Contents

Yamaha PDM-5520 Monitor User's Manual PDF

1 of 50
1 of 50

Summary of Content for Yamaha PDM-5520 Monitor User's Manual PDF

IMPORTANT SAFETY INSTRUCTIONS SAFETY POINTS YOU SHOULD KNOW ABOUT YOUR Yamaha High Definition Plasma Monitor Please read this section carefully to obtain a proper understanding of how to operate your Yamaha High Definition Plasma Monitor. And make sure you follow all of the warnings and instructions marked on this monitor.

CAUTION

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).

NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of a sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle, is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS MONITOR TO RAIN OR MOISTURE. THE MONITOR SHOULD NOT BE EXPOSED TO DRIPPING OR SPLASHING AND OBJECTS

FILLED WITH LIQUIDS, SUCH AS VASES, SHOULD NOT BE PLACED ON THE MONITOR.

NOTE: There are no user serviceable parts inside the monitor. Model and serial numbers are indicated on back side of the monitor.

CAUTION: Adjust only those controls that are covered in the instructions, as improper changes or modifications not expressly approved by YAMAHA could void the user's authority to operate the monitor.

POWER SOURCE

THIS MONITOR IS DESIGNED TO OPERATE ON 120 VOLTS 60Hz, ALTERNATING CURRENT. INSERT THE POWER CORD INTO A 120 VOLT 60Hz OUTLET.

TO PREVENT ELECTRIC SHOCK, DO NOT USE THE MONITOR'S (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE, OR OTHER OUTLET UNLESS THE BLADES AND GROUND TERMINAL CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

NEVER CONNECT THE MONITOR TO DIRECT CURRENT OR ANYTHING OTHER THAN THE SPECIFIED VOLTAGE.

CAUTION: Never remove the back cover of the monitor as this can expose you to very high voltages and other hazards. If the monitor does not operate properly, unplug the monitor and call your authorized dealer or service center.

For Canadian customers: To prevent electric shock, match wide blade of plug to wide slot and fully insert. This Class B digital apparatus complies with Canadian ICES-003.

READ ALL INSTRUCTIONS CAREFULLY. KEEP THIS USERS MANUAL FOR FUTURE REFERENCE.

For future reference, record the serial number of your monitor.

SERIAL NO. The serial number is located on the rear of the monitor.

RISK OF ELECTRIC SHOCK DO NOT OPEN

1

010_PDM-5520_U_E 12/13/04, 9:23 AM2

1

E N

G L

IS H

IMPORTANT SAFETY INSTRUCTIONS Read before operating equipment Follow all warnings and instructions marked on this monitor. 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with a dry cloth. 7. Do not block any ventilation openings. Install in accordance

with the manufacturer's instructions. 8. Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding- type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use the attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15. Monitors are designed to comply with the recommended safety standards for tilt and stability. Do not apply excessive pulling force to the front, or top, of the cabinet which could cause the product to overturn resulting in product damage and/or personal injury.

16. Follow instructions for wall, shelf or ceiling mounting as recommended by the manufacturer.

17. An outdoor antenna should not be located in the vicinity of overhead power lines or other electrical circuits.

18. If an outside antenna is connected to the receiver be sure the antenna system is grounded so as to provide some protection against voltage surges and built up static charges. Section 810 of the National Electric Code, ANSI/NFPA No. 70-1984, provides information with respect to proper grounding for the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding connectors, location of antenna-discharge unit, connection to grounding electrodes and requirements for the grounding electrode.

Note to the CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

ANTENNA LEAD IN WIRE

GROUND CLAMP

ELECTRIC SERVICE EQUIPMENT

NEC NATIONAL ELECTRICAL CODE

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

GROUNDING CONDUCTORS (NEC SECTION 810-21)

GROUNDING CONDUCTORS

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250 PART H)

Do not place any objects on the top of the monitor which may fall or cause a child to climb to retrieve the objects.

Disposal of this product may require specific instructions pertaining to your resident state. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance: www.eiae.org.

PREVENTION OF IMAGE RETENTION Continuous on-screen displays such as video games, stock market quotations, computer generated graphics, and other fixed (non-moving) patterns can cause permanent damage to the monitor.

PUBLIC VIEWING OF COPYRIGHTED MATERIAL Public viewing of programs broadcast by TV stations and cable companies, as well as programs from other sources, may require prior authorization from the broadcaster or owner of the video program material.

2

011_PDM-5520_U_E 12/13/04, 9:23 AM1

2

FCC (Federal Communications Commission) STATEMENT WARNING

COMPLIANCE INFORMATION STATEMENT

(DECLARATION OF CONFORMITY PROCEDURE) Responsible Party: Yamaha Electronics Corporation

Address: 6660 Orangethorpe Avenue Buena Park, CA90620

Telephone: 714-522-9105 Fax: 714-670-0108

Type of Equipment: High Definition Plasma Monitor Model Name: PDM-5520

This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received including interference that may cause undesired operation. See the user manual instructions if interference to radio reception is suspected.

FCC INFORMATION (for US customers)

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class B digital devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential environment will not result in harmful interference with other electronic devices.

This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in theusers manual, may cause interference harmful to the operation of other electronic devices.

Compliance with FCC regulations does not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit OFF and ON, please try to eliminate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by the interference.

Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to coaxial type cable.

If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Electronics Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA 90620.

The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.

2-1

011_PDM-5520_U_E 12/13/04, 9:23 AM2

3

E N

G L

IS H

Thank you very much for purchasing the Yamaha High Definition Plasma Monitor. Before using your monitor, please carefully read this manual so you will know how to operate the monitor properly. Keep this manual in a safe place. You will find it useful in the future.

Notes on lnstallation Work: This product is marketed assuming that it is installed by qualifed personnel with enough skill and competence. Always have an installation specialist or your dealer install and set up the product. YAMAHA cannot assume liabilities for damage caused by mistake in installation or mounting, misuse, modification or a natural disaster.

Note for Dealers: After installation, be sure to deliver this manual to the customer and explain to the customer how to handle the product.

Notes about This Manual The information in this manual is subject to change without

notice. While meticulous care has been taken in the preparation of this

manual, you are requested to notify your dealer or us should you have any comments, views or questions about our product.

Fully understand the prerequisites to using the product, such as hardware and software specifications and constraints, in using the product. We are not held liable for damages caused by improper handling of the product.

Reproduction of this manual in whole or in part without our prior written permission is prohibited.

The product names mentioned in this manual may be trademarks or registered trademarks of their respective owners.

USERS MANUAL

011_PDM-5520_U_E 12/13/04, 9:23 AM3

4

FEATURES Large-screen, high-definition plasma display panel The 55-inch color plasma display panel, with a resolution of 1366 (H) x 768 (V) pixels, creates a high-definition, large-screen (aspect ratio : 16:9) and low-profile flat display. Free from electromagnetic interferences from geomagnetic sources and ambient power lines, the panel produces high-quality display images free from color misconvergence and display distortion.

High Performance Digital Processor A wide range of personal computer signals can be handled, from 640 x 400, 640 x 480 VGA to 1600 x 1200 UXGA. (RGB Analog input)

Easy-to-use remote control and on screen display system The remote control included eases the work of setting display controls. Further, the on-screen display system, displays the status of signal reception and display control settings in an easy-to-view fashion.

TruBass TruBass, SRS and (O) symbol are trademarks of SRS Labs, Inc. TruBass technology is incorporated under license from SRS Labs, Inc.

Built in Video Unit (1) A Composite/S video terminal and two component terminals

have been added. A composite video output terminal is also provided as a monitoring output.

(2) A wide range of devices other than personal computers can also be connected.

(3) It is possible to swich the component terminal to RGB input from the Menu screen.

(4) A SCART terminal is also provided for the signal of the European standard. It operates as composite/S/RGB input terminal, or video output terminal.

Options

Ask your local retail dealer for further details on the following optional attachments. Pedestal

PDS-355

This Users Manual was printed before final product development. After printing, some product specifications may change due to operational upgrades and other reasons. In this case, the specifications of the product itself will take precedence over the specifications in this manual.

TRADEMARK ACKNOWLEDGEMENT VGA and XGA are registered trademarks of International Business Machines Corporation. APPLE and Macintosh are registered trademarks of Apple Computer, Inc. All brand or product names are trademarks or registered trademarks of their respective holders.

011_PDM-5520_U_E 12/13/04, 9:23 AM4

5

E N

G L

IS H

CONTENTS

FEATURES ................................................... 4 CAUTION: READ THIS BEFORE

OPERATING YOUR UNIT. .......................... 6 PRECAUTIONS ............................................. 9 COMPONENT NAMES ................................ 10 Main Unit ........................................................................... 10

Remote control .................................................................. 11

Loading Batteries ........................................................... 11

Handling the Remote Control ......................................... 11

INSTALLATION INSTRUCTIONS ................ 12 Installation ......................................................................... 12

Anti-tumble measures ....................................................... 12

Connecting to Video Imaging Device ............................... 13

Power Cord Connection .................................................... 14

OPERATING INSTRUCTIONS ..................... 15 Turning Power On and Off ................................................ 15

Input Switching ................................................................. 16

Volume Adjustment ........................................................... 16

Audio Mute ........................................................................ 16

Size Switching ................................................................... 17

Input Signal Screen Display ............................................. 18

Displaying MULTI PICTURE .............................................. 18

PICTURE MENU................................................................ 19

FUNCTION MENU ............................................................ 21

SETUP MENU ................................................................... 22

OTHER FEATURES ..................................... 23 Automatic Store ................................................................ 23

TROUBLESHOOTING ................................. 24 Symptoms That Appear to be Failures ............................. 24

PRODUCT SPECIFICATIONS ...................... 24 Signal Input ....................................................................... 25

Recommended Signal List ................................................ 26

INSTALLATION INSTRUCTIONS FOR PC... 27 Connecting to a PC........................................................... 27

Power Cord Connection .................................................... 28

OPERATING INSTRUCTIONS FOR PC........ 29 Turning Power On and Off ................................................ 29

Input Switching ................................................................. 30

Volume Adjustment ........................................................... 30

Audio Mute ........................................................................ 30

Size Switching ................................................................... 31

Input Signal Screen Display ............................................. 31

Automatic Adjustment of Screen Position and the Clock ....................................... 32

Independant Operation of Multiple Monitors .................... 32

Using the Menu Screen .................................................... 32

PICTURE MENU................................................................ 33

AUDIO MENU ................................................................... 34

TIMER MENU .................................................................... 34

FUNCTION MENU ............................................................ 35

SETUP MENU ................................................................... 36

LANGUAGE MENU ........................................................... 37

OTHER FEATURES FOR PC........................ 37 Automatic Store ................................................................ 37

Signal Check ..................................................................... 38

Power Save Mode ............................................................. 38

IMAGE RETENTION OF PLASMA DISPLAY PANEL ..................................................... 39

TROUBLESHOOTING FOR PC .................... 40 Symptoms That Appear to be Failures ............................. 40

Actions to Correct Abnormal Displays .............................. 42

PRODUCT SPECIFICATIONS FOR PC ........ 43 Signal Input ....................................................................... 43

Recommended Signal List ................................................ 44

011_PDM-5520_U_E 12/13/04, 9:23 AM5

6

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. This Plasma monitor has been designed and manufactured to meet international safety standards, but like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured. Before using this product, please read and understand the Safety Instructions thoroughly to ensure correct usage, and follow all the instructions.

Never use the monitor if a problem occurs. Abnormal operations such as smoke, strange odor, no image, no sound, excessive sound, damaged casing, elements, cables, penetration of liquids or foreign matter, etc. can cause a fire or electrical shock. In such case, immediately turn off the power switch and then disconnect the power plug from the power outlet. After making sure that the smoke or odor has stopped, contact your dealer. Never attempt to make repairs yourself because this could be dangerous.

Do not insert liquids or foreign objects. Penetration of liquids or foreign objects could result in fire or electrical shock. Use special caution in households where children are present. If liquids or foreign objects should enter the projector, immediately turn off the power switch, disconnect the power plug from the power outlet and contact your dealer. Do not place the monitor in a bathroom. Do not expose the monitor to rain or moisture. Do not place flower vases, pots, cups, cosmetics, liquids such as water, etc on or around the monitor. Do not place metals, combustibles, etc. on or around the monitor.

Never disassemble or modify the monitor. The monitor contains high voltage components. Modification could result in fire or electrical shock. Never remove any fixed cover.

Do not give the monitor any shock or impact. If the monitor should be shocked and/or broken, it could result in an injury, and continued use could result in fire or electrical shock. If the glass panel is broken or damaged, immediately turn off the power switch, disconnect the power plug from the power outlet and contact your dealer.

Do not place the monitor on an unstable surface. If the monitor should be dropped and/or broken, it could result in an injury, and continued use could result in fire or electrical shock. Do not place the monitor on an unstable, slanted or vibranting surface such as a wobbly or inclined stand.

Do not obstruct the ventilation of the monitor. If the ventilation is obstructed during the operation of the monitor or just after switching off the power, it could result in damage and shorten the lifespan of your monitor due to overheating. Make sure there is ample ventilation. Keep a space of 100mm (10cm) or more between the sides, rear and top of the monitor and other objects such as walls. Do not place anything around ventilation openings of the monitor. Never block ventilation openings. Do not put the plasma display panel side up. Do not cover the monitor with a tablecloth, etc. Do not place the monitor on a carpet or bedding, or near a curtain.

Use only the correct power outlet. Incorrect power supply could result in fire or electrical shock. Use only the correct power outlet depending on the indication on the monitor and the safety standard. The enclosed power cord must be used depending on the power outlet to be used.

Be cautious of the power cord connection. Incorrect connection of the power cord could result in fire or electrical shock. Do not touch the power cord with a wet hand. Check that the connecting portion of the power cord is clean (with no dust), before using. Use a soft and dry cloth to clean the power plug. Insert the power plug into a power outlet firmly. Avoid using a loose, unsound outlet or contact failure. Do not cut off the fitted power plug, the removal of which could lead to impaired performance. If you wish to extend the lead, obtain an

appropriate extension lead or consult your dealer. Should you require replacing the fuse in the molded plug with a new fuse, then please replace with new one of the same value, type and

approval as the original. Ensure the fuse cover is returned to its original position.

Be sure to keep safety ground connection. Connect the ground terminal of AC inlet of this monitor with the ground terminal provided at the power outlet using the enclosed power cord. If the provided plug does not fit your outlet, consult an electrician for replacement of the obsolete outlet.

011_PDM-5520_U_E 12/13/04, 9:23 AM6

7

E N

G L

IS H

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. (continued)

Be careful in handling the power cord and external connection cables. If you keep using a damaged power cord or cables, it can cause a fire or electrical shock. Do not apply too much heat, pressure or tension to the power cord and cables. If the power cord or cables are damaged (exposed or broken core wires, etc.), contact your dealer. Do not place the monitor or heavy objects on the power cord and cables. Also, do not place a spread, cover, etc, over them because this

could result in the inadvertent placing of heavy objects on the concealed power cord or cables. Do not pull the power cord and cables. When connecting and disconnecting the power cord or cables, do it with your hand holding the plug

or connector. Do not place the cord near the heater. Do not touch the power plug just after disconnecting it from the power outlet to prevent electric shock. Do not touch the power plug when lightening is close to you. Avoid coiling the power cord and bending it sharply. Protect the power cord from being walked on, pinched particularly at plugs, conveniences receptacles, and the point where they exit from

the apparatus. Do not modify the power cord.

Be careful in handling the battery of the remote control. Incorrect handling of the battery could result in fire or personal injury. The battery may explode if not handled properly. Keep the battery away from children and pets. If swallowed consult a physician immediately for emergency treatment. Do not allow the battery to be exposed to fire or water. Avoid fire or high-temperature environment. Do not hold the battery with metallic tweezers. Keep the battery in a dark, cool and dry place. Do not short circuit the battery. Do not recharge, disassemble or solder the battery. Do not physically impact the battery. Use only the battery specified in the manual of this monitor. Make sure the plus and minus terminals are correctly aligned when loading the battery. If you observe a leakage of the battery, wipe out the liquid and then replace the battery. If the liquid adheres your body or clothes, rinse well

with water. Obey the local laws on disposing the battery.

Be careful in moving the monitor. Neglect could result in an injury or damage. Do not move the monitor during use. Before moving, disconnect the power plug and all external connections. You are advised to move the monitor with two persons. Avoid any impact or shock to the monitor; particularly take care of glass screen.

Do not put anything on top of the monitor. Placing anything on the monitor could result in loss of balance or falling, and cause an injury or damage. Use special caution in households where children are present.

Avoid a humid or dusty place. Placing the monitor in a smoke, a highly humid, dusty place, oily soot or corrosive gas could result in fire or electrical shock. Do not place near the kitchen, a humidifier or other place where there is oil, smoke or humidity.

Avoid a high temperature environment. The heat could have adverse influence on the monitor and other parts, and could result in transformation, melting or fire. Do not place the monitor, the remote control and other parts in direct sunlight or near a hot object such as heater, etc. Do not put the monitor in a place where the temperature is widely changing.

Remove the power cord for complete separation. For safety purposes, disconnect the power cord if the monitor is not to be used for prolonged periods of time. Before cleaning, turn off and unplug the monitor. Neglect could result in fire or electrical shock.

How to view the monitor If you use the monitor in too dark a room, your eyes may become tired. Please use it in a reasonably bright room. Avoid direct rays of the sun to the screen in order to prevent eye fatigue. Your eyes will get fatigued after viewing the monitor for long period of time. Relax your eyes by viewing away from the monitor from time to time. Please watch the monitor in downward direction.

011_PDM-5520_U_E 12/13/04, 9:23 AM7

8

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. (continued)

Note on image retention The plasma monitor illuminates phosphor to display images. The phosphor has a finite illumination life. After extended periods of illumination, the brightness of the phosphor will be degraded to such extent that stationary images would burn-in that part of the screen as grayed-out images. Tips to prevent such image retention are: - Do not display images having sharp brightness differences or high-contrast images, such as monochrome characters and graphic patterns,

for long. - Do not leave stationary images appearing for long, but try to refresh them at appropriate intervals of time, or try to move them using screen

saver function. - Turn down the contrast and brightness controls.

How to clean the plasma display panel of the monitor Before cleaning the monitor, turn off the monitor and disconnect the power plug from the power outlet. To prevent scratching or damaging the plasma display panel face, do not knock or rub the surface with sharp or hard objects. Clean the screen with a soft cloth moistened with warm water and dry with a soft cloth. If it is not enough, then use a cloth with mild detergent. Do not use harsh or abrasive cleaners.

How to clean the cabinet of the monitor Use a soft cloth to clean the cabinet and control panel of the monitor. When the plasma monitor is excessively soiled dilute a neutral detergent in water, wet and wring out the soft cloth and afterward wipe with a dry soft cloth. Never use acid/alkaline detergent, alcoholic detergent, abrasive cleaner, powder soap, OA cleaner, car wax, glass cleaner, etc. especially because they would cause discoloration, scratches or cracks.

Prevention of an obstacle to Radio receivers This monitor has been designed pursuant to the international EMI standards. This is to prevent a problem to Radio receivers. - Keep the monitor away from Radio. - Adjust Radio antennas in order for the monitor not to receive interference. - The antenna cable of Radio should be kept away from the monitor. - Use a coaxial cable for antenna. You can check if this monitor influences Radio receivers by turning off all other equipment other than the monitor. If you find a problem receiving Radio when using the monitor, check the instructions mentioned above.

Precautions for the cable connection - Do ensure that all connections, (including the power plug, extension leads and interconnections between the pieces of equipment), are

properly made and in accordance with the manufacturers instructions. Switch off and withdraw the power plug before making or changing connections.

- Confirm the connector is fixed tightly when the signal cable is connected. Also confirm the screws on the connector are tightened.

- Plug the power cord of the monitor into a different socket from that for other equipment, such as Radio etc. - Use a plug with ground terminal and make sure that it connects to the ground.

Precaution during transportation Please pay attention when you transport this monitor because it is heavy. Furthermore, use the original carton box and its packaging materials when the monitor is transported. Failure to transport the monitor in any carton except the original carton may result in damage to the monitor. Save the original carton box and all packing material.

Do not physically impact the remote control. A physical impact could cause damage or malfunction of the remote control. Take care not to drop the remote control. Do not place heavy objects on the remote control.

Avoid strong rays. Any strong rays (such as direct sun rays or room lighting) onto the remote control sensors could invalidate the remote control.

Avoid radio interference. Any interfering radiation could cause distorted images or noises. Avoid radio generator such as a mobile telephone, transceiver, etc. around the monitor.

Set the sound volume at a suitable level. It is better to keep the volume level low and close the windows at night to protect the neighborhood environment.

011_PDM-5520_U_E 12/13/04, 9:23 AM8

9

E N

G L

IS H

CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. (continued)

Precautions for the installation - Do not use makeshift pedestals and NEVER fix legs with wood screws - to ensure complete safety, always fit the manufacturers approved

pedestal or legs with the fixings provided according to the instructions. - Use only with the cart, pedestal, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used,

use caution when moving the cart/apparatus combination to avoid injury from tip-over. - This product is designed to comply with the recommended safety standards for tilt and stability. Do not apply excessive pulling force to the

front, or top, of the cabinet that could cause the product to overturn resulting in product damage and/or personal injury. - Follow instructions for wall, shelf or ceiling mounting as recommended by the manufacturer. - Only use the attachments/accessories specified by the manufacturer. - Consult your dealer if you are in any doubt about installation, operation or safety of your equipment.

Other precautions - Do not leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended operation or has

a stand-by mode. Switch off using the switch on the equipment and show your family how to do this. Make special arrangements for infirm or handicapped people.

- Disposal of this product may require specific instructions pertaining to your resident region. - Never guess or take any chances with electrical equipment of any kind - it is better to be safe than sorry!

PRECAUTIONS

Please read this User's Manual thoroughly, especially the "IMPORTANT SAFETY INSTRUCTIONS" and the "CAUTION: READ THIS BEFORE OPERATING YOUR UNIT." and the "PRECAUTIONS" sections. Mis-use may cause damage to your plasma monitor, which could shorten its lifespan, or cause injury to yourself. Should you encounter any difficulty in the set-up or operation of your monitor, firstly refer to the Troubleshooting guide at the rear of this manual. In the unlikely event of a problem occurring with your plasma monitor, switch off at the mains sockets, pull out the plugs, and contact your dealer immediately.

Under no circumstances remove the rear cover of your plasma monitor. Never guess or take any chances with electrical equipment of any kind - it is better to be safe than sorry!

It is prohibited for the end user of this product to copy, reverse engineer or reverse compile the software included therein, save to the extent permitted by law.

After the plasma monitor has been turned on for any length of time, you will notice that the screen becomes warm. Please note that this is normal. Sometimes the screen might have some tiny bright or dark spots. Please note that this is normal.

To prevent scratches or damages to the plasma display panel, do not knock or rub the surface with sharp or hard objects.

011_PDM-5520_U_E 12/13/04, 9:23 AM9

10

(6 12W)

(6 12W)

(6 12W)

COMPONENT NAMES

Main Unit

Cabinet (front frame)

Pedestal (option)

Panel

Front

Control panel

Adjustment buttons are located on the bottom.

The back cover is provided with indications to distinguish the adjustment buttons.

32

( ) indicates the function while the MENU is displayed on the screen.

The main power switch is located at the back, on the lower surface.

Remote-control receiver

Indicating lamp

Main power switch 15

11

15

Menu button

INPUT SELECT button (OK button) 16

RECALL button ( SELECT button)

SIZE button ( SELECT button)

17

15SUB-POWER button

VOLUME UP/DOWN buttons ( ADJUST buttons)

16 18

Caution when moving the main unit As this product is heavy, whenever it is moved, two or

more people are required to transport it safely. Whenever carrying this product, hold it by the top and

bottom on both ends. Attached parts could come loose, causing the product to fall and possibly causing injury.

Rear

External speaker terminals

External speaker terminals

13 13

External device connection terminals

13 27

+

012_PDM-5520_U_E 12/13/04, 9:23 AM10

11

E N

G L

IS H

Loading Batteries

1. Open the battery cover. Slide back and remove the battery

cover in the direction of the arrow.

2. Load the batteries. Load the two Size AA batteries included, matching polarity

markings on the batteries to those on the case.

3. Close the battery cover. Replace the battery cover in the

direction of the arrow and snap it back into place.

Handling the Remote Control

Use the remote control within 5m from the front of the unit, within a 30 degree arc either side of the remote control sensor.

CAUTION Do not use new and old batteries together. The batteries could

explode or leak, resulting in fires, physical injury, or stains. When loading batteries, observe their correct polarities as

marked on the product. If loaded in the wrong direction, the batteries could explode or leak, resulting in fires, physical injury, or stains.

ATTENTION Do not drop or exert undue force on the remote control. To avoid possible failures. Do not splash the remote control with

water or put it on a wet object. If you do not intend to use the remote control for an extended

period of time, remove the batteries from it. If the remote control begins to lack responsiveness, replace the

batteries. Strong light such as direct sunlight impinging on the

photoreceptor of the remote control can cause operational failure. Position this unit to avoid direct contact with such light.

COMPONENT NAMES (continued)

Remote control

AV1 AV2

RGB 1 RGB 2

AV3

MUTE VOL

AV4

AUTO PIN P

OK

SIZE RECALL

MENU

ID ID SET

15POWER OFF button 15

POWER ON button

MUTE button

RGB/VIDEO buttons

PINP button

AUTO button

MENU button

OK button

ID button

15

16

16

18

32

32

32

32

16

17

18

18

32

POWER ON/OFF button

VOLUME UP/DOWN buttons

SIZE button

RECALL button

RETURN button

SELECT/ADJUST button

ID SET button

With in 30 degrees

About 5m

About 3m

With in 30 degrees

About 3m

AV1 AV2

RGB 1 RGB 2

AV3

MUTE VOL

AV4

AUTO PINP

OK

SIZE RECALL

MENU

ID ID SET

32

012_PDM-5520_U_E 12/13/04, 9:23 AM11

12

Anti-tumble measures

CAUTION Have this unit mounted in a stable place. Take measures to prevent it from tumbling down to avoid possible physical injury.

Securing to a wall or pillar Use a commercially available cord or chain, and a clamp to secure the set to a firm wall or pillar.

Securing to a desktop 1)Using wood screws (two), fasten the set to the clamping screw holes on the rear of the pedestal as shown.

2)Using commercially available wood screws, secure the set firmly in position.

INSTALLATION INSTRUCTIONS

Installation If you have purchased the model without the pedestal attached:

When installing the monitor, use the optional pedestal. The pedestal has been used for the illustrations in this manual.

CAUTION Use one of commercially available mount units to install this product. A mount of insufficient

strength or inadequate design can cause overturning or dropping and result in fire, electrical shock or injury. Please note that our company assumes absolutely no responsibility for personal injuries or property damage caused by improper installation.

Installation of the wall mount unit and ceiling mount unit can be dangerous, so do not attempt this work yourself. Ask your dealer to provide the name of a qualified installer.

In order to prevent an internal temperature increase, maintain a space of 10cm (4 inches : For a desktop set-up) or more between the sides and other objects such as walls, etc., so that the ventilation holes are not blocked. ()

10cm (4 inches) or more*

cord or chain

clamp Wall or Pillar

cord or chain

clamp Wall or Pillar

Hook

Cord or Chain

Two places Wood screw

012_PDM-5520_U_E 12/13/04, 9:23 AM12

13

E N

G L

IS H

(1) Make sure that the power switch of the monitor is turned off. (2) Make sure that the power switch of the imaging device is turned off. (3) Use a commercially available cable and connector to connect the signal input terminal on the rear panel of this

device and the signal output terminal of the imaging device.

INSTALLATION INSTRUCTIONS (continued)

Connecting to Video Imaging Device

Read CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. and PRECAUTIONS ( to ) carefully to ensure maximum safety before proceeding to these steps: Choose a safe, level location to install the product.

Install the monitor in a location with easy access to a power socket. Make sure that the power switch of this device is turned off.

6 9

If video equipment with an S video output terminal is used, connection with S video cable is recommended to provide finer video quality. (If the S-video input terminal and the video input terminal of AV3 connect to the monitor at the same time, S-video input would govern.)

If the OUTPUT (MONITOR) terminal is connected to an external monitor with a 75 Ohm terminal, it is possible to view the same image as on the monitor. But it is possible to monitor only the composite video signal from AV1, AV2, AV3 or AV4 input that is displayed on the screen at the time.

If the adaptor (included) is applied to AV4 input as shown in the drawing, it is impossible to receive RGB signal.

[An example of connecting video imaging device]

DVI-STB and RGB component setup

To Subwoofer

To component video equipment Please use connection cable suitable for the terminal form of video equipment.

Terminal

Signal

AV1

AV2

AV3

AV4

RGB1

RGB2

CVBS

S-video

Component

RGB

PC

STB

RGB

Component

Remarks

Refer to Setup Menu.

Refer to Setup Menu.

Refer to Setup Menu.

Refer to Setup Menu.

RCA/SCART DVI D-sub

Applicable video signals for each input terminal (See PRODUCT SPECIFICATIONS for details. )24

22

22

23

23

Monitor rear panelSpeaker (R) Speaker (L)

Power cord

(612W)

(612W)

Use if the video equipment has an S-video input terminal.

To S video output

term inal

To audio output term

inals

To audio output term

inals

To com ponent

output term inals

To com ponent

output term inals

To com ponent

input term inals

To com ponent

input term inals

To com posite

input term inal

To audio output term

inals

To audio input term

inals

20 18 16 14 12 10 8 6 4 2

21 19 17 15 13 11 9 7 5 3 1

VCR

VCR

DVD player Set-Top Box

Video disc player

Adaptor

To com posite

output term inal

S-video/Composite video

Do not connect both plugs at the same time. Use either of them.

( : available)

SUB WOOFER

012_PDM-5520_U_E 12/13/04, 9:23 AM13

14

INSTALLATION INSTRUCTIONS (continued)

Power Cord Connection Connect the power cord after completing all other connections.

1 Connect the power cord to this monitor. 2 Connect the power cord plug to the power outlet.

(The type of plug is different from this drawing for some countries.)

CAUTION Use only the power cord provided. Do not use a power supply voltage other than that indicated (AC100-240V, 50/60Hz) as this may cause fire or electric shock.

012_PDM-5520_U_E 12/13/04, 9:23 AM14

15

E N

G L

IS H

OPERATING INSTRUCTIONS

Indicating lamp

(6 12W)

Main power switch

SUB-POWER button

AV1 AV2

RGB 1 RGB 2

AV3

MUTE VOL

AV4

AUTO PIN P

OK

SIZE RECALL

MENU

ID ID SET

POWER ON/OFF button

POWER OFF button

POWER ON button

Turning Power On and Off

To turn the monitor power on, press the main power switch on the monitor to ON, and then press the SUB POWER button or the ON/OFF or ON button on the remote control.

To turn the monitor power off, press the SUB POWER button or the ON/OFF or OFF button on the remote control, and then set the main power switch on the monitor to OFF. During normal use, the main power switch is set in the ON

position, and the monitor can then be turned ON/OFF using the SUB POWER button or the ON/OFF button on the remote control.

Indicating lamp

When the indicating lamp lights orange or the message No Sync. Signal, Power Save or Invalid Scan Freq. appears on the screen, see Power Save Mode or Symptoms That Appear to be Failures.

ATTENTION Avoid repeatedly turning the monitor on and off at short

intervals. Failures might result from such operation. Turn off the main power switch if you do not plan to use the

monitor for an extended period of time. If a power failure occurs while the monitor is running, it will be

powered on upon recovery from the failure. Turn off the unit main power switch before you leave the area in which the monitor is located.

38 40

Indicating lamp

Off

Lights red

Lights green

Lights orange

Power status

Off

Off (standby)

On

Off (Power Save)

Operating

When the main power switch is set to OFF.

When the main power switch is ON, and the OFF button on the remote control or the SUB POWER button on the underside of the front of the frame is OFF.

When the main power switch is ON, and the ON button on the remote control or the SUB POWER button on the underside of the front of the frame is ON.

When the main power switch is ON, and the ON button on the remote control or the SUB POWER button on the underside of the front of the frame is ON. However, the indicator also light orange when the unit is in POWER SAVE mode.

013_PDM-5520_U_E 12/13/04, 9:23 AM15

16

OPERATING INSTRUCTIONS (continued)

SIZE button

INPUT SELECT button

AV1 AV2

RGB 1 RGB 2

AV3

MUTE VOL

AV4

AUTO PIN P

OK

SIZE RECALL

MENU

RGB/VIDEO buttons

SIZE button

VOLUME UP/DOWN buttons

MUTE button

Input Switching

AV1 AV2 AV3

RGB2 RGB1 AV4

Input can be switched by pressing the AV1, AV2, AV3, AV4, RGB1 or RGB2 buttons of the remote control.

Input can be switched in the sequence of AV1 AV2 AV3 AV4 RGB1 RGB2 by pressing the INPUT SELECT button of the monitor.

Volume Adjustment

The volume can be adjusted by pressing the VOL+ and VOL- buttons of the remote control (or the and volume buttons of the monitor unit).

When a button is pressed, the volume adjustment status guide will be displayed. The volume will increase when the VOL+ (or ) button is

pressed while the guide is being displayed. The volume will decrease when the VOL- (or ) button is

pressed while the guide is being displayed.

Audio Mute

Volume 15

Volume setting value

Adjustment status guide display

The audio volume can be temporarily muted by pressing the MUTE button of the remote control.

When a button is pressed, the volume adjustment status guide (magenta) will be displayed.

The volume setting can be lowered by pressing the VOL- button while the audio is mute.

The muting can be cancelled by pressing the VOL+ button or MUTE button while the audio is mute.

When the MUTE button of the remote control is pressed again, the audio will be restored and the volume display (green) will appear.

Volume 15

Volume setting value

Adjustment status guide display (The display color will change to magenta.)

VOLUME UP/DOWN buttons

+

+

+

013_PDM-5520_U_E 12/13/04, 9:23 AM16

17

E N

G L

IS H

Vertical picture position can be adjusted for [Panoramic], [Zoom] and [Cinema] mode as follows. 1. Press the SIZE button and SELECT buttons during picture size display. 2. The position display will appear. 3. The adjustment range of each picture size is as shown below.

[Panoramic] - 12 to + 12 [Zoom] and [Cinema] - 31 to + 31

4. When 1080i/60 component signal is received, vertical position can be adjusted only one step up. (The range: 0 to +1)

Position + 31 Position - 31

PressPress

ATTENTION Using a wide-screen monitor This monitor has a screen mode selection feature. If an incompatible screen mode is selected to play certain software, such as a TV

program, the image will appear different from the original. Take this into consideration when making screen mode choices. Use of this monitor in its enlarged display mode with the wide feature enabled in coffee shops, hotels and other establishments for

commercial or public viewing purposes could infringe on the copyright holders rights protected by Copyright Law. When a normal 4:3 image is displayed over the entire screen in the Panoramic mode, parts of the periphery of the image may disappear

and/or appear distorted in some cases. Use the 4:3 mode to view images which were created in 4:3 mode. This mode allows 4:3 content to be viewed without picture distortion.

Each time the SIZE button of the remote control or the monitor is pressed, the screen display size will change in sequence and the status will be displayed at the bottom of the screen.

During VIDEO signal input (AV1, AV2, AV3, AV4, RGB1 (set to [DVI-STB]) and RGB2 (set to [Component])

The size will be fixed Full mode and not change when receiving the component signal of 1080i/50, 1080i/60 or 720p/60.

Display size selection diagram

4:3 Panoramic Zoom

Full Cinema

Full

Size Switching

Play a 4:3 image in a 16:9 screen.

Play a 4:3 image in a 16:9 screen with the height and width of the middle of the screen enlarged on equal scales and with both sides appearing somewhat enlarged.

Play a 16:9 VISTA size image from a 4:3 image faithfully reproduced on the 16:9 screen.

Play a 21:9 Cinema size image from a 4:3 image expanded vertically on the 16:9 screen.

Play a 4:3 image faithfully in a 16:9 screen in the standard vertical size and horizontally squeezed.*

Blanking occurs on both sides.

The 4:3 image is called a letterbox image.

In some cases, some slight blanking may remain at the top and bottom.

In some cases, some slight blanking may remain at the top and bottom.

* An image with an aspect ratio of 16:9 shrunk horizontally to 4:3 to display in a 4:3 screen

When you want to Set the display size Display screenInput signal Remarks

(4.:3 signal)

(Vista)

(Cinema)

(Squeeze)

4 : 3

Panoramic

Zoom

Cinema

Full

013_PDM-5520_U_E 12/13/04, 9:23 AM17

18

Off-timer On-timer

OPERATING INSTRUCTIONS (continued)

Displaying MULTI PICTURE

Input Signal Screen Display

If the PINP button on the remote control is pressed MULTI PICTURE will display.

Activating the P-in-P mode from the RGB input screen

Pressing the PINP button once will display 2 pictures. This mode can be available from RGB1 (DVI-PC) and

RGB2 (RGB) input. The speaker icon can be shifted left and right by pressing the

and SELECT buttons; the audio of the video will be output from the side on which the speaker icon is located.

The sub-screen position can be selected up and down by pressing

SELECT buttons. When the speaker icon appears on

the left of the subscreen, as in the illustration at right, you can use the AV1, AV2, AV3, or AV4 buttons to select the subscreen input mode.

Pressing the PINP button or the RETURN button will cancel the 2 pictures display.

Frequency Mode in the Setup Menu should be set to Movie when sub-screen is the component signal of 1080i/50 or 1080i/60.

AV1: Displays the VIDEO input signal of the sub-screen.

Activating the Split mode from the video input screen

Pressing the PINP button one time will display 2 pictures. The speaker icon can be shifted left

and right by pressing the and SELECT buttons; the audio of the video will be output from the side on which the speaker icon is located.

The same video input mode cannot be selected for both screens at the same time.

Pressing the PINP button or the RETURN button will cancel the 2 pictures display.

When the Video input is set to RGB Video, this Split mode is not possible.

Refer to the table for 2 pictures (Split) mode.2 pictures (Split)

NOTE Even if the input of the horizontal / vertical synchronizing signal (or video signal) stops in the MULTI PICTURE display, the mode will not

change to power save mode. Please be careful since image retention will occur if the plasma monitor is left in MULTI PICTURE display state for a long period of time.

The input signal status can be displayed on the screen by pressing the RECALL button of the remote control or the monitor. The display will go out in approximately 6 seconds.

( : available)

Input terminal

PAL-N NTSC-M , PAL-M

576i, 576p 480i, 480p 1080i/50 1080i/60 720p/60

STB Component

PAL-N

NTSC-M PAL-M

576i 576p

480i 480p

1080i/50

1080i/60

720p/60

STB Component

AV1 ~AV4

AV1 AV2

RGB1 RGB2

AV1~AV4 AV1, AV2 RGB1 RGB2

Main Sub

AV1 AV2

RGB 1 RGB 2

AV3

MUTE VOL

AV4

AUTO PIN P

OK

SIZE RECALL

MENU

ID ID SET

RECALL button

RECALL button

RETURN button

PINP button

RGB2 AV1

(Sub- screen)

AV1 AV2

Main Sub

AV1 Composite

-- -- Min. -- -- : -- --

OFF

Input mode Signal mode

013_PDM-5520_U_E 12/13/04, 9:23 AM18

19

E N

G L

IS H

OPERATING INSTRUCTIONS (continued)

PICTURE MENU Picture Audio Timer Function Setup Language Select OK Set

Picture Picture Mode Day Contrast +31 Brightness -31 Color 0 Sharpness +15 Tint 0 Color Temperature Normal Contrast Mode Normal Reset Reset Select Set ReturnOK

Picture Mode Day Next/Prev Select Return

Picture Picture Mode Day Contrast +31 Brightness -31 Color 0 Sharpness +15 Tint 0 Color Temperature Normal Contrast Mode Normal Reset Reset Select Set ReturnOK

Contrast Mode Normal Next/Prev Select Return

Picture Day YNR Off CNR Off Film Mode On PAL Comb Filter On LTI Off CTI Off Black Enhancement Off Auto Color Off Reset Reset Select Set ReturnOK

YNR Off Next/Prev Select Return

Picture Day YNR Off CNR Off Film Mode On PAL Comb Filter On LTI Off CTI Off Black Enhancement Off Auto Color Off Reset Reset Select Set ReturnOK

Auto Color Off Next/Prev On/Off Return

Picture Day Color Temp. Adjust Color Management Color Decoding Select Set ReturnOK

Picture Color Temp. Adjust On Amplitude Red 63 Green 0 Blue 31 Cut Off Red + 31 Green 0 Blue + 31 Reset Reset Select On/Off Return

Picture Day Color Temp. Adjust Color Management Color Decoding Select Set ReturnOK

Picture Color Management On Magenta + 60 Red + 30 Yellow 0 Green + 60 Cyan + 30 Blue 0

Reset Reset Select On/Off Return

Picture Day Color Temp. Adjust Color Management Color Decoding Select Set ReturnOK

Picture Color Decoding RGB R G B Red 0 Green + 60 Color 0 Tint + 31

Reset Reset

Select Return Exit

MENU OK

OK

OK

OK

OK

OK

OK

OK

013_PDM-5520_U_E 12/13/04, 9:23 AM19

20

Setup hint

Day: This setting is best for very bright ambient lighting. Night: This setting is for normal lighting conditions.

Adjust for maximum visibility to suit the ambient brightness. This can be adjusted further till [+40] by pressing and holding

cursor button at [+31]. The color for [+32] to [+40] numbers will change from white to magenta. This special mode is better for dark scenes. For normal viewing we recommend that the Contrast is set to [+31] or less. Panel Life in the Function Menu should be set to Normal when this Contrast setting is adjusted.

Depending on the source component, the picture may appear too dark or too bright. In this case, adjust the Brightness setting to suit your taste.

Adjust to taste

Normally set to Center position. Shift to the minus (-) side for a softer effect and plus (+) for a sharper picture.

This is adjustable when receiving PAL/SECAM signal. Then the character will be grayed out. Adjust for most realistic skin color.

Adjust to taste.

Dynamic: Emphasizes the differences between video shadings to improve the feeling of contrast.

Normal: The gradation of an image is reproduced as faithfully as possible.

Auto: Detects image brightness and automatically adjusts for natural brightness.

The original factory settings for the items of this Menu page can be restored by pressing the OK button.

Performs picture signal noise reduction. Turn up to reduce noise.

Performs color signal noise reduction. Turn up to reduce noise. It will be fixed as Off only when selecting DVI-STB mode.

On: Automatically detects the movie film material and faithfully reproduces the original film image.

Off: Set to OFF when switching between images does not appear natural.

This is available only when receiving a PAL composite signal. Turn On to reduce the discolorations in fine picture detail and provide purer color.

Adjusts the sharpness of the picture signal.

Adjusts the sharpness of the color signal.

Adjusts the black level compensation.

This is available only when receiving an NTSC composite/ S-Video signal. This monitors and adjusts the color to maintain constant color levels. It also maintains natural flesh tones while preserving fidelity of background colors.

Turn On when you wish to change color temperature depending on the user's preference.

Adjust color temperature depending on the users preference. These settings are independently stored in each of the 4 Color Temperature modes.

Selected characters

Picture Mode

Contrast

Brightness

Color

Sharpness

Tint

Color Temperature

Contrast Mode

Reset

YNR

CNR

Film Mode

PAL Comb Filter

LTI CTI Black Enhancement

Auto Color

Color Temp. Adjustment

Amplitude

Cut Off

Narrows the gap between brightness and darkness.

Black is subdued for increased overall darkness.

Darkness colors.

Soft

Enhances red and weakens green.

Brightness scenes are decreased in reddish color.

Brightness scenes are decreased in greenish color.

Brightness scenes are decreased in bluish color.

Dark scenes are decreased in reddish color.

Dark scenes are decreased in greenish color.

Dark scenes are decreased in bluish color.

Broadedns the gap between brightness and darkness.

Black is set off for increased overall brightness.

Lightens colors.

Sharp

Enhances green and weakens red.

(Selects the Reset mode)

Brighter scenes are increased in reddish color.

Brighter scenes are increased in greenish color.

Brighter scenes are increased in bluish color.

Dark scenes are increased in reddish color.

Dark scenes are increased in greenish color.

Dark scenes are increased in bluish color.

OPERATING INSTRUCTIONS (continued)

PICTURE MENU (continued)

Red

Green

Blue

Red

Green

Blue

Day Night

Cool Normal Warm Black / White

Normal Auto Dynamic

Off Low High

Off On

Off On

Off Low Middle High

Off On

Off On

013_PDM-5520_U_E 12/13/04, 9:23 AM20

21

E N

G L

IS H

OPERATING INSTRUCTIONS (continued)

PICTURE MENU (continued)

Setup hint

Turn On when the original balance of each color is required to adjust to suit user preferences.

This adjusts listed colors individually to make them either deeper or more pure. These settings are independently stored in each of the 4 Color Temperature modes.

Select the single color screen you need to adjust R/G/B level individually depending on the users preference. Set it back to RGB mode that indicates each color (R/G/B) mode after adjusting. Press the OK button every time the setting is changed.

This adjusts R/G/B levels or tints to make the color appear natural. These settings are independently stored in each of the 4 Color Temperature modes.

Selected characters

Color Management

Color Decoding

Magenta is weakened.

Red is weakened.

Yellow is weakened.

Green is weakened.

Cyan is weakened.

Blue is weakedned.

Darkenes red only.

Darkens green only.

Darkens colors.

Enhances red and weakens green.

Magenta is strengthened.

Red is strengthened.

Yellow is strengthened.

Green is strengthened.

Cyan is strengthened.

Blue is strengthened.

Lightens red only.

Lightens green only.

Lightens colors.

Enhances green and weakens red.

Magenta

Red

Yellow

Green

Cyan

Blue

Red

Green

Color

Tint

Off On

RGB R G B

FUNCTION MENU

Picture Audio Timer Function Setup Language Select OK Set

1 item is added to the Menu shown in the page .

Function Screen Saver Off Screen Wipe On 60Min. Black Side Panel Off Video Power Save Off Freeze Mode Split Default Zoom Panoramic Reset Reset Select Set Return

Setup hint

This is used to reduce power consumption for video input when there is no video signal. Setting it to On will place the monitor to the standby mode when the AV input with no signal is selected.

Selected characters

Video Power Save

Off On

Function Panel Life Normal Mode Display Off ID Number 1 Inverse On 60Min. Standby White Off Gamma 2.2 Reset Reset Select Set Return

MENU

OK

35

013_PDM-5520_U_E 12/13/04, 9:23 AM21

22

SETUP MENU

OPERATING INSTRUCTIONS (continued)

Picture Audio Timer Function Setup Language Select OK Set

Setup System System 2 Color System Video Input Audio Input Scart Output Monitor RGB1 DVI-STB RGB2 Component HDTV Select Set ReturnOK

Setup Color System

AV1 Auto AV2 NTSC-M AV3 PAL-M AV4 PAL-N

Select Return Exit

Setup System System 2 Color System Video Input Audio Input Scart Output Monitor RGB1 DVI-STB RGB2 Component HDTV Select Set ReturnOK

Setup Video Input

AV1 Auto AV2 Composite/Component AV3 Auto AV4 S-Video

Select Return Exit

Setup System System 2 Color System Video Input Audio Input Scart Output Monitor RGB1 DVI-STB RGB2 Component HDTV Select Set ReturnOK

Setup Audio Input AV1 Stereo AV2 L/Mono AV3 Stereo AV4 L/Mono Select Return Exit

Setup hint

Do not change the original setting. (System1 : Europe/Asia, System2 : North America)

This should correspond to the color system of the signal from the equipment that is connected to the AV1 video input terminal. Normally, set this to Auto. The system of the input signal will

be automatically recognized. If the input signal contains a lot of noise or has a low level at

Auto and the operation is erratic, set this to match the input signal.

When the component signal is received, this setting is not available (grayed out).

This should correspond to the signal mode of the signal from the equipment that is connected to AV1 video input terminal. Normally, set this to Auto. The signal mode of the input signal

will be automatically recognized. If the input signal contains a lot of noise or has a low level at

Auto and operation is erratic, set this to match the input signal.

This should correspond to the signal mode of the signal from the equipment that is connected to AV2 video input terminal.

This step should be set only when [Composite/Component] is selected on the 1st step. The procedure is same as for AV1.

If the signal from the equipment that is connected to the AV4 Scart input terminal is S-Video or Composite, set this to correspond to that signal.

If the signal is RGB, it will be automatically recognized and this setting will have no effect.

Selected characters

System

Color System

AV1

AV2

AV3

AV4

Video Input

AV1

AV2 (1st step)

AV2 (2nd step)

AV4

System1 System2

Auto NTSC-M PAL-N PAL-M

Auto HDTV SDTV/DVD

Auto HDTV SDTV/DVD

RGB Composite/Component

S-Video Composite

MENU OK

OK

OK

OK

(Same to AV1)

013_PDM-5520_U_E 12/13/04, 9:23 AM22

23

E N

G L

IS H

(Same to AV1)

Not Available (grayed out)

SETUP MENU (continued)

OPERATING INSTRUCTIONS (continued)

Automatic Store

OTHER FEATURES

Setup hint

This should correspond to the audio signal from the equipment that is connected to the AV1 audio input terminal. If the signal is monaural audio, set this to L/Mono.

This should correspond to the signal mode of the signal from the equipment that is connected to the RGB1 DVI terminal.

This should correspond to the signal mode of the signal from the equipment that is connected to the RGB2 D-sub terminal.

This step should be set only when [Component] is selected on the 1st step. This should correspond to the signal mode of the signal from the equipment that is connected to the RGB2 D-sub terminal. Normally, set this to Auto. The signal mode of the input

signal will be automatically recognized. If the input signal contains a lot of noise or has a low

level at Auto and the operation is found erratic, set this to match the input signal.

Selected characters

Audio Input

AV1

AV2

AV3

AV4 Scart Output

RGB1

RGB2 (1st step)

RGB2 (2nd step)

Stereo L/Mono

DVI-PC DVI-STB

RGB Component

Auto HDTV SDTV/DVD

Approximately 1 sec. after adjustment is completed, the adjustments will be recorded as shown in the table below.

Menu

Picture

Function Setup

Display

Yellow Green Cyan Blue

Color Decoding Red

Green Color

Tint Video Power Save System Color System

AV1 AV2 AV3 AV4

Video Input AV1 AV2 AV4

Audio Input AV1 AV2 AV3 AV4

RGB1 RGB2

Registration condition

1 setting is registered.

- For every Color Temperature, 1 setting is registered.

For every input function and every Picture Mode, 1 setting is registered. 1 setting is registered. 1 setting is registered. 1 setting is registered.

- 1 setting is registered.

- 1 setting is registered.

Menu

Picture

Display

Picture Mode Contrast Brightness Color Sharpness Tint Color Temperature Contrast Mode YNR CNR Film Mode PAL Comb Filter LTI CTI Black Enhancement Auto Color Color Temp. Adjust

R Amplitude G Amplitude B Amplitude

R Cut Off G Cut Off B Cut Off

Color Management

Magenta Red

Registration condition

1 setting is registered. For every input function and every Picture Mode, 1 setting is registered.

For every Color Temperature, 1 setting is registered.

For every input function and every Picture Mode, 1 setting is registered. 1 setting is registered.

The previously recorded items will be lost.

013_PDM-5520_U_E 12/13/04, 9:23 AM23

24

Symptoms That Seemingly Appear to be Failures

TROUBLESHOOTING

PRODUCT SPECIFICATIONS

See pagePoint to checkSymptom

The screen becomes dark and the images cannot be seen during VCR special playback (fast forward, rewind).

This sometimes occurs when a component output VCR such as the 480i is connected. This is not a malfunction; therefore, please take note that this may occur. When it does occur, change to composite output, or S-Video output.

Make the checks suggested below depending on the symptoms observed. If the symptoms remain uncorrected contact your dealer.

CAUTION Customer servicing can be hazardous.

Panel

Net dimensions (excluding pedestal)

Net weight (excluding pedestal)

Ambient conditions

Power supply

Power consumption/at standby

Audio output

(RGB input)

Input signals

Recommended signal

(Video input)

Input signals

Video output Signal

Recommended signal

Approx. 55 inches (1229 (H) x 691 (V) mm, diagonal 1410 mm)

1366 (H) x 768 (V) pixels

1394 (W) x 857 (H) x 105 (D) mm

63.5kg

Operating : 5C to 35C, Storage : 0C to 40C

Operating : 20% to 80%, Storage : 20% to 90% (non-condensing)

AC100 - 240V, 50/60Hz

530W / <3W

speaker 12W + 12W (6 ), sub woofer (RCA)

RGB1 DVI input terminal (DVI-D) RGB1 audio input terminal (3.5mm Stereo Mini Jack) RGB2 analog RGB input terminal (D-sub 15-pin) RGB2 audio input terminal (3.5mm Stereo Mini Jack)

0.7 V/1.0 Vp-p, analog RGB (Recommended Signal) 480i, 576i, 480p, 576p, 1080i/50, 1080i/60, 720p/60

H/V separate, TTL level [2K ] H/V composite, TTL level [2K ] Sync on green, 0.3 Vp-p [75 ]

47 modes

AV1: composite video input terminal (RCA) AV1: Y PB PR video input terminal (RCA) AV1: L/R audio input terminal (RCA) AV2: composite video input terminal (RCA) AV2: Y/G PB/B PR/R video input terminal (RCA) AV2: L/R audio input terminal (RCA) AV3: composite video input terminal (RCA) AV3: S video input terminal (RCA) AV3: L/R audio input terminal (RCA) AV4: composite video / S video / RGB / L/R audio input terminal (Scart)

AV1: NTSC-M, PAL-M, PAL-N AV1: 480i, 576i, 480p, 576p, 1080i/50, 1080i/60, 720p/60 AV2: NTSC-M, PAL-M, PAL-N AV2: 480i, 576i, 480p, 576p, 1080i/50, 1080i/60, 720p/60, RGB AV3: NTSC-M, PAL-M, PAL-N AV4: NTSC-M, PAL-M, PAL-N AV4: RGB

OUTPUT (MONITOR): composite video monitor-output terminal (RCA) OUTPUT (MONITOR): L/R audio monitor-output terminal (RCA) AV4: composite video / L/R audio monitor-output terminal (SCART)

13 modes

Display dimensions

Resolution

Temperature

Relative humidity

Input terminals

Video signals

Sync signals

Input terminals

Video signals

The monitor takes at least 30 minutes to attain optimal picture quality.

26 45

26

013_PDM-5520_U_E 12/13/04, 9:23 AM24

25

E N

G L

IS H

Signal Input

PRODUCT SPECIFICATIONS (continued)

RGB terminal (D-sub 15-pin connector)

Pin

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

Input signal

R (PR/CR)

G or sync on green (Y)

B (PB/CB)

No connection

No connection

R.GND (PR/CR, GND)

G.GND (Y, GND)

B.GND (PB/CB, GND)

No connection

GND

No connection

[SDA]

H. sync or H/V composite sync

V. sync. [V.CLK]

[SCL]

( ) : With component input

When different kinds of input signals are simultaneously input to the monitor via a graphics board or the like, the monitor will automatically select the signals in the following priority order:

*There may be instances when correct display is not possible even when displaying the signals listed on the following page. In this case, use H/V seperate sync or H/V composite sync.

Sync signal type

H/V seperate sync.

H/V composite sync.

sync. on Green *

Priority

1

2

3

Pin

1

2

3

4

Frame

Input signal

Y

Y-GND

C

C-GND

GND

S-input connector pin specifications

Scart connector pin specifications

Pin

1

2

3

4

5

6

7

8

9

10

11

Signal

AUDIO OUT (RIGHT)

AUDIO IN (RIGHT)

AUDIO OUT (LEFT/MONO)

AUDIO GND

RGB-B GND

AUDIO IN (LEFT/MONO)

RGB-B IN

AUDIO/RGB SWITCH / 16:9

RGB-G GND

Not Used

RGB-G IN

Pin

12

13

14

15

16

17

18

19

20

21

Signal

Not Used

RGB-R GND

GND

RGB-R / S.VHS CHROMINANCE IN

BLANKING SIGNAL

COMPOSITE VIDEO GND

BLANKING SIGNAL GND

COMPOSITE VIDEO OUT

COMPOSITE VIDEO / S.VHS LUMINANCE IN

GND / SHIELD (CHASSIS)

20 18 16 14 12 10 8 6 4 2

21 19 17 15 13 11 9 7 5 3 1

4 2

13

1

67890

-=~!@

2345

014_PDM-5520_U_E 12/13/04, 9:24 AM25

26

With Digital RGB signal input (RGB1 input)

The monitor differentiates the signal modes according to the horizontal and vertical sync signal polarities. Note that different signals having all these elements alike may be handled as the same signal.

Displaying images with more than 768 lines of vertical resolution at Full display (compressed display) can result in the interpolation of stripes.

Resolution

640 X 400

640 X 480

864 X 480

640 X 480

640 X 480

640 X 480

800 X 600

800 X 600

800 X 600

800 X 600

800 X 600

1024 X 768

1024 X 768

1024 X 768

720 X 480

1280 X 720

1920 X 1080

Vertical frequency (Hz)

70.08

59.94

59.94

72.81

75.00

85.01

56.25

60.32

72.19

75.00

85.06

60.00

70.07

75.03

59.94

60.00

60.00

Horizontal frequency

(kHz)

31.47

31.47

31.47

37.86

37.50

43.27

35.16

37.88

48.08

46.88

53.67

48.36

56.48

60.02

31.47

45.00

33.75

Dot clock frequency

(MHz)

25.18

25.18

34.24

31.50

31.50

36.00

36.00

40.00

50.00

49.50

56.25

65.00

75.00

78.75

27.00

74.25

74.25

No.

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

Signal Name

VGA

W-VGA

VESA

480p

720p/60

1080i/60

Remarks

WVGA type : On

EIA-861

EIA-861

EIA-861

Signal Mode

Recommended Signal List

PRODUCT SPECIFICATIONS (continued)

With Composite Input (AV1~AV4 input) and S-video Input (AV3 input).

Resolution

525

625

Vertical frequency (Hz)

59.94

50.00

Horizontal frequency (kHz)

15.73

15.63

Dot clock frequency (MHz)

No.

1

2

Signal Name

NTSC-M PAL-M

PAL-N

Remarks Signal Mode

With R, G, B Video input (AV2 and AV4 input).

Resolution

525 625

Vertical frequency (Hz) 59.94 50.00

Horizontal frequency (kHz)

15.73 15.63

Dot clock frequency (MHz)

No.

1

Signal Name

(NTSC-M, PAL-M) (PAL-N)

Signal Mode

With component input (AV1, AV2 and RGB2-component input).

Resolution

576

480

576

480

1080

1080

720

Vertical frequency (Hz)

50.00

59.94

50.00

59.94

50.00

60.00

60.00

Horizontal frequency (kHz)

15.63

15.73

31.26

31.47

28.13

33.75

45.00

Dot clock frequency (MHz)

No.

1

2

3

4

5

6

7

Signal Name

576i

480i

576p

480p

1080i/50

1080i/60

720p/60

Remarks Signal Mode

DVI-PC

DVI-STB

Setup Menu Condition

Remarks

( : acceptable)

014_PDM-5520_U_E 12/13/04, 9:24 AM26

27

E N

G L

IS H

INSTALLATION INSTRUCTIONS FOR PC

Read CAUTION: READ THIS BEFORE OPERATING YOUR UNIT. and PRECAUTIONS ( to ) carefully to ensure maximum safety before proceeding to these steps: Choose a safe, level location to install the product.

Install the monitor in a location with easy access to a power socket. Make sure that the power switch of this device is turned off.

(1) Make sure that the display signal of the personal computer to be used is compatible with the specifications of this device. See Product Specifications for PC concerning the specifications of this device. ~

(2) Make sure that the power switch of the personal computer is turned off. (3) Connect the signal input terminal (RGB 1 or RGB 2) on the rear panel of this monitor to the display signal output

terminal of the personal computer. Use a cable that fits the input terminal of this device and the output terminal of the personal computer. Depending on the type of personal computer being connected, the use of an optional conversion adapter or the adapter provided with

the personal computer may be necessary in some cases. For details, refer to the instruction manual of the personal computer, or ask the personal computer manufacturer or your local retail dealer.

6 9

Connecting to a PC

43 45

(612W)

(612W)

Monitor rear panel

Power cord

Power cable connector

PC

(D-sub) (RCA pin plug)(DVI)

To signal output terminal

To signal output terminal

To audio output terminal

To audio sub woofer

3.5mm Stereo mini jack

SUB WOOFER

Speaker (L)Speaker (R)

014_PDM-5520_U_E 12/13/04, 9:24 AM27

28

INSTALLATION INSTRUCTIONS FOR PC (continued)

Power Cord Connection Connect the power cord after completing all other connections.

1 Connect the power cord to this monitor. 2 Connect the power cord plug to the power outlet.

(The type of plug is different from this drawing for some countries.)

CAUTION Use only the power cord provided. Do not use a power supply voltage other than that indicated (AC100-240V, 50/60Hz) as this may cause fire or electric shock.

014_PDM-5520_U_E 12/13/04, 9:24 AM28

29

E N

G L

IS H

OPERATING INSTRUCTIONS FOR PC

Indicating lamp

(6 12W)

Main power switch

SUB-POWER button

AV1 AV2

RGB 1 RGB 2

AV3

MUTE VOL

AV4

AUTO PIN P

OK

SIZE RECALL

MENU

ID ID SET

POWER ON/OFF button

POWER OFF button

POWER ON button

Turning Power On and Off

To turn the monitor power on, press the main power switch on the monitor to ON, and then press the SUB POWER button or the ON/OFF or ON button on the remote control.

To turn the monitor power off, press the SUB POWER button or the ON/OFF or OFF button on the remote control, and then set the main power switch on the monitor to OFF. During normal use, the main power switch is set in the ON

position, and the monitor can then be turned ON/OFF using the SUB POWER button or the ON/OFF button on the remote control.

Indicating lamp

When the indicating lamp lights orange or the message No Sync. Signal, Power Save or Invalid Scan Freq. appears on the screen, see Power Save Mode or Symptoms That Appear to be Failures.

ATTENTION Avoid repeatedly turning the monitor on and off at short

intervals. Failures might result from such operation. Turn off the main power switch if you do not plan to use the

monitor for an extended period of time. If a power failure occurs while the monitor is running, it will be

powered on upon recovery from the failure. Turn off the unit main power switch before you leave the area in which the monitor is located.

38 40

Indicating lamp

Off

Lights red

Lights green

Lights orange

Power status

Off

Off (standby)

On

Off (Power Save)

Operating

When the main power switch is set to OFF.

When the main power switch is ON, and the OFF button on the remote control or the SUB POWER button on the underside of the front of the frame is OFF.

When the main power switch is ON, and the ON button on the remote control or the SUB POWER button on the underside of the front of the frame is ON.

When the main power switch is ON, and the ON button on the remote control or the SUB POWER button on the underside of the front of the frame is ON. However, the indicator also light orange when the unit is in POWER SAVE mode.

014_PDM-5520_U_E 12/13/04, 9:24 AM29

30

OPERATING INSTRUCTIONS FOR PC (continued)

Volume Adjustment

The volume can be adjusted by pressing the VOL+ and VOL- buttons of the remote control (or the and volume buttons of the monitor unit).

When a button is pressed, the volume adjustment status guide will be displayed. The volume will increase when the VOL+ (or ) button is

pressed while the guide is being displayed. The volume will decrease when the VOL- (or ) button is

pressed while the guide is being displayed.

Audio Mute

Input Switching Input can be switched by pressing the RGB1 or RGB2

buttons of the remote control.

Volume 15

Volume setting value

Adjustment status guide display

The audio volume can be temporarily muted by pressing the MUTE button of the remote control.

When a button is pressed, the volume adjustment status guide (magenta) will be displayed.

The volume setting can be lowered by pressing the VOL- button while the audio is mute.

The muting can be cancelled by pressing the VOL+ button or MUTE button while the audio is mute.

When the MUTE button of the remote control is pressed again, the audio will be restored and the volume display (green) will appear.

Volume 15

Volume setting value

Adjustment status guide display (The display color will change to magenta.)

VOLUME UP/DOWN buttons

INPUT SELECT button

AV1 AV2

RGB 1 RGB 2

AV3

MUTE VOL

AV4

AUTO PIN P

OK

SIZE RECALL

MENU

ID ID SET

VOLUME UP/DOWN buttons

MUTE button

RGB button

+

+

+

014_PDM-5520_U_E 12/13/04, 9:24 AM30

31

E N

G L

IS H

OPERATING INSTRUCTIONS FOR PC (continued)

Size Switching

AV1 AV2

RGB 1 RGB 2

AV3

MUTE VOL

AV4

AUTO PIN P

OK

SIZE RECALL

MENU

ID ID SET

RECALL button

SIZE button

RECALL button

SIZE button

Each time the SIZE button of the remote control or the monitor is pressed, the screen display area will change in sequence and the status will be displayed at the bottom of the screen.

* This mode is only available for VGA (640 X 480), SVGA (800 X 600), XGA (1024 X 768), WVGA (1280 X 768).

Display area selection diagram (RGB input)

RGB2 RGB

H : 48.4kHz V : 60.1 Hz

-- -- Min. -- -- : -- --

OFF

Normal Full Zoom1

Real Zoom3 Zoom2

Input Signal Screen Display

Resolution

Display

640 X 480 (VGA)

800 X 600 (SVGA)

1024 X 768 (XGA)

1280 X 768 (WXGA)

1280 X 1024 (SXGA)

1600 X 1200 (UXGA)

1366 X 768 (WXGA)

Full display

Full Normal Real Zoom1 Zoom2 Zoom3

Circular display

Processes such as compression (thinning) and expansion are performed for the above signal display. Because of this, there is a possibility that flicker may become noticeable on Zoom (1 ~ 3) depending on the display contents. If this occurs, turning the Vertical Filter On can reduce the flicker.

The input signal status can be displayed on the screen by pressing the RECALL button of the remote control or the monitor. The display will go out approximately 6 seconds.

Off-timer On-timer

Input mode

Signal mode

Input horizontal frequency

Input vertical frequency

cant select

36

cant select

014_PDM-5520_U_E 12/13/04, 9:24 AM31

32

OPERATING INSTRUCTIONS FOR PC (continued)

Using the Menu Screen (on-screen display system)

Automatic adjustment of Screen Position and the Clock

Adjustment of the screen to a position suitable for the PC signal and the clock adjustment can be performed automatically by pressing the AUTO button of the remote control.

CAUTION Perform this adjustment for each input (RGB1 or RGB2) and for each signal.

* Depending on the signal, satisfactory adjustment may not be possible in some cases. In such cases, adjust by referring to the Setup Menu item.

Setting the ID No. of the remote control allows separate control of up to a maximum of seven monitors. Remote control ID No. 2 (initially ID No. 1) can be set by pressing the ID SET button for 2 sec. or more while holding down the ID button. The number will be incremented (26712) when this button pressed continuously.

The ID remote control is operated by pressing the various buttons while holding down the ID button; Operation is possible only when the remote control and monitor ID Nos. are the same. The remote control can be operated normally by pressing the

various remote control buttons without holding down the ID button. Set the monitor using the ID No. of Function MENU.

Independant Operation of Multiple Monitors (ID No)

The remote control ID No. can be checked by pressing the ID SET button while holding down the ID button.

Monitor ID No.

Remote control ID No.

When the MENU button is pressed, the adjustment menu screen will be displayed; from there, PC signal adjustment and setting is possible by using the SELECT button, ADJUST button and OK button. Refer to ~ concerning the adjustment items and the

settings.

Example: Selecting the Picture screen

1. Press the MENU button to display the Main Menu screen.

2. Press the OK button to display the Picture Menu screen. (Use the and SELECT buttons to select other items.)

3. Use the and SELECT buttons to select the item to be adjusted and then use the and ADJUST buttons to adjust (example: Contrast).

Press the RETURN button to return to the previous screen. If there is no operation for a period of one minute, the

Adjustment Menu screen will be closed automatically.

AV1 AV2

RGB 1 RGB 2

AV3

MUTE VOL

AV4

AUTO PIN P

OK

SIZE RECALL

MENU

ID ID SET

ID Number Monitor [ 1 ] R/C [ 1 ]

MENU

Picture Audio Timer Function Setup Language Select OK Set

33 37

OK

Picture Contrast : + 31 Brightness : 31 Color : 0 Tint : + 31 Picture Enhancement : Off Color Temperature : Normal Color Temp. Adjust Reset Reset Select Return Exit

Contrast + 31 Next / Prev Adjust Return

AUTO button

MENU button

ID button

RETURN buttons

SELECT/ADJUST buttons

OK button

ID SET button

35

015_PDM-5520_U_E 12/13/04, 9:24 AM32

33

E N

G L

IS H

OPERATING INSTRUCTIONS FOR PC (continued)

PICTURE MENU

Picture Audio Timer Function Setup Language Select OK Set

Picture Contrast : + 31 Brightness : 31 Color : 0 Tint : + 31 Picture Enhancement : Off Color Temperature : Normal Color Temp.Adjust Reset Reset Select Set ReturnOK

Contrast + 31 Next / Prev Adjust Return

Picture Contrast : + 31 Brightness : 31 Color : 0 Tint : + 31 Picture Enhancement : Off Color Temperature : Normal Color Temp. Adjust Reset Reset Select Set ReturnOK

Color Temperature Normal Next/Prev Select Return

Picture Contrast : + 31 Brightness : 31 Color : 0 Tint : + 31 Picture Enhancement : Off Color Temperature : Normal Color Temp.Adjust Reset Reset Select Set ReturnOK

Picture Color Temp. Adjust On Amplitude Red 63 Green 0 Blue 31 Cut Off Red + 31 Green 0 Blue + 31 Reset Reset Select On/Off Return

MENU OK OK

OK

OK

Selected characters

Contrast

Brightness

Color

Tint

Picture Enhancement

Color Temperature

Color Temp. Adjustment

Amplitude

Cut Off

Reset

Narrows the gap between brightness and darkness.

Black is subdued for increased overall darkness.

Darkens colors.

Enhances red and weakens green.

Brighter scenes are decreased in reddish color.

Brighter scenes are decreased in greenish color.

Brighter scenes are decreased in bluish color.

Dark scenes are decreased in reddish color.

Dark scenes are decreased in greenish color.

Dark scenes are decreased in bluish color.

Broadens the gap between brightness and darkness.

Black is set off for increased overall brightness.

Lightens colors.

Enhances green and weakens red.

Brighter scenes are increased in reddish color.

Brighter scenes are increased in greenish color.

Brighter scenes are increased in bluish color.

Dark scenes are increased in reddish color.

Dark scenes are increased in greenish color.

Dark scenes are increased in bluish color.

(Selects the Reset mode)

Setup hint

Adjust for maximum visibility to suit the ambient brightness. Adjust further till [+40] by pressing and holding cursor button at [+31]. The color for [+32] to [+40] numbers will change from white to magenta. This special mode is better for dark scenes. For brighter scene some parts of the picture might not be clear. We recommend to set at [+31]. "Panel Life" in the Function Menu should be set to Normal when Contrast setting is adjusted.

Adjust to taste.

Adjust to taste.

This is not available for adjustment when receiving PAL/SECAM signal. In this case the character will be grayed out. Adjust for the most realistic skin color.

Sets the clarity of small details to the desired level.

Normally set to Normal.

Turn On when you wish to change color temperature to suit user preferences.

Adjust color temperature to suit user preference. These settings are independently stored in each of the 4 Color Temperature modes.

The original factory settings for the items of this Menu page can be restored by pressing the OK button.

Red

Green

Blue

Red

Green

Blue

Off Low Middle High

Cool Normal Warm Black / White

Off On

015_PDM-5520_U_E 12/13/04, 9:24 AM33

34

OPERATING INSTRUCTIONS FOR PC (continued)

AUDIO MENU

TIMER MENU

MENU OK

Picture Audio Timer Function Setup Language Select OK Set

Audio Audio Mode : Movie Treble : + 10 Bass : 10 Balance : 0 L R SRS TruBass : Middle Matrix Surround : Off Perfect Volume : Off Reset Reset Select Set Return

Picture Audio Timer Function Setup Language Select OK Set

Timer Off Timer : 30Min. On Timer : - - : - - Select Adjust Return

MENU OK

Setup hint

Movie: This selects the audio mode suitable for Movies. Music: This selects the audio mode suitable for Music. Speech: This selects the audio mode suitable for News, Talk show etc. Favorite: This mode should be adjusted to suit your preference.

Adjust to taste.

Adjust to taste.

Adjust to taste.

SRS TruBass takes advance of the ability of the human ear to distinguish between two different tones. By using this ability, TruBass gives enhanced bass sound that otherwise would not be heard. Adjust it depending on the users preference.

This features the spacious sound effects of a stadium.

This will automatically adjust volume so each channel and input has the same average volume level.

The original factory settings for the items of this Menu page can be restored by pressing the OK button.

Selected characters

Audio Mode

Treble

Bass

Balance

SRS TruBass

Matrix Surround

Perfect Volume

Reset

Suppresses treble.

Suppresses bass.

Suppresses right-side sound.

Enhances treble.

Enhances bass.

Suppresses left-side sound.

(Selects the Reset mode)

Movie Music Speech Favorite

Off Low Middle High

Off On

Off On

Setup hint

This function automatically sets the power to standby status when the indicated time period has elapsed.

This automatically sets the power from standby to ON when the indicated time period has elapsed. The settable time is 00:00~11:59. Input the required time by SELECT buttons on the remote control.

Selected characters

Off Timer

On Timer (- - : )- - minutes

(- - : )- - minutes

--Min. 30Min. 60Min. 120Min. 90Min.

015_PDM-5520_U_E 12/13/04, 9:24 AM34

35

E N

G L

IS H

Setup hint

This moves the picture around the screen in small amounts, at set intervals, to reduce the panel image retention. Image retention occurs when stationary objects, such as screen logos, leave a slight image visible after they should have disappeared.

This is used to reduce the panel image retention that can occur with stationary pictures by displaying a completely white screen. Select On (continuous operation) or 60 Min. (time limit operation) and press the OK button. Press the MENU or RETURN button on the remote control to return to normal viewing.

This turns the gray sidebars On/Off when watching normal mode screen size area. It is always set to Off when the monitor is powered On. It is recommended to set Black Side Panel to off to reduce the panel image retention.

The original factory settings for the items of this Menu page can be restored by pressing the OK button.

This function suppresses the contrast of the screen regardless of the Contrast setting in the Picture Menu. By this control, power consumption can be reduced or degradation of a panel can be mitigated. The order of power consumption is Extend 2 < Extend 1 < Normal. If the Contrast setting is changed when this item is set to Extend 1 or 2, it will be changed to Normal automatically.

This function displays the Input Signal Screen Display every time the input mode and signal mode are changed. Set to OFF if the Input Signal Screen Display is not needed when switching signals.

Assigns ID Nos. to the monitors so that they can be controlled individually (up to 7 monitors can be controlled).

This function changes each level of RGB signal invert to reduce the panel image retention. When this function is required, select On (continuous operation) or 60Min. (time limit operation) and press the OK button. And press the Menu or Return button to exit.

This function is also provided to prevent image retention. If time is set for this item, the screen changes into a white pattern when the monitor enters power save mode, and continues for the period of setting time.

Normally set to 2.2.

Selected characters

Screen Saver

Screen Wipe

Black Side Panel

Video Power Save

Reset

Panel Life

Mode Display

ID Number

Inverse

Standby White

Gamma

On

On

60 Min.

(Selects the Reset mode)

60 Min.

OPERATING INSTRUCTIONS FOR PC (continued)

FUNCTION MENU

MENU OK

Picture Audio Timer Function Setup Language Select OK Set

Function Screen Saver Off Screen Wipe On 60Min. Black Side Panel Off Video Power Save Off Freeze Mode Split Default Zoom Panoramic Reset Reset Select Set Return

Function Panel Life Normal Mode Display Off ID Number 1 Inverse On 60Min. Standby White Off Gamma 2.2 Reset Reset Select Set Return

Off 5Min. 10Min. 60Min. 40Min. 20Min.

Off On

Normal Extend 1 Extend 2

Off On

1 2 3 4 7 6 5

Off 15Min. 30Min. 120Min. 60Min.

2.2 2.8

21

015_PDM-5520_U_E 12/13/04, 9:24 AM35

36

MENU

OK

OPERATING INSTRUCTIONS FOR PC (continued)

SETUP MENU

OK

OK

Picture Audio Timer Function Setup Language Select OK Set

Setup Auto Adjust Adjust Horizontal Position 0 Vertical Position + 31 Horizontal Clock 20 Clock Phase 10 Reset Reset Select Return Exit

Horizontal Position 0 Next / Prev Adjust Return

Setup Auto Adjust Adjust Horizontal Position 0 Vertical Position + 31 Horizontal Clock 20 Clock Phase 10 Reset Reset Select Return Exit

Clock Phase 10 Next / Prev Adjust Return

Setup Input Level 0.7V Frequency Display Off WVGA Type Off WXGA Mode Off Vertical Filter On Frequency Mode Movie RGB1 DVI-PC RGB2 RGB Select Set Return

Setup hint

Horizontal Position, Vertical Position, Horizontal Clock and Clock Phase are adjusted automatically.

Adjust the horizontal display position. (This function is only for RGB2. It is not available (grayed out) for RGB1.)

Adjust the vertical display position. (This function is only for RGB2. It is not available (grayed out) for RGB1.)

Adjust for maximum character clarity. (This function is only for RGB2. It is not available (grayed out) for RGB1.)

Adjust for clear character visibility. (This function is only for RGB2. It is not available (grayed out) for RGB1.)

The original factory settings for the items of this Menu page can be restored by pressing the OK button. (This is effective only for RGB2.)

Normally set to 0.7 V. If white is found to spread across the screen, set to 1.0 V. (This is effective only for RGB2.)

Set this to Off if the frequency information of the Input Signal Screen Display is not required.

This is only available for W-VGA signal. When it is set to On, the display area mode can be selected Full or Real.

This is only available for W-XGA signal. When it is set to On, the display area mode can be selected Full or Real. (RGB2 (ANALOG) INPUT only)

Turn On when concerned about screen flicker.

Set to Movie when viewing moving images on a personal computer.

Selected characters

Auto Adjust*

Horizontal Position

Vertical Position

Horizontal Clock

Clock Phase

Reset

Input Level

Frequency Display

WVGA Type

WXGA Mode

Vertical Filter

Frequency Mode

RGB1 RGB2

(Menu)

Moves the horizontal position to left.

Moves down the vertical position.

Reduces the dot clock frequency (shrinks the right side).

Slows the dot clock phase (shifts slightly to left).

(Adjust) Press the OK button to start automatic regulation.

Moves the horizontal position to right.

Moves up the vertical position.

Increases the dot clock frequency (expands the right side).

Advances the dot clock phase (shifts slightly to right).

(Selects the Reste mode)

0.7V 1.0V

Off On

Off On

Off On

Movie PC

Off 1280x768 1366x768

* Depending on the type of signal displayed, displays may not be optimized through automatic adjustment. Adjust manually to optimize them.

23

015_PDM-5520_U_E 12/13/04, 9:24 AM36

37

E N

G L

IS H

MENU

OK

OPERATING INSTRUCTIONS FOR PC (continued)

LANGUAGE MENU

OTHER FEATURES FOR PC

Automatic Store

Picture Audio Timer Function Setup Language Select OK Set

Language English Franais Espaol Select Return Exit

Select a language using the SELECT buttons and press the OK button.

Approximately 1 sec. after adjustment is completed, the adjustments will be recorded as shown in the table below.

Menu

Function

Setup

Language

Display

Screen Saver

Screen Wipe

Black Side panel

Panel Life

Mode Display

ID Number

Inverse

Standby White

Gamma

Auto Adjust

Horizontal Position

Vertical Position

Horizontal Clock

Clock Phase

Input Level

Frequensy Display

WVGA Type

Vertical Filter

Frequency Mode

Registration condition

1 setting is registered.

(not registered)

(not registered)

1 setting is registered.

(not registered)

For every signal Mode, 1 setting is registered. (Only for RGB2)

1 setting is registered.

1 setting is registered.

Menu

Picture

Audio

Display

Contrast

Brightness

Color

Tint

Picture Enhancement

Color temperature

Color Temp. Adjust

R Amplitude

G Amplitude

B Amplitude

R Cut Off

G Cut Off

B Cut Off

Audio Mode

Treble

Bass

Balance

SRS TruBass

Matrix Surround

Perfect Volume

Registration condition

For every input function, 1 setting is registered.

For every Color Temperature, 1 setting is registered.

1 setting is registered.

For every Audio Mode, 1 setting is registered.

1 setting is registered.

For every Audio mode, 1 setting is registered.

The previously recorded items will be lost. The signal mode can be identified by the horizontal/vertical sync

frequency and the sync signal polarity. Different signals for which all the elements are the same or similar will be handled as the same signal.

015_PDM-5520_U_E 12/13/04, 9:24 AM37

38

OTHER FEATURES FOR PC (continued)

Signal Check

Power Save Mode

Changes in the signal status are displayed on the screen as they arise.

Status

When Mode Display is set to ON, the input signal is switched or when the RECALL button is pressed.

When the sync signal is no longer detected.

When the input signal does not match the monitor specifications or is in an unstable state.

Display

A guide is displayed for the input terminal and the horizontal and vertical sync frequency.

A guide displays No Sync. Signal, and Power Save (for approx. 5 sec.)

When the condition continues and the sync signal cannot be detected, the indicator lamp of the power source changes in orange and the mode switches to power save mode.

Invalid Scan Freq appears on the display panel.

Action

Recheck the personal computer power switch status and the connection status.

Recheck the input signal specifications.

RGB2 RGB

H : 48.4kHz V : 60.1 Hz

-- -- Min. -- -- : -- --

OFF

! No Sync. Signal

! Invalid Scan Freq.

RGB

43 ~ 45

When the RGB1, RGB2 input is selected When this unit is connected to a VESA DPMS computer, the Power Save (Off) mode can be set to be activated automatically when the

computer is not being used to reduce power consumption by this unit.

Returning to operating status Operate the personal computer, or press either the INPUT SELECT button of the monitor or the RGB1/RGB2 buttons of the remote control to

return the unit to power on mode.

PC signal

Operation mode

Indicating lamp

Power consumption

Active (normal display)

On

Lights green

530W

Blank (no display)

Off

Lights Orange

3W or less (RGB1) 1W or less (RGB2 ; 100V AC 120V) 3W or less (RGB2 ; 120V < AC 240V)

RGB sync signal Horizontal

Vertical

Yes

Yes

No

Yes

Yes

No

No

No

015_PDM-5520_U_E 12/13/04, 9:24 AM38

39

E N

G L

IS H

IMAGE RETENTION OF PLASMA DISPLAY PANEL

Notes

There are different characteristics that result in panel image retention depending on how the plasma monitor is used. Situations and effective usage methods related to ghosting are provided below.

Image retention characteristics of a plasma display panel The image retention phenomenon of a plasma display panel occurs due to partial phosphor degradation arising from partial character and figure display.

For example, when the character image as shown in Fig. A at the right is continuously displayed for a long period of time, the only part of the phosphor (Red, Green, Blue) that will degrade will be the color of the applicable character display portion. Consequently, when a white image is displayed on the entire screen as shown in Fig. A, the character marks displayed up to that time will become a color difference visible to the eye, but the phosphor will never burn.

The degree of image retention is proportional to the brightness of the characters and figures displayed as well as the display time.

The tendency of the phosphor is to degrade more the brighter the characters and figures are displayed. When images of figures with different levels of brightness, as shown in Fig. B, are continuously displayed for a long period of time, it becomes easier for image marks at locations when the brighter figures are displayed to be noticeable.

* The image retention images in this document are exaggerated for the purpose of explanation. The actual manner in which the image retention is seen differs depending on the operation time and brightness.

Methods to Reduce the Occurrence of Image Retention

Lower the Contrast and Brightness settings of the plasma display panel as much as possible. A function is provided in the display that allows you to control the brightness of the screen to reduce degradation of the panel. Using this function makes it possible to reduce image retention. (Refer to Panel Life (Extend 1 or Extend 2 shown on )

Set the plasma monitor to an Screen Wipe or Inverse display. The occurrence of image retention when displaying images of identical patterns, such as static images, for long periods of time can be reduced by displaying a reversed color or completely white screen for about 1 ~ 2 hours after terminating the display. (Settings can be made using Screen Wipe and Inverse of Function MENU shown on )

Using in combination with moving images Since the degradation of the fluorescent material progresses comparatively uniformly for moving images, the occurrence of partial image retention can be controlled. We recommend using the plasma monitor in combination with moving images such as those of DVD playback. * Please be careful since image retention will occur if display is left in a two screen display state for a long period of time. * Television broadcasts include images displayed for long periods of time in which the left and right or top and bottom of the image are cut

and broadcast station name or time are displayed for a long period of time at the same portion of the screen. Image retention in these portions can be expected to occur, so please be aware.

35

35

About screen defects High precision technology is used in the making of plasma display panel but there may be dark spots (points that do not illuminate) and

bright spots (points that are too bright) in some cases. These do not indicate a malfunction.

About residual images In some cases, residual images may remain after the short-term display of still images and another image is displayed, but these will

disappear and return to normalcy. This is not a malfunction.

About the panel screen Plasma display panels display images by means of electrical discharges inside the panel. Because of this, the temperature of the panel

surface may rise in some cases. Also, plasma display panels are made of finely processed glass. A reinforced glass filter is installed over the panel surface but avoid strong impact because there is still danger of glass breakage.

015_PDM-5520_U_E 12/13/04, 9:24 AM39

40

TROUBLESHOOTING FOR PC

Symptoms That Appear to be Failures Make the checkes suggested below dpending on the symptoms observed. If the symptoms remain uncorrected, contact your dealer.

CAUTION Customer servicing can be hazardous.

No picture with the power-indicating lamp off.

The message No Sync. Signal or Power Save is displayed.

No picture, with the power indicating lamp lit orange.

The message Invalid Scan Freq. is displayed.

The power indicating lamp is lit normally but no picture displays.

The display image appears flowing slantwise.

Text displayed across the screen appears vertically streaked, with the characters in vertical columns blurred.

Text displayed across the screen appears blurred.

A fine pattern flickers when displayed on the screen.

The remote control does not work.

Check the way the power cable is connected. Press the power switch.

No sync signal is detected. Check the way the signal cable is connected. Make sure that the switch of the computer, imaging

equipment, etc., is turned on. Make sure the computer is not in the power-save mode. Check to see if the input selection matches the connection

terminal.

An input signal is not received normally. Check to see if the input signal matches the monitor

specifications. Check the way the signal cable is connected.

Check the contrast and brightness settings (adjust them for higher contrast and brightness).

Check the way the signal cable is connected.

Adjust the dot clock frequency and phase. (Adjust the dot clock frequency first, the dot clock phase next.) (RGB input)

Adjust the dot clock phase for the clearest viewing. (RGB input)

Check to see if the batteries are loaded in the remote control in opposite direction.

Check to see if the batteries in the remote control are OK. Check if the setting of remote control ID no. is correct.

Symptom Point to check See page

! No Sync. Signal

! Invalid Scan Freq.

28

29

27

27

44

45

27

33

36

42

36

42

11

32

015_PDM-5520_U_E 12/13/04, 9:24 AM40

41

E N

G L

IS H

TROUBLESHOOTING FOR PC (continued)

Symptoms That Appear to be Failures (continued)

See pagePoint to checkSymptom

The temperature of the display panel surface is high.

There are points (*) on the screen that differ in color from the periphery of the screen. * Points that do not light, points with brightness different from that of the periphery, points with color different from that of the periphery, etc.

Vertical stripes appear, depending on the screen contents.

Coarse horizontal stripes appear in FULL display.

Flickering in the form of horizontal lines oscillating up and down. (PC INPUT MODE only)

The top of the monitor heats up.

Text characters are displayed with varying thicknesses.

Plasma display panel is lighting the phosphors in the display panel by the discharge of internal radiation. In some cases, this may cause the temperature of the panel surface to increase. Please note that this is not a malfunction.

High-precision technology is used to manufacture the plasma display panel, However in some cases, there are minor defects in some parts of the screen. Please note that this is not a malfunction.

The plasma display panel is lighting the phosphors by the discharge of internal radiation. Depending on the screen contents, in rare cases this may cause vertical stripes to appear because of failure to light. Please note that this is not a malfunction.

Adjusting the Clock Phase will reduce the horizontal stripes. (RGB input)

If the direct frequency from the computer is below 85Hz, try a higher frequency (upper limit 85Hz). There may be a slight attenuation of the current image.

Try turning the Vertical Filter On. For this case however, the vertical resolution will drop.

When used for long periods of time, the top of the monitor may heat up. This is not a malfunction.

The thicknesses of characters and lines may vary if images with a vertical resolution greater than 768 lines are displayed; however, this is not a malfunction.

36

36

-

-

-

-

-

015_PDM-5520_U_E 12/13/04, 9:24 AM41

42

TROUBLESHOOTING FOR PC (continued)

Actions to Correct Abnormal Displays

Depending on the kind of system equipment used, images may not be displayed normally. In this case, make the adjustments suggested below. (only for RGB2)

Symptom 1

Example

Adjustment procedure

Text displayed across the screen appears vertically streaked, with some characters blurred (figure 1). The display image appears flowing (figure 2) (RGB input).

Figure 1

1) Press the AUTO button on the remote control.

When adjustment is not possible with Auto Adjust 2) Press the MENU button. The Main Menu will be displayed. 3) Press the SELECT button and select Setup. 4) Press the OK button. The Setup Menu will be displayed. 5) Press the SELECT button and select Horizontal Clock. (Display fine patterns as characters or a vertical striped pattern over the entire screen during Horizontal Clock adjustment.) 6) Press the or ADJUST buttons and search for clear characters over the entire screen. 7) Perform adjustment for symptom 2 below, when the characters are blurred on the entire screen.

Symptom 2

Example

Adjustment procedure

Text displayed across the screen appears blurred in its entirety (figure 2). A fine pattern flickers when displayed on the screen (figure 3).

Figure 2 Figure 3

1) Press the AUTO button on the remote control.

When adjustment is not possible with Auto Adjust 2) Press the MENU button. The Main Menu will be displayed. 3) Press the SELECT button and select Setup. 4) Press the OK button. The Setup Menu will be displayed. 5) Press the SELECT button and select Clock Phase. (Display fine patterns as characters or a vertical striped pattern over the entire screen during Clock Phase adjustment.)

The display image may be momentarily disturbed during clock adjustment but this is not a failure.

6) Press or ADJUST buttons to make the text appear clean across the screen.

6) Press or ADJUST buttons to make the text appear without flickering.

ABC

B ABCDEFGHIJ

abcdefgABCDEFGabcd

ABCDEFGHIJ

abcdefgABCDEFGabcd

Vertical streaks

Before adjustment Some characters are blurred.

After adjustment All characters appear crisp now.

After adjustment All characters are blurred.

A C ABC

ABCDEFGHIJ

abcdefgABCDEFGabcd

ABCDEFGHIJ

abcdefgABCDEFGabcd

Before adjustment

After adjustment

ABC

ABC

Before adjustment

After adjustment

015_PDM-5520_U_E 12/13/04, 9:24 AM42

43

E N

G L

IS H

When different kinds of input signals are simultaneously input to the monitor via a graphics board or the like, the monitor will automatically select the signals in the following priority order:

*Even in the case of the recommended signals shown on the following page, there may be instances when correct display is not possible. In this case, use H/V separate sync, H/V composite sync.

PRODUCT SPECIFICATIONS FOR PC

Signal Input

Product specifications and designs are subject to change without notice.

The monitor takes at least 30 minutes to attain optimal picture quality.

RGB terminal (D-sub 15-pin connector)

Panel

Net dimensions (excluding pedestal)

Net weight (excluding pedestal)

Ambient conditions

Power supply

Power consumption/at standby

Audio output

(RGB input)

Input signals

Recommended signal

Approx. 55 inches (1229 (H) x 691 (V) mm, diagonal 1410mm)

1366 (H) x 768 (V) pixels

1394 (W) x 857 (H) x 105 (D) mm

63.5kg

Operating : 5C to 35C, Storage : 0C to 40C

Operating : 20% to 80%, Storage : 20% to 90% (non-condensing)

AC100 - 240V, 50/60Hz

530W / <3W

12W + 12W (6 ), sub woofer (RCA)

RGB1 DVI input terminal (DVI-D) RGB1 audio input terminal (3.5mm Stereo Mini Jack) RGB2 analog RGB input terminal (D-sub 15-pin) RGB2 audio input terminal (3.5mm Stereo Mini Jack)

0.7 V/1.0 Vp-p, analog RGB (Recommended Signal)

H/V separate, TTL level [2K ] H/V composite, TTL level [2K ] Sync on green, 0.3 Vp-p [75 ]

44 modes

Display dimensions

Resolution

Temperature

Relative humidity

Input terminals

Video signals

Sync signals

Pin

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

Input signal

R

G or sync on green

B

No connection

No connection

R.GND

G.GND

B.GND

No connection

GND

No connection

[SDA]

H. sync or H/V composite sync

V. sync. [V.CLK]

[SCL]

Sync signal type

H/V seperate sync.

H/V composite sync.

sync. on Green *

Priority

1

2

3

44 45

1

67890

-=~!@

2345

015_PDM-5520_U_E 12/13/04, 9:24 AM43

44

PRODUCT SPECIFICATIONS FOR PC (continued)

Recommended Signal List

Signal Input (continued) DVI terminal (DVI-D)

Pin

1

2

3

4

5

6

7

8

9

10

11

12

13

Input signal

T.M.D.S. Data2-

T.M.D.S. Data2+

T.M.D.S. Data2/4 Shield

T.M.D.S. Data4-

T.M.D.S. Data4+

DDC Clock

DDC Data

No Connect

T.M.D.S. Data1-

T.M.D.S. Data1+

T.M.D.S. Data1/3 Shied

T.M.D.S. Data3-

T.M.D.S. Data3+

Pin

14

15

16

17

18

19

20

21

22

23

24

Frame

Input signal

+5 Power

Ground (for+5V)

Hot Plug Detect

T.M.D.S. Data0-

T.M.D.S. Data0+

T.M.D.S. Data0/5 Shield

T.M.D.S. Data5-

T.M.D.S. Data5+

T.M.D.S. Clock Shield

T.M.D.S. Clock+

T.M.D.S. Clock-

GND

With Digital RGB signal input (RGB1 input)

Make sure that the signal of the equipment to be connected is compatible with the specifications on this list.

Resolution

640 X 400

640 X 480

864 X 480

640 X 480

640 X 480

640 X 480

800 X 600

800 X 600

800 X 600

800 X 600

800 X 600

1024 X 768

1024 X 768

1024 X 768

Vertical frequency (Hz)

70.08

59.94

59.94

72.81

75.00

85.01

56.25

60.32

72.19

75.00

85.06

60.00

70.07

75.03

Horizontal frequency (kHz)

31.47

31.47

31.47

37.86

37.50

43.27

35.16

37.88

48.08

46.88

53.67

48.36

56.48

60.02

Dot clock frequency (MHz)

25.18

25.18

34.24

31.50

31.50

36.00

36.00

40.00

50.00

49.50

56.25

65.00

75.00

78.75

No.

1

2

3

4

5

6

7

8

9

10

11

12

13

14

Signal Name

VGA

W-VGA

VESA

Remarks

WVGA type : On

Signal Mode

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

17 18 19 20 21 22 23 24

015_PDM-5520_U_E 12/13/04, 9:24 AM44

45

E N

G L

IS H

Remarks

WVGA type : On

WXGA Mode: (1280 x 768)

WXGA Mode: (1366 X 768)

PRODUCT SPECIFICATIONS FOR PC (continued)

Recommended Signal List (continued)

With Analog RGB signal input (RGB2 input)

The type of video board or connecting cable used may not allow for correct display adjustment of Horizontal Position, Vertical Position, Horizontal Clock and Clock Phase.

The monitor may fail to display an animation image correctly when a signal having a vertical frequency of 85Hz or higher is input to it. The monitor differentiates signal modes according to the horizontal and vertical frequencies and the horizontal and vertical sync signal

polarities. Note that different signals having all these elements alike may be handled as the same signal. Displaying images with more than 768 lines of vertical resolution at Full diplay (compressed display) can result in the interpolation of stripes.

No.

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

Signal Name

VGA

W-VGA

VESA

Macintosh

W-XGA

W-XGA

Resolution

640 X 400

640 X 480

864 X 480

640 X 480

640 X 480

640 X 480

800 X 600

800 X 600

800 X 600

800 X 600

800 X 600

1024 X 768

1024 X 768

1024 X 768

1024 X 768

1152 x 864

1280 x 1024

1280 x 1024

1280 x 1024

1600 x 1200

1600 x 1200

1600 x 1200

640 x 480

832 x 624

1024 x 768

1152 x 870

1280 x 768

1280 x 768

1280 x 768

1366 x 768

Vertical frequency (Hz)

70.08

59.94

59.94

72.81

75.00

85.01

56.25

60.32

72.19

75.00

85.06

60.00

70.07

75.03

85.00

75.00

60.02

75.03

85.02

60.00

75.00

85.00

66.67

74.55

74.93

75.06

59.833

69.997

59.876

60.015

Horizontal frequency (kHz)

31.47

31.47

31.47

37.86

37.50

43.27

35.16

37.88

48.08

46.88

53.67

48.36

56.48

60.02

68.68

67.50

63.98

79.98

91.15

75.00

93.75

106.25

35.00

49.72

60.24

68.68

47.986

56.137

47.776

47.712

Dot clock frequency (MHz)

25.18

25.18

34.24

31.50

31.50

36.00

36.00

40.00

50.00

49.50

56.25

65.00

75.00

78.75

94.50

108.00

108.00

135.00

157.50

162.00

202.50

229.50

30.24

57.28

80.00

100.00

81.00

94.760

79.50

85.50

Signal Mode

015_PDM-5520_U_E 12/13/04, 9:24 AM45

20 18 16 14 12 10 8 6 4 2

21 19 17 15 13 11 9 7 5 3 1

20 18 16 14 12 10 8 6 4 2

21 19 17 15 13 11 9 7 5 3 1

DVD player

Sat/Cable box

VCR

AV receiver

Video camera

S video cable

Audio pin cable

Video pin cable

S video cable

Component video cable

Video pin cable

Video pin cable

Audio pin cable

Audio pin cable

S video cable

S video cable

Component video cable

Component video cable

Video pin cable

Audio pin cable

S video cable

Component video cable

Surround back left speaker

Presence left

speaker

Surround left

speaker

Front left

speaker

Center speaker

Subwoofer Front right

speaker

Surround right

speaker

Presence right

speaker

Surround back right speaker

(612W)

(612W)

PDM-5520 Monitor rear panel

U.S.

To AC outlet

PHONODVR

STANDBY /ON

PURE DIRECT

2CH/MULTI CH SPEAKERS

VIDEO AUX

REC OUT/ZONE 2 INPUT MODESOURCE/REMOTE

DVDDTV/LD MD/TAPE

CD-R

TUNER

CD

VIDEO AUX

VCR 2

VCR 1

SAT

CABLE

A B

STRAIGHT

EFFECT

MULTI CH INPUT

DSP PROGRAM BALANCE

TONE CONTROL

VOLUME

INPUT SELECTOR

MULTI JOG

SILENT OPTIMIZER MIC

PHONES OPTICALRAUDIOLVIDEOS VIDEO

TUNING MODE FM/AMMEMORY PRESET /TUNING

IN

OUT

COMPONENT VIDEO

PB/BPR/RY/G

S VIDEO VIDEO

MONITOR OUT

Basic connection to an AV Receiver

NOTE: When this plasma monitor receives signals through both S VIDEO and VIDEO terminals, signals input through the S VIDEO terminal have priority.

All cables listed are sold separately.

2004 All rights reserved.

Printed in Japan QT45541 A

PDM-5520 High Definition Plasma monitor

Connection Guide

Connection_U_PDM-5520 11/25/04, 11:03 AM1

Examples of Image Retention Exemples de Rtention dImage

English Image Retention Image Retention can be an issue for all plasma monitors, however if you follow the simple guidelines listed below, you can enjoy many years of viewing. YAMAHA has included a number of features in our range of plasma monitors which help to reduce image retention. Please refer to the user manual for this model for instruction on how to use these features.

* Ensure screen save mode is activated. * Always display the image in a mode that fills the screen. * Avoid using split screen modes for long periods of time. * Do not allow the On Screen Display to stay on for long periods of time. * Do not display still images, such as menus from game consoles, Teletext, PCs or logos on the monitor for long periods

of time. * We recommend that you reduce Contrast and Brightness levels as much as possible.

Franais Rtention dimage La rtention peut tre un problme pour les crans Plasma, nanmoins si vous suivez les simples instructions suivantes, vous pourrez profiter de votre crans pendant de longues annes. YAMAHA a pourvu ses crans moniteurs plasma de fonctions permettant de rduire la rtention dimage. Veuillez sil vous plat vrifier dans le mode demploi de ce modle comment utiliser ces fonctions.

* Assurez vous que lconomiseur dcran est bien activ. * Vrifiez toujours que le format dimage que vous utilisez est constamment adapt lcran. * Evitez dutiliser le mode de sparation

Manualsnet FAQs

If you want to find out how the PDM-5520 Yamaha works, you can view and download the Yamaha PDM-5520 Monitor User's Manual on the Manualsnet website.

Yes, we have the User's Manual for Yamaha PDM-5520 as well as other Yamaha manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The User's Manual should include all the details that are needed to use a Yamaha PDM-5520. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Yamaha PDM-5520 Monitor User's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Yamaha PDM-5520 Monitor User's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Yamaha PDM-5520 Monitor User's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Yamaha PDM-5520 Monitor User's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Yamaha PDM-5520 Monitor User's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.