Contents

Yamaha YAS-71SPX Remote Control Owner's Manual PDF

1 of 44
1 of 44

Summary of Content for Yamaha YAS-71SPX Remote Control Owner's Manual PDF

Front Surround System (CENTER SYSTEM + SUBWOOFER/SYSTEM CONTROL)

YAS-71 (YAS-71CU + YAS-71SPX)

OWNERS MANUAL

UA

1 Read these instructions. 2 Keep these instructions. 3 Heed all warnings. 4 Follow all instructions. 5 Do not use this apparatus near water. 6 Clean only with dry cloth. 7 Do not block any ventilation openings. Install in accordance

with the manufacturers instructions. 8 Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers) that produce heat.

9 Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10 Protect the power cable from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11 Only use attachments/accessories specified by the manufacturer.

12 Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13 Unplug this apparatus during lightning storms or when unused for long periods of time.

14 Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cable or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

IMPORTANT SAFETY INSTRUCTIONS

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

Explanation of Graphical Symbols

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

Note to CATV system installer: This reminder is provided to call the CATV system installers attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

IMPORTANT Please record the serial number of this unit in the space below. MODEL: Serial No.: The serial number is located on the rear of the unit. Retain this Owners Manual in a safe place for future reference.

i En

IMPORTANT SAFETY INSTRUCTIONS

FCC INFORMATION (for US customers)

1 IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.

2 IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA.

3 NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class B digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices.

Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit OFF and ON, please try to eliminate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by the interference.

Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe Ave., Buena Park, CA 90620.

The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.

ii En

1 To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference.

2 Install this sound system in a well ventilated, cool, dry, clean place away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold. Allow ventilation space of at least 5 cm (2) on the top, left, right, and the back of this unit.

3 Locate this unit away from other electrical appliances, motors, or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes from cold to hot, and do not locate this unit in an environment with high humidity (i.e. a room with a humidifier) to prevent condensation inside this unit, which may cause an electrical shock, fire, damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign objects may fall onto this unit and/or this unit may be exposed to liquid dripping or splashing. On the top of this unit, do not place: Other components, as they may cause damage and/or

discoloration on the surface of this unit. Burning objects (i.e. candles), as they may cause fire,

damage to this unit, and/or personal injury. Containers with liquid in them, as they may fall and liquid

may cause electrical shock to the user and/or damage to this unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain, etc. in order not to obstruct heat radiation. If the temperature inside this unit rises, it may cause fire, damage to this unit, and/or personal injury.

7 Do not plug in this unit to a wall outlet until all connections are complete.

8 Do not operate this unit upside-down. It may overheat, possibly causing damage.

9 Do not use force on switches, knobs and/or cords. 10 When disconnecting the power cable from the wall outlet,

grasp the plug; do not pull the cable. 11 Do not clean this unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth. 12 Only voltage specified on this unit must be used. Using this

unit with a higher voltage than specified is dangerous and may cause fire, damage to this unit, and/or personal injury. Yamaha will not be held responsible for any damage resulting from use of this unit with a voltage other than specified.

13 To prevent damage by lightning, keep the power cable and outdoor antennas disconnected from a wall outlet or the unit during a lightning storm.

14 Do not attempt to modify or fix this unit. Contact qualified Yamaha service personnel when any service is needed. The cabinet should never be opened for any reasons.

15 When not planning to use this unit for long periods of time (i.e. vacation), disconnect the AC power plug from the wall outlet.

16 Install this unit near the wall outlet and where the AC power plug can be reached easily.

17 Be sure to read the Troubleshooting section on common operating errors before concluding that this unit is faulty.

18 Before moving this unit, press STANDBY/ON to set this unit in standby mode, and disconnect the power supply cable from the wall outlet.

19 The batteries shall not be exposed to excessive heat such as sunshine, fire or like.

20 Condensation will form when the surrounding temperature changes suddenly. Disconnect the power supply cable from the outlet, then leave the unit alone.

21 Secure placement or installation is the owners responsibility. Yamaha shall not be liable for any accident caused by improper placement or installation of speakers.

22 This unit is not evaluated for wall mounting by CSA.

Yamaha and the Electronic Industries Associations Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or distortion and, most importantly, without affecting your sensitive hearing. Since hearing damage from loud sounds is often undetectable until it is too late, Yamaha and the Electronic Industries Associations Consumer Electronics Group recommend you to avoid prolonged exposure from excessive volume levels.

Caution: Read this before operating your unit.

WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

As long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power source even if you turn off this unit by STANDBY/ON. In this state, this unit is designed to consume a very small quantity of power.

We Want You Listening For A Lifetime

iii En

1 En

IN T

R O

D U

C T

IO N

P R

E P

A R

A T

IO N

B A

S IC

O

P E

R A

T IO

N O

T H

E R

F

U N

C T

IO N

S E

n g

lish U

S E

F U

L

O P

E R

A T

IO N

A D

D IT

IO N

A L

IN

F O

R M

A T

IO N

GETTING STARTED................................................ 2 Supplied parts ................................................................ 2 Controls and functions................................................... 3

PLACING THIS SYSTEM........................................ 8 Placing the center system............................................... 8

CONNECTION......................................................... 11 Connecting the center system and the subwoofer/system

control...................................................................... 11 Connecting external components................................. 12 Connecting the Yamaha iPod universal dock.............. 14 Connecting the Yamaha Bluetooth audio receiver ...... 14 Connecting the indoor FM antenna ............................. 14 Connecting the power cable......................................... 15

BASIC PLAYBACK OPERATION ....................... 16 AIR SURROUND XTREME................................... 17

What is AIR SURROUND XTREME ?...................... 17 Listening to surround mode of AIR SURROUND

XTREME................................................................. 18 Shifting the optimum listening area

from side to side ...................................................... 19 Selecting the optimum listening area........................... 20 Checking the virtual surround effect ........................... 20 Using extended stereo mode........................................ 21 Setting compressed music enhancer ............................ 21

LISTENING TO FM BROADCASTS ....................22 Overview ..................................................................... 22 Controls and functions for the FM tuning ................... 22 Basic tuning operation ................................................. 23 Using station preset feature ......................................... 24

USING OPTIONAL EQUIPMENT ........................27 Using iPod ............................................................... 27 Using Bluetooth components................................... 29

ADJUSTING THE AUDIO DELAY.......................31 LISTENING AT LOW VOLUME (NIGHT

LISTENING MODE)............................................32 ADJUSTING THE VOLUME BALANCE DURING

PLAYBACK ..........................................................32 CHANGING THE BRIGHTNESS OF THE FRONT

PANEL DISPLAY.................................................33

ADDITIONAL INFORMATION ............................34 Troubleshooting........................................................... 34 Glossary ....................................................................... 37 Specifications............................................................... 38

CONTENTS

INTRODUCTION

PREPARATION

BASIC OPERATION

OTHER FUNCTIONS

USEFUL OPERATION

ADDITIONAL INFORMATION

Introduction YAS-71 consists of a center system (YAS-71CU) and subwoofer/system control (YAS-71SPX). This product provides excellent sound with simple operations, allowing you to enjoy various audio sources. We hope the YAS-71 brings you great listening pleasure and satisfaction.

About this manual In this manual, operations that can be performed using either the front panel buttons or remote control are explained

using the remote control. y indicates a tip for your operation. Notes contain important information about safety and operating instructions. This manual is printed prior to production. Design and specifications are subject to change in part as a result of

improvements, etc. In case of differences between the manual and the product, the product has priority.

INTRODUCTION

This product consists of the following items. Before making connections, make sure you received all of the following items.

Units

Accessories

GETTING STARTED

Supplied parts

Center system (YAS-71CU) Subwoofer/system control

(YAS-71SPX)

Front Surround System (CENTER SYSTEM + SUBWOOFER/SYSTEM CONTROL)

YAS-71 (YAS-71CU + YAS-71SPX)

OWNERS MANUAL

UA

System control cable (4 m)

Spacer 2

Remote controlSpeaker cable (4 m) (For US customers only)

Battery 2 (AAA, R03, UM4)

Indoor FM antenna

Mounting template

Double-sided tape (2 pieces) Non-skid pad (2 pieces)

Screw 6

Owners manualCover

Speaker cable (4 m) (For Australian customers only)

2 En

GETTING STARTED E

n g

lish IN

T R

O D

U C

T IO

N

Front panel of the center system

1 Front panel display Shows information about the operational status of the system. ( P. 4)

2 Remote control sensor Receives infrared signals from the remote control. ( P. 5, 7)

3 Power indicator Lights up when the system is turned on. ( P. 16)

4 STANDBY/ON Turns on the system, or sets it to standby mode. ( P. 16)

A small amount of electricity is consumed to receive the infrared signal from the remote control even when the system is in standby mode.

5 INPUT Selects an input source you want to listen to. ( P. 16)

6 VOLUME /+ Controls the volume of the system. ( P. 16)

Controls and functions

Note

3 En

GETTING STARTED

Front panel display of the center system

1 Decoder indicators The respective indicator lights up when any of the decoders of the system is functioning.

2 DOCK indicator Lights up when the system is receiving a signal

from an iPod stationed in the Yamaha iPod universal dock (such as YDS-10 or YDS-11, sold separately) connected to the DOCK terminal of the subwoofer/system control. ( P. 27)

Lights up while the Yamaha Bluetooth audio receiver (such as YBA-10, sold separately) is connected to the Bluetooth component. ( P. 29)

Flashes while the connected Yamaha Bluetooth audio receiver (such as YBA-10, sold separately) and the Bluetooth component are pairing or while the Yamaha Bluetooth audio receiver is searching for the Bluetooth component. ( P. 29)

3 ENHANCER indicator Lights up when compressed music enhancer mode is selected. ( P. 21)

4 NIGHT indicator Lights up when you select night listening mode. ( P. 32)

5 Tuner indicators (AUTO/TUNED/STEREO/ MEMORY)

AUTO indicator Lights up when the system is in automatic tuning mode. ( P. 23)

TUNED indicator Lights up when the system is receiving a station. ( P. 23)

STEREO indicator Lights up when the system is receiving a strong signal from an FM stereo broadcast in automatic tuning mode. ( P. 23)

MEMORY indicator Flashes to show a station can be stored. ( P. 24, 25)

6 Multi information display Shows the selected input source, current surround mode and other information.

7 MUTE indicator/VOLUME indicator Flashes while the mute function is activated.

( P. 16) Indicates the current volume level.

4 En

GETTING STARTED E

n g

lish IN

T R

O D

U C

T IO

N

Remote control 1 Input buttons Select an input source you want to listen to. ( P. 16)

2 STEREO Turns extended stereo mode on and off alternately.

( P. 21) Turns off surround mode. ( P. 18)

3 Cursors ( / / / )/ENTER Position: Change the setting. ( P. 19) Audio delay: Change the setting. ( P. 31) iPod: Move the cursor. ( P. 27) FM: Move a preset group and number forward or backward. ( P. 22)

4 PRESET/TUNE, AUTO/MANL, MEMORY Control an FM tuner. ( P. 22)

5 s / e / p / b / a Control an iPod or a Bluetooth component. ( P. 27, 29)

6 BLUETOOTH ON/BLUETOOTH OFF Connects or disconnects a Bluetooth component. ( P. 30)

7 STANDBY/ON Turns on the system, or sets it to standby mode. ( P. 16)

8 MOVIE/MUSIC/SPORTS/GAME Select surround mode. ( P. 18)

9 VOLUME (+/-)/MUTE Control the volume of the system. ( P. 16)

0 SW (+/-)/CENTER (+/-)/SUR. (+/-) Adjust the volume balance. ( P. 32)

A DOCK MODE Switches operation mode of the iPod. ( P. 27)

Infrared signal transmitter

5 En

GETTING STARTED

B POSITION Shifts the optimum listening area according to your listening position. ( P. 19)

C TEST Outputs the test tone. ( P. 20)

D ENHANCER Turns on and off compressed music enhancer mode alternately. ( P. 21)

E NIGHT Turns night listening mode on or off. ( P. 32)

F AREA Selects the optimum listening area. ( P. 20)

G AUDIO DELAY Delays the output sound to synchronize it with the video image. ( P. 31)

H DISP. MODE Changes the brightness of the front panel display. ( P. 33)

6 En

GETTING STARTED E

n g

lish IN

T R

O D

U C

T IO

N

Using the remote control

Use the remote control within 6 m (20) of the center system and point it toward the remote control sensor.

Be careful not to spill liquid on the remote control. Be careful not to drop the remote control. Do not leave the remote control in a place that is:

hot or humid, such as near a heater or in a bathroom extremely cold dusty

Installing the batteries

If the effective operation distance of the remote control decreases considerably, replace the batteries with two new ones as soon as possible.

Do not use an old battery together with new one. Do not use different types of batteries (for example, alkaline and manganese) together. Their performance will vary, even if they are

similar in shape. If the batteries run out, immediately remove them from the remote control to prevent an explosion or acid leak. Dispose of batteries according to regional regulations. If a battery starts leaking, dispose of it immediately. Be careful not to let leaking battery acid come into contact with your skin or

clothing. Before inserting new batteries, wipe the compartment clean.

Notes

Notes

Within 6 m (20)

1 Take off the battery compartment cover.

2 Insert the 2 supplied batteries (AAA, R03, UM4), observing the polarity markings (+ and ) on the inside of the battery compartment.

3 Snap the battery compartment cover back into place.

7 En

PREPARATION

To enjoy quality sound thoroughly, you need to place this system in the appropriate positions, and install the components correctly. After deciding the layout, follow the procedure below to install this system.

Center system (YAS-71CU) Place the center system beneath a TV or under the TV so that the center system and your TV align vertically. Make sure that the center system is placed in parallel with the wall. Main roles: Produces front channel (stereo) sounds. Also produces virtual center channel sounds (dialogue, etc.) and virtual surround channel sounds effectively using the Yamaha front surround system.

Subwoofer/system control (YAS-71SPX) Place the subwoofer near the center system and turn it slightly toward the center of the room to reduce wall reflections. Main roles: Produces low frequency (LFE) sounds.

This system is shielded against magnetic fields. However, if the picture on your TV screen becomes blurred or distorted, we recommend moving the system away from your TV.

Low frequency sound produced by the subwoofer/system control may be heard differently depending on the listening position and subwoofer location. To enjoy desired sounds, try changing the location of the subwoofer.

Depending on your installation environment, connections to external components can be done before installing this system. We recommend that you temporarily place and arrange all components in order to decide which procedure is best done first.

You can place the center system on a rack or attach it to a wall. Select an installation method that suits your environment.

Placing the center system beneath/under a TV

y If there is any obstacle (TV stand, etc.) under the center system, use the supplied spacers as follows.

1 Attach the supplied double-sided tapes on the spacers and non-skid pads on the rear of the spacers.

2 Attach the spacers to the bottom.

Do not cover the remote control sensor of your TV, etc., by the center system. The spacers may scratch or damage the surface of your rack or floor. Be careful when placing or moving the center system. For your safety, take measures in advance to prevent the center system from falling.

PLACING THIS SYSTEM

Center system (YAS-71CU)

Subwoofer/system control (YAS-71SPX)

Notes

Placing the center system

Example 1: Beneath your TV

Example 2:Under your TV

Side. A Side. B Double- sided tape

Double- sided tape

Non-skid pad Non-skid pad

Notes

8 En

PLACING THIS SYSTEM E

n g

lish P

R E

P A

R A

T IO

N

Attaching the center system to a wall Installing the center system using the keyholes You can attach the center system to a wall using commercially available screws (#8, Diameter: 7.5 mm or more (5/16 or more)).

1 Attach the supplied mounting template on a wall and mark the holes of the mounting template.

2 Remove the mounting template and then install the commercially available screws at the marks.

y To install the cables above the center system, refer to the right column.

3 Hang the center system on the screws using the keyholes on the back of the center system.

When installing the center system on a wall, all installation work must be performed by a qualified contractor or dealer. The customer must never attempt to perform this installation work. Improper or inadequate installation could cause the center system to fall, resulting in personal injury.

Tapes or thumbtacks

Mark

4 to 6 mm (3/16 to 1/4)

Diameter: 7.5 mm or more (#8, 5/16 or more)

Installing the cables above the center system To pass the cables upward, you need to attach the spacers to make room on the back of the center system.

In step 2 of the left column;

2-a: Attach the supplied spacers to the rear panel of the center system using the supplied double-sided tapes. You can choose either the side A or the side B.

2-b: Remove the mounting template and then install the commercially available screws at the marks.

A: For narrow space B: For wide space

Double-sided tape

Double-sided tape

Attach Attach

22 to 24 mm (7/8 to 15/16)

34 to 36 mm (1-5/16 to 1-7/16)

9 En

PLACING THIS SYSTEM

Installing the center system using the screw holes You can also use the inner or outer screw holes on the rear of the center system for installing the center system using a commercially available bracket or rack.

The center system weighs about 5 kg (11 lbs.). Attach the center system to a bracket, rack or wall. Do not attach the center system to a wall that is made of weak materials such as plaster or veneered woods. Doing so may cause the center system to fall.

Use commercially available screws that can support the weight of the installation. Make sure you use specified screws to attach the center system. Using clamps other than specified screws, such as short screws, nails,

or two-sided tape, may cause the center system to fall. When connecting the center system, fix the speaker cables in place where they will not become loose. If your foot or hand accidentally

gets caught on a loose speaker cable, the center system may fall. After attaching the center system, check that the center system is fixed securely. Yamaha will bear no responsibility for any accidents

caused by improper installations.

Screw holes Hole depth: 15 mm (9/16)

Diameter: 6 mm (1/4) Inner pitch: 290 mm (11-7/16) Outer pitch: 550 mm (21-5/8)

550 mm (21-5/8) 290 mm

(11-7/16)

77 mm (3)

52.5 mm (2-1/16)

Bracket or rack, etc.,

15 mm (9/16)

Screw (M6)

Screw hole

Min 7 mm (1/4)

YAS-71CU

Notes

10 En

E n

g lish

P R

E P

A R

A T

IO N

Follow the procedure below to connect the center system and the subwoofer/system control.

Connecting speaker cables

y It is possible to route the supplied speaker cable behind a wall. (For US customers only)

Connecting system control cable

y It is possible to route the supplied system control cable behind a wall. (For US customers only)

CONNECTION

Do not connect the power cable until all connections are completed. Do not use excessive force when inserting the cable plug. Doing so may damage the cable plug and/or

terminal.

Connecting the center system and the subwoofer/system control

Speaker cable (supplied)

Connect the cable plug to the speaker jack of the same color.

Connect the cable plug to the speaker jack of the same color.

System control cable (supplied)

Tighten the screws.

Tighten the screws.

11 En

CONNECTION

The subwoofer/system control has 3 digital input jacks (optical digital 2, coaxial digital 1) and 1 analog input jack. Before connecting your external components, check the output jacks of the components and be sure to use correct connection cables.

Digital connection

The digital jacks of this system support PCM, Dolby Digital, and DTS bitstream. The digital jacks support digital signals of 96 kHz sampling frequency or less.

[INPUT 1, 2] OPTICAL jack Example 1: DVD player

Example 2: TV game console

Connecting external components

Notes

DVD playerTV

Optical digital cable

Game console

TV

Optical digital cable

12 En

CONNECTION E

n g

lish P

R E

P A

R A

T IO

N

[INPUT 3] COAXIAL jack

Analog connection

[INPUT 4] ANALOG jacks Example1: TV

Example 2: VCR or video camera VCR or video camera, etc., with no digital output.

CD player

Coaxial digital cable

TV

Video camera

VCR, etc.

13 En

CONNECTION

The system is equipped with the DOCK terminal, which allows you to connect the Yamaha iPod universal dock (such as YDS-10 or YDS-11, sold separately) where you can dock your iPod. Connect the Yamaha iPod universal dock to the DOCK terminal of the subwoofer/system control using its dedicated cable. Refer to Using iPod on page 27 for details.

You can also connect the Yamaha Bluetooth audio receiver (such as YBA-10, sold separately) to the DOCK terminal. Connect the Yamaha Bluetooth audio receiver to the DOCK terminal of the subwoofer/system control using its dedicated cable. Refer to Using Bluetooth Components on page 29 for details.

To enjoy FM radio broadcasts, connect the supplied indoor FM antenna.

Connecting the Yamaha iPod universal dock

Yamaha iPod universal dock (such as YDS-10 or YDS-11, sold separately)

Connecting the Yamaha Bluetooth audio receiver

Connecting the indoor FM antenna

Yamaha Bluetooth audio receiver (such as YBA-10, sold separately)

Indoor FM antenna (supplied)

y If the radio wave reception is weak in your area or you want to improve the radio wave reception, we recommend that you use an outdoor antenna. For details, consult your nearest authorized Yamaha dealer or Service Center.

14 En

CONNECTION E

n g

lish P

R E

P A

R A

T IO

N

After you have made all connections, connect the power cable of the subwoofer/system control.

y You can attach the cover after you have made all connections or detach according to your preference. Attach the cover to the rear panel of the subwoofer/system control using the 6 supplied screws as shown.

Connecting the power cable

To AC wall outlet

15 En

BASIC OPERATION

Once you have finished all cable connections ( P. 11 to 15) and remote control preparation ( P. 7), follow the procedure below to start basic playback operation.

1 Press STANDBY/ON. This system is turned on and the power indicator lights up. To set the system to standby mode, press STANDBY/ON again.

y This system has the auto-sleep function, which will automatically switch the system to standby mode if the system is left turned on for 24 hours without any operation being performed.

2 Press one of the input buttons to select an input source. For example, if a DVD player is connected to the INPUT 1 jack of the subwoofer/system control, press INPUT 1 to select the DVD player.

y You can also switch the input source by pressing INPUT on the center system repeatedly. The input source changes as follows:

3 Start playback on the selected external component. For information on the external component, refer to the manual for the product.

4 Press VOLUME +/ to adjust the volume level.

y To turn off the volume temporarily, press MUTE. While the mute function is activated, the MUTE indicator flashes. To resume the volume, press MUTE again.

Now, try various features of this system!

BASIC PLAYBACK OPERATION

Using various sound features

To enjoy highly realistic sounds with surround mode P. 18

To shift the optimum listening area from side to side P. 19

To select the optimum listening area P. 20

To experience wider stereo sound when surround mode is not activated P. 21

To play back compressed audio signals with high- quality sound P. 21

To delay the sound output in order to synchronize it with the video image P. 31

To enjoy various input sources at lower volume P. 32

Enjoying FM broadcasts/ optional equipment

To listen to FM broadcasts P. 22

To control iPod playback P. 27

To play back a Bluetooth component P. 29

16 En

E n

g lish

B A

S IC

O

P E

R A

T IO

N

Ordinarily, two front speakers, a center speaker, two surround speakers, and a subwoofer are necessary for enjoying 5.1 channel surround sound.

Virtual 7.1 channel The AIR SURROUND XTREME technology, using only the front left and right speakers of the center system and subwoofer, enables you to enjoy a realistic 7.1 channel sound by simulating sound from virtual speakers at center, surround, and surround backs.

You can check the virtual surround effect and adjust the volume balance according to your preference and the characteristics of your listening room. See the following pages for details.

Checking the virtual surround effect P. 20 Adjusting the volume balance P. 32

Use this feature to adjust the volume balance of the subwoofer, center, and surround channels during playback.

AIR SURROUND XTREME

What is AIR SURROUND XTREME ?

Typical 5.1 channel speaker system

Front speakers

Subwoofer

Center speaker

Surround speakers

The system creates the virtual 7.1 channel surround sound with the center system and the subwoofer/ system control. C: Center virtual speaker FR, FL: Front speakers SW: Subwoofer

SR, SL: Surround virtual speakers SBR, SBL: Surround back virtual speakers

The sound image of the system

17 En

AIR SURROUND XTREME

Press one of the surround mode buttons. The names of the selected input source and the selected surround mode appear in the front panel display.

y To reproduce the original sounds, press STEREO. The system automatically memorizes the settings assigned to

each input source. When you select another input, the system automatically recalls the last settings for the selected input.

Listening to surround mode of AIR SURROUND XTREME

Surround mode buttons

Surround mode descriptions Movie This mode is useful when you enjoy movie contents on media such as DVD, etc. Music This mode is useful when you listen to music contents on media such as DVD, etc. Sports This mode is useful when you enjoy sports programs or TV news. Game This mode is useful when you enjoy video games.

18 En

AIR SURROUND XTREME E

n g

lish B

A S

IC

O P

E R

A T

IO N

This function shifts the optimum listening area from side to side according to your listening position for the best Virtual Surround effect.

1 Press POSITION to enter position mode. The current position appears in the front panel display.

2 Press / to shift the optimum listening area (L6, L5, L4, L3, L2, L1, CENTER, R1, R2, R3, R4, R5, R6). Adjust the optimum listening area from L1 to L6 when your listening position is to the left side of the center system, and adjust the optimum listening area from R1 to R6 when your listening position is to the right side of the center system. The position appears in the front panel display.

Example: POSITION L1

3 Press POSITION again or ENTER to exit position mode.

y The default setting is CENTER. If you press TEST after performing step 1, the system outputs

the test tone for a virtual center speaker so you can adjust the position setting. ( P. 20)

The setting is set for all the input sources. This function is available even when surround mode is off.

If you do not operate this function within 30 seconds after entering position mode, the system automatically exits position mode.

Shifting the optimum listening area from side to side

The optimum listening area Note

19 En

AIR SURROUND XTREME

You can select the optimum listening area from two modes.

Press AREA. Each time you press AREA, NORMAL and WIDE modes change alternately.

NORMAL Select this to sharpen the sound effect.

AREA NORMAL appears in the front panel display when NORMAL mode is selected.

WIDE Select this to widen the optimal listening area.

y The default setting is NORMAL. The setting is set for all the input sources.

This operation is only available when surround mode is activated.

You can check the Virtual Surround effect using test tones produced from the speakers.

Press TEST to output the test tone. The system outputs the test tone and the output channel of the test tone appears in the front panel display.

The output channel of the test tone cycles through as follows. Each channel outputs the test tone for about 2 seconds.

y To cancel test tone mode, press TEST again.

The surround back virtual speaker is included in SL and SR.

Selecting the optimum listening area

AREA

NORMAL WIDE

Note

Checking the virtual surround effect

TEST

Note

Active (virtual) speaker channel

20 En

AIR SURROUND XTREME E

n g

lish B

A S

IC

O P

E R

A T

IO N

An extended sound is achieved for a 2 channel source such as a CD player.

Press STEREO to enter extended stereo mode. EXTENDED appears in the front panel display.

Each time you press STEREO, the function is turned on (EXTENDED) and off (STEREO) alternately.

y The default setting is STEREO. The system memorizes the settings assigned to each input

source. You can also turn on compressed music enhancer mode when

extended stereo mode is turned on.

This operation is only available when surround mode is not activated.

This function enhances your listening experience by regenerating the missing harmonics in a compression artifact. This is useful when you play back compressed music data stored on an iPod or a digital music player.

Press ENHANCER. The ENHANCER indicator lights up in the front panel display when this function is turned on. Each time you press ENHANCER, the function is turned on and off alternately. The selected mode is stored in memory even when the power is off.

y The default setting is OFF. The system memorizes the settings assigned to each input

source. When this function is on, night listening mode is automatically

set to off. ( P. 32)

Using extended stereo mode

STEREO

Note

Setting compressed music enhancer

ENHANCER

21 En

OTHER FUNCTIONS

You can use two tuning modes to tune into the desired FM station:

Frequency tuning mode You can search or specify the frequency of the desired FM station automatically or manually. (See Basic tuning operation on page 23.)

Preset tuning mode You can preset the desired FM station in advance, and then recall the station by specifying the preset group and number. (See Using station preset feature on page 24.)

LISTENING TO FM BROADCASTS

Overview

Controls and functions for the FM tuning

A E/A E

Selects the preset group (A to E).

PRESET/TUNE

Switches between frequency tuning mode and preset tuning mode.

AUTO/MANL

Switches between automatic and manual tuning mode.

FM

Sets the input to FM.

+/

Selects the desired frequency in frequency tuning mode.

Selects the desired preset number (1 to 8) in preset tuning mode.

MEMORY

Activates the preset memory mode.

22 En

LISTENING TO FM BROADCASTS E

n g

lish O

T H

E R

F

U N

C T

IO N

S

1 Press FM to set the input to FM. FM appears in the front panel display.

2 Press AUTO/MANL to switch Auto/Manual. The AUTO indicator lights up when the system is set to automatic tuning mode.

y If a colon (:) appears, the system is set to preset tuning mode. ( P. 24)

3 Press +/ once to begin automatic tuning. When the system is tuned to a station, the TUNED indicator lights up and the frequency of the received station is shown in the front panel display.

y When you tune to an FM station using automatic tuning mode, the system receives the FM radio signal in stereo reception mode. The STEREO indicator appears in the front panel display.

Basic tuning operation

No colon (:)

Lights up

Lights up

Manual tuning If the signal received from the station you want to select is weak, you can tune into the desired station by specifying the frequency manually. In FM tuning mode, press AUTO/MANL repeatedly so that the AUTO indicator disappears, and then press +/ repeatedly to specify the frequency of the desired station. If you tune to a station using the manual tuning feature, the system receives the FM radio signals in monaural reception mode to increase signal quality.

23 En

LISTENING TO FM BROADCASTS

Automatic station preset You can store up to 40 FM stations (A1 to E8: 8 preset numbers in each of the 5 preset groups).

y Press A E or A E to select a preset group, and then press +/ repeatedly to select a preset number to which the first station will be stored after you perform step 2.

Any stored station data existing under a preset number is cleared when you store a new station under the same preset number. If the number of received stations does not reach 40 (A1 to E8), automatic preset tuning automatically stops after searching for all the

available stations.

Using station preset feature

1 Press FM to set the input to FM. FM appears in the front panel display.

2 Press and hold MEMORY for more than 3 seconds. The preset group and number as well as the MEMORY and AUTO indicators flash. After approximately 5 seconds, automatic presetting starts from the current frequency and proceeds through higher frequencies.

Press MEMORY again to cancel while the MEMORY indicator is flashing.

When automatic preset tuning is completed, the front panel display shows the frequency of the last preset station.

Flash

Flashes

Notes

If the desired station is not stored, or a station is not stored to the desired preset group and number, preset the station manually. Refer to Manual station preset on page 25 for details.

24 En

LISTENING TO FM BROADCASTS E

n g

lish O

T H

E R

F

U N

C T

IO N

S

Manual station preset Use this feature to preset your desired station manually.

1 Tune into a station. See Basic tuning operation on page 23 for tuning instructions.

2 Press MEMORY. The MEMORY indicator flashes in the front panel display for approximately 30 seconds.

Press MEMORY again to cancel while the MEMORY indicator is flashing.

3 Press A E or A E repeatedly to select a preset group (A to E) while the MEMORY indicator is flashing. The selected preset group appears.

4 Press +/ to select a preset number (1 to 8) while the MEMORY indicator is flashing.

5 Press MEMORY to confirm the preset.

After A1:PRESET OK appears in the front panel display, the frequency appears with the preset group you selected. The MEMORY indicator disappears from the front panel display.

Any stored station data existing under a preset number is cleared when you store a new station under the same preset number.

Reception mode (stereo or monaural) is stored along with the station frequency.

Flashes

Preset group

Flashes

Notes

Flashes

Preset number

The selected station has been stored as A1.

25 En

LISTENING TO FM BROADCASTS

Recalling the preset stations

1 Press PRESET/TUNE to select preset tuning mode.

2 Press A E or A E repeatedly to select the desired preset group (A to E).

3 Press +/ repeatedly to select the desired preset number (1 to 8).

Preset group and number

Preset FM station

26 En

E n

g lish

O T

H E

R

F U

N C

T IO

N S

Once you have stationed your iPod in the Yamaha iPod universal dock (such as YDS-10/ YDS-11, sold separately) connected to the DOCK terminal of the subwoofer/system control ( P. 14), you can enjoy playback of your iPod.

Supported iPod iPod (Click and Wheel) iPod nano iPod mini

Battery charge feature This system charges the battery of an iPod stationed in the Yamaha iPod universal dock connected to the DOCK terminal of the subwoofer/system control while this system is turned on.

Stationing your iPod in the Yamaha iPod universal dock Once you station your iPod in the Yamaha iPod universal dock, iPod connected and the DOCK indicator appear in the front panel display.

Some features may not be available depending on the model or the software version of your iPod. For a complete list of status messages that appear in the front panel display, see the iPod section in Troubleshooting on page 35. Be sure to set the volume to minimum before docking or removing your iPod.

Controls and functions for iPod You can control your iPod in simple remote mode or menu browse mode.

y You can switch between simple remote mode and menu browse mode by pressing DOCK MODE.

USING OPTIONAL EQUIPMENT

Using iPod

Notes

DOCK MODE

Switch simple remote mode and menu browse mode.

Playback control buttons

Control the playback of the connected iPod. p: Play/pause (Simple remote mode), Play (Menu browse mode) e: Play/pause (Simple remote mode), Pause (Menu browse mode) s: Stop b/a: Skip backward/forward Search backward/forward (Press and hold)

DOCK

Set the input to DOCK.

MENU/Cursor buttons ( / / / )/ENTER

Navigate the menu of your iPod. Press to move to an upper

menu level. Press / to move the cursor to

select a menu. Press ENTER or to enter the

selected menu. Press ENTER in the Songs

level menu screen to play back the selected song.

27 En

USING OPTIONAL EQUIPMENT

Controlling your iPod in simple remote mode Docking your iPod in the Yamaha iPod universal dock (such as YDS-10 or YDS-11, sold separately) enters simple remote mode. You can perform the basic operations of your iPod (play, stop, skip backward/forward, etc.) using the supplied remote control in this mode.

y Operations can be also done with the controls on your iPod. Refer to the instruction manuals of your iPod for its operations.

Controlling your iPod in menu browse mode The song lists or playback information is displayed in the front panel display so that you can select and play back songs or adjust settings using the supplied remote control in this mode.

Operations cannot be done with the controls of your iPod. Characters that cannot be displayed in the front panel display are replaced with underscores _.

1 Press DOCK MODE to enter menu browse mode.

2 Press / / / repeatedly to select the desired menu, and then press ENTER to play back the selected song.

The setting list has the following 2 choices.

Shuffle Use this feature to set the system to play songs or albums in random order.

Options: Off, Songs, Album You can switch each option by pressing ENTER. Select Off to deactivate this feature. Select Songs to set the system to play songs in random order. Select Album to set the system to play albums in random order.

Repeat Use this feature to set the system to repeat one song or a sequence of songs.

Options: Off, One, All You can switch each option by pressing ENTER. Select Off to deactivate this feature. Select One to set the system to repeat one song. Select All to set the system to repeat a sequence of songs.

The contents of the iPod menu vary, depending on the model or the generation.

Notes

Options Level 1 Level 2 Level 3 Level 4

Playlists Playlist Song list

Artists Artist list Album list Song list

Albums Album list Song list

Songs Song list

Genres Genre list Artist list Album list Song list

Composers Composer list Album list Song list

Settings Setting list

Note

28 En

USING OPTIONAL EQUIPMENT E

n g

lish O

T H

E R

F

U N

C T

IO N

S

You can connect the Yamaha Bluetooth audio receiver (such as YBA-10, sold separately) to the DOCK terminal of the subwoofer/system control and enjoy the music contents stored in your Bluetooth component (such as a portable music player or computer equipped with a Bluetooth transmitter, etc.) without wiring between the system and the Bluetooth component. You need to perform pairing of the connected Yamaha Bluetooth audio receiver and your Bluetooth component in advance.

Controls and functions for Bluetooth components

Pairing the Yamaha Bluetooth audio receiver and your Bluetooth component

Pairing must be performed before using a Bluetooth component with the Yamaha Bluetooth audio receiver connected to the system for the first time or if the registered pairing data has been deleted. Pairing refers to the operation of registering a Bluetooth component for Bluetooth communications.

1 Connect the Yamaha Bluetooth audio receiver to the DOCK terminal of the subwoofer/system control. ( P. 14)

2 Press DOCK to set the input to DOCK.

3 Turn on the Bluetooth component you want to pair with, and then enter pairing mode. Refer to the instruction manual of your Bluetooth component for details.

Using Bluetooth components

To ensure security, a time limit of 8 minutes is set for the pairing operation. Please read and fully understand all the instructions before starting.

BLUETOOTH ON/OFF

Start or cancel the pairing. Connect or disconnect a

Bluetooth component.

DOCK

Set the input to DOCK.

Playback control buttons

Control the playback of a Bluetooth component. p: Play e: Pause s: Stop b/a: Skip backward/forward

29 En

USING OPTIONAL EQUIPMENT

4 Press and hold BLUETOOTH ON for more than 3 seconds to start pairing. Searching... appears when the pairing starts. While the Yamaha Bluetooth audio receiver is in pairing mode, the DOCK indicator flashes in the front panel display.

y To cancel the pairing, press BLUETOOTH OFF.

5 Check that the Bluetooth component detects the Yamaha Bluetooth audio receiver. If the Bluetooth component detects the Yamaha Bluetooth audio receiver, the audio receiver name (YBA-10 YAMAHA for example) appears in the device list of the Bluetooth component.

6 Select the Yamaha Bluetooth audio receiver in the device list of the Bluetooth component, and then enter the pass key 0000 on the Bluetooth component. When the pairing procedure is successful, Completed appears in the front panel display.

y If the pairing is not completed within 8 minutes, Not found appears and the DOCK indicator is turned off in the front panel

display. If the pairing is canceled during the pairing, Canceled appears in the front panel display.

The Yamaha Bluetooth audio receiver can be paired with up to eight Bluetooth components. When pairing is conducted successfully with a ninth component and the pairing data is registered, the pairing data for the least recently used another component is deleted.

Establishing a connection After the pairing is completed, perform the connecting operation on the system or on the Bluetooth component to enable communication between them. The connecting operation on the system is only available for the most recently connected Bluetooth component.

1 Press DOCK to set the input to DOCK.

2 Press BLUETOOTH ON to start a connection. Searching... appears in the front panel display. When the system finds the last connected Bluetooth component, BT connected appears in the front panel display for 3 seconds.

y If the system cannot find the last connected Bluetooth component, Not found appears in the front panel display. If you want to establish a connection with a Bluetooth component other than the one most recently connected to, connect from

that Bluetooth component. Refer to the instruction manual of your Bluetooth component for details.

Disconnecting

Press DOCK, and then BLUETOOTH OFF to disconnect the system from the Bluetooth component. Disconnected appears in the front panel display.

Playing back the Bluetooth component You can play back your Bluetooth component using the supplied remote control. You can also play back your Bluetooth component by operating it directly.

y Operation using the remote control is available only when the connection is established between the Bluetooth component you want to play back and the system.

Note

30 En

USEFUL OPERATION

E

n g

lish U

S E

F U

L

O P

E R

A T

IO N

FPD TV images sometimes lag behind the sound. You can use this function to delay the sound output to synchronize it with the video image.

ADJUSTING THE AUDIO DELAY

1 Press AUDIO DELAY to enter adjusting mode.

2 Press / to adjust the delay time. Options: 0 to 240 ms You can adjust the delay time by the 10 ms.

3 Press AUDIO DELAY again or ENTER to exit adjusting mode.

y The default setting is 0 ms and DELAY OFF appears in the

front panel display. The system memorizes the settings assigned to each input

source.

If you do not operate this function within 30 seconds after entering adjusting mode, the system automatically exits adjusting mode.

Note

Setting value

31 En

Night listening mode enables you to listen to dialog or vocals more clearly at lower volume by suppressing louder sound effects. This function is useful when you enjoy movies or music at night.

Press NIGHT. NIGHT ON appears in the front panel display. The NIGHT indicator lights up when Night listening mode is selected.

y To cancel night listening mode, press NIGHT again. When this function is on, compressed music enhancer mode is

automatically set to off. ( P. 21) The setting is set for all the input sources.

You can adjust the volume balance of the virtual speakers and subwoofer.

y You can also adjust the speaker volume while the test tone is output. ( P. 20) The setting is set for all the input sources.

LISTENING AT LOW VOLUME (NIGHT LISTENING MODE)

NIGHT Lights up

ADJUSTING THE VOLUME BALANCE DURING PLAYBACK

SW +/

Adjusts the output level of the subwoofer channel. Control range: +6 to 6

CENTER +/

Adjusts the output level of the center virtual speaker channel. Control range: +6 to 6

SUR. +/

Adjusts the output level of the surround/ surround back virtual speaker channels. Control range: +6 to 6

32 En

E n

g lish

U S

E F

U L

O

P E

R A

T IO

N

You can change the brightness of the front panel display. You can also turn off the front panel display to view a movie in a darker environment.

CHANGING THE BRIGHTNESS OF THE FRONT PANEL DISPLAY

Press DISP. MODE repeatedly. Each time you press DISP. MODE, the brightness of the front panel changes.

* Selecting DISPLAY OFF turns off the front panel display after DISPLAY OFF appears in the front panel display.

The front panel display lights up momentarily when any operation is performed with DISPLAY OFF mode selected. Only the power indicator remains lit in DISPLAY OFF mode.

y The default setting is DIMMER OFF.

Bright

Dark

DISP. MODE

33 En

ADDITIONAL INFORMATION

If there is any problem with the system, check the following items. If you cannot solve a problem with the following remedies, or if the problem is not listed below, turn off and unplug the system, and then consult your nearest authorized Yamaha dealer or Service Center.

ADDITIONAL INFORMATION

Troubleshooting

Problem Cause Solution See

page

Power turns on but immediately shuts off.

The power cable may be connected improperly.

Make sure the power cable is plugged into the outlet firmly.

15

A speaker cable may be shorted. Make sure all speaker cables are connected properly.

11

This system may have received a strong electrical shock, such as from a lightening bolt or excessive static electricity.

Set this system to standby mode, and then disconnect the power cable. Wait for about 30 seconds, connect the power cable, and then turn the system on again.

16

The speakers make no sound.

The volume may be set to minimum level.

Adjust the volume level. 16, 32

The mute function may be activated. Cancel the mute function. 16

The input source or input setting may be incorrect.

Select the correct input source or input setting. 16

The cables may be connected improperly.

Make sure all cables are connected properly. 11

Sound is too low on one side.

The cables may be connected improperly.

Make sure all cables are connected properly. 11

Speaker channels other than the front ones make no sound.

You may be listening to stereo sounds without surround mode.

Press a surround mode button to enable the sound field effect. 18

The center speaker channel makes no sound.

The volume of the center virtual speaker channel may be set to minimum level.

Adjust the volume level of the center virtual speaker channel. 32

The surround speaker channels make no sound.

The volume of the surround virtual speaker channels may be set to minimum level.

Adjust the volume level of the surround virtual speaker channels. 32

The subwoofer makes no sound.

The volume of the subwoofer channel may be set to minimum level.

Adjust the volume level of the subwoofer. 32

Sound is poor (noisy). A speaker cable may be shorted. Make sure all cables are connected properly. 11

This system does not operate properly.

This system may receive a strong electrical shock, such as from a lightening bolt or excessive static electricity, or drop in power supply.

Set this system to standby mode, and then disconnect the power cable. Wait for about 30 seconds, connect the power cable, and then turn on this system.

16

The system control cable may be connected improperly.

Connect the system cable firmly. 11

A digital or high- frequency equipment produces noises.

The system may be placed close to digital equipment or high-frequency equipment.

Place this system farther away from such equipment.

34 En

ADDITIONAL INFORMATION E

n g

lish A

D D

IT IO

N A

L

IN F

O R

M A

T IO

N

Tuner

iPod

In case of a transmission error without a status message appearing in the front panel, check the connection to your iPod ( P. 14).

The remote control does not operate the system.

The system may be outside the remote control operation range.

For information on the remote control operation range, refer to Using the remote control.

7

The remote control sensor of this system may be exposed to direct sunlight or lighting.

Change the lighting.

The batteries may be worn out. Replace the batteries. 7

Problem Cause Remedy See

page

FM stereo reception is noisy.

The characteristics of FM stereo broadcasts may cause this problem when the transmitter is too far away, or if the antenna quality is poor.

Check the antenna connections. 14

Try using a high-quality directional FM antenna.

Use the manual tuning method. 23

There is distortion, and clear reception cannot be obtained, even with a good FM antenna.

There is multi-path interference. Adjust the antenna position to eliminate multi- path interference.

The desired station cannot be tuned into with the automatic tuning method.

The signal is too weak. Use a high-quality directional FM antenna.

Use the manual tuning method. 23

Note

Status message Cause Remedy See

page

Unknown iPod The iPod being used is not supported by this system.

Only iPod (Click and Wheel), iPod nano, and iPod mini are supported.

iPod connected Your iPod is properly stationed in the Yamaha iPod universal dock (such as YDS-10 or YDS-11, sold separately) connected to the DOCK terminal of this system, and the connection between your iPod and this system is completed.

Disconnected Your iPod was removed from the Yamaha iPod universal dock (such as YDS-10 or YDS-11, sold separately) connected to the DOCK terminal of this system.

Station your iPod back in the Yamaha iPod universal dock (YDS-10 or YDS-11, sold separately) connected to the DOCK terminal of this system.

14, 27

Problem Cause Solution See

page

35 En

ADDITIONAL INFORMATION

Bluetooth

In case of a transmission error without a status message appearing in the front panel, check your Bluetooth component.

Note

Status message Cause Remedy See

page

Searching... The Yamaha Bluetooth audio receiver (such as YBA-10, sold separately) and the Bluetooth component are in the process of the pairing.

The Yamaha Bluetooth audio receiver (such as YBA-10, sold separately) and the Bluetooth component are in the process of establishing the connection.

Completed The pairing is completed.

Canceled The pairing is canceled.

Not found The system cannot find the Bluetooth component while performing the pairing or trying to connect to the Bluetooth component.

BT connected The connection between the Yamaha Bluetooth audio receiver (such as YBA- 10, sold separately) and the Bluetooth component is established.

Disconnected The Bluetooth component is disconnected from the Yamaha Bluetooth audio receiver (such as YBA-10, sold separately).

Not Available The pairing is performed when the Yamaha Bluetooth audio receiver (such as YBA-10, sold separately) is connected to the Bluetooth component.

Perform the pairing when the Yamaha Bluetooth audio receiver (such as YBA-10, sold separately) is not connected to the Bluetooth component.

29

36 En

ADDITIONAL INFORMATION E

n g

lish A

D D

IT IO

N A

L

IN F

O R

M A

T IO

N

AIR SURROUND XTREME New surround technology developed by Yamaha enables surround sound with fewer speakers. In comparison to traditional front surround technology, the AIR SURROUND XTREME provides a natural surround sound field.

Channel (ch) A channel is an audio type that has been divided based on range and other characteristics. Ex. 7.1 channel Front speakers, Left (1ch), Right (1ch) Center speaker (1ch) Surround speakers, Left (1ch), Right (1ch) Surround back speakers, Left (1ch), Right (1ch) Subwoofer (1ch 0.1* = 0.1ch) * In contrast to a full 1-channel band, a component designed to

enhance low frequency sound for added effect.

Dolby Digital Digital surround sound system which is developed by Dolby Laboratories provides completely independent multi-channel audio. With 3 front channels (left, center, and right) and 2 surround stereo channels, Dolby Digital provides five full-range audio channels. With an additional channel especially for bass effects (called LFE, or low frequency effect), the system has a total of 5.1- channels (LFE is counted as 0.1 channel). By using 2- channel stereo for the surround speakers, more accurate moving sound effects and surround sound environment are possible than with Dolby Surround.

Dolby Pro Logic II It is an improved matrix decoding technology that provides better spatiality and directionality on Dolby Surround programmed material; provides a convincing three-dimensional sound field on conventional stereo music recordings; and is ideally suited to bring the surround experience to automotive sound. While conventional surround programming is fully compatible with Dolby Surround Pro Logic II decoders, soundtracks will be able to be encoded specifically to take full advantage of Pro Logic II playback, including separate left and right surround channels.

DTS Digital surround sound system developed by DTS, Inc., which provides 5.1 channel audio. With an abundance of audio data, it is able to provide authentic-sounding effects.

PCM (Pulse Code Modulation) A signal that is changed to digital format without compression. A CD is recorded with 16-bit sound at 44.1 kHz, while DVD recording is anywhere from 16 bits at 48 kHz to 24 bits at 192 kHz, which makes it a higher quality sound than CD.

Sampling frequency The number of sampling (process for digitalizing analog signals) per second. In principle, the higher the sampling rate, the wider the frequency range that can be played back, and the higher the quantized bit rate, the finer the sound that can be reproduced.

Glossary

37 En

ADDITIONAL INFORMATION

YAS-71CU Type...................2 way acoustic suspension magnetic shielding type Driver

Woofer............ 8 cm (3) cone magnetic shielding type 4 (L2, R2) Tweeter.............2.5 cm (1) balanced dome magnetic shielding type

2 (L1, R1) Frequency Response................................ 120 Hz to 20 kHz (-10 dB) Dimensions (W H D) ..................................800 105 100 mm

(Approx. 31-1/2 4-1/8 3-15/16) Weight ....................................................................................... 5 kg

(Approx. 11 lbs.)

YAS-71SPX Amplifier Minimum RMS output power per channel

L/R............................................ 55 W + 55 W (1 kHz 1% THD + N) Subwoofer ........................................... 55 W (100 Hz 1% THD + N)

Maximum power per channel L/R.......................................... 70 W + 70 W (1 kHz 10% THD + N) Subwoofer ......................................... 70 W (100 Hz 10% THD + N)

FM Tuner Tuning range

[U.S.A. and Canada models] ........................... 87.50 to 107.90 MHz [Other models]................................................. 87.50 to 108.00 MHz

Antenna Input (unbalanced) ..................................................... 75

Subwoofer Type ..........................................................................Bass reflex type Driver.........................16 cm (6-1/2) cone, Magnetic shielding type Frequency Response ..................................35 Hz to 120 Hz (-10 dB)

Other sections Power supply

[Taiwan model].......................................................AC 110 V, 60 Hz [U.S.A. and Canada models] ..................................AC 120 V, 60 Hz [China model] .........................................................AC 220 V, 50 Hz [Korea model].........................................................AC 220 V, 60 Hz [Asia and Europe models] ......................................AC 230 V, 50 Hz [Australia model] ....................................................AC 240 V, 50 Hz

Power consumption .................................................................. 50 W Standby Power Consumption ...........................................1 W or less Dimensions (W H D) ................................. 194 450 400 mm

(Approx. 7-5/8 17-3/4 15-3/4) Weight .......................................................................................13 kg

(Approx. 28 lbs. 11 oz)

* Specifications are subject to change without notice.

This system employs new technologies and algorithms that make it possible to achieve 7-channel surround sound with only two front speakers, and without using wall reflections.

Manufactured under license from Dolby Laboratories. Dolby, Pro Logic and the double-D symbol are trademarks of Dolby Laboratories.

DTS and DTS Digital Surround are registered trademarks of DTS, Inc.

Specifications

38 En

Manualsnet FAQs

If you want to find out how the YAS-71SPX Yamaha works, you can view and download the Yamaha YAS-71SPX Remote Control Owner's Manual on the Manualsnet website.

Yes, we have the Owner's Manual for Yamaha YAS-71SPX as well as other Yamaha manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Owner's Manual should include all the details that are needed to use a Yamaha YAS-71SPX. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Yamaha YAS-71SPX Remote Control Owner's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Yamaha YAS-71SPX Remote Control Owner's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Yamaha YAS-71SPX Remote Control Owner's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Yamaha YAS-71SPX Remote Control Owner's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Yamaha YAS-71SPX Remote Control Owner's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.