Basic Set Assembly Manual This manual describes the standard assembly of the DTXPLORER Basic Set. After assembling the parts and connecting the cords as shown in Figure 1, the unit is ready to be turned on. * To assemble the unit, make sure you have the following three packages:
- RS40 (Rack System) - DTLK9 (Pad Set) - DTXPL (Trigger Module)
* Prepare beforehand a Phillips screwdriver, required in Mounting the pads and the trigger module on the rack system.
Before assembling the unit, lay a drum mat (sold separately). Before assembling the unit, lay a drum mat on the fl oor. Alternately, to prevent damaging your fl oor, lay the cardboard box of the included packages, etc. on the fl oor before assembling the two parts shown in the circles in Figure 1.
Figure 1: Unit Standard Assembly
q DTXPL (Drum Trigger Module) w TP65 (Drum Pad) e AC Adaptor r HH65 (Hi-Hat Controller) t PCY65 (Single-zone Cymbal Pad) y RS40 (Rack System) u KP65 (Kick Pad) i FP6110A (Foot Pedal)
Checking the contents of RS40
Open the RS40 (Rack System) package and confi rm the contents. Figure 2: RS40 (Rack System)
RS40 (1) Fastening Screw (2) *1
Cable Band (10) *2
Assembly Manual (1) *3 - RS40
*1 Use fastening screws to attach the trigger module in Mounting the pads and the trigger module on the rack system.
*2 Use cable bands to bind cables to pipes in Connecting to a power source. (Spare bands are included.) *3 Not this manual.
Assembling the Rack System
1 Take out the rack system from the package and remove all the cushioning. Remove the bubble wrap on the pipes while assembling the rack system.
The pipe ends may injure your fi ngers. Figure 3: Rack Assembly-1
* YAMAHA logo printed on pipe is facing the opposite side.
2 See Figure 3. Set up the rack system, with the YAMAHA logo label (a) on pipe facing the opposite side from you. Support the rack system with your right hand, and loosen the two knobs (b) and (c) on your left.
Figure 4: Rack Assembly-2
3 See Figure 4. Move the leg on your left (pipe ) in a clockwise direction until it is about 90 degrees from pipe with the YAMAHA logo. Tighten the two knobs loosened in step 2 and fi x the position of pipe .
4 See Figure 3 again. Loosen the knob (d) on your right. 5 See Figure 4 again. Move the leg on your right (pipe ) in a counterclockwise direction
until it is parallel with pipe . Tighten the knob loosened and fi x the position of pipe .
* In the following steps, loosen the knobs fi rst, decide the position of the pipe, and then tighten the knobs. Be careful not to tighten the knobs excessively. For better perfor- mance, make minor adjustments for each part of the unit with the knobs after the as- sembly is completed.
6 Loosen the two knobs (e) aligned at the base of pipe , and move pipe slightly outward in a counterclockwise direction. Tighten the two knobs loosened and fi x the position of pipe .
7 Loosen the two knobs ((f) on the middle left) aligned at the base of pipe . Move pipe slightly outward in a clockwise direction. Tighten the two knobs loosened and fi x the
position of pipe . 8 Loosen the two knobs ((g) on the upper left) aligned at the base of pipe , and move pipe
outward in a clockwise direction until it is about 45 degrees from pipe . Tighten the two knobs loosened and fi x the position of pipe .
9 Check that the entire rack system is stable. Hold the upper area of the vertical pipe and , and shake them. If the rack system is unstable, retighten the knobs tightened in steps 2
to 5. Figure 5: Rack Assembly-3
10 See Figure 5. Loosen the knobs of the cymbal holders and on the right and left (shown with on the opposite side of pipe ) and pull up the cymbal holders vertically to the height illustrated. Tighten the knobs loosened and fi x the positions of the cymbal holders.
11 Loosen the two knobs (h) aligned along the pipe with the Trigger Module attachment part .
Adjust the Trigger Module attachment part so the operating panel will face upward diagonally to your side when set. Hold the Trigger Module attachment part fi rmly and turn it gradually. Tighten the two knobs loosened and fi x the position of the Trigger Module attachment part .
PRECAUTIONS Before using, please read this assembly manual, and use this product in a safe and proper manner. Particularly in the case of children and young users, parents or an instructor should teach the children the proper manner in which to use the device.
WARNING If this symbol is ignored and the equipment is used improperly, fatal injury to persons or serious damage could occur.
Do not let small children assemble or set up this product by themselves, or they may be injured. Always assemble this product with adult supervision.
Be careful with the edges of the cymbal holders and the tom holders. The sharp holder ends may result in injury.
Be careful with the edges of the spurs attached to the base. The sharp spur ends may result in injury.
If this product is used with the rack system or a cymbal stand, make sure all bolts are tightened firmly. Also, when adjusting the height or angle, do not suddenly loosen the bolts. Loose bolts may result in the rack overturning or parts dropping, causing injury.
Always set the product on a flat and solid surface. Placement on a sloping, unstable surface or on steps may result in the product being unstable and subject to overturning.
When setting the product, please pay close attention to the handling and setting of cables. Carelessly placed cables may cause the user and others to trip and fall.
Do not alter the product. Doing so may result in injury or damage/deterioration to the product.
Do not sit or step on the rack. The rack may overturn or be damaged, resulting in injury.
Checking the contents of the Pad Set and the Trigger Module
Open the DTPK9 (Pad Set) and Trigger Module package and confi rm the contents. Figure 6: Pad Set DTLK9
TP65 (Drum Pad) (5) Clamp Bolt (5)
PCY65 (Cymbal Pad) (2) HH65 (Hi-Hat Controller) (1)
FP6110A (Foot Pedal) (1)
KP65 (Kick Pad) (1)
Drum Key (1)
9-channel snake cable (1)
Instruction Manual (4) - TP65/65S - PCY65/65S - HH65 - KP65
Figure 7: Trigger Module
DTXPL (1) AC Adaptor (1)
CAUTION If this symbol is ignored and the equipment is used improperly, there is a danger or injury to persons handling the equipment, and material damage could occur.
Watch your fingers when adjusting clamps. They may become pinched, resulting in injury.
Make sure you hold onto the plug, not the cable, when connecting or disconnecting the cable. Also, never place any heavy or sharp objects on the cable. Applying excessive force to the cable may result in damage to the cable, such as the wires being severed, etc.
Do not step on or place heavy objects on the product. It may result in damage.
Be careful around pipe ends, inside the pipe and screw ends. Metal shavings, etc. may injure your fingers.
Do not put your hands or feet under the foot pedal or foot switch. They may be pinched, resulting in injury.
Do not use or keep the product in places with extremely high temperature (places in direct sunlight, close to a heater, in a closed car, etc.) or high humidity (bathroom, outside on a rainy day, etc.). Doing so may result in deformation, discoloration, damage or deterioration.
When cleaning the product, do not use benzine, thinner or alcohol as it may result in discoloration or deformation. Please wipe with a soft cloth or a damp cloth that has been wrung out thoroughly. If the product is soiled or sticky, use a neutral detergent on a cloth then wipe with a damp cloth that has been wrung out thoroughly to remove any remaining detergent. Also pay close attention so as not to let the water and detergent come into contact with the cushions used in the product; doing so may result in deterioration.
Do not attach acoustic drums to the electronic drum rack. Clamps may be damaged and drums may drop, causing injury.
Continued on the next page (on the back side)
DTXPLORER_BS-set_en_0407.indd 1 2009/04/07 11:01:40
en
de
fr
sp