Contents

Yamaha XC50J Vino 2018 Owner's Manual PDF

1 of 84
1 of 84

Summary of Content for Yamaha XC50J Vino 2018 Owner's Manual PDF

1TS-F8199-15

XC50J

Read this manual carefully before operating this vehicle.

OWNERS MANUAL

LIT-11626-31-32

1TS-F8199-13_Cov.indd 1 2015/06/17 15:00:16

EAU10043

Read this manual carefully before operating this vehicle. This manual should stay with this vehicle if it is sold.

1TS-F8199-12_Cov.indd 2 2014/06/23 14:42:51

INTRODUCTION EAU10093

amahas vast experience in the pro- h degree of craftsmanship and reli-

ntenance of this scooter. If you have t a Yamaha dealer. ndards for clean air applicable at the nce or economy of operation of the ealer pay close attention to the rec- nual.

le this manual contains the most cur- ncies between your scooter and this ler.

EWA12582

booklet carefully and completely ave attained adequate knowledge proper riding techniques. Regular t you safely enjoy the capabilities

U1TS12E0 1

Co du ab Th an Th da sc om Ya re m

Pl be of in an

ngratulations on your purchase of the Yamaha XC50J. This model is the result of Y ction of fine sporting, touring, and pacesetting racing machines. It represents the hig ility that have made Yamaha a leader in these fields. is manual will give you an understanding of the operation, inspection, and basic mai y questions concerning the operation or maintenance of your scooter, please consul e design and manufacture of this Yamaha scooter fully comply with the emissions sta te of manufacture. Yamaha has met these standards without reducing the performa ooter. To maintain these high standards, it is important that you and your Yamaha d mended maintenance schedules and operating instructions contained within this ma maha continually seeks advancements in product design and quality. Therefore, whi

nt product information available at the time of printing, there may be minor discrepa anual. If there is any question concerning this manual, please consult a Yamaha dea

WARNING

ease read this manual and the YOU AND YOUR MOTORCYCLE: RIDING TIPS fore operating this scooter. Do not attempt to operate this scooter until you h its controls and operating features and until you have been trained in safe and spections and careful maintenance, along with good riding skills, will ensure tha d reliability of this scooter.

EAU10134

ns:

to potential personal injury ymbol to avoid possible injury

if not avoided, could result in

e taken to avoid damage to the

ier or clearer.

U1TS12E0 1

IM

Pa

*Pr

N

TI

PORTANT MANUAL INFORMATION

rticularly important information is distinguished in this manual by the following notatio

oduct and specifications are subject to change without notice.

This is the safety alert symbol. It is used to alert you hazards. Obey all safety messages that follow this s or death.

A WARNING indicates a hazardous situation which, death or serious injury.

A NOTICE indicates special precautions that must b vehicle or other property.

A TIP provides key information to make procedures eas

WARNING

OTICE

P

IMPORTANT MANUAL INFORMATION

U1TS12E0 2

2017 by Y

Any re withou Yamah

is

EAUT2192

XC50J OWNERS MANUAL

amaha Motor Corporation, U.S.A. 1st edition, June 2017

All rights reserved. printing or unauthorized use

t the written permission of a Motor Corporation, U.S.A. expressly prohibited. Printed in Taiwan.

P/N LIT-11626-31-32

hecking the throttle grip free play............................................. 6-14

alve clearance ............................. 6-14 ires............................................... 6-15 ast wheels ................................... 6-16 djusting the brake lever free play............................................. 6-16

djusting the rear brake lever free play............................................. 6-17 hecking the front and rear brake shoes.......................................... 6-18 hecking and lubricating the cables ......................................... 6-18 hecking and lubricating the throttle grip and cable............................. 6-19

ubricating the front and rear brake levers.......................................... 6-19 hecking and lubricating the centerstand................................. 6-19 hecking the front fork................... 6-20 hecking the steering .................... 6-20 hecking the wheel bearings......... 6-21 attery ........................................... 6-21 eplacing the fuse ......................... 6-22 eplacing the headlight bulb ......... 6-23 eplacing the tail/brake light bulb............................................. 6-24 eplacing a turn signal light bulb............................................. 6-24

roubleshooting ............................. 6-25 roubleshooting charts .................. 6-26

U1TS12E0 1

TA LO LA

SA F

DE L R C

INS FU

M I S F H F R R F F C S H S C L

BLE OF CONTENTS CATION OF IMPORTANT BELS.............................................. 1-1

FETY INFORMATION ................... 1-3 urther safe-riding points................. 1-7

SCRIPTION ................................... 2-1 eft view .......................................... 2-1 ight view ........................................ 2-2 ontrols and instruments................. 2-3

TRUMENT AND CONTROL NCTIONS ....................................... 3-1 ain switch/steering lock................. 3-1

ndicator lights and warning light ..... 3-2 peedometer unit ............................ 3-3 uel gauge....................................... 3-3 andlebar switches ......................... 3-4 ront brake lever ............................. 3-5 ear brake lever .............................. 3-5 ear wheel lock ............................... 3-5 uel tank cap ................................... 3-6 uel.................................................. 3-7 atalytic converters ......................... 3-8 eat ................................................. 3-9 elmet holder .................................. 3-9 torage compartments .................. 3-10 arrier............................................ 3-11 uggage hook................................ 3-12

FOR YOUR SAFETY PRE-OPERATION CHECKS ............................................ 4-1

OPERATION AND IMPORTANT RIDING POINTS .............................................. 5-1

Starting a cold engine ..................... 5-1 Starting off....................................... 5-2 Acceleration and deceleration......... 5-2 Braking ............................................ 5-2 Tips for reducing fuel

consumption ................................ 5-3 Engine break-in ............................... 5-3 Parking ............................................ 5-4

PERIODIC MAINTENANCE AND ADJUSTMENT ................................... 6-1

Periodic maintenance chart for the emission control system .............. 6-3

General maintenance and lubrication chart............................................. 6-4

Removing and installing the panel ............................................ 6-7

Checking the spark plug.................. 6-7 Engine oil and oil strainer................ 6-9 Final transmission oil..................... 6-11 Coolant.......................................... 6-12 Replacing the air filter element and

cleaning the check hose ............ 6-13 Checking the engine idling

speed ......................................... 6-14

C

V T C A

A

C

C

C

L

C

C C C B R R R

R

T T

BLE OF CONTENTS S

S

C

U1TS12E0 2

TA COOTER CARE AND STORAGE ... 7-1 Matte color caution .......................... 7-1 Care................................................. 7-1 Storage............................................ 7-4

PECIFICATIONS.............................. 8-1

ONSUMER INFORMATION............. 9-1 Identification numbers ..................... 9-1 Reporting safety defects.................. 9-3 Scooter noise regulation.................. 9-4 Maintenance record......................... 9-5 YAMAHA MOTOR CORPORATION,

U.S.A. 2015 AND LATER MODEL SCOOTER LIMITED WARRANTY ................................ 9-7

YAMAHA EXTENDED SERVICE (Y.E.S.) ........................................ 9-9

1

EAU10385

ion for safe and proper operation of ad or comes off, a replacement label

U1TS12E0 1

LO

Re you is a

1-1

CATION OF IMPORTANT LABELS

ad and understand all of the labels on your vehicle. They contain important informat r vehicle. Never remove any labels from your vehicle. If a label becomes difficult to re vailable from your Yamaha dealer.

3,4,5,6

1

2

MPORTANT LABELS

1

2

3

4

5

6

7

8

9

1TS-F4876-00

LIMIT 5 kg{11 lbs} 3 kg{ 7 lbs}

U1TS12E0 2

LOCATION OF I

1-2

1

2

3

4

5

6

WARNING

1CD-F118K-00

LOAD BOX CARRIER

1CD-F4875-00

WARNING NEVER sit on carrier.

1CD-F4877-00

LOAD LIMIT HOOK 1 kg{2 lbs} COMPARTMENT 1.5 kg{3 lbs}

1

approaching and passing through intersections, since in- tersections are the most likely places for scooter accidents to occur.

Ride where other motorists can see you. Avoid riding in another motorists blind spot.

Never maintain a scooter with- out proper knowledge. Contact an authorized scooter dealer to inform you on basic scooter maintenance. Certain mainte- nance can only be carried out by certified staff.

Many accidents involve inexperi- enced operators. In fact, many op- erators who have been involved in accidents do not even have a cur- rent drivers license. Make sure that you are qualified

and that you only lend your scooter to other qualified opera- tors.

Know your skills and limits. Staying within your limits may help you to avoid an accident.

We recommend that you prac- tice riding your scooter where

U1TS12E0 3

Be As sib of y Sc Th pen tec the kno ridi He

1-3

SAFETY INFORMATION EAU10249

a Responsible Owner the vehicles owner, you are respon- le for the safe and proper operation our scooter.

ooters are single-track vehicles. eir safe use and operation are de- dent upon the use of proper riding

hniques as well as the expertise of operator. Every operator should w the following requirements before

ng this scooter. or she should:

Obtain thorough instructions from a competent source on all aspects of scooter operation. Observe the warnings and mainte- nance requirements in this Own- ers Manual. Obtain qualified training in safe and proper riding techniques. Obtain professional technical ser- vice as indicated in this Owners Manual and/or when made neces- sary by mechanical conditions. Never operate a scooter without proper training or instruction. Take a training course. Beginners

should receive training from a cer- tified instructor. Contact an autho- rized scooter dealer to find out about the training courses nearest you.

Safe Riding Perform the pre-operation checks each time you use the vehicle to make sure it is in safe operating condition. Failure to inspect or maintain the vehicle properly increases the possibility of an accident or equipment damage. See page 4-1 for a list of pre-operation checks. This scooter is designed to carry

the operator only. No passengers. The failure of motorists to detect

and recognize scooters in traffic is the predominating cause of auto- mobile/scooter accidents. Many accidents have been caused by an automobile driver who did not see the scooter. Making yourself con- spicuous appears to be very effec- tive in reducing the chance of this type of accident. Therefore: Wear a brightly colored jacket. Use extra caution when you are

1

FETY INFORMATION n monoxide can cause headaches, ziness, drowsiness, nausea, confu- n, and eventually death. rbon Monoxide is a colorless, odor- s, tasteless gas which may be pres- t even if you do not see or smell any gine exhaust. Deadly levels of car- n monoxide can collect rapidly and u can quickly be overcome and un- le to save yourself. Also, deadly lev- of carbon monoxide can linger for urs or days in enclosed or poorly ntilated areas. If you experience any

ptoms of carbon monoxide poison- , leave the area immediately, get sh air, and SEEK MEDICAL TREAT- NT. Do not run engine indoors. Even if you try to ventilate engine exhaust with fans or open windows and doors, carbon monoxide can rap- idly reach dangerous levels. Do not run engine in poorly venti- lated or partially enclosed areas such as barns, garages, or car- ports. Do not run engine outdoors where engine exhaust can be drawn into a building through openings such

U1TS12E0 4

1-4

SA there is no traffic until you have become thoroughly familiar with the scooter and all of its con- trols.

Many accidents have been caused by error of the scooter operator. A typical error made by the operator is veering wide on a turn due to ex- cessive speed or undercornering (insufficient lean angle for the speed). Always obey the speed limit and

never travel faster than warrant- ed by road and traffic conditions.

Always signal before turning or changing lanes. Make sure that other motorists can see you.

The posture of the operator is im- portant for proper control. The op- erator should keep both hands on the handlebar and both feet on the operator footrests during operation to maintain control of the scooter.

Never ride under the influence of alcohol or other drugs.

This scooter is designed for on-road use only. It is not suitable for off-road use.

Protective Apparel The majority of fatalities from scooter accidents are the result of head inju- ries. The use of a safety helmet is the single most critical factor in the preven- tion or reduction of head injuries. Always wear an approved helmet. Wear a face shield or goggles.

Wind in your unprotected eyes could contribute to an impairment of vision that could delay seeing a hazard.

The use of a jacket, substantial shoes, trousers, gloves, etc., is ef- fective in preventing or reducing abrasions or lacerations.

Never wear loose-fitting clothes, otherwise they could catch on the control levers or wheels and cause injury or an accident.

Always wear protective clothing that covers your legs, ankles, and feet. The engine or exhaust sys- tem become very hot during or af- ter operation and can cause burns.

Avoid Carbon Monoxide Poisoning All engine exhaust contains carbon monoxide, a deadly gas. Breathing car-

bo diz sio Ca les en en bo yo ab els ho ve sym ing fre ME

1 Lo Ad sc an th po ca rie wh ca th low low Th so m ov ac

W ke

aha accessories, which are avail- e only from a Yamaha dealer, have n designed, tested, and approved amaha for use on your vehicle.

ny companies with no connection to aha manufacture parts and acces-

ies or offer other modifications for aha vehicles. Yamaha is not in a

ition to test the products that these rmarket companies produce. refore, Yamaha can neither en- se nor recommend the use of ac- sories not sold by Yamaha or difications not specifically recom- nded by Yamaha, even if sold and alled by a Yamaha dealer.

ermarket Parts, Accessories, Modifications

ile you may find aftermarket prod- similar in design and quality to uine Yamaha accessories, recog- that some aftermarket accessories

modifications are not suitable be- se of potential safety hazards to you others. Installing aftermarket prod- or having other modifications per- ed to your vehicle that change any

the vehicles design or operation

U1TS12E0 5

1-5

SAFETY INFORMATION as windows and doors.

ading ding accessories or cargo to your ooter can adversely affect stability d handling if the weight distribution of e scooter is changed. To avoid the ssibility of an accident, use extreme ution when adding cargo or accesso- s to your scooter. Use extra care en riding a scooter that has added rgo or accessories. Here, along with e information about accessories be-

, are some general guidelines to fol- if loading cargo to your scooter:

e total weight of the operator, acces- ries and cargo must not exceed the aximum load limit. Operation of an erloaded vehicle could cause an cident.

hen loading within this weight limit, ep the following in mind:

Cargo and accessory weight should be kept as low and close to the scooter as possible. Securely

pack your heaviest items as close to the center of the vehicle as pos- sible and make sure to distribute the weight as evenly as possible on both sides of the scooter to min- imize imbalance or instability.

Shifting weights can create a sud- den imbalance. Make sure that ac- cessories and cargo are securely attached to the scooter before rid- ing. Check accessory mounts and cargo restraints frequently. Properly adjust the suspension

for your load (suspension-ad- justable models only), and check the condition and pres- sure of your tires.

Never attach any large or heavy items to the handlebar, front fork, or front fender. Such items can create unstable handling or a slow steering response.

This vehicle is not designed to pull a trailer or to be attached to a sidecar.

Genuine Yamaha Accessories Choosing accessories for your vehicle is an important decision. Genuine

Yam abl bee by Y Ma Yam sor Yam pos afte The dor ces mo me inst

Aft and Wh ucts gen nize or cau or ucts form of

Maximum load: 91 kg (201 lb)

1

FETY INFORMATION ch a Y to K a in

, and combinations may not be propriate. Refer to page 6-15 for tire ecifications and more information on lacing your tires.

nsporting the Scooter sure to observe following instruc- ns before transporting the scooter in other vehicle.

Remove all loose items from the scooter. Point the front wheel straight ahead on the trailer or in the truck bed, and choke it in a rail to pre- vent movement. Secure the scooter with tie-downs or suitable straps that are attached to solid parts of the scooter, such as the frame or upper front fork tri- ple clamp (and not, for example, to rubber-mounted handlebars or turn signals, or parts that could break). Choose the location for the straps carefully so the straps will not rub against painted surfaces during transport. The suspension should be com- pressed somewhat by the tie-downs, if possible, so that the

U1TS12E0 6

1-6

SA aracteristics can put you and others

t greater risk of serious injury or death. ou are responsible for injuries related changes in the vehicle. eep the following guidelines in mind, s well as those provided under Load- g when mounting accessories. Never install accessories or carry

cargo that would impair the perfor- mance of your scooter. Carefully inspect the accessory before using it to make sure that it does not in any way reduce ground clearance or cornering clearance, limit sus- pension travel, steering travel or control operation, or obscure lights or reflectors. Accessories fitted to the handle-

bar or the front fork area can create instability due to improper weight distribution or aerody- namic changes. If accessories are added to the handlebar or front fork area, they must be as lightweight as possible and should be kept to a minimum.

Bulky or large accessories may seriously affect the stability of the scooter due to aerodynamic

effects. Wind may attempt to lift the scooter, or the scooter may become unstable in cross winds. These accessories may also cause instability when passing or being passed by large vehicles.

Certain accessories can dis- place the operator from his or her normal riding position. This improper position limits the free- dom of movement of the opera- tor and may limit control ability, therefore, such accessories are not recommended.

Use caution when adding electri- cal accessories. If electrical acces- sories exceed the capacity of the scooters electrical system, an electric failure could result, which could cause a dangerous loss of lights or engine power.

Aftermarket Tires and Rims The tires and rims that came with your scooter were designed to match the performance capabilities and to provide the best combination of handling, brak- ing, and comfort. Other tires, rims, siz-

es ap sp rep

Tra Be tio an

1

and ankle so they do not flap), and a brightly colored jacket. Do not carry too much luggage on the scooter. An overloaded scoot- er is unstable. Use a strong cord to secure any luggage to the carrier (if equipped). A loose load will af- fect the stability of the scooter and could divert your attention from the road. (See page 1-5.)

U1TS12E0 7

1-7

SAFETY INFORMATION scooter will not bounce excessive- ly during transport.

EAU57600

Further safe-riding points Be sure to signal clearly when

making turns. Braking can be extremely difficult

on a wet road. Avoid hard braking, because the scooter could slide. Apply the brakes slowly when stopping on a wet surface.

Slow down as you approach a cor- ner or turn. Once you have com- pleted a turn, accelerate slowly.

Be careful when passing parked cars. A driver might not see you and open a door in your path.

Railroad crossings, streetcar rails, iron plates on road construction sites, and manhole covers be- come extremely slippery when wet. Slow down and cross them with caution. Keep the scooter up- right, otherwise it could slide out from under you.

The brake pads or linings could get wet when you wash the scooter. After washing the scooter, check the brakes before riding.

Always wear a helmet, gloves, trousers (tapered around the cuff

1

2

DESCRIPTION EAU10411

6

nt (page 3-10)

U1TS12E0 1

Le

1

2

3

4

5

6

7

8

2-1

ft view

5432

1

9

8 7

. Front turn signal light (page 6-24)

. Luggage hook (page 3-12)

. Helmet holder (page 3-9)

. Rear storage compartment (page 3-10)

. Fuel tank cap (page 3-6)

. Rear turn signal light (page 6-24)

. Air filter (page 6-13)

. Battery (page 6-21)

9. Front storage compartme

D

1

2

3

4

5

6

7

8

9

EAU10421

R

5

1

2

3

4

5

6

7

8

U1TS12E0 2

ESCRIPTION

2-2

ight view

4321

8

7 6

. Tail/brake light (page 6-24)

. Carrier (page 3-11)

. Seat (page 3-9)

. Coolant reservoir (page 6-12)

. Headlight (page 6-23)

. Spark plug (page 6-7)

. Centerstand (page 6-19)

. Muffler (page 3-8)

DESCRIPTION

2

3

4

5

6

7

8

9

EAU10431

C

5

6

1

2

3

4

5

6

7

8

U1TS12E0 3

2-3

ontrols and instruments

4321

8 7

9

. Rear brake lever (page 3-5)

. Left handlebar switches (page 3-4)

. Speedometer unit (page 3-3)

. Right handlebar switches (page 3-4)

. Front brake lever (page 3-5)

. Throttle grip (page 6-14)

. Rear wheel lock lever (page 3-5)

. Main switch/steering lock (page 3-1)

9. Fuel gauge (page 3-3)

1

2

3

4

5

6

7

8

9

lock the steering

. Turn the handlebars all the way to the left.

. Push the key in from the OFF po- sition, and then turn it to LOCK while still pushing it.

. Remove the key.

Push.

1

U1TS12E0 1

IN

Ma

Th the use pos

ON All pow com ed.

TIP Th eng

3-1

STRUMENT AND CONTROL FUNCTIONS EAU10462

in switch/steering lock

e main switch/steering lock controls ignition and lighting systems, and is d to lock the steering. The various itions are described below.

EAU10611

electrical circuits are supplied with er, the taillight and meter lighting e on, and the engine can be start-

The key cannot be removed.

e headlight comes on as soon as the ine is started.

EAU10662

OFF All electrical systems are off. The key can be removed.

WARNING EWA10062

Never turn the key to OFF or LOCK while the vehicle is moving. Otherwise the electrical systems will be switched off, which may result in loss of control or an accident.

EAU10685

LOCK The steering is locked, and all electrical systems are off. The key can be re- moved.

To

1

2

3

1.

NTROL FUNCTIONS

2

3

4

5

6

7

8

9

T

P O

EAU11447

olant temperature warning light

is warning light comes on if the en- e overheats. If this occurs, stop the gine immediately and allow the en- e to cool. e electrical circuit of the warning light n be checked by turning the key to N. The warning light should come for a few seconds, and then go off. he warning light does not come on ially when the key is turned to ON, if the warning light remains on, have amaha dealer check the electrical

cuit.

OTICE ECA10022

not continue to operate the en- e if it is overheating.

For radiator-fan-equipped vehi- cles, the radiator fan(s) automati- cally switch on or off according to the coolant temperature in the ra- diator. If the engine overheats, see page

1

2

U1TS12E0 2

INSTRUMENT AND CO

3-2

o unlock the steering

ush the key in, and then turn it to FF while still pushing it.

EAU1100A

Indicator lights and warning light

EAU11021

Turn signal indicator light This indicator light flashes when the turn signal switch is pushed to the left or right.

EAU11081

High beam indicator light This indicator light comes on when the high beam of the headlight is switched on.

Co Th gin en gin Th ca O on If t init or a Y cir

N

Do gin

TIP

. Turn.

. Release.

1 2

1. High beam indicator light

2. Coolant temperature warning light

3. Engine trouble warning light

4. Turn signal indicator light

1

4 3

2

IN

1

2

3

4

5

6

7

8

9

En Th an gin cu se Th ca O on If ini or a cir

EAU12151

el gauge

fuel gauge indicates the amount of l in the fuel tank. The needle moves ards E (Empty) as the fuel level reases. When the needle reaches red line, refuel as soon as possible.

not allow the fuel tank to empty itself pletely.

Fuel gauge

1

U1TS12E0 3

STRUMENT AND CONTROL FUNCTIONS

3-3

6-27 for further instructions.

EAUT1935

gine trouble warning light is warning light flashes or stays on if electrical circuit monitoring the en- e is not working correctly. If this oc- rs, have a Yamaha dealer check the lf-diagnosis system. e electrical circuit of the warning light n be checked by turning the key to N. The warning light should come for a few seconds, and then go off. the warning light does not come on tially when the key is turned to ON, if the warning light remains on, have Yamaha dealer check the electrical cuit.

EAUT1822

Speedometer unit

The speedometer unit is equipped with a speedometer and an odometer. The speedometer shows the riding speed. The odometer shows the total distance traveled.

Fu

The fue tow dec the

TIP Do com

1. Speedometer

2. Odometer

12

1.

NTROL FUNCTIONS

2

3

4

5

6

7

8

9

H

L

R

nt or rear brake to crank the engine h the starter. See page 5-1 for start- instructions prior to starting the en- e.

1

2

3

1

2

U1TS12E0 4

INSTRUMENT AND CO

3-4

EAU1234H

andlebar switches

eft

ight

EAU12401

Dimmer switch / Set this switch to for the high beam and to for the low beam.

EAU12461

Turn signal switch / To signal a right-hand turn, push this switch to . To signal a left-hand turn, push this switch to . When re- leased, the switch returns to the center position. To cancel the turn signal lights, push the switch in after it has re- turned to the center position.

EAU12501

Horn switch Press this switch to sound the horn.

EAU12661

Engine stop switch / Set this switch to before starting the engine. Set this switch to to stop the engine in case of an emergen- cy, such as when the vehicle overturns or when the throttle cable is stuck.

EAUM1133

Start switch Push this switch while applying the

fro wit ing gin

. Dimmer switch /

. Turn signal switch /

. Horn switch

. Engine stop switch /

. Start switch

1

2 3

1

2

IN

1

2

3

4

5

6

7

8

9

Fr

Th rig fro th

EAUT1552

ar wheel lock en the rear wheel lock lever is pulled n to lock the rear wheel, a cover will e over the main switch keyhole to

p prevent theft.

lock . Place the vehicle on the center-

stand. . Lock the steering. (See page 3-1.) . Remove the key from the main

switch. . Pull the rear wheel lock lever

downward, and then release it. The rear wheel will lock and the main switch keyhole will be cov-

1

Rear wheel lock lever

Rear wheel lock release

1 2

**

U1TS12E0 5

STRUMENT AND CONTROL FUNCTIONS

3-5

EAU12902

ont brake lever

e front brake lever is located on the ht side of the handlebar. To apply the nt brake, pull this lever toward the

rottle grip.

EAU12952

Rear brake lever

The rear brake lever is located on the left side of the handlebar. To apply the rear brake, pull this lever toward the handlebar grip.

Re Wh dow clos hel

To 1

2 3

4

. Front brake lever

1

1. Rear brake lever

1

1.

2.

ZAUM00

NTROL FUNCTIONS

2

3

4

5

6

7

8

9

T If to sl a

T In re cl a o

e fuel tank cap cannot be installed less the key is in the lock. In addition, key cannot be removed if the cap is t properly installed and locked.

WARNING EWA10132

ke sure that the fuel tank cap is perly installed before riding.

aking fuel is a fire hazard.

U1TS12E0 6

INSTRUMENT AND CO

3-6

ered.

IP the rear wheel lock lever is not easy pull downward, rotate the rear wheel ightly, and then try pulling the lever gain.

o unlock sert the key into the rear wheel lock lease, push it in, and then turn it ockwise. The rear wheel will unlock nd the main switch keyhole cover will pen.

EAU32485

Fuel tank cap

To remove the fuel tank cap Slide the lock cover open, insert the key into the lock, and then turn it 1/4 turn clockwise. The lock will be released and the fuel tank cap can be removed.

To install the fuel tank cap 1. Insert the fuel tank cap into the

tank opening with the key inserted in the lock and with the marks on the cap and tank aligned.

2. Turn the key counterclockwise to the original position, remove it, and then close the lock cover.

TIP Th un the no

Ma pro Le

1. Fuel tank cap lock cover

2. Match marks

1

2

IN

1

2

3

4

5

6

7

8

9

Fu M th

Ga ex an ris th

r eyes, see your doctor immedi- ly. If gasoline spills on your skin, sh with soap and water. If gaso- spills on your clothing, change r clothes.

EAU36084

TICE ECA11401

only unleaded gasoline. The use eaded gasoline will cause severe

age to internal engine parts, h as the valves and piston rings,

well as to the exhaust system.

r Yamaha engine has been de- ed to use unleaded gasoline with a p octane number [(R+M)/2] of 86 or

her, or a research octane number of r higher. If knocking (or pinging) oc-

s, use a gasoline of a different brand remium unleaded fuel. Use of un- ed fuel will extend spark plug life

ecommended fuel Unleaded gasoline only

uel tank capacity: 4.6 L (1.22 US gal, 1.01 Imp.gal)

U1TS12E0 7

STRUMENT AND CONTROL FUNCTIONS

3-7

EAU13213

el ake sure there is sufficient gasoline in e tank.

WARNING EWA10882

soline and gasoline vapors are tremely flammable. To avoid fires d explosions and to reduce the k of injury when refueling, follow ese instructions.

1. Before refueling, turn off the en- gine and be sure that no one is sit- ting on the vehicle. Never refuel while smoking, or while in the vi- cinity of sparks, open flames, or other sources of ignition such as the pilot lights of water heaters and clothes dryers.

2. Do not overfill the fuel tank. Stop filling when the fuel reaches the bottom of the filler tube. Because fuel expands when it heats up, heat from the engine or the sun can cause fuel to spill out of the fuel tank.

3. Wipe up any spilled fuel immedi- ately. NOTICE: Immediately wipe off spilled fuel with a clean, dry, soft cloth, since fuel may deteri- orate painted surfaces or plastic parts.[ECA10072]

4. Be sure to securely close the fuel tank cap.

WARNING EWA15152

Gasoline is poisonous and can cause injury or death. Handle gaso- line with care. Never siphon gaso- line by mouth. If you should swallow some gasoline or inhale a lot of gas- oline vapor, or get some gasoline in

you ate wa line you

NO

Use of l dam suc as

You sign pum hig 91 o cur or p lead

1. Fuel tank filler tube

2. Maximum fuel level

1 2

R

F

NTROL FUNCTIONS

2

3

4

5

6

7

8

9

a

G T h in e te o re ca o

irable damage to the catalytic nverter.

U1TS12E0 8

INSTRUMENT AND CO

3-8

nd reduce maintenance costs.

asohol here are two types of gasohol: gaso- ol containing ethanol and that contain- g methanol. Gasohol containing thanol can be used if the ethanol con- nt does not exceed 10% (E10). Gas- hol containing methanol is not commended by Yamaha because it n cause damage to the fuel system

r vehicle performance problems.

EAU13446

Catalytic converters This vehicle is equipped with catalytic converters in the exhaust system.

WARNING EWA10863

The exhaust system is hot after op- eration. To prevent a fire hazard or burns: Do not park the vehicle near

possible fire hazards such as grass or other materials that easily burn.

Park the vehicle in a place where pedestrians or children are not likely to touch the hot exhaust system.

Make sure that the exhaust sys- tem has cooled down before do- ing any maintenance work.

Do not allow the engine to idle more than a few minutes. Long idling can cause a build-up of heat.

NOTICE ECA10702

Use only unleaded gasoline. The use of leaded gasoline will cause unre-

pa co

IN

1

2

3

4

5

6

7

8

9

Se

To

TI Do ke L

EAU14302

lmet holder

helmet holder is located under the t.

secure a helmet to the helmet der . Open the seat. (See page 3-9.) . Attach the helmet to the helmet

holder, and then securely close the seat. WARNING! Never ride with a helmet attached to the helmet holder, since the helmet may hit objects, causing loss of control and possibly an accident.[EWA10162]

Helmet holder

1

U1TS12E0 9

STRUMENT AND CONTROL FUNCTIONS

3-9

EAUT1504

at

open the seat 1. Place the scooter on the center-

stand. 2. Insert the key into the main switch,

and then turn it counterclockwise to the first OPEN position. If the main switch is in the LOCK posi- tion, turn the key counterclockwise to the second OPEN position.

P not push inward when turning the y from OFF to OPEN or from OCK to OPEN.

3. Fold the seat up.

To close the seat 1. Fold the seat down, and then push

it down to lock it in place. 2. Remove the key from the main

switch if the scooter will be left un- attended.

TIP Make sure that the seat is properly se- cured before riding.

He

The sea

To hol

1 2

1.

NTROL FUNCTIONS

2

3

4

5

6

7

8

9

T m O th se

nt storage compartment

WARNING EWA11192

Do not exceed the load limit of 1.5 kg (3 lb) for the front storage compartment. Do not exceed the maximum load of 91 kg (201 lb) for the ve- hicle.

Front storage compartment

1

U1TS12E0 10

INSTRUMENT AND CO

3-10

o release the helmet from the hel- et holder pen the seat, remove the helmet from e helmet holder, and then close the at.

EAUT1718

Storage compartments

NOTICE ECA17841

Keep the following points in mind when using the storage compart- ments. Since the storage compart-

ments accumulate heat when exposed to the sun and/or the engine heat, do not store any- thing susceptible to heat, con- sumables or flammable items inside them.

To avoid humidity from spread- ing through the storage com- partments, wrap wet articles in a plastic bag before storing them in the compartments.

Since the storage compart- ments may get wet while the ve- hicle is being washed, wrap any articles stored in the compart- ments in a plastic bag.

Do not keep anything valuable or breakable in the storage com- partments.

Fro

1.

IN

1

2

3

4

5

6

7

8

9

Re

Th ed

TI

EAU15113

rrier

WARNING EWA10172

Do not exceed the load limit of 3 kg (7 lb) for the carrier. Do not exceed the maximum load of 91 kg (201 lb) for the ve- hicle.

1

Rear carrier

1

U1TS12E0 11

STRUMENT AND CONTROL FUNCTIONS

3-11

ar storage compartment

e rear storage compartment is locat- under the seat. (See page 3-9.)

WARNING EWAT1052

Do not exceed the load limit of 5 kg (11 lb) for the rear storage compartment. Do not exceed the maximum load of 91 kg (201 lb) for the ve- hicle.

P Some helmets cannot be stored in the storage compartment because of their size or shape. Do not leave your scooter unat-

tended with the seat open. Ca

. Rear storage compartment

1

1.

NTROL FUNCTIONS

2

3

4

5

6

7

8

9

L

1

U1TS12E0 12

INSTRUMENT AND CO

3-12

EAUT1073

uggage hook

WARNING EWAT1032

Do not exceed the load limit of 1 kg (2 lb) for the luggage hook.

Do not exceed the maximum load of 91 kg (201 lb) for the ve- hicle.

. Luggage hook

1

1

2

3

4

5

6

7

8

9

EAU15598

ndition. Always follow the inspection

EWA11152

accident or equipment damage. ed by the procedures provided in

PAGE

3-7

6-9

6-11

6-12

6-16, 6-18

6-18, 6-17

U1TS12E0 1

FO

Ins and

Fa Do thi

Be

Fu

En

Fi

Co

Fr

Re

4-1

R YOUR SAFETY PRE-OPERATION CHECKS

pect your vehicle each time you use it to make sure the vehicle is in safe operating co maintenance procedures and schedules described in the Owners Manual.

WARNING

ilure to inspect or maintain the vehicle properly increases the possibility of an not operate the vehicle if you find any problem. If a problem cannot be correct s manual, have the vehicle inspected by a Yamaha dealer.

fore using this vehicle, check the following points:

ITEM CHECKS

el Check fuel level in fuel tank. Refuel if necessary. Check fuel line for leakage.

gine oil Check oil level in engine. If necessary, add recommended oil to specified level. Check vehicle for oil leakage.

nal transmission oil Check vehicle for oil leakage.

olant Check coolant level in reservoir. If necessary, add recommended coolant to specified level. Check cooling system for leakage.

ont brake

Check operation. Lubricate cable if necessary. Check lever free play. Adjust if necessary.

ar brake

Check operation. Lubricate cable if necessary. Check lever free play. Adjust if necessary.

PERATION CHECKS

2

3

4

5

6

7

8

9

T ricate cable 6-14, 6-19

W 6-15, 6-16

B 6-19

C 6-19

C

I a

E 3-4

PAGE

U1TS12E0 2

FOR YOUR SAFETY PRE-O

4-2

hrottle grip

Make sure that operation is smooth. Check throttle grip free play. If necessary, have Yamaha dealer adjust throttle grip free play and lub

and grip housing.

heels and tires

Check for damage. Check tire condition and tread depth. Check air pressure. Correct if necessary.

rake levers Make sure that operation is smooth. Lubricate lever pivoting points if necessary.

enterstand Make sure that operation is smooth. Lubricate pivot if necessary.

hassis fasteners Make sure that all nuts, bolts and screws are properly tightened. Tighten if necessary.

nstruments, lights, signals nd switches

Check operation. Correct if necessary.

ngine stop switch Check operation.

ITEM CHECKS

1

2

3

4

5

6

7

8

9

EAUT1514

rting a cold engine

TICE ECA10251

page 5-3 for engine break-in in- ctions prior to operating the ve-

le for the first time.

. Turn the key to ON and make sure that the engine stop switch is set to .

. Close the throttle completely.

. Start the engine by pushing the start switch while applying the front or rear brake. If the engine does not start, re- lease the start switch, wait a few seconds, and then try again. Each starting attempt should be as short as possible to preserve the bat- tery. Do not crank the engine more than 10 seconds on any one at- tempt. If the engine does not start, try with the throttle open 1/8 turn.

TICE ECA11043

maximum engine life, never ac- erate hard when the engine is d!

U1TS12E0 1

O

Re bec the und

Fa the tro or

5-1

PERATION AND IMPORTANT RIDING POINTS EAU15952

ad the Owners Manual carefully to ome familiar with all controls. If re is a control or function you do not erstand, ask your Yamaha dealer.

WARNING EWA10272

ilure to familiarize yourself with controls can lead to loss of con- l, which could cause an accident injury.

EAU45311

TIP This model is equipped with a lean an- gle sensor to stop the engine in case of a turnover. To start the engine after a turnover, be sure to turn the main switch to OFF and then to ON. Fail- ing to do so will prevent the engine from starting even though the engine will crank when pushing the start switch.

Sta

NO

See stru hic

1

2 3

NO

For cel col

ANT RIDING POINTS

2

3

4

5

6

7

8

9

S EAU16794

aking

WARNING EWA10301

Avoid braking hard or suddenly (especially when leaning over to one side), otherwise the scooter may skid or overturn. Railroad crossings, streetcar rails, iron plates on road con- struction sites, and manhole covers become extremely slip- pery when wet. Therefore, slow down when approaching such areas and cross them with cau- tion. Keep in mind that braking on a wet road is much more difficult. Ride slowly down a hill, as brak- ing downhill can be very diffi- cult.

. Close the throttle completely.

. Apply both front and rear brakes simultaneously while gradually in- creasing the pressure.

U1TS12E0 2

OPERATION AND IMPORT

5-2

EAU16771

tarting off 1. While pulling the rear brake lever

with your left hand and holding the carrier with your right hand, push the scooter off the centerstand.

2. Sit astride the seat, and then ad- just the rear view mirrors.

3. Switch the turn signal on. 4. Check for oncoming traffic, and

then slowly turn the throttle grip (on the right) in order to take off.

5. Switch the turn signal off.

EAU16782

Acceleration and deceleration

The speed can be adjusted by opening and closing the throttle. To increase the speed, turn the throttle grip in direction (a). To reduce the speed, turn the throt- tle grip in direction (b).

Br

1 2

(b)

(a)

(a)

(b)

O

1

2

3

4

5

6

7

8

9

Ti co Fu yo tip

500 km (90300 mi) id prolonged operation above 1/2 ttle. the engine freely through the rs, but do not use full throttle at any

e.

1000 km (300600 mi) id prolonged operation above 3/4 ttle. NOTICE: After 1000 km (600 of operation, the engine oil must changed and the oil strainer

aned.[ECA10352]

0 km (600 mi) and beyond id prolonged full-throttle operation. y the speed occasionally.

TICE ECA10271

ny engine trouble should occur ing the engine break-in period, ediately have a Yamaha dealer

ck the vehicle.

U1TS12E0 3

PERATION AND IMPORTANT RIDING POINTS

5-3

EAU16821

ps for reducing fuel nsumption el consumption depends largely on ur riding style. Consider the following s to reduce fuel consumption:

Avoid high engine speeds during acceleration. Avoid high engine speeds with no load on the engine. Turn the engine off instead of let- ting it idle for an extended length of time (e.g., in traffic jams, at traffic lights or at railroad crossings).

EAU16831

Engine break-in There is never a more important period in the life of your engine than the period between 0 and 1000 km (600 mi). For this reason, you should read the follow- ing material carefully. Since the engine is brand new, do not put an excessive load on it for the first 1000 km (600 mi). The various parts in the engine wear and polish themselves to the correct operating clearances. During this period, prolonged full-throt- tle operation or any condition that might result in engine overheating must be avoided.

EAU16953

0150 km (090 mi) Avoid prolonged operation above 1/3 throttle. After every hour of operation, stop the engine, and then let it cool for five to ten minutes. Vary the engine speed from time to time. Do not operate the engine at one set throttle position.

150 Avo thro Rev gea tim

500 Avo thro mi) be cle

100 Avo Var

NO

If a dur imm che

ANT RIDING POINTS

2

3

4

5

6

7

8

9

P W th sw

ZA

U1TS12E0 4

OPERATION AND IMPORT

5-4

EAU17214

arking hen parking, stop the engine, and en remove the key from the main itch.

WARNING EWA10312

Since the engine and exhaust system can become very hot,

park in a place where pedestri- ans or children are not likely to touch them and be burned.

Do not park on a slope or on soft ground, otherwise the vehicle may overturn, increasing the risk of a fuel leak and fire.

Do not park near grass or other flammable materials which might catch fire.

UM00**

1

2

3

4

5

6

7

8

9

EAU17303

ission controls not only function to ure cleaner air, but are also vital to per engine operation and maximum formance. In the following periodic intenance charts, the services relat- to emissions control are grouped arately. These services require cialized data, knowledge, and ipment. Maintenance, replacement, epair of the emission control devic- and systems may be performed by repair establishment or individual t is certified (if applicable). Yamaha lers are trained and equipped to form these particular services.

U1TS12E0 1

PE

Pe bric saf sib cle poi me the Th ma con nor pen gra the be

Fa hic tiv yo ser yo vic ser

6-1

RIODIC MAINTENANCE AND ADJUSTMENT EAU17245

riodic inspection, adjustment, and lu- ation will keep your vehicle in the est and most efficient condition pos- le. Safety is an obligation of the vehi- owner/operator. The most important nts of vehicle inspection, adjust- nt, and lubrication are explained on following pages. e intervals given in the periodic intenance charts should be simply sidered as a general guide under mal riding conditions. However, de- ding on the weather, terrain, geo- phical location, and individual use, maintenance intervals may need to shortened.

WARNING EWA10322

ilure to properly maintain the ve- le or performing maintenance ac- ities incorrectly may increase ur risk of injury or death during vice or while using the vehicle. If

u are not familiar with vehicle ser- e, have a Yamaha dealer perform vice.

WARNING EWA15123

Turn off the engine when performing maintenance unless otherwise specified. A running engine has moving

parts that can catch on body parts or clothing and electrical parts that can cause shocks or fires.

Running the engine while ser- vicing can lead to eye injury, burns, fire, or carbon monoxide poisoning possibly leading to death. See page 1-4 for more in- formation about carbon monox- ide.

WARNING EWA15461

Brake discs, calipers, drums, and linings can become very hot during use. To avoid possible burns, let brake components cool before touching them.

Em ens pro per ma ed sep spe equ or r es any tha dea per

AND ADJUSTMENT

2

3

4

5

6

7

8

9

EAU48451

T rting from 4000 mi (7000 km) or 12

Yamaha dealer perform the service.

U1TS12E0 2

PERIODIC MAINTENANCE

6-2

IP From 12000 mi (19000 km) or 36 months, repeat the maintenance intervals sta

months. Items marked with an asterisk require special tools, data and technical skills, have a

P

1

2

3

4

5

6

7

8

9

EAU17562

Pe

N

OMETER READINGS

)

s

6000 mi (10000

km) or

18 months

8000 mi (13000

km) or

24 months

10000 mi (16000

km) or

30 months

1

2 Replace.

3 ry 6000 mi (10000 km)

4

5

6

7

U1TS12E0 3

ERIODIC MAINTENANCE AND ADJUSTMENT

6-3

riodic maintenance chart for the emission control system

o. ITEM ROUTINE

INITIAL OD

600 mi (1000 km)

or 1 month

2000 mi (4000 km)

or 6 months

4000 mi (7000 km

or 12 month

* Fuel line Check fuel hoses for cracks or

damage. Replace if necessary.

Spark plug

Check condition. Adjust gap and clean. Replace at 4000 mi (7000 km) or

12 months and thereafter every 4000 mi (6000 km) or 12 months.

Replace.

* Valve clearance Check and adjust valve clearance when engine is cold. Eve

* Crankcase breather system

Check breather hose for cracks or damage.

Replace if necessary.

* Fuel injection Check engine idle speed.

* Exhaust system Check for leakage. Tighten if necessary. Replace gasket(s) if necessary.

* Air induction system

Check the air cut-off valve, reed valve, and hose for damage.

Replace any damaged parts.

AND ADJUSTMENT

2

3

4

5

6

7

8

9

EAU32129

G

N

OMETER READINGS

i )

s

6000 mi (10000

km) or

18 months

8000 mi (13000

km) or

24 months

10000 mi (16000

km) or

30 months

1 2

3

4

5

6

7

8 Repack.

U1TS12E0 4

PERIODIC MAINTENANCE

6-4

eneral maintenance and lubrication chart

o. ITEM ROUTINE

INITIAL OD

600 mi (1000 km)

or 1 month

2000 mi (4000 km)

or 6 months

4000 m (7000 km

or 12 month

Air filter element Replace. Air filter check hose Clean.

* Front brake Check operation. Adjust cable and replace brake

shoes if necessary.

* Rear brake Check operation. Adjust cable and replace brake

shoes if necessary.

* Wheels Check runout and for damage. Replace if necessary.

* Tires

Check tread depth and for damage.

Replace if necessary. Check air pressure. Correct if necessary.

* Wheel bearings Check bearings for smooth

operation. Replace if necessary.

* Steering bearings

Check bearing assemblies for looseness.

Moderately repack with lithium-soap-based grease every 8000 mi (13000 km) or 24 months.

P

1

2

3

4

5

6

7

8

9

9

10

11

12

13

14

15

16

17

y 3 years

18

19 mi (10000 km)

20

N

OMETER READINGS

)

s

6000 mi (10000

km) or

18 months

8000 mi (13000

km) or

24 months

10000 mi (16000

km) or

30 months

U1TS12E0 5

ERIODIC MAINTENANCE AND ADJUSTMENT

6-5

* Chassis fasteners Check all chassis fitting and

fasteners. Correct if necessary.

Front brake lever pivot shaft

Apply lithium-soap-based grease lightly.

Rear brake lever pivot shaft

Apply lithium-soap-based grease lightly.

Centerstand Check operation. Lubricate.

* Front fork Check operation and for oil

leakage. Replace if necessary.

* Shock absorber assembly

Check operation and for oil leakage.

Replace if necessary.

Engine oil

Change (warm engine before draining).

Check oil level and vehicle for oil leakage.

Engine oil strainer Clean.

* Cooling system Check coolant level and vehicle

for coolant leakage.

Change coolant. Ever Final transmission oil

Check vehicle for oil leakage. Change.

* V-belt Replace. Every 6250

* Front and rear brake switches Check operation.

o. ITEM ROUTINE

INITIAL OD

600 mi (1000 km)

or 1 month

2000 mi (4000 km)

or 6 months

4000 mi (7000 km

or 12 month

AND ADJUSTMENT

2

3

4

5

6

7

8

9

EAUT3371

T A

ich must not be cleaned with com-

ly wet or dusty areas.

2

2

2

N

OMETER READINGS

i )

s

6000 mi (10000

km) or

18 months

8000 mi (13000

km) or

24 months

10000 mi (16000

km) or

30 months

U1TS12E0 6

PERIODIC MAINTENANCE

6-6

IP ir filter This models air filter is equipped with a disposable oil-coated paper element, wh

pressed air to avoid damaging it. The air filter element needs to be replaced more frequently when riding in unusual

1 * Control and meter cables

Apply Yamaha cable lubricant or other suitable cable lubricant thoroughly.

2 * Throttle grip

Check operation. Check throttle grip free play, and

adjust if necessary. Lubricate cable and grip housing.

3 * Lights, signals and switches

Check operation. Adjust headlight beam.

o. ITEM ROUTINE

INITIAL OD

600 mi (1000 km)

or 1 month

2000 mi (4000 km)

or 6 months

4000 m (7000 km

or 12 month

P

1

2

3

4

5

6

7

8

9

R pa Th to job th to

EAUT1484

ecking the spark plug

spark plug is an important engine ponent, which is easy to check.

ce heat and deposits will cause any rk plug to slowly erode, the spark

g should be removed and checked ccordance with the periodic mainte- ce and lubrication chart. In addition, condition of the spark plug can re- l the condition of the engine.

remove the spark plug . Remove panel A. (See page 6-7.) . Remove the partition between the

battery and the spark plug by pull- ing it up.

. Remove the spark plug cap.

1

Partition

1

U1TS12E0 7

ERIODIC MAINTENANCE AND ADJUSTMENT

6-7

EAU18752

emoving and installing the nel e panel shown needs to be removed

perform some of the maintenance s described in this chapter. Refer to

is section each time the panel needs be removed and installed.

EAU19282

Panel A

To remove the panel Remove the screw, and then pull the panel off as shown.

To install the panel Place the panel in the original position, and then install the screw.

Ch

The com Sin spa plu in a nan the vea

To 1 2

3

. Panel A

1

1. Panel A

1

1.

AND ADJUSTMENT

2

3

4

5

6

7

8

9

T

T If fe a d st th

T

torque wrench is not available when talling a spark plug, a good estimate the correct torque is 1/41/2 turn st finger tight. However, the spark g should be tightened to the speci- d torque as soon as possible.

. Install the spark plug cap.

. Install the partition and the panel.

U1TS12E0 8

PERIODIC MAINTENANCE

6-8

4. Remove the spark plug as shown, with a spark plug wrench available at a Yamaha dealer.

o check the spark plug 1. Check that the porcelain insulator

around the center electrode of the spark plug is a medium-to-light tan (the ideal color when the vehicle is ridden normally).

IP the spark plug shows a distinctly dif- rent color, the engine could be oper- ting improperly. Do not attempt to iagnose such problems yourself. In- ead, have a Yamaha dealer check e vehicle.

2. Check the spark plug for electrode erosion and excessive carbon or other deposits, and replace it if necessary.

o install the spark plug 1. Measure the spark plug gap with a

wire thickness gauge and, if nec-

essary, adjust the gap to specifica- tion.

2. Clean the surface of the spark plug gasket and its mating surface, and then wipe off any grime from the spark plug threads.

3. Install the spark plug with the spark plug wrench, and then tight- en it to the specified torque.

TIP If a ins of pa plu fie

4 5

Specified spark plug: NGK/CR7E

1. Spark plug gap

Spark plug gap: 0.70.8 mm (0.0280.031 in)

Tightening torque: Spark plug:

13 Nm (1.3 mkgf, 9.4 ftlbf)

1

P

1

2

3

4

5

6

7

8

9

En Th be m cle pe ch

To

off. . Place an oil pan under the engine

to collect the used oil. . Remove the engine oil filler cap

and the engine oil drain bolts A and B to drain the oil from the crankcase. NOTICE: When re- moving the engine oil drain bolt B, the O-ring, compression spring, and oil strainer will fall out. Take care not to lose these parts.[ECAT1022]

Engine oil drain bolt A

1

U1TS12E0 9

ERIODIC MAINTENANCE AND ADJUSTMENT

6-9

EAUT1463

gine oil and oil strainer e engine oil level should be checked fore each ride. In addition, the oil ust be changed and the oil strainer aned at the intervals specified in the riodic maintenance and lubrication art.

check the engine oil level 1. Place the vehicle on the center-

stand. A slight tilt to the side can result in a false reading.

2. Start the engine, warm it up for several minutes, and then turn it off.

3. Wait a few minutes until the oil set- tles, remove the oil filler cap, wipe the dipstick clean, insert it back into the oil filler hole (without screwing it in), and then remove it again to check the oil level.

TIP The engine oil should be between the minimum and maximum level marks.

4. If the engine oil is below the mini- mum level mark, add sufficient oil of the recommended type to raise it to the correct level.

5. Insert the dipstick into the oil filler hole, and then tighten the oil filler cap.

To change the engine oil and clean the oil strainer

1. Start the engine, warm it up for several minutes, and then turn it

2

3

1. Oil filler cap

2. Maximum level mark

3. Minimum level

2

1

3

1.

AND ADJUSTMENT

2

3

4

5

6

7

8

9 T M se

OTICE ECA11671

Do not use oils with a diesel specification of CD or oils of a higher quality than specified. In addition, do not use oils labeled ENERGY CONSERVING II or higher. Be sure no foreign material en- ters the crankcase.

. Start the engine, and then let it idle for several minutes while checking it for oil leakage. If oil is leaking, im- mediately turn the engine off and check for the cause.

. Turn the engine off, and then check the oil level and correct it if necessary.

1

2

3

4

U1TS12E0 10

PERIODIC MAINTENANCE

6-10

4. Clean the oil strainer with solvent, and then check it for damage and replace it if necessary.

5. Check the O-ring for damage and replace it if necessary.

6. Install the oil strainer, compression spring, O-ring and engine oil drain bolt B.

IP ake sure that the O-ring is properly ated.

7. Install engine oil drain bolt A, and then tighten both drain bolts to

their specified torques.

8. Refill with the specified amount of the recommended engine oil, and then install and tighten the oil filler cap.

N

9

10

. Engine oil drain bolt B

. O-ring

. Compression spring

. Strainer

1234

1

Tightening torque: Engine oil drain bolt A:

23 Nm (2.3 mkgf, 16.6 ftlbf) Engine oil drain bolt B:

32 Nm (3.2 mkgf, 23.1 ftlbf)

1. Oil filler hole

Recommended engine oil: See page 8-1.

Oil change quantity: 0.78 L (0.82 US qt, 0.69 Imp.qt)

1

P

1

2

3

4

5

6

7

8

9

Fi Th ch rid Ya sc sio th m . Check the final transmission case

for oil leakage. If oil is leaking, check for the cause.

ightening torque: Final transmission oil filler bolt:

23 Nm (2.3 mkgf, 17 ftlbf)

ecommended final transmission il: See page 8-1.

il quantity: 0.10 L (0.11 US qt, 0.09 Imp.qt)

U1TS12E0 11

ERIODIC MAINTENANCE AND ADJUSTMENT

6-11

EAUT1563

nal transmission oil e final transmission case must be ecked for oil leakage before each e. If any leakage is found, have a maha dealer check and repair the ooter. In addition, the final transmis- n oil must be changed as follows at

e intervals specified in the periodic aintenance and lubrication chart. 1. Start the engine, warm it up by rid-

ing the scooter for several min- utes, and then stop the engine.

2. Place the scooter on the center- stand.

3. Place an oil pan under the final transmission case to collect the used oil.

4. Remove the oil filler bolt and drain bolt to drain the oil from the final transmission case.

5. Install the final transmission oil drain bolt, and then tighten it to the specified torque.

6. Refill with the specified amount of the recommended final transmis- sion oil, and then install the oil filler bolt and tighten it to the specified torque. WARNING! Make sure that no foreign material enters the final transmission case. Make sure that no oil gets on the tire or wheel.[EWA11312]

7 1. Final transmission oil filler bolt

2. Final transmission oil drain bolt

Tightening torque: Final transmission oil drain bolt:

13 Nm (1.3 mkgf, 9.4 ftlbf)

2 1

T

R o

O

AND ADJUSTMENT

2

3

4

5

6

7

8

9

C T b a sp a

T T fo th te n

T

. Add coolant or distilled water to raise the coolant to the maximum level mark, and install the coolant reservoir cap and the panel. NOTICE: If coolant is not avail- able, use distilled water or soft tap water instead. Do not use hard water or salt water since it is harmful to the engine. If water has been used instead of cool- ant, replace it with coolant as soon as possible, otherwise the cooling system will not be pro- tected against frost and corro- sion. If water has been added to the coolant, have a Yamaha dealer check the antifreeze con-

Coolant reservoir cap

1

U1TS12E0 12

PERIODIC MAINTENANCE

6-12

EAU20071

oolant he coolant level should be checked efore each ride. In addition, the cool- nt must be changed at the intervals ecified in the periodic maintenance

nd lubrication chart.

EAUT1527

o check the coolant level he coolant level should be checked as llows before each ride. In addition, e coolant must be changed at the in- rvals specified in the periodic mainte- ance and lubrication chart. 1. Place the vehicle on the center-

stand.

IP The coolant level must be checked

on a cold engine since the level varies with engine temperature.

Make sure that the vehicle is posi- tioned straight up when checking the coolant level. A slight tilt to the side can result in a false reading.

2. Check the coolant level in the cool- ant reservoir.

TIP The coolant should be between the minimum and maximum level marks.

3. If the coolant is at or below the minimum level mark, remove pan- el A and the reservoir cap. (See page 6-7.) WARNING! Remove only the coolant reservoir cap. Never attempt to remove the ra- diator cap when the engine is hot.[EWA15162]

4

1. Maximum level mark

2. Minimum level mark

1

2

1.

P

1

2

3

4

5

6

7

8

9

Ch Th te na Ya W th ho

removing the screws. . Pull the air filter element out. . Insert a new air filter element into

the air filter case as shown. NOTICE: Make sure that the air filter element is properly seated in the air filter case. The engine should never be operated with- out the air filter element in- stalled, otherwise the piston(s) and/or cylinder(s) may become excessively worn.[ECA10482]

. Install the air filter case cover by in- stalling the screws.

clean the air filter check hose . Check the hose on the side of the

air filter case for accumulated dirt or water.

. If dirt or water is visible, remove the hose, clean it, and then install it.

U1TS12E0 13

ERIODIC MAINTENANCE AND ADJUSTMENT

6-13

tent of the coolant as soon as possible, otherwise the effec- tiveness of the coolant will be reduced.[ECA10473]

EAU33032

anging the coolant e coolant must be changed at the in-

rvals specified in the periodic mainte- nce and lubrication chart. Have a maha dealer change the coolant. ARNING! Never attempt to remove e radiator cap when the engine is t.[EWA10382]

EAUT1492

Replacing the air filter element and cleaning the check hose

The air filter element should be re- placed at the intervals specified in the periodic maintenance and lubrication chart. Replace the air filter element more frequently if you are riding in un- usually wet or dusty areas. In addition, the air filter check hose must be fre- quently checked and cleaned if neces- sary.

To replace the air filter element 1. Remove the air filter case cover by

2 3

4

To 1

2

Coolant reservoir capacity: 0.26 L (0.27 US qt, 0.23 Imp.qt)

1. Air filter case cover

2. Air filter element

3. Air filter check hose

1 2 3

AND ADJUSTMENT

2

3

4

5

6

7

8

9

C s C n Y

EAU21402

lve clearance e valve clearance changes with use, ulting in improper air-fuel mixture d/or engine noise. To prevent this m occurring, the valve clearance st be adjusted by a Yamaha dealer

the intervals specified in the periodic intenance and lubrication chart.

U1TS12E0 14

PERIODIC MAINTENANCE

6-14

EAU44735

hecking the engine idling peed heck the engine idling speed and, if ecessary, have it corrected by a amaha dealer.

EAU21385

Checking the throttle grip free play The throttle grip free play should mea- sure 1.53.5 mm (0.060.14 in) at the inner edge of the throttle grip. Periodi- cally check the throttle grip free play and, if necessary, have a Yamaha dealer adjust it.

Va Th res an fro mu at ma

Engine idling speed: 20002200 r/min

P

1

2

3

4

5

6

7

8

9

Ti Ti ve dit sm is co at fie

Ti Th an rid

Ne tio ca

sidewall is cracked, have a Yamaha ler replace the tire immediately.

information s vehicle is equipped with tubeless s. s age, even if they have not been d or have only been used occasion- . Cracking of the tread and sidewall ber, sometimes accompanied by cass deformation, is an evidence of ing. Old and aged tires shall be cked by tire specialists to ascertain ir suitability for further use. r extensive tests, only the tires list-

below have been approved for this del by Yamaha.

inimum tire tread depth (front and ear):

1.0 mm (0.04 in)

U1TS12E0 15

ERIODIC MAINTENANCE AND ADJUSTMENT

6-15

EAUT4260

res res are the only contact between the hicle and the road. Safety in all con- ions of riding depends on a relatively all area of road contact. Therefore, it

essential to maintain the tires in good ndition at all times and replace them the appropriate time with the speci- d tires.

re air pressure e tire air pressure should be checked d, if necessary, adjusted before each e.

WARNING EWA10512

ver overload your vehicle. Opera- n of an overloaded vehicle could use an accident.

Tire inspection

The tires must be checked before each ride. If a tire tread shows crosswise lines (minimum tread depth), if the tire has a nail or glass fragments in it, or if

the dea

Tire Thi tire Tire use ally rub car age che the Afte ed mo

Tire air pressure* (measured on cold tires):

Front: 150 kPa (1.50 kgf/cm2, 22 psi)

Rear: 175 kPa (1.75 kgf/cm2, 25 psi)

Maximum load*: 91 kg (201 lb)

* Total weight of rider, cargo and ac- cessories

1. Tire sidewall

2. Tire wear indicator

3. Tire tread depth

M r

AND ADJUSTMENT

2

3

4

5

6

7

8

9

EAU22132

justing the brake lever free ay

e brake lever free play should mea- re 10.020.0 mm (0.390.79 in) as own. Periodically check the brake le- r free play and, if necessary, adjust it follows. increase the brake lever free play, n the brake lever free play adjusting t at the brake shoe plate in direction . To decrease the brake lever free y, turn the adjusting nut in direction .

Front brake lever free play

1

U1TS12E0 16

PERIODIC MAINTENANCE

6-16

WARNING EWA10581

It is dangerous to ride with a worn-out tire. When a tire tread begins to show crosswise lines, have a Yamaha dealer replace the tire immediately.

The replacement of all wheel- and brake-related parts, includ- ing the tires, should be left to a Yamaha dealer, who has the necessary professional knowl- edge and experience to do so.

Ride at moderate speeds after changing a tire since the tire surface must first be broken in for it to develop its optimal characteristics.

EAU21963

Cast wheels To maximize the performance, durabil- ity, and safe operation of your vehicle, note the following points regarding the specified wheels. The wheel rims should be checked

for cracks, bends, warpage or oth- er damage before each ride. If any damage is found, have a Yamaha dealer replace the wheel. Do not attempt even the smallest repair to the wheel. A deformed or cracked wheel must be replaced.

The wheel should be balanced whenever either the tire or wheel has been changed or replaced. An unbalanced wheel can result in poor performance, adverse han- dling characteristics, and a short- ened tire life.

Ad pl

Th su sh ve as To tur nu (a) pla (b)

Front tire: Size:

90/90-10 41J Manufacturer/model:

MAXXIS / C-922 Rear tire:

Size: 90/90-10 41J

Manufacturer/model: MAXXIS / C-922

1.

P

1

2

3

4

5

6

7

8

9

If ta de

WARNING EWA10651

roper adjustment cannot be ob- ed as described, have a Yamaha ler make this adjustment.

1 Adjusting nut

1(b)

(a)

U1TS12E0 17

ERIODIC MAINTENANCE AND ADJUSTMENT

6-17

WARNING EWA10651

proper adjustment cannot be ob- ined as described, have a Yamaha aler make this adjustment.

EAU22171

Adjusting the rear brake lever free play

The brake lever free play should mea- sure 10.020.0 mm (0.390.79 in) as shown. Periodically check the brake le- ver free play and, if necessary, adjust it as follows. To increase the brake lever free play, turn the adjusting nut at the brake shoe plate in direction (a). To decrease the brake lever free play, turn the adjusting nut in direction (b).

If p tain dea

. Adjusting nut

(a)

(b)

1

1. Rear brake lever free play

1

1.

AND ADJUSTMENT

2

3

4

5

6

7

8

9

C b

F

R

EAU23098

ecking and lubricating the bles e operation of all control cables and condition of the cables should be

ecked before each ride, and the ca- s and cable ends should be lubricat- if necessary. If a cable is damaged does not move smoothly, have a maha dealer check or replace it. RNING! Damage to the outer

using of cables may result in in- nal rusting and cause interfer- ce with cable movement. Replace maged cables as soon as possi- to prevent unsafe condi- ns.[EWA10712]

1

2

1

2

ecommended lubricant: Yamaha cable lubricant or other suit- able cable lubricant

U1TS12E0 18

PERIODIC MAINTENANCE

6-18

EAU22363

hecking the front and rear rake shoes

ront

ear

The front and rear brake shoes must be checked for wear at the intervals spec- ified in the periodic maintenance and lubrication chart. Each brake is provid- ed with a wear indicator, which allows you to check the brake shoe wear with- out having to disassemble the brake. To check the brake shoe wear, check the position of the wear indicator while applying the brake. If a brake shoe has worn to the point that the wear indicator reaches the wear limit line, have a Yamaha dealer replace the brake shoes as a set.

Ch ca Th the ch ble ed or Ya WA ho ter en da ble tio

. Wear indicator

. Wear limit line

. Wear indicator

. Wear limit line

1

2

1

2

R

P

1

2

3

4

5

6

7

8

9

C th Th be tio Ya fie Th ru is co co en wa wh or a

EAU23193

ecking and lubricating the nterstand operation of the centerstand uld be checked before each ride, the pivots and metal-to-metal con-

t surfaces should be lubricated if essary.

WARNING EWA11302

e centerstand does not move up down smoothly, have a Yamaha ler check or repair it. Otherwise, centerstand could contact the und and distract the operator, re- ting in a possible loss of control.

ecommended lubricant: Lithium-soap-based grease

U1TS12E0 19

ERIODIC MAINTENANCE AND ADJUSTMENT

6-19

EAU23115

hecking and lubricating the rottle grip and cable e operation of the throttle grip should checked before each ride. In addi- n, the cable should be lubricated by a maha dealer at the intervals speci- d in the periodic maintenance chart. e throttle cable is equipped with a

bber cover. Make sure that the cover securely installed. Even though the ver is installed correctly, it does not mpletely protect the cable from water try. Therefore, use care not to pour ter directly onto the cover or cable en washing the vehicle. If the cable

cover becomes dirty, wipe clean with moist cloth.

EAU43634

Lubricating the front and rear brake levers The pivoting points of the front and rear brake levers must be lubricated at the intervals specified in the periodic main- tenance and lubrication chart.

Ch ce The sho and tac nec

If th and dea the gro sul

Recommended lubricant: Lithium-soap-based grease

R

AND ADJUSTMENT

2

3

4

5

6

7

8

9

C T fo in te

T C ce

T

EAU45512

ecking the steering rn or loose steering bearings may

use danger. Therefore, the operation the steering must be checked as fol- s at the intervals specified in the pe-

dic maintenance and lubrication art. . Place the vehicle on the center-

stand. WARNING! To avoid inju- ry, securely support the vehicle so there is no danger of it falling over.[EWA10752]

. Hold the lower ends of the front fork legs and try to move them for- ward and backward. If any free play can be felt, have a Yamaha dealer check or repair the steering.

U1TS12E0 20

PERIODIC MAINTENANCE

6-20

EAU51951

hecking the front fork he condition and operation of the front rk must be checked as follows at the tervals specified in the periodic main- nance and lubrication chart.

o check the condition heck the front fork for damage and ex- ssive oil leakage.

o check the operation 1. Place the vehicle on a level sur-

face and hold it in an upright posi- tion. WARNING! To avoid injury, securely support the vehicle so there is no danger of it falling over.[EWA10752]

2. While applying the front brake, push down hard on the handlebars several times to check if the front fork compresses and rebounds smoothly.

NOTICE ECA10591

If any damage is found or the front fork does not operate smoothly, have a Yamaha dealer check or re- pair it.

Ch Wo ca of low rio ch

1

2

P

1

2

3

4

5

6

7

8

9

C Th be th tio hu sm th

lowing FIRST AID. EXTERNAL: Flush with plenty

of water. INTERNAL: Drink large quan-

tities of water or milk and im- mediately call a physician.

EYES: Flush with water for 15 minutes and seek prompt medical attention.

Batteries produce explosive hy- drogen gas. Therefore, keep sparks, flames, cigarettes, etc., away from the battery and pro- vide sufficient ventilation when charging it in an enclosed space. KEEP THIS AND ALL BATTER- IES OUT OF THE REACH OF CHILDREN.

TICE ECA10621

er attempt to remove the battery l seals, as this would permanent- amage the battery.

battery is located under the foot- rd. Remove panel A to access the tery. (See page 6-7.)

U1TS12E0 21

ERIODIC MAINTENANCE AND ADJUSTMENT

6-21

EAU23292

hecking the wheel bearings e front and rear wheel bearings must checked at the intervals specified in

e periodic maintenance and lubrica- n chart. If there is play in the wheel b or if the wheel does not turn oothly, have a Yamaha dealer check

e wheel bearings.

EAUT1235

Battery

This model is equipped with a VRLA (Valve Regulated Lead Acid) battery. There is no need to check the electro- lyte or to add distilled water. However, the battery lead connections need to be checked and, if necessary, tightened.

WARNING EWA10761

Electrolyte is poisonous and dangerous since it contains sul- furic acid, which causes severe burns. Avoid any contact with skin, eyes or clothing and al- ways shield your eyes when working near batteries. In case of contact, administer the fol-

NO

Nev cel ly d

The boa bat

1. Battery

1

AND ADJUSTMENT

2

3

4

5

6

7

8

9

T H te h b if e

N

T L s q c

T

EAUT1242

placing the fuse

e fuse holder is located beside the ttery. Remove panel A to access the e. (See page 6-7.) he fuse is blown, replace it as fol- s. . Turn the key to OFF and turn off

all electrical circuits. . Remove the blown fuse, and then

install a new fuse of the specified amperage. WARNING! Do not use a fuse of a higher amperage rating than recommended to avoid causing extensive dam- age to the electrical system and possibly a fire.[EWA15132]

Fuse

1

U1TS12E0 22

PERIODIC MAINTENANCE

6-22

o charge the battery ave a Yamaha dealer charge the bat- ry as soon as possible if it seems to ave discharged. Keep in mind that the attery tends to discharge more quickly the vehicle is equipped with optional

lectrical accessories.

OTICE ECA16522

o charge a VRLA (Valve Regulated ead Acid) battery, a special (con- tant-voltage) battery charger is re- uired. Using a conventional battery harger will damage the battery.

o store the battery 1. If the vehicle will not be used for

more than one month, remove the battery, fully charge it, and then place it in a cool, dry place. NOTICE: When removing the battery, be sure the key is turned to OFF, then discon- nect the negative lead before disconnecting the positive lead.[ECA16303]

2. If the battery will be stored for more than two months, check it at least

once a month and fully charge it if necessary.

3. Fully charge the battery before in- stallation. NOTICE: When install- ing the battery, be sure the key is turned to OFF, then con- nect the positive lead before connecting the negative lead.[ECA16841]

4. After installation, make sure that the battery leads are properly con- nected to the battery terminals.

NOTICE ECA16531

Always keep the battery charged. Storing a discharged battery can cause permanent battery damage.

Re

Th ba fus If t low

1

2

1.

P

1

2

3

4

5

6

7

8

9

. Disconnect the headlight coupler, and then remove the headlight bulb cover.

. Remove the headlight bulb holder by turning it counterclockwise, and

Headlight unit

Headlight coupler

Bulb cover

1

1

U1TS12E0 23

ERIODIC MAINTENANCE AND ADJUSTMENT

6-23

3. Turn the key to ON and turn on the electrical circuits to check if the devices operate.

4. If the fuse immediately blows again, have a Yamaha dealer check the electrical system.

EAU23787

Replacing the headlight bulb This model is equipped with a halogen bulb headlight. If the headlight bulb burns out, replace it as follows.

NOTICE ECA10651

Take care not to damage the follow- ing parts: Headlight bulb

Do not touch the glass part of the headlight bulb to keep it free from oil, otherwise the transpar- ency of the glass, the luminosity of the bulb, and the bulb life will be adversely affected. Thor- oughly clean off any dirt and fin- gerprints on the headlight bulb using a cloth moistened with al- cohol or thinner.

Headlight lens Do not affix any type of tinted film or stickers to the headlight lens. Do not use a headlight bulb of a wattage higher than specified.

1. Remove the headlight unit by re- moving the screws.

2

3

Specified fuse: 15.0 A

1.

1.

2.

2

AND ADJUSTMENT

2

3

4

5

6

7

8

9

EAU24205

placing a turn signal light lb . Remove the turn signal light lens

by removing the screw.

1

Turn signal light lens

Bulb

Turn signal light lens

Bulb

1

2

2 1

U1TS12E0 24

PERIODIC MAINTENANCE

6-24

then remove the burnt-out bulb.

4. Place a new headlight bulb into po- sition, and then secure it with the bulb holder.

5. Install the headlight bulb cover, and then connect the coupler.

6. Install the headlight unit by install- ing the screws.

7. Have a Yamaha dealer adjust the headlight beam if necessary.

EAU24135

Replacing the tail/brake light bulb

1. Remove the tail/brake light lens by removing the screws.

2. Remove the burnt-out bulb by pushing it in and turning it counter- clockwise.

3. Insert a new bulb into the socket, push it in, and then turn it clock- wise until it stops.

4. Install the lens by installing the screws. NOTICE: Do not over- tighten the screws, otherwise the lens may break.[ECA10682]

Re bu

1

. Headlight bulb holder

1

1. Tail/brake light lens

2. Bulb

2

1

1.

2.

1.

2.

P

1

2

3

4

5

6

7

8

9

ters or furnaces. Gasoline or oline vapors can ignite or ex- de, causing severe injury or perty damage.

U1TS12E0 25

ERIODIC MAINTENANCE AND ADJUSTMENT

6-25

2. Remove the burnt-out bulb by pushing it in and turning it counter- clockwise.

3. Insert a new bulb into the socket, push it in, and then turn it clock- wise until it stops.

4. Install the lens by installing the screw. NOTICE: Do not over- tighten the screw, otherwise the lens may break.[ECA11192]

EAU25882

Troubleshooting Although Yamaha scooters receive a thorough inspection before shipment from the factory, trouble may occur dur- ing operation. Any problem in the fuel, compression, or ignition systems, for example, can cause poor starting and loss of power. The following troubleshooting charts represent quick and easy procedures for checking these vital systems your- self. However, should your scooter re- quire any repair, take it to a Yamaha dealer, whose skilled technicians have the necessary tools, experience, and know-how to service the scooter prop- erly. Use only genuine Yamaha replace- ment parts. Imitation parts may look like Yamaha parts, but they are often inferi- or, have a shorter service life and can lead to expensive repair bills.

WARNING EWA15142

When checking the fuel system, do not smoke, and make sure there are no open flames or sparks in the ar- ea, including pilot lights from water

hea gas plo pro

AND ADJUSTMENT

2

3

4

5

6

7

8

9

EAU42706

T

S

s not start. ry.

hicle.

ehicle.

engine does not start. eck the compression.

erate the electric starter.

The engine does not start. Check the ignition.

U1TS12E0 26

PERIODIC MAINTENANCE

6-26

roubleshooting charts

tarting problems or poor engine performance

Check the fuel level in the fuel tank.

1. Fuel There is enough fuel.

There is no fuel.

Check the battery.

Supply fuel. The engine doe Check the batte

Operate the electric starter.

4. Compression There is compression.

There is no compression.

The engine does not start. Have a Yamaha dealer check the ve

Have a Yamaha dealer check the v

Remove the spark plug and check the electrodes.

3. Ignition Wipe off with a dry cloth and correct the spark plug gap, or replace the spark plug.

Have a Yamaha dealer check the vehicle. The Ch

Operate the electric starter.

2. Battery The engine turns over quickly.

The engine turns over slowly.

The battery is good.

Dry

Wet Op

Check the battery lead connections, and have a Yamaha dealer charge the battery if necessary.

P

1

2

3

4

5

6

7

8

9

En EWAT1041

ding hot fluid and steam may be until the engine has cooled.

cap counterclockwise to the de- stopped, press down on the cap

TI If c anged to the recommended coolant as

Have a Yamaha dealer check and repair the cooling system.

Add coolant. (See TIP.)

f the engine overheats again, have a eck and repair the cooling system.

is e.

is age.

U1TS12E0 27

ERIODIC MAINTENANCE AND ADJUSTMENT

6-27

gine overheating

WARNING

Do not remove the radiator cap when the engine and radiator are hot. Scal blown out under pressure, which could cause serious injury. Be sure to wait Place a thick rag, like a towel, over the radiator cap, and then slowly rotate the tent to allow any residual pressure to escape. When the hissing sound has while turning it counterclockwise, and then remove the cap.

P oolant is not available, tap water can be temporarily used instead, provided that it is ch soon as possible.

Wait until the engine has cooled.

Check the coolant level in the reservoir and radiator.

The coolant level is OK.

The coolant level is low. Check the cooling system for leakage.

Start the engine. I Yamaha dealer ch

There leakag

There no leak

2

3

4

5

6

7

8

9

ARE AND STORAGE ucts onto seals, gaskets and wheel axles. Always rinse the dirt and de- greaser off with water.

aning

OTICE ECA10784

Avoid using strong acidic wheel cleaners, especially on spoked wheels. If such products are used on hard-to-remove dirt, do not leave the cleaner on the af- fected area any longer than in- structed. Also, thoroughly rinse the area off with water, immedi- ately dry it, and then apply a cor- rosion protection spray. Improper cleaning can damage plastic parts (such as cowlings, panels, windshields, headlight lenses, meter lenses, etc.) and the mufflers. Use only a soft, clean cloth or sponge with wa- ter to clean plastic. However, if the plastic parts cannot be thor- oughly cleaned with water, di- luted mild detergent with water may be used. Be sure to rinse off any detergent residue using

U1TS12E0 1

M

N

So m su ad fo br cl th th be is

7-1

SCOOTER C EAU37834

atte color caution

OTICE ECA15193

me models are equipped with atte colored finished parts. Be re to consult a Yamaha dealer for vice on what products to use be- re cleaning the vehicle. Using a ush, harsh chemical products or eaning compounds when cleaning ese parts will scratch or damage eir surface. Wax also should not applied to any matte colored fin-

hed parts.

EAU26096

Care While the open design of a scooter re- veals the attractiveness of the technol- ogy, it also makes it more vulnerable. Rust and corrosion can develop even if high-quality components are used. A rusty exhaust pipe may go unnoticed on a car, however, it detracts from the overall appearance of a scooter. Fre- quent and proper care does not only comply with the terms of the warranty, but it will also keep your scooter looking good, extend its life and optimize its performance.

Before cleaning 1. Cover the muffler outlet with a

plastic bag after the engine has cooled down.

2. Make sure that all caps and covers as well as all electrical couplers and connectors, including the spark plug cap, are tightly in- stalled.

3. Remove extremely stubborn dirt, like oil burnt onto the crankcase, with a degreasing agent and a brush, but never apply such prod-

Cle

N

S

1

2

3

4

5

6

7

8

9

ain well into spring.

. Clean the scooter with cold water and a mild detergent after the en- gine has cooled down. NOTICE: Do not use warm water since it increases the corrosive action of the salt.[ECA10792]

. Apply a corrosion protection spray on all metal, including chrome- and nickel-plated, surfaces to prevent corrosion.

aning the windshield id using any alkaline or strong acid ner, gasoline, brake fluid, or any

er solvent. Clean the windshield with oth or sponge dampened with a mild ergent, and then wash it off thor- hly with water. For additional clean- use Yamaha Windshield Cleaner another high-quality windshield ner. Some cleaning compounds for

stics may leave scratches on the dshield. Before using such clean- , test an area of the windshield ch does not affect your visibility and ch cannot be easily recognized.

U1TS12E0 2

COOTER CARE AND STORAGE

7-2

plenty of water, as it is harmful to plastic parts. Do not use any harsh chemical products on plastic parts. Be sure to avoid using cloths or sponges which have been in contact with strong or abrasive cleaning products, solvent or thinner, fuel (gasoline), rust re- movers or inhibitors, brake flu- id, antifreeze or electrolyte. Do not use high-pressure wash- ers or steam-jet cleaners since they cause water seepage and deterioration in the following ar- eas: seals (of wheel and swing- arm bearings, fork and brakes), electric components (couplers, connectors, instruments, switches and lights), breather hoses and vents. For scooters equipped with a windshield: Do not use strong cleaners or hard sponges as they will cause dulling or scratching. Some cleaning com- pounds for plastic may leave scratches on the windshield. Test the product on a small hid-

den part of the windshield to make sure that it does not leave any marks. If the windshield is scratched, use a quality plastic polishing compound after washing.

After normal use Remove dirt with warm water, a mild detergent, and a soft, clean sponge, and then rinse thoroughly with clean water. Use a toothbrush or bottlebrush for hard-to-reach areas. Stubborn dirt and insects will come off more easily if the area is covered with a wet cloth for a few minutes before cleaning.

After riding in the rain, near the sea or on salt-sprayed roads Since sea salt or salt sprayed on the roads during winter are extremely cor- rosive in combination with water, carry out the following steps after each ride in the rain, near the sea or on salt-sprayed roads.

TIP Salt sprayed on roads in the winter may

rem

1

2

Cle Avo clea oth a cl det oug ing, or clea pla win ers whi whi

ARE AND STORAGE

2

3

4

5

6

7

8

9

A

C c

help remove the moisture from the lens.

U1TS12E0 3

SCOOTER C

7-3

fter cleaning 1. Dry the scooter with a chamois or

an absorbing cloth. 2. Use a chrome polish to shine

chrome, aluminum and stain- less-steel parts, including the ex- haust system. (Even the thermally induced discoloring of stain- less-steel exhaust systems can be removed through polishing.)

3. To prevent corrosion, it is recom- mended to apply a corrosion pro- tection spray on all metal, including chrome- and nickel-plat- ed, surfaces.

4. Use spray oil as a universal clean- er to remove any remaining dirt.

5. Touch up minor paint damage caused by stones, etc.

6. Wax all painted surfaces. 7. Let the scooter dry completely be-

fore storing or covering it.

WARNING EWA10943

ontaminants on the brakes or tires an cause loss of control. Make sure that there is no oil or

wax on the brakes or tires. If necessary, clean the brake

discs and brake linings with a regular brake disc cleaner or ac- etone, and wash the tires with warm water and a mild deter- gent.

Before operating the scooter test its braking performance and cornering behavior.

NOTICE ECA10801

Apply spray oil and wax spar- ingly and make sure to wipe off any excess.

Never apply oil or wax to any rubber and plastic parts, but treat them with a suitable care product.

Avoid using abrasive polishing compounds as they will wear away the paint.

TIP Consult a Yamaha dealer for ad-

vice on what products to use. Washing, rainy weather or humid

climates can cause the headlight lens to fog. Turning the headlight on for a short period of time will

S

1

2

3

4

5

6

7

8

9

St

Sh Al pla ag su te er

N

Lo Be m

. Lubricate all control cables and the pivoting points of all levers and pedals as well as of the sidestand/ centerstand.

. Check and, if necessary, correct the tire air pressure, and then lift the scooter so that both of its wheels are off the ground. Alterna- tively, turn the wheels a little every month in order to prevent the tires from becoming degraded in one spot.

. Cover the muffler outlet with a plastic bag to prevent moisture from entering it.

. Remove the battery and fully charge it. Store it in a cool, dry place and charge it once a month. Do not store the battery in an ex- cessively cold or warm place [less than 0 C (30 F) or more than 30 C (90 F)]. For more information on storing the battery, see page 6-21.

ke any necessary repairs before ing the scooter.

U1TS12E0 4

COOTER CARE AND STORAGE

7-4

EAU36564

orage

ort-term ways store your scooter in a cool, dry ce and, if necessary, protect it ainst dust with a porous cover. Be re the engine and the exhaust sys- m are cool before covering the scoot- .

OTICE ECA10821

Storing the scooter in a poorly ventilated room or covering it with a tarp, while it is still wet, will allow water and humidity to seep in and cause rust. To prevent corrosion, avoid damp cellars, stables (because of the presence of ammonia) and areas where strong chemi- cals are stored.

ng-term fore storing your scooter for several

onths: 1. Follow all the instructions in the

Care section of this chapter.

2. Fill up the fuel tank and add fuel stabilizer (if available) to prevent the fuel tank from rusting and the fuel from deteriorating.

3. Perform the following steps to pro- tect the cylinder, piston rings, etc. from corrosion. a. Remove the spark plug cap

and spark plug. b. Pour a teaspoonful of engine oil

into the spark plug bore. c. Install the spark plug cap onto

the spark plug, and then place the spark plug on the cylinder head so that the electrodes are grounded. (This will limit spark- ing during the next step.)

d. Turn the engine over several times with the starter. (This will coat the cylinder wall with oil.)

e. Remove the spark plug cap from the spark plug, and then install the spark plug and the spark plug cap. WARNING! To prevent damage or injury from sparking, make sure to ground the spark plug elec- trodes while turning the en- gine over.[EWA10952]

4

5

6

7

TIP Ma stor

2

3

4

5

6

7

8

9

SPECIFICATIONS ark plug(s):

anufacturer/model: NGK/CR7E

park plug gap: 0.70.8 mm (0.0280.031 in)

tch: lutch type: Dry, centrifugal automatic

nsmission: rimary reduction ratio:

1.000 inal drive:

Gear econdary reduction ratio:

13.231 (48/13 43/12) ransmission type:

V-belt automatic assis: rame type:

Backbone aster angle: 24.00

rail: 71 mm (2.8 in)

nt tire: ype:

Tubeless ize:

90/90-10 41J anufacturer/model: MAXXIS / C-922

ar tire: ype:

Tubeless

U1TS12E0 1

Di

W

En

8-1

EAU58581mensions: Overall length:

1665 mm (65.6 in) Overall width:

630 mm (24.8 in) Overall height:

1005 mm (39.6 in) Seat height:

715 mm (28.1 in) Wheelbase:

1160 mm (45.7 in) Ground clearance:

85 mm (3.35 in) Minimum turning radius:

1800 mm (70.9 in) eight: Curb weight:

81 kg (179 lb) Technical permissible mass (Maximum load + Curb weight):

172 kg (379 lb) gine: Engine type:

Liquid cooled 4-stroke, SOHC Cylinder arrangement:

Single cylinder Displacement:

49 cm3

Bore stroke: 38.0 43.6 mm (1.50 1.72 in)

Compression ratio: 12.0 : 1

Starting system: Electric starter

Lubrication system: Wet sump

Engine oil: Recommended brand:

YAMALUBE Type:

S

Periodic oil change: 0.78 L (0.82 US qt, 0.69 Imp.qt)

Final transmission oil: Type:

SAE 10W-30 type SE motor oil Quantity:

0.10 L (0.11 US qt, 0.09 Imp.qt) Coolant quantity:

Coolant reservoir (up to the maximum level mark):

0.26 L (0.27 US qt, 0.23 Imp.qt) Radiator (including all routes):

0.26 L (0.27 US qt, 0.23 Imp.qt) Air filter:

Air filter element: Oil-coated paper element

Fuel: Recommended fuel:

Unleaded gasoline only Fuel tank capacity:

4.6 L (1.22 US gal, 1.01 Imp.gal) Fuel injection:

Throttle body: ID mark:

3P31 00

Sp M

S

Clu C

Tra P

F

S

T

Ch F

C

T

Fro T

S

M

Re T

AE 10W-40, 10W-50, 15W-40, 20W-40 or 20W-50

S

1

2

3

4

5

6

7

8

9

Lo

Tir tir

Fr

Re

Fr

Re

ront turn signal light: 12 V, 10.0 W 2

ear turn signal light: 12 V, 10.0 W 2

icense plate light: 12 V, 5.0 W 1 ( Compatible with T/L )

eter lighting: 12 V, 1.7 W 2

igh beam indicator light: 12 V, 1.7 W 1

urn signal indicator light: 12 V, 1.7 W 1

oolant temperature warning light: 14 V, 3.0 W 1

ngine trouble warning light: 12 V, 1.7 W 1

e: use:

15.0 A

U1TS12E0 2

PECIFICATIONS

8-2

Size: 90/90-10 41J

Manufacturer/model: MAXXIS / C-922

ading: Maximum load:

91 kg (201 lb) * (Total weight of rider, cargo and accesso-

ries) e air pressure (measured on cold es):

Front: 150 kPa (1.50 kgf/cm2, 22 psi)

Rear: 175 kPa (1.75 kgf/cm2, 25 psi)

ont wheel: Wheel type:

Cast wheel Rim size:

J10 x 2.15 ar wheel: Wheel type:

Cast wheel Rim size:

J10 x 2.15 ont brake: Type:

Drum brake Operation:

Right hand operation ar brake: Type:

Drum brake

Operation: Left hand operation

Front suspension: Type:

Telescopic fork Spring/shock absorber type:

Coil spring/oil damper Wheel travel:

59 mm (2.3 in) Rear suspension:

Type: Unit swing

Spring/shock absorber type: Coil spring/oil damper

Wheel travel: 54 mm (2.1 in)

Electrical system: Ignition system:

TCI Charging system:

AC magneto Battery:

Model: GTX5L-BS

Voltage, capacity: 12 V, 4.0 Ah

Headlight: Bulb type:

Halogen bulb Bulb voltage, wattage quantity:

Headlight: 12 V, 35.0 W/35.0 W 1

Tail/brake light: 12 V, 5.0 W/21.0 W 1

F

R

L

M

H

T

C

E

Fus F

2

3

4

5

6

7

8

9

MER INFORMATION EAU26441

gine serial number

e engine serial number is stamped o the crankcase.

EAU26461

del label

Engine serial number

Model label

1

1

U1TS12E0 1

Id Re be inf nu Th ed au de de

VE BE

EN

M

9-1

CONSU EAU26357

entification numbers cord the vehicle identification num- r, engine serial number, model label ormation, and the key identification mber in the spaces provided below. ese identification numbers are need- when registering the vehicle with the thorities in your area and when or- ring spare parts from a Yamaha aler.

HICLE IDENTIFICATION NUM- R:

GINE SERIAL NUMBER:

ODEL LABEL INFORMATION:

KEY IDENTIFICATION NUMBER:

EAU26411

Vehicle identification number

The vehicle identification number is stamped into the frame.

TIP The vehicle identification number is used to identify your vehicle and may be used to register it with the licensing authority in your area.

En

Th int

Mo 1. Vehicle identification number

1

1.

1.

C

1

2

3

4

5

6

7

8

9

Th tio th fo sp

Ke

Th sta be re

1

ZAU

U1TS12E0 2

ONSUMER INFORMATION

9-2

e model label is affixed to the loca- n shown. Record the information on is label in the space provided. This in- rmation will be needed when ordering are parts from a Yamaha dealer.

EAU26391

y identification number

e key identification number is mped into the key. Record this num- r in the space provided and use it for ference when ordering a new key.

EAU48271

Vehicle Emission Control Informa- tion label

The Vehicle Emission Control Informa- tion label is affixed at the location in the illustration. This label shows specifica- tions related to exhaust emissions as required by federal law, state law and Environment Canada.

. Key identification number

1

M00**

1. Vehicle Emission Control Information label

1

MER INFORMATION

2

3

4

5

6

7

8

9

EAU26553

R If ury or death, you should immediately in tifying Yamaha Motor Corporation, U that a safety defect exists in a group o ome involved in individual problems b T (TTY: 1-800-424-9153); go to http:// w est Building, Washington, DC 20590. Y car.gov.

U1TS12E0 3

CONSU

9-3

eporting safety defects you believe that your vehicle has a defect which could cause a crash or could cause inj form the National Highway Traffic Safety Administration (NHTSA) in addition to no .S.A. If NHTSA receives similar complaints, it may open an investigation, and if it finds f vehicles, it may order a recall and remedy campaign. However, NHTSA cannot bec etween you, your dealer, or Yamaha Motor Corporation, U.S.A. o contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1-888-327-4236 ww.safercar.gov; or write to: Administrator, NHTSA, 1200 New Jersey Avenue, SE, W ou can also obtain other information about motor vehicle safety from http://www.safer

C

1

2

3

4

5

6

7

8

9

EAU26581

Sc TA Fe ring inoperative by any person other th esign incorporated into any new ve- hic r or while it is in use or (2) the use of th rative by any person. A S LISTED BELOW. Th .

U1TS12E0 4

ONSUMER INFORMATION

9-4

ooter noise regulation MPERING WITH NOISE CONTROL SYSTEM PROHIBITED: deral law prohibits the following acts or the causing thereof: (1) The removal or rende

an for purposes of maintenance, repair, or replacement of any device or element of d le for the purpose of noise control prior to its sale or delivery to the ultimate purchase

e vehicle after such device or element of design has been removed or rendered inope MONG THOSE ACTS PRESUMED TO CONSTITUTE TAMPERING ARE THE ACT ese acts include tampering with the following systems; i.e., modification, removal, etc

Exhaust system Muffler Exhaust pipe Silencer Intake system Air cleaner case Air cleaner element Intake duct

MER INFORMATION

2

3

4

5

6

7

8

9

EAU26601

M C cle will be required to document that m t below is printed only as a reminder th

ler ress Remarks

U1TS12E0 5

CONSU

9-5

aintenance record opies of work orders and/or receipts for parts purchased and installed on your motorcy aintenance has been completed in accordance with the emissions warranty. The char at maintenance work is required. It is not acceptable proof of maintenance work.

Maintenance interval

Date of service Mileage Servicing dea

name and add

600 mi (1000 km) or

1 month 2000 mi

(4000 km) or 6 months 4000 mi

(7000 km) or 12 months 6000 mi

(10000 km) or 18 months 8000 mi

(13000 km) or 24 months 10000 mi

(16000 km) or 30 months 12000 mi

(19000 km) or 36 months 14000 mi

(22000 km) or 42 months 16000 mi

(25000 km) or 48 months

C

1

2

3

4

5

6

7

8

9

ler ess Remarks

U1TS12E0 6

ONSUMER INFORMATION

9-6

18000 mi (28000 km) or

54 months 20000 mi

(31000 km) or 60 months

Maintenance interval

Date of service Mileage Servicing dea

name and addr

MER INFORMATION

2

3

4

5

6

7

8

9

EAU61840

Y SCOOTER LIMITED W

MENT PERIOD cc 12,000 km (7,465 miles)

or five years, whichever occurs first

9cc 18,000 km (11,185 miles) or five years, whichever occurs first

er 30,000 km (18,641 miles) or five years, whichever occurs first

OTOR CORPORATION, U.S.A. MAKES NO RRANTY OF ANY KIND, EXPRESSED OR

ALL IMPLIED WARRANTIES OF TABILITY AND FITNESS FOR A AR PURPOSE WHICH EXCEED THE NS AND TIME LIMITS STATED IN THIS

Y ARE HEREBY DISCLAIMED BY YAMAHA ORPORATION, U.S.A. AND EXCLUDED WARRANTY.

TES DO NOT ALLOW LIMITATIONS ON AN IMPLIED WARRANTY LASTS, SO THE ITATIONS MAY NOT APPLY TO YOU. ALSO FROM THIS WARRANTY ARE ANY L OR CONSEQUENTIAL DAMAGES LOSS OF USE. SOME STATES DO NOT

HE EXCLUSION OR LIMITATION OF L OR CONSEQUENTIAL DAMAGES, SO E EXCLUSION MAY NOT APPLY TO YOU.

RANTY GIVES YOU SPECIFIC LEGAL ND YOU MAY ALSO HAVE OTHER RIGHTS RY FROM STATE TO STATE.

YAMAHA MOTOR CORPORATION, U.S.A. P. O. Box 6555

Cypress, California 90630

U1TS12E0 7

CONSU

9-7

AMAHA MOTOR CORPORATION, U.S.A. 2015 AND LATER MODEL ARRANTY

otor Corporation, U.S.A. hereby warrants that Yamaha scooter purchased from an authorized ooter dealer in the continental United States from defects in material and workmanship for

of time stated herein, subject to certain stated

OD OF WARRANTY for Yamaha scooters e (1) year from the date of purchase, with no

mitation, except for the battery, which is or thirty (30) days from the date of purchase.

EXCLUDED FROM WARRANTY include for non-Yamaha-authorized renting, leasing,

mmercial purposes.

HE PERIOD OF WARRANTY any authorized cooter dealer will, free of charge, repair or Yamahas option, any part adjudged defective due to faulty workmanship or material from

y. Parts used in warranty repairs will be for the balance of the products warranty parts replaced under warranty become the Yamaha Motor Corporation, U.S.A.

EXCLUSIONS from this warranty shall failures caused by:

tion or racing use. on of parts or accessories that are not vely equivalent to genuine Yamaha parts. al strain, neglect, or abuse. proper maintenance and off-season storage ibed in the Owners Manual. t or collision damage. tion to original parts. due to improper transportation.

SPECIFIC EXCLUSIONS from this warranty shall include parts replaced due to normal wear or routine maintenance.

THE CUSTOMERS RESPONSIBILITY under this warranty shall be to:

Operate and maintain the scooter as specified in the appropriate Owners Manual, and

1.

Give notice to an authorized Yamaha scooter dealer of any and all apparent defects within ten (10) days after discovery, and make the machine available at that time for inspection and repairs at such dealers place of business.

2.

WARRANTY TRANSFER: To transfer any remaining warranty from the original purchaser to any subsequent purchaser, it is imperative that the machine be inspected and registered for warranty by an authorized Yamaha scooter dealer. In order for this warranty to remain in effect, this inspection and registration must take place within ten (10) days after transfer. A reasonable dealer- imposed fee may be charged for the inspection.

EMISSIONS CONTROL SYSTEM WARRANTY Yamaha Motor Corporation, U.S.A. also warrants to the ultimate purchaser and each subsequent purchaser of each Yamaha scooter covered by this warranty with a displacement of 50cc or greater, that the vehicle is designed, built, and equipped so as to conform at the time of sale with all U.S. emissions standards applicable at the time of manufacture and that it is free from defects in materials and workmanship which would cause it not to meet these standards within the periods listed immediately below. Failures other than those resulting from defects in material or workmanship which arise solely as a result of owner abuse and/or lack of proper maintenance are not covered by this warranty.

ENGINE DISPLACE 50cc to 169

170cc to 27

280cc or ov

YAMAHA M OTHER WA IMPLIED. MERCHAN PARTICUL OBLIGATIO WARRANT MOTOR C FROM THIS

SOME STA HOW LONG ABOVE LIM EXCLUDED INCIDENTA INCLUDING ALLOW T INCIDENTA THE ABOV

THIS WAR RIGHTS, A WHICH VA

C

1

2

3

4

5

6

7

8

9

U1TS12E0 8

ONSUMER INFORMATION

9-8

MER INFORMATION

2

3

4

5

6

7

8

9

EAU26752

Y ecreation Interruption Protection extra cost. TRIP gives you up to r occurrence for any reasonable because your Yamaha needs ement vehicle rental, emergency n food and lodging when you are

superb coverage goes into effect .S., so it applies to any warranty ered repairs during your entire

ored at any authorized Yamaha

sferable to a new owner if you n make your Yamaha much more

coverage is only available to nd only while your Yamaha is still Warranty period. So visit your to get all the facts. He can show ct your investment with Yamaha

U1TS12E0 9

CONSU

9-9

AMAHA EXTENDED SERVICE (Y.E.S.) Keep your Yamaha protected even after your warranty expires with genuine Yamaha Extended Service (Y.E.S.).

Y.E.S. is designed and administered by Yamaha Motor Corporation to provide maximum owner satisfaction. You get uninterrupted factory-backed coverage for extra peace of mind.

Y.E.S. is flexible. You choose the plan thats right for you: 12 months, 24 months, 36 months or, on certain models, even 48 months beyond your warranty period.

Y.E.S. is designed and administered by the same Yamaha people who handle your warranty and it shows in the comprehensive coverage benefits. There are no mileage limitations. Coverage isnt limited to moving parts or the drive train like many other plans. And Y.E.S. covers manufacturing defects just like the warranty. See the sample contract at your Yamaha dealer to see how comforting uninterrupted factory- backed protection can be.

You dont have to pay anything for covered repairs. Theres no deductible to pay, and repairs arent pro-rated. You dont have any out-of-pocket expenses for covered repairs.

In addition, Travel and R (TRIP) is included at no $250 reimbursement pe expenses you incur covered service: replac towing, phone calls, eve away from home. This when you purchase Y.E repairs as well as cov Y.E.S. plan period.

Y.E.S. coverage is hon dealer nationwide.

Y.E.S. coverage is tran sell or trade-in. That ca valuable!

This excellent Y.E.S. plan Yamaha owners like you, a within the Yamaha Limited authorized Yamaha dealer you how easy it is to prote Extended Service.

C

1

2

3

4

5

6

7

8

9

U1TS12E0 10

ONSUMER INFORMATION

9-10

We urge you to act now. Youll get the excellent benefits of TRIP coverage right away, and youll rest easy knowing youll have strong factory-backed protection even after your Yamaha Limited Warranty expires.

A special note: If visiting your dealer isnt convenient, contact Yamaha with your Primary ID number (your frame number). Well be happy to help you get the Y.E.S. coverage you need.

Yamaha Service Marketing P.O. Box 6555 Cypress, CA 90630 1-(866)-YES-EXTD (1-866-937-3983)

INDEX A

B

C

D

E

F

afe-riding points.......................................1-7 afety defects, reporting............................9-3 afety information......................................1-3 eat ...........................................................3-9 park plug, checking .................................6-7 pecifications.............................................8-1 peedometer unit ......................................3-3 tarting a cold engine ................................5-1 tarting off .................................................5-2 tart switch ................................................3-4 teering, checking ...................................6-20 torage ......................................................7-4 torage compartments ............................3-10

ail/brake light bulb, replacing .................6-24 hrottle grip and cable, checking and lubricating ..............................................6-19 hrottle grip free play, checking...............6-14 ires.........................................................6-15 roubleshooting .......................................6-25 roubleshooting charts ............................6-26 urn signal indicator light...........................3-2 urn signal light bulb, replacing ...............6-24 urn signal switch ......................................3-4

alve clearance .......................................6-14 ehicle Emission Control Information label .........................................................9-2 ehicle identification number.....................9-1

arranty, extended ...................................9-9 arranty, limited........................................9-7 heel bearings, checking........................6-21

U1TS12E0 11

Acceleration and deceleration ...................5-2 Air filter element and check hose,

replacing and cleaning ..........................6-13

Battery .....................................................6-21 Brake lever free play, adjusting ...............6-16 Brake lever, front .......................................3-5 Brake lever, rear ........................................3-5 Brake levers, lubricating ..........................6-19 Brake shoes, checking ............................6-18 Braking ......................................................5-2

Cables, checking and lubricating.............6-18 Care...........................................................7-1 Carrier......................................................3-11 Catalytic converters ...................................3-8 Centerstand, checking and lubricating ....6-19 Coolant ....................................................6-12 Coolant temperature warning light.............3-2

Dimmer switch ...........................................3-4

Engine break-in .........................................5-3 Engine idling speed, checking .................6-14 Engine oil ...................................................6-9 Engine serial number.................................9-1 Engine stop switch.....................................3-4 Engine trouble warning light ......................3-3

Final transmission oil ...............................6-11 Front fork, checking .................................6-20 Fuel............................................................3-7 Fuel consumption, tips for reducing...........5-3

Fuel gauge ................................................ 3-3 Fuel tank cap............................................. 3-6 Fuse, replacing........................................ 6-22

H Handlebar switches................................... 3-4 Headlight bulb, replacing......................... 6-23 Helmet holder............................................ 3-9 High beam indicator light........................... 3-2 Horn switch ............................................... 3-4

I Identification numbers ............................... 9-1 Indicator lights and warning light............... 3-2

K Key identification number.......................... 9-2

L Labels, location ......................................... 1-1 Luggage hook ......................................... 3-12

M Main switch/steering lock .......................... 3-1 Maintenance and lubrication, periodic....... 6-4 Maintenance, emission control system ..... 6-3 Maintenance record .................................. 9-5 Matte color, caution................................... 7-1 Model label................................................ 9-1

N Noise regulation ........................................ 9-4

P Panel, removing and installing .................. 6-7 Parking ...................................................... 5-4 Part locations ............................................ 2-1

R Rear brake lever free play, adjusting ...... 6-17 Rear wheel lock......................................... 3-5

S S S S S S S S S S S S S S

T T T

T T T T T T T

V V V

V W

W W W

IN W

U1TS12E0 12

DEX heels .....................................................6-16

U2PEE0E0 4

U2PEE0E0 3

INDEX EAU55803

For your best ownership experience, think Genuine Yamaha!

Genuine Yamaha Parts Genuine Yamaha replacement parts are the exact same parts as the ones originally equipped on your vehicle, providing you with the performance and durability you have come to expect. Why settle for aftermarket parts that may not provide full confidence and satisfaction?

Genuine Yamaha Accessories Yamaha only offers accessories that meet our high standards for quality and performance. Buy with confidence, knowing your Genuine Yamaha Accessories will fit right and perform right right out of the box.

Yamalube Take care of your Yamaha with legendary Yamalube oils, lubricants, and care products. Theyre formulated and approved by the toughest judges we know: the Yamaha engineering teams that know your Yamaha from the inside out.

Genuine Yamaha Service Manuals Get the same factory manual for your vehicle that the technicians at your authorized Yamaha dealer use. Service manuals are available through your Yamaha dealer or you can order them directly through yamahapubs.com (for US consumers only).

Genuine Yamaha products are available only from your Yamaha dealer.

Find out more at: For US consumers, please visit yamaha-motor.com For Canadian consumers, please visit yamaha-motor.ca

1TS-F8199-12_Cov.indd 3 2014/06/23 14:42:52

Manualsnet FAQs

If you want to find out how the XC50J Yamaha works, you can view and download the Yamaha XC50J Vino 2018 Owner's Manual on the Manualsnet website.

Yes, we have the Owner's Manual for Yamaha XC50J as well as other Yamaha manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Owner's Manual should include all the details that are needed to use a Yamaha XC50J. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Yamaha XC50J Vino 2018 Owner's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Yamaha XC50J Vino 2018 Owner's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Yamaha XC50J Vino 2018 Owner's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Yamaha XC50J Vino 2018 Owner's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Yamaha XC50J Vino 2018 Owner's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.