Yamaha DPX-1000 Projector Owner's Manual PDF

1 of 45
1 of 45

Summary of Content for Yamaha DPX-1000 Projector Owner's Manual PDF

DPX1000 Digital Cinema Projector

U

OWNERS MANUAL

Explanation of Graphical Symbols

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert you to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

1 Read these instructions.

2 Keep these instructions.

3 Heed all warnings.

4 Follow all instructions.

5 Do not use this apparatus near water.

6 Clean only with dry cloth.

7 Do not block any ventilation openings. Install in accordance with the manufacturers instructions.

8 Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9 Do not defeat the safety purpose of the polarized or grounding- type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10 Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11 Only use attachments/accessories specified by the manufac- turer.

12 Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13 Unplug this apparatus during lightning storms or when unused for long periods of time.

14 Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

IMPORTANT! Please record the serial number of this unit in the space below.

Model: Serial No.:

The serial number is located on the bottom of the unit. Retain this Owners Manual in a safe place for future reference.

CAUTION RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

IMPORTANT SAFETY INSTRUCTIONS

FCC INFORMATION (for US customers only)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class B digital devices. Compliance with these require- ments provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices.

This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices.

Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit OFF and ON, please try to eliminate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by the interference.

Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA 90620.

The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.

We Want You Listening For A Lifetime

YAMAHA and the Electronic Industries Associations Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or distortion and, most importantly, without affecting your sensitive hearing. Since hearing damage from loud sounds is often undetectable until it is too late, YAMAHA and the Electronic Industries Associations Consumer Electronics Group recommend you to avoid prolonged exposure from excessive volume levels.

COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE)

Responsible Party: Yamaha Electronics Corporation

Address: 6660 Orangethorpe Avenue

Buena Park, CA90620

Telephone: 714-522-9105

Fax: 714-670-0108

Type of Equipment: Projector

Model Name: DPX-1000

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following conditions:

1) this device may not cause harmful interference, and

2) this device must accept any interference received including interference that may cause undesired operation.

See the user manual instructions if interference to radio reception is suspected.

Caution: Read this before operating this unit.

I

To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference.

Installation

Install this unit in a well-ventilated, cool, dry, clean place with at least 30 cm (1 feet) clearance on the top, right and left, and at the back of this unit away from direct sunlight, heat sources, vibration, dust, moisture, and/or cold.

Locate this unit away from other electrical appliances, motors, or transformers to avoid humming sounds. To prevent fire or electrical shock, do not place this unit where it may get exposed to rain, water, and/or any type of liquid.

Do not expose this unit to sudden temperature changes from cold to hot, and do not locate this unit in an environment with high humidity (i.e. a room with a humidifier) to prevent condensation inside this unit, which may cause an electrical shock, fire, damage to this unit, and/or personal injury.

On the top of this unit, do not place:

Other components, as they may cause damage and/or discoloration on the surface of this unit.

Burning objects (i.e. candles), as they may cause fire, damage to this unit, and/or personal injury.

Containers with liquid in them, as they may cause electrical shock to the user and/or damage to this unit.

Do not cover this unit with a newspaper, tablecloth, curtain, etc. in order not to restrict heat dissipation. If the temperature inside this unit rises too much, it may cause fire, damage to this unit, and/or personal injury.

When installing this unit on the ceiling, make sure the ceiling has sufficient strength to support this unit and the ceiling mounts for an extended period of time. Installation must be performed only by qualified service personnel.

Operation

Remove the lens cover before starting any operation of this unit to prevent the heat from staying around the lens. Operation with the cap on may cause damage to this unit.

Do not plug in this unit to a wall outlet until all connections are complete.

Only the voltage specified on this unit must be used. Using this unit with a higher voltage than specified is dangerous and may cause fire, damage to this unit, and/or personal injury. YAMAHA will not be held responsible for any damage resulting from use of this unit with a voltage other than that specified.

Do not use force on switches, knobs and/or cords.

Do not operate this unit upside-down. It may overheat, possibly causing damage.

Take care of this unit so that no foreign objects and/or liquid drop inside this unit.

To prevent damage by lightning, disconnect the power cord from the wall outlet during an electrical storm.

Do not look into the lens while this unit is turned on. It may cause serious damage to your eyesight.

Before moving this unit, press STANDBY/ON to set this unit in the standby mode, and disconnect the AC power plug from the wall outlet.

Do not attempt to modify or fix this unit. Contact qualified YAMAHA service personnel when any service is needed. The cabinet should never be opened for any reason.

When not planning to use this unit for a long period of time (i.e. vacation), disconnect the AC power plug from the wall outlet.

When disconnecting the power cord from the wall outlet, grasp the plug; do not pull the cord.

Be sure to read the TROUBLESHOOTING section on common operating errors before concluding that this unit is faulty.

Others

Clean the lens carefully so as not to create any scratches by using a blower or lens paper.

Replace the lamp when the LAMP indicator blinks in red after the lamp usage has exceeded 2000 hours. Follow the lamp replacement procedure described in this manual.

For U.K. customers

IMPORTANT THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:

GREEN-AND-YELLOW: EARTH BLUE: NEUTRAL BROWN: LIVE

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or coloured GREEN or GREEN- and-YELLOW. The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.

If the socket outlets in the home are not suitable for the plug supplied with this appliance, it should be cut off and an appropriate 3 pin plug fitted. For details, refer to the instructions described below.

Note

The plug severed from the mains lead must be destroyed, as a plug with bared flexible cord is hazardous if engaged in a live socket outlet.

For Canadian customers To prevent electric shock, match wide blade of plug to wide slot and fully insert. This Class B digital apparatus complies with Canadian ICES- 003.

E n

g lish

If this unit is not correctly installed in an appropriate place, it may cause fire or failure, or damage the unit itself. Carefully choose the place to install this unit by avoiding the places listed below.

1. Places where the temperature and humidity vary greatly

Do not install this unit in a place where the temperature and humidity become extremely high or the temperature becomes extremely low.

This unit must be used within a temperature range of 535C.

2. Places without adequate ventilation

Install this unit with at least 30 cm (1 feet) of ventilation space on the top, right and left, and back.

Do not cover the ventilation slots of this unit not to obstruct the heat dissipation.

Install this unit on the firm surface.

Do not cover this unit with a tablecloth, etc.

Make sure there is nothing to get sucked into the ventilation slots so that the temperature of this unit does not become too high.

If you are going to install the unit in a rack, be sure to leave space for ventilation to prevent exhaust overheating the unit.

3. Places where it gets dusty

If the filter is blocked with dust, the temperature of this unit may become too high.

4. Places with too much vibration or impact

Vibration and impact can damage parts of this unit.

5. Places where this unit gets exposed to water or high humidity

If this unit is exposed to water or high humidity, it may cause a fire or electrical shock.

6. Unstable places

If this unit is installed on an unstable or an inclined tabletop, it may fall and cause damage to the unit or personal injury.

7. In close proximity to a Radio or Stereo

The unit may interfere with reception if placed in close proximity to a radio or television receiver.

Important

To ensure vivid, high contrast images, make sure that no light other than the projector light falls directly on the screen.

Accessory check Please check that all accessories listed here are included in your package.

Inappropriate places for installation

II

4 5

RESET

6

1 2 3

VIDEO

STILL HIDE

INPUT

MENU

PATTIRIS

AUTO

SETTING

ASPECT

ZOOM FOCUSV. POS

ESCAPE

LIGHT

B D4

S VIDEO A

INPUT

MEMORY

DVI

Remote control Batteries (AA, UM-3 or R6)

Pin/BNC adapters

Power cable

Lens cover

E-1

IN T

R O

D U

C T

IO N

IN S

TA L

L A

T IO

N C

O N

N E

C T

IO N

S B

A S

IC O

P E

R A

T IO

N M

E N

U A

D D

IT IO

N A

L IN

F O

R M

A T

IO N

E n

g lish

ENGLISH

Features

Contents

Bright, high contrast images achieved through DLP technology

HDTV capable 1280 x 720 pixel wide DMD element

A bright, high resolution large diameter lens

Electronic lens adjustment Zoom, Focus, Vertical Position, Optical Iris Diaphragm

(DLP and DMD are trademarks of Texas Instruments.)

Low operating noise made possible by Yamaha sound technology

High quality progressive reproduction of film sources thanks to 3-2 pulldown detection

6 memory settings and an abundance of image adjustment functions

Digital Visual Interface (DVI) HDCP Compatible

INTRODUCTION

Features ............................................. 1 Part Names and Functions

Front panel and controls ....................................................... 2 Connections .......................................................................... 3 Remote control ..................................................................... 4 Using the remote control ...................................................... 5 Loading the batteries into the remote control ....................... 5 Using the remote as a wired remote control ......................... 5

INSTALLATION

Installation Installation methods ............................................................. 6 Screen and projection distance ............................................. 7 Projection image position ..................................................... 8 Keystone ............................................................................... 8

CONNECTIONS

Connecting the unit Connecting A/V components ................................................ 9 Connecting to a computer ................................................... 10

BASIC OPERATION

Basic Operations Turning on the power ......................................................... 11 Turning off the power ......................................................... 11 Preparations for projection ................................................. 12 Select an input .................................................................... 13 Select a display aspect ........................................................ 14 Other functions ................................................................... 15 Indicators ............................................................................ 15

MENU

Menu structure ................................... 16 1 ...................................................................... 17 2 .................................................................... 19 3 .................................................................... 20 4 ...................................................................... 21

Menu operation Menu screen and operating buttons .................................... 22 Basic menu operation ......................................................... 23 Submenus ........................................................................... 24 Basic submenu operation .................................................... 25 One-touch image menu ...................................................... 28 Changing the menu location ............................................... 28

Memory function Selecting the memory setting number ................................ 29 Resetting to the factory default settings ............................. 30

ADDITIONAL INFORMATION

Additional information Glossary .............................................................................. 31 Projectable signals .............................................................. 33 Message display ................................................................. 34

Maintenance Regular care ........................................................................ 35 Filter replacement ............................................................... 35 Replacing the lamp cartridge .............................................. 36

Troubleshooting .................................. 37 Specifications

Specifications ..................................................................... 38 Dimensional drawing ......................................................... 39

E-2

Part Names and Functions

1 STANDBY/ON indicator

2 STANDBY/ON button Switches the unit between Standby and On (operational) modes.

3 ESCAPE button Use this button to exit from submenu mode.

4 PATTERN button Switches the built-in test pattern display on and off.

5 ASPECT button Selects the display aspect of the projection image. Press the button to display the aspect presently being used. Pressing the button again within 2 seconds will switch the unit to the next aspect mode.

6 LAMP warning indicator

7 COVER warning indicator

Front panel and controls

STANDBY/ON

SETTING

LAMP COVER TEMP FAN

PATTERN

ESCAPE MENU

INPUT

DIGITAL CINEMA PROJECTOR DPX-1000

ASPECT

1 2

3

4

5

6

7

8 9 0

q

w e r

Front remote control sensor

STANDBY/ON indicator

Ventilation (Exhaust) vent

Lens cover

Lens

Adjuster Use this to make fine adjustments to the projection angle.

8 (Enter) button Press this button to set values and enter into submenus.

9 MENU button Press this button to display the general settings and adjustments menu.

0 SETTING button Selects the various lens adjustment modes.

q INPUT button Press this button to display the input source and input signal selection menu.

w Cursor button Use the h, g, , + buttons for functions such as system operations, menu item selection, and changing system values.

e FAN warning indicator

r TEMP warning indicator

Ventilation inlet

Lamp cover

E-3

IN T

R O

D U

C T

IO N

E n

g lish

DVI

INPUT B

RGB/YPBPR/YCBCR D4 VIDEO G/Y B/PB/CB R/PR/CR

INPUT A

HD/SYNC VD

OUT IN REMOTE RS-232C

S-VIDEO VIDEO

TRIGGER OUT

q

1 2 3 4 5 6 7 8 0 9

w e r

DVI

INPUT B

RGB/YPBPR/YCBCR D4 VIDEO G/Y B/PB/CB R/PR/CR

INPUT A

HD/SYNC VD

OUT IN REMOTE RS-232C

S-VIDEO VIDEO

TRIGGER OUT

1 INPUT B (D-Sub 15 pin) This is the input connector for signals (RGB/YPBPR/YCBCR) from a component video or RGB source. Use a D-Sub monitor cable when connecting another component to the DPX-1000 through this connector.

2 D4 VIDEO (D connector) This connector receives video signals from the D connector of other A/V components. It is compatible with the D1D4 formats. (This connector is designed for the Japanese D format only.)

37 INPUT A (BNC jacks) These are input jacks for signals from component video or RGB sources. Component signals from A/V equipment should be connected to ports 35, and RGB signals from Computer equipment to ports 37. Use a BNC cable when connecting other components to the DPX-1000 through these jacks.

3 G/Y (G, or luminance signal)

4 B/PB/CB (B, or color difference signal)

5 R/PR/CR (R, or color difference signal)

6 HD/SYNC (horizontal sync signal, composite sync signal)

7 VD (vertical sync signal)

8 S-VIDEO (Mini DIN jack) This jack receives S VIDEO signals from the S-VIDEO output jack of other A/V components. Use an S VIDEO cable when connecting other components to the DPX-1000 through this jack.

Connections

Part Names and Functions

Rear remote control sensor

9 VIDEO (Pin jack) This jack receives composite signals from jacks of other A/V components. Use a video pin cable when connecting other components to the DPX-1000 through this jack.

0 AC inlet

q DVI (DVI jack) This jack receives DVI signals from computer equipment or DVI signals from A/V equipments.

w REMOTE IN/OUT jack Connect the remote control to the IN jack when using it through a cable. Codes input through the IN jack will be output directly through the OUT jack.

e RS-232C (D-sub 9 pin) This jack is used for factory testing.

r TRIGGER OUT This jack outputs control signals to external components. A potential of 12V/Maximum 200 mA is provided when the DPX-1000 is projecting.

AC inlet Plug in the supplied power cord here.

E-4

Part Names and Functions

Remote control Buttons with identical names to those on the main unit perform identical functions. To use the remote, point it at the remote control sensor on the front or back of the unit from a distance of no more than 7 m (23 feet).

1 Transmit indicator This indicator will light up when the unit is sending infra-red signals to the main unit.

2 AUTO button Pressing this button will automatically adjust the unit to the best settings for projection by retuning the frequency of the projection to that of the source component.

3 V. POS button Switches on and off the adjustment mode for the vertical positioning of the entire image.

4 ZOOM button Switches on and off the size adjustment mode for the image being projected.

5 IRIS button Switches on and off the lens iris diaphragm change mode.

6 ESCAPE button Press this button to exit from a sub-menu.

7 Cursor buttons Use the h, g, , + buttons to move the cursor within the interface.

8 ASPECT button Selects the display aspect of the projection image. Press the button to display the aspect presently being used. Pressing the button again within 2 seconds will switch the unit to the next aspect mode.

9 STILL button Stops a moving image to display a still of the desired image. Press STILL again to cancel this function.

4 5

RESET

6

1 2 3

VIDEO

STILL HIDE

INPUT

MENU

PATTIRIS

AUTO

SETTING

ASPECT

ZOOM FOCUSV. POS

ESCAPE

LIGHT

B D4

S VIDEO A

INPUT

MEMORY

DVI

p

o

i

u

y

t

r

e

1

2

3

4

5

6

7

8

9

0

q

w

RESET

5

6

1

2

3

VIDEO

B

D4

S VIDEO

A

DVI

STILL

ASPECT

ESCAPE

HIDE

INPUT

MENU

IRIS

PATT

V. POS ZOOM

FOCUS

AUTO

4

ID -2

ID -1

a

s

0 INPUT area Directly selects the input jack.

q MEMORY area Calls up stored video memory directly.

w RESET button Press this button to reset all parameters altered in the menu to their default factory settings.

e button Switches the unit between Standby and On (operational) modes.

r FOCUS button Switches on and off the focus adjustment mode for the image being projected.

t PATT (PATTERN) button Switches the built-in test pattern display on and off.

y MENU button Press this button to display the general settings and adjustments menu.

u (Enter) button Use this button to set values and enter into submenus when the menu is being displayed. Pressing the button when the menu is not being displayed will call up the in-line menu. (see page 28.)

i INPUT button Press this button to display the input source and input signal selection menu.

o LIGHT switch Pressing this switch will light up the often used 2, 6, 8, e, y, i buttons. The lights will switch off if no operation is performed within 10 seconds.

p HIDE button Press this button to temporarily halt projection of the image being displayed. Press the HIDE button once more to cancel this function.

a Remote control code switching switch This remote control will work when it has the same code as that set on the menu. The default setting on the menu is ID-1.

s Remote control cable jack Use this jack to connect the remote control to the main unit with a cable.

E-5

IN T

R O

D U

C T

IO N

E n

g lish

Part Names and Functions

Important

Bright light, fluorescent light etc. on the remote sensor on the main unit may inhibit the normal functioning of the remote control.

The remote may not function normally if there is an obstacle blocking the signal between the remote and the remote control sensor on the main unit.

The above are approximate figures.

Using the remote control Use the remote control under the following conditions. The remote control will not function if it is used outside the angles and/or range detailed here.

Loading the batteries into the remote control

1. Remove the battery compartment cover from the back of the remote control.

2. Insert two batteries (AA, UM3, or R6 type), matching the polarity markings (+, ) on the batteries with those in the battery compartment.

3. After inserting the batteries, close the cover until it snaps into place.

Important

If the remote must be used closer to the main unit than normal, or does not always operate correctly, exchange the batteries for new ones.

Do not mix old and new, or different types of battery.

Remove the batteries if you do not plan to use the unit for a long time.

If the batteries leak, dispose of them immediately, taking care not to touch the battery fluid. If the battery fluid comes into contact with your eyes, mouth, or skin, rinse it off with water immediately and consult a doctor. Clean the battery compart- ment thoroughly before installing new batteries.

Using the remote as a wired remote control

To use the remote control as a wired remote control, use a 2P monaural miniplug to connect the remote control cable jack on the underside of the remote control to the REMOTE IN jack on the main unit.

Usable angle

30 degrees

Usable distance

7 m (23 feet)

A left/right arc of 30 degrees A vertical arc of 30 degrees

DVI

INPUT B

RGB/YPBPR/YCBCR D4 VIDEO G/Y B/PB/CB R/PR/CR

INPUT A

HD/SYNC VD

OUT IN REMOTE RS-232C

S-VIDEO VIDEO

TRIGGER OUT

4 5

RESET

6

1 2 3

VIDEO

STILL HIDE

INPUT

MENU

PATTIRIS

AUTO

SETTING

ASPECT

ZOOM FOCUSV. POS

ESCAPE

LIGHT

B D4

S VIDEO A

INPUT

MEMORY

DVI

4 5

RESET

6

1 2 3

VIDEO

STILL HIDE

INPUT

MENU

PATTIRIS

AUTO

SETTING

ASPECT

ZOOM FOCUSV. POS

ESCAPE

LIGHT

B D4

S VIDEO A

INPUT

MEMORY

DVI

7 m (23 feet)

7 m (23 feet) 7 m (23 feet)

1

3

2

RESET

5

6

1

2

3

VIDEO

B

D4

S VIDEO

A

DVI

STILL

ASPECT

ESCAPE

HIDE

INPUT

MENU

IRIS

PATT

V. POS ZOOM

FOCUS

AUTO

4

ID -1

ID -2

DVI

INPUT B

RGB/YPBPR/YCBCR D4 VIDEO G/Y B/PB/CB R/PR/CR

INPUT A

HD/SYNC VD

OUT IN REMOTE RS-232C

S-VIDEO VIDEO

TRIGGER OUT

E-6

Installation

Installation methods There are four ways to install this unit:

on a table in front of the screen. mounted on the ceiling in front of the screen. on a table behind a semi translucent screen. mounted on the ceiling behind a semi translucent screen.

Set the method you use on the 4 section of the MENU described later. (see page 21.)

Place the unit on a standard height table to project and view the image from in front of the screen. The height from the bottom of the unit to the center of the lens is 12.4 cm (4-7/8).

There are two kinds of brackets (low ceiling and high ceiling, sold separately) available which can be used to mount the unit on the ceiling. Consult your dealer for details on their use, and have installation done by either your dealer or a reputable contractor. The image on the screen is vertically reversed compared to that of a table mounted installation. In this case, please set the installation type to FRONT/CEILING in the 4 section of the menu. (see page 21.)

In this case, images are projected onto a semi translucent screen, and the viewer watches it from the reverse side. The relationship with the screen and projection distance corresponds to that for front projection. For rear projection, set the installation type to REAR/CEILING or REAR/TABLE in the 4 section of the menu. (see page 21.)

E-7

E n

g lish

IN S

TA L

L A

T IO

N

Screen and projection distance The ideal position for mounting the main unit (Projection distance [a]) depends on the size of the screen to be used (the length of a diagonal line across the screen). It is possible to adjust the projection distance within a preset range from Wide to Tele using the zoom function. Additionally, it is possible to adjust the V. POS (Vertical positioning) of the image to better suit the screen. Use the information illustrated in the figure below to determine the best position for installation.

Installation

Screen size

60 70 80 90 100 110 120 150 200

Wide (m) Tele (m)

1.8 2.88 2.1 3.36 2.4 3.84 2.7 4.32 3.0 4.8 3.3 5.28 3.6 5.76 4.5 7.2 6.0 9.6

Since the DPX-1000 is equipped with a 16:9 element, the ideal installation position for viewing images with a 4:3 screen depends on the size of the desired image projection.

1 When a standard 16:9 image completely fills the width of the screen (leaving black line at the top and bottom of the screen)

2 When the standard 4:3 image completely fills the screen

Screen size

60

80

100

120

200

Wide Tele (m), (feet, inches)

1.65 m 2.64 m 55 88

2.2 m 3.52 m 72 117

2.75 m 4.4 m 9 145

3.3 m 5.28 m 1010 174

5.5 m 8.8 m 18 2810

Projection distance

Wide Tele (m), (feet, inches)

2.2 m 3.52 m 73 117

2.9 m 4.64 m 96 153

3.65 m 5.84 m 12 192

4.4 m 7.04 m 145 231

7.3 m 11.68 m 2311 384

3 Projecting both 16:9 and 4:3 images It is possible to use the zoom function to make use of the screen efficiently for both 1 and 2 above. The projection distance in this case will be between Wide in 2 and Tele in 1. Adjust the size of the projected image using the zoom so that all images fill the screen completely. However, please be aware that adjustments to V. POS can cause the position of the image to slip.

3

60'' 80'' 100'' 150'' 200''

6.0 9.6 m (19'8" 31'6")

4.5 7.2 m (14'9" 23'7")

3.0 4.8 m (9'10" 15'9")

2.4 3.84 m (7'10" 12'7")

1.8 2.88 m (5'11" 9'5")

For a 16:9 screen

*These are theoretical numerical values. Please be aware that there may be some discrepancy in comparison to actual values.

Lens center line Screen size

Projection distance [a]

1 2

(feet, inches)

511 95 610 11 710 127 810 142 910 159 1010 174 1110 1811 149 237 198 316

Projection distance [a]

E-8

Installation

Projection image position Follow the instructions below to adjust the position of the projected image on the screen.

This figure shows the limits within which the zoom function can alter projection distance in relation to the screen size. Within these limits, it is possible to adjust the image so that it fills the screen completely. (See page 12.)

It is possible to adjust the vertical position of the projected image on the screen up or down by half the height of the screen. For example, shifting V. POS fully up will bring the lower limit of the image above the centerline of the lens. (See page 12.)

When this unit is mounted on a tabletop, the position of the image can be adjusted by using the adjusters located on the underside of the unit. Adjust the height by rotating the movable part of the two screw-type adjusters at the front bottom of the case. The adjustment range of these adjusters is 3 cm (1-1/4 inch). Adjust with care as loosening them further may cause them to separate from the main unit.

Keystone When the unit is mounted at an angle to the screen, the image will be projected in a trapezoid manner. Use the keystone function in the keystone section of 4 in the menu to rectify this. (See page 21.)

Tele

Lens center line

Shifted fully down

Shifted fully up

Lens center lineProjected image

Wide

E-9

C O

N N

E C

T IO

N S

E n

g lish

DVI

INPUT B

RGB/YPBPR/YCBCR D4 VIDEO G/Y B/PB/CB R/PR/CR

INPUT A

HD/SYNC VD

OUT IN REMOTE RS-232C

S-VIDEO VIDEO

TRIGGER OUT

G/Y R/PR/CRB/PB/CB

Note

Make sure to match the Y/PB/PR or Y/CB/CR of the A/V component and this unit when connecting a component to INPUT A compo- nent jacks. Also, refer to the operation instructions for the A/V component. HD/SYNC and VD need to be connected for RGB video signals in some cases.

Connecting the unit Make sure that the power of this unit and all other components is turned off before making any connections.

Some components have different connection methods and connector names. Refer to the operating instructions for each component that you wish to connect.

Plug the unit in correctly to prevent it from creating noise or other problems.

Connecting A/V components As shown in the illustration below, there are 5 types of connections provided on this unit for connection to A/V components. Follow the instructions on the figure below to connect A/V video outputs from other components to this unit using the correct cables and adapters.

D connector cable

D-sub monitor cable

BNC cable for component connection

Pin/BNC adapters

Pin cable

Video pin cable

S video cable

D14 output connectors

Pin jacksD-sub

Component/RGB video output connectors

Image output from A/ V components

BNC jacks S video output jack

Video output jack

Input

VIDEO S-VIDEO INPUT A INPUT B D4 VIDEO DVI

Signal type

Composite video S video Component video/RGB video Component video/RGB video Component video Component video/RGB video (digital)

Connector type

Pin jack Mini DIN connector BNC connector x 35 D-sub 15 pin D connector DVI connector

DVI cable (digital)

DVI output connector

E-10

DVI

INPUT B

RGB/YPBPR/YCBCR D4 VIDEO G/Y B/PB/CB R/PR/CR

INPUT A

HD/SYNC VD

OUT IN REMOTE RS-232C

S-VIDEO VIDEO

TRIGGER OUT

Connecting to a computer There are three ways of connecting a computer, as listed below. Please use the correct type of cable for the connector when making connec- tions.

Connecting the unit

Note

Refer to see 2 in the menu described on page 19 for detailed settings for the type of image signal input.

DVI cable (Digital)

D-Sub monitor cable

BNC monitor cable

Monitor output terminal

DVI output terminal

Computer

Input

INPUT A INPUT B DVI

Signal type

RGB Analog RGB Analog RGB Digital

Connector type

BNC jack x 5 D-sub 15 pin DVI connector

E-11

B A

S IC

O P

E R

A T

IO N

E n

g lish

Basic Operations This section describes the basic operation of the DXP-1000 once installation and connection have been completed. It is necessary to make detailed settings in the menu described later so that the DXP-1000 is correctly set for the mounting, screen, input signals, and other condi- tions of its installation. Follow the steps described in this section to carry out these procedures.

Turning on the power Be sure to remove the lens cover before using this unit.

1. Plug the supplied power cord into the AC inlet on the rear of the DXP-1000, then plug the cord into the wall outlet. The STANDBY/ON indicator will turn orange.

2. Press the STANDBY/ON button (The button on the remote control). The indicator will blink green and the lamp inside the unit will light up, in preparation for projection.

Note

There are STANDBY/ON indicators located on the front panel and the control panel of the main unit.

3. After approximately 35 seconds, the indicator will stop blinking, indicating that preparations for projec- tion are complete.

Important

Be sure not to disconnect the power cord while the power STANDBY/ON indicator is green, or blinking green. This can cause significant damage to the lamp and may result in a shorter lamp life or failure.

STANDBY/ON indicator

DVI

INPUT B

RGB/YPBPR/YCBCR D4 VIDEO G/Y B/PB/CB R/PR/CR

INPUT A

HD/SYNC VD

OUT IN REMOTE RS-232C

S-VIDEO VIDEO

TRIGGER OUT

STANDBY/ON

SETTING

LAMP COVER TEMP FAN

PATTERN

ESCAPE MENU

INPUTASPECT

STANDBY/ON indicator

AC inlet

INPUT

MENU

PATTIRIS

AUTO

SETTING

ASPECT

ZOOM FOCUSV. POS

ESCAPE

STANDBY/ON

SETTING

LAMP COVER TEMP FAN

PATTERN

ESCAPE MENU

INPUTASPECT

STANDBY ON ( )

Turning off the power

1. Press the STANDBY/ON button when finished using this unit.

There will be a message to confirm that you wish to turn the unit off. Press the STANDBY/ON button once more to confirm that you wish to do so. The lamp will switches to a half-lit state, and the fan continues for roughly 2 minutes to cool the lamp. During this time, the STANDBY/ON indicator blinks orange. You cannot turn the unit on again by pressing the STANDBY/ON button during this time.

Note

The lamp may blink when in the half-lit state. This is not a lamp failure.

2. Once cooling is completed, the STANDBY/ON indicator will cease blinking, becoming a steady orange.

Important

Do not disconnect the power cord when the fan is going and the STANDBY/ON indicator is blinking orange. This could damage the lamp and result in shorter lamp life or lamp failure.

3. Replace the lens cover and disconnect the unit from the power outlet if you do not plan to use it for a long time.

Important

Condensation may appear on the unit if the temperature of the surround environment changes quickly. Condensation may also cause the projected image to be cloudy. Switch off the unit power until the condensation disappears. Switching the unit on when condensation is present may damage the unit.

Press again for standby.

E-12

Basic Operations

Preparations for projection Carry out the adjustments necessary to the projection image to obtain the optimum setting for projection.

The initial setting on this unit is for projection of the image in a line directly from the center of the lens. Where the center of the screen is above or below the center of this line, use the V. POS function to adjust the vertical position of the image up or down. V. POS can adjust the image up to half the height of the screen.

1. Press the V. POS button on the remote control or the SETTING button on the main unit repeatedly to place the unit in vertical position adjustment (Lens shift) mode.

2. Adjust the image to a suitable position by pressing either the h or g buttons.

3. Press the V. POS button again or the ESCAPE button to exit from the vertical position adjustment mode.

Enlarge or reduce the size of the image to fit the size of the screen. The maximum extent of this zoom is 1:1.6.

1. Press the ZOOM button on the remote control or the SETTING button on the main unit repeatedly to place the unit in zoom adjustment (Zoom) mode.

2. Adjust the image to a suitable size by pressing either the h or g buttons.

3. Press the ZOOM button again or the ESCAPE button to exit from the adjustment mode.

Adjust the focus of the projected image.

1. Press the PATT button on the remote control or the PATTERN button on the main unit to display a test pattern for adjustment.

2. Press the FOCUS button on the remote control or the SETTING button on the main unit repeatedly to place the unit in focus adjustment mode.

3. Adjust the unit to an optimal focus setting by press- ing either the h or g buttons.

4. Press the FOCUS button again or the ESCAPE button to exit from the focus adjustment (Focus) mode.

This unit is equipped with an IRIS function to switch between the high levels of black and high contrast images important in a home theatre and the bright images needed for a large screen. Use this function as best suits your needs.

1. Press the IRIS button on the remote control or the SETTING button on the main unit repeatedly to place the unit in iris diaphragm adjustment (Iris) mode.

2. Adjust the unit to an optimal iris setting by pressing either the + or buttons.

3. Press the IRIS button again or the ESCAPE button to exit from the iris adjustment mode.

This unit is equipped with three test patterns: a crosshatch pattern useful for focus adjustment, and gray scale and color bar patterns for image adjustment. Use them as best suits your needs.

1. Press the PATT button on the remote control or the PATTERN button on the main unit to display a test pattern for adjustment.

2. Select a suitable test pattern by pressing either the + or buttons.

3. Press the PATT button again or the PATTERN button on the main unit to exit from the adjustment mode.

INPUT

MENU

AUTO

SETTING

ASPECT

ESCAPE

PATTIRIS

ZOOM FOCUSV. POS

PATTIRIS

FOCUSV. POS

ZOOM

ESCAPE

STANDBY/ON

SETTING

LAMP COVER TEMP FAN

PATTERN

ESCAPE MENU

INPUTASPECT

SETTING

ESCAPE

E-13

B A

S IC

O P

E R

A T

IO N

E n

g lish

Select an input Press the INPUT button to display the input selection menu on the screen. Use the h and g to select a name from those on display and then press the to confirm your choice. The signal settings for INPUT A, INPUT B and DVI will not change. To change them, press the + button to open the submenu, use the cursor buttons to select a suitable source from Component/ RGB PC/RGB TV, and confirm the selection by pressing the button. You can select the terminal name directly from the input area on the remote control.

Basic Operations

Input source The image signal to project

VIDEO Composite video signals input from an A/V component to the VIDEO jack

S-VIDEO S video signals input from an A/V component to the S VIDEO jack

INPUT A Component signals input to INPUT A (BNC jack)

RGB signals input from a computer to INPUT A (BNC jack)

RGB signals input from an A/V component to INPUT A (BNC jack)

INPUT B Component signals input to the D-sub 15-pin connector on INPUT B

RGB signals input from a computer to the D-sub 15-pin connector on INPUT B

RGB signals input from a component to the D-sub 15-pin connector on INPUT B

DVI Digital component signals input from an A/V component to the DVI connector

Digital RGB signals input from a computer to the DVI connector

Digital RGB signals input from an A/V component to the DVI connector

D4 VIDEO Component signals input from an A/V component to the D4 video connector

INPUT area

4 5

RESET

6

1 2 3

VIDEO

STILL HIDE

INPUT

MENU

PATTIRIS

AUTO

SETTING

ASPECT

ZOOM FOCUSV. POS

ESCAPE

LIGHT

B D4

S VIDEO A

INPUT

MEMORY

DVI

STANDBY/ON

SETTING

LAMP COVER TEMP FAN

PATTERN

ESCAPE MENU

INPUTASPECT INPUT

+

Input signal

VIDEO

S VIDEO

INPUT A

INPUT B

DVI

D4

Component

RGB PC

RGB TV

Enter

Note

Setting a laptop or notebook PC to display simultaneously on its built in display and on an external monitor can cause the image to be incorrectly displayed on the external monitor. In this case, set the PC to display on the external monitor only. Refer to the computers operating instructions for further details.

E-14

Basic Operations

Select a display aspect Display aspect selects the type of image to display for an input signal. Press the ASPECT button and select a suitable mode. The types of aspect mode available depend on the input signal. Additionally, this unit has an auto mode that can automatically select the correct display aspect if the relevant information is encoded in the input signal. These modes are accessible from the display aspect area of the 2 section of the menu described later.

1 Auto (Zoom) In this mode, when the input signal is letterbox or squeeze type, and such information is encoded in the input signal, the unit will detect this and automatically change to the most appropriate display aspect.

2 Normal In this mode, the aspect from the input signal is kept as is, and the image is projected vertically with an aspect of 16:9, filling the screen and leaving a black area to the left and right of the image.

3 Squeeze This mode displays images that have been compressed horizontally in a normal wide aspect manner.

4 Smart Zoom This mode stretches the left and right edges of a 4:3 image without altering the center, to project a 16:9 image which fills the screen.

5 Zoom This mode projects images received in a letterbox format in a 16:9 format that completely fills the screen.

6 Subtitle Zoom This mode is most appropriate for showing subtitled letter box format video software. There are more detailed settings for this mode, which can be adjusted in the Subtitle Zoom area of the 2 section of the menu. Refer to page 24 for details.

Subtitle Area Adjust the settings for subtitles.

V Scroll Adjust the position of the subtitles by moving the screen vertically.

7 Through This mode displays the signal as it is input with no enlargement or reduction. The projected image size will vary according to the resolution of the signal.

8 Through Squeeze This mode expands the width of the input signal to display the image in a 16:9 aspect. The projected image size will vary according to the resolution of the signal.

[Representative examples]

Input signal type

Standard 4:3 image

Letter box

Squeeze (Vista size)

Squeeze (Cinemascope size)

HDTV

RGB PC

Input image Display aspect

Normal

Smart Zoom

Zoom

Subtitle Zoom

Squeeze

Through Squeeze

Squeeze

Normal

Normal

Projected image

SUBTITLE

E-15

B A

S IC

O P

E R

A T

IO N

E n

g lish

Basic Operations

Other functions

STILL freezing the image Press the STILL button on the remote control to capture a frame from a moving image. Press STILL once more to resume normal projection.

HIDE turning off the image temporarily Press the HIDE button on the remote control to temporarily turn of the projected image. Press the HIDE button once more to resume normal projection.

Indicators There are 5 indicators on the main unit that display the operating status of the DPX-1000.

1 STANDBY/ON (There is also an LED on the front panel of the main unit.) Off The power is turned off. Steady orange Standby mode Blinking green Startup mode Steady green Operating Blinking orange Lamp cooling prior to going into Standby

mode Blinking red Blinks red or red and orange when there

is a problem with the fans in the unit. Consult a Yamaha dealer if this occurs.

2 LAMP Off Normal Blinking orange Lamp usage has exceeded 2000 hours. Steady red The lamp has burnt out.

3 COVER Off Normal Steady red Either the lamp cover or the filter cover is

not correctly attached.

4 TEMP Off Normal Steady red Either the internal temperature of the unit

or the temperature of the lamp is abnormally high.

5 FAN Off Normal Steady red The cooling fan is not working properly.

4 5

RESET

6

1 2 3

VIDEO

STILL HIDE

INPUTASPECT

LIGHT

B D4

S VIDEO A

INPUT

MEMORY

DVI

STILL

4 5

RESET

6

1 2 3

VIDEO

STILL HIDE

INPUTASPECT

LIGHT

B D4

S VIDEO A

INPUT

MEMORY

DVI

HIDE

STANDBY/ON

SETTING

LAMP COVER TEMP FAN

PATTERN

ESCAPE MENU

INPUTASPECT

1

3 4

52

E-16

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg hg hg hg hg

hg hg hg hg

hg hg hg

hg hg

hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg hg

Move Menu Window

Image

Black Level

Off L ML MH H

A B C D E

Memory 1 VIDEO

0

White Level 0

Gamma Trim

Hue 0

Saturation 100

Color Temp.

Sharpness Type

Sharpness Gain

Level adjustment

Iris

Color Balance

16

Signal Initial Setup

6000K +0.000uv

Standard

Standard Cinema

Location

Keystone

Remote Control Sensor

Remote Control ID

Lens Adjustment Lock

White Boost

Economy Mode

Menu Color

Message

Trigger Out

Baud Rate

Menu structure

1 These menu items make adjustments to the projection image. The menu details will vary depending on the input signal type.

2 These menu items set parameters for the various input signals. The menu details will vary depending on the input signal type.

3 These menu items set the initial parameters for a number of menu items.

4 These menu items set parameters related to installation method, remote control and so on.

Black Level (Brightness)

White Level (Contrast)

Gamma Trim

Hue

Saturation

Color Temp.

Sharpness Type

Sharpness Gain

Color Balance

Level adjustment

Iris

Display Aspect

3D Y/C Separation

Noise Reduction

Video Type

Progressive Mode

Color Space Conversion

Setup Level (SDTV)

Setup Level (HDTV)

Signal Level

Sync Adjustment

Tracking

Horiz. Display Position

Vert. Display Position

Signal Status

Color System

INPUT A Signal

INPUT A Sync Type

INPUT B Signal

INPUT B Sync Type

DVI Signal

Auto Power Off

Auto Input Search

Display Language

Lamp Running Time

Reset

Menu Start Screen

Menu Item

Menu Group

Items with a submenu

It is necessary to set various properties on a variety of menus so that this unit can project in optimal condition. There are four menu groups, each with a number of different menu items. Some of these items are not selectable for certain types of input signal, some have submenus attached, and others have a three stage menu hierarchy. (Displayed with a S overleaf.)

Each menu group consists of the items below. Follow the procedures outlined to adjust the parameters in each menu to suit your viewing requirements.

E-17

M E

N U

E n

g lish

Menu Item

BLACK LEVEL Adjusts the level of blackness in an image while maintaining peak white brightness. Increasing the black level will increase the luminosity of dark scenes and clarify picture tone, however it will also lower the contrast. Reducing the black level will increase the contrast in dark scenes but will reduce the clarity of black tones.

WHITE LEVEL (*CONTRAST) Increases the level of whiteness in an image without changing the luminosity of the darker parts of the image. Increasing the white level will brighten the white areas of an image and increase contrast, however it will also reduce the clarity of white within the image. Reducing the white level will lower contrast.

(*BRIGHTNESS) Controls the total brightness of an image. When set too high, the black portion of the image becomes grayish and the white portion of the image tends to be saturated. When set too low, the entire image becomes darker.

GAMMA TRIM Adjusts the response of the color gradation and gray scale within the image. There are ten patterns available, on two pages of five patterns each. Use the key to switch between the pages, and select the appropriate pattern for the contents to be viewed.

HUE Adjusts the hue of the image. Reducing this setting increases the amount of red in the image. Increasing it will add blue to the image.

SATURATION Adjusts color depth. Reducing the value of this setting lightens the color of the image, while increasing it will increase the depth of color.

COLOR TEMP. S Adjusts the level of white in colors between red and blue, and between green and magenta. A lower setting adds more red to the colors giving a more relaxed feel to the image, while a higher setting adds more blue, resulting in fresh color tones. Also, increase the hUV to give more green to the image, or reduce it to add more magenta.

Adjustment range

100 to 0 to +100

100 to 0 to +100 (*0.50 to 1.00 to 1.50)

100 to 0 to +100

A/B/C/D/E a/b/c/d/e

100 to 0 to +100

0 to 100 to 200

5000K to 6000K to 10000K (COLOR TEMP.) 0.020UV to 0.000 to +0.020UV (hUV)

1 ........ You cannot adjust these settings without an input signal.

Input signal

Video/Component, RGB TV

Video/Component, RGB TV, *RGB PC

*RGB PC

Video/Component, RGB TV, RGB PC

Video/Component, RGB TV

Video/Component, RGB TV

Video/Component, RGB TV, RGB PC

+

COLOR TEMP. ADJUSTMENT

Color temp. adjustment

Menu structure

BLACK LEVEL

White White

Output image

Black BlackWhite White Input signal Input signal

WHITE LEVEL (*CONTRAST)

White

Black White Input signal

(*BRIGHTNESS)

hUV

E-18

Adjustment range

OFF/L/ML/MH/H

0 to 16 to 63

STANDARD/RGB/ RGBYCM

50 to 0 to +50

STANDARD/CINEMA

Input signal

Video/Component, RGB TV

Video/Component, RGB TV

Video/Component, RGB TV, RGB PC

Component, RGB TV, RGB PC

Video/Component, RGB TV, RGB PC

Menu Item

SHARPNESS TYPE Use this parameter to change the filtering characteristics of the circuitry used to sharpen edges in the projected image.

SHARPNESS GAIN Adjusts the clearness of the image edges. The higher value creates clearer edges. The lower value creates a softer image with less noise element.

COLOR BALANCE S The default setting displays a good balance of colors, which you cannot change. For RGB, this parameter adjusts the color balance and gain for the three primary colors R (red), G (green), and B (Blue). The intermediate colors Y (yellow), C (cyan), and M (magenta) are set automatically based on the RGB and color temperature settings. From the RGB submenu, press the RESET key on the remote control to automatically adjust the RGB setting and based on the color gain and temperature you have just set For RGBYCM, you should set the color balance and gain for each color separately. From the RGBYCM submenu, press the RESET key on the remote control to automatically adjust the RGB or YCM tone and based on the color gain and temperature you have just set. Refer to the color chart below for further help in adjusting parameters.

LEVEL ADJUSTMENT S Adjusts gain and offset for all parameters (Y, CB, CR/R, G, B) of component and RGB signals. (except DVI input)

IRIS IRIS set this parameter to STANDARD for viewing bright images on a large screen. Set it to CINEMA if you want to give priority to the deep blacks and high contrast important to home theatre viewing.

XYZ color system color chart

Menu structure

Y

X

Green

Red

Cyan

Yellow

Magenta

Blue

E-19

M E

N U

E n

g lish

Menu structure

Selections

AUTO/NORMAL/ SQUEEZE/SMART ZOOM/ZOOM/ SUBTITLE ZOOM S (SUBTITLE AREA, V. SCROLL) THROUGH/ THROUGH SQUEEZE

0 to 3 to 10 10 to 4 to +10

OFF/ON

OFF/1/2/3

DVD/VCR

AUTO/VIDEO

AUTO/SDTV/HDTV

0%/7.5%

0%/7.5%

16235/0255

128 to 0 to +127

0 to 16 to 31

50 to 0 to +50

50 to 0 to +50

Input signal

Video/Component, RGB TV, RGB PC

Video(NTSC)

Video/Component, RGB TV

Video

Video/Component, RGB TV

Video/Component,

Video/Component, RGB TV

Video/Component, RGB TV

RGB TV

*RGB PC

*RGB PC

*RGB PC

*RGB PC

Video/Component, RGB TV, RGB PC

2 ...... You cannot adjust the parameters below if the unit is not receiving an input signal.

100

0

%

IMAGE SIGNAL

BLACK LEVELPEDESTAL LEVEL

Menu Item

DISPLAY ASPECT S Sets the aspect ratio to use when projecting an image for a given input signal. Under AUTO mode, the unit will automatically switch to the most suitable mode for display. NORMAL (THROUGH) mode projects the image as is without an alteration to the signal. SQUEEZE displays horizontally compressed images in a normal non-compressed manner. ZOOM projects the image scaled up by a given ratio. SMART ZOOM expands a 4:3 image to 16:9 size. SUBTITLE ZOOM displays subtitles. THROUGH SQUEEZE displays an image with the width scaled up. The availability of these options depends on the type of input signal.

Depending on the state of the input source, it may not be possible for the unit to automatically select the optimal display mode. In this case, please select an appropriate mode manually. SUBTITLE ZOOM contains the following parameter settings:

SUBTITLE AREA: Adjusts the subtitle display area V. SCROLL: Adjusts the vertical position of subtitles

3D Y/C SEPARATION Suppresses the rainbow like color crossing and annoying dots in the image received from video input. This choice is only available for NTSC format signals from composite inputs.

NOISE REDUCTION Uses digital processing to eliminate noise in the luminance and color signals in sources with a comparatively large amount of noise, producing a more vivid image. Use where warranted by source quality.

VIDEO TYPE To ensure synchronization, select VCR when using analog videotape as a video input source. Select DVD for other sources.

PROGRESSIVE MODE Switches the mode of interlace/progressive (I/P) conversion for the built in Faroudja function. AUTO distinguishes film source automatically and projects it progressively at 60 frames per second. Video turns the distinction function off. Both of these modes use the DCDi function. (Only for SDTV interlaced signals)

COLOR SPACE CONVERSION Selects color space coefficients for SDTV BT.601 and HDTV BT.709 type signals. In the AUTO mode, the unit will automatically select an appropriate mode based on the resolution of the signal.

SETUP LEVEL (SDTV) Compensates for the differences in blackness levels in normal image signals. It sets the level for signals equal to the pedestal level at 0%, and those for signals with high levels of blackness at 7.5%.

SETUP LEVEL (HDTV) Compensates for the differences in blackness levels in HDTV signals. It sets the level for signals equal to the pedestal level at 0%, and those for signals with high levels of blackness at 7.5%.

SIGNAL LEVEL The function to change the range of the digital signal level of the input image. Use 16235 for a standard STB (Set Top Box) connection, or use 0255 for a PC compatible connection. (Only for DVI Signals)

SYNC ADJUSTMENT Regulates flickering, noise, and disorder in the projection image. (* except DVI input)

TRACKING Regulates vertical striping in the image. (* except DVI input)

HORIZ. DISPLAY POSITION Adjusts the horizontal positioning of the projection image. (* except DVI input)

VEAT. DISPLAY POSITION Adjusts the vertical position of the projection image. (* except DVI input)

SIGNAL STATUS S Displays the resolution of the input signal, and synchronization information for RGB signals.

E-20

Menu structure

3

INPUT A INPUT B D4 VIDEO S VIDEO VIDEO DVI

Menu item

COLOR SYSTEM S Selects the color system to use when the input signal is from a video source. Available selections are NTSC, NTSC4.43, PAL, PAL-M, PAL-N, PAL60, and SECAM. Usually, setting the unit to AUTO will result in the unit automatically selecting the appropriate color method. However, since the unit does not automatically detect NTSC4.43 under AUTO mode, set the color method to NTSC4.43 manually to view NTSC4.43 images.

INPUT A SIGNAL S Selects the type of input signal received at INPUT A.

INPUT A SYNC TYPE S Selects the sync mode of the input signal received from INPUT A. (For RGB TV only)

INPUT B SIGNAL S Selects the type of input signal received at INPUT B.

INPUT B SYNC TYPE S Selects the sync mode of the input signal received from INPUT B. (For RGB TV only)

DVI SIGNAL S Selects the type of input signal received at DVI.

AUTO POWER OFF Setting the power saving mode to ON will cause the unit to automatically turn off the lamp and place itself in the standby mode if no signal is received through the inputs on the main unit for 30 minutes.

AUTO INPUT SEARCH Automatically searches through input sources in the following order if no input signal is received at the currently selected input.

DISPLAY LANGUAGE S Selects the language to use in the menu display.

LAMP RUNNING TIME S Displays the total lamp running time. You can reset the lamp running time in the submenu attached to this menu item.

RESET S Resets all parameters on the menu and held in memory to their default factory settings.

Selections

AUTO/NTSC/NTSC4.43/PAL/PAL-M/ PAL-N/PAL60/SECAM

COMPONENT/RGB PC/RGB TV

AUTO/Separate Sync/Composite Sync/ Sync on Green

COMPONENT/RGB PC/RGB TV

AUTO/Separate Sync/Composite Sync/ Sync on Green

COMPONENT/RGB PC/RGB TV

OFF/ON

OFF/ON

/English/Deutsch/Espaol/Franais/ Italiano/Portugusa/ /

ALL SETTINGS/ALL MEMORIES/ CURRENT MEMORY

E-21

M E

N U

E n

g lish

Menu structure

4

Selections

FRONT/TABLE, FRONT/CEILING, REAR/ TABLE, REAR/CEILING

100 to 0 to +100

FRONT&REAR/FRONT/REAR/OFF

ID 1/ID 2

OFF/ON

OFF/ON

OFF/ON

MONOTONE/COLOR

OFF/ON

LAMP/FAN/RS-232C

9600bps/19200bps/38400bps/57600bps/ 115200bps

Increase the value in the positive (+) direction

When the upper part of the image is wider than the lower When the lower part of the image is wider than the top

Decrease the value in a negative () direction

Menu item

LOCATION S There are four ways of installing this unit; tabletop or ceiling mounting for front or rear projection. The DPX-1000 will invert or rotate the projection according to this setting.

KEYSTONE If the projection unit is at a horizontal or perpendicular angle to the screen the projection image will be distorted to a trapezoid shape. Use the KEYSTONE setting to electronically correct without increasing the length of the image. Increase the value when the top of the image is overly wide, and reduce the value when the lower part of the image is too wide.

REMOTE CONTROL SENSOR S Use this parameter for switching between the 2 sensors located on the front and rear of the main unit that receive signals from the remote control. You can operate the main unit with a wired remote regardless of how this parameter is set.

REMOTE CONTROL ID S The main unit can receive commands from the remote control if you set the same ID in the main unit as is set by the code change switch on the side of the remote control. Use this code change switch to allow one remote to control two main units independently.

LENS ADJUSTMENT LOCK Locks the lens so that the V. POS, ZOOM, and FOCUS settings cannot be changed accidentally. Set to OFF to cancel this function.

WHITE BOOST Enhances the luster of the white part in the projected image.

ECONOMY MODE Lowers power supply to the lamp by approximately 20% to prolong its life.

MENU COLOR S Selects the color of the characters and background for the on-screen menu display. Press the + or button to access the submenu and change color selections.

MESSAGE Set whether to display messages of any type on screen.

TRIGGER OUT S Set the external control TRIGGER OUT terminal 12V signal emission to LAMP to synchronize it to the ON/OFF state of the lamp, to FAN to synchronize it to the fan, and to RS-232C, to receive ON/ OFF signals through the RS-232C terminal.

BAUD RATE S Sets the transmission speed of the RS-232C terminal. This setting becomes valid from the next time you switch the unit on.

E-22

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg hg hg hg hg

hg hg hg hg

hg hg hg

hg hg

hg

hg hg

hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg hg

Move Menu Window

Image

Display Aspect

Memory 1 VIDEO

3D Y/C Separation

Noise Reduction

Video Type

Progressive Mode

Color Space Conversion

+: Enter

Initial Setup

Setup Level (SDTV)

Signal Status

Off On

DVD VCR

Auto

VideoAuto

0% 7.5%

Setup Level (HDTV) 0% 7.5%

1 2 3

Auto SDTV HDTV

Off

Signal

Auto

Normal

Squeeze

Smart Zoom

Zoom

Subtitle Zoom

Through

Through Squeeze

Display Aspect

Menu operation

Menu screen and operating buttons This section provides you with general information about the menu screen and operating buttons on the remote control and this units control panel for easier operation. Please read it carefully before starting to operate the menu.

There are four menu groups in the menu, each containing various menu items. Some menu items also have submenus, making up a 3 tier hierarchy.

MOVE MENU WINDOW

Menu group

Menu item

Help message Memory setting number Input signal

Submenu parameter

Submenu mark

Parameter

1 MENU button Opens or closes the menu.

2 Cursor buttons +/ (for side-to-side movements)

Select a menu group.

Open and close submenus.

Select or change settings. h/g (for up and down movements)

Select a menu item.

Select or change settings.

3 button

Opens a submenu.

Confirm a new setting when adjusting COLOR SYS- TEM, INPUT A SIGNAL, INPUT B SIGNAL, DVI SIGNAL, LOCATION, REMOTE CONTROL SENSOR, or REMOTE CONTROL ID.

Opens a one-touch image menu when the menu screen has not been opened.

4 MEMORY buttons 16 (Remote control only) Select a memory setting number.

5 ESCAPE button

Returns the cursor to the menu group hierarchy from the menu item hierarchy.

Closes the submenu.

Closes the menu when the cursor is on one of the menu groups.

Returns the cursor to the menu input screen after changing menus.

6 RESET button (Remote control only) Resets the parameter setting to the factory setting. (Items without factory settings cannot be reset.)

4 5

RESET

6

1 2 3

VIDEO

STILL HIDE

INPUT

MENU

PATTIRIS

AUTO

SETTING

ASPECT

ZOOM FOCUSV. POS

ESCAPE

LIGHT

B D4

S VIDEO A

INPUT

MEMORY

DVI

5 1

2

3

4

6

STANDBY/ON

SETTING

LAMP COVER TEMP FAN

PATTERN

ESCAPE MENU

INPUTASPECT

1

3

5

2

E-23

M E

N U

E n

g lish

Menu operation

Basic menu operation To ensure proper projection, start with setting and adjustment in menu group SETUP.

4 5

RESET

6

1 2 3

VIDEO

STILL HIDE

INPUTASPECT

LIGHT

B D4

S VIDEO A

INPUT

MEMORY

DVI

INPUT

PATTIRIS

AUTO

SETTING

ASPECT

ZOOM FOCUSV. POS

ESCAPE MENU

1, 6 5

3, 5

2, 4 4

STANDBY/ON

SETTING

LAMP COVER TEMP FAN

PATTERN

ESCAPE MENU

INPUTASPECT

1, 6

2, 43, 5

5

1. Press MENU to open the menu.

The previous menu screen opens if menu operations have already been performed.

2. Press + or to select a menu group.

3. Press g to enter the menu item hierarchy.

Then select an item to be adjusted by pressing the h or g button.

4. Select or change the parameter by pressing + or .

MENU

Remote control

or

Control panel

MENU

Remote control

or

Control panel

Remote control

or

Control panel

Remote control

or

Control panel

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg hg hg hg hg

hg hg hg hg

hg hg hg

hg hg

hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg hg

Move Menu Window

Image

Black Level

Off L ML MH H

A B C D E

Memory 1 VIDEO

0

White Level 0

Gamma Trim

Hue 0

Saturation 100

Color Temp.

Sharpness Type

Sharpness Gain

Level adjustment

Iris

Color Balance

16

Signal Initial Setup

6000K +0.000uv

Standard

Standard Cinema

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg hg hg hg hg

hg hg hg hg

hg hg hg

hg hg

hg

hg hg

hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg hg

Memory 1 VIDEO

Setup

Location

Keystone 0

Remote Control Sensor

Remote Control ID

Lens Adjustment Lock

Economy Mode

Off On

White Boost Off On

Off On

Front / Table

Front & Rear

ID 1

Move Menu Window

Image Signal Initial

MonotoneMenu Color

Off On

Trigger Out

Baud Rate 125200bps

LAMP

Message

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg hg hg hg hg

hg hg hg hg

hg hg hg

hg hg

hg

hg hg

hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg hg

Memory 1 VIDEO

Setup

Location

Keystone 0

Remote Control Sensor

Remote Control ID

Lens Adjustment Lock

Economy Mode

Off On

Off On

Front / Table

Front & Rear

ID 1

MonotoneMenu Color

Move Menu Window

Image Signal Initial

Off On

Trigger Out

Baud Rate 125200bps

LAMP

Message

White Boost Off On

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg hg hg hg hg

hg hg hg hg

hg hg hg

hg hg

hg

hg hg

hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg hg

Memory 1 VIDEO

Setup

Location

Keystone 0

Remote Control Sensor

Remote Control ID

Lens Adjustment Lock

Economy Mode

Off On

Off On

Front / Table

Front & Rear

ID 1

MonotoneMenu Color

Move Menu Window

Image Signal Initial

Off On

Trigger Out

Baud Rate 125200bps

LAMP

Message

White Boost Off On

E-24

Some items are adjusted by increasing or decreasing the value on the scale, and others by selecting a number or a word.

Press the RESET button to reset the parameter to the factory setting. (Items without a factory setting cannot be reset.)

5. Press h or g to move the cursor to the next item.

To set a menu item in another menu group, press the ESCAPE or h button to return to the presently selected menu group, and follow steps 24 described previously to continue with menu setting.

6. Press MENU to close the menu when you have completed any changes.

Menu operation

Operation group A: Press the + or button to open the submenu. Select the desired parameter using the h or g buttons (h, g, +, or buttons for COLOR TEMP.), then press the ESCAPE button to close the submenu. *SIGNAL STATUS is a display-only massege which does not alter any parameters.

Operation group B: Press the + or button to open the submenu. Select the desired parameter using the h or g buttons, and press the button to confirm your setting. Press the ESCAPE button to close the submenu.

Operation group C: Press the + or button to open the submenu. Select the desired parameter using the h or g buttons and then use the + or buttons to change the parameters. It is not necessary to confirm the new setting.

Operation group D: Press the + or button to open the submenu. This submenu is in the form of messages. Follow the on- screen directions to adjust settings. The submenu for this group is explained on pages 26 and 27.

EXCEPTION Some submenu items have further submenus attached to them. These items have displayed on the right. Press the button to enter the detail menu, and select an appropriate setting using the cursor keys.

Remote control

or

Control panel

MENUMENU

Remote control

or

Control panel

Submenus Following is a list of the menu items that have a submenu. Submenu operation varies according to the menu item selected. Follow the steps of the applicable submenu operation group.

Menu items with a submenu

Submenu operation group

A

C

C

A

A*

B

B

B

B

B

B

A

D

D

A

B

B

A

A

A

Menu group

IMAGE

SIGNAL

INITIAL

SETUP

Menu item

COLOR TEMP.

COLOR BALANCE

LEVEL ADJUSTMENT

DISPLAY ASPECT

SIGNAL STATUS

COLOR SYSTEM

INPUT A SIGNAL

INPUT A SYNC TYPE

INPUT B SIGNAL

INPUT B SYNC TYPE

DVI SIGNAL

DISPLAY LANGUAGE

LAMP RUNNING TIME

RESET

LOCATION

REMOTE CONTROL SENSOR

REMOTE CONTROL ID

MENU COLOR

TRIGGER OUT

BAUD RATE

Gamma Trim A B C D E

Black Level

E-25

M E

N U

E n

g lish

3. Select the submenu parameter by pressing h or g.

Press the RESET button to reset the parameter to the factory setting. (Items without a factory setting cannot be reset.)

The following step is necessary to set COLOR SYSTEM, INPUT A SIGNAL, INPUT B SIGNAL, DVI SIGNAL and REMOTE CONTROL SENSOR in operation group B.

[Operation group B only] Press when setting is complete. This will confirm the new setting close the submenu. Settings for the above items will not be changed if not confirmed by the button.

To reset the parameter to the factory setting, press the RESET button when the submenu has been opened.

4. Press MENU to close the menu.

Press the ESCAPE or button to return to the previous screen and continue adjusting settings.

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg hg hg hg hg

hg hg hg hg

hg hg hg

hg hg

hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg hg

hg

MEMORY 1 VIDEOESCAPE: Return

Normal

Squeeze

Move Menu Window

Image

Display Aspect

Initial Setup

Auto

Signal

Smart Zoom

Zoom

Subtitle Zoom

Throug

Through Squeeze

Menu operation

Basic submenu operation

[Operation groups A and B]

1. Select the menu item to be adjusted by following steps 13 in Basic menu operation.

The submenu mark appears on the right side of the item.

2. Press + or to open the submenu.

Remote control

or

Control panel

Remote control

or

Control panel

Remote control

or

Control panel

MENUMENU

Remote control

or

Control panel

Move Menu Window

Image

Display Aspect

Memory 1 VIDEO

3D Y/C Separation

Noise Reduction

Video Type

Progressive Mode

Color Space Conversion

+: Enter

Initial Setup

Setup Level (SDTV)

Signal Status

Off On

DVD VCR

Auto

VideoAuto

0% 7.5%

Setup Level (HDTV) 0% 7.5%

1 2 3

Auto SDTV HDTV

Off

Signal

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg hg hg hg hg

hg hg hg hg

hg hg hg

hg hg

hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg hg

hg

MEMORY 1 VIDEOESCAPE: Return

Normal

Squeeze

Move Menu Window

Image

Display Aspect

Initial Setup

Auto

Signal

Smart Zoom

Zoom

Subtitle Zoom

Throug

Through Squeeze

E-26

Submenu operation COLOR BALANCE

[Operation group C]

1. Follow steps 13 in Basic menu operation to select the menu item COLOR BALANCE in menu group .

The submenu mark appears on the right side of the item.

2. To set RGBYCM parameters, select RGBYCM with the g button, and press the + button or to enter the submenu.

3. Select the submenu item by pressing h or g.

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg hg hg hg hg

hg hg hg hg

hg hg hg

hg hg

hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg hg

Move Menu Window

Image

Black Level

Off L ML MH H

A B C D E

Memory 1 VIDEO

0

White Level 0

Gamma Trim

Hue 0

Saturation 100

Color Temp.

Sharpness Type

Sharpness Gain

Level adjustment

Color Balance

16

+: Enter

Signal Initial Setup

6000K +0.000uv

Standard

Iris Standard Cinema

Menu operation

4. Use h, g, +, and to set the gauge figures to your liking.

Press the RESET button to reset the parameter to the factory setting.

5. Press MENU to close the menu.

To continue adjusting settings, press the ESCAPE button to return to the previous screen. Pressing the button will not close the submenu.

Submenu operation resetting LAMP RUN- NING TIME

[Operation group D]

1. Select the menu item LAMP RUNNING TIME in the menu group INITIAL by following steps 13 in Basic menu operation.

The submenu mark appears on the right side of the item.

2. Press + or to open the confirmation message screen.

Move Menu Window

Image

Memory 1 VIDEO+: Enter

Signal Initial Setup

Color Balance Standard

RGB

RGBYCM

Move Menu Window

Image

Memory 1 VIDEOESCAPE: Return

Signal Initial Setup

R Color Coordinate

R Gain 0.96

x=0.640 y=0.330

G Color Coordinate

G Gain 0.69

x=0.300 y=0.600

B Color Coordinate

B Gain 0.43

x=0.150 y=0.060

Y Color Coordinate

Y Gain 0.95

x=0.428 y=0.499

C Color Coordinate

C Gain 0.68

x=0.226 y=0.332

M Color Coordinate

M Gain 1.00

x=0.336 y=0.163

Move Menu Window

Image

Memory 1 VIDEO

Signal Initial Setup

R Color Coordinate

R Gain 1.20

x=0.640 y=0.330

ESCAPE: Return

G Color Coordinate

G Gain 0.69

x=0.300 y=0.600

B Color Coordinate

B Gain 0.43

x=0.150 y=0.060

Y Color Coordinate

Y Gain 0.95

x=0.428 y=0.499

C Color Coordinate

C Gain 0.68

x=0.226 y=0.332

M Color Coordinate

M Gain 1.00

x=0.336 y=0.163

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg hg hg hg hg

hg hg hg hg

hg hg hg

hg hg

hg

hg hg

hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg hg

Color Sytem

Memory 1 VIDEO

INPUT A Signal

INPUT A Sync Type

INPUT B Signal

INPUT B Sync Type

Auto Power Off

+: Enter

Auto Input Search

Display Language

Reset

Auto

Component

Auto

RGB PC

Auto

RGB PCDVI Signal

English

Lamp Running Time 0 Hour

OnOff

Off On

Setup

Move Menu Window

Image Signal Initial

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg hg hg hg hg

hg hg hg hg

hg hg hg

hg hg

hg

hg hg

hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg hg

Press " " to reset lamp running time.

No

Yes

Memory 1 VIDEO: Fix

Setup

Move Menu Window

Image Signal Initial

Lamp Running Time 0 Hour

E-27

M E

N U

E n

g lish

3. Press h or g to select the submenu item to reset.

4. Press + or to open the confirmation message screen.

5. Press to reset the parameter to its factory default setting.

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg hg hg hg hg

hg hg hg hg

hg hg hg

hg hg

hg

hg hg

hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg hg

MEMORY 1 VIDEO+: Enter

Reset

All Settings

All Memories

Current Memory

Setup

Move Menu Window

Image Signal Initial

Menu operation

3. Select YES with h or g, and then press .

LAMP RUNNING TIME will reset to 0 hour.

4. Press the MENU button to close the menu.

Submenu operationRESET

[Operation group D]

1. Follow steps 13 in Basic menu operations to select menu item RESET in menu group .

The submenu mark appears on the right side of the item.

2. Press + or to open the submenu.

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg hg hg hg hg

hg hg hg hg

hg hg hg

hg hg

hg

hg hg

hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg hg

No

Yes

Memory 1 VIDEO: Fix

Setup

Move Menu Window

Image Signal Initial

Lamp Running Time 0 Hour

Press " " to reset lamp running time.

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg hg hg hg hg

hg hg hg hg

hg hg hg

hg hg

hg

hg hg

hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg hg

Color Sytem

Memory 1 VIDEO

INPUT A Signal

INPUT A Sync Type

INPUT B Signal

INPUT B Sync Type

Auto Power Off

+: Enter

Auto Input Search

Display Language

Reset

Auto

Component

Auto

RGB PC

Auto

English

Lamp Running Time 0 Hour

OnOff

Off On

Setup

Move Menu Window

Image Signal Initial

RGB PCDVI Signal

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg hg hg hg hg

hg hg hg hg

hg hg hg

hg hg

hg

hg hg

hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg hg

Memory 1 VIDEO+: Enter

Reset

All Settings

All Memories

Current Memory

Setup

Move Menu Window

Image Signal Initial

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg hg hg hg hg

hg hg hg hg

hg hg hg

hg hg

hg

hg hg

hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg hg

Memory 1 VIDEOESCAPE: Return

Setup

Move Menu Window

Image Signal Initial

Press " " to reset all memories.

E-28

Changing the menu location

1. Press ESCAPE or h to return the cursor to the menu group.

2. Press h to enter the MOVE MENU WINDOW.

3. Press h, g, +, or to change the display location.

4. Press ESCAPE to return to the menu after setting the location.

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg hg hg hg hg

hg hg hg hg

hg hg hg

hg hg

hg

hg hg

hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg hg

Memory 1 VIDEO

Setup

Location

Keystone 0

Remote Control Sensor

Remote Control ID

Lens Adjustment Lock

Economy Mode

Off On

White Boost Off On

Off On

Front / Table

Front & Rear

ID 1

Move Menu Window

Image Signal Initial

MonotoneMenu Color

Off On

Trigger Out

Baud Rate 125200bps

LAMP

Message

Menu operation

One-touch image menu

1. Press when the menu screen is not open.

Menu items appear one by one at the bottom of the screen. The display will disappear if no operation is performed within five seconds.

2. Press h or g to select a menu item to adjust.

3. Press + or to select the desired value.

Press the RESET button to reset the parameter to the factory setting.

4. Press ESCAPE to close the display.

Remote control

or

Control panel

ESCAPE

ESCAPE

Remote control

or

Control panel

Remote control

or

Control panel

Remote control

or

Control panel

ESCAPE

ESCAPE

ESCAPE

Remote control

or

Control panel

Black Level

Remote control

or

Control panel

Remote control

or

Control panel

L ML MH HSharpness Type Off

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg hg hg hg hg

hg hg hg hg

hg hg hg

hg hg

hg

hg hg

hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg hg

Memory 1 VIDEOESCAPE: Return

Setup

Move Menu Window

Image Signal Initial

ESCAPE

ESCAPE

Remote control

or

Control panel

Sharpness Type Off L ML MH H

E-29

M E

N U

E n

g lish

Memory function This unit has a memory function able to store six settings for projecting different types of input sources in the most appropriate manner. Select the setting that is most appropriate for your projection. Some settings may not be available depending on the type of input signal currently in use. Six settings have been preset, but each parameter can be changed and restored at will. The following lists the menu items that you can store in memory.

Selecting the memory setting number

Using the remote control Press the MEMORY button number with the desired setting. (MEMORY BUTTON 16)

Using the menu

1. Press MENU to open the menu.

2. Press g to enter the memory setting number at the bottom of the screen.

3. Press + to open the submenu.

4. Press h or g to select the number of the desired memory setting number.

5. Press ESCAPE to close the submenu.

4 5 6

1 2 3

MEMORY

MENU

IMAGE

BLCK LEVEL (BRIGNTNESS) WHITE LEVEL (CONTRAST) GAMMA TRIM SATURATION HUE COLOR TEMP. SHARPNESS TYPE SHARPNESS GAIN COLOR BALANCE LEVEL ADJUSTMENT IRIS

SIGNAL

3D Y/C SEPARATION VIDEO TYPE PROGRESSIVE MODE COLOR SPACE CONVERSION SETUP LEVEL SIGNAL LEVEL

ESCAPE

Move Menu Window

Image

Memory 1 VIDEO+: Enter

Initial SetupSignal

Display Aspect

3D Y/C Separation

Noise Reduction

Video Type

Progressive Mode

Color Space Conversion

Setup Level (SDTV)

Signal Status

Off On

DVD VCR

Auto

VideoAuto

0% 7.5%

Setup Level (HDTV) 0% 7.5%

1 2 3

Auto SDTV HDTV

Off

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg hg hg hg hg

hg hg hg hg

hg hg hg

hg hg

hg

hg hg

hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg hg

6

Memory 5

Memory 4

Memory 3

Memory 2

Memory 1

Move Menu Window

Image

Memory 6 VIDEOESCAPE: Return

Initial SetupSignal

E-30

Memory function

To reset all parameters in all six memory settings Follow the directions in Submenu operationRESET on page 27 to select ALL MEMORIES on the submenu. Press the + or buttons to open the confirmation message screen. Press the button to reset to factory default settings.

Resetting to the factory default settings

For one parameter Follow steps 13 in Basic menu operation on page 23 to select the parameter to reset. Press the RESET button on the remote control to return the parameter to its factory default setting. (Items without a factory default cannot be reset.)

To reset all parameters for the currently selected memory number Follow the directions in Submenu operationRESET on page 27 to select CURRENT MEMORY on the submenu. Press the + or buttons to open the confirmation message screen. Press the

button to reset the selected memory area to its factory default settings.

Remote control

or

Control panel

Remote control

or

Control panel

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg hg hg hg hg

hg hg hg hg

hg hg hg

hg hg

hg

hg hg

hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg hg

Memory 1 VIDEOESCAPE: Return

Setup

Move Menu Window

Image Signal Initial

Press " " to reset current memory.

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg

hg hg hg hg hg

hg hg hg hg

hg hg hg

hg hg

hg

hg hg

hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg

hg hg hg

Memory 1 VIDEOESCAPE: Return

Setup

Move Menu Window

Image Signal Initial

Press " " to reset all memories.

E-31

E n

g lish

A D

D IT

IO N

A L

IN F

O R

M A

T IO

N

AAAAA

Glossary The following is a list of key words and their explanations used in the use of projectors and image signals. Please refer to it when using the DPX-1000.

DLP technology This stands for Digital Light Processing. DLP uses the DMDTM

chip, developed by Texas Instruments.

DCDi function This is an abbreviation of Directional Correlational Deinterlacing, a high quality image circuitry developed by the Faroudja company. It uses edge cutting techniques to remove jagged edges from images during Interlace Progressive conversion, allowing smooth, natural image reproduction.

Component video signal Component video signal is sent with independent luminance and color signals. It gives a higher image quality than ordinary composite video signal because it bypasses mixing and separating circuits. Component video signal consists of three lines, the luminance signal (Y) and two color difference signals (PB/CB, PR/CR).

S video signal S stands for Separate. This signal is sent with separated luminance (Y) and color (C) signals. Use a 4-pin mini DIN connector and cable for connection.

Composite video signal This is the most common type of video signal. The luminance signal and color signal are sent combined in one line. Mixing and separating processes are necessary on both the send and receive sides. A pin cable is used for connection.

RGB signal An RGB signal transmits color information by using a numeric representation of the primary colors of red, green and blue separately. When the signal is received, it can be expressed in various colors by adding and mixing colors. This type of signal is widely used for sending and receiving color images between computers. Horizontal and vertical sync signals are also necessary.

HDTV This is an abbreviation of High-Definition Television, a term used to define systems that satisfy the following conditions:

A vertical resolution of 720p, or 1080i (p stands for progressive scans, i stands for interlace scans).

An image aspect ratio of 16:9

SDTV An abbreviation of Standard Definition Television, used to define normal television broadcasts which do not meet the standards of HDTV.

Additional information

D connector This connector is designed for the Japanese D format only. It is used for sending and receiving the image signal between the latest type of A/V components. This connector can receive the component signal by using a D connector cable. There are five levels (D1D5) of performance characteristics. This unit is compatible with D1, 2, 3, and 4.

DVI connector A digital RGB/Component signal is sent differentially from a computer or A/V equipment to this connector. A 24-pin connector and cable are used.

Standby The state in which the circuit to receive infrared-signals from the remote control is activated but other main circuits are turned off. A small amount of power is consumed in this state.

Test pattern Test patterns are stored in this unit for use in adjusting the position and focus of the projected image on the screen.

Interlace The most common type of scanning in use in televisions. It divides an image into two fields for scanning, and uses even and odd numbered lines of those fields to build an image (frame).

Progressive This displays all the scanning lines of the entire frame at one time. It greatly reduces the flicker that is more noticeable on a larger screen to create a sharp and smooth image. This unit projects using progressive scanning.

3-2 Pulldown detection style IP conversion A function for directly converting interlace signal into sixty frame progressive signal used when receiving 60 field interlace signal from an image source recorded with the same 24 frames as movie film. This allows DVD and other materiel recorded with 24 frames to be projected on large screens as a natural, precise image with no loss of quality, comparable to a movie film.

SYNC Computers output signals with a given regular frequency, which the projector must be synchronized to in order to produce a good quality image. Failure to match the phase of the signal will result in flickering, fading, and distortion of the image.

TRACKING Computers output signals with a given regular frequency, which the projector must be synchronized to in order to produce a good quality image. Failure to match signal frequencies will result in vertical striping in the image.

DLP and DMD are trademarks of Texas Instruments.

is a trademark of Faroudja, a division of Genesis Microchip Inc.

E-32

HDCP High-bandwidth Digital Content Protection system. HDCP is designed to protect the video transmission between a DVI transmitter and a display device.

Aspect This refers to the length-to-width ratio of an image.

Ceiling mount bracket This is the mounting hardware used to hand this unit from the ceiling. Two types of bracket are available, for high and low ceilings. Ceiling mount brackets are sold separately.

Key stone If the unit is used at an angle to the screen the projected image will be distorted in a trapezoid fashion. Keystone is used to electronically correct this distortion.

Letter box This is a method used to convert the content of a film in landscape orientation to a 4:3 signal. It is possible to watch a landscape image without trimming by adding a black bar to the top and bottom of the screen, however this sacrifices vertical resolution to some extent.

Squeeze This method compresses a film image horizontally to an aspect ratio of 4:3 when recording on a video medium. The squeezed image must pass through a de-squeezing circuit in order to be projected in its original form.

Smart Zoom Smart zoom expands the left and right sides of a 4:3 image without altering the center, when it is necessary to project a 4:3 image to a wide screen format. This creates some distortion at both edges.

Vista size A standard film size. The aspect ratio is 1.85:1 in North America and 1.66:1 in Europe.

Cinema scope size The widest film format in 70mm film. The aspect ratio is 2.35:1.

Color spacing This refers to the conversion of YUV color separated signal to RGB signal. There are two formats for this, SDTV BT.601 and HDTV BT.709. This unit can switch between them as required.

Additional information

E-33

E n

g lish

A D

D IT

IO N

A L

IN F

O R

M A

T IO

N

Additional information

Projectable signals The following charts show the types and formats of the signals that can be projected by this unit. Any signals not listed below may not be properly projected.

1. TV format 1 ------ Composite or S video signals sent to the VIDEO or S-VIDEO inputs

2. TV format 2 ------- Component or RGB TV signals sent to the INPUT A, B and DVI, or component signals sent to the D4, DVI input connector

Type of signal

NTSC

PAL

SECAM

PAL60

NTSC4.43

PAL-M

PAL-N

V active (lines)

480

576

576

480

576

480

576

f (V)

(Hz) 59.94

50.00

50.00

59.94

59.94

59.94

50.00

fsc (MHz)

3.58

4.43

4.406, 4.25

4.43

4.43

3.58

3.58

Color system

NTSC

PAL

SECAM

PAL

NTSC

PAL

PAL

Type of signal

480i*

576i*

480p

576p

720p/50Hz

720p/60Hz

1035i*

1080i/50Hz

1080i/60Hz

H active (pixels)

720

720

720

720

1280

1280

1920

1920

1920

V active (lines)

483

576

480

576

720

720

1035

1080

1080

f (H)

(kHz) 15.734

15.625

31.469

31.250

37.500

45.000

33.750

28.125

33.716

f (V)

(Hz) 59.940

50.000

59.940

50.000

50.000

59.940

60.000

50.000

59.940

f (V)

(Hz) 59.940

72.809

75.000

85.008

56.250

60.317

72.188

75.000

85.061

60.004

66.666

Type of signal

VGA/60Hz

VGA/72Hz

VGA/75Hz

VGA/85Hz

SVGA/56Hz

SVGA/60Hz

SVGA/72Hz

SVGA/75Hz

SVGA/85Hz

XGA/60Hz

Mac13

H active (pixels)

640

640

640

640

800

800

800

800

800

1024

640

V active (lines)

480

480

480

480

600

600

600

600

600

768

480

f (H)

(kHz) 31.469

37.861

37.500

43.269

35.156

37.879

48.077

46.875

53.674

48.363

35.000

VESA

Apple

DVI digital component format supports YCBCR 4:4:4 (8 bit x 3) only.

* This unit does not support these signal types when using a DVI connection.

3. PC format 1 ------ Analog RGB PC signals sent to the INPUT A or B inputs

VESA is trademark of Video Electronics Standards Association.

Macintosh is a trademark of Apple Computer, Inc.

4. PC format 2 ------ Digital RGB signal input sent to the DVI input terminal Depending on the computer you are using, projection may not be possible in this mode.

H active (pixels)

640

800

1024

1280

V active (lines)

480

600

768

720

f (H)

(kHz) 31.469

37.879

48.363

45.000

f (V)

(Hz) 59.940

60.317

60.004

59.940

VESA

Type of signal

VGA/60Hz

SVGA/60Hz

XGA/60Hz

1280x720/60Hz

E-34

Additional information

Message

No Signal

INPUT A (Component) (Example)

Out Of Range

Unknown Format

Auto Sync...

Memory 16

The lamp needs to be replaced. Please replace the lamp you are currently using with a new one.

Press again for standby.

Squeeze (Example)

Lens Adjustment is locked.

Message display

Condition

The unit is not receiving or detecting any signal at the selected input source. This message is displayed together with the name of the input source selected with the INPUT button.

The input name selected by the INPUT button is displayed. It will turn off 1 minute after the signal has been input.

The unit is not able to decode the PC signal currently being input.

The unit is not able to decode the video signal currently being input.

The unit is setting itself to the most appropriate configuration for the RGB signal currently being received.

The memory setting number is displayed for 2 seconds.

This message is displayed when the power switch is turned on if the lamp running time exceeds 2000 hours. Press the ESCAPE key to remove the message.

Press the STANDBY/ON button once more to place the unit in standby mode.

The name of the display aspect mode selected with the ASPECT button is displayed for 2 seconds.

Displayed when the LENS ADJUSTMENT LOCK is set to ON. This message will display for 2 seconds if you press the V.POS, ZOOM, or FOCUS buttons when the LENS ADJUSTMENT LOCK is set to ON.

E-35

E n

g lish

A D

D IT

IO N

A L

IN F

O R

M A

T IO

N

Maintenance

Regular care Be sure to disconnect the power cable prior to doing any mainte- nance.

Wipe with a soft cloth. Use a damp cloth with a mild detergent and then wipe with a dry cloth again if the unit is heavily soiled. Do not use strong solvents such as thinner or alcohol as they may damage the case of this unit.

Use commercially available blowers or lens tissue to remove any dirt from the lens.

If dust is allowed to accumulate on the ventilation port filter, the internal temperature of the unit will rise which may cause damage to the unit. Clean the filter approximately once every 200 hours. Remove the power cable from the power outlet, and remove dust from the filter with a vacuum cleaner.

Be sure to vacuum the filter with the unit on its side, in order to prevent dust from entering the filter itself.

Filter replacement Replace the filter when it becomes difficult to remove dust from it.

1. Turn off the power and disconnect the power cable from this unit.

2. Carefully place the unit upside down on a soft cloth to prevent scratching.

3. Press the filter hook on the underside of the main unit to remove the filter.

4. Attach the new filter firmly. The lamp will not light if the filter is not attached correctly.

Important

Contact a Yamaha electronic goods service point if you require replacement filters.

E-36

Maintenance

Replacing the lamp cartridge

Important

Be sure to use the replacement lamp cartridge PJL 327. Other lamp cartridges are not suitable for use in this unit.

The lamp used as a light source in this unit is a consumable and will gradually lose its brightness during the course of use. It is advisable to replace the lamp when running time has exceeded 2000 hours.

You can view the current lamp running time in 3 on the menu. The LAMP warning indicator will blink when running time exceeds 2000 hours. (See page 15.) There will also be a message displayed on the screen. In this case, follow the instructions below to replace the lamp cartridge. Be sure to use the replacement lamp cartridge PJL 327. Other lamp cartridges are not suitable for use in this unit. Consult the store where this unit was bought for details on replacement lamp cartridges.

Important

Before starting to replace the lamp cartridge, turn off the power, disconnect the power cable after the fan has com- pletely stopped, and wait at least one hour for the lamp to cool down.

Do not remove any other screws than those specified in the following steps.

1. Loosen the lamp cover screws.

2. Remove the lamp cover.

Important

Take care not to drop the lamp or cover when replacing a lamp in a ceiling mounted unit.

Lamp cover screws

3. Loosen the screws of the lamp cartridge.

4. Grip the handle and pull the lamp cartridge to remove it.

5. Insert the new lamp cartridge by reversing the above steps, and tighten the screws to fix it into place.

6. Replace the lamp cover and secure it with the screws.

The lamp will not turn on if the cover is not securely fastened. Take care to attach it firmly in place.

7. Connect the unit to the power outlet, turn the unit on, and reset LAMP RUNNING TIME on the 3 section in the menu. (See page 20.)

E-37

E n

g lish

A D

D IT

IO N

A L

IN F

O R

M A

T IO

N

Troubleshooting

Problem

This unit does not turn on.

No picture

Image is unstable.

Picture is blurred.

The image becomes cloudy.

Cannot adjust focus or zoom, or the vertical position of the lens.

Remote control does not work correctly.

COVER warning indicator lights up.

LAMP warning indicator lights up or blinks.

TEMP warning indicator lights up.

FAN warning indicator lights up.

Remedy

Plug the power cable in firmly.

In order to protect the lamp, the unit will not turn on again for 2 minutes after the power is turned off.

Correctly attach the filter cover.

Correctly attach the lamp cover.

Remove the lens cover.

Check the connections.

Select the correct input signal with the INPUT button.

Press the AUTO button.

Use the menu to adjust the signal setting to suit the input setting.

Press the HIDE button again to cancel the HIDE function.

Set the computer to display on the external monitor. (Refer to the computer operating instructions.)

Correctly connect the cables to the appropriate connectors.

Press the FOCUS button, and adjust the focus.

Adjust the projection angle and direction, and the height of this unit.

Switch the unit power off until the condensation disappears.

Set LENS ADJUSTMENT LOCK to OFF.

Replace both batteries with new ones.

Select an appropriate remote control sensor from the menu.

Turn off this remote sensor.

Tightly attach the filter cover.

Tightly attach the lamp cover.

Replace the lamp with a new one.

Replace the lamp with a new one.

Check that the ventilation slots are not covered.

Contact the store where this unit was purchased.

Cause

The power cable is not plugged in.

You attempted to turn on this unit immediately after turning it off.

The filter cover is not correctly attached.

The lamp cover is not correctly attached.

The lens cover has not been removed.

This unit is not correctly connected to the other components.

The input signal has not been correctly selected.

The picture is turned off.

The computer is not set to display on the external monitor.

The connection cables are not correctly attached to the connectors.

The lens is not correctly focused.

The screen and the main unit are not facing each other directly.

There is condensation on the unit.

LENS ADJUSTMENT LOCK in the menu is set to ON.

The batteries are exhausted.

The remote control sensor is not set correctly.

There is a fluorescent lamp near the remote control sensor being used.

The filter cover is not correctly attached.

The lamp cover is not correctly attached.

Lamp running time has exceeded 2000 hours.

The lamp has burned out.

The temperature inside this unit is extremely high.

The fan is broken.

E-38

Specifications

Specifications

Optical

Projection mode .......................... DLP (Digital Light Processing) Images of 1280 x 720 pixels, 0.8 inch

Lens .................................................. f=24.4 to 39 mm F=2.4 to 3.1 Electronic zoom (x 1.6)

Electronic focus

Lamp ..................................................................... 270 W SHP lamp

Image size ............................................................... 60 to 200 inches Projection distance 1.8 to 6.05 m (707/8 to 2361/5)

(Wide image, 16:9 screen)

Brightness ........................................ 800 ANSI lm (Standard mode) 500 ANSI lm (Cinema mode)

Contrast ...................................................... 2700:1 (Standard mode) 1500:1 (Cinema mode)

Electrical

Color mode .................................. NTSC, PAL, SECAM, NTSC4.43, PAL-M, PAL-N, PAL60

Scanning frequency .......... H:15 to 54 kHz/V; 50 to 85 Hz (Analog) 50 to 60 Hz (Digital)

Input

VIDEO Composite signal 1Vp-p/75, negative sync.

S VIDEO S video signal Y: 1Vp-p/75, negative sync. C: 0.286 or 0.3Vp-p/75

D4 VIDEO Component signal Y with sync.: 1Vp-p/75, negative sync. (480i, 576i, 480p, 576p) Y with sync.: 1Vp-p/75, 3 values sync. (1035i, 1080i, 720p) PB, PR: 0.7Vp-p/75

INPUT A/INPUT B Component signal

Y with sync.: 1Vp-p/75, negative sync. (480i, 576i, 480p, 576p) Y with sync.: 1Vp-p/75, 3 values sync. (1035i, 1080i, 720p) PB, PR: 0.7Vp-p/75

RGB signal G with sync.: 1Vp-p/75, negative sync. (480i, 576i, 480p, 576p) G with sync.: 1Vp-p/75, 3 values sync. (1035i, 1080i, 720p) G: 0.7Vp-p/75 (when using HD/VD or SYNC) B, R: 0.7Vp-p/75 HD, VD: 1 to 5 Vp-p/2.2 k, positive and negative sync. SYNC: 2Vp-p/2.2k, negative sync. (480i, 576i) SYNC: 1 to 5 Vp-p/2.2k, positive and negative sync. (480i, 576i, 480p, 576p)

DVI Digital RGB/Component signal

Controls

Remote ........................................................ RS-232C (D-Sub 9 pin)

Trigger ................ +12 V/Maximum 200 mA when the power is on; 0 V when the power is off (mini jack)

Remote control sensor

Wireless remote control ......................... one in front and one at rear

Wired remote control .................................................. one input jack one output jack

General

Usable temperature range .............................................. 5C to 35C

Usable humidity range ................................................... 30% to 85% (There should be no condensation.)

Power supply ................... AC 100 to 120 V/220 to 240 V, 50/60 Hz

Power consumption ................................................................ 365 W Standby mode ..................................................................... 0.1 W

Noise Level ................................................... 30 db (Standard mode) 28 db (Economy mode)

Dimension ............................. 495 (W) x 189.5 (H) x 465.4 (D) mm 19-1/2 (W) x 7-1/2 (H) x 18-5/16 (D) inch

Weight .............................................................. 13.8 kg (30 lbs 7 oz)

* Specifications are subject to change without notice.

This unit may interfere with reception if placed in close proximity to a radio or television receiver. Follow the instructions in this manual to install the unit correctly.

E-39

E n

g lish

A D

D IT

IO N

A L

IN F

O R

M A

T IO

N

S TA

N D

B Y

/O N

S ET

TI N

G

LA M

P C O

V ER

TE M

P FA

N

PA TT

ER N

E S C A

P E

M E N

U

IN P U

T

D IG

IT A

L C

IN E M

A P

R O

J E C T O

R D

P X -1

0 0

0

A S P E C T

D V I

IN P U

T B

R G

B / Y P

BP R/

Y C

BC R

D 4

V ID

EO G

/ Y

B / P

B/ C

B R

/ P

R/ C

R

IN P U

T A

H D

/ S Y N

C V D

O U

T IN

R EM

O TE

R S -2

3 2

C

S -V

ID EO

V ID

EO

TR IG

G ER

O U

T

465.4 18"-5/16

124.6 4"-7/8

119.1 4"-3/5

12 4

4" -7

/8

297.4 11"-3/4

132.1 5"-3/16

49 5

19 "-

1/ 2

36 0

14 "-

3/ 16

18 9.

5 7"

-1 /2

23 7.

5 9"

-3 /8

10 3/ 8

(2 57

.5 10

"- 1/

8)

Specifications

Dimensional drawing

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSWORTH ROAD WATFORD, HERTS WD1 7JS, ENGLAND YAMAHA SCANDINAVIA A.B. J A WETTERGRENS GATA 1, BOX 30053, 400 43 VSTRA FRLUNDA, SWEDEN YAMAHA MUSIC AUSTRALIA PTY, LTD.

Manualsnet FAQs

If you want to find out how the DPX-1000 Yamaha works, you can view and download the Yamaha DPX-1000 Projector Owner's Manual on the Manualsnet website.

Yes, we have the Owner's Manual for Yamaha DPX-1000 as well as other Yamaha manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Owner's Manual should include all the details that are needed to use a Yamaha DPX-1000. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Yamaha DPX-1000 Projector Owner's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Yamaha DPX-1000 Projector Owner's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Yamaha DPX-1000 Projector Owner's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Yamaha DPX-1000 Projector Owner's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Yamaha DPX-1000 Projector Owner's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.