Yamaha NS-100S Speaker Owner's Manual PDF

Download download
Yamaha NS-100S Speaker Owner's Manual PDF
Yamaha Manual Yamaha Speaker Manual Yamaha NS-100S Manual Yamaha Speaker Owner's Manual
Pages 2
Year 0
Language(s)
English en
1 of 2
1 of 2

Summary of Content for Yamaha NS-100S Speaker Owner's Manual PDF

Page 1

English

Read these precautions carefully before using your speaker. Any time you note distortion, reduce the volume control on your

amplifier to a lower setting. Never allow your amplifier to be driven into clipping. Otherwise the speaker may be damaged.

When using an amplifier with a rated output power higher than the nominal input power of the speaker, care should be taken never to exceed the speakers maximum input.

Do not attempt to clean the speaker with chemical solvents as this might damage the finish. To clean, wipe with a dry, soft cloth.

To prevent the enclosure from warping or discoloring, do not place the speaker where it will be exposed to direct sunlight or excessive humidity.

Do not place the speaker where it is liable to be knocked over or struck by falling objects. Stable placement will also ensure better sound performance.

Secure placement or installation is the owners responsibility. YAMAHA shall not be liable for any accident caused by improper placement or installation of the speaker.

NS-100S GT

Speaker System

Thank you for selecting this YAMAHA NS-100S speaker system.

PRECAUTIONS

OWNERS MANUAL

PLACING THE SPEAKER The rear center speaker should be placed behind the listening position, and equidistant from the two surround speakers. The positioning of the rear center speaker is important, because it controls the whole sound quality of a multi channel system.

Type .......................... 2-way 2-speaker bass reflex speaker system (Magnetically-shielded type)

Speaker Unit ............................................ 16 cm (6.5) cone woofer 3 cm (1) dome tweeter

Nominal Impedance ............................................................. 6 ohms Frequency Response ............................................... 38 Hz 35 kHz Nominal Input Power .............................................................. 100 W Maximum Input Power ........................................................... 300 W Sensitivity ................................................................ 90 dB/2.83 V/m Crossover Frequency .............................................................. 3 kHz Dimensions (W x H x D) ................................... 212 x 416 x 270 mm

(8.3 x 16.4 x 10.6) Weight ................................................................... 8.6 kg (19.0 lbs.)

Specifications subject to change without notice due to product improvements.

Care should be taken not to exceed the input power values noted above.

SPECIFICATIONSREMOVING THE FRONT COVER The front cover is fastened to the enclosure at four points, and can be removed if desired. To remove the cover, hold on to both sides and slowly pull straight away from the speaker. To reattach, line up the four pegs on the inside surface of the cover with the four corresponding holes on the speaker and push gently.

Note When the cover is removed, take care not to touch the speaker units with your hands or to exert excessive force with tools.

Surround R

Main R

Main L

Center

Surround L

NS-100S (Rear center speaker)

Subwoofer

Page 2

CENTER

+

REAR

CONNECTIONS TO YOUR AMPLIFIER

Leave the short bars in place when connecting.

Short bar

This speaker system is capable of standard connections and bi-wiring connections. Before making connections, make sure that the amplifier is switched off.

+

Remove the short bars before connecting.

Connections Connect the screw-type input terminals at the rear of the speaker

to the speaker output terminals of your amplifier with the speaker cables.

Connect the (+) terminals on both the amplifier and the speaker using one side of the cable. Connect the () terminals on both components using the other side of the cable.

Connect the speaker to the rear center terminals of your amplifier, making sure not to reverse the polarity (+, ). If this speaker is connected with reversed polarity, the sound will be unnatural and lack bass.

Procedure: Loosen the terminal knob. Remove approx. 10 mm (3/8) insulation from the speaker

cable and insert the bare wire end properly into the terminal hole.

Tighten the knob. Test the security of the connections by tugging lightly on the

cable at the terminal.

Note Do not let the bare speaker wires touch each other as this could damage the speaker and/or the amplifier.

Rear center speaker

Amplifier or Receiver

CENTER

+

REAR

Woofer terminals

Rear center speaker

Amplifier or Receiver

Loosen

Tighten

Tweeter terminals

+

Bi-Wiring Connections This speaker system is capable of bi-wiring connections. To connect the speaker to the output terminals of the amplifier, two pairs of cables for each of woofer and tweeter are used instead of standard connections. This type of connection decreases the modulation distortion caused by electric resistance of the cables and driving current of the speakers. Consequently, purer sound quality can be expected.

To utilize bi-wiring connections, remove the short bars from the terminals first, and then connect the woofer and tweeter to th

Manualsnet FAQs

If you want to find out how the NS-100S Yamaha works, you can view and download the Yamaha NS-100S Speaker Owner's Manual on the Manualsnet website.

Yes, we have the Owner's Manual for Yamaha NS-100S as well as other Yamaha manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Owner's Manual should include all the details that are needed to use a Yamaha NS-100S. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Yamaha NS-100S Speaker Owner's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Yamaha NS-100S Speaker Owner's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Yamaha NS-100S Speaker Owner's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Yamaha NS-100S Speaker Owner's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Yamaha NS-100S Speaker Owner's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.