Contents

Yamaha DTX-PROX Module Owner's Manual PDF

1 of 68
1 of 68

Summary of Content for Yamaha DTX-PROX Module Owner's Manual PDF

Owners Manual

Drum Trigger Module

EN

Contents

Specifications

page 9

page 60

Features of the DTX-PROX page 8

S

-1 DTX-PROX Owners Manual

This product utilizes batteries or an external power supply (adapter). DO NOT connect this product to any power supply or adapter other than one described in the manual, on the name plate, or specifically recommended by Yamaha.

WARNING: Do not place this product in a position where anyone could walk on, trip over, or roll anything over power or connecting cords of any kind. The use of an extension cord is not recommended! If you must use an extension cord, the minimum wire size for a 25 cord (or less ) is 18 AWG. NOTE: The smaller the AWG number, the larger the current handling capacity. For longer extension cords, con- sult a local electrician.

This product should be used only with the components supplied or; a cart, rack, or stand that is recommended by Yamaha. If a cart, etc., is used, please observe all safety markings and instructions that accom- pany the accessory product.

SPECIFICATIONS SUBJECT TO CHANGE: The information contained in this manual is believed to be correct at the time of printing. However, Yamaha reserves the right to change or modify any of the specifications without notice or obligation to update existing units.

This product, either alone or in combination with an amplifier and headphones or speaker/s, may be capable of producing sound levels that could cause permanent hearing loss. DO NOT operate for long periods of time at a high volume level or at a level that is uncomfort- able. If you experience any hearing loss or ringing in the ears, you should consult an audiologist. IMPORTANT: The louder the sound, the shorter the time period before damage occurs.

NOTICE: Service charges incurred due to a lack of knowledge relating to how a function or effect works (when the unit is operating as designed) are not covered by the manufacturers warranty, and are therefore the owners responsibility. Please study this manual carefully and consult your dealer before requesting service.

ENVIRONMENTAL ISSUES: Yamaha strives to produce products that are both user safe and envi- ronmentally friendly. We sincerely believe that our products and the production methods used to produce them, meet these goals. In keep- ing with both the letter and the spirit of the law, we want you to be aware of the following:

Battery Notice: This product MAY contain a small non-rechargeable battery which (if applicable) is soldered in place. The average life span of this type of battery is approximately five years. When replacement becomes nec- essary, contact a qualified service representative to perform the replacement.

This product may also use household type batteries. Some of these may be rechargeable. Make sure that the battery being charged is a rechargeable type and that the charger is intended for the battery being charged.

When installing batteries, never mix old batteries with new ones, and never mix different types of batteries. Batteries MUST be installed cor- rectly. Mismatches or incorrect installation may result in overheating and battery case rupture.

Warning: Do not attempt to disassemble, or incinerate any battery. Keep all bat- teries away from children. Dispose of used batteries promptly and as regulated by the laws in your area. Note: Check with any retailer of household type batteries in your area for battery disposal information.

Disposal Notice: Should this product become damaged beyond repair, or for some rea- son its useful life is considered to be at an end, please observe all local, state, and federal regulations that relate to the disposal of prod- ucts that contain lead, batteries, plastics, etc. If your dealer is unable to assist you, please contact Yamaha directly.

NAME PLATE LOCATION: The name plate is located on the bottom of the product. The model number, serial number, power requirements, etc., are located on this plate. You should record the model number, serial number, and the date of purchase in the spaces provided below and retain this manual as a permanent record of your purchase.

Model

Serial No.

Purchase Date

PLEASE KEEP THIS MANUAL

SPECIAL MESSAGE SECTION

92-BP (bottom)

COMPLIANCE INFORMATION STATEMENT (Suppliers declaration of conformity procedure)

Responsible Party : Yamaha Corporation of America Address : 6600 Orangethorpe Ave., Buena Park, Calif. 90620

Telephone : 714-522-9011 Type of Equipment : Drum Trigger Module

Model Name : DTX-PROX

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this device may not cause harmful interference, and 2) this device must accept any interference received including interference that may cause undesired operation.

* This applies only to products distributed by Yamaha Corporation of America. (FCC SDoC)

(can_b_02)

CAN ICES-3 (B)/NMB-3(B)

S-2DTX-PROX Owners Manual

1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT! This product, when installed as indicated in the instructions con- tained in this manual, meets FCC requirements. Modifications not expressly approved by Yamaha may void your authority, granted by the FCC, to use the product.

2. IMPORTANT: When connecting this product to accessories and/ or another product use only high quality shielded cables. Cable/s supplied with this product MUST be used. Follow all installation instructions. Failure to follow instructions could void your FCC authorization to use this product in the USA.

3. NOTE: This product has been tested and found to comply with the requirements listed in FCC Regulations, Part 15 for Class B digital devices. Compliance with these requirements provides a reason- able level of assurance that your use of this product in a residential environment will not result in harmful interference with other elec- tronic devices. This equipment generates/uses radio frequencies and, if not installed and used according to the instructions found in the users manual, may cause interference harmful to the operation of other electronic devices. Compliance with FCC regulations does

not guarantee that interference will not occur in all installations. If this product is found to be the source of interference, which can be determined by turning the unit OFF and ON, please try to elimi- nate the problem by using one of the following measures:

Relocate either this product or the device that is being affected by the interference.

Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install AC line filter/s.

In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in is 300 ohm ribbon lead, change the lead-in to co-axial type cable.

If these corrective measures do not produce satisfactory results, please contact the local retailer authorized to distribute this type of product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service Division, 6600 Orangethorpe Ave, Buena Park, CA90620

The above statements apply ONLY to those products distributed by Yamaha Corporation of America or its subsidiaries.

* This applies only to products distributed by Yamaha Corporation of America. (class B)

FCC INFORMATION (U.S.A.)

S

-3 DTX-PROX Owners Manual

For AC adaptor

The above warning is located on the bottom of the unit.

Explanation of Graphical Symbols The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of suffi- cient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral trian- gle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

IMPORTANT SAFETY INSTRUCTIONS 1 Read these instructions. 2 Keep these instructions. 3 Heed all warnings. 4 Follow all instructions. 5 Do not use this apparatus near water. 6 Clean only with dry cloth. 7 Do not block any ventilation openings. Install in accor-

dance with the manufacturers instructions. 8 Do not install near any heat sources such as radiators, heat

registers, stoves, or other apparatus (including amplifiers) that produce heat.

9 Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10 Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11 Only use attachments/accessories specified by the manu- facturer.

12 Use only with the cart, stand, tri- pod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination to avoid injury from tip-over.

13 Unplug this apparatus during light- ning storms or when unused for long periods of time.

14 Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped

(UL60065_03)

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO

QUALIFIED SERVICE PERSONNEL.

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN

WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE.

S-4DTX-PROX Owners Manual

(bottom_en_01)

(weee_eu_en_02)

The model number, serial number, power requirements, etc., may be found on or near the name plate, which is at the bottom of the unit. You should note this serial number in the space provided below and retain this manual as a permanent record of your purchase to aid identification in the event of theft.

Model No.

Serial No.

Information for users on collection and disposal of old equipment: This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in accordance with your national legislation.

By disposing of these products correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling.

For more information about collection and recycling of old products, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items.

For business users in the European Union: If you wish to discard electrical and electronic equipment, please contact your dealer or supplier for further information.

Information on Disposal in other Countries outside the European Union: This symbol is only valid in the European Union. If you wish to discard these items, please contact your local authorities or dealer and ask for the correct method of disposal.

2 DTX-PROX Owners Manual

PRECAUTIONS PLEASE READ CAREFULLY BEFORE PROCEEDING

Please keep this manual in a safe and handy place for future reference.

WARNING This AC adaptor is designed for use with only Yamaha electronic instruments.

Do not use for any other purpose.

Indoor use only. Do not use in any wet environments.

CAUTION When setting up, make sure that the AC outlet is easily accessible. If some

trouble or malfunction occurs, immediately turn off the power switch of the instrument and disconnect the AC adaptor from the outlet. When the AC adaptor is connected to the AC outlet, keep in mind that electricity is flowing at the minimum level, even if the power switch is turned off. When you are not using the instrument for a long time, make sure to unplug the power cord from the wall AC outlet.

WARNING Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:

Do not place the power cord near heat sources such as heaters or radiators. Also, do not excessively bend or otherwise damage the cord, or place heavy objects on it.

Only use the voltage specified as correct for the instrument. The required voltage is printed on the name plate of the instrument.

Use the specified adaptor (page 60) only. Using the wrong adaptor can result in damage to the instrument or overheating.

Check the electric plug periodically and remove any dirt or dust which may have accumulated on it.

This instrument contains no user-serviceable parts. Do not open the instrument or attempt to disassemble or modify the internal components in any way. If it should appear to be malfunctioning, discontinue use immediately and have it inspected by qualified Yamaha service personnel.

Do not expose the instrument to rain, use it near water or in damp or wet conditions, or place on it any containers (such as vases, bottles or glasses) containing liquids which might spill into any openings. If any liquid such as water seeps into the instrument, turn off the power immediately and unplug the power cord from the AC outlet. Then have the instrument inspected by qualified Yamaha service personnel.

Never insert or remove an electric plug with wet hands.

Do not put burning items, such as candles, on the unit. A burning item may fall over and cause a fire.

Radio waves or magnetism may affect electro-medical devices. - Do not use this product near medical devices or inside areas in which the

use of radio waves is restricted. - Do not use this product within 15cm (6 in.) of persons with a heart

pacemaker or defibrillator implant.

When one of the following problems occur, immediately turn off the power switch and disconnect the electric plug from the outlet. Then have the device inspected by Yamaha service personnel. - The power cord or plug becomes frayed or damaged. - It emits unusual smells or smoke. - Some object has been dropped into the instrument. - There is a sudden loss of sound during use of the instrument. - If any cracks or breakages exist on the instrument.

For the AC adaptor

For DTX-PROX

Power supply/AC adaptor

Do not open

Water warning

Fire warning

Influences on electro-medical devices

If you notice any abnormality

DMI-7 1/2

3DTX-PROX Owners Manual

CAUTION Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage to the instrument or other property. These precautions include, but are not limited to, the following:

Do not connect the instrument to an electrical outlet using a multiple- connector. Doing so can result in lower sound quality, or possibly cause overheating in the outlet.

When removing the electric plug from the instrument or an outlet, always hold the plug itself and not the cord. Pulling by the cord can damage it.

Remove the electric plug from the outlet when the instrument is not to be used for extended periods of time, or during electrical storms.

Assemble the instrument in the proper sequence by following the assembly instructions in this manual. Also, make sure to tighten the bolts regularly. Failure to do so might result in damage to the instrument or even injury.

Do not place the instrument in an unstable position where it might accidentally fall over.

Before moving the instrument, remove all connected cables, to prevent damage to the cables or injury to anyone who might trip over them.

When setting up the product, make sure that the AC outlet you are using is easily accessible. If some trouble or malfunction occurs, immediately turn off the power switch and disconnect the plug from the outlet. Even when the power switch is turned off, electricity is still flowing to the product at the minimum level. When you are not using the product for a long time, make sure to unplug the power cord from the wall AC outlet.

Use the included module holder if you are installing the DTX-PROX on the drum hardware. Also, make sure you use the wing bolts included with the module holder. Failure to do so could cause damage to the internal components or result in the instrument falling over.

Take care when setting up cables. If anyone were to trip on a cable, the instrument could topple over and cause injury.

Before connecting the instrument to other electronic components, turn off the power for all components. Before turning the power on or off for all components, set all volume levels to minimum.

Be sure to set the volumes of all components at their minimum levels and gradually raise the volume controls while playing the instrument to set the desired listening level.

Do not insert a finger or hand in any gaps on the instrument.

Never insert or drop paper, metallic, or other objects into the gaps on the panel. This could cause physical injury to you or others, damage to the instrument or other property, or operational failure.

Do not rest your weight on, or place heavy objects on the instrument, and do not use excessive force on the buttons, switches or connectors.

Keep small parts out of the reach of infants. Your children may accidentally swallow them.

Do not use the instrument/device or headphones for a long period of time at a high or uncomfortable volume level, since this can cause permanent hearing loss. If you experience any hearing loss or ringing in the ears, consult a physician.

Always turn the power off when the instrument is not in use.

Even when the [ ] (Standby/On) switch is in standby status (display is off), electricity is still flowing to the instrument at the minimum level.

When you are not using the instrument for a long time, make sure you unplug the power cord from the wall AC outlet.

Power supply/AC adaptor

Assembly

Location

Connections

Handling caution

Yamaha cannot be held responsible for damage caused by improper use or modifications to the instrument, or data that is lost or destroyed.

DMI-7 2/2

4 DTX-PROX Owners Manual

NOTICE To avoid the possibility of malfunction/ damage to the product, damage to data, or damage to other property, follow the notices below.

Handling Do not use the instrument in the vicinity of a TV, radio, stereo equip-

ment, mobile phone, or other electric devices. Otherwise, the instrument, TV, or radio may generate noise. When you use the instrument along with an application on your smart device such as a smartphone or tablet, we recommend that you set Wi-Fi or Bluetooth to on after setting Airplane Mode to on on that device in order to avoid noise caused by communication.

Do not expose the instrument to excessive dust or vibrations, or extreme cold or heat (such as in direct sunlight, near a heater, or in a car during the day) to prevent the possibility of panel disfiguration, damage to the internal components or unstable operation.

Do not place vinyl, plastic or rubber objects on the instrument, since this might discolor the panel.

Maintenance When cleaning the instrument, use a soft and dry/slightly damp

cloth. Do not use paint thinners, solvents, alcohol, cleaning fluids, or chemical-impregnated wiping cloths.

Saving data System settings (Reference Manual (PDF)) are retained when the

power is turned off. However, the saved data may be lost due to some failure, an operation mistake, etc. Save your important data onto USB flash drive/an external device such as a computer (Refer- ence Manual (PDF)). Before using a USB flash drive, make sure to refer to page 21.

Edited Kit/Click, etc. are lost when you turn off the power to the instrument. This also occurs when the power is turned off by the Auto Power Off function (page 19). Save the data to the instrument, or to USB flash drive/an external device such as a computer (Refer- ence Manual (PDF)). However, the data saved to the instrument may be lost due to some failure, an operation mistake, etc. Save your important data onto USB flash drive/an external device such as a computer (Reference Manual (PDF)). Before using a USB flash drive, make sure to refer to page 21.

To protect against data loss through USB flash drive damage, we recommend that you save your important data onto spare USB flash drive or an external device such as a computer as backup data.

About Bluetooth Bluetooth is a technology for wireless communication between devices within an area of about 10 meters (33 ft.) employing the 2.4 GHz fre- quency band.

Handling Bluetooth communications The 2.4 GHz band used by Bluetooth compatible devices is a radio

band shared by many types of equipment. While Bluetooth compat- ible devices use a technology minimizing the influence of other components using the same radio band, such influence may reduce the speed or distance of communications and in some cases interrupt communications.

The speed of signal transfer and the distance at which communica- tion is possible differs according to the distance between the com- municating devices, the presence of obstacles, radio wave conditions and the type of equipment.

Yamaha does not guarantee all wireless connections between this unit and devices compatible with Bluetooth function.

Information About copyrights

Copying of the commercially available musical data including but not limited to MIDI data and/or audio data is strictly prohibited except for your personal use.

This product incorporates and bundles contents in which Yamaha owns copyrights or with respect to which Yamaha has license to use others copyrights. Due to copyright laws and other relevant laws, you are NOT allowed to distribute media in which these contents are saved or recorded and remain virtually the same or very similar to those in the product.

* The contents described above include a computer program, Accompani- ment Style data, MIDI data, WAVE data, voice recording data, a score, score data, etc.

* You are allowed to distribute medium in which your performance or music production using these contents is recorded, and the permission of Yamaha Corporation is not required in such cases.

About this manual The illustrations and LCD screens as shown in this manual are for

instructional purposes only, and may appear somewhat different from those on your instrument.

Windows is a registered trademark of Microsoft Corporation in the United States and other countries.

Apple, Mac, Macintosh, iPhone, iPad, iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries.

Android is a trademark of Google LLC. The Bluetooth word mark and logos are registered trademarks

owned by Bluetooth SIG, Inc. and any use of such marks by Yamaha Corporation is under license.

The company names and product names in this manual are the trademarks or registered trademarks of their respective companies.

The names of buttons, terminals, and the like from the DTX-PROXs front, rear and top panels are enclosed in [ ] (square brackets).

Latest Firmware Version From time to time, Yamaha may update product firmware without prior notice. We recommend, therefore, that you check our web site (below) for the latest version and keep your DTX-PROX firmware up to date.

https://download.yamaha.com/

The content of this Owners Manual applies to the newest version of the firmware as of printing. Details regarding any functions added to later versions will also be made available via the above web site.

About the Electronic Drum Pads (Pads) Within this Owners Manual, the optional external pads that may be connected to the DTX-PROX are referred to by model name. Please note that these model names were up-to-date as of printing of this manual. Details regarding any subsequently released models will be made available via the following web site.

https://download.yamaha.com/

* Yamaha Corporation reserves the right to modify this URL at any time without prior notice.

5DTX-PROX Owners Manual

Importer: Yamaha Music Europe GmbH Siemensstrasse 22-34, 25462 Rellingen, Germany

This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment has very low levels of RF energy that is deemed to comply without testing of specific absorption rate (SAR).

This equipment complies with IC radiation exposure limits set forth for an uncon- trolled environment and meets RSS-102 of the IC radio frequency (RF) Expo- sure rules. This equipment has very low levels of RF energy that is deemed to comply without testing of specific absorption rate (SAR).

This device complies with Industry Canadas licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may

cause undesired operation of the device.

EN SIMPLIFIED EU DECLARATION OF CONFORMITY / SIMPLIFIED UK DECLARATION OF CONFORMITY Hereby, Yamaha Music Europe GmbH declares that the radio equipment type [DTX-PROX] is in compliance with Directive 2014/53/EU and the radio equip- ment regulations of UK. The full texts of the EU declaration of conformity and the UK declaration of conformity are available at the following internet address: https://europe.yamaha.com/en/support/compliance/doc.html

FR DECLARATION UE DE CONFORMITE SIMPLIFIEE Le soussign, Yamaha Music Europe GmbH, dclare que l'quipement radiolectrique du type [DTX-PROX] est conforme la directive 2014/53/ UE. Le texte complet de la dclaration UE de conformit est disponible l'adresse internet suivante: https://europe.yamaha.com/en/support/compliance/doc.html

DE VEREINFACHTE EU-KONFORMITTSERKLRUNG Hiermit erklrt Yamaha Music Europe GmbH, dass der Funkanlagentyp [DTX-PROX] der Richtlinie 2014/53/EU entspricht. Der vollstndige Text der EU-Konformittserklrung ist unter der folgenden Internetadresse verfgbar: https://europe.yamaha.com/en/support/compliance/doc.html

SV FRENKLAD EU-FRSKRAN OM VERENSSTMMELSE Hrmed frskrar Yamaha Music Europe GmbH att denna typ av radiout- rustning [DTX-PROX] verensstmmer med direktiv 2014/53/EU. Den full- stndiga texten till EU-frskran om verensstmmelse finns p fljande webbadress: https://europe.yamaha.com/en/support/compliance/doc.html

IT DICHIARAZIONE DI CONFORMIT UE SEMPLIFICATA Il fabbricante, Yamaha Music Europe GmbH, dichiara che il tipo di appare- cchiatura radio [DTX-PROX] conforme alla direttiva 2014/53/UE. Il testo completo della dichiarazione di conformit UE disponibile al seguente indirizzo Internet: https://europe.yamaha.com/en/support/compliance/doc.html

ES DECLARACIN UE DE CONFORMIDAD SIMPLIFICADA Por la presente, Yamaha Music Europe GmbH declara que el tipo de equipo radioelctrico [DTX-PROX] es conforme con la Directiva 2014/53/ UE. El texto completo de la declaracin UE de conformidad est disponible en la direccin Internet siguiente: https://europe.yamaha.com/en/support/compliance/doc.html

PT DECLARAO UE DE CONFORMIDADE SIMPLIFICADA O(a) abaixo assinado(a) Yamaha Music Europe GmbH declara que o pre- sente tipo de equipamento de rdio [DTX-PROX] est em conformidade com a Diretiva 2014/53/UE. O texto integral da declarao de conformi- dade est disponvel no seguinte endereo de Internet: https://europe.yamaha.com/en/support/compliance/doc.html

NL VEREENVOUDIGDE EU-CONFORMITEITSVERKLARING Hierbij verklaar ik, Yamaha Music Europe GmbH, dat het type radioappa- ratuur [DTX-PROX] conform is met Richtlijn 2014/53/EU. De volledige tekst van de EU-conformiteitsverklaring kan worden geraadpleegd op het vol- gende internetadres: https://europe.yamaha.com/en/support/compliance/doc.html

BG Yamaha Music Europe GmbH , [DTX-PROX] 2014/53/ . : https://europe.yamaha.com/en/support/compliance/doc.html

CS ZJEDNODUEN EU PROHLEN O SHOD Tmto Yamaha Music Europe GmbH prohlauje, e typ rdiovho zazen [DTX-PROX] je v souladu se smrnic 2014/53/EU. pln znn EU prohlen o shod je k dispozici na tto internetov adrese: https://europe.yamaha.com/en/support/compliance/doc.html

DA FORENKLET EU-OVERENSSTEMMELSESERKLRING Hermed erklrer Yamaha Music Europe GmbH, at radioudstyrstypen [DTX- PROX] er i overensstemmelse med direktiv 2014/53/EU. EU-overensstem- melseserklringens fulde tekst kan findes p flgende internetadresse: https://europe.yamaha.com/en/support/compliance/doc.html

ET LIHTSUSTATUD ELI VASTAVUSDEKLARATSIOON Kesolevaga deklareerib Yamaha Music Europe GmbH, et kesolev raadio- seadme tp [DTX-PROX] vastab direktiivi 2014/53/EL nuetele. ELi vas- tavusdeklaratsiooni tielik tekst on kttesaadav jrgmisel internetiaadressil: https://europe.yamaha.com/en/support/compliance/doc.html

EL / Yamaha Music Europe GmbH, [DTX-PROX] 2014/53/. : https://europe.yamaha.com/en/support/compliance/doc.html

HR POJEDNOSTAVLJENA EU IZJAVA O SUKLADNOSTI Yamaha Music Europe GmbH ovime izjavljuje da je radijska oprema tipa [DTX-PROX] u skladu s Direktivom 2014/53/EU. Cjeloviti tekst EU izjave o sukladnosti dostupan je na sljedeoj internetskoj adresi: https://europe.yamaha.com/en/support/compliance/doc.html

LV VIENKROTA ES ATBILSTBAS DEKLARCIJA Ar o Yamaha Music Europe GmbH deklar, ka radioiekrta [DTX-PROX] atbilst Direktvai 2014/53/ES. Pilns ES atbilstbas deklarcijas teksts ir pieejams d interneta vietn: https://europe.yamaha.com/en/support/compliance/doc.html

LT SUPAPRASTINTA ES ATITIKTIES DEKLARACIJA A, Yamaha Music Europe GmbH, patvirtinu, kad radijo rengini tipas [DTX-PROX] atitinka Direktyv 2014/53/ES. Visas ES atitikties deklaracijos tekstas prieinamas iuo interneto adresu: https://europe.yamaha.com/en/support/compliance/doc.html

HU EGYSZERSTETT EU-MEGFELELSGI NYILATKOZAT Yamaha Music Europe GmbH igazolja, hogy a [DTX-PROX] tpus rdi- berendezs megfelel a 2014/53/EU irnyelvnek. Az EU-megfelelsgi nyilatkozat teljes szvege elrhet a kvetkez internetes cmen: https://europe.yamaha.com/en/support/compliance/doc.html

PL UPROSZCZONA DEKLARACJA ZGODNOCI UE Yamaha Music Europe GmbH niniejszym owiadcza, e typ urzdzenia radiowego [DTX-PROX] jest zgodny z dyrektyw 2014/53/UE. Peny tekst deklaracji zgodnoci UE jest dostpny pod nastpujcym adresem interne- towym: https://europe.yamaha.com/en/support/compliance/doc.html

RO DECLARAIA UE DE CONFORMITATE SIMPLIFICAT Prin prezenta, Yamaha Music Europe GmbH declar c tipul de echipa- mente radio [DTX-PROX] este n conformitate cu Directiva 2014/53/UE. Textul integral al declaraiei UE de conformitate este disponibil la urmtoarea adres internet: https://europe.yamaha.com/en/support/compliance/doc.html

SK ZJEDNODUEN E VYHLSENIE O ZHODE Yamaha Music Europe GmbH tmto vyhlasuje, e rdiov zariadenie typu [DTX-PROX] je v slade so smernicou 2014/53/E. pln E vyhlsenie o zhode je k dispozcii na tejto internetovej adrese: https://europe.yamaha.com/en/support/compliance/doc.html

SL POENOSTAVLJENA IZJAVA EU O SKLADNOSTI Yamaha Music Europe GmbH potrjuje, da je tip radijske opreme [DTX- PROX] skladen z Direktivo 2014/53/EU. Celotno besedilo izjave EU o skladnosti je na voljo na naslednjem spletnem naslovu: https://europe.yamaha.com/en/support/compliance/doc.html

FI YKSINKERTAISTETTU EU-VAATIMUSTENMUKAISUUSVAKUUTUS Yamaha Music Europe GmbH vakuuttaa, ett radiolaitetyyppi [DTX-PROX] on direktiivin 2014/53/EU mukainen. EU-vaatimustenmukaisuusvakuutuk- sen tysimittainen teksti on saatavilla seuraavassa internetosoitteessa: https://europe.yamaha.com/en/support/compliance/doc.html

TR BASTLETRLM AVRUPA BRL UYGUNLUK BLDRM bu belge ile, Yamaha Music Europe GmbH, radyo cihaz tipinin [DTX- PROX], Direktif 2014/53/ AB'ye uygunluunu beyan eder. AB uyumu bey- annn tam metni aadaki internet adresinden edinilebilir: https://europe.yamaha.com/en/support/compliance/doc.html

6

DTX-PROX Owners Manual

Welcome

Thank you for purchasing this Yamaha DTX-PROX.

The DTX-PROX is a drum trigger module that you can use for playing electronic drum

kits and drum pads at homes, studios or live venues.

To get the most out of your DTX-PROX, be sure to read this Owners Manual carefully.

And after reading through this manual, be sure to store it in a safe place so that you can

refer back to it again as needed.

Included Accessories

Owners Manual (this book)

AC adaptor

Module holder

Module holder wing bolts ( 4)

Cubase AI Download Information

How to Attach the Module Holder

Exploded view DTX-PROX

Module holder wing bolts

Holder clamp

Module Holder

NOTE The module holder is compatible with standard drum hardware (22.2-mm or 7/8-inch diameter).

7

DTX-PROX Owners Manual

About the Manuals The following manuals are provided for using the DTX-PROX. These manuals are intended for users of the DTX-PROX.

Owners Manual (this book)

Setup Guide Explains how to attach and setup the DTX-PROX for producing sound.

Basic Guide Describes the fundamentals needed to operate the DTX-PROX.

Application Guide Describes parameter settings and other more advanced uses.

Reference Describes troubleshooting techniques and contains other reference materials.

Reference Manual

The Reference Manual provides a description of all the functions that can be accessed by pressing the [MENU] button as well as other advanced settings that can be used with the DTX-PROX.

Data List

This provides lists of Kit and Effect names in the DTX-PROX, and MIDI related information.

iPhone/iPad Connection Manual Smart Device Connection Manual for Android

Describes how to connect smartphones and tablets.

Printed Manual

Digital Manual (PDF)

The digital format manuals listed above can be obtained from the Yamaha Downloads web page. To do so, go to the web page using the following URL, enter DTX-PROX in the Model Name field, and then click Search.

Yamaha Downloads: https://download.yamaha.com/

8 DTX

Features of the DTX-PROX Intuitive operation for playing your ideal drum sounds Includes natural drum sounds with real ambience, played by top studio drummers

and recorded in renowned studios, including Real World Studios.

Includes unique KIT MODIFIERS giving you intuitive control of Ambience, Comp, and Effectsthe core elements of the drum sound creation (page 33).

Equipped with a high-quality headphone amplifier that delivers high fidelity reproduction of all drum sounds.

High-quality tone generator that enables natural expressive control like that of acoustic drumswith high-definition dynamics, high-performance effects pro- cessing, position sensing (*1) on snare and ride cymbal pads, low latency and 256 polyphony.

The instrument features LED rotary faders that allow easy access to parameters for drum sound creation and intuitive control of external devices during live perfor- mances

Useful for live performance The Live Set feature lets you prepare a custom sequence of kit, tempo, audio file,

and other parameters in, for example, the order of a performance set list and switch among settings with a single step operation as you play live.

Routing flexibility enables each of the instrument sounds, such as snare and kick, to be sent separately to the mixer using 8 lines from the INDIVIDUAL OUTPUT jacks.

Both stereo phone and stereo mini jacks are available for PHONES and AUX IN. No adaptor or mixer is needed when connecting external devices.

Boost your drumming skills through effective practice A sophisticated programmable metronome allows you to adjust the volume of

each click beat, change the tone of the click sound, and much more (page 42).

You can record or playback your songs using the build-in recorder or a USB flash drive (page 46).

Enables you to create music, make a video of your performance, and share your video over the Internet. The instrument is compatible with iOS or Android apps such as RecnShare. By dig-

itally connecting to smart devices via a USB cable, you can record and playback high quality sound. You can also play the drums along with your favorite music or make a video of your performance for uploading to social networking sites (*2) (page 23).

Audio playback available via Bluetooth Audio connection (*3)

Includes Steinberg Cubase AI for comprehensive music production tools (page 54).

*1 For more information on the list of compatible drum pads, refer to the Pad Module Compatibility Table.

*2 The DTX-PROX is a class compliant USB device. A separate cable is required for connecting to a com- puter or to a smartphone.

*3 For details, see Panel Controls and Functions on page 10.

-PROX Owners Manual

9DTX-PROX Owners Manual

PRECAUTIONS 2

Welcome 6

Included Accessories 6

About the Manuals 7 Printed Manual.............................................................................. 7 Digital Manual (PDF) .................................................................... 7

Features of the DTX-PROX 8

Panel Controls and Functions 10 Top Panel ................................................................................... 10 Front Panel ................................................................................. 12 Rear Panel.................................................................................. 13

Setup Guide 14 Preparations ............................................................................... 14 Installing the DTX-PROX ............................................................ 14 Turning On or Off........................................................................ 17 Changing the Overall Settings .................................................... 19 Using a USB Flash Drive ............................................................ 21 Using Smart Devices .................................................................. 23 Listening to Audio Data from a Smart Device through the DTX-PROX (Bluetooth Audio Function) ............................... 24

Basic Guide 26 Structure of the Kit ...................................................................... 26 Playing the Pads......................................................................... 27 Basic Operation of the DTX-PROX............................................. 32 Changing the Drum Set Sound (Building Your Own Drum Set) . 34 Using the Click (Metronome) ...................................................... 42 Creating Your Own Click (Metronome) Settings......................... 43 Changing the Trigger Settings .................................................... 45 Recording Your Performance ..................................................... 46 Connecting a PA System............................................................ 49 Using Live Sets........................................................................... 50

Application Guide 51 Connecting Separately Sold Add-ons and External Devices...... 51

Reference 55 Message List............................................................................... 55 Troubleshooting .......................................................................... 57 Specifications.............................................................................. 60 Index ........................................................................................... 61

Contents

10 DT

M C f

K A ( K

F S

D F S e

N A T s b t ( s C w

Panel Controls and Functions

Top Panel

X-PROX Owners Manual

ode Select knob hanges the mode (Kit, Click, Trigger, Recorder and Live set). Shows the screen

or each mode.

IT MODIFIER knobs djust the amount of Ambience (the background sounds of the location), Comp

the punchiness or loudness of the sound), Effect (other effects assigned to the it)

Structure of the Kit (page 26) Adjusting (Modifying) the Sound Effects (page 33)

ader Select knob elects the function for assigning to the LED Rotary Faders. (page 34)

KIT

CLICK

TRIGGER

RECORDER

LIVE SET

[AMBIENCE] knob [COMP] knob [EFFECT] knob

MIXER

INST

TUNING

MUFFL (Muffling)

FX (Effects)

CUSTM (Custom)

isplay unction Buttons 13 ([F1], [F2], [F3]) elects the functions that appear at the bottom of ach screen.

OTICE bout the mark: he mark appears in the upper right of the creen when the Kit, Click, and other settings have een changed. This is to remind you that the set-

ings have changed but have not yet been saved Store). The mark disappears when you store the ettings (page 40). When you change the Kit or lick without first storing the settings, the changes ill be lost.

F1 F2 F3

Cross stick setting (page 28) May not be shown depending on the pad

EFFECT screen (page 33)

How to read the KIT screen

LED Rotary Faders Changes the settings of the function selected with the Fader Select knob. Changes in val- ues are shown in the indicators.

120

11DTX-PROX Owners Manual

Panel Controls and Functions

Increases or decrease the value(s). The knob is useful for changing multiple values, while the buttons are useful for changing the value in steps. In this manual, the [][+] knob, the [] button and the [+] button are collectively called the [][+] controllers for situations where you can use either the knob or the buttons.

[PAD SELECT] button Shows the Trigger Input screens or the Trigger Input Source screen. For more information, refer to the Reference Manual (PDF).

NOTE Press this button to select a pad while changing settings with the LED rotary faders.

[][+] knob [] button [+] button

[ ] (Standby/On) switch (page 17) Switches the power between standby (off) and on.

Click Tempo Display

[TEMPO] knob (page 42) Adjusts the tempo.

[CLICK] button (page 42) Starts or stops the click (metronome). The indicator flashes in sync with the click tempo.

[AUDITION] button Use this button to check the sound of the cur- rently selected trigger input source (Reference Manual (PDF)). As a default setting, the voice assigned to the head of the snare pad connected to the [qSNARE] jack is played.

Buttons for showing screens

[MENU] button Accesses the advanced settings screen. For more detailed information, refer to the Reference Manual (PDF).

[STORE] button STORE screen (page 40)

Stores Kit, Click, Trigger, or, Live set settings that you have created.

[EXIT] button Cancels the action or returns to the screen one level higher.

NOTE This button can also be used as a Panic Button to stop the KIT sounds (on top screen for each mode).

Bluetooth figure mark (page 24)

Bluetooth capability Depending on the country in which you pur- chased the product, the instrument may not have Bluetooth capability. If the Bluetooth logo is shown or printed on the control panel, this means that the product is equipped with Blue- tooth functionality.

Sliders These change the corresponding volume levels.

[AUX IN] (auxiliary inputs from the [AUX IN] jacks on front and rear panels)

[AUDIO] (audio including USB audio, Bluetooth audio, Song, and recorder playback)

[CLICK] (click)

[OUTPUT] (outputs from the OUTPUT [R]/[L/MONO] jacks)

[PHONES] (headphones)

12

Panel Controls and Functions

Front Panel

Stereo mini phone plug (3.5 mm)

Stereo mini plug (3.5 mm)

[PHONES] (Headphone) jack (page 16) For connecting headphones. The one on the left is a standard ste- reo phone type (6.3 mm) output jack, and the one on the right is a stereo mini phone type (3.5 mm) output jack.

CAUTION Do not use headphones for a long period of time at high vol- ume. Doing so can cause loss of hearing.

[AUX IN] (auxiliary input) jack Connect to the headphone jack on a smart phone or portable music player.

Standard stereo phone plug (6.3 mm)

DTX-PROX Owners Manual

13

Panel Controls and Functions

DTX-PROX Owners Manual

Rear Panel

Trigger Input jacks [!4] jack to [qSNARE] jack Connects the DTX series pads. To connect the pads included in your Drum Kit, refer to the Assem- bly Manual. These trigger input jacks also accept separately sold add-ons. For more information, see About the Trigger Input Jacks (page 51).

XP125SD-X

PCY175

[MIDI OUT] connector [MIDI IN] connector Connects MIDI devices for sending and receiving MIDI messages with the DTX-PROX.

Standard stereo phone plug (6.3 mm)

Standard phone plug (6.3mm)

MIDI cable

[USB TO DEVICE] terminal (page 21) Connects a USB flash drive. Cannot be used with other USB devices.

Using a USB Flash Drive (page 21)

DC IN jack (page 14) Use the AC adap- tor that came with the DTX-PROX.

[USB TO HOST] terminal (page 54) Connect a computer or smart device such as a smart phone or a tablet to send and receive digital signals (audio and MIDI).

Computers Connecting a Computer (page 54) Reference Manual (PDF)

Smart devices Using Smart Devices (page 23)

Cord hook Wrap the AC adaptor cord around this hook to prevent accidental unplug- ging during use.

CAUTION Excessive bending can damage the AC adaptor cord and create a fire hazard. For this reason, make sure that the power cord is not bent at an extreme angle when wrapped around the hook.

AC adaptor cord Cord hook

OUTPUT [R]/[L/MONO] jacks (UNBALANCED) (page 14) Connect to powered speakers or other such PA system. These jacks are standard phone type output jacks. If mono output is required, use only the [L/MONO] jack. USB cable

[AUX IN] (auxiliary input) jack Stereo standard phone jack for con- necting an electronic instrument or for inputting audio from a PA sys- tem. The audio signals from the [AUX IN] jack on the front panel and the [AUX IN] on the rear panel are mixed. For more information, refer to the Reference Manual (PDF).

Standard stereo phone plug (6.3 mm)

[INDIVIDUAL OUTPUT] jacks (UNBALANCED) (page 49) Output the sound of each instrument, such as snare and kick.

Standard stereo phone plug (6.3 mm)

14 DT

Setup Guide

This provides information on setup and initial settings in preparation for playing.

This completes set up.

First, install the DTX-PROX. There are three different ways of installation as shown below.

Attach the DTX-PROX onto the rack of your drum kit. (For more information, refer to the Assembly Manual.)

Use the included module holder (page 6) to attach the standard drum hardware. (See Integrating Electronic & Acoustic Drums on page 53.)

Place on a flat surface

After installing the DTX-PROX, connect cables to the Pads. For more information on the connections, refer to the specific Assembly Manual of your drum kit.

Preparations

Workflow

Installing the DTX-PROX

Connecting the AC adaptor

Connecting Headphones

Turning On

Initial Setup (Trigger Setup Wizard)

Installing the DTX-PROX

X-PROX Owners Manual

Installing the DTX-PROX

Setup Guide

Connecting the AC adaptor

1. Make sure that the power is turned off (all panel lights and the screen backlight are off).

2. For removable plug type AC adaptors only: Make sure that the plug is not disconnected.

3. Connect the AC adaptor.

WARNING Only use the specified AC adaptor (page 60). Using a different AC adaptor can cause malfunction, overheating, fire, and other problems. This may void the warranty so please take careful note.

CAUTION Locate the DTX-PROX close to an AC outlet. If you notice any abnormalities during operation, turn the power off immedi- ately and unplug the AC adaptor.

WARNING For AC adaptors with a removable plug, only use the

AC adaptor with the plug attached, and keep the plug. Plugging only the plug into the power outlet can cause electric shock or fire.

If the removable plug comes off from the AC adaptor, avoid touching the metal parts on the plug and slide the AC adaptor onto the plug until you hear it lock on to the adaptor with a click. Also, make sure you keep any foreign objects out of the plug. This can cause electrical shock, short circuit, or failure.

WARNING Make sure to use the specified AC adaptor.

No screen backlight

Slide in the direction indicated with the arrow.

Plug

DC IN jack (page 60)

15DTX-PROX Owners Manual

16

Installing the DTX-PROX

Setup Guide

4. Hook the AC adaptors cord around the cord hook to secure it in place.

5. Plug the AC adaptors AC plug into a domes- tic power outlet.

Connecting Headphones Connect the headphones to the [PHONES] (headphone) jack.

To adjust the headphone volume, use the [PHONES] slider. To adjust the headphone EQ, set the Fader Select knob to CUSTM, and use the LED rotary faders.

One standard stereo phone jack and one stereo mini phone jack are available. Select the proper jack that matches the con- nector size of the cable. The output volume may be lower than expected if both phone jacks are used at the same time.

CAUTION Excessive bending can damage the AC adaptor cord and create a fire hazard. Ensure, therefore, that the power cord is not bent at an extreme angle when wrapped around the hook.

CAUTION Even when the [ ] (Standby/On) switch is in standby status (display is off), electricity is still flowing to the instrument at the minimum level. When you are not using the DTX-PROX for a long period of time, make sure that you unplug the AC adaptor from the wall AC outlet.

NOTE When disconnecting the AC adaptor, turn the instrument and then carry out this procedure in reverse order.

CAUTION Do not use headphones at high volume for an extended period of time. Doing so can cause loss of hearing.

Cord hookAC adaptor cord

Power outlet

AC adaptor

Front panel side

DTX-PROX Owners Manual

Turning On or Off

Setup Guide

Turning On

1. Lower the [OUTPUT] and [PHONES] sliders to set the volume levels to their minimum.

2. Press the [ ] (Standby/On) switch.

If the initial setup is already complete, the KIT screen appears directly after the startup screen, without showing the Trigger Setup Wizard.

3. If you are connected to a PA system: Turn the external speakers on.

Turning On or Off

Initial Setup (Trigger Setup Wizard) When you turn on your DTX-PROX for the first time, the Initial Setup page will be displayed. On this page, you will be required to specify the following. When you specify the model number, the DTX-PROX will automati- cally optimize the trigger output levels for all of your pads.

1. Identify your drum kit using the [][+] controllers and press the button below OK ([F3]). Your drum kits model number is indicated on the Assembly Manual for your drum kit. Make sure to select the proper pad type (DTX**K-X or DTX**K-M) for your particular drum kit.

2. When the confirmation screen appears, press the button below YES ([F1]). When the initial setting is complete, the KIT screen appears.

IMPORTANT

NOTE You can change the specified drum kit at any time after completing Initial Setup. (Changing the Trigger Settings (page 45))

* XSTICK: May not be shown depending on the pad

Power on

17DTX-PROX Owners Manual

18

Turning On or Off

Setup Guide

Turning Off

1. If you are connected to a PA system: Turn the external speakers off.

2. Lower the [OUTPUT] and [PHONES] sliders to set the volume levels to their minimum.

3. Hold down the [ ] (Standby/On) switch. The DTX-PROX is in Standby and the display and lights are off.

NOTICE The DTX-PROX automatically stores settings when the power is turned off, so do not unplug the AC adaptor until the

LCD screen is turned off completely.

Any unsaved Kit, Click, Trigger settings, and Live Set data will be lost, so always save (Store) data before turning the power off.

Power off

Hold down

All off

DTX-PROX Owners Manual

Changing the Overall Settings

Setup Guide

Auto Power-Off The Auto Power-Off function automatically turns off the DTX-PROX after a certain period of inactivity. The factory default is set at 30 minutes.

Auto Power-Off Quick Cancel

First, make sure that the DTX-PROX is turned off. Then, while holding down the [MENU] button, press the [ )] (Standby/ On) button to cancel the Auto Power-Off function. The func- tion will remain off until you set a new Auto Power-Off time.

Changing the Overall Settings

NOTICE Unsaved data is lost when the DTX-PROX is turned off with the Auto Power-Off function. Always store data before turn-

ing the power off.

In certain modes of operation, the Auto Power-Off function will not turn off the DTX-PROX when the set time has elapsed. So we recommend that you always turn off the DTX-PROX manually when you are finished using it.

If you expect the DTX-PROX to be inactive for a certain length of time while connected to external audio equipment or a PA, we recommend fully lowering the volume on the external equipment. Alternatively, you can disable the Auto Power- Off function to ensure that the DTX-PROX stays on.

NOTE To set the Auto Power-Off to a time other than 30 minutes, access the setting from the [MENU] button. (MENU/Utility/General)

19DTX-PROX Owners Manual

20

Changing the Overall Settings

Setup Guide

Restoring DTX-PROX Settings to the Factory Defaults (Factory Reset)

Use the Factory Reset function to restore the DTX-PROXs settings to their factory defaults, even if you have accidentally overwritten them.

Performing a Factory Reset

First, make sure that the DTX-PROX is turned off. Then, while holding down the [] and [+] buttons, press the [ ] (Standby/ On) button to perform the Factory Reset function.

NOTICE A factory reset overwrites any settings you have made with the corresponding factory defaults. Save any important user- defined data to a USB flash drive before carrying out a factory reset. For more information, refer to the Reference Manual (PDF). (MENU/File)

NOTE You can also access the factory reset with the [MENU] button. (MENU/Factory Reset)

DTX-PROX Owners Manual

Using a USB Flash Drive

Setup Guide

Connect a USB flash drive to the [USB TO DEVICE] terminal on the rear panel of the DTX-PROX and record your perfor- mance directly to the USB flash drive. Also, you can save DTX-PROX settings to and load settings from a USB flash drive.

Connecting a USB Flash Drive to the DTX-PROX

Precautions When Using the [USB TO DEVICE] Terminal When connecting a USB flash drive to the [USB TO DEVICE] terminal, be sure to follow the important precautions below.

Compatible USB Devices

USB flash drives only Please check the URL shown below for a list of compatible USB flash drives.

https://download.yamaha.com/

Connecting a USB Flash Drive

When connecting a USB device to the [USB TO DEVICE] terminal, make sure that the connector on the DTX-PROX is appropriate and that it is connected in the proper direction. Although USB devices 2.0 to 3.0 can be used on the DTX-PROX, the amount of time for saving to or loading from the USB device may differ depending on the type of data or the status of the instrument.

Using a USB Flash Drive

NOTE For more information about the handling of USB flash drives, refer to the owners manual of your USB flash drive.

NOTE Other USB devices such as USB hub, mouse, computer keyboard, cannot be used.

A USB cable cannot be used to connect a USB device to the [USB TO DEVICE] terminal.

NOTICE The rating of the [USB TO DEVICE] terminal is a maximum of 5 V / 500 mA. Do not connect USB devices having a rating above this, since this can cause damage to the instrument itself.

NOTICE Avoid connecting or disconnecting the USB device during playback/recording and file management operations (such as

Save, Copy, Delete, and Format), or when accessing the USB device. Failure to observe this may result in freezing of the operation of the instrument or corruption of the USB device and the data.

When connecting then disconnecting the USB device (and vice versa), make sure to wait a few seconds between the two operations.

21DTX-PROX Owners Manual

22

Using a USB Flash Drive

Setup Guide

Formatting the USB Flash Drive

Some USB flash drives should be formatted with this instrument before they can be used. For information on how to format the USB flash drive, refer to the Reference Manual (PDF). (MENU/File/Format)

To Protect Your Data (Write Protection)

To prevent important data from being inadvertently erased, write-protect the USB flash drive. When you are saving data to the USB flash drive, make sure you disable the write-protect first.

NOTICE The format operation erases any previously existing data. Make sure that the USB flash drive you are formatting does not contain any important data.

DTX-PROX Owners Manual

Using Smart Devices

Setup Guide

Connecting a smart device to the [USB TO HOST] jack establishes a digital connection and allows you to:

Record and play back high-quality audio using apps Practice, record (both audio and video), and share your recordings on social networks using RecnShare

Additional parts are required for connecting a smart device. For more information on the connection, refer to the iPhone/iPad Connection Manual or Smart Device Connection Man- ual for Android.

For details on compatible smart devices and smart device applications such as RecnShare, refer to the web page below.

https://download.yamaha.com/

Using Smart Devices

NOTICE Before connecting devices, make sure the volume levels on all external devices are set at their minimum.

Be sure to place your smart device on a stable surface to prevent it from falling over and being damaged.

NOTE To eliminate the risk of interference due to noise by your smart device when used in combination with the DTX-PROX, turn on the Airplane Mode and then turn on Wi-Fi.

23DTX-PROX Owners Manual

24

Listening to Audio Data from a Smart Device through the DTX-PROX (Bluetooth Audio Function)

Setup Guide

Bluetooth capability Depending on the country in which you purchased the product, the DTX-PROX may not have Bluetooth capability. If the Bluetooth logo is shown or printed on the top panel, this means that the product is equipped with Bluetooth functionality.

You can input the sound of the audio data saved in a Bluetooth-equipped device, such as a smart phone or digital audio player, to the DTX-PROX and listen to it through the headphones or speakers connected to the DTX-PROX. The input audio data can be recorded. (page 46)

* Bluetooth-equipped device In this manual, Bluetooth-equipped device refers to a device that can transmit audio data on it to the DTX-PROX using the Bluetooth function, via wireless communication. (i.e., smart phones and portable audio players.)

Pairing with the Bluetooth-equipped device To connect the Bluetooth-equipped device for the first time, the Bluetooth-equipped device and the DTX-PROX must be paired. Once the device and the DTX-PROX are paired, it is not necessary to pair the two again (unless youve disabled pairing).

Paring

Pairing means to register Bluetooth-equipped smart devices on the DTX-PROX and establish the mutual recognition for wireless communication between the two.

1. Hold down the [MENU] button. The screen appears while the device is being paired. To cancel pairing, use the button below CANCEL ([F3]).

2. Turn the Bluetooth setting ON on the Blue- tooth-equipped device and select DTX- PROX AUDIO from the list. Make sure to complete the settings on the smart device

within 5 minutes. After that, the pairing mode ends auto- matically.

If you are required to enter a passkey, enter the numerals 0000.

Listening to Audio Data from a Smart Device through the DTX-PROX (Bluetooth Audio Function)

Before using the Bluetooth function, be sure to read About Bluetooth on page 4.

NOTE Bluetooth headphones or speakers cannot be connected.

Hold down

DTX-PROX Owners Manual

Listening to Audio Data from a Smart Device through the DTX-PROX (Bluetooth Audio Function)

Setup Guide

When the pairing completed, the (Bluetooth) mark appears on top screen for each mode.

3. Play back audio data on the smart device to confirm that the headphones or speakers connected to the DTX-PROX can output the audio sound. You can adjust the volume of the sound input via Blue- tooth by the [AUDIO] slider.

When you turn on the DTX-PROX the next time, the last- connected smart device will be connected to the DTX- PROX automatically, if the Bluetooth function of the smart device and the DTX-PROX is set to on. If it is not connected automatically, select the model name of the instrument from the connection list on the smart device.

To switch the Bluetooth function on the DTX-PROX, press the [MENU] button to open the screen. For more information, refer to the Reference Manual (PDF). (MENU/Bluetooth)

25DTX-PROX Owners Manual

26 DT

Basic Guide

A Kit is a combination of drum set sounds and the sound modifier settings that enhance the sounds, such as Ambience, Comp (Compressor) and Effects. This drum trigger module contains numerous sets of preset kits, and you can change the drum set sounds by selecting another kit or by changing the sound modifier settings.

Each drum or percussion instrument in the drum set is called an instrument or Inst, and you can play the Inst sounds by striking drum pads.

Structure of the Kit

Compressor

EFFECT

Kit

Drum set Ambience Comp Effects

Other settings for the Kit

Snare drum Kick CowbellCymbal Tambourine Other

instruments

Example of the Instruments (Inst):

X-PROX Owners Manual

Playing the Pads

Basic Guide

To play the Inst sounds, strike the pads connected to the DTX-PROX. You can play different sounds by striking different sections (or Zones) of the pad, depending on the number of zones available on the pad. When position sensing is available, you can express a subtle nuance by striking different locations within a Zone.

Playing the Pads

Pad Type Multi Piezo Single Piezo

Number of Zones

2 1 2 3

Produces two differ- ent sounds (one for each zone)

Produces the same sound regardless of where the pad is struck.

Also called the monaural pads or 1-zone pads.

Produces two differ- ent sounds (one for each zone)

Produces three different sounds (one for each zone).

Also referred to as 3-zone pads.

Zone

Example XP125SD-X TP70 RHH135 PCY135 XP80

NOTE For the information on the type of the drum sticks or beaters, refer to the Owners Manual for the pad.

Rim

Head Pad

Bow

Edge

Bow Cup

Edge

Pad Rim B

Rim A

27DTX-PROX Owners Manual

28

Playing the Pads

Basic Guide

Snare and Tom Strike different sections of the pad in the same way you would play an acoustic snare drum or tom. With the snare pad (the pad with position sensor connected to the [qSNARE] jack), you can create natural tonal changes according to the location within the Zone.

Head shots

Strike the main surface of the pad to produce a conventional head hit sound.

Multi Piezo pad with position sensing:

With certain snare sounds, the sound changes depending on how far from the rim you strike.

Open rim shots

Strike the head and the rim at once to produces a rim shot sound.

Multi piezo pads with position sensing:

You can use normal rim shots or shallow rim shots. Depending on the distance from the rim, the rim shot sound changes slightly.

Single piezo 3-zone pads:

Strike the open rim.

Closed rim shots, (cross sticking)

Strike only the rim. Do not touch the head.

Multi piezo pads:

Press the button below XSTICK ([F2]) in the KIT screen to switch between on (for playing the cross-stick sound) or off (for playing the open rim shot sound).

Single piezo 3-zone pads:

Strike the closed rim.

Head Head

Rim

Head

Open rim

Rim Closed rim

DTX-PROX Owners Manual

Playing the Pads

Basic Guide

Hi-hats Strike different sections of the pad in the same way you would play an acoustic hi-hat cymbal.

*1 The front side of the pad is indicated by the Yamaha logo.

Bow shots

Striking the main surface of the hi-hat pad (i.e., the bow section located between the cup and edge) produces a bow shot sound.

Edge shots

Striking the front side on the outer edge of the hi-hat pad produces an edge shot sound.

*1

Make sure that the drumstick is parallel to the pad surface when striking the pad. The edge sensor switch on the cymbal pad may not react properly when the pad is struck completely from the side.

Open/Close

You can produce an open hi-hat sound by striking the hi-hat pad with the hi-hat pedal fully open.

You can produce a closed hi-hat sound by striking the hi-hat pad with the hi-hat pedal fully pressed.

Different hi-hat sound is produced depending on the how much the pedal is opened or pressed.

Foot-close sounds

You can press down the hi-hat pedal to create a foot-close sound without having to strike the hi-hat pad.

Hi-hat splash sounds

Pressing down the hi-hat pedal and then immediately releasing it produces a hi-hat splash sound.

29DTX-PROX Owners Manual

30

Playing the Pads

Basic Guide

Cymbals Strike different sections of the pad in the same way you would play an acoustic cymbal. With the ride cymbal (the pad with position sensor connected to the [iRIDE] jack), you can create natural tonal changes according to the location within the Zone.

Bow shots

Striking the main surface of the cymbal pad (i.e., the bow section located between the cup and edge) produces a bow shot sound.

With the ride cymbal, strike the front side of the bow section, you can create natural tonal changes according to the location within the Zone.

*1

Edge shots

Striking the front side on the outer edge of the cymbal pad produces an edge shot sound.

*1

Make sure that the drumstick is parallel to the pad surface when striking the pad. The edge sensor switch on the cymbal pad may not react properly when the pad is struck completely from the side.

Bell shots

Striking the bell (cup) produces a bell shot sound.

Choking

Grabbing the front side on the outer edge of a cymbal pad immediately after striking it will mute the sound being produced.

*1

Front side on the outer edge

Front side on the outer edge

DTX-PROX Owners Manual

Playing the Pads

Basic Guide

*1 The front side of the pad is indicated by the Yamaha logo.

Muting

Striking the pad while holding the front side of the outer edge will produce a muted sound.

*1

Front side on the outer edge

31DTX-PROX Owners Manual

32

Basic Operation of the DTX-PROX

Basic Guide

Selecting a Kit

1. Set the Mode Select knob to KIT. The KIT screen appears.

2. Use the [][+] controllers to select a kit.

Basic Operation of the DTX-PROX

NOTE If youve inadvertently selected another Kit before storing the Kit being edited, you can use the recall function to recall the edited contents. For more information, refer to the Reference Manual (PDF). (MENU/Job/Kit/Recall)

* This screen is shown when multi-piezo pads are connected.

Kit number

Kit name

P***: Preset Kits (Presets that are already stored in the DTX-PROX)

U***: User Kits (Kits you have created)

or

DTX-PROX Owners Manual

Basic Operation of the DTX-PROX

Basic Guide

Adjusting (Modifying) the Sound Effects

Changing the Effect Type to Apply

1. Press the button below EFFECT ([F3]).

2. Press the button below EFFECT M ([F3]) to select the effect you wish to set.

3. Use the [] [+] controllers to select the effect type.

[AMBIENCE] knob Adjusts the amount of ambience or the reflective sounds of the virtual room

[COMP] knob Adjusts the amount of compression or the amount of the punchiness or loudness of the sound

[EFFECT] knob Adjusts the amount of other effects assigned to the Kit

Maximum: All lit

Minimum: All off

Effect Selection

M: Master effect 1: Effect 1 2: Effect 2

or

33DTX-PROX Owners Manual

34

Changing the Drum Set Sound (Building Your Own Drum Set)

Basic Guide

With the DTX-PROX, you can build your own drum set by changing the drum set sound within the Kit. By changing the settings shown below, you can customize the drum set sound.

If you want to make more detailed changes to the settings, press the [MENU] button. For more information, refer to the Ref- erence Manual (PDF). (MENU/Kit Edit/Inst or MENU/Kit Edit/Voice)

Changing the Drum Set Sound (Building Your Own Drum Set)

Adjusting the Audio Balance

Replacing Instruments

Changing the Tunings Changing the Cymbal Size

Muffling (muting) the drum Sustain length of the cymbal

Hi-hat clutch positions, etc.

Changing the Amount of Effect to Apply

Creating Custom settings

Drum set

DISTORTION DELAY FLANGER PHASER

DTX-PROX Owners Manual

Changing the Drum Set Sound (Building Your Own Drum Set)

Basic Guide

Adjusting the Audio Balance Use the mixer to adjust the overall volume balance of the pads.

1. Set the fader select knob to MIXER. The MIXER screen appears.

2. Use the LED rotary faders to adjust the settings.

To adjust the volume of each pad, press the [MENU] button to change the Inst volume settings. To adjust the volume of each section of the pad (Zone), press the [MENU] button to change the Voice volume settings. For more information, refer to the Reference Manual (PDF).

3. Press the button below OK (F3).

NOTE The mixer setting is retained after switching to another Kit.

The mixer setting is not saved as a Kit setting.

Shown on the panel KICK SNARE TOM HI-HAT CRASH RIDE MISC

Pad Kick Snare Tom1 Tom2 Tom3

Hi-Hat Crash1 Crash2

Ride Others

Trigger input jack the pad is connected to

!2KICK qSNARE wTOM1 rTOM2 yTOM3

!1HI-HAT oCRASH1 !0CRASH2

iRIDE e, t, u, !3, !4

35DTX-PROX Owners Manual

36

Changing the Drum Set Sound (Building Your Own Drum Set)

Basic Guide

Replacing Instruments

1. Set the fader select knob to INST. The INST screen appears.

2. Strike the drum pad for which you wish to change the settings. The pad name appears on the upper right corner of the screen.

NOTE For the TOM, CRASH, and MISC pads, you can use the [PAD SELECT] button to change the pad selection. For more information, refer to the Reference Manual (PDF).

DTX-PROX Owners Manual

Changing the Drum Set Sound (Building Your Own Drum Set)

Basic Guide

3. Use the LED Rotary Faders to select an Instrument. The selected Instrument is shown on the screen.

4. Press the button below OK (F3).

Using Imported Sounds (.wav) You can import audio files (.wav) into the DTX-PROX to use as Inst sounds. For more information on importing audio files and settings, refer to the Reference Manual (PDF). For more information on using a USB flash drive, see Using a USB Flash Drive (page 21).

Inst name

Inst Category for the selected Instrument

Inst number

NOTE For the TOM, CRASH, and MISC pads, you can use the [PAD SELECT] button to change the pad selection. For more infor- mation, refer to the Ref- erence Manual (PDF).

37DTX-PROX Owners Manual

38

Changing the Drum Set Sound (Building Your Own Drum Set)

Basic Guide

Changing Settings such as Tuning and Muffling (muting) Inst settings such as tuning and muffling (muting) can be changed. Settings that can be changed with TUNING or MUFFL are different depending on the Inst Category.

1. Set the fader select knob to TUNING or MUFFL. The setting screen appears.

Inst Category for the selected instrument (INST)

Kick1 Kick2

Snare1 Snare2 Tom1 Tom2

Cymbal1 Cymbal2

HiHat1 HiHat2

Perc Effect User

TUNING Tuning

Determines the tuning (pitch).

Size

Simulates the effect of changing the cymbal size.

Size

Simulates the effect of changing the cymbal size.

Tuning

Determines the tuning (pitch).

MUFFL Muffling

Simulates the effect of changing the degree of muffling (or how much the drum head is muted)

Sustain

Determines the cymbals sustain time (i.e., how quickly the sound decays to silence).

Clutch

Simulates the effect of changing the hi-hats clutch position. The smaller the setting, the quicker an open hi-hat sound will decay to silence.

Decay

Determines how quickly the sound decays to silence.

NOTE Hi-Hat Clutch setting is applied to all Kits.

or

DTX-PROX Owners Manual

Changing the Drum Set Sound (Building Your Own Drum Set)

Basic Guide

2. Use the LED Rotary Faders to adjust settings.

3. Press the button below OK (F3).

Changing the Amount of Effect Applied to each Instrument The amount of effects (such as Effect1, Effect2, Transient) can be set independently for each Inst. For example, you can use these settings to apply deeper effects only to the snare. For more information, refer to the Reference Manual (PDF).

Creating Custom settings Other settings such as Master EQ, Phones EQ gain, volume of the individual click timing. and the send settings on MIDI control change can be customized. For more information, refer to the Reference Manual (PDF).

NOTE The CUSTM setting is retained after switching to another Kit.

The CUSTM setting is not saved as a Kit setting.

39DTX-PROX Owners Manual

40

Changing the Drum Set Sound (Building Your Own Drum Set)

Basic Guide

Saving a Customized Kit under a New Name

1. Press the [STORE] button. The KIT STORE screen appears.

2. Press the button below NAME ([F2)] to open the NAME screen.

3. Use the buttons below and ([F1] and [F3]) to select the character position, then use the [] [+] controllers to select a letter. A name of up to 12 characters can be set to the Kit.

Kit number and Kit name of the Kit you are editing.

User Kit number and User Kit name of the Store Destination.

or

Character position (cursor)

Character you want to

enter

DTX-PROX Owners Manual

Changing the Drum Set Sound (Building Your Own Drum Set)

Basic Guide

4. After entering all characters, press the button below OK ([F2]) and return to the STORE screen.

5. Use the [] [+] controllers to select a User Kit Number to store your Kit to.

6. After confirming the new Kit Number and Kit Name, press the button below STORE ([F3]).

When the Kit operation is complete, the display returns to the Kit screen.

NOTE You cannot save an edited Kit to a Preset Kit.

NOTICE When overwriting a Kit, the current Kit settings are replaced with the new settings. Before overwriting a Kit, ensure that the Kit contains no irreplaceable settings.

Overwrite? appears when the selected Kit Number already contains a Kit. If you want to overwrite to save the Kit, press the button below YES ([F1]). If you do not want to overwrite, press the button below NO ([F3]) and return to the previous screen where you can select another Kit number.

or

41DTX-PROX Owners Manual

42

Using the Click (Metronome)

Basic Guide

DTX-PROX Owners Manual

Practicing your drumming along with the click (metronome) sounds helps you perfect your rhythms.

Starting and Stopping the Click

1. Press the [CLICK] button to start the Click. Click sounds are played at the tempo shown in the Click Tempo display.

The lamp next to the [CLICK] button flashes in sync with the tempo while the Click sounds.

2. To stop the click, press the [CLICK] button again.

Changing the Tempo

1. Turn the [TEMPO] knob.

Setting the Click Beat Volume

1. Move the [CLICK] slider.

Using the Click (Metronome)

120

Creating Your Own Click (Metronome) Settings

Basic Guide

Set the Click (metronome) tempo, volume, etc.

1. Set the Mode Select knob to CLICK.

Creating Your Own Click (Metronome) Settings

Setting the Tempo by Tapping the Button

(Tap Tempo)

Tap the button at the desired tempo to set the tempo.

2. Press the button below TAP ([F1]).

The TAP screen appears.

3. Tap the button below TAP ([F3]) at least 3 times.

The tapped tempo is detected and appears on the Click tempo display.

NOTE You can also set the tempo by striking a pad connected to the Trigger Input jacks.

Changing the Volume of the Individual Click Timing

2. Press the button below VOLUME ([F2]).

3/8, 6/8, 9/8, 12/8, 15/8 beats only have settings for Acc, dot- ted quarter, eighth, and sixteenth notes. Press the button below ([F3]) to switch between Human voice1 and Human voice2 to change counts.

3. Use the buttons below and ([F1] and [F2]) to move the cursor and use [][+] to change the volume.

The VOLUME screen appears. Accents

Quarter notes

Eighth notes

Sixteenth notes

Eighth note triplets

Human voice

or

Changing Other Settings

Beat, Timer settings, click sound types, and other settings can be changed. Also, you can use your choice of a wav file as click sound. For more infor- mation, refer to the Reference Manual (PDF).

The CLICK screen appears.

Timer settings

Click number Click name

Volume settings for individual click timing

43DTX-PROX Owners Manual

44

Creating Your Own Click (Metronome) Settings

Basic Guide

Saving the Customized Click Setting under a New Name The Click settings you have customized can be saved in the same way as saving a kit. See Saving a Customized Kit under a New Name (page 40).

Using Saved Click Settings While the CLICK screen is shown on the display, use the [][+] controllers to select a user click.

or

DTX-PROX Owners Manual

Changing the Trigger Settings

Basic Guide

With the Initial setup (Trigger Setup Wizard), the DTX-PROX will automatically optimize the trigger output levels for all pads. You can adjust each of settings later or create a new Trigger setup. Several sets of customized trigger setups can be saved on the DTX-PROX.

Creating a customized trigger setup Trigger setups can be changed from the button below SET- TING ([F3]). For more information, refer to the Reference Manual (PDF).

Saving the customized trigger setup The Trigger setups you have customized can be saved in the same way as saving a kit. See Saving a Customized Kit under a New Name (page 40).

Selecting a Trigger setup

1. Set the Mode Select knob to TRIGGER. The TRIGGER screen appears.

2. Select the desired Trigger setup with the [][+] controllers.

Changing the Trigger Settings

NOTE The setting selected with the Trigger Setup Wizard appears as the first setting shown on the screen.

or

45DTX-PROX Owners Manual

46

Recording Your Performance

Basic Guide

Use the DTX-PROX to record your performance. When a USB flash drive is connected to the DTX-PROX, audio is recorded to the USB flash drive. You can overdub your performance onto an accompaniment song (input via the [AUX IN] jack or Bluetooth) and save your performance combined with the accompaniment song as a single audio file.

Recording to the DTX-PROX (when no USB flash drive is connected to the terminal)

1. Set the Mode Select knob to RECORDER.

Recording Your Performance

Recording

Recording time to the DTX-PROX is about 1 minute 30 seconds.

2. Press the button below ([F1]) to start recording.

While recording, the elapsed recording time (min: sec) appears.

3. Play the drums.

4. After you finish playing, press the button below ([F1]) to stop recording.

Playing Back

NOTE This is not displayed when there is no recorded song.

2. Press the > button ([F2]) to start playback.

While playing back, the elapsed play- back time (min: sec) appears.

3. To stop playback, press the button ([F2]).

Changing other settings

Other settings such as the play- back speed or the recording source can be changed. For more information, refer to the Refer- ence Manual (PDF).

NOTICE When your performance is

already recorded on the DTX-PROX, recording again on the DTX-PROX erases the previous recording.

Any performance recorded to the DTX-PROX will be lost when the power is turned off. If you wish to save your recordings, export the recorded data as audio files. For more information, refer to the Reference Manual (PDF). (MENU/Job/Recorder/ Export Audio)

Destination Playback speed

The RECORDER screen opens.

DTX-PROX Owners Manual

Recording Your Performance

Basic Guide

Recording to a USB Flash Drive

1. Connect a USB flash drive to the [USB TO DEVICE] terminal on the rear panel.

2. Set the Mode Select knob to RECORDER.

When a USB flash drive is connected You can record up to 90 minutes at a time. A new file is created every time you record. Simultaneous playback and recording to overdub your performance onto the currently playing

song.

Recording

3. Press the button below ([F1]) to start recording.

While recording, the elapsed recording time (min: sec) appears.

4. Play the drums.

5. After you finish playing, press the but- ton below ([F1]) to stop recording.

The RECORDER SAVE screen appears.

6. Press the button below SAVE ([F3]) and save the file.

Press the button below CANCEL ([F2]) if you do not want to save the file.

NOTE If you want to change the file name, press the button below NAME ([F1]) and enter a new name. (page 40)

Playing Back

NOTE This is not displayed when there is no recorded song.

3. Use the [][+] con- trollers to select a song for playback.

NOTE Up to 1,000 songs are recog- nized.

4. Press the button below > ([F2]) to start playback.

5. Press the button below ([F2]) to stop playback.

or

Changing Other Settings

Other settings such as the playback speed or the recording source can be changed. For more information, refer to the Reference Manual (PDF).

Destination

File name

Playback speed

The RECORDER (USB) screen appears.

47DTX-PROX Owners Manual

48

Recording Your Performance

Basic Guide

Overdub Recording Your Performance onto an Accompaniment Song

You can also overdub your performance onto an accompaniment song that youve imported onto a USB flash drive and save your performance combined with the accompaniment song as a single audio file.

Preparing an Accompaniment Song (Audio File)

Importing from a Computer Save the audio file (.wav file) from the computer to the root directory on a USB flash drive.

Recording Yourself Playing Along with the Accompaniment Song

1. Use the [] [+] controllers to select the accompaniment you have prepared.

2. Press the button below ([F1]) and the button below > ([F2]) to start recording and playback.

3. Play the drums.

4. After you finish playing, press the button below ([F1]) to stop recording.

Audio file requirements: 16-bit, 44.1 kHz, stereo, wav format

NOTE Some of the audio files may not play back even when the above requirements are met.

The DTX-PROX does not recognize the audio file if it is in a folder.

NOTE Pressing the button below ([F2]) stops accompaniment playback, but recording continues.

or

DTX-PROX Owners Manual

Connecting a PA System

Basic Guide

When sending the DTX-PROX sounds to a mixer for live performance or other applications, connect the PA system as fol- lows:

[INDIVIDUAL OUTPUT] jacks (1/2 to 7/8) Output the sound of each instrument, such as snare and kick.

Stereo standard phone jack (UNBALANCED) Up to 8 mono outputs (or 4 stereo outputs) Any sounds (such as pad sounds, and click) can be assigned independently to the outputs

To split one stereo output into two mono outputs, use a commercially available Y-cable. The routing settings can be changed. For more information, refer to the Reference Manual (PDF).

Connecting a PA System

PA mixer

DTX-PROX

INDIVIDUAL OUTPUT

Example connection

49DTX-PROX Owners Manual

50

Using Live Sets

Basic Guide

A Live Set is a combination of the Kit, tempo, audio files and other settings sequenced in the order you like. For example, you can create a chain of Kits in the order of a performance set list when playing live, or arrange a series of audio files in the order of difficulty level for use in your daily practice. With the DTX-PROX, you can save up to 10 Live Sets, and use them anytime during your performance.

Creating a Live Set You can create a Live Set by registering the combination for each Step. For more information, refer to the Reference Manual (PDF).

Using Live Sets

Live set 1 Live set 10 Up to 20

steps

etc.

Up to 20 steps

etc.

Kit

Tempo

Audio file

Step1

Kit

Tempo

Audio file

Step1

DTX-PROX Owners Manual

Application Guide

You can connect add-ons (sold separately) and external devices to the DTX-PROX to access more functions of the DTX- PROX.

About the Trigger Input Jacks Trigger Input jacks are used for connecting pads. The [qSNARE] to [!4] jacks on the rear panel accept up to 14 pads. For more information on the types of pads you can use, see Playing the Pads (page 27).

For information on the voice assignment of trigger inputs, refer to the Data List (PDF).

For more information on the separately-sold accessories that can be connected to each trigger input jack, refer to the Pad Module Compatibility table available on the website shown below.

Yamaha Downloads: https://download.yamaha.com/

* Yamaha Corporation reserves the right to modify this URL at any time without prior notice.

Connecting Separately Sold Add-ons and External Devices

CONTROL, !1HI-HAT For connecting the HH65 hi-hat controller, RHH135 real hi-hat pad and others.

!0CRASH2, oCRASH1, iRIDE Supports single-piezo pads (3-zone).

!4, qSNARE Supports multi-piezo pads and single- piezo pads (3-zone).

To connect additional toms and other pads, use the [!4] jack.

!2KICK/!3, yTOM3/u, rTOM2/t, wTOM1/e Supports multi-piezo pads. Single-piezo pads connected to these jacks function as 1-zone pads.

When kick pads such as the KP90 are connected to these jacks, you can use the input jack on the back of the kick pad to add another pad.

You can connect two pads to one jack using a commercially available Y-cable. (In this condition, all pads function as single-piezo 1-zone pads.)

To connect two pads to a jack, you may need to set the trigger input to use it sepa- rately (TRIGGER/SETTING/Input mode). For more information, refer to the Reference Manual (PDF).

Stereo phone plug Mono phone jack

Mono phone jack Y-cable

51DTX-PROX Owners Manual

52

Connecting Separately Sold Add-ons and External Devices

Application Guide

Integrating Separately Sold Accessories You can expand your electronic drum kit with various accessories* for an even more enjoyable drumming experience. (*: sold separately)

Adding a tom to the [!4] jack

1. Turn off the drum trigger module.

2. Connect the XP125T-X to the [!4] jack.

3. Turn on the drum trigger module.

4. Choose the correct pad type for the XP125T-X. (TRIGGER/SETTING/Pad Type)

Adding a cymbal to the [wTOM1/e] jack

By attaching a commercially available Y-cable to the [wTOM1/e] jack, you can connect an additional cymbal. In that condition, those two pads connected to the same jack function as single-piezo 1-zone pads.)

1. Turn off the drum trigger module.

2. Connect a commercially available Y-cable and a pad to the [wTOM1/e] jack.

3. Turn on the drum trigger module.

4. Set the Pad Type to PCY95AT. To split the trigger input, set the Input Mode to sepa- rate. (TRIGGER/SETTING/input mode)

The following describes how to connect a XP125T-X or a PCY95AT. For the information on the compatibility of other pads, refer to the Pad Module compatibility table (PDF). https://download.yamaha.com/

OUTPUT

to DTX-PROX

XP125T-X

Stereo standard phone cable (such as the included cable)

to DTX-PROX

XP105T-X

OUTPUT PCY95AT

Y-cable

Stereo standard phone cable (such as the included cable)

DTX-PROX Owners Manual

Connecting Separately Sold Add-ons and External Devices

Application Guide

Integrating Electronic & Acoustic Drums The following describes a couple of examples of how you can integrate electronic and acoustic drums.

Adding Pads to an Acoustic Drum Set

You can easily add a pad such as the XP125SD-X to an acoustic drum set. Set the proper Pad Type for the con- nected pad (TRIGGER/SETTING/Pad Type).

Typical setup

Playing the DTX-PROX Using Acoustic Drums

You can attach a DT50K or DT50S Drum Trigger to the bass drum or the snare drum and connect to the [!2KICK/ !3] jack or the [qSNARE] jack on the DTX-PROX to send trigger signals to your drum trigger module whenever the drum is struck. After connecting cables, set the pad type parameter. (TRIGGER/SETTING/Pad Type)

Typical setup (for attaching the Drum Triggers to the snare and the bass drum)

XP125SD-X

DTX-PROX KP128

For more information on how to attach the Drum Trigger, refer to the DT50S/DT50K Owners Manual.

DT50S

DT50K

to DTX-PROX

DT50S

DTX-PROX

DT50K

53DTX-PROX Owners Manual

54

Connecting Separately Sold Add-ons and External Devices

Application Guide

Connecting a Computer You can connect the DTX-PROX to a computer and use DAW (Digital Audio Workstation) software such as the included Cubase AI to record your performance, edit, or mix audio.

For more information on how to connect a computer, refer to the Reference Manual (PDF). For more information on how to use the DAW software, refer to the Owners Manual for your DAW software.

Precautions when using the [USB TO HOST] terminal When connecting the computer to the [USB TO HOST] terminal, make sure to observe the following points to avoid freezing the computer and corrupting or losing the data.

If the computer or the instrument freezes, restart the application software or the computer OS, or turn the power to the instrument off then on again.

NOTICE Use an AB type USB cable of less than 3 meters. USB 3.0 cables cannot be used.

Execute the following before turning the power to the instrument on/off or plugging/unplugging the USB cable to/ from the [USB TO HOST] terminal. - Quit any open application software on the computer.

- Make sure that data is not being transmitted from the instrument.

While the computer is connected to the instrument, you should wait for six seconds or more between these oper- ations: (1) when turning the power of the instrument off then on again, or (2) when alternately connecting/discon- necting the USB cable.

DTX-PROX Owners Manual

Reference

Message List

Message Description

Are you sure? Confirms whether or not you want to run the specified operation.

Auto power off disabled. Appears when the [MENU] button is held down while turning on the power informing the user that the Auto Power Off function is dis- abled.

Backup error. Appears when writing data to the DTX-PROX has failed. If data was not be properly saved when turning off the unit, this mes- sage appears the next time the power is turned on. After the error message appears, the Factory Reset is carried out automatically.

Bluetooth pairing.... Waiting for Bluetooth devices to pair. (page 24)

Canceled. Appears when the cancel operation is complete.

Cant process. The DTX-PROX cannot process a requested operation.

Completed. Appears when a Kit Store, File Load/Save, Job, or other function is complete.

Connecting USB device... Appears when connecting to a USB device.

Excessive demand for USB power. Power consumption of the USB device exceeds the specified value.

Factory Reset initializing... Appears on startup if you did a factory reset.

File already exists. A file with the same name already exists.

File not found. The selected file type was not found.

Illegal file. Appears when loading a file and the DTX-PROX cannot handle the target file or does not support the audio file.

Incompatible USB device. Appears when an unsupported USB device is connected to the [USB TO DEVICE] terminal.

Invalid USB device. The USB device is faulty. Format the USB device again.

Keybank full. Appears when the total number of keybanks for waveforms have exceeded the maximum capacity.

No data. Appears when the target data does not exist when using the Recorder or using Wav-related parameters under Job.

No response from USB device. There is no response from the USB device.

Now importing... Appears when importing a .wav file.

Now loading... Appears when loading a file.

Now processing... Appears when running the Kit Store or Job operation. Appears during post-processing after canceling the File Load or File Save operation.

Now saving... Appears when saving a file.

Overwrite? Appears when saving a file to the USB device and a file with the same name already exists in the USB device. Appears when attempting to rerun the Store User Kit operation for the Kit previously saved.

55DTX-PROX Owners Manual

56

Message List

Reference

Please stop recorder. Appears when performing an operation that exits the Recorder during recorder playback or recording. Stop the Recorder and try again.

Recording time limit exceeded. Appears when the recorder has reached the time limit. Recording time is about 1 minute 30 seconds with internal memory, and about 90 minutes with a USB flash drive. This message also appears when the USB flash drive has reached its capacity during recording.

Read only file. Appears when a read-only file is selected during a file operation.

Sample is too long. Sample is too long and cannot be loaded.

Sample is too short. Sample is too short and cannot be loaded.

Song is too long. The song file is too large and cannot be loaded.

USB connection terminated. Appears if connection with the USB device was interrupted by an abnormal electric current. Disconnect the USB device and press the button below OK.

USB devices transfer speed too slow. Appears when the transfer speed to the USB device is insufficient. For information on devices that have been tested and confirmed to work properly with the DTX-PROX, refer to the Compatible USB Device List on the Yamaha web site.

USB device full. Appears when the USB device is full and files cannot be saved on it. Use a new USB device or make space by erasing unnecessary files from the full device.

USB device not ready. Appears if the USB device is not properly connected to the DTX- PROX.

USB device read/write error. Appears if an error occurred while reading or writing data to the USB device.

USB device write protected. Appears if the USB device is write-protected.

USB transmission error. Appears if an error occurred while communicating with the USB device.

User Voice full. Appears when the total number of User voices have exceeded the maximum capacity.

Waveform full. Appears when the total number of waveforms have exceeded the maximum capacity.

Wave memory error. Appears when loading data to the Wave memory has failed. When the Wave data was not saved properly, this message appears the next time the DTX-PROX is turned ON. After this message appears, the recovery process starts automatically.

Wave memory full. Appears if the WAVE memory is full and operations such as Import, Job, or Load cannot be carried out.

Message Description

DTX-PROX Owners Manual

Troubleshooting

Reference

For more troubleshooting tips, refer to the Reference Manual (PDF). See page 7 for details on downloading this manual.

Troubleshooting

Symptom Possible cause Solution Reference

page

No sound

Out of balance

No sound The cable is not properly connected

Ensure that the DTX-PROX is properly connected to headphones or an external audio system, such as an amplifier and/ or speakers.

Ensure that the cables you are using are in good condition.

page 12 page 13 page 16

The volume or level settings are improper

The headphone volume is not turned up

The metronome volume is not turned up

Check the following:

Volume controllers on amplifiers and/or speakers connected to the DTX-PROX.

Sliders ([OUTPUT], [PHONES]) on the DTX-PROX top panel.

LED rotary faders Volume for the metronome (Click)

([CLICK] slider). The trigger output level of any pads with

a dial allowing this to be adjusted.

page 10 page 13

Poor volume balance Poor volume balance between each of the pads

Ensure that the LED rotary faders have been set appropriately.

page 35

Poor volume balance between the external audio device and the DTX-PROX

Individually adjust the output volumes of the DTX-PROX and the external audio devices.

Adjust the volume with the [AUDIO] slider.

page 10 page 13 page 24

Poor EQ balance Poor EQ balance Adjust the Phones EQ and the Master EQ.

page 16 page 39

Pads with position sens- ing do not produce sounds properly

Ensure that the Pad Type and trigger parameters have been set correctly. (For more information, refer to the Refer- ence Manual (PDF).)

Check the orientation of the cymbal pad. When this is not set properly, the cymbal pad may not be fully functional.

Make sure to connect the pad to the proper jack that supports position sens- ing.

page 27

Assembly Manual

Headphone volume is too low

Adjust the values in MENU/Utility/Out- put Gain.

Use one headphone at a time. Using two at once may reduce the output level.

Reference Manual (PDF)

page 16

57DTX-PROX Owners Manual

58

Troubleshooting

Reference

Having difficul- ties during perfo- mance

Cymbal/Hi-hat sounds are too soft

The DTX-PROX pro- duces sound but the sensitivity (i.e., volume) is too low.

Orientation of the cymbal pad is incorrect

Shaft on the Hi-hat pad is loose

Extra felt is attached

The pad type or trigger parameter setting is incorrect

LED rotary fader is set at the minimum level

The level settings for the pad are improper

Check the orientation of the cymbal pad. When it is improper, the cymbal pad may not be fully functional.

The shaft on the hi-hat stand may come loose during use and cause the hi-hat pad to rotate. If this happens, the pad may not function properly. To avoid the problem, we recommend that you tighten the shaft and check the position of the hi-hat pad on a regular basis.

Putting extra felt under the cymbal pad may result in lower volume.

Ensure that the Pad Type parameter is set correctly. (A suitable cymbal-pad type must be selected for the pad being used. (For more information, refer to the Reference Manual (PDF).)

The trigger output level of any pads with a dial allow this to be adjusted.

page 27

Assembly Manual

Ensure that the LED rotary fader for the pad for which a sound is not being pro- duced is set high enough.

page 35

Sound is produced with- out striking the pad

Sound is produced by a pad that was not struck (Crosstalk is occurring)

For more information, refer to the Refer- ence Manual (PDF).

Reference Manual (PDF)

Cannot choke

Cannot mute

Check the orientation of the cymbal pad. When the orientation of the pad is improper, the cymbal pad may not func- tion fully.

page 27

Assembly Manual

Foot closed hi-hat sounds cannot be played

It is difficult to produce closed hi-hat sounds

Shaft on the Hi-hat pad is loose

Extra felt is attached

LED rotary fader is set at the minimum level

The level settings for the pad are improper

Make sure that you are fully and firmly operating the hi-hat pedal.

Ensure that the foot controller is cor- rectly connected to the [CONTROL] jack.

Putting extra felt under the cymbal pad may result in lower volume.

Assembly Manual

Ensure that the LED rotary fader for the pad for which a sound is not being pro- duced is set high enough.

page 35

Pads with position sens- ing do not produce sounds properly

Ensure that the Pad Type and trigger parameters have been set correctly. (For more information, refer to the Refer- ence Manual (PDF).)

Check the orientation of the cymbal pad. When this is not set properly, the cymbal pad may not be fully functional.

Make sure to connect the pad to the proper jack that supports position sens- ing.

page 27

Assembly Manual

Symptom Possible cause Solution Reference

page

DTX-PROX Owners Manual

Troubleshooting

Reference

Settings The drum module does not store its settings

The drum module automatically stores its system settings whenever you turn it off using the [ ] (Standby/On) button.

Do not turn off the drum module by unplugging the AC adaptor. This will prevent it from storing the system set- tings.

User settings for kits, click sets, and trig- gers must be stored manually.

page 18 page 15 page 40

Data cannot be saved on a USB flash drive

USB 1.1 compatible flash drives cannot be used on the DTX-PROX.

Ensure that the USB flash drive in ques- tion has been formatted using the DTX- PROX.

Ensure that the USB flash drive in ques- tion has not been write-protected.

Ensure that there is sufficient free space on the USB flash drive to save the data. (For more information, refer to the Ref- erence Manual (PDF).)

Reference Manual (PDF)

Cannot send data to or from the smart device

Check the connection. For more informa- tion, refer to the iPhone/iPad Connection Manual or Smart Device Connection Manual for Android.

page 23

The Bluetooth-equipped smart device cannot be paired with nor con- nected to the instrument.

Check the Bluetooth function of the smart device is activated. To connect the smart device and the instrument via Bluetooth, both devices need to be func- tional.

The smart device and the instrument need to be paired (page 24).

In case there is a device (microwave oven, wireless LAN device, etc.) that outputs signals in the 2.4 GHz fre- quency band nearby, move this instru- ment away from the device that is emitting radio-frequency signals.

page 24

Power turns off unex- pectedly

Disable the Auto Power-Off function. page 19

The DTX-PROX does not receive any switch or trigger signals at all

I want to reset the DTX- PROX to the factory default

Use the Factory Reset to restore the set- tings to the factory defaults.

page 20

Symptom Possible cause Solution Reference

page

59DTX-PROX Owners Manual

60

Specifications

Reference

The contents of this manual apply to the latest specifications as of the publishing date. To obtain the latest manual, access the Yamaha website then download the manual file. Since specifications, equipment or separately sold accessories may not be the same in every locale, please check with your Yamaha dealer.

Specifications

Tone generator Type AWM2

Maximum polyphony 256 notes

Effect units For each Inst EQ / Comp / Transient / Insertion (*1)

For each Kit Ambience / Effect 1 / Effect 2 Master Comp / Master Effect

For overall Master EQ / Phones EQ

(*1) Insertion effects can be used only for specific Inst.

Kits Quantity Preset: more than 40 kits User: 200 kits

Number of voices Drum/Percussion: more than 400

Metronome User click sets 30

Tempo 30 to 300 BPM; tap tempo supported

Time signatures 1/4 to 16/4, 1/8 to 16/8, and 1/16 to 16/16

Subdivisions Accents, quarter notes, eighth notes, sixteenth notes, and eight-note triplets

Others Individual click volume control, wav import, timer

Training Types 10

Training Songs Preset: 37 songs User: 1 song

Audio files Import limit 1,000 files

Maximum loadable sample time

50 minutes 40 seconds (44.1 kHz, 16 bit, mono) 25 minutes 20 seconds (44.1 kHz, 16 bit, stereo)

Sampling format WAV

Recorder Recording time Internal memory maximum of 90 seconds

USB flash drive maximum of 90 minutes per file

Format Record/playback WAV (44.1 kHz, 16 bit, stereo)

Display Full Dot LCD (12864 dot)

Connectivity DC IN DC IN (+12V)

Headphones Headphones (standard stereo phone jack 1, stereo mini jack 1)

AUX IN AUX IN (stereo mini jack 1, stereo standard phone jack 1)

Output OUTPUT L/MONO, R (standard phone jack, one for each) INDIVIDUAL OUTPUT 1/2, 3/4, 5/6, 7/8 (stereo standard phone jack, one for each)

USB USB TO DEVICE USB TO HOST

MIDI MIDI OUT 1 MIDI IN 1

Trigger Input Jacks 10 (standard stereo phone jack, not including the HI-HAT CONTROL jack)

Maximum number of pads to be connected (when Y-cable is used)

14

Bluetooth (May not have this functional- ity depending on the country in which you purchased the product.)

Supported profile A2DP

Compatible codec SBC

Bluetooth version 4.1

Wireless output Bluetooth class 2

Maximum communication distance Approx. 10 m

Radio Frequency (Operational Frequency) 24022480 MHz

Maximum output power (EIRP) +4 dBm

Type of modulation GFSK, /4 DQPSK, 8DPSK

Power consumption 13 W

Dimensions 342 (W) mm 196 (D) mm 66 (H) mm (13-7/16 in 7-11/16 in 2-5/8 in)

Weight 2.0 kg (4 lb 7 oz)

Included Accessories AC adaptor (PA-150 or an equivalent recommended by Yamaha (Output : DC 12V, 1.5 A))(*2), Owners Manual (this document), module holder, module holder wing bolts ( 4), Cubase AI Download Information

(*2) May not be included depending on your area. Check with your Yamaha dealer.

DTX-PROX Owners Manual

61DTX-PROX Owners Manual

Index

Reference

Symbols [][+] controllers................................11 [][+] knob ........................................11 [] button ..........................................11 [+] button ..........................................11

Numerics 1-zone pads..................................... 27 3-zone pads .................................... 27

A AC adaptor ...................................... 15 Accompaniment .............................. 48 Acoustic Drums............................... 53 Ambience ........................................ 26 [AMBIENCE] knob .................... 10, 33 Audio files (.wav) ............................. 37 [AUDIO] slider ..................................11 [AUDITION] button ...........................11 Auto Power-Off ................................ 19 [AUX IN] (auxiliary input) jack ... 12, 13 [AUX IN] slider..................................11

B Bell shots ........................................ 30 Bluetooth................................4, 11, 24 Bow shots.................................. 29, 30

C Choking........................................... 30 Click .......................................... 42, 43 [CLICK] button..................................11 CLICK mode ................................... 10 [CLICK] slider ...................................11 Click Tempo Display .........................11 Closed rim shots ............................. 28 Comp............................................... 26 [COMP] knob ............................ 10, 33 Computer ........................................ 54 Cord hook........................................ 13 Cross stick setting ........................... 10 Cross sticking.................................. 28 CUSTM (Custom)............................ 10 Custom settings............................... 34 Cymbal Size .................................... 34 Cymbals .......................................... 30

D DAW (Digital Audio Workstation)

software ....................................... 54 DC IN jack ....................................... 13 Display ............................................ 10 Drum set ................................... 26, 34

E Edge shots ................................ 29, 30 Effect ................................... 26, 33, 34 [EFFECT] knob ......................... 10, 33 EFFECT screen .............................. 10 [EXIT] button ....................................11

F Factory Reset.................................. 20 Fader Select knob ........................... 10 Foot-close sounds........................... 29 Front Panel...................................... 12 Function Buttons 13

([F1], [F2], [F3])............................ 10 FX (Effects) ..................................... 10

H Head shots...................................... 28 Headphones.................................... 16 Hi-hat clutch positions..................... 34 Hi-hat splash sounds ...................... 29 Hi-hats............................................. 29

I [INDIVIDUAL OUTPUT] jacks ... 13, 49 INST................................................ 10 Inst ............................................ 26, 34

K Kit.............................................. 26, 32 KIT mode ........................................ 10 KIT MODIFIER knobs ..................... 10 KIT screen................................. 10, 32

L LED Rotary Faders ......................... 10 LIVE SET mode .............................. 10 Live Sets ......................................... 50

M [MENU] button..................................11 Metronome................................ 42, 43 [MIDI IN] connector ......................... 13 [MIDI OUT] connector ..................... 13 MIXER............................................. 10 Mixer ......................................... 34, 35 Mode Select knob ........................... 10 Monaural pads ................................ 27 MUFFL (Muffling) ............................ 10 Muffling............................................ 34 Multi Piezo ...................................... 27 Multi-piezo pads.............................. 51 Muting ....................................... 31, 34

O Open rim shots ............................... 28 Open/Close ..................................... 29 OUTPUT [R]/[L/MONO] jacks ......... 13 [OUTPUT] slider...............................11

P PA.................................................... 49 [PAD SELECT] button ......................11 Pads................................................ 27 Paring.............................................. 24 [PHONES] (Headphone) jack ......... 12 [PHONES] slider ..............................11 Position sensing................... 27, 28, 30

R Rear Panel ...................................... 13 RECORDER mode ..........................10

S Separately Sold Accessories........... 52 Single Piezo .................................... 27 Single-piezo pads ........................... 51 Smart Devices................................. 23 Snare .............................................. 28 [ ] (Standby/On) switch..................11 Step................................................. 50 [STORE] button ................................11 Sustain length of the cymbal........... 34

T Tap Tempo....................................... 43 Tempo ............................................. 42 [TEMPO] knob .................................11 Tom ................................................. 28 Top Panel .........................................10 Trigger Input jacks..................... 13, 51 TRIGGER mode...............................10 Trigger Settings ............................... 45 Trigger Setup Wizard....................... 17 TUNING ...........................................10 Tunings............................................ 34

U [USB TO DEVICE] terminal....... 13, 21 [USB TO HOST] terminal .......... 13, 54

W .wav................................................. 37

Y Y-cable ............................................ 51

Z Zones .............................................. 27

Index

6

Drums Limited Warranty LIMITED WARRANTY ON YAMAHA DRUMS, HARDWARE AND ACCESSORY PRODUCTS

Thank you for selecting a YAMAHA product. YAMAHA products are designed and manufactured to provide a high level of defect-free performance. Yamaha Corporation of America (YAMAHA) is proud of the experience and craftsmanship that goes into each and every YAMAHA product. YAMAHA sells its products through a network of reputable, specially authorized dealers and is pleased to offer you, the Original Owner, the following Limited Warranty, which applies only to products that have been (1) directly purchased from YAMAHAs authorized dealers in the fifty states of the USA and District of Columbia (the Warranted Area) and (2) used exclusively in the Warranted Area. YAMAHA suggests that you read the Limited Warranty thoroughly, and invites you to contact your authorized YAMAHA dealer or YAMAHA Customer Service if you have any questions.

THIS WARRANTY COVERS THE LISTED PRODUCTS AGAINST DEFECTS IN MATERIALS OR WORKMANSHIP. Warranty Term

Duration of Warranty from Date of Type of Product Purchase by or for the Original Owner

Acoustic Drum Shells, Finish, Drum Hardware, Freestanding Hardware, Pedals, Hardware Accessories 5 Years Electronic Drums Modules, Pads, Accessories, Hardware, Pedals 1 Year

Coverage: YAMAHA will, at its option, repair or replace the product covered by this warranty if it becomes defective, malfunctions or otherwise fails to conform with this warranty under normal use and service during the term of this warranty, without charge for labor or materials. Repairs may be performed using new or refurbished parts that meet or exceed YAMAHA specifications for new parts. If YAMAHA elects to replace the product, the replacement may be a reconditioned unit. You will be responsible for any installation or removal charges and for any initial shipping charges if the product(s) must be shipped for warranty service. However, YAMAHA will pay the return shipping charges to any destination within the USA if the repairs are covered by the warranty. This warranty does not cover (a) damage, deterioration or malfunction resulting from accident, negligence, misuse, abuse, improper installation or operation or failure to follow instructions according to the Owners Manual for this product; any shipment of the product (claims must be presented to the carrier); repair or attempted repair by anyone other than YAMAHA or an authorized YAMAHA Service Center; (b) any unit which has been altered or on which the serial number has been defaced, modified or removed; (c) normal wear and any periodic maintenance; (d) deterioration due to perspiration, corrosive atmosphere or other external causes such as extremes in temperature or humidity; (e) damages attributable to power line surge or related electrical abnormalities, lightning damage or acts of God; or (f) RFI/EMI (Interference/noise) caused by improper grounding or the improper use of either certified or uncertified equipment, if applicable. Any evidence of alteration, erasing or forgery of proof-of-purchase documents will cause this warranty to be void. This warranty covers only the Original Owner and is not transferable.

In Order to Obtain Warranty Service: Warranty service will only be provided for defective products within the Warranted Area. Contact your local authorized YAMAHA dealer who will advise you of the procedures to be followed. If this is not successful, contact YAMAHA at the address, telephone number or website shown below. YAMAHA may request that you send the defective product to a local authorized YAMAHA Servicer or authorize return of the defective product to YAMAHA for repair. If you are uncertain as to whether a dealer has been authorized by YAMAHA, please contact YAMAHAs Service Department at the number shown below, or check Yamahas website at http://usa.yamaha.com. Product(s) shipped for service should be packed securely and must be accompanied by a detailed explanation of the problem(s) requiring service, together with the original or a machine reproduction of the bill of sale or other dated, proof-of-purchase document describing the product, as evidence of warranty coverage. Should any product submitted for warranty service be found ineligible therefore, an estimate of repair cost will be furnished and the repair will be accomplished only if requested by you and upon receipt of payment or acceptable arrangement for payment.

Limitation of Implied Warranties and Exclusion of Damages: ANY IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED IN DURATION TO THE APPLICABLE PERIOD OF TIME SET FORTH ABOVE. YAMAHA SHALL NOT BE RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OR FOR DAMAGES BASED UPON INCONVENIENCE, LOSS OF USE, DAMAGE TO ANY OTHER EQUIPMENT OR OTHER ITEMS AT THE SITE OF USE OR INTERRUPTION OF PERFORMANCES OR ANY CONSEQUENCES. YAMAHAS LIABILITY FOR ANY DEFECTIVE PRODUCT IS LIMITED TO REPAIR OR REPLACEMENT OF THE PRODUCT, AT YAMAHAS OPTION. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. This is the only express warranty applicable to the product specified herein; Yamaha neither assumes nor authorizes anyone to assume for it any other express warranty.

If you have any questions about service received or if you need assistance in locating an authorized YAMAHA Servicer, please contact:

CUSTOMER SERVICE Yamaha Corporation of America

6600 Orangethorpe Avenue, Buena Park, California 90620-1373 Telephone: 800-854-1569 http://usa.yamaha.com

Do not return any product to the above address without a written Return Authorization issued by YAMAHA.

2 DTX-PROX Owners Manual

63DTX-PROX Owners Manual

n 2 0

For details of products, please contact your nearest Yamaha representative or the authorized distributor listed below. Pour plus de dtails sur les produits, veuillez-vous adresser Yamaha ou au distributeur le plus proche de vous figurant dans la liste suivante.

Die Einzelheiten zu Produkten sind bei Ihrer unten aufgefhrten Niederlassung und bei Yamaha Vertragshndlern in den jeweiligen Bestimmungslndern erhltlich. Para detalles sobre productos, contacte su tienda Yamaha ms cercana o el distribuidor autorizado que se lista debajo.

CANADA Yamaha Canada Music Ltd. 135 Milner Avenue, Toronto, Ontario M1S 3R1, Canada Tel: +1-416-298-1311

U.S.A. Yamaha Corporation of America 6600 Orangethorpe Avenue, Buena Park, CA 90620, U.S.A. Tel: +1-714-522-9011

MEXICO Yamaha de Mxico, S.A. de C.V. Av. Insurgentes Sur 1647 Piso 9, Col. San Jos Insurgentes, Delegacin Benito Jurez, CDMX, C.P. 03900, Mxico Tel: +52-55-5804-0600

BRAZIL Yamaha Musical do Brasil Ltda. Praa Professor Jos Lannes, 40-Cjs 21 e 22, Brooklin Paulista Novo CEP 04571-100 So Paulo SP, Brazil Tel: +55-11-3704-1377

ARGENTINA Yamaha Music Latin America, S.A., Sucursal Argentina Olga Cossettini 1553, Piso 4 Norte, Madero Este-C1107CEK, Buenos Aires, Argentina Tel: +54-11-4119-7000

PANAMA AND OTHER LATIN AMERICAN REGIONS/ CARIBBEAN REGIONS

Yamaha Music Latin America, S.A. Edificio Torre Davivienda, Piso: 20 Avenida Balboa, Marbella, Corregimiento de Bella Vista, Ciudad de Panam, Rep. de Panam Tel: +507-269-5311

THE UNITED KINGDOM/IRELAND Yamaha Music Europe GmbH (UK) Sherbourne Drive, Tilbrook, Milton Keynes, MK7 8BL, U.K. Tel: +44-1908-366700

GERMANY Yamaha Music Europe GmbH Siemensstrasse 22-34, 25462 Rellingen, Germany Tel: +49-4101-303-0

SWITZERLAND/LIECHTENSTEIN Yamaha Music Europe GmbH, Branch Switzerland in Thalwil Seestrasse 18a, 8800 Thalwil, Switzerland Tel: +41-44-3878080

AUSTRIA/CROATIA/CZECH REPUBLIC/ HUNGARY/ROMANIA/SLOVAKIA/SLOVENIA

Yamaha Music Europe GmbH, Branch Austria Schleiergasse 20, 1100 Wien, Austria Tel: +43-1-60203900

POLAND Yamaha Music Europe Sp.z o.o. Oddzia w Polsce ul. Wielicka 52, 02-657 Warszawa, Poland Tel: +48-22-880-08-88

BULGARIA Dinacord Bulgaria LTD. Bul.Iskarsko Schose 7 Targowski Zentar Ewropa 1528 Sofia, Bulgaria Tel: +359-2-978-20-25

MALTA Olimpus Music Ltd. Valletta Road, Mosta MST9010, Malta Tel: +356-2133-2093

NETHERLANDS/BELGIUM/ LUXEMBOURG

Yamaha Music Europe, Branch Benelux Clarissenhof 5b, 4133 AB Vianen, The Netherlands Tel: +31-347-358040

FRANCE Yamaha Music Europe 7 rue Ambroise Croizat, Zone d'activits de Pariest, 77183 Croissy-Beaubourg, France Tel: +33-1-6461-4000

ITALY Yamaha Music Europe GmbH, Branch Italy Via Tinelli N.67/69 20855 Gerno di Lesmo (MB), Italy Tel: +39-039-9065-1

SPAIN/PORTUGAL Yamaha Music Europe GmbH Ibrica, Sucursal en Espaa Ctra. de la Corua km. 17,200, 28231 Las Rozas de Madrid, Spain Tel: +34-91-639-88-88

GREECE Philippos Nakas S.A. The Music House 19th klm. Leof. Lavriou 190 02 Peania Attiki, Greece Tel: +30-210-6686260

SWEDEN Yamaha Music Europe GmbH Germany Filial Scandinavia JA Wettergrensgata 1, 400 43 Gteborg, Sweden Tel: +46-31-89-34-00

DENMARK Yamaha Music Denmark, Fillial of Yamaha Music Europe GmbH, Tyskland Generatorvej 8C, ST. TH., 2860 Sborg, Denmark Tel: +45-44-92-49-00

FINLAND F-Musiikki Oy Antaksentie 4 FI-01510 Vantaa, Finland Tel: +358 (0)96185111

NORWAY Yamaha Music Europe GmbH Germany - Norwegian Branch Grini Nringspark 1, 1332 sters, Norway Tel: +47-6716-7800

ICELAND Hljodfaerahusid Ehf. Sidumula 20 IS-108 Reykjavik, Iceland Tel: +354-525-5050

CYPRUS Nakas Music Cyprus Ltd. Nikis Ave 2k 1086 Nicosia Tel: + 357-22-511080 Major Music Center 21 Ali Riza Ave. Ortakoy P.O.Box 475 Lefkoa, Cyprus Tel: (392) 227 9213

RUSSIA Yamaha Music (Russia) LLC. Room 37, entrance 7, bld. 7, Kievskaya street, Moscow, 121059, Russia Tel: +7-495-626-5005

OTHER EUROPEAN REGIONS Yamaha Music Europe GmbH Siemensstrasse 22-34, 25462 Rellingen, Germany Tel: +49-4101-303-0

Yamaha Music Gulf FZE JAFZA-16, Office 512, P.O.Box 17328, Jebel Ali FZE, Dubai, UAE Tel: +971-4-801-1500

TURKEY Yamaha Music Europe GmbH Merkezi Almanya Trkiye stanbul ubesi Mor Sumbul Sokak Varyap Meridian Business 1.Blok No:1 113-114-115 Bati Atasehir Istanbul, Turkey Tel: +90-216-275-7960

ISRAEL RBX International Co., Ltd. P.O Box 10245, Petach-Tikva, 49002 Tel: (972) 3-925-6900

OTHER REGIONS Yamaha Music Gulf FZE JAFZA-16, Office 512, P.O.Box 17328, Jebel Ali FZE, Dubai, UAE Tel: +971-4-801-1500

THE PEOPLES REPUBLIC OF CHINA Yamaha Music & Electronics (China) Co., Ltd. 2F, Yunhedasha, 1818 Xinzha-lu, Jingan-qu, Shanghai, China Tel: +86-400-051-7700

HONG KONG Tom Lee Music Co., Ltd. 11/F., Silvercord Tower 1, 30 Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel: +852-2737-7688

INDIA Yamaha Music India Private Limited P-401, JMD Megapolis, Sector-48, Sohna Road, Gurugram-122018, Haryana, India Tel: +91-124-485-3300

INDONESIA PT Yamaha Musik Indonesia Distributor Yamaha Music Center Bldg. Jalan Jend. Gatot Subroto Kav. 4, Jakarta 12930, Indonesia Tel: +62-21-520-2577

KOREA Yamaha Music Korea Ltd. 11F, Prudential Tower, 298, Gangnam-daero, Gangnam-gu, Seoul, 06253, Korea Tel: +82-2-3467-3300

MALAYSIA Yamaha Music (Malaysia) Sdn. Bhd. No.8, Jalan Perbandaran, Kelana Jaya, 47301 Petaling Jaya, Selangor, Malaysia Tel: +60-3-78030900

SINGAPORE Yamaha Music (Asia) Private Limited Block 202 Hougang Street 21, #02-00, Singapore 530202, Singapore Tel: +65-6740-9200

TAIWAN Yamaha Music & Electronics Taiwan Co., Ltd. 2F., No.1, Yuandong Rd., Banqiao Dist., New Taipei City 22063, Taiwan (R.O.C.) Tel: +886-2-7741-8888

THAILAND Siam Music Yamaha Co., Ltd. 3, 4, 15, 16th Fl., Siam Motors Building, 891/1 Rama 1 Road, Wangmai, Pathumwan, Bangkok 10330, Thailand Tel: +66-2215-2622

VIETNAM Yamaha Music Vietnam Company Limited 15th Floor, Nam A Bank Tower, 201-203 Cach Mang Thang Tam St., Ward 4, Dist.3, Ho Chi Minh City, Vietnam Tel: +84-28-3818-1122

OTHER ASIAN REGIONS https://asia-latinamerica-mea.yamaha.com/index.html

AUSTRALIA Yamaha Music Australia Pty. Ltd. Level 1, 80 Market Street, South Melbourne, VIC 3205 Australia Tel: +61-3-9693-5111

NEW ZEALAND Music Works LTD P.O.BOX 6246 Wellesley, Auckland 4680, New Zealand Tel: +64-9-634-0099

REGIONS AND TRUST TERRITORIES IN PACIFIC OCEAN

https://asia-latinamerica-mea.yamaha.com/index.html

NORTH AMERICA

CENTRAL & SOUTH AMERICA

EUROPE

AFRICA

MIDDLE EAST

ASIA

OCEANIA

DMI30Head Office/Manufacturer: Yamaha Corporation 10-1, Nakazawa-cho, Naka-ku, Hamamatsu, 430-8650, Japan Importer (European Union): Yamaha Music Europe GmbH Siemensstrasse 22-34, 25462 Rellingen, Germany Importer (United Kingdom): Yamaha Music Europe GmbH (UK) Sherbourne Drive, Tilbrook, Milton Keynes, MK7 8BL, United Kingdom

2020 Yamaha Corporatio Published 05/202

POMA*.*- **C

VGA5100

Manualsnet FAQs

If you want to find out how the DTX-PROX Yamaha works, you can view and download the Yamaha DTX-PROX Module Owner's Manual on the Manualsnet website.

Yes, we have the Owner's Manual for Yamaha DTX-PROX as well as other Yamaha manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Owner's Manual should include all the details that are needed to use a Yamaha DTX-PROX. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Yamaha DTX-PROX Module Owner's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Yamaha DTX-PROX Module Owner's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Yamaha DTX-PROX Module Owner's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Yamaha DTX-PROX Module Owner's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Yamaha DTX-PROX Module Owner's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.