Yamaha HS840 Stand Owner's Manual PDF

1 of 1
1 of 1

Summary of Content for Yamaha HS840 Stand Owner's Manual PDF

r Spring Tension Knob The Spring Tension Knob supplies tension control over a 11-step range, To increase tension, slide the Spring Tension Knob up (Fig. A) to any position you like (use the scale as a reference) and then rotate the knob to the left to lock in place. (Fig. B) To reduce tension, rotate the Spring Tension Knob to the right (Fig. C) and slide to any position you like. To increase tension, slide the Spring Tension Knob up, to decrease tension, slide the Spring Tension Knob down.

t Footboard Stabilizer Rod The Footboard stabilizer rod should attach to holes in the frame at the bottom of the hi-hat base.

y Spur The large heavy-duty rubber feet prevent unwanted movement of the hi-hat stand during playing conditions. To minimize slippage further, there are two spurs in the frame. These spurs can be extended as needed by adjusting the turn screws pro- vided on either side of the frame base.

u Leg Position Adjustment Loosen Bolts A and B shown in the illustration to the right to change the position of the legs (footboard). After the posi t ion has been determined, tighten both Bolts A and B firmly. Also, we recommend that the legs be positioned in the same manner as shown in the illustration on the left so as to leave some space available for setup and to provide sufficient stability for the stand. (This setup is for right-handed drummers. For left-handed drummers, please set up in an opposite manner.)

Note: To maintain smooth action, occasionally apply some grease-grade oil to all of the moving parts. Be careful not to use excessive force when tightening the extender base nut as this may damage the nylon bushing inside the tube.

q Cymbal Support Plate To install the bottom hi-hat cymbal, remove the hi-hat clutch assembly and place the cymbal on the felt washer on the cymbal support plate. The angle of the bottom cymbal can be adjusted by turning the angle bolt on the underside of the support plate. To adjust the angle of the hi-hat cymbal, use the Knob Bolt located on the underside of the cymbal support.

w Hi-Hat Clutch To install the top hi-hat cymbal, loosen the wing bolt and remove the entire hi- hat clutch assembly from the upper pull rod. Next, remove the clutch nut and position the cymbal between the two clutch felts. After installation, tighten the clutch nut on to the clutch assembly to secure the cymbal. Place the entire assembly onto the hi hat upper pull rod and tighten the wing bolt to secure the desired position of the top cymbal. The lock nuts on the top of the clutch can adjust the feel and sound of the hi hat cymbals. To obtain a loose sound, open the nuts off of the felt; for a tight sound, close the nuts onto the felt. Once the desired sound has been ob- tained, tighten firmly the lock nuts onto each other.

e Position Clamp Once the bottom hi-hat cymbal height has been decided, the position clamp can be used to mark the settings for future set ups and to prevent uninten- tional changes during musical performances. Use a drum key to firmly tighten the position clamp into place.

* Specifications and design are subject to change without notice.

Introduction

Thank you for purchasing a Yamaha Hi-Hat Stand. Please read this owner's manual thoroughly before use.

HI-HAT STAND

HS840/HS740 OWNER'S MANUAL

CAUTION

To prevent the Hi-Hat Stand from coming loose during performance, tighten all securing bolts and adjustment bolts firmly.

To maintain smooth action, apply some grease-grade oil (ex. lithium grease) to all of the moving parts as needed.

Hi-Hat Clutch

Cymbal Support Plate

Knob Bolt

Position Clamp

Extender Base

Footboard

Spur Footboard Stabilizer Rod

Hi-Hat Shaft

A

B

Spring Tension Knob

Manualsnet FAQs

If you want to find out how the HS840 Yamaha works, you can view and download the Yamaha HS840 Stand Owner's Manual on the Manualsnet website.

Yes, we have the Owner's Manual for Yamaha HS840 as well as other Yamaha manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Owner's Manual should include all the details that are needed to use a Yamaha HS840. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Yamaha HS840 Stand Owner's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Yamaha HS840 Stand Owner's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Yamaha HS840 Stand Owner's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Yamaha HS840 Stand Owner's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Yamaha HS840 Stand Owner's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.