Summary of Content for Yamaha PWK-150 Mount Installation Instructions PDF
PWK 150 WALL MOUNTING UNIT
Installationsanleitung Vor der Installation lesen Site bitte diese Anleitung sorgfaltig durch. Diese Anleitung zum spateren Nachschlagen aufbewahren.
Instruzioni per Iinstallazione Prima di iniziare a montare questi accessori, siete pregati di leggere interamente le presenti istruzioni. Siete inoltre pregati di conservare questo libro per future consultazioni.
Manuel dinstallation Avant dessayer dassembler ces accessories, vauillez lire ces instructions compltement. Veuillez garder ce manuel pour une rfrence future.
Instrucciones de instalacin Antes de instalar estos accesorios, lea cuidadosamente estas instrucciones. Guarde estas instrucciones para futuras referencias.
Installation Instructions Before attempting to assemble these accessories, please read these instructions completely. Please retain this book for future reference.
Before installing the wall mounting unit, please read these instructions and the plasma display operation manual
carefully to make sure installation is carried out correctly.
After installation, please hand these instructions to the customer and ask him to carefully read them and keep
them for future reference. (The instructions may be needed again when moving or carrying out maintenance.)
Precautions with regard to setting up WARNING
Installation work should only be carried out by a qualified technician. If the wall mounting unit is installed incorrectly, the display may fall down and personal injury
Make sure that all safety factors regarding strength of installation are observed. If the installation strength is insufficient, the display may fall down and personal injury may
Do not install in places which are unable to bear loads. If the strength of the installation surface is insufficient, the display may fall down and personal
injury may result.
Do not install in places which are subject to humidity, dust, oil fumes, water vapour or excessive heat. These can have adverse effects on wide plasma display operation, and fire or electric shocks
Do not install the wide plasma display face up, sideways or upside down. Doing so may cause heat to build up inside the display, and fire may result.
Two people are required to install and remove the display. If two people are not present, the display may be dropped, and personal injury may result.
Maintain a space of at least 10 cm (3 15/16 inches) at the top, bottom and sides of the display, and at least 1.9 cm (3/4 inches) at the rear of the display. The display has air outlet holes at the top and air intake holes at the bottom and rear. These
holes must not be covered, otherwise fire may result.
Points to note for installation The wall mounting unit is for use in installing the wide plasma display to a vertical wall for
viewing purposes. Do not use it for any type of installation other than vertical wall installation.
In order to ensure correct, problem-free operation of the wide plasma display, do not install the display in any of the following places.
Places which are next to sprinklers or sensors Places which are subject to vibration or shocks Places which are close to high-voltage wires or electric motors Places in direct contact with air from heaters
When installing this wall mounting unit, use a fixing method appropriate to the type of wall.
Use an M6 bolt (sold separately) appropriate for the type of wall material (wood, steel frame, concrete, etc.) the bracket is to be mounted on.
Insert the power cord plug for the wide plasma display into a wall outlet which is close and easily accessible.
Provide adequate ventilation so that the temperature around the display does not rise above 40C (104 F). If there is insufficient movement of the air inside display, heat may build up inside the display, and fire may result.
Wall mounting unit.............................................................1 Allen key (accessory) ......1
M5 screw .........................2
Toothed pan washer
Pan head bolt with
hex socket (M8-45) .........4
The wall mounting unit weighs approximately 6 kg (13.23 lbs.), and the wide plasma display unit weights
approximately 43 kg (94.8 lbs.).
While referring to the wall mounting unit installation dimensions in the diagram below, check the strength of the
wall in six installation locations, and add reinforcing if any of these locations are not strong enough.
The wall mounting unit has installation holes provided in 24 locations. If the wall material will not allow sufficient strength to be obtained from using six installation holes, use some of the spare holes. However, depending on the construction material used at the place of installation, cracks may develop if the screws are inserted too close to each other.
N o t eNote
N o t eNote
Installation procedure First screw a bolt into the center-top hole. Use a level gauge to correct the alignment of the wall mounting unit, and then screw bolts into the remaining five holes. Provisionally tighten the fixing screws. If the screws are inserted more than 5 mm (13/64 inches), it will not be possible to install the wide plasma display in the correct position.
1. Check the strength of the installation location.
2. Install the wall mounting unit to the wall.
Fixing screw Fixing screw
Install the wall mounting unit so that the arrow shown on the wall mounting unit is pointing upwards. If it is necessary to embed bolts or nuts beforehand because the wall is made from concrete, use the wall
mounting unit itself to determine the correct installation hole positions, or use the dimension diagram to calculate the hole positions. Then embed the M6 bolts or nuts into the holes. Furthermore, when embedding the bolts, allow the bolts to protrude from the wall by 10 mm (13/32 inches) to 15 mm (19/32 inches).
930 (36 39/64)
450 (17 23/32)450 (17 23/32)
100 50 (1 31/32)
Used for routing wires behind a wall
Units : mm ( ) : inches
(2 5 /
(2 5 /
Wall installation holes (6 locations)
Use commercially-available M6 bolts which suit the wall materials for installation to the wall.
YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE YAMAHA ELECTRONICS (UK) LTD. YAMAHA HOUSE, 200 RICKMANSW
If you want to find out how the PWK-150 Yamaha works, you can view and download the Yamaha PWK-150 Mount Installation Instructions on the Manualsnet website.
Yes, we have the Installation Instructions for Yamaha PWK-150 as well as other Yamaha manuals. All you need to do is to use our search bar and find the user manual that you are looking for.
The Installation Instructions should include all the details that are needed to use a Yamaha PWK-150. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.
The best way to navigate the Yamaha PWK-150 Mount Installation Instructions is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.
This Yamaha PWK-150 Mount Installation Instructions consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.
You can download Yamaha PWK-150 Mount Installation Instructions free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.
To be able to print Yamaha PWK-150 Mount Installation Instructions, simply download the document to your computer. Once downloaded, open the PDF file and print the Yamaha PWK-150 Mount Installation Instructions as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.