Yamaha HS1100 Stand Owner's Manual PDF

1 of 1
1 of 1

Summary of Content for Yamaha HS1100 Stand Owner's Manual PDF

Protect Sheet

t Connecting Rod Connecting the rod to the frame secures the footboard to the frame.

y Spikes The spikes prevent the hi-hat stand from sliding forward. The unit is equipped with four spikes, one in each of the front legs rubber feet and two on the frame. Spikes located in the legs rubber feet can be extended by loosening the drum key bolt. Those in the frame can be extended to the preferred length by rotating the bolts clockwise.

u Adjusting Leg Position The position of the legs (footboard) can be ad- justed by loosening bolts A and B, shown in the diagram on the right. After the position has been determined, firmly tighten bolts A and B.

i Adjust the Footboard Angle The angle adjuster can be used to increase or decrease the amount of footboard angle by raising or lowering the adjuster. With a drum key, loosen the two bolts on either side of the angle adjuster then slide the angle adjuster higher or lower as needed. After the angle has been determined, firmly tighten two bolts with a drum key.

q Cymbal Support Plate To attach the bottom hi-hat cymbal first, remove the hi-hat clutch and set the bottom hi-hat cymbal on the rubber washer. At this time, make sure that the metal plate and the rubber washer are on the cymbal support plate. Rotate the knurled head bolt, located under the plate, to adjust the angle of the cymbal then secure with the fixing nut.

w Hi-Hat Clutch (LC-930) The top hi-hat cymbal is fixed and held in place between the two felts of the hi-hat clutch.

(Procedure) 1) Loosen the drum key bolt q on the clutch nut and remove the clutch

nut from the clutch bolt. 2) Remove the lower felt and place the cymbal between the upper felt

and the lower removed felt. 3) Firmly tighten the clutch nut onto the clutch bolt. Next, tighten the

drum key bolt q to lock the clutch nut. Since the drum key bolt q can be locked with a minimum of force, be sure not to over tighten which may cause damage to the bolt.

4) The lock nut adjusts the amount of pressure used to hold the cymbal in place. Loosen the drum key bolt w and raise or lower the lock nut to adjust the position. After the position has been determined, tighten the drum key bolt w to lock the lock nut in place. The drum key bolt w can be locked with a minimum of force so be sure not to over tighten which may cause damage to the bolt.

e Memory Clamp After you have determined the height of the hi-hat cymbal, secure the memory clamp at the base assemblys pipe holder to set a memory of the pipes position for future settings. At this time, make sure the memory clamp fits into the pipe holder. Use a drum key to firmly tighten the memory clamp so as to prevent the pipe from slipping during performance. Also, the pipe holder is equipped with a drum key holder. (The drum key is optional.)

r Spring Tension Adjustment The large adjustment dial adjusts spring tension. Turning the dial to the left increases tension while turning to the right decreases tension. Also, this system is equipped with a tension indicator that conveniently displays the amount of tension.

Introduction

Thank you for purchasing this Yamaha Hi-Hat Stand.

In order to obtain maximum performance and longevity from hi-hat stand,

please read this Owners Manual thoroughly.

Printed in Japan

Memory Clamp

Pipe Holder Bolt

Angle Adjuster

Rubber Washer

Metal Plate

Cymbal Support Plate

Fixing Nut

Knurled Head Bolt

Footboard (example: HS1100)

Leg

HI-HAT STAND OWNER'S MANUAL

* Specifications and design are subject to change without notice.

CAUTION

To prevent the Hi-Hat Stand from coming loose during per- formance, tighten all securing bolts and adjustment bolts firmly.

To maintain smooth action, apply some grease-grade oil (ex. lithium grease) to all of the moving parts as needed.

Drum Key Bolt q

Drum Key Bolt w Wing Bolt

Clutch Bolt

Lock Nut

Felt

Clutch Nut

o Heel A removable rubber base is attached to the underside of the heel. Remarry the rubber, reveals a strip of Velcro that, provides better grip when the stand is used on carpeted surfaces, etc. If the Velcro does not provide sufficient grip, use the rubber.

!0 The Supplied Soft Case and Sheet To protect the hi-hat stand's finish from scratches, etc., werecommend that it be placed in the supplied soft case when transporting. Also, please wrap the upper pipe in the supplied sheet.

!1 A protective sheet A protective sheet is applied to the HS1100 to protect the finish.

Note) Moving parts require occasional lubrication for smooth operation. Also, over tightening of the nylon clutch inside the base assemblys pipe holder may result in damage. Please use caution.

HS1000 Hi-Hat Clutch

Hi-Hat Shaft

Fixing Nut

Spikes

Memory Clamp

Knurled Head Bolt

Cymbal Support Plate

Base Assembly Pipe Holder

Heel

Footboard

Adjustment Dial

Indicator

Bolt A

Bolt B

Angle Adjuster

Hi-Hat Clutch

Hi-Hat Shaft

Fixing Nut

Spikes

Memory Clamp

Knurled Head Bolt

Cymbal Support Plate

Base Assembly Pipe Holder

Heel

Footboard

Adjustment Dial

Indicator

Bolt A

Bolt B

Angle Adjuster

HS1100 HS950 Hi-Hat Clutch

Hi-Hat Shaft

Fixing Nut

Spikes

Memory Clamp

Knurled Head Bolt

Cymbal Support Plate

Base Assembly Pipe Holder

Heel

Footboard

Adjustment Dial

Manualsnet FAQs

If you want to find out how the HS1100 Yamaha works, you can view and download the Yamaha HS1100 Stand Owner's Manual on the Manualsnet website.

Yes, we have the Owner's Manual for Yamaha HS1100 as well as other Yamaha manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Owner's Manual should include all the details that are needed to use a Yamaha HS1100. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Yamaha HS1100 Stand Owner's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Yamaha HS1100 Stand Owner's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Yamaha HS1100 Stand Owner's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Yamaha HS1100 Stand Owner's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Yamaha HS1100 Stand Owner's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.