output from the speaker set to * BASS.

* SUR.

Sets whether the Surround L/R Speakers are present or not, and sets the size of the Surround L/R Speakers.

Selection items: LRG (Large), SML (Small), NON (None)

Default setting: SML

LRG: Select this setting when using large Surround L/R Speakers or when using Surround L/R Speakers with surround subwoofers connected by speaker cables. The entire frequency band of the surround L/R channel signal is output as it is from the Surround Speakers.

SML: Select this setting when using small Surround L/R Speakers. A surround L/R channel signal with a low tone of 90 Hz or below is output from the speaker set to * BASS.

NON: Select this setting when not using Surround L/R Speakers. The surround L/R channel signal distributes the same volume level to the Front L/ R Speakers.

* BASS

Selects the speaker to output a LFE/BASS (low tone) signal.

Selection items: SWFR (Subwoofer), FRONT, BOTH Default setting: SWFR

SWFR: Select this setting when using a Subwoofer. The LFE and low tone (90 Hz and below) sound from other channels, depending on * CENTER, * FRONT and * SUR. settings, are output from the Subwoofer.

FRONT: Select this setting when not using a Subwoofer. The LFE and low tone (90 Hz and below) sound from other channels, depending on * CENTER, * FRONT and * SUR. settings, are output from the Front L/R Speakers.

BOTH: Select this item to mix low frequence tones of 90 Hz and below with a LFE channel when using a Subwoofer, independent of the Front Speaker Sound mode setting. The entire frequency band of the front L/R channel is output from both the Front L/R Speakers and Subwoofer. Sound can output from the Subwoofer during 2-channel or Dolby Surround playback.

* F. Level

Selects the Front Speaker level. When the Front Speaker volume level is extremely high and out of alignment with that of other speakers, you can lower the volume level and regain a balance.

Selection items: Nrm (Normal),-10 dB Default setting: Nrm

Nrm: Usually this setting is selected. -10 dB: Use this setting if the output level of the Center

or Surround Speakers is out of alignment with the Front Speakers. The volume level of the Front Speakers decreases 10 dB (about 1/3).

When BOTH is selected during Super Audio CD playback, output is only from the subwoofer.

Advice

012DVX-S200-en 04.3.1, 11:18 AM64

65

More Information about DSP (Surround) Effects M

o re In

fo rm

atio n

ab o

u t D

S P

(S u

rro u

n d

) E ffects

E n

g lish

Selecting DSP Program Effects To get the most out of CinemaStation, select a sound field based on how many speakers you want to use and the listening environment.

Select a sound field based on how many speakers you want to have sound.

For a 6-speaker plus surround back speaker setup, see page 65, Using Matrix 6.1.

For a 6-speaker setup, see page 67, Using All Speakers for CD or Video Playback.

For a 2-speaker setup, see page 69, Using Front Speakers Only for DSP Program (Virtual Cinema DSP).

Select a sound field based on your listening environment

For headphones, see page 70, Using a DSP Program with Headphones (SILENT CINEMA).

For evening enjoyment, see page 71, Using a DSP Program with Low Volume (Night Listening).

For setting a DSP Program to match your listening room, see page 72, Changing the Delay Time of a DSP Program.

Enjoy original Dolby and DTS sound

To listen to original Dolby or DTS sound as it is, see page 74, Reproducing the Original Dolby and DTS Sound.

To listen to stereo sound as it is, see page 75, Reproducing Stereo Sound.

Using Matrix 6.1

TV

CH

CINEMA

CH

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

ON SCREEN MENU

TEST

RETURNSTATUS

TV VOL VOLUME

MUTE

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

SET MENU

ENTER

AMP

MATRIX 6.1

Matrix 6.1 sound creates a realistic sense of sonic movement with a surround back sound.

You can enjoy Dolby Digital plus Matrix 6.1 or DTS plus Matrix 6.1 sound without adjusting any settings when you play a Dolby Digital Surround EX or DTS ES disc.

In addition to Dolby Digital Surround EX or DTS ES discs, you can also enjoy Matrix 6.1 sound with a 5.1 channel source. Selecting Matrix 6.1 with the MATRIX 6.1 button will enable the Dolby Digital plus Matrix 6.1 and DTS plus Matrix 6.1 decoder. The surround L/R channel will produce a surround back channel, making it possible to output sound from a virtual surround back speaker.

Press AMP.

Press MATRIX 6.1 to set. The display indicator switches in the following order each time you press MATRIX 6.1 : AUTO (auto-recognition) Matrix 6.1 (Matrix audio) OFF AUTO...

CinemaStation cannot use DSP Programs when playing Super Audio CDs.

Advice

013DVX-S200-en 04.3.1, 11:19 AM65

66

More Information about DSP (Surround) Effects

When the Matrix 6.1 decoder is working, the MATRIX indicator lights up in the CinemaStation Display. 6.1 appears beside the DSP Program name (For example: Action 6.1). Matrix 6.1 appears with Dolby Digital and DTS sound fields.

Some Dolby Digital Surround EX or DTS ES discs do not contain a signal (flag) that CinemaStation can use for auto recognition. To play this type of disc with 6.1-channel sound, press MATRIX 6.1 to select Matrix 6.1.

In the cases below, 6.1-channel sound cannot play even if you press MATRIX 6.1. If * SUR. is set to NON in the SET MENU. If sound effect is set to off (Stereo Playback). If headphones are connected. If a Dolby Digital KARAOKE source is playing. If you select 5ch Stereo DSP Program.

If you turn on the power once more after CinemaStation goes into standby, Matrix 6.1 returns to AUTO.

AUTO: When playing back a 6.1 channel source (Dolby Digital Surround EX or DTS ES), the sound is automatically switched either to Dolby Digital plus Matrix 6.1 or DTS plus Matrix 6.1 audio. Even if you play a 5.1 channel source with this setting, no virtual surround back speaker is created.

MATRIX 6.1: Select this item to play a 5.1 channel source with Matrix 6.1. Sound outputs from the virtual surround back speaker.

OFF: The Matrix 6.1 decoder is not enabled. Even if you play a Dolby Digital Surround EX or DTS ES disc, no sound outputs from the virtual surround back speaker.

Advice

Notes

013DVX-S200-en 04.3.1, 11:19 AM66

67

More Information about DSP (Surround) Effects M

o re In

fo rm

atio n

ab o

u t D

S P

(S u

rro u

n d

) E ffects

E n

g lish

Using All Speakers for CD or Video Playback

TV

CH

CINEMA

CH

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

ON SCREEN MENU

TEST

RETURNSTATUS

TV VOL VOLUME

MUTE

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

SET MENU

ENTER

AMP

SELECTq/DTS

You can also press the DSP button on CinemaStation to select PRO LOGIC II Movie or PRO LOGIC II Music.

Even if you play back a monaural source with Dolby Pro Logic II, CinemaStation cannot reproduce multi-channel sound.

Selecting Dolby Pro Logic II converts a 2-channel source into virtual multi-channels for enjoying sound using all speakers.

Play the 2-channel source.

Press AMP.

Press q/DTS.

Press SELECT repeatedly to select PRO LOGIC II.

Press q/DTS to select PRO LOGIC II Movie or PRO LOGIC II Music. Each time the button is pressed the selection switches between PRO LOGIC II Movie and PRO LOGIC II Music. Match your source with the appropriate selection item, Movie or Music.

Advice

Note

013DVX-S200-en 04.3.1, 11:19 AM67

68

More Information about DSP (Surround) Effects

TV

CH

CINEMA

CH

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

ON SCREEN MENU

TEST

RETURNSTATUS

TV VOL VOLUME

MUTE

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

SET MENU

ENTER

g

h

g g

Below are the Pro Logic II Music setting values (parameters).

PANORAMA

Gives front L/R channel sound a wraparound effect, distributed throughout the entire surround sound field, for an expansive feeling. Function: Expands the front sound field of Dolby Pro Logic II. Selection item: OFF/ON Default setting: OFF

DIM. (Dimension)

Adjusts the difference in volume between front and surround channels to the volume balance you desire. Function: Adjusts the difference between front surround sound field and surround volume. Variable range: -3 (stronger toward the surround direction) to +3 (stronger toward the front direction). Default setting: STD (Standard)

CT WIDTH

Distributes the center channel sound to the left and right. Function: Expands audio from the front sound field to the left and right. Variable range: 0 to 7. If set to 0 center channel sound will only output from Center Speaker. As the value rises center channel sound is incrementally distributed to the L/R Speakers. When set to 7, sound will only output from the L/R Speakers. Default setting: 3

You can change the settings (parameters) for Dolby Pro Logic II Music and adjust the sound field to match your listening space.

Perform steps 1 to 5 in Using All Speakers for CD or Video Playback on page 67, and select PRO LOGIC II Music.

Press h or g repeatedly to select PANORAMA, DIM. or CT WIDTH.

Press q or w to change the setting value.

Repeat steps 2 and 3 if you want to change other setting values.

Change the Dolby Pro Logic II Music setting

013DVX-S200-en 04.3.1, 11:19 AM68

69

More Information about DSP (Surround) Effects M

o re In

fo rm

atio n

ab o

u t D

S P

(S u

rro u

n d

) E ffects

E n

g lish

Using Front Speakers Only for DSP Program (Virtual Cinema DSP)

TV

CH

CINEMA

CH

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

ON SCREEN MENU

TEST

RETURNSTATUS

TV VOL VOLUME

MUTE

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

SET MENU

ENTER

AMP

SET MENU

g

h

g g

For Virtual Cinema DSP, the VIRTUAL indicator lights up in the CinemaStation Display.

In the cases below, even if * SUR. is set to NON in the SET MENU, Virtual Cinema DSP does not function. When you select the following DSP Programs: 5ch Stereo; PL Normal; Dolby Digital Normal or DTS Normal; PL II Movie or

PL II Music. When sound field effects are off (Stereo Playback). When a digital audio sampling frequency over 48 kHz is input. When using a test tone. When listening through headphones.

Since Virtual Cinema DSP processes the sound input source, you can virtually reproduce surround speakers, and enjoy a DSP Program with only your Front L/R Speakers.

Play the source.

Press AMP.

Select a DSP Program.

Set * SUR. to NON in the SET MENU. See page 63, Setting the Speaker Mode.

Advice

Notes

DSP Program buttons

013DVX-S200-en 04.3.1, 11:19 AM69

70

More Information about DSP (Surround) Effects

CINEMA

TEST

RETURNSTATUS

TV VOL VOLUME

MUTE

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

When SILENT CINEMA is on, the SILENT CINEMA indicator lights up in the CinemaStation Display. CinemaStation mixes LFE channel audio and other channel audio. When headphones are connected, sound does not output from any speaker regardless of whether sound field effect is on or off. When you do not select any DSP Program, the headphone produces normal stereo sound.

If CinemaStation inputs a digital audio sampling frequency over 48 kHz, SILENT CINEMA does not function.

Connect your headphones to the (phones) jack on CinemaStation and enjoy multi-speaker simulation called SILENT CINEMA.

Using a DSP Program with Headphones (SILENT CINEMA)

Connect your headphones to the (phones) jack on CinemaStation.

Play the source.

Select a DSP Program.

Advice

Note

DSP Program buttons

(phones) jack

013DVX-S200-en 04.3.1, 11:19 AM70

71

More Information about DSP (Surround) Effects M

o re In

fo rm

atio n

ab o

u t D

S P

(S u

rro u

n d

) E ffects

E n

g lish

TV

CH

CINEMA

CH

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

ON SCREEN MENU

TEST

RETURNSTATUS

TV VOL VOLUME

MUTE

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

SET MENU

ENTER

AMP

NIGHT

All DSP Programs are available in Night Listening mode. Night Listening mode does not work when listening through headphones.

You can control the big sound effects and focus on listening clearly to speech. Enjoy a DSP Program even in the evening at a low volume.

Using a DSP Program with Low Volume (Night Listening)

Play the source.

Press AMP.

Select a DSP Program.

Press NIGHT to activate Night Listening mode. Night L. ON appears in the CinemaStation Display.

To return to normal play Press NIGHT to deactivate Night Listening mode. Night L. OFF appears in the CinemaStation Display.

Advice

DSP Program buttons

013DVX-S200-en 04.3.1, 11:19 AM71

72

More Information about DSP (Surround) Effects

Changing the Delay Time of a DSP Program

TV

CH

CINEMA

CH

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

ON SCREEN MENU

TEST

RETURNSTATUS

TV VOL VOLUME

MUTE

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

SET MENU

ENTER

AMP

SELECTq/DTS

g

h

g g

You can also adjust the Delay Time of Matrix 6.1 DSP Program.

Depending on the source it is possible to over or under adjust the Delay Time and create an unnatural sound effect. While adjusting the Delay Time, you hear no sound temporarily.

Each DSP Program is designed to draw out the maximum effect from the source audio. CinemaStation provides the DSP Programs with optimum value of parameters including reflected sound, reverberant sound and Delay Time.

Among these parameters, you can change the Delay Time to match to your Speaker positions.

Delay Time is the time gap in playback between front speaker audio and surround speaker audio. The bigger the value becomes the later the surround audio plays back, and the bigger the sound space feels.

Delay Time is preset at an optimum value for each DSP Program. In most cases, the default value will work well for your listening enjoyment. But depending on the audio source or listening environment, you can adjust each DSP Program the way you like.

Play the source.

Press AMP.

Select a DSP Program. To select a Movie, Music, Sports, or Game DSP Program, press the appropriate DSP Program button (MOVIE, MUSIC, SPORTS or GAME). To select a Dolby Digital, Dolby Pro Logic or DTS, after pressing q/DTS, repeatedly press SELECT until you come to the item you want.

Press h or g. The DELAY indicator appears in the CinemaStation Display.

Press q or w to adjust the Delay Time.

Advice

Notes

DSP Program buttons

013DVX-S200-en 04.3.1, 11:19 AM72

73

More Information about DSP (Surround) Effects M

o re In

fo rm

atio n

ab o

u t D

S P

(S u

rro u

n d

) E ffects

E n

g lish

Program Program Name

Default Setting Group (ms)

MOVIE 1

Action 20

Action 6.1 15

2 Drama 20

Drama 6.1 15

3 Sci-Fi 20

Sci-Fi 6.1 15

4 Spectacle 23

Spectacle 6.1 15

5 Theater 20

Theater 6.1 5

MUSIC 1 Music Video 21

2 Classic Hall 30

3 Jazz Club 30

4 Rock Concert 15

SPORTS 1 Live Sports 10

GAME 1 Game 36

Program Name

Default Setting (ms)

PL Normal (Dolby Pro Logic)

15

Normal (Dolby Digital, DTS)

5

Matrix 6.1 (Dolby Digital, DTS)

5

PL II Movie (Dolby Pro Logic II Movie)

15

PL II Music (Dolby Pro Logic II Music)

5

Default values for Delay Time Dolby Digital, Dolby Pro Logic and DTS

013DVX-S200-en 04.3.1, 11:19 AM73

74

More Information about DSP (Surround) Effects

Reproducing the Original Dolby and DTS Sound

TV

CH

CINEMA

CH

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

ON SCREEN MENU

TEST

RETURNSTATUS

TV VOL VOLUME

MUTE

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

SET MENU

ENTER

AMP

SELECTq/DTS

You can play back and enjoy movie sound processed with Dolby Digital, Dolby Pro Logic or DTS. Enjoy smooth, precise and flowing audio of the original sound design.

Play the source.

Press AMP.

Press q/DTS. The suitable Program is selected depending on the input source. Dolby Digital: Normal appears, and qindicator lights up. DTS: Normal appears, and t indicator lights up. When the 2-channel source (Dolby Pro Logic) is selected, first, press q/DTS. Then, press SELECT to select PL Normal.

013DVX-S200-en 04.3.1, 11:19 AM74

75

More Information about DSP (Surround) Effects M

o re In

fo rm

atio n

ab o

u t D

S P

(S u

rro u

n d

) E ffects

E n

g lish

Reproducing Stereo Sound

TV

CH

CINEMA

CH

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

ON SCREEN MENU

TEST

RETURNSTATUS

TV VOL VOLUME

MUTE

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

SET MENU

ENTER

AMP

STEREO

If * BASS in the SET MENU is set to BOTH or * FRONT is set to SML, a low tone is output from the Subwoofer.

If sound field effects are off, no sound will output from the Center Speaker or Surround L/R Speakers. The volume may become very low if you turn off sound field effects and set * D. Range to MIN in the SET MENU. In this

case, turn on sound field effects. If sound field effects are off and you play Dolby Digital or DTS audio, the volume balance of the Front L/R Speakers may be

disturbed. This is because the dynamic range becomes compressed and the channel sound set in * Speaker Set in the SET MENU mixes and outputs with the front L/R channel sound.

Play the source.

Press AMP.

Press STEREO. The STEREO indicator lights up in the CinemaStation Display. If sound field effects are off, you will have normal stereo playback. Press STEREO once more to turn on the sound field effect.

Advice

Notes

You can enjoy the 2-channel (stereo sound) source only with the Front L/R Speakers.

013DVX-S200-en 04.3.1, 11:19 AM75

Types of Input Signals

76

Types of Input Signals You can check the type of input signal and format from the CinemaStation Display.

You can also set the input mode to select the digital/analog entry sequence or to only input a specified signal.

TV

CH

CINEMA

CH

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

ON SCREEN MENU

TEST

RETURNSTATUS

TV VOL VOLUME

MUTE

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

SET MENU

ENTER

AMP

STEREO

g

Checking Sound Information (Input Signal Information Display)

During playback, you can show input signal type, format and sampling frequency information in the CinemaStation Display.

Play the source.

Press AMP.

Press STEREO. Stereo playback begins.

Press g. Input signal information appears. Depending on the input source, input signal information changes each time you press g.

014DVX-S200-en 04.3.1, 11:20 AM76

Types of Input Signals

77

Typ es o

f In p

u t S

ig n

als E

n g

lish

Note on digital signals that exceed 48 kHz

CinemaStations digital input jack can input a sampling frequency up to 96 kHz. For details read the owners manual of the device connected to the digital input jack. Keep in mind the points below when inputting a digital signal that exceeds 48 kHz. DSP Programs are not selectable. You can only listen to

normal 2-channel stereo from the Front Speakers. During playback, you cannot adjust the volume level of

Center and Surround L/R Speakers. Depending on the * Speaker Set setting in the SET

MENU, the Subwoofer may output sound.

Input signal information

(Format) Shows the input signal format. When the digital input cannot be recognized, the mode is set to analog.

Input Signal Format Display

Analog Audio Analog

PCM Audio PCM

Dolby Digital Audio Dolby DGTL

DTS Audio DTS

Other Digital Signals Unknwn DGTL

(Audio Channels) Shows the number of audio channels an input signal contains (only when Dolby Digital or DTS is input). For example, in: 3/2/LFE indicates 3 Front Channels, 2 Surround Channels and LFE. 1+1 indicates Main + Sub in bilingual broadcasts or other 2 channel audio, and MLT indicates 3-channel or more multi-channel audio.

fs Shows the frequency sampling of an input signal (only when digital signal is input). If the sampling frequency cannot be measured, unknown appears.

rate (bit rate) Shows the amount of data an input signal contains per second (only Dolby Digital and DTS). If the bit rate cannot be measured, unknown appears.

flg (flag) Shows a recognition signal (flag), in an input signal and initiates an action (only Dolby Digital and DTS). If the flag cannot be recognized, None appears.

014DVX-S200-en 04.3.1, 11:20 AM77

Types of Input Signals

78

Switching Input Modes

TV

CH

CINEMA

CH

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

ON SCREEN MENU

TEST

RETURNSTATUS

TV VOL VOLUME

MUTE

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

SET MENU

ENTER

It is possible to switch Input mode even if you press INPUT on CinemaStation for more than one second. When Input mode is set to AUTO and a Dolby Digital or DTS signal is input, the most suitable decoder is automatically

selected. The following happens when set to Input mode and DTS is played:

CinemaStation detects the DTS signal and automatically switch to DTS mode (t indicator lights up). Once DTS audio finishes playback, the t indicator may blink, and while it blinks only DTS audio can be played back. Immediately after DTS audio finishes playback, if you want to play normal PCM audio, reset the Input mode to AUTO.

If the DTS signal is interrupted when you perform Search or Skip, the t indicator may blink. If this condition continues for over 30 seconds, the Input mode automatically changes from DTS to normal digital (PCM) and the t goes out.

Using * Input Mode in the SET MENU you can set whether to use the Input mode specified previously when CinemaStation was turned on or return to AUTO.

It is not possible to select ANLG with the DVD/CD Input Selection button. You cannot switch input modes when the input jack you select with the Input Selection button can only accept an analog input

signal. To play back DTS, set the Input mode to AUTO or DTS. Do not set it to ANLG. If you do, audio may not output or you may

hear noise.

You can playback most sources without a problem with the AUTO setting (factory default setting). Then depending on your needs, you can select the priority level for digital and analog input signals, and specify formats such as DTS.

Press the Input Selection button for current input source until the desired input mode appears in the CinemaStation Display.

AUTO: Input signal can be selected in the order below. 1) Digital signal 2) Analog signal

DTS: Only DTS can be played. ANLG: Only analog signal can be played.

Learning about input modes, jacks and Input Selection buttons CinemaStation can receive signals from the VIDEO 1 (analog), VIDEO 2 (analog), VCR (analog), MD/CD-R (analog), and OPTICAL (digital) jacks of connected equipment. You can assign a VIDEO 1, VIDEO 2, VCR or MD/CD-R input name to the OPTICAL IN jack. This will allow you to use the VIDEO 1, VIDEO 2, VCR or MD/CD-R button to input a device connected to the OPTICAL IN jack (MD/CD-R is assigned in the default setting.) Normally, an analog signal is input to the VIDEO 1, VIDEO 2, VCR or MD/CD-R IN jack, and a digital signal is input to the OPTICAL IN jack. However, by setting the input mode to AUTO the input will be automatically detected and you can then playback audio from the device you want by simply pressing an Input Selection button.

Advice

Notes

Input Selection buttons

Notes U.K. and Europe models only have VIDEO instead of VIDEO 1 and

VIDEO 2. VIDEO is used as VIDEO 1 in above models.

014DVX-S200-en 04.3.1, 11:20 AM78

79

Additional Features A

d d

itio n

al F eatu

res E

n g

lish

Using the Sleep Timer After a specified time the power automatically enters standby so you can enjoy CinemaStation until you fall asleep.

TV

CH

CINEMA

CH

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

ON SCREEN MENU

TEST

RETURNSTATUS

TV VOL VOLUME

MUTE

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

SET MENU

ENTER

SLEEP

You cannot link the sleep timer of the device that is playing, so make sure to set the sleep timer of each device separately. The Sleep Timer cancels if you press POWER on the Remote Control, press STANDBY/ON on CinemaStation or pull out the

power cord. Memory backup remembers the previous setting so you can use the same setting next time.

Play the source.

Repeatedly press SLEEP and set the time to enter standby mode. The CinemaStation Display changes as shown below.

Once the Sleep Timer is set a SLEEP indicator lights up in the CinemaStation Display.

SLEEP 120 min

SLEEP 90 min

SLEEP 60 min

SLEEP 30 min

SLEEP OFF

To cancel the Sleep Timer Keep pressing SLEEP until SLEEP OFF appears in the CinemaStation Display. In a few seconds SLEEP OFF disappears. The CinemaStation Display once again shows the DSP Program and the SLEEP indicator disappears.

Advice

015DVX-S200-en 04.3.1, 11:20 AM79

80

Additional Features

Enjoying High-Quality Video Progressive Scan (NTSC only)

The COMPONENT VIDEO jack on CinemaStation is compatible with Progressive Scan. You can enjoy highly defined images without flicker when connecting to a television that has a component video input jack compatible with Progressive Scan. Progressive Scan is available only for NTSC signal output. See pages 95 and 96, On Screen Menu Guide.

Before connecting make sure to turn off the television and CinemaStation power.

Connect the television. Use a commercially available component video cable.

Start playing the DVD. See page 10, Viewing a DVD.

Press PROGRESSIVE on CinemaStation.

Y PB PR

COMPONENT VIDEO (480p/480i) (DVD ONLY)

MONITOR OUT

IN OUT

DIGITAL AUDIO OPTICALSUBWOOFER

OUT SYSTEM

CONNECTOR

75 UNBAL

FM ANT

GND

AM ANTY

PB

PR

PROGRESSIVE

If you play video with a 4:3 aspect ratio on a 16:9 wide television screen, Progressive Scan may fill the screen top to bottom. In this case, use the On Screen Menu to change to the screen display that matches your television. See pages 95 and 96, On Screen Menu Guide. If you cannot adjust the size, turn off Progressive Scan. (Changes to interlace output.)

When Progressive Scan is on, a video signal will only output from the COMPONENT VIDEO. You can use the COMPONENT VIDEO jack and Progressive Scan only for DVD playback, so it is not possible to enjoy progressive playback from other sources.

CONSUMERS SHOULD NOTE THAT NOT ALL HIGH DEFINITION TELEVISION SETS ARE FULLY COMPATIBLE WITH THIS PRODUCT AND MAY CAUSE ARTIFACTS TO BE DISPLAYED IN THE PICTURE. IN CASE OF 525 PROGRESSIVE SCAN PICTURE PROBLEMS, IT IS RECOMMENDED THAT YOU SWITCH THE CONNECTION TO THE STANDARD DEFINITION OUTPUT. IF THERE ARE QUESTIONS REGARDING YOUR VIDEO MONITOR COMPATIBILITY WITH THIS UNIT, PLEASE CONTACT OUR CUSTOMER SERVICE CENTER. This unit is compatible with the complete line of YAMAHA projectors, including the DPX-1, LPX-500, DPX-1000 and with the YAMAHA PDM-1 plasma display.

Please...

Advice

The PROGRESSIVE indicator lights up.

To cancel Progressive Scan Press PROGRESSIVE to turn off the PROGRESSIVE indicator.

Note

015DVX-S200-en 04.3.1, 11:20 AM80

81

Additional Features A

d d

itio n

al F eatu

res E

n g

lish

Protecting Your Children from Undesirable Material Using Parental Control

You can cut a scene that you do not feel it is suitable for your children, or lock a disc from being played.

CinemaStation allows you to set the level of Parental Control. It then checks the level of a disc whose level has been set in advance and automatically decides if the content is suitable for viewing by your children before playing.

Setting the Password and Parental Control Level

TV

CH

CINEMA

CH

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

ON SCREEN MENU

TEST

RETURNSTATUS

TV VOL VOLUME

MUTE

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

SET MENU

ENTER

g

h

g g

ON SCREEN

The default password is 0000. If the password you input is wrong, some menu items, such as Parental level or Disc Lock, are grayed out. Enter the correct

password. If you forget your password, press s four times, instead of the Number buttons.

Advice

Press w to select Enter PIN, then press w.

Press w and h a number of times to select Access.

Press g to select Setup.

Press ON SCREEN.

Number

Number buttons

Program

View

Play Option

Search

Toolbar

Preferences

Setup

Access

TV

Language

Audio Menu

Features

Setup

Preferences

Toolbar

Disc lock

Parental level

Enter PIN

Change PIN

Access

TV

Language

* * * *

Disc lock

Parental level

Change PIN

Enter PIN

015DVX-S200-en 04.3.1, 11:20 AM81

82

Additional Features

TV

CHCH

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

ON SCREEN MENU

TEST

RETURNSTATUS

TV VOL VOLUME

MUTE

SET MENU

ENTER

g

h

g g

ON SCREEN

TV

CH

CINEMA

CH

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

ON SCREEN MENU

TEST

RETURNSTATUS

TV VOL VOLUME

MUTE

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

SET MENU

ENTER

g

h

g g

ON SCREEN

Perform steps 1 to 5 in Setting the Password and Parental Control Level on page 81.

Enter the new password (4 digits) again for confirmation.

Enter the new password (4 digits) with the Number buttons.

Enter the current password (4 digits) with the Number buttons.

Press g to select Change PIN, then press w.Number buttons

Change the password

Press ON SCREEN to turn off the On Screen Menu.

Press w or q and select control level (0 to 8). 0: Parental Control is set to off, and you can play all discs. 1 to 7: You can play discs of same level or below the level you set. The smaller the number the stricter Parental Control is. 8: You can play all discs.

Press h and select Parental level.

Use the Number buttons to enter a password (4 digits).

Number buttons

* * * *Enter PIN

Disc lock

Parental level

Change PIN

0

Enter PIN

Parental level

Disc lock

Change PIN

+3

Enter PIN

Parental level

Disc lock

Change PIN

Press ON SCREEN to turn off the On Screen Menu.

015DVX-S200-en 04.3.1, 11:20 AM82

83

Additional Features A

d d

itio n

al F eatu

res E

n g

lish

The identification data of a disc that is played when the disc lock is on is stored in CinemaStations memory. The next time the disc is played the restriction method selected previously is applied. If you select Play once, the next time the disc is played the selection window will appear. However, if you select Play always, the next time the disc is played the selection window will not appear. After

appears on the screen, press s within about 10 seconds.

The memory can only store identification data for up to 120 discs. If you play the 121st disc, the identification data of the first disc (oldest) will be erased from memory.

Locking a Disc

TV

CH

CINEMA

CH

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

ON SCREEN MENU

TEST

RETURNSTATUS

TV VOL VOLUME

MUTE

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

SET MENU

ENTER

g

h

g g

ON SCREEN

When you are finished with the setting press the ON SCREEN key and the On Screen Menu will close.

As long as a password is not entered playback will not be possible. Select Off if you do not want to lock.

After pressing the w key, press the h key and select On.

Press the h key a number of times and select the disc lock.

Disc lock is a function that restricts the playback of a video disc. Setting the disc lock to on enables the lock and disables disc playback. However, each time a disc is inserted, it is possible to play it by selecting a playback restriction method Play once or Play always, then entering your password.

Number buttons

Off

Parental level

Disc lock

Enter PIN

OnDisc lock

Parental level

Enter PIN

Off

Advice

Perform steps 1 to 5 in Setting the password and Parental Control Level (Page 81).

Insert a disc. A selection window with Play once and Play always will appear on the TV screen.

After pressing the w key enter a password using the number keys. Playback starts.

Use the h key or g key to select Play once or Play always.

How to enter a password and begin playback

015DVX-S200-en 04.3.1, 11:20 AM83

84

Operating Other Equipment with the CinemaStation Remote Control

Storing Manufacturer Codes in the Remote Control

If you set the manufacturer code (a unique code assigned to each manufacturer) in the CinemaStation Remote Control, you can operate a connected television, VCR, CD or MD recorder with the Remote Control.

Depending on the model, the Remote Control may not work, or only work with a limited number of functions. In this case, use the remote control that came with the television, VCR, CD or MD recorder.

Setting the Manufacturer Code

When a manufacturer code is set for the TV button, VCR button or MD/CD-R button, you can begin using the features described in Available Operations on page 85.

TV

CH

CINEMA

CH

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

ON SCREEN MENU

TEST

RETURNSTATUS

TV VOL VOLUME

MUTE

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

SET MENU

ENTER

TV

SHIFT

VCR

MD/CD-R

Make sure that you set the correct manufacturer code. With a manufacturer code set for the TV button, press the button to turn the TV power on/off (standby), and check that the setting is working correctly. With a manufacturer code set for the VCR button or the MD/CD-R button, press the button then the features described in Available Operations on page 85, and check that the setting is working correctly.

The TV button has 299, the VCR button has 399 and the MD/CD-R button has 499 as the factory default setting for manufacturer code.

While holding down SHIFT, enter the manufacturer code (3 digits) of the device with the Number buttons. For details, refer to Manufacturer Code List on pages 87 and 88. When the setting succeeds, Code Set OK appears; however, when it does not, Code Set NG appears in the CinemaStation Display. If setting is unsuccessful, perform steps 1 and 2 again. When finished entering the code, release your finger from SHIFT.

Perform steps 1 to 2 while holding down SHIFT.

While holding down SHIFT, press TV, VCR or MD/ CD-R. Each button can be assigned one manufacturer code.

For the TV button you can only set a television manufacturer code and for the VCR button or MD/CD-R button you can only set a VCR, CD or MD recorder manufacturer code.

Number buttons

016DVX-S200-en 04.3.1, 11:21 AM84

85

Operating Other Equipment with the CinemaStation Remote Control O

p eratin

g O

th er E

q u

ip m

en t

w ith

th e C

in em

aS tatio

n R

em o

te C o

n tr o

l E

n g

lish

Available Operations

While you set the manufacturer code for the TV, MD/CD-R or VCR button, you can use the following functions after you press the TV, MD/CD-R or VCR button.

TV

CH

CINEMA

CH

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

ON SCREEN MENU

TEST

RETURNSTATUS

TV VOL VOLUME

MUTE

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

SET MENU

ENTER

When the Remote Controls TV, VCR or MD/ CD-R button does not work even after setting the device manufacturer code

Try again from step 1 and keep the following points in mind. Make sure you select the Remote Controls TV, VCR

or MD/CD-R button correctly when setting the manufacturer code.

If there are multiple manufacturer codes enter them in order.

After reinserting batteries, try the steps again (within 2 minutes of reinserting). (When reinserting batteries be careful not to press the Remote Control buttons. If a manufacturer code has been set for the TV, VCR or MD/CD-R button, it may get deleted.)

To return to the factory default settings

While pressing SHIFT down as in step 2 Setting the Manufacturer Code, enter 299 for TV, 399 for VCR and 499 for MD/CD-R. (Step 3 is not necessary.)

Maintaining manufacturer code settings

Replace batteries before they become unusable. When the batteries wear out and you remove them, the custom manufacturer code setting will stay in memory for about 2 minutes. Be careful because if more than 2 minutes elapse the codes may be deleted. Also, at this time, be careful not to accidentally press a Remote Control button. This can delete the codes.

*1TV POWER

*1TV Input Switch

Stop

Fast Forward

Pause

Playback

Video Channel Selection (+)

Press VCR or MD/CD-R before starting operations.

*1TV Channel Selection (+)

*1TV Channel Selection (-)

Rewind

Video Channel Selection (-)

*1TV Volume (+)

*1TV Volume (-)

VCR operation

*1While you set the TV manufacturer code for the TV button, you can operate your television.

016DVX-S200-en 04.3.1, 1:09 PM85

86

Operating Other Equipment with the CinemaStation Remote Control

TV

CH

CINEMA

CH

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

ON SCREEN MENU

TEST

RETURNSTATUS

TV VOL VOLUME

MUTE

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

SET MENU

ENTER

TV

CH

CINEMA

CH

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

ON SCREEN MENU

TEST

RETURNSTATUS

TV VOL VOLUME

MUTE

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

SET MENU

ENTER

TV operation

CD or MD recorder operation

Press POWER before starting operations.

Channel Selection (+)

Channel Selection (-)

*2VCR Rewind

Input Switch

Volume (+)

Volume (-)

*2VCR Stop

*2VCR Fast Forward

*2VCR Pause

*2VCR Playback

Track Selection/Elapsed Time Input

StopPause

Playback

Reverse Search

Reverse Skip

Forward Search

Forward Skip

Press MD/CD-R or VCR before starting operations.

*2While you set the VCR manufacturer code for the VCR button or the MD/CD-R button, you can operate your VCR.

016DVX-S200-en 04.3.1, 11:21 AM86

87

Operating Other Equipment with the CinemaStation Remote Control O

p eratin

g O

th er E

q u

ip m

en t

w ith

th e C

in em

aS tatio

n R

em o

te C o

n tr o

l E

n g

lish

Manufacturer Code List

Depending on the model and year, you may not be able to use some manufacturer products. In this case, use the remote control supplied with each product.

Manufacturer Manufacturer Code

Yamaha 299/292

Admiral 292/293

Aiko 287

Aiwa 294/276/283

Akai 295/296

Alba 296

AOC 297/286

Audiovox 285

Belcor 297

Bell & Howell 292

Bestar 298

Blaupunkt 229/222

Blue sky 298

Bradford 285

Brandt 223

Brocsonic 297

Brokwood 297

Bush 296

Candle 286/297

Citizen 286/287/297

Clatronic 298

Contec 285

Craig 224/285

Croslex 225

Crown 285

Curtis Mathis 297/226/286

CXC 285

Daewoo 297/298/224/227/228/ 287

Daytron 239/297

Dual 298

Dumont 297

Emerson 297/224/239/232/285

Envision 286/297

Ferguson 223/265/266

First line 298

Fisher 295/233

Fraba 298

Manufacturer Manufacturer Code

Funai 277/278/285

Futuretec 285

GE 293/297/234/235/236

Gibralter 297

LG/Goldstar 297/298/239/237

Goodmans 296/298/223

Grundig 229/238/249

Harvard 285

Hitachi 297/239/242/243

ICE 296

Irradio 296

Itt/Nokia 244/245

JC Penny 293/297/234/237/286

JVC (Victor) 296/246/247

Kendo 298

Kenwood 297

KTV 297/239/285

Loewe 298/248

LXI 293/297/225/226/233

Magnavox 297/225/239/286

Marantz 286/297

Matsui 295

MGA 286/297

Mitsubishi 299/297/259

MTC 286/297

Multitec 285

NEC 297/252/282/286

Nikko 286/287/297

Nokia 244/245

Nokia Oceanic 245

Nordmende 265/266

NTC 287

Onwa 296/285

Panasonic 234/235/236/253

Philco 297/225/239/286

Philips 225

Pilot 297

Pioneer 226/235/254/255/268

Manufacturer Manufacturer Code

Portland 297/256/287

Quasar 234/235

Radio Shack 299/293/297/285/286

RCA 293/297/234/256/257/ 258

Realistic 299/293/297/285/286

SABA 223/269/265/266

Sampo 286/297

Samsung 297/239/248/262/275/ 286

Sanyo 295/233/279/272/273/ 274

Schneider 296

Scott 297/285

Sharp 292/239/232/284

Shogun 297

Siemens 229

Signature 292

Sony 263

Soundesign 285

SSS 285/297

Starlite 285

Sylvania 297/225/286

Teknika 297/285/287

Telefunken 269/264/265/266

Thomson 223/266

Toshiba 292/226/267

Videch 297/242

Wards 297/239/232/286

TV

016DVX-S200-en 04.3.1, 11:21 AM87

88

Operating Other Equipment with the CinemaStation Remote Control

Manufacturer Manufacturer Code

Yamaha 399/392/393/394

Admiral 395

Aiwa 396/397/398/329/339

Akai 322/323/324

Asha 363

Audio Dynamic 392/394

Audiovox 396

Beaumark 363

Bell & Howell 393

Blaupunkt 325/326

Brocsonic 327

Bush 322

Calix 396

Candle 335/363/396

Canon 325/328

CGM 396/332

Citizen 396

Craig 396/363

Curtis Mathis 397/328/333/392

Cybernex 363

Daewoo 328/334/335

DBX 392/394

Dimensia 333

Dynatech 397

Electrohome 396

Electrophonic 396

Emerson 327/334/396/397

Fisher 393/336

Funai 397

Garrard 397

GE 328/333/387/363

LG/Goldstar 396/388/392

Goodmans 334/337

Grandiente 397

Grundig 332/338

Hitachi 325/333/349/342/343

Harman Kardon 392

Instant Replay 325/328

Itt/Nokia 393

JCL 328

JC Penny 392/393/394/328/333/ 349/363/396

JVC (Victor) 392/394/344/345/346/ 347

Kendo 396

Kenwood 392/394/396

Kodak 396

Manufacturer Manufacturer Code

Lloyd 397

Loewe 396/337

Luxor 395

LXI 393/396/397/336/349

Magnavox 325/326/328

Magnin 363

Marantz 392/394/328

Marta 396

Matsui 396

MEI 328

Memorex 328/336/363/396/397

Minolta 333/349/342

Mitsubishi 399/344/348/359/352/ 353

MTC 363/397

Multitech 397/348/354

NEC 392/394/344/383

Nikko 396

Noblex 363

Nokia 393/395

Nokia Oceanic 395

Okano 323

Olympic 325/328

Optimus 396

Orion 327

Panasonic 325/328/355/378/384/ 385

Pentax 333/349/342

Philco 325/328

Philips 325/326/328/337/356/ 357

Phonola 337

Pilot 396

Pioneer 325

Quasar 325/328

Radio Shack 396/397

Radix 396

RCA/PROSCAN 325/326/328/333/335/ 349/358/369/363/342

Realistic 393/397/328/336/359/ 362/396

Samsung 354/358/363/364/365/ 366/335

Sansui 394

Sanyo 393/336/367/363

Schneider 337

Scott 399/335/336/348/359/ 352/354/358

Sears 328/342/396

Seleco 322

Manufacturer Manufacturer Code

Sharp 395/362/382

Siemens 393

Signature 2000 395/397

Sony 368/379/372/373/374/ 375

Sylvania 397/325/326/328

Symphonic 397

Tandberg 334

Tashiro 396

Tatung 392/394

Teac 392/394/397

Technics 325/328

Teknika 328/396/397

Telefunken 376/377

Thorn 393/396

Toshiba 335/369/389

Totevision 363/396

Universum 396/327/376

Vector Research 392

Videosonic 363

W.WHouse 396

Wards 395/396/336/362/328/ 342/363/397

CD recorder Manufacturer Manufacturer Code

Yamaha 499

DENON 422/423

Hitachi 424

JVC (Victor) 425/428

Kenwood 422

Marantz 422

Philips 422

Pioneer 426

Sony 427

Teac 429

MD recorder Manufacturer Manufacturer Code

Yamaha 599/522/598

Denon 523/524

JVC (Victor) 525

Kenwood 526

Onkyo 592

Pioneer 527

Sharp 528

Sony 522

Teac 593

VCR

016DVX-S200-en 04.3.1, 11:21 AM88

89

Using the SET MENU U

sin g

th e S

E T

M E

N U

E n

g lish

Using the SET MENU

Even during playback you can change settings in the SET MENU. To learn more about * Speaker Set read Setting the Speaker Mode on page 63.

You can use the SET MENU to adjust settings, including Speaker settings. Change the settings to match your listening environment.

SET MENU List

The SET MENU contains the items below.

Advice

Item Default Setting (value)

* Speaker Set

* CENTER SML

* FRONT SML

* SUR. SML

* BASS SWFR

* F. Level Nrm

* LFE Level

* SP LFE 0 dB

* HP LFE 0 dB

* SP Delay

* CENTER 0 ms

* SA-CD Delay

* CENTER 0 ms

* SUR. 0 ms

* D. Range

* SP D.R MAX

* HP D.R MAX

* L/R Balance Center

* HP Tone CTRL

* HP BASS 0 dB

* HP TRBL 0 dB

* Input Assign

* OPT: MD/CD-R

* Input Mode

* MODE: AUTO

* Display set

* DIMMER 0

* Tuner Step AM9/FM50 (Asia, Korea and General models only)

017DVX-S200-en 04.3.1, 11:21 AM89

90

Using the SET MENU

Navigating the SET MENU

TV

CH

CINEMA

CH

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

ON SCREEN MENU

TEST

RETURNSTATUS

TV VOL VOLUME

MUTE

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

SET MENU

ENTER

AMP

SET MENU

g

h

g g

Press AMP.

Press SET MENU.

Press h or g repeatedly to select the Menu you want.

Press q or w. Once in the setting mode of the selected menu the current setting appears in the CinemaStation Display. Depending on the item, press h or g to enter a submenu.

Press q or w repeatedly to change the setting.

When exiting the SET MENU, press SET MENU. Pressing any one of DSP Program buttons also exits the SET MENU.

017DVX-S200-en 04.3.1, 11:22 AM90

91

Using the SET MENU U

sin g

th e S

E T

M E

N U

E n

g lish

Adjust the playback level of the LFE signal (* LFE Level)

You can adjust the LFE channel output level while playing a Dolby Digital or DTS signal. Adjust the LFE level to match the performance of the Subwoofer and headphones.

Submenu: SP LFE, HP LFE Variable range (dB): -20 to 0 dB. Default setting: 0 dB

L C

C

R

RL RR

Virtual Center Speaker Position

Set the Delay Time of the Center Speaker (* SP Delay)

You can set the Delay Time of the Center Speaker. This is effective when the Center Speaker outputs sound during Dolby Digital, DTS and other forms of playback.

Normally the Center Speaker and Front L/R Speakers are placed in line with each other. However, they should be placed at an equal distance from the listener so that the sound each one outputs enters the listeners ear at the same time. With Delay Time, the Center Speaker can be moved to an ideal position further away to match the distance of each speaker to the listener. Center Delay is effective in adding depth to the sound field and presence to speech.

Variable range (ms): 0 to 5 ms Default setting: 0 ms

Press w to set the speakers virtual position further away. Press q to set it closer.

Every 1 ms increase in Delay Time increases the distance away from the listening position by 30 cm (1 foot).

Advice

Set the Delay Time of the Center and Surround Speakers during Super Audio CD playback (* SA-CD Delay)

You can set the Delay Time of the Center and Surround Speakers when playing Super Audio CDs containing front-channel sound or surround-channel sound.

Normally the Center Speaker and Front L/R Speakers are placed in line with each other and the Surround Speakers are placed behind the listener. For best results place them at an equal distance from the listener so that the sound each one outputs enters the listeners ear at the same time. Use Delay Time to move the virtual position of the Center Speaker or the Surround Speakers to an ideal position further away to match the distance of each speaker to the listener. Center Delay and Surround Delay add depth to instrument sound and create the expansive feeling of a concert hall.

Submenu: CENTER, SUR. Variable range: CENTER 0 to 5 ms, SUR. 0 to 15 ms

Press w to set the speakers virtual position further away. Press q to set it closer.

Every 1 ms increase in Delay Time increases the distance away from the listening position by 30 cm (1 foot).

L C

C

R

LS RS

LS RS

Virtual Center Speaker Position

Virtual Surround Speakers Position

Advice

017DVX-S200-en 04.3.1, 11:22 AM91

92

Using the SET MENU

Reassign input jacks (* Input Assign)

You can assign CinemaStations OPTICAL IN jack to VIDEO 1, VIDEO 2, VCR or MD/CD-R. When the source is set to one of them, press the appropriate input selection button to operate the device connected to the OPTICAL IN jack and the input source name appears on the display panel based on your selection.

Selection items: MD/CD-R, VIDEO 1, VIDEO 2, VCR Default setting: MD/CD-R

U.K. and Europe models only have VIDEO instead of VIDEO 1 and VIDEO 2.

VIDEO is used as VIDEO 1 in above models.

Set the input mode when powering on (* Input Mode)

Set the input mode for powering on when playback devices are connected to both digital and analog jacks.

Selection items: AUTO, LAST Default setting: AUTO

AUTO: When CinemaStation power is turned on the input mode automatically sets to AUTO. LAST: The last selected input mode is applied as is.

Adjust the CinemaStation Display brightness (* Display set)

Dimmer You can adjust the CinemaStation Display brightness.

Variable range: -4 to 0 Default setting: 0

Press w to increase the brightness. Press q to decrease the brightness.

Set frequency step (* Tuner Step) (Asia, Korea and General models only)

The inter-station frequency spacing differs depending on the areas. Set the frequency step according to the frequency spacing in your area.

Selection items: AM9/FM50, AM10/FM100 Default setting: AM9/FM50

Press w or q to select the desired setting.

Turn off CinemaStation after you change the setting. The new setting becomes effective after you turn on CinemaStation again.

Refer to the list below for the frequency spacing. North, Central and South America: AM10/FM100 Other areas: AM9/FM50

Notes

Set the dynamic range during Dolby Digital playback (* D. Range)

You can select the dynamic range (spread between the max. and min. volume) of Dolby Digital playback from 3 levels.

Submenu: SP D.R, HP D.R Selection items: MAX (Maximum), STD (Standard), MIN (Minimum) Default setting: MAX

MAX: Plays back the dynamic range of the source at the maximum limit. STD: Dynamic range recommended by software manufacturers for home use. MIN: Easy to hear even at a low volume, dynamic range suitable for evening listening.

Depending on the Dolby Digital playback source, the MIN dynamic range may not work and result in an extremely low volume. In this case, set the dynamic range to MAX or STD.

Adjust the volume balance of the Front Speakers (* L/R Balance)

You can set the volume balance of the Front L/R Speakers. This setting also applies to Headphones.

Variable range: L/R 10 levels Default setting: Center

Press w to make the sound smaller in the Front Left Speaker, and press q to make the sound smaller in the Front Right Speaker. You cannot turn off the sound for either one of the Front Speaker.

Adjust the sound quality of headphones (* HP Tone CTRL)

You can adjust the low tones (BASS) and high tones (TRBL) of your headphones.

Submenu: HP BASS, HP TRBL Variable range (dB): -6 to +3 dB. Default setting: 0 dB

Press w to increase the range of the low or high tones. Press q to decrease the range.

Note

Notes

017DVX-S200-en 04.3.1, 11:22 AM92

93

Using the On Screen Menu U

sin g

th e O

n S

creen M

en u

E n

g lish

Using the On Screen Menu You can use the On Screen Menu to adjust settings for DVD playback, including picture and language settings.

Navigating the On Screen Menu

For example, adjust the color saturation.

TV

CH

CINEMA

CH

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

ON SCREEN MENU

TEST

RETURNSTATUS

TV VOL VOLUME

MUTE

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

SET MENU

ENTER

ON SCREEN

g

h

g g

Press w to enter the submenus.

Press h or g to select Preference in the Main Menu.

Press ON SCREEN.

Program

View

Play Option

Search

Toolbar

Preferences

Setup

Features

PicturePreferences

Toolbar

Setup

Saturation

Contrast

Color settings

Brightness

Sharpness

Picture

Features

To select other items in the submenu, press w first, and press h or g.

Advice

018DVX-S200-en 04.3.1, 11:22 AM93

94

Using the On Screen Menu

TV

CH

CINEMA

CH

POWER POWER

AUDIO

/DTS SELECT

NIGHT SW

TV CH

TV INPUT

SLEEP

PRESET PRESET

A B C D E

CENTER SURR

SHIFT

STEREOMATRIX 6.1 A-BREPEAT

ANGLE SUBTITLE

DVR-S200 WB56620

ON SCREEN MENU

TEST

RETURNSTATUS

TV VOL VOLUME

MUTE

AMP

DVD/CD VCR VIDEO 1

VIDEO 2TUNERMD/CD-R

MOVIE MUSIC SPORTS GAME

SET MENU

ENTER

g

hON SCREEN

ENTER

g g

Press ENTER, then press ON SCREEN to turn off the On Screen Menu.

In some cases, you can also use h or g for setting content.

Press q or w to set.

Press h or g to select Saturation.

Press w to enter menu items.

Natural

Brightness

Color settings

Saturation

Contrast

Sharpness

0

Contrast

Saturation

Video shift

Color settings

+2

Contrast

Saturation

Video shift

Color settings

Advice

To set the other menu items, follow the example above.

018DVX-S200-en 04.3.1, 11:22 AM94

95

Using the On Screen Menu U

sin g

th e O

n S

creen M

en u

E n

g lish

On Screen Menu Guide

Set to On to turn on/off the status display using the STATUS button on the Remote Control. The status display includes the type of disc, the currently playing track/chapter number, the total time of track/chapter and the elapsed time of track/chapter. Set to Off to hide the status display.

Adjust from +1 to +7. Adjusts the screen position. The screen display moves to the right as the number becomes larger.

Adjust from -7 to +7. Adjusts the video color saturation.

Adjust from -7 to +7. Accentuates bright and dark parts of video.

Adjust the video shade.

Adjust from -7 to +7. Adjusts the video brightness.

Adjust from -7 to +7. Adjusts the video vividness.

Deletes all Program content. Page 33

Saturation

Picture

Preference

Toolbar

Features

Program

View

Contrast

Brightness

Sharpness

Status window

Clear All Tracks Program Play list (Playlist) Zoom

Angle Chapter Preview

Play Option

Setting ContentSetting ItemSubmenuMain Menu

Selects a track. Page 31

Selects Program Play On/Off. Page 33

Shows Playlist. Page 33

Enlarges the picture. Move + to the point to be enlarged using h, g, q, and w. Each time you press the ENTER key, the zoom changes. To return it to the previous size, select Zoom 1 and press ON SCREEN.

Switches the picture angle.

When this item is on, the beginning of each chapter can be previewed one by one.

Selects the audio language.

Select the title, chapter or track to play.

Selects the subtitle language. You can only select languages the disc contains.

Advances/reverses one frame at a time. Frame Advance is not available with video CD.

Select the speed from among -8, -4, 1, 4, 8.

Specify an elapsed time and search for a scene. Page 30

Select the speed from among -1, -1/2, -1/4, -1/8, 0, 1/8, 1/4, 1/2, 1.

Audio

Search

Disc Navigation

Sub-title (Subtitle)

Frame by Frame

Video shift

Color settings (Colour settings)

Fast Time

Slow

018DVX-S200-en 04.3.1, 11:22 AM95

96

Using the On Screen Menu

Set the Disc Lock On/Off. Page 83

Adjust the level from 0 to +8. Page 82

Enter the password. Page 81

Change the password. Page 82

Set to match your TV screen aspect.

4:3 panscan

4:3 letterbox

Wide-screen (Widescreen)

Set the video signal system*2 to match your TV. Set to AUTO when using a TV compatible with both NTSC and PAL.

(U.K. and Europe models only) Sets the output signal of AV MONITOR OUT jack to YUV or RGB.

Set the language you usually select for subtitles. When playing a disc, the subtitles in the selected language appear first. When the disc does not contain the selected subtitle language, the subtitle of that language will not appear.

Disc Lock Parental level Enter PIN Change PIN TV shape

Access

TV*1

Setup

TV System

Video Output

Language

Setting ContentSetting ItemSubmenuMain Menu

Default Sub-title (Default Subtitle)

Select the country where you use CinemaStation.

Set the language for the On Screen Menu.

Set the language you usually select for audio.

Country Menu Language

When playing a disc, you hear the audio in the selected language first. When the disc does not contain the selected language you selected, it will play in another language.

Select the output signal for the OPTICAL OUT jack. The speaker sound changes depending on the setting for this menu item. All: Outputs all types of digital signals that CinemaStation can reproduce. PCM Only: Outputs the Pro Logic decoded signal only.

Set Playback Control On/Off. If set to Off, the Disc Menu does not appear on the TV screen.

Default Audio

Features PBC

*1 Be careful when setting this menu item. If it does not match your TV, the menu and playback screen will not appear properly or will not appear on the TV. If that happens, refer to Recover TV settings below.

*2 This unit can play PAL and NTSC, but your television must match the system used on the disc.

Recover TV settings When the screen does not appear properly due to TV setting, perform the steps below to recover the setting.

1 Press DVD/CD.

2 Press s for 5 seconds. NTSC<->PAL appears in the CinemaStation Display.

3 Press e to switch the setting. NTSC/PAL SET appears in the CinemaStation Display.

When connecting with AV MONITOR OUT (U.K. and Europe models only)

1 Perform steps 1 and 2 above.

2 Press s again. YUV<->RGB appears in the CinemaStation Display.

3 Press e to switch the setting. YUV/RGB SET appears in the CinemaStation Display.

Audio Menu Digital output

018DVX-S200-en 04.3.1, 11:22 AM96

97

Appendix A

p p

en d

ix E

n g

lish

Solutions to Common Problems Be sure to check the points below if CinemaStation doesnt seem to be working normally for you. If you notice something wrong that is not listed below and you have already tried some solutions with no success, turn off the CinemaStation power, remove the power plug from the outlet and contact the store where you purchased the product or your nearest YAMAHA sound products service center and ask for assistance.

General Problems

Power turns on but immediately shuts off.

1 The power plug is not completely plugged in.

Insert the plug into the outlet firmly.

2 Speaker cable is shorted. When power is turned on, the protective circuit engages and shuts the system down.

Make sure that all speaker cables are correctly connected.

3 CinemaStation received a strong, external electric shock such as from a lightening bolt or excessive static electricity.

Put CinemaStation in standby, pull out the electric cord then wait for about 30 seconds before reinserting the cord and turning on the power again.

4 The system cable is not connected properly.

Connect the system cable securely.

No sound.

1 You did not connect the cable properly.

Check your connections.

2 The source you selected is not suitable for playback.

Choose the correct source using the Input Selection buttons.

3 You did not connect the Speaker cable properly.

Check your speaker connections.

4 You turned the sound volume down.

Turn the sound volume up.

5 Sound is muted.

Press MUTE or VOLUME +/- to regain the sound and adjust the volume to your liking.

6 You inserted a CD-ROM that CinemaStation cannot play.

Play a source signal that CinemaStation can play.

No picture.

You did not connect the cable properly.

Check your connections.

The audio suddenly decreased.

The Sleep Time function started working.

Turn the power back on and try playing the source again.

Sound is too low on one side.

You did not connect the cable properly.

Check your connections.

Cause

Solution

Cause

Solution

Cause

Solution

Cause Solution

Cause

Solution

Cause

Solution

Cause

Solution

Cause

Solution

Cause

Solution

Cause

Solution

Cause

Solution

Cause

Solution

Cause

Solution

019DVX-S200-en 04.3.1, 11:23 AM97

98

Appendix

No sound except from the Front Speakers.

1 You are listening to STEREO sound.

Press STEREO and make sure sound field effect is on.

2 You are playing a source such as Dolby Surround, Dolby Digital or DTS that doesnt contain a special effect signal.

Select another DSP Program.

3 A digital audio sampling frequency over 48 kHz is input. A digital audio sampling frequency over 48 kHz only outputs from the Front Speakers.

No sound from the Center Speaker.

1 You turned off the Center Speaker volume level.

Turn up the Center Speaker volume. See page 61.

2 You set * CENTER in the SET MENU to NON.

Set the Center Speaker correctly. See page 64.

3 You have selected a DSP Program from the Music group (excluding 5ch Stereo).

Select another DSP Program. See pages 16 and 17.

4 Dolby Digital and DTS sources do not contain a center channel signal.

No sound from the Surround Speakers.

1 You turned off the Surround Speaker volume level.

Turn up the Surround Speaker volume. See page 61.

2 CinemaStation plays a monaural source in the Theater DSP Program.

Select another DSP Program. See pages 16 and 17.

No sound from the Subwoofer.

1 You set * BASS in the SET MENU to FRONT when CinemaStation plays a Dolby Digital or DTS source.

Set * BASS to SWFR or BOTH. See page 64.

2 You set * BASS in the SET MENU to FRONT or SWFR when CinemaStation plays a 2-channel source.

Set * BASS to BOTH. See page 64.

3 The source doesnt contain an LFE or other low tone signal (below 90 Hz).

No low tones.

The Speaker mode you selected in the SET MENU does not match your speaker.

Set the appropriate Speaker mode based on the size of the speakers you are using. See page 63.

Strange humming noises.

You did not connect the pin cable properly.

Check your pin cable connections.

Cause

Solution

Cause

Solution

Cause

Cause

Solution

Cause

Solution

Cause

Solution

Cause

Cause

Solution

Cause

Solution

Cause

Solution

Cause

Solution

Cause

Cause

Solution

Cause

Solution

019DVX-S200-en 04.3.1, 11:23 AM98

99

Appendix A

p p

en d

ix E

n g

lish

Sound volume will not increase.

The power of the device connected to CinemaStations output jack is not turned on.

If the power of the device connected to the output jack is not turned on, playback may be distorted and volume low. Turn on the power of the connected device.

Sound field effect cannot be recorded.

It is not possible to record audio enhanced by a sound field effect.

Audio recording will not work.

1 You are trying to make a digital recording with an analog source.

Try inputting a digital source.

2 CinemaStation and the recording device are not connected digitally.

Connect them digitally.

3 You are trying to make an analog recording with a digital source.

Try inputting an analog source.

4 CinemaStation, the playback device and the recording device do not share an analog connection.

Connect them with an analog connection.

5 Some recording devices are not able to record a digital source such as Dolby Digital or DTS.

CinemaStation is not working normally.

The internal microcomputer froze up due to electric shock (lightening bolt or excessive static electricity) or drop in power supply.

Pull out the AC plug from the outlet and after about 30 seconds plug it in again.

Digital and high frequency devices create noise.

CinemaStation is placed too close to a digital or high frequency device.

Place CinemaStation further away from such devices.

SET MENU setting content has disappeared.

The power cord has not been connected to the outlet for over a week or the time set for the external timer has past, which turned off the power, more than a week ago.

Set the SET MENU again.

Cause

Solution

Cause

Cause

Solution

Cause

Solution

Cause

Solution

Cause

Solution

Cause

Cause

Solution

Cause

Solution

Cause

Solution

019DVX-S200-en 04.3.1, 11:23 AM99

100

Appendix

Disc Playback

One of the buttons doesnt work.

Some discs do not allow certain operations.

Playback does not start when pressing w, or it immediately stops.

1 When moved from a very cold place to a warm one, condensation forms on the lens.

Do not use for 1 to 2 hours.

2 You inserted a disc that CinemaStation cannot play.

3 The disc is dirty.

Wipe the disc clean.

4 The disc is not set in the tray correctly.

Set the disc in the tray correctly. See page 11.

Audio or subtitle language does not switch.

1 The disc does not contain multiple audio or subtitle languages.

2 Use the Disc Menu to change audio or subtitle languages. See page 36.

No subtitles appear.

1 DVD does not contain subtitle data.

2 The subtitle setting is off.

Turn on subtitles. See page 13.

3 When using A-B Repeat subtitles sometimes do not appear before and after points A and B.

Viewing angle does not change.

You can only use this feature if you are playing a disc recorded with multiple angles.

VCR recording does not work.

Almost all DVD discs are copy protected, so you cannot copy them.

Picture looks poor while fast forwarding or reversing.

To some degree the picture does not look normal, but this is not a defect.

The television (monitor) has no picture. (Or the screen size looks strange.)

1 The setting in the On Screen Menu is not correct.

Select Setup TV in the On Screen Menu to set the menu item correctly.

2 The television cannot handle progressive input.

Turn off CinemaStations progressive output and change to interlace input on the television. See page 80.

Part of picture appears double with progressive output.

The disc content does not match the progressive output due to the editing method or other conditions.

Turn off CinemaStations progressive output and change to interlace input on the television (monitor). See page 80.

The picture quality is poor.

Adjust the picture quality using Picture in the On Screen Menu. See page 95.

No Status display appears.

Under Features in the On Screen Menu, switch the Status window to On. See page 95.

Cause

Cause

Solution

Cause

Cause Solution

Cause

Solution

Cause

Cause

Cause

Cause

Cause

Cause

Cause

Cause

Cause

Solution

Cause

Solution

Cause

Solution

Solution

Solution

Solution

019DVX-S200-en 04.3.1, 11:24 AM100

101

Appendix A

p p

en d

ix E

n g

lish

The disc is ejected as soon as it is inserted.

A disc that cannot be played has been inserted.

Radio Reception

Preset Tuning does not work.

1 The Preset (memory) has been deleted.

Perform the Preset operation again. See page 41.

Too much noise blocks out stereo broadcast.

The radio station is far away from your area or your antenna is weak.

1 Check your antenna connection. And change your outdoor FM antenna for a multi- channel one.

2 Try Manual Tuning. See page 40.

Audio is distorted and the receiver sensitivity is poor even with outdoor FM antenna.

You are experiencing multipath reflection and other radio interference.

Change the antennas height, direction or placement.

Auto Tuning does not work.

The radio station is far away from your area or your antenna is weak.

1 Try Manual Tuning. See page 40.

2 Change your outdoor FM antenna for a multi-channel one.

Auto Tuning does not work.

The radio waves are weak or your antenna is not completely connected.

1 Change the AM Loop antennas direction. See page 38.

2 Try Manual Tuning. See page 40.

Too much noise.

Noise can be related to atmospheric electricity and lightning, or fluorescent lights, motors and thermostats attached to electric devices.

Connecting the outdoor AM antenna and establishing good grounding will decrease noise. However, it is difficult to completely eliminate noise.

Too much noise, especially in the evening.

A television is in use near CinemaStation.

Place the television further away from CinemaStation.

Cause Cause

Solution

FM/AM

Cause

Solution

FM

Cause

Solution

Solution

Cause

Solution

Cause

Solution

Solution

AM

Cause

Solution

Solution

Cause

Solution

Cause

Solution

No Disc appears in the CinemaStation Display.

No disc is inserted or a disc is inserted incorrectly.

Set the disc in the tray correctly. See page 11.

019DVX-S200-en 04.3.1, 11:24 AM101

102

Appendix

The Remote Control does not work.

1 You are outside the Remote Control operating range.

Operate the Remote Control within 6 m (20 feet) and a 30 angle of the Remote Control Sensor.

2 The Remote Control Sensor is exposed to direct sunlight or lighting (inverted fluorescent lamps).

Change the lighting or CinemaStations orientation.

3 The batteries are worn out.

Replace the batteries with new ones.

4 You did not select the device to operate.

Press the Input Selection buttons to select the device you want to operate.

Remote Control does not work with CinemaStation.

You did not select the mode to operate CinemaStation.

Press DVD/CD, AMP or TUNER on the Remote Control before starting operation.

Remote Control

A peripheral device does not work with the Remote Control.

1 You cannot operate a system component.

Use the remote control that came with the device to operate it.

2 You did not correctly set the manufacturer code.

Set the manufacturer code once again. See page 84.

Set a different code from the list of codes for the same manufacturer. See pages 87 and 88.

3 The Remote Control is not compatible with your equipment.

Use the remote control that came with the device to operate it.

Cause

Solution

Cause

Solution

Cause

Solution

Cause

Solution

Cause

Solution

Cause

Solution

Cause

Solution

Cause

Solution

019DVX-S200-en 04.3.1, 11:24 AM102

103

Appendix A

p p

en d

ix E

n g

lish

Information

The table below lists the types of discs you can play on CinemaStation.

Video Discs

Type of Disc

DVD Video

SVCD (Super Video CD)

Video CD

Disc Logo Mark

DIGITAL VIDEO

DIGITAL VIDEO

Playable discsDestination Region code of CinemaStation

1 ALL1

The region code (an ID number assigned to each market region) is set for normal DVD players and DVD video discs. CinemaStation can play the discs with the region codes shown below on the right. For more details read the information on the disc jacket.

Advice

DVD region codes

U.S.A. Canada

2 ALL2U.K. Europe

4 ALL4Australia

3 ALL3 Korea

General Asia

Disc logo marks are printed on the disc and the disc jacket.

Disc information

Video CDs made by copying an MPEG movie file onto a CD-R or CD-RW.

Type of Disc

Music CD (Compact disc digital audio)

Super Audio CD

Disc Logo Mark

Music CDs made by copying onto a CD-R or CD-RW. Music in MP3 format can also be played.

Music Discs

019DVX-S200-en 04.3.1, 11:24 AM103

104

Appendix

The following discs cannot be played with this unit. CD-ROM, DVD-ROM, DVD-RAM, CDV.

CinemaStation cannot play a CD-R, CD-RW, DVD-R, DVD- RW, DVD+R or DVD+RW disc that has not been finalized. Finalizing is a process that prepares a disc for playback on a compatible device.

This product can play some types of DVD-R (Video format only), DVD-RW (Video format only), DVD+R or DVD+RW discs.

Only use discs from a reputable manufacturer. Some discs cannot be played back, depending on recording conditions and disc characteristics.

Do not use discs with non-standard shapes or sizes.

Some DVD video or video CD discs may operate and function differently than noted in this manual. That is by manufacturer design and not a defect in this unit. For more details read the information on the disc jacket.

This unit can play the disc types associated with the logos shown on page 103. (Do not attempt to load any other type of disc into the unit, or the unit may be damaged.)

Some discs cannot be played depending on the recording conditions such as PC environment and application software. Failure can also result from disc characteristics and condition, like material quality, scratches or curvature.

Notes

Caution

Handling a disc

Do not touch the surface of the disc. Hold a disc by its edge and center hole.

Do not leave a disc in the tray when you are not playing it.

Do not write on the disc with a pencil or other marker.

Do not stick tape, seals or other attachments to a disc, and do not bring into contact with glue.

Do not use a protective cover to prevent scratches. Do not use a disc whose surface can be printed with a

commercially available label printer.

Do not put a disc in a place with direct sunlight, high temperature, high humidity or a lot of dust.

If a disc becomes dirty, wipe it with a clean, dry cloth from the center out to the edge. Do not use record cleaner or paint thinner.

To avoid malfunction, do not use a commercially available lens cleaner.

Super Audio CD CinemaStation can play Super Audio CDs in the same manner as music CDs. However, CinemaStation cannot use the following functions for playing Super Audio CDs because the signal circuit is completely independent. DSP Program Input Signal Information Display

019DVX-S200-en 2004.04.28, 16:14104

105

Appendix A

p p

en d

ix E

n g

lish

DTS and DTS Digital Surround are registered trademarks of Digital Theater Systems, Inc.

MPEG Layer-3 audio decoding technology licensed from Fraunhofer IIS and Thomson multimedia.

Manufactured under license from Dolby Laboratories. Dolby, Pro Logic, and the double-D symbol are trademarks of Dolby Laboratories.

Copyright and logo marks This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.

SILENT CINEMA is a trademark of YAMAHA CORPORATION.

Active Servo Processing Subwoofer System with a built-in power amplifier This subwoofer system (NX-SW200) employs Advanced Yamaha Active Servo Technology which YAMAHA has developed for reproducing higher quality super-bass sound. This super-bass sound adds a more realistic, theater-in-the-home effect to your stereo system.

QD-Bass (Quatre Dispersion Bass) technology uses square, pyramid-shaped reflective plates to radiate the sound in four horizontal directions.

019DVX-S200-en 04.3.1, 11:24 AM105

106

Appendix

Glossary

Bit Stream A signal that is compressed and changed into digital format. Then depending on the decoder it can be processed as 5.1 multi-channel audio.

Channel (ch) A channel is an audio type that has been divided based on range and other characteristics. E.g. 5.1 channel Front Speakers, Left (1ch), Right (1ch) Center Speaker (1 ch) Surround Speakers, Left (1ch), Right (1ch) Subwoofer (1 ch x 0.1* = 0.1 ch)

* In contrast to a full 1-channel band, a component designed to enhance low frequency sound for added effect.

Cinema DSP (Digital Sound Field Processor) Dolby Surround and DTS were originally designed for the movie theater, so playing the same program at home would produce disparate listening experiences depending on variables like the room size, walling and number of speakers. Yamaha Cinema DSP applies original sound field technology based on a wealth of real-world data measurements to reproduce Dolby Pro Logic, Dolby Digital and DTS sound, combining them with acoustic scale, depth and tone so that you can experience the presence of a movie theater at home.

Component Video Signal A component video signal is separated into one luminance Y-signal and two chrominance PB/CB and PR/ CR signals. Since each signal is sent independently, color can be reproduced more faithfully. The component signal is also called a color-difference signal by the way it subtracts the luminance signal from the color signals.

Decoder A device that converts encoded data on DVD and other media back to its original audio or video signal.

Dolby Digital Dolby Digital is a digital surround sound system that gives you completely independent multi-channel audio. With 3 front channels (left, center, and right), and 2 surround stereo channels, Dolby Digital provides 5 full- range audio channels. With an additional channel especially for bass effects, called LFE (low frequency effect), the system has a total of 5.1 channels.

By using 2-channel stereo for the surround speakers, more accurate moving sound effects and surround sound environment can be reproduced, like the rustling of trees or sound of waves.

Dolby Pro Logic A surround system that takes a 4-channel signal and records it as a 2-channel signal, then by way of some arithmetic processing converts back to an independent 4- channel signal for playback.

Dolby Pro Logic II Takes any 2-channel source and reproduces dynamic 5.1-channel surround with excellent separation using special signal processing. You can experience Dolby Pro Logic II in MOVIE mode and MUSIC mode for stereo. You can even enjoy old movies that were only recorded in 2-channel audio (excluding monaural) in powerful 5.1-channel surround.

DTS (Digital Theater Systems) The 5.1-channel surround system adopted by most movie theaters. With an abundance of audio data, it is able to provide authentic sounding effects.

Dynamic Range The difference between the smallest sound that can be heard above the equipment noise and the biggest sound that can be heard without distortion is the dynamic range.

Film and Video Data In general, DVD media can be classified into the 2 types below. Film Data

Video recorded at 24 frames/second. (The film used for shooting movies is recorded at 24 frames/second.) Recently 30 frames/second progressive video has made its debut.

Video Data Video recorded at 30 frames/second.

CinemaStation will automatically recognize whether the source recorded on DVD is film or video, then select the best method to convert it into progressive output.

Interlace and Progressive Outputs Up to now the standard video signal has been NTSC with 525i (i: interlaced) scan lines. In contrast, 525p (p: progressive) is a high-density signal with double the number of scan lines.

019DVX-S200-en 04.3.1, 11:24 AM106

107

Appendix A

p p

en d

ix E

n g

lish

LFE (Low Frequency Effect) 0.1 Channel This channel is for the reproduction of low bass signals. The frequency range for this channel is 20 Hz to 120 Hz. It is added to the full-range 5 channels in Dolby Digital and DTS to enhance low frequency sound for added effect. This channel is counted as 0.1 because it only enforces a low frequency range.

Linear PCM (LPCM) A signal that is changed to digital format without compression. A CD is recorded with 16-bit sound at 44.1kHz, while DVD recording is anywhere from 16 bits at 48 kHz to 24 bits at 192 kHz, which makes it a higher quality sound than CD. This signal also has a type called Packed PCM (P.PCM) that can be compressed without any loss of data.

Matrix 6.1 CinemaStation incorporates a Matrix 6.1 decoder for Dolby Digital and DTS multi-channel software that enables 6.1-channel reproduction by adding the surround back channel to existing 5.1-channel format. (The surround back channel is created from surround left and right channels, and output from a virtual surround back speaker.) With this additional channel, you can experience more dynamic and realistic moving sound especially scenes with "fly-over" and "fly-around" effects.

NTSC NTSC is a video signal system (525 lines, 30 frames per second) used in North America, Central America, a number of South American countries, and some Asian countries, including Japan.

Pan & Scan and Letter Box In general, DVD Video is produced for viewing on a wide television screen with an aspect ratio of 16:9. This means you can now view most material with the intended aspect ratio on a wide-screen television. This ratio will not fit on a standard television that has an aspect ratio of 4:3. Two picture styles, Pan & Scan and Letterbox, deal with this problem. Pan & Scan cuts off the left and right portions of the

picture to fill the screen. Letterbox inserts black bands at the top and bottom of

the picture to reproduce an aspect ratio of 16:9.

PAL PAL is a video signal system (625 lines, 25 frames per second) used in the United Kingdom, much of the rest of western Europe, several South American countries, some Middle East and Asian countries, several African countries, Australia, New Zealand, and other Pacific island countries.

Sampling Frequency and Quantized Bit Rate When converting an analog signal to digital, the number of times the signal is sampled per second is called the sampling frequency while the degree of fineness when converting the sound level into a numeric value is called the quantized bit rate. The frequency band that can be played back is determined by the sampling rate while the dynamic range expressing the difference in sound level is determined by the quantized bit rate. In principle, the higher the sampling rate, the wider the frequency range that can be played back. And the higher the quantized bit rate the finer the sound that can be reproduced.

SILENT CINEMA SILENT CINEMA is an original Yamaha system that reproduces in a pair of headphones the acoustic personality of sound field programs based on multi- speakers. Headphone parameters have been set for each sound field so that natural stereoscopic sound can be expressed and enjoyed through headphones.

S-Video Signal With S-video the video signal that was normally transmitted using a pin cable is separated and transmitted as a luminance Y-signal and chrominance C- signal through an S video cable. Connecting with an S VIDEO jack you can enjoy recording and playback with more beautiful images.

Title, Chapter (DVD Video) DVD video lets you divide a disc in a big way by titles or a small way by chapters. Each division is either called a title number or a chapter number.

Track (CD/Video CD) A CD or Video CD can be divided into a number of segments (tracks). Each division is called a title number.

Virtual Cinema DSP (Digital Sound Field Processor) Reproduces a surround speaker sound field to let you enjoy virtual Center and Surround L/R Speakers with only two Front L/R Speakers.

019DVX-S200-en 04.3.1, 11:24 AM107

108

Appendix

Index 5ch Stereo ...................................................................... 17

A A-B Repeat .................................................................... 35 Action ............................................................................ 17

C Changing the Order of Preset Stations .......................... 43 CinemaStation Display brightness ................................ 92 Classic Hall .................................................................... 17 Connecting a CD or MD recorder ................................. 50 Connecting a Game Console ......................................... 46 Connecting a VCR ......................................................... 46 Connecting the Antennas ............................................... 38 Connecting the Speakers ................................................. 8 Connecting the TV .......................................................... 8

Connect a TV to an audio input ................................. 47 Connecting with S-video ................................................. 9

D D. Range ........................................................................ 91 Delay Time .................................................................... 72 Digital audio jacks ......................................................... 51 Disc information .......................................................... 103

Discs this unit cannot play back .............................. 104 Handling a disc ........................................................ 104 Music Discs ............................................................. 103 Video Discs .............................................................. 103

Disc Lock ...................................................................... 83 Disc Menu ..................................................................... 36 Display Set .................................................................... 92 Dolby Digital Surround EX disc ................................... 65 Drama ............................................................................ 17 DSP Program ................................................................. 17 DTS ES disc .................................................................. 65 DVD region codes ....................................................... 103

F Fastener ......................................................................... 54 Finding the Best DSP Effect .......................................... 16 Frame Advance .............................................................. 29

G, H Game ............................................................................. 17 HP Tone CTRL .............................................................. 91

I, J Input Assign ................................................................... 92 Input Mode .................................................................... 92 Input Modes ................................................................... 77 Jazz Club ....................................................................... 17

L L/R Balance ................................................................... 91 LEF Level ...................................................................... 91 Live Sports .................................................................... 17

M, N Matrix 6.1 ...................................................................... 65 MP3 ............................................................................... 37 Music Video ................................................................... 17 Night Listening .............................................................. 71 No Disc ........................................................................ 101 Non-skid pad ........................................................... 54, 55

O, P On Screen Menu ............................................................ 24

On Screen Menu Guide ............................................. 95 Using the On Screen Menu ........................................ 93

Original Dolby and DTS Sound .................................... 74 Parental Control ............................................................. 81 Placing the Speakers ........................................................ 7 Playback Control (PBC) ................................................ 36 PRO LOGIC II Movie ................................................... 67 PRO LOGIC II Music ................................................... 67

Pro Logic II Music setting ......................................... 68 Program Play ................................................................. 31 Progressive Scan ............................................................ 80

R Reassign input jacks ...................................................... 92 Recording Audio from CinemaStation .......................... 53 Remote Control ............................................................. 21

Amp Mode ................................................................. 22 DVD/CD Mode .......................................................... 23 Tuner Mode ................................................................ 21 Using the Remote Control ......................................... 21

Repeat Play .................................................................... 34 Rock Concert ................................................................. 17

019DVX-S200-en 04.3.1, 11:24 AM108

109

Appendix A

p p

en d

ix E

n g

lish

S SA-CD Delay ................................................................ 91 Sci-Fi (Science Fiction) ................................................. 17 Selecting Radio Stations ................................................ 39

Auto Tuning ............................................................... 39 Manual Tuning ........................................................... 40 Preset Tuning ............................................................. 43

SET MENU ................................................................... 91 Setting Channels in Advance (Preset) ........................... 41

Auto Preset ................................................................ 41 Manual Preset ............................................................ 42

Setting the Manufacturer Code ...................................... 84 SILENT CINEMA ..................................................... 70 Sleep Timer .................................................................... 79 Slow Advance/Reverse .................................................. 29 SP Delay ........................................................................ 91 Speaker Mode ................................................................ 63 Speaker Size .................................................................. 63 Speaker Volume Level ............................................. 59, 61

5ch Stereo DSP Program ........................................... 62 Spectacle ........................................................................ 17 Stereo playback ............................................................. 17 Super Audio CD .......................................................... 104

T Test Tone ........................................................................ 59 Theater ........................................................................... 17 Time Search ................................................................... 30 To change discs .............................................................. 12 Tuner Step ...................................................................... 92 Types of Input Signals ................................................... 76

V Virtual Cinema DSP ...................................................... 69

019DVX-S200-en 04.3.1, 11:24 AM109

110

Appendix

Specifications

AUDIO SECTION Minimum RMS Output Power

FRONT L/R, CENTER, SURROUND L/R 1 kHz, 0.9% THD, 6 ........................................... 85 W U.S.A. and Canada models 20 Hz to 20 kHz, 0.9% THD, 6 ........................ 80 W

Maximum Power (EIAJ) (Asia, Korea and General models only)

FRONT L/R, CENTER, SURROUND L/R 1 kHz, 10% THD, 6 ........................................... 100 W

Total Harmonic Distortion FRONT L/R (20 W, 1 kHz) .................. Less than 0.05 %

Signal to Noise Ratio (IHF-A Network, 200 mV shorted) ............................................................................... 95 dB

Input Sensitivity VIDEO 1, VIDEO 2 (VIDEO), VCR, MD/CD-R ................................................................. 200 mV/47 k

Output Level (when 200mV is input) REC OUT ............................................... 200 mV/1.2 k PRE OUT (SUBWOOFER) ....................................... 4 V Headphones .............................................. 220 mV/100

VIDEO SECTION Video Signal Level

Video ............................................................ 1 Vp-p/75 S Video (Y/C) ......................... 1 Vp-p/0.286 Vp-p/75 Component (Y/PB, PR) ................. 1 Vp-p/0.7 Vp-p/75

Signal to Noise Ratio .................................................... 50 dB

TUNER SECTION FM Tuning Range

U.S.A. and Canada models ................ 87.5 to 107.9 MHz Other models ...................................... 87.5 to 108.0 MHz

AM Tuning Range U.S.A., Canada and Korea models ....... 530 to 1710 kHz U.K., Europe and Australia models ...... 531 to 1611 kHz Asia and General models ...... 530/531 to 1710/1611 kHz

SPEAKERS Satellite Speakers (Front and Surround Speakers)

Model Name ..................................................... NX-S200 Type ............... 2-way acoustic suspension magnetic shielding type

Driver .... Tweeter: 2.5 cm (1 inch) balanced dome magnetic shielding type

Woofer: 5 cm (2 inch) cone magnetic shielding type Impedance ................................................................... 6

Center Speaker Model Name .................................................... NX-C200 Type ............... 2-way acoustic suspension magnetic shielding type

Driver .... Tweeter: 2.5 cm (1 inch) balanced dome magnetic shielding type

Woofer: 5 cm (2 inch) cone magnetic shielding type

Impedance ................................................................... 6 Subwoofer

Model Name ................................................. NX-SW200 Type ........ Advanced YAMAHA Active Servo Technology system

Driver ................ 20 cm (8 inch) cone, magnetic shielding type

GENERAL Power Supply

U.S.A. and Canada models ................... AC 120 V/60 Hz Australia model ..................................... AC 240 V/50 Hz U.K. and Europe models ....................... AC 230 V/50 Hz Korea model .......................................... AC 220 V/60 Hz Asia model ............................... AC 220-240 V, 50/60 Hz General model .......................... AC 110-120 V, 50/60 Hz

Power Consumption DVR-S200 ............................................................ 130 W NX-SW200 ............................................................. 85 W

Standby Power Consumption DVR-S200 Asia and General models ....................................... 0.5 W Other models ........................................................ 0.35 W

Laser Pickup Type .................................. Semiconductor laser GaAlAs Wave length ............ 650 nm (DVD), 790 nm (VCD/CD) Output Power .... 1.45 mW (DVD), 1.31 mW (VCD/CD)

Dimensions (W H D) DVR-S200 ...................................... 360 80 361 mm

(14 3/16 x 3 5/32 x 14 7/32) NX-SW200 ................................... 232 415 388 mm

(9 1/8 x 16 11/32 x 15 9/32) NX-C200 ........................................... 300 72 81 mm

(11 13/16 x 2 27/32 x 3 3/16) NX-S200 ........................................... 72 230 81 mm

(2 27/32 x 9 1/16 x 3 3/16) Weight

DVR-S200 ........................................ 6.5 kg (14 lbs 5 oz) NX-SW200 ....................................... 9.6 kg (21 lbs 3 oz) NX-C200 ............................................. 1.1 kg (2 lbs 6 oz) NX-S200 ............................................. 1.0 kg (2 lbs 3 oz)

Operating Temperature Range ........ +5 to +35C (41 to 95F) Operating Humidity Range ...... 5 to 90% (No Condensation) Accessories ........................................................... See page 6.

Specifications are subject to change without notice.

019DVX-S200-en 04.3.1, 11:24 AM110

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD18 7GQ, ENGLAND YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VSTRA FRLUNDA, SWEDEN YAMAHA MUSIC AUSTRALIA P

Manualsnet FAQs

If you want to find out how the DVR-S200 Yamaha works, you can view and download the Yamaha DVR-S200 Theater System Owner's Manual on the Manualsnet website.

Yes, we have the Owner's Manual for Yamaha DVR-S200 as well as other Yamaha manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Owner's Manual should include all the details that are needed to use a Yamaha DVR-S200. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Yamaha DVR-S200 Theater System Owner's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Yamaha DVR-S200 Theater System Owner's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Yamaha DVR-S200 Theater System Owner's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Yamaha DVR-S200 Theater System Owner's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Yamaha DVR-S200 Theater System Owner's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.