Contents

Yamaha CRX-330 Receiver Owner's Manual PDF

1 of 32
1 of 32

Summary of Content for Yamaha CRX-330 Receiver Owner's Manual PDF

OWNER'S MANUAL MODE D'EMPLOI

UA

AMPLI-TUNER CD CD RECEIVER

i En

Explanation of Graphical Symbols The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

1 Read these instructions.

2 Keep these instructions. 3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water. 6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in accordance with the manufacturers instructions.

8 Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9 Do not defeat the safety purpose of the polarized or grounding- type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10 Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11 Only use attachments/accessories specified by the manufacturer. 12 Use only with the cart, stand, tripod, bracket, or

table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13 Unplug this apparatus during lightning storms or when unused for long periods of time.

14 Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

IMPORTANT SAFETY INSTRUCTIONS

Note to CATV system installer: This reminder is provided to call the CATV system installers attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

IMPORTANT Please record the serial number of this unit in the space below. MODEL: Serial No.: The serial number is located on the rear of the unit. Retain this Owners Manual in a safe place for future reference.

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

We Want You Listening For A Lifetime Yamaha and the Electronic Industries Associations Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or distortion and, most importantly, without affecting your sensitive hearing. Since hearing damage from loud sounds is often undetectable until it is too late, Yamaha and the Electronic Industries Associations Consumer Electronics Group recommend you to avoid prolonged exposure from excessive volume levels.

ii En

FCC INFORMATION (for US customers)

1 IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.

2 IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA.

3 NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class B digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices.

Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit OFF and ON, please try to eliminate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by the interference.

Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s. In the case of radio or TV interference, relocate/ reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA 90620.

The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.

CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

The label is located on the bottom of the unit. (U.S.A and Canada models only)

DANGER:

CAUTION:

AVOID DIRECT EXPOSURE TO THE BEAM INVISIBLE LASER RADIATION WHEN OPEN

DO NOT STARE INTO BEAM INVISIBLE LASER RADIATION WHEN OPEN

iii En

1 To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference.

2 Install this unit in a well ventilated, cool, dry, clean place with at least 10 cm on the top, 10 cm on the left and right, and 10 cm at the back of this unit away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold.

3 Locate this unit away from other electrical appliances, motors, or transformers to avoid humming sounds.

4 Do not expose this unit to sudden temperature changes from cold to hot, and do not locate this unit in an environment with high humidity (i.e. a room with a humidifier) to prevent condensation inside this unit, which may cause an electrical shock, fire, damage to this unit, and/or personal injury.

5 Avoid installing this unit where foreign object may fall onto this unit and/or this unit may be exposed to liquid dripping or splashing. On the top of this unit, do not place: Other components, as they may cause damage and/or

discoloration on the surface of this unit. Burning objects (i.e. candles), as they may cause fire, damage

to this unit, and/or personal injury. Containers with liquid in them, as they may fall and liquid

may cause electrical shock to the user and/or damage to this unit.

6 Do not cover this unit with a newspaper, tablecloth, curtain, etc. in order not to obstruct heat radiation. If the temperature inside this unit rises, it may cause fire, damage to this unit, and/or personal injury.

7 Do not plug in this unit to a wall outlet until all connections are complete.

8 Do not operate this unit upside-down. It may overheat, possibly causing damage.

9 Do not use force on switches, knobs and/or cords.

10 When disconnecting the power cable from the wall outlet, grasp the plug; do not pull the cable.

11 Do not clean this unit with chemical solvents; this might damage the finish. Use a clean, dry cloth.

12 Only voltage specified on this unit must be used. Using this unit with a higher voltage than specified is dangerous and may cause fire, damage to this unit, and/or personal injury. Yamaha will not be held responsible for any damage resulting from use of this unit with a voltage other than specified.

13 To prevent damage by lightning, keep the power cord and outdoor antennas disconnected from a wall outlet or this unit during a lightning storm.

14 Do not attempt to modify or fix this unit. Contact qualified Yamaha service personnel when any service is needed. The cabinet should never be opened for any reasons.

15 When not planning to use this unit for long periods of time (i.e. vacation), disconnect the AC power plug from the wall outlet.

16 Be sure to read the TROUBLESHOOTING section on common operating errors before concluding that this unit is faulty.

17 Before moving this unit, press STANDBY/ON to set this unit to the standby mode, and disconnect the AC power plug from the wall outlet.

18 Condensation will form when the surrounding temperature changes suddenly. Disconnect the power cable from the outlet, then leave this unit alone.

19 When using this unit for a long time, this unit may become warm. Turn the power off, then leave this unit alone for cooling.

20 Install this unit near the AC outlet and where the AC power plug can be reached easily.

21 The batteries shall not be exposed to excessive heat such as sunshine, fire or the like.

22 Excessive sound pressure from earphones and headphones can cause hearing loss.

LASER SAFETY This unit employs a laser. Due to possible eye injury, only a qualified service person should remove the cover or attempt to service this device.

DANGER This unit emits visible laser radiation when open. Avoid direct eye exposure to beam. When this unit is plugged into the wall outlet, do not place your eyes close to the opening of the disc tray and other openings to look into inside.

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.

This unit is not disconnected from the AC power source as long as it is connected to the wall outlet, even if this unit itself is turned off by STANDBY/ON. This state is called the standby mode. In this state, this unit is designed to consume a very small quantity of power.

The laser component in this product is capable of emitting radiation exceeding the limit for Class 1.

WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

FOR CANADIAN CUSTOMERS To prevent electric shock, match wide blade of plug to wide slot and fully insert. This Class B digital apparatus complies with Canadian ICES-003.

CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

1 En

E n

g lish

P R

E P

A R

A T

IO N

IN T

R O

D U

C T

IO N

T U

N E

R

O P

E R

A T

IO N

S O

T H

E R

O

P E

R A

T IO

N S

A D

D IT

IO N

A L

IN

F O

R M

A T

IO N

B A

S IC

O

P E

R A

T IO

N S

FEATURES............................................................. 2 SUPPLIED ACCESSORIES ................................. 2 CONTROLS AND FUNCTIONS ......................... 3

Front panel ................................................................. 3 Front panel display .................................................... 4 Remote control........................................................... 5

CONNECTING SPEAKERS ................................ 9 Connecting a subwoofer .......................................... 10

CONNECTING ANTENNAS.............................. 11 Connecting the FM antenna..................................... 11

CONNECTING THE POWER CABLES .......... 11 CONNECTING HEADPHONES........................ 11 CONNECTING EXTERNAL COMPONENTS ...12

Connecting a USB device........................................ 12 Connecting an iPod.............................................. 12

BASIC RECEIVER OPERATIONS .................. 13 SETTING THE SLEEP TIMER......................... 14 BASIC PLAYBACK OPERATIONS FOR DISCS

AND USB DEVICES........................................ 15 Switching the playback information display ........... 16 Repeating playback (Repeat Play)........................... 17 Playing back randomly (Shuffle Play)..................... 17

FM TUNING......................................................... 18 Automatic tuning ..................................................... 18 Manual tuning.......................................................... 18 Automatic preset tuning........................................... 18 Manual preset tuning ............................................... 19 Selecting preset stations........................................... 19

CONTROLLING iPod......................................20 Using iPod ........................................................... 20

TROUBLESHOOTING .......................................22 General..................................................................... 22 Radio reception........................................................ 22 iPod ...................................................................... 23 USB ......................................................................... 23 Disc Playback .......................................................... 24 Remote control ........................................................ 24

NOTES ABOUT DISCS/MP3, WMA FILES.....25 GLOSSARY...........................................................27

Audio information ................................................... 27 Copyright and logo marks ....................................... 27

SPECIFICATIONS...............................................27

CONTENTS

INTRODUCTION

PREPARATION

BASIC OPERATIONS

TUNER OPERATIONS

OTHER OPERATIONS

ADDITIONAL INFORMATION

FEATURES

2 En

Maximum RMS output power per channel 20W + 20W (10% THD, 1 kHz, 6)

30-station FM preset tuning iPod playability

Plays Audio CDs, MP3/WMA discs CD Text data display MP3/WMA file playability stored on USB

device Multi function remote control

About this manual This manual describes how to operate this unit using a remote control except when it is not available. Some of these operations are

also available using the front panel buttons. The round shaped button on the center of the remote control is called Center in this manual. y indicates a tip for your operation. Notes contain important information about safety and operating instructions. This manual is printed prior to production. Design and specifications are subject to change in part as a result of improvements, etc. In

case of differences between the manual and the product, the product has priority.

This product includes the following accessories. Before connecting speakers, make sure you received all of the following parts.

FEATURES

SUPPLIED ACCESSORIES

STANDBY ON

CD iPod FM USB

SLEEP

FMPRESET

FUNCTION

MENU

DISPLAY

FOLDER

SHUFFLE REPEAT

MUTE VOLUME

TUNING MEMORY

USB

iPod

Indoor FM antennaRemote control

USB cap* Dock cover*

*The USB cap and the Dock cover are supplied with this unit to cover the USB port and the iPod terminal when not using.

When the USB cap and the Dock cover are covered.

(Other models)

(U.S.A and Canada models)

3 En

E n

g lish

IN T

R O

D U

C T

IO N

1 STANDBY/ON Turns this unit on or sets it to the standby mode.

2 Disc Tray Loads a disc to be played back.

3 Front panel display Shows the various information such as the tuning frequency.

4

Opens and closes the disc tray.

5 PHONES Outputs audio signals for private listening with headphones.

6 Remote control sensor Receives signals from the remote control.

7 VOLUME Adjusts the volume level.

8 INPUT Selects an input source.

9

Stops playback (see page 15).

0

Starts or pauses playback (see page 15).

A USB port Connect your USB device (see page 12).

B iPod terminal Connect your iPod (see page 12).

CONTROLS AND FUNCTIONS

Front panel

USB

IPod

A B

Top view

STANDBY ON PHONES

VOLUME

INPUT

5

1 2 3 4

6 7 8 9 0

Front view

4 En

CONTROLS AND FUNCTIONS

1 SLEEP indicator Lights up when the sleep timer is on (see page 14).

2 PRESET indicator Lights up when you preset radio stations (see page 19).

3 STEREO indicator Lights up when this unit is receiving a strong signal from an FM stereo broadcast.

4 AUTO indicator Lights up when this unit is in the Automatic Tuning mode (see page 18).

5 SHUFFLE indicator Lights up when you set your iPod/CD/USB in shuffle mode.

6 REPEAT indicator Lights up when you set your iPod/CD/USB in repeat mode.

7 MUTE indicator Lights up when the sound is muted.

8 Multi information display Shows the various information such as the tuning frequency.

9 TUNED indicator Lights up when this unit is tuned into a station.

0 MEMORY indicator Lights up when you preset radio stations automatically or manually.

A Multi information indicator Light up the menu currently selected (see page 20).

B Operation indicators Show operable cursor keys when operating with the FUNCTION or iPod menu with the menu browse mode (see page 20).

Front panel display

GENRESSONGSALBUMSARTISTSPLAYLISTSMEMORYTUNED SLEEP STEREO AUTO SHUFFLE REPEAT MUTEPRESET

1 2 3 4 75 6

9 A

B

8 0

5 En

CONTROLS AND FUNCTIONS E

n g

lish IN

T R

O D

U C

T IO

N

This remote control can operate the system components and an iPod stationed in a terminal on the top panel of this unit. To operate the CD, USB device, tuner functions, or an iPod using the remote control, you need to set this unit to the corresponding input mode.

To switch the input mode of this unit Press the corresponding input selection key on the remote control (or INPUT on the front panel). The input mode automatically changes to iPod when you connect the iPod during the playback (see page 12). The name of the corresponding input source appears in the front panel display of this unit.

Common functions Operations common to all modes The following operations are available for this unit when it is set to any input mode.

1 Infrared signal transmitter Sends signals to the component you want to control.

2 STANDBY/ON Turns this unit on or sets it to the standby mode.

3 Input selection keys Select the input source.

4 FUNCTION By pressing FUNCTION, you can select DIMMER, TREBLE, BASS, BALANCE, or ECO MODE.

5 DISPLAY Switches the information shown in the front panel display (see page 16).

6 MUTE Turn off the sound. To restore the sound, press MUTE again or press VOLUME (down)/ (up).

7 SLEEP Sets the sleep timer (see page 14).

8 VOLUME (down) / (up) Adjusts the overall volume level.

Remote control

STANDBY ON

CD iPod FM USB

SLEEP

FMPRESET

FUNCTION

MENU

TUNING MEMORY

Input selection keys

STANDBY ON

CD iPod FM USB

SLEEP

FMPRESET

FUNCTION

MENU

DISPLAY

FOLDER

SHUFFLE REPEAT

MUTE VOLUME

TUNING MEMORY

3

2

1

4

7

6 8

5

6 En

CONTROLS AND FUNCTIONS

CD/USB mode Operations available in CD/USB mode The following operations are available for this unit when the CD or USB mode is selected.

1 , Skips to the beginning of the current track or next track. Press and hold to fast reverse or fast forward (see page 15). Press twice to skip to the beginning of the previous track.

2 DISPLAY Switches the disc/USB information shown in the front panel display (see page 16).

3 FOLDER / Press FOLDER / to playback a first file of selected folder for an MP3 or a WMA folder recorded on disc/USB device (see page 15). *During Shuffle Play, these buttons cannot be used.

4

Starts or pauses playback (see page 15).

5

Stops playback (see page 15).

6 REPEAT Selects the Repeat Play mode (see page 17).

7 SHUFFLE Select the Shuffle Play feature (see page 17).

FM mode Operations available in FM mode The following operations are available for this unit when the FM mode is selected.

1 TUNING / Press TUNING / to Manual tuning and press and hold TUNING / to Automatic tuning.

2 PRESET / Press PRESET / to select a preset station (see page 18).

3 MEMORY Starts preset memory mode.

4 Center Press Center to fix the current setting.

STANDBY ON

CD iPod FM USB

SLEEP

FMPRESET

FUNCTION

MENU

DISPLAY

FOLDER

SHUFFLE REPEAT

MUTE VOLUME

TUNING MEMORY

3 2

1

7

5

6

4

STANDBY ON

CD iPod FM USB

SLEEP

FMPRESET

FUNCTION

MENU

DISPLAY

FOLDER

SHUFFLE REPEAT

MUTE VOLUME

TUNING MEMORY

4

2

1 3

7 En

CONTROLS AND FUNCTIONS E

n g

lish IN

T R

O D

U C

T IO

N

iPod mode Operations available in iPod mode The following operations are available for the iPod stationed in the terminal. For details on iPod operations, see Using iPod on page 20.

1 FUNCTION Switches between the simple remote mode and menu browse mode.

2 Center Press Center to enter the selected group. (Pressing Center starts playback when a song is selected.)

3

Skips to the beginning of the current track. Press and hold to fast reverse. Press twice to skip to the previous track.

4 DISPLAY Displays the song information while iPod is in menu browse mode (see page 16).

5

Starts or pauses playback.

6 SHUFFLE Selects the shuffle playback mode (see page 21).

7 MENU Returns to the upper level in the iPod menu.

8

Skips to the next track. Press and hold to fast forward.

9 / Press or to select an item in the selected group.

0 REPEAT Selects the repeat playback mode (see page 21).

The supplied remote control has the same function keys with your iPod. So, these keys are corresponding with each other.

STANDBY ON

CD iPod FM USB

SLEEP

FMPRESET

FUNCTION

MENU

DISPLAY

FOLDER

SHUFFLE REPEAT

MUTE VOLUME

TUNING MEMORY

4

1

3 2

5

7

8

6 0

9

iPod Remote Control

8 En

CONTROLS AND FUNCTIONS

Preparing the remote control The remote control comes with the battery already installed. Before using the remote control for the very first time, pull out the insulation sheet, as shown.

y Remove the transparent sheet before using the remote control.

Using the remote control Use the remote control within 6 m (20 feet) of the component you want to control and point it toward its remote control sensor (see page 3).

Be careful not to spill liquid on the remote control. Be careful not to drop the remote control. Do not leave the remote control in the following places:

hot or humid places, such as near a heater or in a bathroom extremely cold places dusty places

Replacing the battery in the remote control Change the battery when the operation range of the remote control decreases.

Insert the battery according to the polarity markings (+ and -). If the battery runs out, immediately remove it from the remote control to prevent an explosion or acid leak. If the battery starts leaking, dispose of it immediately. Be careful not to let the leaking battery acid touch your skin or clothing. Before inserting a new battery, wipe the compartment clean. Dispose of batteries according to your regional regulations.

Insulation sheet

Notes

STANDBY ON PHONES

VOLUME

INPUT

30 30

STANDBY ON

CD iPod FM USB

SLEEP

FMPRESET

FUNCTION

MENU

DISPLAY

FOLDER

SHUFFLE REPEAT

MUTE VOLUME

TUNING MEMORY

Within 6 m (20 feet)

Notes

Use a straight pin to remove the cover.

Replace the battery with a new CR2025 battery.

Close the cover.

CONNECTING SPEAKERS

9 En

E n

g lish

P R

E P

A R

A T

IO N

Follow the procedure below to connect speakers to this unit. For information on your speakers, refer to the owners manual supplied for the speakers.

Do not connect the power cable of this unit until all cable connections are completed.

Be sure to connect the left channel (L), right channel (R), +(red) (black) properly. If the connections are faulty, no sound will be heard from the speakers, and if the polarity of the speaker connections is incorrect, the sound will be unnatural and lacks bass.

Do not let the bare speaker wires touch each other or do not let them touch any metal part of this unit. This could damage this unit and/ or the speakers.

Use speakers with the specified impedance shown on the rear panel of this unit.

CONNECTING SPEAKERS

CAUTION

Notes

SUBWOOFER OUT

FM ANT 75 UNBAL

SPEAKERS

TUNER

MAINS

R L

Right speaker Speaker cables

Left speaker

Rear panel

CONNECTING SPEAKERS

10 En

1 Remove approximately 10 mm (3/8 in) of insulation from the end of each speaker cable and then twist the exposed wires of the cable together to prevent short circuits.

2 Press and hold the lever.

3 Insert one bare wire. By releasing the lever, the lever is replaced.

Notes on the speaker cord A speaker cord is actually a pair of insulated cables running side by side. One cable is colored or shaped differently, perhaps with a stripe, groove or ridge. Connect the striped (grooved, etc.) cable to the +(red) terminals on this unit and your speaker. Connect the plain cable to the (black) terminals on this unit and your speaker.

The low frequency range of the left channel and the right channel are mixed to output at the SUBWOOFER OUT jack.

Connect the SUBWOOFER OUT jack on this unit to the INPUT jack on the subwoofer using the subwoofer cable (commercially available).

Do not connect the power cable of this unit and the subwoofer until all cable connections are completed.

10 mm (3/8 in)

Red: positive (+) Black: negative ()

Red: positive (+) Black: negative ()

Connecting a subwoofer

Note

SUBWOOFER OUT

TUN

INPUT

INPUT

Subwoofer cable (commercially available)

Subwoofer (commercially available)

CONNECTING ANTENNAS

11 En

E n

g lish

P R

E P

A R

A T

IO N

To enjoy radio on this unit, connect the supplied FM antenna to the designated terminals. If there is a problem of weak radio wave reception in your area or you want to improve radio reception, we recommend that you use commercially available outdoor antennas. For details, consult the nearest authorized Yamaha dealer or service center.

1 Connect the supplied indoor FM antenna to the FM jack of this unit.

2 Place the antenna away from this unit and speaker cables.

After you made all connections, connect the power cables of this unit and subwoofer (optional).

You can connect your headphones to the PHONES jack on the front panel of this unit. The sound from the speakers stops.

CONNECTING ANTENNAS

SUBWOOFER OUT

FM ANT 75 UNBAL

TUNER

Indoor FM antenna (supplied)

Connecting the FM antenna

CONNECTING THE POWER CABLES

SUBWOOFER OUT

FM ANT 75 UNBAL

SPEAKERS

TUNER

6 MIN. SPEAKER

MAINS

R L

To an AC wall outlet

CONNECTING HEADPHONES

STANDBY ON PHONES

VOLUME

INPUT

CONNECTING EXTERNAL COMPONENTS

12 En

You can connect a USB device or an iPod to this unit. For information on your component, refer to the owner's manual supplied with the component.

This unit has a USB port and can access MP3 or WMA files saved on your USB device. Connect your USB device to the USB port on the top panel of this unit. For playback information of a USB device, see page 15.

Supported USB devices This unit supports USB mass storage class devices (e.g., flash memories) using FAT16 or FAT32 format.

Some devices may not work properly even if they meet the requirements.

If your USB device is not played back after you connected it to this unit, follow any of the procedures below. Set this unit to the standby mode, and turn it on again. Disconnect the device while this unit is in the standby mode. Then connect the device again and turn on this unit. Connect an AC adapter if supplied with the device.

If the USB device is not played back even after you performed the procedure(s) above, the device may not be playable on this unit.

Do not connect devices other than USB mass storages class devices.

Yamaha and suppliers accept no liability for the loss of data saved on the USB devices connected to this unit. As a precaution, it is recommended that the files are made backup copies.

Playability of and power supply to all kind of USB devices are not guaranteed.

Your USB device is automatically charged when your USB device is connected to the USB port even when this unit is in standby mode and ECO MODE is OFF.

To remove USB device safely, disconnect after the playback is stopped.

This unit equips the iPod terminal on the top panel where you can directly station your iPod and control playback of your iPod using the supplied remote control. Use this unit with the iPod dock adapter (supplied with your iPod or commercially available) appropriate for your iPod. If you use this unit without using an appropriate iPod dock adapter, loose connection may result.

Only iPod (Click and Wheel), iPod nano, iPod mini, and iPod touch are supported.

Do not connect any iPod accessories (such as headphones, a wired remote control, or an FM transmitter) to our iPod when it is stationed in the terminal.

Unless your iPod is firmly stationed in the terminal, audio signals may not be output properly.

Once the connection between your iPod and this unit is complete, iPod appears in the front panel display. If the connection between your iPod and this unit fails, a status message appears in the front panel display. For a complete list of connection status message, see the iPod section in TROUBLESHOOTING on page 23.

Your iPod is automatically charged when your iPod is stationed in the terminal even when this unit is in standby mode and ECO MODE is OFF.

To remove iPod safely, disconnect after the playback is stopped.

CONNECTING EXTERNAL COMPONENTS

Connecting a USB device

Notes

STANDBY ON PHONES

VOLUME

INPUT

USB

iPod

USB device

Connecting an iPod

Notes

STANDBY ON PHONES

VOLUME

INPUT

USB

iPod

iPod

BASIC RECEIVER OPERATIONS

13 En

E n

g lish

B A

S IC

O

P E

R A

T IO

N S

Follow the procedure below to select an input source and adjust the sound settings on this unit.

1 Press STANDBY/ON to turn on this unit. The front panel display lights up.

2 Press one of the input selection keys or press INPUT on the front panel to select the desired input source. Each time you press INPUT, the input source changes in order of CD, iPod, FM and USB.

3 Start playback on the selected source component or select a radio station. For information on the disc playback, see page 15, and for information on tuning, see page 18.

4 Press (down) / (up) to adjust the volume to the desired output level.

To adjust the audio quality

1 Press FUNCTION to display the function menu.

2 Press / repeatedly to select TREBLE, BASS, or BALANCE and press Center.

3 Press / repeatedly to adjust the setting and press Center.

TREBLE: Adjusts the high frequency response. BASS: Adjusts the low frequency response. BALANCE: Adjusts the volume level of each left

and right speaker channel.

y TREBLE, BASS, and BALANCE are not adjustable when using the headphones.

To dim the display You can dim the front panel display of this unit.

1 Press FUNCTION to display the function menu.

2 Press / repeatedly to select DIMMER and press Center. Press / to select the brightness and press Center.

To use the ECO mode This mode reduces power consumption during the standby mode. Your iPod or USB device cannot be charged during standby mode and ECO MODE is ON.

1 Press FUNCTION to display the function menu.

2 Press / repeatedly to select ECO MODE and press Center.

3 Press / to select ON or OFF and press Center.

BASIC RECEIVER OPERATIONS

STANDBY ON PHONES

VOLUME

INPUT

STANDBY ON

CD iPod FM USB

SLEEP

FMPRESET

FUNCTION

MENU

DISPLAY

FOLDER

SHUFFLE REPEAT

MUTE VOLUME

TUNING MEMORY

VOLUME INPUT

STANDBY/ON

VOLUME /

Input selection keys

FUNCTION

Center /

STANDBY/ON

SETTING THE SLEEP TIMER

14 En

The sleep timer sets this unit to the standby mode after the specified time elapses.

Press SLEEP repeatedly to select the desired duration. Each time you press the key, the duration changes as follows. The SLEEP indicator lights up in the front panel display.

y The sleep timer is canceled if you set this unit to the standby

mode. If you press SLEEP while the sleep timer is set, the remaining

time appears in the front panel display.

To cancel the sleep timer Press SLEEP repeatedly to select SLEEP OFF.

SETTING THE SLEEP TIMER

STANDBY ON

CD iPod FM USB

SLEEP

FMPRESET

FUNCTION

MENU

DISPLAY

FOLDER

SHUFFLE REPEAT

MUTE VOLUME

TUNING MEMORY

SLEEP

SLEEP 30min

SLEEP 60min

SLEEP 90min

SLEEP 120min

SLEEP OFF

BASIC PLAYBACK OPERATIONS FOR DISCS AND USB DEVICES

15 En

E n

g lish

B A

S IC

O

P E

R A

T IO

N S

You can enjoy playback your audio CDs, USB devices, and MP3 or WMA files recorded on a disc/USB device. Some operations may be different or restricted depending on the disc/USB device. Before playing back, check the compatibility of your disc/USB device with this unit (see page 25).

To start disc playback

1 Select CD as the input source (see page 13).

2 Press while a disc is loaded. For an audio CD, playback starts from the first track, and for MP3 or WMA files, playback starts in alphanumeric order by the filename.

y You can open and close the disc tray by pressing on the

front panel of this unit. You can also start disc playback by pressing on the front

panel. When the input source is CD and this unit is turned on with a

disc loaded, disc playback starts automatically.

To start USB device playback

1 Select USB as the input source (see page 13).

2 Connect your USB device to the USB port on this unit. The reading time may exceed 30 seconds depending on the number of files/folders. For a USB device, playback starts automatically in order by the date and time of creation if playable files are in the USB device.

Total time does not appear on the front panel for USB device playback.

If the USB device is partitioned, only the first partition is displayed.

Some files may not work properly depending on the USB device specification.

Copyright-protected files cannot be played back. This unit can play back files of 4 GB in size or less. When the input source is USB and this unit is turned on with the

USB device connected, playback starts automatically.

To stop playback

Press .

To pause playback

Press . To return to normal playback, press .

To fast reverse or fast forward

To fast reverse, hold down . To fast forward, hold down .

To skip tracks

To skip to the start of the current track, press . To skip to the next track, press . To skip to the previous track, quickly press twice.

To skip a folder for an MP3 or WMA file

To skip a folder, press FOLDER / .

About MP3 and WMA discs/USB device

You can play back MP3 or WMA files recorded on your CD-R, CD-RW or USB device. This unit regards files in the disc/USB device as tracks (as shown above).

BASIC PLAYBACK OPERATIONS FOR DISCS AND USB DEVICES

Notes

STANDBY ON

CD iPod FM USB

SLEEP

FMPRESET

FUNCTION

MENU

DISPLAY

FOLDER

SHUFFLE REPEAT

MUTE VOLUME

TUNING MEMORY

FOLDER /

/

Root Folder

File

BASIC PLAYBACK OPERATIONS FOR DISCS AND USB DEVICES

16 En

You can switch the disc playback information shown in the front panel display of this unit. Available information differs depending on the type of the disc/USB device.

Press DISPLAY repeatedly while playing back a disc/USB device. Each time you press the key, the information display changes as described in Playback information for audio CDs and Playback information for MP3 or WMA files recorded on discs/USB devices on page 16.

Some special characters may not be shown properly.

Playback information for audio CDs The following information is available during playback of an audio CD. Track Title, Artist, and Album Title are available only for a CD TEXT disc.

You can switch the playback information 1 2 5 6 7 above during playback of your iPod in the menu browse mode (see page 21).

Playback information for MP3 or WMA files recorded on discs/USB devices The following information is available during playback of an MP3 or WMA files recorded on discs/USB device.

Switching the playback information display

FMPRESET

FUNCTION

MENU

DISPLAY

FOLDER

SHUFFLE REPEAT

TUNING MEMORY

DISPLAY

Note

Note

SONGS

ARTISTS

ALBUMS

1 Elapsed time of the current track (Default)

2 Remaining time of the current track

3 Total time of the disc

4 Remaining time of the disc

7 Album Title

6 Artist

5 Track Title

SONGS

ARTISTS

ALBUMS

2 File Name

1 Elapsed time of the current file

4 Artist

5 Album Title

3 Track Title

BASIC PLAYBACK OPERATIONS FOR DISCS AND USB DEVICES

17 En

E n

g lish

B A

S IC

O

P E

R A

T IO

N S

You can repeat the playback of the selected item in your disc/USB device.

1 Play back the disc or track you want to repeat.

2 Press REPEAT to select the desired Repeat Play mode. Each time you press the key, the Repeat Play mode in the front panel display changes as follows.

To cancel Repeat Play Press REPEAT repeatedly so that the Repeat Play mode indicator disappears from the front panel display or press

.

You can play back tracks in your disc/USB device in random order.

When playing back with Shuffle Play, the remaining time of the disc cannot be displayed.

Press SHUFFLE. Each time you press the key, the Shuffle play mode in the front panel display changes as follows.

* The SHUFFLE FOLDER means tracks in the folder is play back in randomly.

To cancel Shuffle Play Press SHUFFLE repeatedly so that the SHUFFLE indicator disappears from the front panel display or press

.

Repeating playback (Repeat Play)

REPEAT

STANDBY ON

CD iPod FM USB

SLEEP

FMPRESET

FUNCTION

MENU

DISPLAY

FOLDER

SHUFFLE REPEAT

MUTE VOLUME

TUNING MEMORY

Audio CD

REPEAT ONE (Repeat Play by track)

REPEAT ALL (Repeat Play by disc)

Off (Normal playback)

MP3/WMA disc/USB device

REPEAT ONE (Repeat Play by track)

REPEAT FOLDER (Repeat Play in the folder)

REPEAT ALL (Repeat Play by disc)

Off (Normal playback)

Playing back randomly (Shuffle Play)

Note

STANDBY ON

CD iPod FM USB

SLEEP

FMPRESET

FUNCTION

MENU

DISPLAY

FOLDER

SHUFFLE REPEAT

MUTE VOLUME

TUNING MEMORY

SHUFFLE

SHUFFLE FOLDER*

SHUFFLE ALL

Off

Audio CD

SHUFFLE ALL

Off

MP3/WMA disc/USB device

FM TUNING

18 En

There are 2 tuning methods: automatic and manual. Automatic tuning is effective when station signals are strong and there is no interference. If the signal from the station you want to select is weak, tune into it manually. You can also use the automatic and manual preset tuning features to store up to 30 stations.

Automatic tuning is effective when station signals are strong and there is no interference.

1 Press FM to set this unit to the FM mode.

2 Press and hold TUNING / to begin automatic tuning. The AUTO indicator lights up on the front panel display. This unit automatically detects radio stations that have strong signals for your selection, and automatically ends automatic tuning. The AUTO indicator disappears from the front panel display.

If the signal received from the station you want to select is weak, tune into it manually.

1 Press FM to set this unit to the FM mode.

2 Press TUNING / repeatedly to tune into the desired station manually.

y Manually tuning into an FM station automatically switches the tuner to monaural reception to increase the signal quality.

Follow the procedure below to preset radio stations automatically.

1 Press FM to set the unit to the FM mode.

2 Press and hold MEMORY for more than 2 seconds. The AUTO PRESET and Push Center Key appear in the front panel display alternately. To cancel, press MEMORY.

3 Press Center to start searching automatically. Auto Preset starts at the lowest frequency toward

the highest frequency. This unit automatically applies a preset number to

each detected station.

4 Search will stop after finding appropriate station and stores as a preset station.

5 Search will start again to find a next station.

You can preset up to 30 of FM stations with Auto Preset. Any stored station data existing under a preset station number is

cleared when you store a new station under the same preset station number.

FM TUNING

Automatic tuning

Manual tuning

STANDBY ON

CD iPod FM USB

SLEEP

FMPRESET

FUNCTION

MENU

DISPLAY

FOLDER

SHUFFLE REPEAT

MUTE VOLUME

TUNING MEMORY

FM

TUNING /

Automatic preset tuning

Notes

STANDBY ON

CD iPod FM USB

SLEEP

FMPRESET

FUNCTION

MENU

DISPLAY

FOLDER

SHUFFLE REPEAT

MUTE VOLUME

TUNING MEMORY MEMORY

Center

FM

19 En

FM TUNING E

n g

lish T

U N

E R

O

P E

R A

T IO

N S

You can also store up to 30 stations manually.

1 Tune into a radio station you want to preset. See page 18 for tuning instructions.

2 Press MEMORY. The MEMORY and PRESET indicators light up in the front panel display until you cancel manual preset. To cancel, press MEMORY.

3 Press / repeatedly to select a preset station number.

4 Press Center while the preset station number you selected is flashing. The MEMORY indicator disappears from the front panel display.

5 Repeat steps 1 to 4 until all desired stations are preset.

You can tune into any desired station simply by selecting the preset station under which it was stored (see page 18).

1 Press FM to set the unit to the FM mode.

2 Press PRESET / to select a preset station.

To delete the preset station

1 Press FM to set the unit to the FM mode.

2 Press FUNCTION to display the function menu. Press / to select PRESET DELETE and press Center.

3 Press / to select the preset number you want to delete and press Center.

Manual preset tuning

STANDBY ON

CD iPod FM USB

SLEEP

FMPRESET

FUNCTION

MENU

DISPLAY

FOLDER

SHUFFLE REPEAT

MUTE VOLUME

TUNING MEMORY MEMORY

Center /

Selecting preset stations

STANDBY ON

CD iPod FM USB

SLEEP

FMPRESET

FUNCTION

MENU

DISPLAY

FOLDER

SHUFFLE REPEAT

MUTE VOLUME

TUNING MEMORY

PRESET /

FM

/

FUNCTION

Center

CONTROLLING iPod

20 En

In addition to controlling this unit, you can operate your iPod stationed in a terminal using the supplied remote control.

Once you have stationed your iPod in a terminal on the top panel of this unit (see page 12), you can enjoy playback of your iPod using the supplied remote control. The operations of your iPod are available with the aid of front panel display (menu browse mode) or without it (simple remote mode).

Only iPod (Click and Wheel), iPod nano, iPod mini, and iPod touch are supported. Some features may not be compatible depending on the model or the software version of your iPod.

y For a complete list of the remote control functions used to control your iPod, refer to iPod mode (see page 7). For a complete list of status messages that appear in the front panel display, refer to the iPod section in TROUBLESHOOTING

(see page 23).

Simple remote mode In the simple remote mode, you can operate the iPod menu by viewing the iPod using the iPod controls or the supplied remote control.

1 Press iPod to set this unit to the iPod mode.

2 Press FUNCTION and / to show iPod MODE on the front panel display and press Center.

3 Press / to select SIMPLE REMOTE. Press Center while SIMPLE REMOTE is blinking on the front panel display. You can also select the menu browse mode by

pressing / so, MENU BROWSE appears on the front panel display. For details, refer to page 21.

4 Use MENU/ / / Center to operate the iPod menu, and then press Center to start playback of the selected song (or group).

CONTROLLING iPod

Using iPod

Notes

STANDBY ON

CD iPod FM USB

SLEEP

FMPRESET

FUNCTION

MENU

DISPLAY

FOLDER

SHUFFLE REPEAT

MUTE VOLUME

TUNING MEMORY

/

MENU

iPod

FUNCTION Center

21 En

CONTROLLING iPod E

n g

lish O

T H

E R

O

P E

R A

T IO

N S

Menu browse mode In the menu browse mode, you can operate the iPod menu using the front panel display.

There are some characters that cannot be displayed in the front panel display of this unit. Those characters are replaced with underscore _.

iPod menu

1 Select the menu browse mode. To choose the menu browse mode, please refer to step 3 of "Simple remote mode" in page 20. The top of the iPod menu appears in the front panel display.

y The operation indicators (see page 4) show the operable cursor keys in each step.

2 Press / to select the menu, and then press Center to enter the selected menu. The name of the first item stored in the selected menu appears.

y The Multi information indicators (see page 4) show the iPod

menu currently selected. To return to the upper level in the iPod menu, press MENU.

3 Repeat step 2 until you select the desired item, and then press Center to start playback of the desired item (group or song).

y While playing back a track (or group) with the menu browse mode, you can switch the playback information (such as song name, elapsed time, artist name, or album name) displayed in the front panel display by pressing DISPLAY.

Repeating playback (Repeat Play) You can repeat playback of the selected items in your iPod.

Press REPEAT to select the desired Repeat Play mode. Each time you press the key, the Repeat Play mode changes as follows. To use properly, please check it with your iPod.

Playing back randomly (Shuffle Play) You can play back tracks in your iPod in random order.

Press SHUFFLE. Each time you press the key, the Shuffle Play mode changes as follows. To use properly, please check it with your iPod.

Note

Operation indicators

ARTISTS

One (Repeat play by song)

All (Repeat play by selected group)

Off

Songs (Shuffle play by song)

Albums (Shuffle play by albums)

Off

TROUBLESHOOTING

22 En

Refer to the table below when this unit does not function properly. If the problem you are experiencing is not listed below or if the instruction below does not help, turn off this unit, disconnect the power cable, and contact the nearest authorized Yamaha dealer or service center.

TROUBLESHOOTING

General

Problem Cause Remedy See

page

This unit fails to turn on or enters the standby mode soon after the power is turned on.

The power cable is not connected or the plug is not completely inserted.

Connect the power cable firmly. 11

This unit has been exposed to a strong external electric shock (such as lightning or strong static electricity).

Set this unit to the standby mode, disconnect the power cable, plug it back in after 30 seconds and then use it normally.

No sound No appropriate input source has been selected.

Select an appropriate input source with the INPUT on the front panel (or the input selection keys on the remote control).

Speaker connections are not secure. Secure the connections. 9

The volume is turned down. Turn up the volume.

Signals this unit cannot reproduce are being input from a source component, such as a CD-ROM.

Play a source whose signals can be reproduced by this unit.

Sound is heard from the speaker on one side only.

Incorrect cable connections. Connect the cables properly. If the problem persists, the cables may be defective.

9

There is noise interference from digital or radio frequency equipment.

This unit is too close to the digital or high-frequency equipment.

Move this unit further away from such equipment.

Radio reception

Problem Cause Remedy See page

FM

FM stereo reception is noisy.

The characteristics of FM stereo broadcasts may cause this problem when the transmitter is too far away or the antenna input is poor.

Check the antenna connections. 11

Try using a high-quality directional FM antenna.

Use the manual tuning method. 18

There is distortion, and clear reception cannot be obtained even with a good FM antenna.

There is multi-path interference. Adjust the antenna position to eliminate multi-path interference.

The desired station cannot be tuned into with the automatic tuning method.

The signal is too weak. Use a high-quality directional FM antenna.

Use the manual tuning method. 18

23 En

E n

g lish

TROUBLESHOOTING A

D D

IT IO

N A

L

IN F

O R

M A

T IO

N

In case of a transmission error without a status message appearing in the front panel of this unit, check the connection to your iPod (see page 12).

In case of a transmission error without a status message appearing in the front panel of this unit, check the connection to the USB device (see page 12).

iPod

Note

Status message Cause Remedy See

page

iPod Connecting This unit is in the middle of recognizing the connection with your iPod.

This unit is in the middle of acquiring song lists from your iPod.

Connect error There is a problem with the signal path from your iPod to this unit.

Turn off this unit and reconnect the iPod. 12

Try resetting your iPod.

Unknown iPod The iPod being used is not supported by this unit.

Only iPod (Click and Wheel), iPod nano, iPod mini, and iPod Touch are supported.

iPod Your iPod is properly stationed in an iPod terminal.

iPod Unplugged Your iPod was removed from an iPod terminal.

Station your iPod back in an iPod terminal. 12

USB

Note

Status message Cause Remedy See

page

Not Connected The USB device is not connected firmly.

Connect the USB device again. 12

Not Supported Connected the USB device not playable on this unit.

Connect playable USB device. 12

Over Current Connected the USB device not playable on this unit. Connected the USB device diagonally.

Disconnect the USB device. Change input source other than USB and select USB as input source again. Then connect playable USB device again.

12

24 En

TROUBLESHOOTING

Disc Playback

Problem Cause Remedy See

page

Power turns on but immediately shuts off.

The power cable is not connected or the plug is not completely inserted.

Connect the power cable firmly. 11

No sound or distorted sound

The sampling rate of a MP3 or WMA file may not be compatible with this unit.

Check the sampling rate and bit rate of an MP3 or WMA file are compatible with this unit.

25

Disc playback does not start.

You may use a CD-R/RW that is not finalized.

Finalize the CD-R/RW.

The disc label may not be facing up. Check that the disc label is facing up.

The disc may be defective. Try to play back another disc. If the same problem does not happen, the disc you want to play back is defective.

MP3/WMA disc may not contain sufficient music tracks to be played back.

Check that your MP3/WMA disc contains at least 5 MP3/WMA music files. If the number of files is small, the disc may not be recognized.

The sampling rate of a MP3 or WMA file may not be compatible with this unit.

Check the sampling rate and bit rate of an MP3 or WMA file are compatible with this unit.

25

USB playback does not start.

Improper USB device connections. Connect the USB device again. 12

The MP3 or WMA formats are not compatible with this unit.

Replace the file with a correctly recorded file playable with this unit.

25

Remote control

Problem Cause Remedy See

page

The remote control does not work nor function properly.

The remote control may be operated outside its operation range.

For information on the remote control operation range, refer to Using the remote control.

8

The remote control sensor on this unit may be exposed to direct sunlight or lighting (invented fluorescent lamps).

Change the lighting or orientation of this unit.

The battery may be worn out. Replace the battery with new one. 8

There are obstacles between the sensor of this unit and the remote control.

Remove the obstacles.

25 En

E n

g lish

A D

D IT

IO N

A L

IN

F O

R M

A T

IO N

Discs (audio CDs) playable with this unit This player is designed for playing back compact discs bearing the marks shown below. Never attempt to load any other type of disc into the unit. The unit can also play back 8-cm (3-inch) compact discs.

About MP3 and WMA files You can play back MP3 and WMA files recorded on a CD-R/CD-RW and those stored on a USB device.

MP3 MP3 is a standard technology and format for compressing an audio sequence into a small-sized file. However, the original level of sound quality is preserved during playback. The playable formats are: MPEG-1 Audio Layer-3

Bitrate*: 32-320 kbps Sampling frequency: 44.1/48/32 kHz

MPEG-2 Audio Layer-3, 2 Bitrate*: 8-160 kbps Sampling frequency: 24/22.05/16 kHz

* Variable bitrate is supported.

WMA WMA (Windows Media Audio) is a Microsoft file format for encoding digital audio files similar to MP3 though can compress files at a higher rate than MP3. The playable formats are: Version 8 Version 9 (Standard and variable bitrates are

supported. Professional and Lossless are not supported.)

High Profile Bitrate*: 32-320 kbps Sampling frequency: 48/44.1/32 kHz

Mid Profile Bitrate: 16-32 kbps Sampling frequency: 22.05/16 kHz

* Both constant and variable bitrates are supported.

Playback for Data Disc starts in alphanumeric order of files. Playback for USB starts in order by date and time of file

creation. Copyright-protected WMA (DRM) files cannot be played back

by this unit. The disc must be ISO9660 compatible. The maximum file and folder numbers are as follows.

* The root is counted as one of the folders.

NOTES ABOUT DISCS/MP3, WMA FILES

.... Compact discs (digital audio) The most popular discs for commercially available audio CDs.

.... CD-R,CD-RW digital audio discs Music CDs made by copying onto a CD-R or CD-RW (including MP3 or WMA format files).

Be sure to use a CD-R or CD-RW disc made by a reliable manufacture.

Be sure to use a CD-R or CD-RW disc which has at least one of the following phrases on the disc or disc case. FOR CONSUMER FOR CONSUMER USE FOR MUSIC USE ONLY

Be sure to use a finalized CD-R or CD-RW disc.

.... CD-TEXT discs The discs recorded with text data such as album titles, track titles and artist names.

This compact disc player may not be able to play back some CD-RW discs or discs on which recording was not made correctly.

To prevent a malfunction of this unit: Do not use any nonstandard

shaped disc (heart, etc.) available on the market because it might damage the unit.

Do not use a disc with tape, stickers, or paste on it. If you use such a disc, the disc may get stuck in the unit, or damage to the unit may result.

Notes

Note Notes

Data Disc USB

Maximum total number of file and folder*

512 9,999

Maximum folder number* 255 255

Maximum file number per folder

511 255

26 En

NOTES ABOUT DISCS/MP3, WMA FILES

Notes about handling compact discs Always handle a disc with care so that its surface is not

scratched.

Compact discs are not subjected to wear during playback, but damage to the disc surface when the disc is being handled can adversely affect the disc playback.

Be sure to use a felt-tip pen or similar writing tool when writing on the label side of the disc. Do not use a ballpoint pen, pencil, or other hard-tipped writing tool, as these may damage the disc and may adversely affect the disc playback.

Do not warp discs. When a disc is not being used, remove it from the unit

and store in an appropriate case. When removing or storing a disc, be careful not to

scratch the playing surface. Compact discs are not affected by small particles of

dust or fingerprints on their playing surface, but even so they should be kept clean. Wipe by using a clean, dry cloth. Do not wipe with a circular motion; wipe straight outward from the center.

Do not try to clean the discs surface by using any type of disc cleaner, record spray, anti-static spray or liquid, or any other chemical-based liquid because such substances might irreparably damage the discs surface.

Do not expose discs to direct sunlight, high temperature or high humidity for a long period of time, as these might warp or otherwise damage the disc.

To play back an 8-cm (3-inch) CD Place it in the inner recessed area of the disc tray. Do not put a normal (12-cm) CD on top of an 8-cm (3-inch) CD.

No!

Note: Do not use any lens cleaners as they may be a cause of malfunction.

27 En

E n

g lish

A D

D IT

IO N

A L

IN

F O

R M

A T

IO N

MP3 (MPEG Audio Layer-3) One of the audio compression methods used by MPEG. It employs the irreversible compression method, which achieves a high compression rate by thinning out the data of hardly audible part to the human ears. It is said to be capable of compressing the data quantity by about 1/11 (128 kbps) while maintaining a similar audio quality to music CD.

PCM (Pulse Code Modulation) A signal that is changed to digital format without compression. A CD is recorded with 16-bit sound at 44.1 kHz. This signal also has a type called Packed PCM (PPCM) that can be compressed without any loss of data.

Sampling frequency The number of sampling (process for digitalizing analog signals) per second. In principle, the higher the sampling rate, the wider the frequency range that can be played back, and the higher the quantized bit rate, the finer the sound that can be reproduced.

Track A CD can be divided into a number of segments (tracks). Each division is called a track number.

WMA (Windows Media Audio) An audio compression method developed by Microsoft Corporation. It employs the irreversible compression method, which achieves a high compression rate by thinning out the data of hardly audible part to the human ears. It is said to be capable of compressing the data quantity by about 1/22 (64 kbps) while maintaining a similar audio quality to music CD.

MPEG Layer-3 audio decoding technology licensed from Fraunhofer IIS and Thomson Multimedia.

PLAYER SECTION

Playback System CD, CD-R/RW

Laser Type ...........................................Semiconductor laser GaAs/GaAlAs Wave length............................................................................780 nm Output power ..........................................................................10 mW

Audio Performance DAC............................................................................192 kHz/24 bit

AMPLIFIER SECTION Maximum RMS output power per channel

(6 , 1 kHz, 10% THD) ...........................................20 W + 20 W Total harmonic distortion (1 kHz)

CD 10W, 6 ........................................................................ 0.03 % Output level/Impedance

PHONES (volume max) ................................................0.6 V/32

TUNER SECTION FM Tuning Range

[U.S.A and Canada models]..............................87.5 to 107.9 MHz [Other models] ..............................................87.50 to 108.00 MHz

Sensitivity FM (S/N 30 dB) ................................................... 7dBVm (EMF)

GENERAL Power Supply

[U.S.A. and Canada models]............................... AC 120 V, 60 Hz [Australia model] ................................................ AC 240 V, 50 Hz [Asia model]............................................AC 220-240 V, 50/60 Hz [China model]...................................................... AC 220 V, 50 Hz [Korea model] ..................................................... AC 220 V, 60 Hz [Taiwan model] ............................................AC 110-120 V, 60 Hz

Power consumption................................................................... 25 W Standby Power consumption*.......................................... 1 W or less Dimensions (W x H x D) .................................. 180 x 117 x 303 mm

(7-1/16 x 4-5/8 x 11-15/16 in) Weight ............................................................... 3.1 kg (6 lbs. 13 oz.)

* When ECO MODE is ON.

Specifications are subject to change without notice.

GLOSSARY

Audio information

Copyright and logo marks

iPod is a trademark of Apple Inc., registered in the U.S. and other countries. Made for iPod means that an electronic accessory has been designed to connect specifically to iPod and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.

iPod

SPECIFICATIONS

Manualsnet FAQs

If you want to find out how the CRX-330 Yamaha works, you can view and download the Yamaha CRX-330 Receiver Owner's Manual on the Manualsnet website.

Yes, we have the Owner's Manual for Yamaha CRX-330 as well as other Yamaha manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Owner's Manual should include all the details that are needed to use a Yamaha CRX-330. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Yamaha CRX-330 Receiver Owner's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Yamaha CRX-330 Receiver Owner's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Yamaha CRX-330 Receiver Owner's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Yamaha CRX-330 Receiver Owner's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Yamaha CRX-330 Receiver Owner's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.