Contents

Yamaha CDC-S75 Mini Component System Owner's Manual PDF

1 of 54
1 of 54

Summary of Content for Yamaha CDC-S75 Mini Component System Owner's Manual PDF

Active Servo

Technology

CC-75 Natural Sound Mini Component System

Chane Mini de la srie Natural Sound Natural Sound Mini Komponenten-System Natural Sound Mini Komponent System

Sistema di Componenti Mini a Suono Naturale Sistema de Componentes con Sonido Natural

Natural Sound Mini Component Systeem

OWNERS MANUAL MODE DEMPLOI BEDIENUNGSANLEITUNG BRUKSANVISNING MANUALE DI ISTRUZIONI MANUAL DE INSTRUCCIONES GEBRUIKSAANWIJZING

CC-75: RX-S75 + CDC-S75 + KXW-S75 + NX-S75

Remote control transmitter Tlcommande Fernbedienung Fjrrkontroll Telecomando Controlador remoto Afstandbediening

Batteries (size AA, UM/SUM-3, R6, HP-7) Piles (format AA, UM/SUM-3, R6, HP-7) Batterien (Gre AA, UM/SUM-3, R6, HP-7) Batterier (Storl. AA, UM/SUM-3, R6, HP-7) Batterie (dimensioni AA, o UM/SUM-3, o R6, o HP-7) Pilas (tamao AA, tipo UM/SUM-3, R6, HP-7) Batterijen (maat AA, UM/SUM-3, R6, HP-7)

AM (MW/LW) loop antenna Cadre-antenne AM (PO/GO) MW/LW-Rahmenantenne MV/LV ramantenn Antenna ad anello per AM

(MW e LW) Antena de cuadro AM (OM/OL) AM (MW/LW) lusantenne

Indoor FM antenna Antenne intrieure FM UKW-Innenantenne FM inomhusantenn Antenna FM per interni Antena interior de FM FM binnenantenne

Speaker cords (for NX-S75) Cbles denceintes (pour les enceintes NX-S75) Lautsprecheranschlukabel (fr NX-S75) Hgtalarledningar (fr NX-S75) Cavi per gli altoparlanti (per lNX-S75) Cables de los altavoces (para el NX-S75) Luidsprekerdraden (voor NX-S75)

SUPPLIED ACCESSORIES After unpacking, check that the following parts are contained. ACCESSOIRES FOURNIS Aprs le dballage, vrifier que les pices suivantes sont incluses. MITGELIEFERTES ZUBEHR Nach dem Auspacken berprfen, ob die folgenden Teile vorhanden sind. MEDFLJANDE TILLBEHR Kontrollera efter det apparaten packats upp att fljande delar finns med. ACCESSORI IN DOTAZIONE Verificare che tutte le parti seguenti siano contenute nellimballaggio dellapparecchio. ACCESORIOS INCLUIDOS Desembale el aparato y verificar que los siguientes accesorios estn en la caja. BIJGELEVERDE ACCESSOIRES Controleer na het uitpakken of de volgende onderdelen voorhanden zijn.

This product complies with the radio frequency interference requirements of the Council Directive 82/499/EEC and/or 87/308/EEC.

Cet appareil est conforme aux prescriptions de la directive communautaire 87/308/CEE.

Diese Gerte entsprechen der EG-Richtlinie 82/499/EWG und/oder 87/308/EWG.

Dette apparat overholder det gaeldende EF-direktiv vedrrende radiostj.

Questo apparecchio conforme al D.M.13 aprile 1989 (Direttiva CEE/87/308) sulla soppressione dei radiodisturbi.

Este producto est de acuerdo con los requisitos sobre interferencias de radio frequencia fijados por el Consejo Directivo 87/308 CEE.

Dit product voldoet aan de EEG normen betreffende radio-frekwentie storingen 82/499/EEG en/of 87/308/EEG.

3

1 CDC-S75

CD CHANGER CDCS75 1 2 3

TIME EDIT REPEAT RANDOM SKIP

SEARCH

PLAY CHANGE OPEN/CLOSE

TIME

SINGLE SINGLE REMAIN TOTAL TOTAL REMAIN

TOTAL REMAIN

S F REPEAT PROGRAM RANDOM

EDIT A B

2 3 4 5 6 7 8 9 10

11 12 13 14 15 16 17 18 19

1

20 OVER

1 2

5

67 8

3

9

4

0

A

1

92

3

4 5 6 7 8

0 A

4

2 RX-S75

DSS ON/OFF

MODE

VOLUMEINPUT SELECTOR CD/TAPE/TUNER/AUX 1/AUX 2 POWER

STEREO RECEIVER RXS75

PHONES DISPLAY DOWN UP

TUNER PRESET

A/B/C/D/E

TIMER

MEMORY

TIME ADJ

DOWN

HOUR

UP

MINUTE

TUNING

AUTO/MAN'L

SEC

BAND AUTO MEMO

TIMER REC

BASS

+

TREBLE

+

BALANCE

L R

0 I0

SP/PHONES

Active Servo

Technology

ROCK JAZZ

CLASSIC RELAXED

MHz

MEMORY AUTO TUNING STEREO TUNED SLEEP TIMER

DSS

B C D FGE H

I J K L M N O P Q R S T U

I J K L

M

B C D

F G

E

H K

5

RDS MODE FREQ/PS/PTY/RT/CT

PTY SEEK

MODE

START

VOLUMEINPUT SELECTOR CD/TAPE/TUNER/AUX/PHONO POWER

PTY SELECTOR

STEREO RECEIVER RXS75

PHONES DISPLAY DOWN UP

TUNER PRESET

A/B/C/D/E

TIMER

MEMORY

TIME ADJ

DOWN

HOUR

UP

MINUTE

TUNING

AUTO/MAN'L

SEC

BAND AUTO MEMO

TIMER REC

BASS

+

TREBLE

+

BALANCE

L R

0 I0

Active Servo

Technology

MHz

MEMORY PTY H AUTO TUNING STEREO TUNED SLEEP TIMER

V C D WX Y H

I J K L M N O P Q R S T U

B C D

F N G H J

E

I

6

3 KXW-S75

4 NX-S75

CASSETTE DECK KXWS75

EJECT EJECTMODE DUBBING REC/PAUSE

NORM HIGH OFF B C

PLAYBACK RECORD/PLAYBACK

DECK A DECK B

DIRECTION

PLAY

NR

`

Z [ \ ]

a

b c e h kd ij

l a

f g

m

n

7

1 2 3 4 5

CD

6 7 8 6 7 8 9 0

1 2 3 4 5

TIME PROG TAPE EDIT +10

A B C D E

REPEAT RANDOM STOP PLAY/PAUSE OPEN/CLOSE

MODE DISC SKIP TUNER

DECK A/B

PLAY STOP PLAY TAPE

INPUTREC/PAUSE

- +

- +

EFFECT LEVEL SP/PHONES MODE DSS

POWER SLEEP DISPLAY VOLUME

1

2

3

4

5

6

8 9

0

A B

C

7

5

2

3

1 6

0.2 m 6 m (8 20)

30 30

7

1 2 3 4 5

CD

6 7 8 6 7 8 9 0

1 2 3 4 5

TIME PROG TAPE EDIT +10

A B C D E

REPEAT RANDOM STOP PLAY/PAUSE OPEN/CLOSE

MODE DISC SKIP TUNER

D

E F

HIJKL

M

N O

P

G

DECK A/B

PLAY STOP PLAY TAPE

INPUTREC/PAUSE

- +

- +

EFFECT LEVEL SP/PHONES MODE DSS

POWER SLEEP DISPLAY VOLUME

QR S T

U V

W

8

8

B

PHONES

9

To AC outlet Vers la prise c.a. Zur Netzsteckdose Till ntuttag Alla presa AC Al tomacorriente Naar wisselstroom-stopcontact

0

A

DECK A/B INPUTREC/PAUSE

- +

- +

EFFECT LEVEL SP/PHONES MODE DSS

POWER SLEEP DISPLAY VOLUME

E-1

E n

g lish

ENGLISH

INTRODUCTION

CONTENTS

Page

PRECAUTIONS..................................................................2-3

SETTING UP THE SYSTEM .................................................3

NAMES OF CONTROLS AND INDICATORS ....................4-5

REMOTE CONTROL TRANSMITTER................................5-6

REMOVING THE FRONT GRILLE ........................................6

LISTENING WITH HEADPHONES........................................6

OPEN/CLOSE THE CONTROL DOOR .................................6

CONNECTIONS..................................................................7-8

TURNING THE POWER ON/OFF TO THIS SYSTEM...........8

SETTING THE CLOCK ..........................................................9

SOUND CONTROL..............................................................10

DIGITAL SUPER SURROUND (DSS) PROCESSOR CONTROL .........10-11

Page

COMPACT DISC PLAYER OPERATION.......................11-18

TUNING OPERATION ....................................................19-21

RECEIVING RDS STATIONS ...............................22-25

TAPE DECK OPERATION ............................................26-29

RECORDING COMPACT DISCS ...................................30-35

OTHER RECORDINGS...................................................36-37

HOW TO USE THE BUILT-IN TIMER.............................38-41

USING EXTERNAL UNITS ..................................................42

MAINTENANCE ...................................................................43

TROUBLESHOOTING .........................................................44

SPECIFICATIONS................................................................45

Thank you for purchasing this YAMAHA product. We hope it will give you many years of trouble-free enjoyment. For the best performance, read this manual carefully. It will guide you in operating your YAMAHA product.

FEATURES

75W + 75W (6) Output Power, 10% THD, 1 kHz

Random Access Programmable CD Playback

Single Track/Entire Disc/All Disc Repeat Play

Random-sequence Play

Automatic Synchronized Recording with CD Playback

Automatic CD Editing Function for Recording to Tape

Double Cassette Tape Deck with Automatic Reversing Function

2-Way Speed Dubbing

Dolby B/C Noise Reduction System

40 Station Automatic Preset Tuning

Multi-Use Timer/Sleep Timer

Active Servo Processing Speaker System (NX-S75)

Remote Control Capability

4-Mode Digital Super Surround (DSS) Processor

Digital Super Surround Effective Even by Listening with Headphones

Multi-Functions for RDS Broadcast Reception

For basic source play, the following illustrations on top of pages will help you to look for the section you need.

......CD playback ......Tuning

......Tape playback/recording

E-2

NOTE Please check the copyright laws in your country to record from records, compact discs, radio, etc. Recording of copyright material may infringe copyright laws.

IMPORTANT Please record the serial number of this unit in the space below.

Serial No.:

The serial number is located on the rear of the unit. Retain this Owners Manual in a safe place for future reference.

WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION (FOR CANADA MODEL) TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT AND FULLY INSERT.

FOR CANADIAN CUSTOMER THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE- CAUSING EQUIPMENT REGULATIONS.

PRECAUTIONS: READ THIS BEFORE OPERATING YOUR UNIT

CD pickup Leave the power on with no disc in the unit until normal playback is possible (about 1 hour).

Tape head Leave the power on with no cassette in the unit until normal playback is possible (about 1 hour). Note If condensation forms on the tape head, foreign matter may accumulate during use.

Remote control Wipe off condensation on the transmitter window with a soft cloth before operating the unit.

To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference.

This system is equipped with the newly developed Active Servo Processing Speaker System. It is not designed for use with conventional speakers. Therefore, do not attempt to connect other speakers than the provided speaker system.

Choose the installation location of this unit carefully. Avoid placing it in direct sunlight or close to a source of heat. Also avoid locations subject to vibration and excessive dust, heat, cold or moisture. Keep it away from sources of hum such as transformers and electric motors.

Do not operate this unit upside-down. It may overheat, possibly causing damage.

Never open the cabinet. If something drops into the set, contact your dealer.

The openings on the cabinet assure proper ventilation of the unit. If these openings are obstructed, the temperature inside the cabinet will rise rapidly and eventually damage the circuits. Therefore, avoid placing objects against these openings and do not install the unit where the flow of air through the ventilation openings could be impeded.

Always set the VOLUME control to minimum before starting the audio source: increase the volume gradually to an appropriate level after play has started.

When not planning to use this unit for long periods of time (ie., vacation, etc.), disconnect the AC power plug from the wall outlet.

Grounding or polarization Precautions should be taken so that the grounding or polarization of an appliance is not defeated.

Do not use force on switches, controls or connection wires. When moving the unit, first disconnect the power plug and the wires connected to other equipment. Never pull the wire itself.

Do not attempt to clean the unit with chemical solvents; this might damage the finish. Use a clean, dry cloth.

Be sure to read the TROUBLESHOOTING section regarding common operating errors before concluding that the unit is faulty.

To prevent lightning damage, disconnect the AC power plug and the antenna cable when there is an electrical storm.

Do not plug the AC power plug to the wall socket before you finish all connections.

Never allow metallic items (e.g. screwdrivers, tools, etc.) to come near the cassette decks record/playback head assembly in this unit. Doing so may not only scratch or damage the heads mirror- smooth finish, it may change the magnetic characteristics of the heads, causing a deterioration in reproduction performance quality.

Although the cassette decks record/playback heads used in this unit are high quality heads with outstanding reproduction characteristics, they can become dirty through the use of old tapes or from dust accumulation over time. This can have a serious effect on reproduction quality. Clean the heads regularly with one of the commonly available head cleaners or with cleaning solutions.

The voltage to be used must be the same as that specified on this unit. Using this product with a higher voltage than that which is specified is dangerous and may result in a fire or other type of accident causing damage. YAMAHA will not be held responsible for any damage resulting from use of this unit with a voltage other than that which is specified.

The sound level at a given volume setting depends on speaker location and other factors. Care should be taken to avoid exposure to sudden high levels of sound, which may occur when turning on the unit with the volume control setting at high, and to continuous high levels of sound.

Sudden temperature changes and storage or operation in an extremely humid environment may cause condensation inside the cabinet. Condensation can cause the unit to malfunction. To eliminate condensation:

For U.K. customers If the socket outlets in the home are not suitable for the plug supplied with this appliance, it should be cut off and an appropriate 3 pin plug fitted. For details, refer to the instructions described below. Note: The plug severed from the mains lead must be destroyed, as a plug with bared flexible cord is hazardous if engaged in a live socket outlet.

SPECIAL INSTRUCTIONS FOR U.K. MODEL

IMPORTANT: The wire in the mains lead are coloured in accordance with the following code:

Blue: NEUTRAL Brown: LIVE

The colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug. Proceed as follows: the wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. Making sure that neither core is connected to the earth terminal of the three pin plug.

E-3

E n

g lishCAUTION FOR CARRYING THIS UNIT

Be sure not to carry or tip this unit with discs remaining in it.

CAUTION FOR MOVING THIS UNIT Before moving this unit, first remove all discs from the disc table and close the table by pressing the OPEN/CLOSE button, and then switch off the power by pressing the POWER switch, and last, after you confirm that no disc is illuminated on the display, disconnect the power plug from the AC outlet.

SETTING UP THE SYSTEM

CAUTION 1 Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

CAUTION 2 As the laser beam used in this unit is harmful to the eyes, do not attempt to disassemble the cabinet. Refer servicing to qualified personnel only.

Laser component in this product is capable of emitting radiation exceeding the limit for Class 1.

PRECAUTIONS: READ THIS BEFORE OPERATING YOUR UNIT

WARNING

To reduce the risk of fire or electric shock, do not expose this unit to rain or moisture.

To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

This unit is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located on the rear exterior. (Europe and U.K. model only)

Laser Diode Properties Material: GaAlAs Wavelength: 780nm Emission Duration: continuous Laser Output: max. 44.6W* * This output is the value measured at a distance of about 200mm

from the objective lens surface on the Optical Pick-up Block.

The apparatus is not disconnected from the AC power source as long as it is connected to the wall outlet, even if the apparatus itself is turned off.

1 cm 1 cm 10 cm10 cm

10 cm

10 cm 10 cm

10 cm

Setup examples Place this system as illustrated on the left and allow spaces more than indicated around the system and more than 10 cm (3-15/16) behind the system to assure good ventilation. Be sure not to place another unit or any object on top of the receiver (RX-S75) to prevent the ventilation holes on the top panel of the receiver from being obstructed. Otherwise, it may cause fire or damage to the receiver.

Notes When placing the speakers apart from the main units,

allow a space of at least 10 cm (3-15/16) from above, behind and on the both sides of the main units.

If the system is put in a rack, the front of it must be fully opened.

Disconnect the AC supply lead from the AC outlet before connecting or disconnecting any component.

VOLTAGE SELECTOR (General model only) The voltage selector on the rear panel of this unit must be set for your local main voltage BEFORE plugging into the AC main supply. Voltages are 110/120/220/240V AC, 50/60 Hz.

RX-S75 CDC-S75KXW-S75

RX-S75

CDC-S75

KXW-S75

E-4

NAMES OF CONTROLS AND INDICATORS

CD player (CDC-S75)

1 Disc Table

2 Stop Button:

3 Disc Selector Buttons

4 TIME Button

5 EDIT Button

6 REPEAT Button

7 RANDOM Button

8 SKIP Buttons: / (SEARCH Buttons: / )

9 Play/Pause Button: /

0 OPEN/CLOSE Button:

A PLAYXCHANGE Button

Receiver (RX-S75)

B INPUT SELECTOR Control

C POWER Switch

D Remote Control Sensor

E SP/PHONES Mode Selector Button

F DSS ON/OFF Selector Button

G DSS MODE Selector Button

H VOLUME Control

I PHONES Jack

J DISPLAY Button

K TUNER PRESET DOWN/UP Buttons

L A/B/C/D/E (TIMER) Button

M MEMORY (TIME ADJUST) Button

N TUNING DOWN (HOUR) Button

O TUNING UP (MINUTE) Button

P AUTO/MANL (SEC) Button

Q BAND Selector Button

R AUTO MEMORY (TIMER REC) Button

S BASS Tone Control

T TREBLE Tone Control

U BALANCE Control

V INPUT SELECTOR (PTY SELECTOR) Control

W PTY SEEK MODE Button

X RDS MODE Selector Button

Y PTY SEEK START Button

Display

For CD player 1 Track Number Indicator

2 (S, F) REPEAT Indicator

3 Time Display

4 Play Indicator:

5 Disc Indicator

6 EDIT Indicator

7 Tape Side Indicator

8 Music Calendar Indicator

9 Music Calendar OVER Indicator

0 RANDOM Play Indicator

A PROGRAM Indicator

For receiver B Preset Number Indicator

C Band Indicator

D Station Frequency Display

E TUNED Indicator

F MEMORY Indicator

G AUTO TUNING Indicator

H STEREO Indicator

I SLEEP Indicator

J TIMER Set Indicator

K Effect Level Indicator

L DSS Mode Indicators

M Phones Mode Indicator

N PTY H Indicator

(See figure 1 and 2 on page 3 5 at the beginning part of this manual.)

E-5

E n

g lish

Tape deck (KXW-S75)

Z DECK A Cassette Compartment

[ DECK A Selector Button and Indicator

\ DECK B Selector Button and Indicator

] DECK B Cassette Compartment

` Stop Button:

a Play Direction Indicators

b DECK A EJECT Button

c Fast Wind Button:

d Play Button:

e Reverse MODE Switch

f DUBBING (NORMAL/HIGH) Buttons and Indicators

g REC/PAUSE Button and Indicator

h DOLBY NR Switch

i Play Button:

j Fast Wind Button:

k DECK B EJECT Button

l PLAY Indicator

Speakers (NX-S75)

m YST Port

n Speaker Terminals

NAMES OF CONTROLS AND INDICATORS

(See figure 3 and 4 on page 6 at the beginning part of this manual.)

Names of control buttons

(See figure 5 on page 7 at the beginning part of this manual.)

Receiver control buttons

1 Remote Control Transmitter Window

2 Preset Station Number Buttons

3 A, B, C, D, E Selector Buttons

4 EFFECT LEVEL (Down)/+ (Up) Buttons

5 POWER Switch

6 SLEEP Button

7 SP/PHONES Mode Selector Button

8 DISPLAY Button

9 VOLUME (Down)/+ (Up) Buttons

0 TUNER Input Selector Button

A INPUT Selector Button

B DSS On/Off Button

C DSS MODE Selector Button

CD player control buttons

D Track Number Input Buttons

E TIME Button

F REPEAT Button

G RANDOM Button

H Disc Play MODE Selector Button

I DISC SKIP Button

J STOP Button:

K Skip Buttons: / (Search Buttons: / )

L PLAY/PAUSE Button:

M PROGRAM Button

N TAPE Button

O EDIT Button

P OPEN/CLOSE Button:

Tape deck control buttons

Q Play Button:

R Stop Button:

S Play Button:

T Fast Wind Button:

U DECK A/B Button

V Fast Wind Button:

W REC/PAUSE Button:

REMOTE CONTROL TRANSMITTER

* Parts in shaded areas on the figure 5 are not equipped on U.K. and Europe models. This manual mainly uses illustrations for U.K. and Europe models.

E-6

(See figure 8 on page 8.)

The front grille is fastened to the enclosure at four points, and can be removed if desired. To remove the grille, hold on to both sides and slowly pull straight away from the speaker. To reattach, line up the four pegs on the speaker with the four corresponding holes on the inside surface of the grille and push gently.

Note When the grille is removed, take care not to touch the speaker units with your hands or to exert excessive force with tools.

REMOVING THE FRONT GRILLE

Loading the batteries for the remote control transmitter (See figure 6 on page 7.)

1 Remove the battery compartment cover. (Press the left edge of the cover to right with a finger, and then pull it upward.)

2 Insert 2 AA size batteries (UM/SUM-3, R6, HP-7 or equivalent) into the battery compartment. * Installing the batteries improperly may cause failure.

3 Replace the battery compartment cover.

Precautions for battery use Insert the batteries according to the direction indicated in

the battery compartment. Replace all batteries with new ones at the same time. Remove the batteries if they are weak or if the unit is not

in use for long periods. Dont mix normal batteries with rechargeable batteries.

Proper use of the remote control transmitter (See figure 7 on page 7.)

Aim (within the range of 60 with no obstacles) the remote control transmitter at the remote control sensor and operate as shown.

Notes concerning use Replace the batteries if control distance decreases or

operation becomes unstable. Periodically clean the transmitter window on the remote

control transmitter and the sensor on the main unit with a soft cloth.

Exposing the sensor on the main unit to strong light (especially an inverter type of fluorescent lamp etc.) may interfere with operation. In this case, reposition the main unit to avoid direct lighting.

Keep the remote control transmitter away from moisture, excessive heat, shock and vibrations.

The remote control transmitters usable range is within 0.2m (8) and 6m (20) away from the sensor.

REMOTE CONTROL TRANSMITTER

(See figure 9 on page 8.)

Be sure that your headphones have a 3.5 mm (1/8) diameter plug and are between 16 ohms and 50 ohms impedance. Recommended impedance is 32 ohms.

When headphones are connected, the speakers are defeated automatically. Adjust the VOLUME control for desired volume.

LISTENING WITH HEADPHONES

OPEN/CLOSE THE CONTROL DOOR

When it is not necessary to operate controls inside the control door, close the door.

To open or close the door, press the right edge until it clicks.

E-7

E n

g lish

AM ANT

GND

FM ANT

75 UNBAL.

Antenna connection (1) Supplied FM antenna

Connect the FM antenna wire to the corresponding terminal and direct the FM antenna wire to the direction where the strongest signal can be received.

(2) Supplied AM (MW/LW) loop antenna

Connect the AM (MW/LW) loop antenna wires to the corresponding terminals. Position the AM (MW/LW) loop antenna for optimum reception. Place the AM (MW/LW) loop antenna on a shelf etc., or install it on the rack or wall with screws (not supplied).

Notes When static is still heard even after adjusting the position

of the AM (MW/LW) loop antenna, try reversing the wire connections (top to bottom).

Do not place the AM (MW/LW) loop antenna on the unit. It will result in noise generation, since the unit is equipped with digital electronics. Place the AM (MW/LW) loop antenna away from the unit.

(3) External FM antenna

Use an external FM antenna instead of an indoor FM antenna if you need better reception. Consult your dealer.

(4) External AM (MW/LW) antenna

Use an external AM (MW/LW) antenna if you need better reception. Consult your dealer.

Note When using an external AM (MW/LW) antenna, be sure to keep the wire of the AM (MW/LW) loop antenna connected.

CONNECTIONS

AM ANT

GND

FM ANT

75 UNBAL.

or

Earth rod

7.5 m (25 feet)

15 m (49 feet)

* For U.K. and Europe models, AM is replaced by MW LW.

(1)

(2)

(3)

(4)

FREQUENCY STEP switch (General model only) Because the interstation frequency spacing differs in different areas, set the FREQUENCY STEP switch (located at the rear) according to the frequency spacing in your area. Before setting this switch, disconnect the AC supply lead of this unit from the AC outlet.

Never plug the AC supply lead of this system into the AC outlet until all connections are completed.

100 kHz 10 kHz

FM AM

50 kHz 9 kHz

FREQUENCY STEP

E-8

(Black wire with white line plus (+) terminal, black wire minus () terminal)

STANDBY mode While the power is on, pressing the POWER switch (or the POWER switch on the remote control transmitter) switches the system to the STANDBY mode. (In this mode, the display shows only the time.) In this mode, main voltage is still present inside the system. If you want to switch off the system completely, disconnect the AC power plug from the AC outlet.

TURNING THE POWER ON/OFF TO THIS SYSTEM

(See figure B on page 8.)

If the AC supply lead is connected to the AC outlet, this system can be turned ON and OFF (STANDBY mode) by pressing the POWER switch on the front panel of RX-S75 or the POWER switch on the remote control transmitter.

Automatic power-on function Even when the power is off, pressing the following buttons will turn the system on, and then perform their own functions.

For Tuner operation TUNER on the remote control transmitter

For CD player operation / , disc selector buttons, OPEN/CLOSE on the front

panel of CDC-S75 / , OPEN/CLOSE on the remote control transmitter

For tape deck operation , , DECK A, DECK B on the front panel of KXW-S75 , , DECK A/B on the remote control transmitter

Automatic power-off function When the CD or TAPE input source is selected, if there is no operation and in the stop mode for about 30 minutes, the system will be turned off automatically.

Speaker connection Connect each speaker wire to the SPEAKERS terminals.

Cautions Do not let the bare speaker wires touch each other as this

could damage the receiver and/or speakers. When connecting the speakers to the unit, be sure to

connect the speaker wires properly. Do not make a mistake from the right channel to the left channel and from the plus (+) terminal to the minus () terminal.

Do not connect these SPEAKERS terminals to speakers other than the provided speaker system NX-S75.

System connection (See figure 0 on page 8.)

Connect the red connector on the rear of CDC-S75 to the red socket on the rear of RX-S75.

Connect the black connector on the rear of KXW-S75 to the black socket.

How to disconnect the system connector Grasp both sides of the connector to disconnect the connector.

Connecting the AC supply lead (See figure A on page 8.)

After connecting the speakers and system connectors, plug the AC supply lead into a convenient AC outlet.

Unplug the AC supply lead from the AC outlet if the unit is not to be used for a long period of time.

CONNECTIONS

R L

Right Left

E-9

E n

g lish1 While the power is on, press the DISPLAY button to

display the time. If the power is off, you can proceed to the next step.

2 While pressing the TIME ADJ button, press the HOUR button and set the hour. * Press the HOUR button once to advance the time by 1

hour. Press and hold to advance continuously.

3 While pressing the TIME ADJ button, press the MINUTE button and set the minute. * Press the MINUTE button once to advance the time by

1 minute. Press and hold to advance continuously. * The hour setting will not advance even if minute is

advanced from 59 to 00.

To display the time by second While pressing the SEC button, the current time is displayed by minute and second.

To reset the second to 00 While pressing the SEC button, press the TIME ADJ button. * If the current second is lower than 30, it is reset to 00. * If the current second is higher than 30, the minute is

advanced by 1 minute and the second is reset to 00. (If the current minute is 59, in this case, the hour is also advanced by 1 hour.)

In the event of a power failure or when the AC supply lead is disconnected. The time display will go out, however, the clock will function for about 5 minutes without power supply. So you do not have to reset the time if the AC power supply is resumed within about 5 minutes. When the AC power supply is resumed after more than 5 minutes pass without power supply, the time display will flash on and off to indicate that the time must be reset.

Note If this system is left for several minutes without setting the time after the AC power lead of this system is connected to the AC outlet, there may be a case that the display is turned into a demonstration mode. (This mode is virtually unnecessary for using this system.) In this case, first turn the power on by pressing the POWER switch to cancel the mode, and then set the time.

DISPLAY

MEMORY

TIME ADJ

DOWN

HOUR

UP

MINUTE

TUNING

MEMORY

TIME ADJ

DOWN

HOUR

UP

MINUTE

TUNING

SETTING THE CLOCK

Changes.

Changes.

SecondMinute

1

3

2

AUTO/MAN'L

SEC

E-10

VOLUME

0 I0

- + VOLUME

SOUND CONTROL

Volume Front panel operation Rotate the VOLUME control towards 10 to increase the volume, and towards 0 to decrease the volume.

Remote control operation Press the VOLUME + button to increase the volume and the VOLUME button to decrease the volume.

Balance Adjust the balance of the output volume to the left and right speakers to compensate for sound imbalance caused from the speaker settings or the listening room condition. Turn this clockwise to emphasize the right and counterclockwise for the left.

Tone BASS : Turn this clockwise to increase (or counter-

clockwise to decrease) the low frequency response.

TREBLE : Turn this clockwise to increase (or counter- clockwise to decrease) the high frequency response.

BALANCE

L R

BASS

+

TREBLE

+

The Digital Super Surround (DSS) Processor built into this unit presents you with sound effect which simulates acoustic environments suitable for some genres of music.

This unit provides the following 4 DSS modes.

Mode

ROCK

JAZZ

CLASSIC

RELAXED

Feature

Low frequency and high frequency of the source sound are somewhat emphasized. It is suitable for listening to rock or pop music.

This mode creates a sound field with much presence adding spatial effect as if music instruments are coming in front.

The sound stage is expanded. It is suitable for listening to classic music, etc.

This mode is suitable for easy-listening music. The sound is reproduced with a soft, comfortable atmosphere.

MODE

ROCK

JAZZ

CLASSIC

RELAXED

DIGITAL SUPER SURROUND (DSS) PROCESSOR CONTROL and Europe models>

E-11

E n

g lish

COMPACT DISC PLAYER OPERATION

Care of compact discs Compact discs are fairly resistant to damage, however mistracking can occur due to an accumulation of dirt on the disc surface. Follow the guidelines below for maximum enjoyment from your CD collection and player. Do not write on either side of the disc, particularly the non-

label side. Signals are read from the non-label side. Do not mark this surface.

Keep your discs away from direct sunlight, heat and excessive moisture.

Always hold the CDs by the edges. Fingerprints, dirt or water on the CDs can cause noise or mistracking. If a CD is dirty or does not play properly, clean it with a soft, dry cloth, wiping straight out from the center, along the radius.

Listening to the music with the DSS 1 Press the DSS ON/OFF selector button so that the effect

level indicator lights up on the display.

2 Select a desired DSS mode by pressing the DSS MODE selector button once or more until the name of the desired mode appears on the display.

3 Playback a source. (For source playback, refer to other sections described later.)

4 Adjust the level of effects by pressing the EFFECT LEVEL down () or up (+) button. * Effect level can be checked with the effect level indicator

on the display. * Each of the DSS modes can be set with a different effect

level.

If you will not use the DSS Press the DSS ON/OFF selector button so that the effect level indicator on the display goes off.

When listening with headphones Press the SP/PHONES mode selector button so that the phones mode indicator lights up on the display. You can obtain a DSS effect suitable for the headphone listening. If not using headphones, the SP/PHONES mode selector button should be pressed so that the phones mode indicator on the display goes off.

Note DSS effect is also recorded along with a source. If you wish to record a source without DSS effect, turn the DSS off when recording.

ROCK

DSS

1 2 3 4 5

CD

6 7 8 6 7 8 9 0

1 2 3 4 5

TIME PROG TAPE EDIT +10

A B C D E

REPEAT RANDOM STOP PLAY/PAUSE OPEN/CLOSE

MODE DISC SKIP TUNER

DECK A/B

PLAY STOP PLAY TAPE

INPUTREC/PAUSE

- +

- +

EFFECT LEVEL SP/PHONES MODE DSS

POWER SLEEP DISPLAY VOLUME

DIGITAL SUPER SURROUND (DSS) PROCESSOR CONTROL and Europe models>

Phones mode indicator

1 2

SP/PHONES

1

2

4

SP/PHONES

Effect level indicator

E-12

CD playback 1 Select the CD position with the INPUT SELECTOR

control, watching the display.

2 Press the OPEN/CLOSE button to open the disc table.

3 Place discs on the trays, label side up. * Up to three discs can be loaded on the trays. * 8 cm (3) discs may be played without an adaptor.

4 Press the OPEN/CLOSE button to close the disc table. * The total number of tracks and the total playing time of

the disc being selected will be displayed for several seconds.

* The music calendar will be displayed only for the number of tracks on the disc being selected.

* If the compact disc contains more than 20 tracks, the OVER indicator will light up on the music calendar.

5 If necessary, change the disc play mode by pressing the disc play MODE selector button on the remote control transmitter while watching the display.

Single disc play mode: Only a designated disc is played back.

All disc play mode: All discs on the disc table are played back sequentially.

6 If necessary, select another disc by pressing the DISC SKIP button on the remote control transmitter once or more (so that the corresponding disc tray number is located on top of the disc indicator).

7 Press the play/pause / button to start playback from track 1. * The indicator will appear and playback will begin.

As the playback of each track on the music calendar is finished, that track number will go out.

For easier operation Pressing the disc selector button (1, 2 or 3) will select the disc directly, and playback will begin from track 1 automatically.

COMPACT DISC PLAYER OPERATION

Total number of tracks

The disc on the tray located on top of this indicator is now being selected.

Music calendar Total playing time

1 2 3 4 5

CD

6 7 8 6 7 8 9 0

1 2 3 4 5

TIME PROG TAPE EDIT +10

A B C D E

REPEAT RANDOM STOP PLAY/PAUSE OPEN/CLOSE

MODE DISC SKIP TUNER

DECK A/B

PLAY STOP PLAY TAPE

INPUTREC/PAUSE

- +

- +

EFFECT LEVEL SP/PHONES MODE DSS

POWER SLEEP DISPLAY VOLUME

TOTAL

2 3 4 5 6 7 8 9 10

11 12

1

Lights up only when the all disc play mode is selected.

POWER Receiver

1

CD Player

Disc selector buttons

7, 1, 2

2, 4

3

6

5

2, 4

7, 1, 2

1

POWER

1 2 3 4 5

CD

6 7 8 6 7 8 9 0

1 2 3 4 5

TIME PROG TAPE EDIT +10

A B C D E

REPEAT RANDOM STOP PLAY/PAUSE OPEN/CLOSE

MODE DISC SKIP TUNER

DECK A/B

PLAY STOP PLAY TAPE

INPUTREC/PAUSE

- +

- +

EFFECT LEVEL SP/PHONES MODE DSS

POWER SLEEP DISPLAY VOLUME

1 2 3 4 5

CD

6 7 8 6 7 8 9 0

1 2 3 4 5

+10

E

COMPACT DISC PLAYER OPERATION

Direct operation Even when an input source other than CD player is selected, pressing the play/pause / button, a disc selector button or the RANDOM play button, or pressing the front edge of the disc table gently will start playback directly. In this case, if the tape deck is playing back a tape, it will be stopped automatically. * These ways of playback can also be used to close the disc

table. If the table is closed in these ways, playback will begin automatically, however, the display will not show the total number of tracks and the total playing time of the disc to be played.

PLAYXCHANGE During playback, you can open the disc table by pressing the PLAYXCHANGE button without interrupting disc playback. However, in this case, pressing the DISC SKIP button or a disc selector button has no effect.

Precautions If TV or radio interference occurs during CD player

operation, move the unit away from the TV or radio. Subjecting the unit to shock or vibration can cause

mistracking. Playing some compact discs at high volume can cause

mistracking. In this case, listen at lower volume. Do not pull open the disc table forcibly with your hands. Do not push the disc table while it is moving. If the power fails while the table is open, wait until the

power supply returns or gently push the table manually to close it.

The temperature range for playing compact discs is recommended to be 5C (41F) 35C (95F).

Direct-selection play By using the track number input buttons on the remote control transmitter, any track you wish to listen to can be played directly.

Use the track number input buttons to select the desired track number. Play will begin automatically.

A. For example, to choose selection 5 Press the 5 button.

B. For example, to choose selection 12 (1)Press the +10 button. (2)Within 3 seconds, press 2 button.

C. For example, to choose selection 20 (1)Press the +10 button. (2)Within 3 seconds, press the +10 button again. (3)Within 3 seconds, press the 0 button.

Note If you select a track number higher than the number of tracks on the disc, play will begin from the last track on the disc .

E-13

E n

g lish

To interrupt playback

1 Press the play/pause / button. * The indicator will flash.

2 Press the play/pause / button to resume playback from the same point.

To stop playback Press the stop button.

To switch the unit off after use Turn the unit off by pressing the POWER switch. (The indicators will go off except for the current time display.)

E-14

COMPACT DISC PLAYER OPERATION

Skip search and Manual search are performed using the same buttons.

Skip search The beginning of any track can be found automatically.

1 Select a disc and begin playback.

2 Press the button to advance or button to reverse through the disc. Press once for each track to be advanced or reversed. Press once to advance to the track following the

one now playing back. Press once to return to the start of the track now

playing back. Press twice to return to the track before the track

now playing back.

Notes This function can also be performed while the unit is

stopped. Press the play/pause / button when your desired track number appears in the track number display. Playback will begin from the beginning of the track.

This function will be performed forward or backward from any point on the disc. However, it will not move forward during playback of the final track.

Manual search 1 Begin playback.

2 Press and hold the button to advance play rapidly, and the button to reverse play rapidly. * The sound can be heard (although slightly garbled)

during manual search in either direction. This is convenient for reviewing the contents quickly.

Note Manual search can also be performed while playback is paused, though no sound will be heard.

1 2 3 4 5

CD

6 7 8 6 7 8 9 0

1 2 3 4 5

TIME PROG TAPE EDIT +10

A B C D E

REPEAT RANDOM STOP PLAY/PAUSE OPEN/CLOSE

MODE DISC SKIP TUNER

DECK A/B

PLAY STOP PLAY TAPE

INPUTREC/PAUSE

- +

- +

EFFECT LEVEL SP/PHONES MODE DSS

POWER SLEEP DISPLAY VOLUME

1

2

1

2

CD player

COMPACT DISC PLAYER OPERATION

Program play You can program up to 20 tracks in any desired order.

1 Load discs and close the disc table.

2 When in the stop mode, press the PROG button to prepare for programming. * PROGRAM and P-01 will light up on the display,

and all track numbers on the selected disc begin flashing.

3 If necessary, select a desired disc by pressing the DISC SKIP button.

4 Use the track number input buttons to select the desired track number. * The selected track number and the total play time of

the programmed tracks will light up on the display, and soon it is replaced by the display of the next playback order. Programmed track numbers on the selected disc will stop flashing and light up on the music calendar.

* Pressing the TIME button displays the total play time of the programmed tracks for about 1 second, and then it is replaced by the display of the next playback order.

* For example, to choose selection 12 (1)Press the +10 button. (2)Press the 2 button.

5 Repeat steps 3 and 4 for any other track. Up to 20 tracks can be programmed.

6 Press the play/pause / button to start playback of programmed tracks.

Notes It is also possible to program a sequence of tracks while

looking at the list of tracks on the surface of the disc before closing the disc table.

During playback or pause, programming is not possible. If the total time of the programmed tracks reaches 100

minutes or more, only the last two-digits will be displayed for the three-digit number.

The total time of the programmed tracks will not be displayed, if a track number higher than 19 is programmed.

Skip search can be performed during playing back, but only within the range of the programmed tracks.

Manual search can be performed during playing back to search through all tracks, including unprogrammed tracks.

If programs are made selecting tracks from more than one disc, pressing the PLAYXCHANGE button is useless during program play.

E-15

E n

g lish

1 2 3 4 5

CD

6 7 8 6 7 8 9 0

1 2 3 4 5

TIME PROG TAPE EDIT +10

A B C D E

REPEAT RANDOM STOP PLAY/PAUSE OPEN/CLOSE

MODE DISC SKIP TUNER

DECK A/B

PLAY STOP PLAY TAPE

INPUTREC/PAUSE

- +

- +

EFFECT LEVEL SP/PHONES MODE DSS

POWER SLEEP DISPLAY VOLUME

PROGRAM

2 3 4 5 6 7 8 9 10

11 12

1

TOTAL

PROGRAM

2 3 4 5 6 7 8 9 10

11 12

1

16

4

3

2 6

CD player

TIME

TIME

1

Display information during programming

Playback order

Selected disc

Selected track number Total playing time

Music calendar

E-16

To stop program play

Press the stop button. The first programmed track number will be displayed.

To resume playback, press the play/pause / button. Playback will begin from the beginning of the program.

To cancel a programmed sequence

There are several methods as described below. Press the stop button while the unit is stopped. Open the disc table. Switch off the power.

COMPACT DISC PLAYER OPERATION

To check program data

1. If during playing back, press the stop button. 2. Press the PROG button. 3. Each time the SKIP button is pressed, the track

numbers and sequential order of the programmed tracks can be checked one after another. The display of the track number can be returned (sequentially in reverse order) by pressing the SKIP button.

To correct program data

1. Follow the procedure described in To check program data.

2. Display the track number to be corrected by pressing the SKIP button.

3. Press a track number input button to select a track to replace the one displayed. The previously programmed track will be cleared from the memory and the new one will be programmed.

4. After the correction has been completed, press the PROG button or play/pause / button once again.

1 2 3 4 5

CD

6 7 8 6 7 8 9 0

1 2 3 4 5

TIME PROG TAPE EDIT +10

A B C D E

REPEAT RANDOM STOP PLAY/PAUSE OPEN/CLOSE

MODE DISC SKIP TUNER

DECK A/B

PLAY STOP PLAY TAPE

INPUTREC/PAUSE

- +

- +

EFFECT LEVEL SP/PHONES MODE DSS

POWER SLEEP DISPLAY VOLUME

/

PROG

CD player

Repeat play All discs, an entire disc, a single track or a programmed sequence can be continuously repeated.

1 While watching the display, press the REPEAT button once or more to select a desired repeat play mode (S REPEAT or F REPEAT).

2 Press the play/pause / button.

Repeat play modes

SINGLE REPEAT (S REPEAT) A single track is played back repeatedly. * This is also available in the program play mode and the

random play mode. (If the repeat play mode is switched off, the program play mode or the random play mode will be resumed.)

FULL REPEAT (F REPEAT)

When the unit is in the single disc play mode: A designated disc is played back repeatedly. * In the random play mode, the selected disc is repeatedly

played back, but the order of tracks is different every time.

When the unit is in the all disc play mode: All discs on the disc table are played back repeatedly. * In the random play mode, the random play is performed

among all discs and repeated with a different order of tracks every time.

Note In the program play mode, a sequence of programmed tracks is played back repeatedly.

To cancel the repeat play

Press the REPEAT button once or more so that the (S, F) REPEAT indicator goes out.

COMPACT DISC PLAYER OPERATION

E-17

E n

g lish

1 2 3 4 5

CD

6 7 8 6 7 8 9 0

1 2 3 4 5

TIME PROG TAPE EDIT +10

A B C D E

REPEAT RANDOM STOP PLAY/PAUSE OPEN/CLOSE

MODE DISC SKIP TUNER

DECK A/B

PLAY STOP PLAY TAPE

INPUTREC/PAUSE

- +

- +

EFFECT LEVEL SP/PHONES MODE DSS

POWER SLEEP DISPLAY VOLUME

OFF S REPEAT F REPEAT

2

1

1

2

CD player

E-18

Random play Tracks on a selected disc or all discs on the disc table can be played back in a random order.

1 Load discs and close the disc table.

2 If necessary, switch the disc play mode by pressing the disc play MODE selector button. * If the single disc play mode is selected, select a desired

disc by pressing the DISC SKIP button.

3 Press the RANDOM button to begin random play. * The RANDOM indicator will light up.

To cancel the random play Press the stop button, or press the RANDOM button again. The RANDOM indicator will go out.

Note This feature will not function during programming, or during program play.

Switching the time display Each time the TIME button is pressed, the display will change as described below.

[Example] When the second track is being played back (Refer to the illustration on the left.)

The elapsed play time for the track now playing back will be displayed. * 8 seconds have passed since the beginning of the

second track. The remaining play time for the current track will be

displayed. * 2 minutes and 58 seconds remain till the end of the

second track. The total play time of the disc will be displayed.

(If the unit is in the program play mode, the total play time of the programmed tracks will be displayed.)

The total remaining play time from the point being played at that time will be displayed. * 41 minutes remain till the end of the disc.

Notes During random play, the total remaining play time on the

disc will not be displayed. The remaining play time will not be displayed for track

number 20 or higher. If track number 20 or higher is programmed, during the

program play, the total play time and the total remaining play time will not be displayed.

COMPACT DISC PLAYER OPERATION

1 2 3 4 5

CD

6 7 8 6 7 8 9 0

1 2 3 4 5

TIME PROG TAPE EDIT +10

A B C D E

REPEAT RANDOM STOP PLAY/PAUSE OPEN/CLOSE

MODE DISC SKIP TUNER

DECK A/B

PLAY STOP PLAY TAPE

INPUTREC/PAUSE

- +

- +

EFFECT LEVEL SP/PHONES MODE DSS

POWER SLEEP DISPLAY VOLUME

2 3 4 5 6 7 8 9 10

11 12

1

TOTAL REMAIN

2 3 4 5 6 7 8 9 10

11 12

1

REMAIN

2 3 4 5 6 7 8 9 10

11 12

1

TOTAL

2 3 4 5 6 7 8 9 10

11 12

1

1 2 3 4 5

CD

6 7 8 6 7 8 9 0

1 2 3 4 5

TIME PROG TAPE EDIT +10

A B C D E

REPEAT RANDOM STOP PLAY/PAUSE OPEN/CLOSE

MODE DISC SKIP TUNER

DECK A/B

PLAY STOP PLAY TAPE

INPUTREC/PAUSE

- +

- +

EFFECT LEVEL SP/PHONES MODE DSS

POWER SLEEP DISPLAY VOLUME

3 1

1

3

2

TIME

CD Player

TIME

CD player

Normally, if station signals are strong and there is no interference, quick automatic-search tuning (Automatic tuning) is possible. However, if signals of the station you want to select are weak, you must tune to it manually (Manual tuning).

Automatic tuning 1 Select the TUNER position with the INPUT SELECTOR

control, watching the display.

2 Select the reception band [FM or AM (MW or LW)] by pressing the BAND button while watching the display.

3 Press the AUTO/MANL button so that AUTO TUNING appears on the display. (In this mode, stations are received in stereo or monaural automatically.)

4 Press the TUNING UP button to tune to a higher frequency, or press the TUNING DOWN button to tune to a lower frequency. (When tuned to a station, TUNED will light up on the display.)

5 If the station where tuning search stopped is not the desired one, follow step 4 again.

* If the tuning search does not stop at the desired station, change to the Manual tuning method as described below.

* STEREO indicator will light up when an FM stereo broadcast with sufficient signal strength is received.

Manual tuning 1 Follow steps 1 and 2 of the Automatic tuning method.

2 Press the AUTO/MANL button so that AUTO TUNING disappears from the display. (In this mode, stations are received in monaural.)

3 Press and hold the TUNING UP button to tune to a higher frequency, or press and hold the TUNING DOWN button to tune to a lower frequency. Release it just before reaching the desired frequency, and then press it repeatedly until the desired frequency appears. (When tuned to a station, TUNED will light up on the display.)

Note If you tune to an FM station manually, it is received in monaural automatically to increase the signal quality.

AM is for U.S.A., Canada, Australia, Singapore and General models. MW/LW is for U.K. and Europe models.

TUNING OPERATION

E-19

E n

g lish

1 2 3 4 5

CD

6 7 8 6 7 8 9 0

1 2 3 4 5

TIME PROG TAPE EDIT +10

A B C D E

REPEAT RANDOM STOP PLAY/PAUSE OPEN/CLOSE

MODE DISC SKIP TUNER

DECK A/B

PLAY STOP PLAY TAPE

INPUTREC/PAUSE

- +

- +

EFFECT LEVEL SP/PHONES MODE DSS

POWER SLEEP DISPLAY VOLUME

Receiver

3, 2

4, 3

1

1

2

E-20

TUNING OPERATION

Preset tuning This unit can store station frequencies selected by tuning operation. With this function, you can select any desired station by only calling the corresponding preset station number. Up to 40 stations (8 stations x 5 areas) can be stored.

To store stations

(Example: To store a station to A1)

1 Tune to a desired station. (Refer to the previous page for tuning procedure.)

2 Press the MEMORY button. * MEMORY and P will flash on the display for about 5

seconds.

3 Select a desired area (A E) by pressing the A/B/C/D/E button while watching the display, before the MEMORY indicator goes out. (In this case, select area A)

4 Select a preset station number by pressing the TUNER PRESET DOWN or UP button repeatedly before the MEMORY indicator goes out. (In this case, select 1.)

5 Within about 5 seconds, press the MEMORY button again.

* In the same way, program other stations to A2, A3 ... A8. * You can program more stations to the preset station

numbers on other areas in the same way by selecting other areas in step 3.

To recall a preset station

1 Select the area of preset station numbers by pressing the A/B/C/D/E button.

2 Select the desired preset station number by pressing the TUNER PRESET DOWN or UP button repeatedly.

Notes A new setting can be programmed in place of the former

one. For presets the setting of the AUTO/MANL button is

stored along with the station frequency.

For easier operation By using the preset station number buttons and the A,B,C,D,E selector buttons on the remote control transmitter, a preset station number and an area can be selected directly.

Shows the displayed station has been programmed to A1.

1 2 3 4 5

CD

6 7 8 6 7 8 9 0

1 2 3 4 5

TIME PROG TAPE EDIT +10

A B C D E

REPEAT RANDOM STOP PLAY/PAUSE OPEN/CLOSE

MODE DISC SKIP TUNER

DECK A/B

PLAY STOP PLAY TAPE

INPUTREC/PAUSE

- +

- +

EFFECT LEVEL SP/PHONES MODE DSS

POWER SLEEP DISPLAY VOLUME

MHz

AUTO TUNING STEREO TUNED

Receiver

4, 2 2, 5

3, 1

4, 2

3, 1

Automatic preset tuning You can also make use of an automatic preset tuning function. By this function, this unit performs automatic tuning and stores stations with strong signals sequentially. Up to 40 stations are stored automatically in the same way as in the manual preset tuning method on the previous page.

1 Select the TUNER position with the INPUT SELECTOR control, watching the display.

2 Press and hold the AUTO MEMO button for about 2 seconds. * The MEMORY and AUTO TUNING indicators will flash.

This unit performs automatic tuning and received stations are programmed to A1, A2 ... A8 sequentially.

When the automatic preset tuning is completed The display shows the frequencies of the first preset station (stored to A1). Check the contents and the number of preset stations by following the procedure of the section To recall a preset station on the previous page.

To recall a preset station Simply follow the procedure of the section To recall a preset station on the previous page.

Notes The automatic preset tuning search will be performed

through all frequencies until 40 stations are stored. If the number of received stations is less than 40, the search will stop after searching all frequencies.

and Europe models only> The unit is originally set so that only RDS stations are programmed onto the area for FM stations by this operation. However, you can change the setting so that the unit can program not noly RDS stations but also other FM stations. (Refer to page 25 for details.)

With this function, only stations with sufficient signal strength are stored automatically. If the station you want to program is weak in signal strength, tune to it in monaural manually and program it by following the procedure of the section To store stations on the previous page.

You can replace a preset station by another FM or AM (MW or LW) station manually by simply following the procedure of the section To store stations on the previous page.

TUNING OPERATION

Fundamental rules of internal automatic preset tuning operation Basically, FM stations are programmed onto area A, B and C, and AM stations are programmed onto area D and E (MW stations are onto D and LW stations are onto E) in that order automatically. * If, for example, the number of received FM stations is not

enough to fill up three areas (A, B and C), AM (MW or LW) stations are programmed closely from the preceeding empty areas. In such a case, AM (MW) stations are programmed from area B or C (and LW stations are from area C or D.)

* Moreover, one area is programmed with stations of the same band only. If, for example, the last FM station is programmed to B4, B5B8 will be programmed with no station, and AM (MW) stations are programmed from area C.

E-21

E n

g lish

1 2 3 4 5

CD

6 7 8 6 7 8 9 0

1 2 3 4 5

TIME PROG TAPE EDIT +10

A B C D E

REPEAT RANDOM STOP PLAY/PAUSE OPEN/CLOSE

MODE DISC SKIP TUNER

DECK A/B

PLAY STOP PLAY TAPE

INPUTREC/PAUSE

- +

- +

EFFECT LEVEL SP/PHONES MODE DSS

POWER SLEEP DISPLAY VOLUME

Receiver

2

1

1

Memory back-up The memory back-up circuit prevents the programmed data from being lost even if the AC supply lead is disconnected from the AC outlet or the power is cut due to temporary power failure. If, however, the power is cut for more than one week, the memory may be erased. If so, it can be re-programmed by simply following the Preset tuning steps.

Displaying RDS data This unit can be turned into the following four modes to display RDS data.

PS (Program Service name) mode: Displays the name of the RDS station now being received instead of the frequency.

PTY (Program Type) mode: Displays the type of the program on the RDS station now being received. There are 15 program types to classify RDS stations as follows.

RT (Radio Text) mode: Displays information about the program (such as title of the song, name of the singer, etc.) on the RDS station now being received.

CT (Clock Time) mode: Displays current time. This signal comes from the RDS station now being received. Time of the built-in clock can be automatically corrected on the basis of this signal.

E-22

RDS (Radio Data System) is a data transmission system gradually being introduced by FM stations in many countries. Stations using this system transmit an inaudible stream of data in addition to the normal radio signal. RDS data contains various information, such as AF (Alternative Frequencies for the same program station),

PI (Program Identification), PS (Program Service name), PTY (Program Type), RT (Radio Text), CT (Clock Time), etc. RDS function is carried out among the network stations. * This unit utilizes PS, PTY, RT and CT to receive RDS

broadcast stations.

News: Short accounts of facts, events and publicly expressed views, reportage and actuality.

Current affairs: Topical program expanding or enlarging upon the news, generally in different presentation style or concept, including documentary debate, or analysis

Information: Program whose purpose is to impart advice in the widest sense, including meteorological reports and forecasts, consumer affairs, medical help, etc.

Sport: Program concerned with any aspect of sport.

Education: Program intended primarily to educate, of which the formal element is fundamental.

Drama: All radio plays and serials.

Culture: Programs concerned with any aspect of national or regional culture, including religious affairs, philosophy, social science, language, theatre, etc.

Science: Programs about the natural sciences and technology.

Varied: Used for mainly speech-based programs usually of light-entertainment nature, not covered by above categories. Examples are: quizzes, panel games, personality interviews, comedy and satire.

Pop: Commercial music, which would generally be considered to be of current popular appeal, often featuring in current or recent record sales charts.

Rock: Contemporary modern music, usually written and performed by young musicians.

M.O.R.: (Middle of the Road Music). Common term to describe music considered to be easy- listening, as opposed to Pop, Rock or Classical. Music in this category is often but not always, vocal, and usually of short duration (<5 min.)

Light classics: Classical Musical for general, rather than specialist appreciation. Examples of music in this category are instrumental music, and vocal or choral works.

Serious classics: Performances of major orchestral works, symphonies, chamber music etc., and including Grand Opera.

Other music: Musical styles not fitting into any of the above categories. Particularly used for specialist music, of which Jazz, Rhythm & Blues, Folk, Country, and Reggae are examples.

NEWS

AFFAIRS

INFO

SPORT

EDUCATE

DRAMA

CULTURE

SCIENCE

VARIED

POP M

ROCK M

M.O.R. M

LIGHT M

CLASSICS

OTHER M

BBC R3

RECEIVING RDS STATIONS

FREQ (usual) mode The frequency of the station being received is displayed.

PS (Program Service name) mode The name of the station being received is displayed. PS WAIT may flash while the unit is receiving the data. If the station does not employ the PS data service, NO PS lights up on the display for about 2 seconds and then returns to usual mode.

PTY (Program Type) mode The type of the program on the station being received is displayed. If the RDS station does not employ the PTY data service, NO PTY lights up on the display for about 2 seconds and then returns to usual mode. If the station has PS data, after that, it turns into the PS mode. In this mode, you can make this unit search for a station which is broadcasting a program of your desired program type. For details, refer to the next page.

RT (Radio Text) mode Information about the program on the station being received is displayed. Information is displayed by a maximum of 64 Roman Alphabets including umlaut sign. If other characters are used on the RT data, they are displayed with blank spaces. RT WAIT may flash while the unit is receiving the data. If the RDS station does not employ the RT data service, NO RT lights up on the display for about 2 seconds and then returns to usual mode. If the station has PS data, after that, it turns into the PS mode.

CT (Clock Time) mode Current time is displayed in the following form. The CT data from the station being received changes every minute.

This unit corrects time of the built-in clock by synchronizing it with the CT data. (This function can also be canceled, if so desired. Refer to page 25 for details.) CT WAIT may flash while the unit is receiving the data. If the data is accidentally cut off, CT WAIT may flash and then turn into NO CT. If the RDS station does not employ the CT data service, NO CT lights up on the display for about 2 seconds and then returns to usual mode. If the station has PS data, after that, it turns into the PS mode.

Note RDS data service cannot be utilized by this unit if the received signal is not strong enough. Especially, the RT (Radio Text mode) needs much data to be received, so it may occur that RT mode cannot be displayed even if other RDS modes (PS, PTY, etc.) are displayed.

1 FREQ mode

2 PS mode

3 PTY mode

5 CT mode

RDS MODE FREQ/PS/PTY/RT/CT

4 RT mode

E-23

E n

g lish

RDS MODE

To turn the unit into the RDS mode Press the RDS MODE selector button. If the station now being received is an RDS station, whenever pressed, the mode changes into the PS mode, PTY mode, RT mode, CT mode and returns to usual mode in turn. * If the station is not an RDS station, pressing the RDS

MODE selector button displays NO RDS on the display, and then it returns to the frequency display mode.

* When an RDS station is received, the display is automatically turned into the PS mode. Do not press the RDS MODE selector button until the display is turned into the PS mode. If the button is pressed before the display mode is changed, it may occur that NO PS appears on the display. This is because the unit has not received all of the RDS data on the station yet.

Hour Minute

Receiver

RECEIVING RDS STATIONS

E-24

Calling a preset RDS station by the program type (PTY SEEK) By designating a program type, the unit automatically searches all preset FM stations for an RDS station which broadcasts a program of that program type. * There are 15 program types to classify RDS stations. For

details, refer to page 22.

1 Turn the unit into the PTY SEEK mode by pressing the PTY SEEK MODE button. * The name of the program type of the station now being

received or NEWS flashes on the display.

2 Select the desired program type with the PTY SELECTOR. * If there is no operation for about 20 seconds, this mode

is canceled and turns into the frequency display. If the station has PS data, after that, it turns into the PS mode.

3 Press the PTY SEEK START button. The unit begins searching all preset FM stations. * PTY H (abbrev. of PTY HOLD) lights up on the

display. * The preset number indicator, the name of the program

type and AUTO TUNING flash. The preset number changes rapidly in sequence.

If a station which broadcasts a program of the program type is found, the unit stops at the station and turns into the frequency display. If the station has PS data, after that, it turns into the PS mode.

If the called station is not the desired one, press the PTY SEEK START button once more before PTY H goes out from the display. The unit begins searching for another station which broadcasts a program of the same program type.

If no station is found, NO PTY appears and then returns to frequency display. If the station has PS data, after that, it turns into the PS mode. * If the PTY SEEK START button is pressed once more

during searching, this mode is canceled and turns into the frequency display. If the station has PS data, after that, it turns into the PS mode.

To cancel this function If the PTY SEEK MODE button is pressed once more, the PTY SEEK mode is canceled and turns into the frequency display. If the station has PS data, after that, it turns into the PS mode.

Notes There may be a case that RDS data reception is not

possible due to poor reception conditions. If so, press the AUTO/MANL button so that AUTO TUNING goes off from the display. Though the reception mode is changed to monaural by this operation, when you change the display to an RDS mode, RDS data may be displayed.

If the signal strength gets weakened by external interference during receiving an RDS station, the RDS data service may be cut off suddenly and turn into the frequency display mode.

Receiver

2 1 3

RECEIVING RDS STATIONS

E-25

E n

g lish

RECEIVING RDS STATIONS Other functions which make use of RDS data service This unit has the following functions which make use of RDS data service. These are originally in operation [ON]. However, you can cancel these functions [OFF], if so desired.

ON (OFF) CT > CLOCK This unit corrects the time of the built-in clock automatically by synchronizing it with the CT data on the RDS station being received. * If you receive an RDS station of some other country,

the built-in clock is synchronized with the time setting of the country.

* If the built-in clock is not yet set for current time or reset due to a power failure etc., it will be set for the time of the CT data automatically, whether this setting is ON or OFF.

ON (OFF) LOCAL > CT If the RDS station being received employs the local time (summer time etc.) data service, its time is displayed in the CT mode. * If the setting of function is ON, the built-in clock is

synchronized with the local time data.

ON (OFF) A. M. > RDS Only RDS stations are programmed onto the area for FM stations by the automatic preset tuning operation when the setting is ON. (See page 21 for the operating procedure.) If you switch this function OFF, not only RDS stations but also other FM stations are programmed along with MW and LW stations by the automatic preset tuning operation.

To switch these functions on and off

1 Select the FM band by pressing the BAND button, watching the display.

2 Press the DISPLAY button to display the current time.

3 Press the RDS MODE selector button. The title of function ON CT > CLOCK is displayed.

4 Select the title of function whose setting you want to switch by pressing the PTY SEEK MODE button once or more.

5 Switch the function ON or OFF by pressing the PTY SEEK START button, watching the display.

6 Press the RDS MODE selector button again to restore the frequency display mode. * If the station has PS data, after that, it turns into the PS

mode.

Notes Once the setting is changed, it will be stored until it is

changed again by the above operation. During the operation, if there is no operation for about 20

seconds, this mode is canceled and turns into the frequency display. If the station has PS data, after that, it turns into the PS mode.

Receiver 3, 6 4

2 1 5

1

2

3

PTY SEEK

MODE

E-26

Detection hole

Tab

TAPE DECK OPERATION

General information Do not use C-120 tapes or poor-quality tapes, since they

can cause malfunctions. Before loading a tape into the cassette compartment,

tighten the tape slack with a pen or pencil. Tapes have removable tabs which prevent accidental

recording or erasing from taking place. Removing the tab on the top left protects the side facing you from erasure. Cover the tab holes with adhesive tape to erase or record again.

This deck is a Double Cassette Deck with Automatic Reverse Function. DECK A: Playback only. DECK B: Playback or recording.

This deck features an auto tape selector. Just load the tape, and the tape formula being used will be sensed automatically.

This unit can play back metal tapes as well as normal or chrome tapes, and recording can also be done on metal tapes.

When covering erasure prevention tab holes, do not cover the chrome and metal detection holes. Otherwise, the deck will treat tape as normal tape.

Do not press the EJECT button during playback or recording.

Tape A or tape B playback 1 Select the TAPE position with the INPUT SELECTOR

control, watching the display.

2 Open the DECK A or DECK B cassette compartment by pressing the EJECT button.

3 Load the tape into the DECK A or DECK B cassette compartment, and close the lid panel completely by pressing the upper part of the center of the panel as figured left. * If you have loaded two tapes into both the DECK A and

B cassette compartments, select the DECK A or B in which the tape you want to play back is loaded by pressing the DECK A or B selector button.

4 Set the Dolby NR switch to B or C if the tape is recorded with Dolby noise reduction, and to OFF if Dolby NR is not used. * For selection of the Dolby B or C position, refer to the

Dolby B and C Type Noise Reduction on page 29.

5 Set the reverse MODE switch as desired.

The reverse MODE switch can be operated before or during playback, and changes tape playback as follows:

6 Press the play button to listen to side A, or the play button for side B.

To stop playback Press the stop button.

Note When removing the tape, press the stop button, and then open the cassette compartment.

Direct operation Even if an input source other than tape deck is selected, pressing the play button (or the fast wind button) will start playback (or fast winding) directly.

E-27

E n

g lish

TAPE DECK OPERATION

3

DECK A selector button

DECK B selector button

Receiver

Tape Deck

2 5 6 6 4 2

1

1 2 3 4 5

CD

6 7 8 6 7 8 9 0

1 2 3 4 5

TIME PROG TAPE EDIT +10

A B C D E

REPEAT RANDOM STOP PLAY/PAUSE OPEN/CLOSE

MODE DISC SKIP TUNER

DECK A/B

PLAY STOP PLAY TAPE

INPUTREC/PAUSE

- +

- +

EFFECT LEVEL SP/PHONES MODE DSS

POWER SLEEP DISPLAY VOLUME 1

6

6

DECK A/B button

Side A only

Side B only

Side A Side B

Side B only

Side A Side B

(Repeats 8 times) Starts from side A.

Side A Side B

(Repeats 8 times) Starts from side B. (Side A is not played at the first time.)

E-28

Winding the tape 1 If during playback, first press the stop button.

2 Next press the fast wind or fast wind button to wind the tape.

3 Press the stop button to stop.

* While winding the tape, the corresponding play direction indicator flashes rapidly.

Note When the tape is wound to the end, this unit will then function as described below, according to the setting of the reverse MODE switch.

: The tape stops at the end. : If the winding direction is , when the tape reaches

the end, playback automatically starts from the reverse side. If the winding direction is , the tape stops at the end.

: When the tape reaches the end, playback automatically starts from the reverse side.

Searching for the beginning of a desired selection Carry out the following operation during playback to find the beginning of a desired selection on the tape.

To listen to the same selection Press the button if the direction of the current playback is . Press the button if the direction of the current playback is .

To listen to the next selection Press the button if the direction of the current playback is . Press the button if the direction of the current playback is .

* While searching, the corresponding play direction indicator flashes slowly.

Notes This function may not work for tapes with

* Material with long pauses or quiet passages. * Low recording levels or excessive noise. * Pauses of less than 4 seconds between selections.

If searching is carried out at the first or the last part of a selection, the desired selection may not be found.

TAPE DECK OPERATION

Tape Deck

1 2 3 4 5

CD

6 7 8 6 7 8 9 0

1 2 3 4 5

TIME PROG TAPE EDIT +10

A B C D E

REPEAT RANDOM STOP PLAY/PAUSE OPEN/CLOSE

MODE DISC SKIP TUNER

DECK A/B

PLAY STOP PLAY TAPE

INPUTREC/PAUSE

- +

- +

EFFECT LEVEL SP/PHONES MODE DSS

POWER SLEEP DISPLAY VOLUME

E-29

E n

g lishContinuous playback

1 Load the tapes into the DECK A and DECK B cassette compartments.

2 Set the reverse MODE switch to .

The reverse MODE switch can be operated before or during playback, and changes tape playback as follows:

3 Press the DECK A or B selector button to select the tape to be played back first.

4 Press the play button to listen to side A, or the play button for side B.

Dolby B and C Type Noise Reduction With cassette tapes, the most noticeable form of noise is high frequency hiss. To reduce this hiss noise, this unit has been equipped with a newly developed Dolby C noise reduction system in addition to its conventional Dolby B NR. Either type of noise reduction may be selected with the switch provided. Dolby B NR has a noise reduction effect of about 10 dB in the high frequency range. The corresponding figure with Dolby C NR is about 20 dB, but this is over the entire range where the human ear is most sensitive to noise (2 kHz to 8 kHz). Also, Dolby C NR has the same noise reduction effect at both high and low signal levels. In addition, Dolby C NR improves the tapes MOL (Maximum Output Level). Dolby noise reduction is a 2 part process that acts both on recording and playback; be sure that the noise reduction button is set to the same position on record and play. * Noise in the source material cannot be reduced with the

Dolby NR system.

TAPE DECK OPERATION

Tape Deck 3

1 2 4 4 1

1 2 3 4 5

CD

6 7 8 6 7 8 9 0

1 2 3 4 5

TIME PROG TAPE EDIT +10

A B C D E

REPEAT RANDOM STOP PLAY/PAUSE OPEN/CLOSE

MODE DISC SKIP TUNER

DECK A/B

PLAY STOP PLAY TAPE

INPUTREC/PAUSE

- +

- +

EFFECT LEVEL SP/PHONES MODE DSS

POWER SLEEP DISPLAY VOLUME

44

3

Tape A Side A B Tape B Side A B

(Repeats 8 times) Starts from Tape A Side A.

Tape A Side A B Tape B Side A B

(Repeats 8 times) Starts from Tape A Side B. (Tape A Side A is not played at the first time.)

Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. DOLBY and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation.

E-30

When recording important selections, be sure to make a preliminary test to ensure that the desired source material is being properly recorded with good sound quality.

The automatic recording level control circuit automatically controls the level of the input signal used for recording.

Adjusting the VOLUME, BALANCE, TREBLE and BASS controls have no effect on the recorded sound. If, however, the DSS is on, DSS effect is recorded along with the source. * Music with DSS effect is suitable for listening to inside a

car etc. The deck which can be used for recording is the DECK B

only. When recording, be sure to load a tape into the DECK B cassette compartment.

CD synchronized recording 1 Select the CD position with the INPUT SELECTOR

control, watching the display, and load the disc to be recorded.

2 Load a tape into the DECK B cassette compartment. * Wind past the beginning part of the tape on which

recording cannot be performed.

3 When recording with the Dolby NR system, set the Dolby NR switch to B or C; if not, set it to OFF. * For selection of the Dolby B or C position, refer to the

Dolby B and C Type Noise Reduction on page 29.

4 Set the reverse MODE switch as desired.

When the tape is set so that side A faces you, recording will be done as follows automatically according to the selected reverse mode.

5 Press the REC/PAUSE button. * The corresponding indicator lights up and the play

direction indicators flash.

6 Start CD playback by pressing the corresponding disc selector button, or by pressing the play/pause / button if the disc is already selected. * Before CD playback begins, recording automatically

begins on the side of the tape now selected.

RECORDING COMPACT DISCS

Receiver

CD Player

Tape Deck

2 4 5 3 2

1 2 3 4 5

CD

6 7 8 6 7 8 9 0

1 2 3 4 5

TIME PROG TAPE EDIT +10

A B C D E

REPEAT RANDOM STOP PLAY/PAUSE OPEN/CLOSE

MODE DISC SKIP TUNER

DECK A/B

PLAY STOP PLAY TAPE

INPUTREC/PAUSE

- +

- +

EFFECT LEVEL SP/PHONES MODE DSS

POWER SLEEP DISPLAY VOLUME

Side A only

Side B only

Side A Side B

Side B only

Side A Side B

Side B only

1

6 6

5

6

1

E-31

E n

g lish

To stop recording temporarily

1 Press the stop button of the CD player.

2 Choose the selection to be recorded next by using the SKIP or button, and then press the play/pause

/ button of the CD player to resume recording (or simply press the track number input button on the remote control transmitter).

To stop recording Press the stop button of the tape deck. (At this time, CD playback will not stop.)

Recording programmed tracks

Programmed tracks from one or more discs can also be recorded in the same way.

1 Program desired tracks from one or more discs. (Refer to page 15. for the programming procedure.)

2 Follow steps 25 on the previous page.

3 Press the play/pause / button of the CD player.

Notes During CD Synchronized Recording, when more than 4

seconds elapse between tracks, the tape will stop automatically and resume recording when the beginning of the next track is found.

The CD Synchronized Recording will function even when the CD player is turned into random play mode.

RECORDING COMPACT DISCS

CD Player

Tape Deck

1 2 3 4 5

CD

6 7 8 6 7 8 9 0

1 2 3 4 5

TIME PROG TAPE EDIT +10

A B C D E

REPEAT RANDOM STOP PLAY/PAUSE OPEN/CLOSE

MODE DISC SKIP TUNER

DECK A/B

PLAY STOP PLAY TAPE

INPUTREC/PAUSE

- +

- +

EFFECT LEVEL SP/PHONES MODE DSS

POWER SLEEP DISPLAY VOLUME

/

/

E-32

Recording CD(s) on both sides of a tape automatically 1 Select the CD position with the INPUT SELECTOR

control, watching the display, and load the disc to be recorded.

2 Select the disc by pressing the DISC SKIP button.

3 Load a tape into the DECK B cassette compartment.

4 When recording with the Dolby NR system, set the Dolby NR switch to B or C; if not, set it to OFF. * For selection of the Dolby B or C position, refer to the

Dolby B and C Type Noise Reduction on page 29.

5 Set the reverse MODE switch to or .

6 Press the EDIT button. (EDIT appears on the display.) CD playback and recording starts. Recording is carried out on side A and B of the tape continuously. * If the tape has not rewound to the end, it is rewound to

the end rapidly before recording starts. Recording starts from the first part of the tape on which recording can be done.

* A (or B) on the display shows the side of the tape on which recording is being carried out.

* When the recording on side A finishes while a track is being played back, the sound is automatically faded out, and then the recording stops. The recording on side B starts from the beginning of the same track.

Notes When this CD player is in the all disc play mode, if the

tapes total possible recording time is longer than the total playing time of the selected disc, tracks on another disc are recorded continuously. In this case, as many as three discs can be recorded automatically.

During recording, the PLAYXCHANGE button on the CD player is disabled.

The CD players repeat play mode will be canceled during this recording mode.

Recording programmed tracks

Programmed tracks from one or more discs can also be recorded in the same way.

1 Program desired tracks from one or more discs. (Refer to page 15 for the programming procedure.)

2 Follow steps 36 described above.

To stop recording Press the stop button of the tape deck or the CD player.

RECORDING COMPACT DISCS

Receiver

CD Player

Tape Deck

5 4 3

6 1

1 2 3 4 5

CD

6 7 8 6 7 8 9 0

1 2 3 4 5

TIME PROG TAPE EDIT +10

A B C D E

REPEAT RANDOM STOP PLAY/PAUSE OPEN/CLOSE

MODE DISC SKIP TUNER

DECK A/B

PLAY STOP PLAY TAPE

INPUTREC/PAUSE

- +

- +

EFFECT LEVEL SP/PHONES MODE DSS

POWER SLEEP DISPLAY VOLUME

1

2

6

1

1

E-33

E n

g lishAutomatic tape-editing

This convenient feature can be used to program tracks on a disc (or discs) for recording to tape. By only memorizing the tapes total possible recording time, the unit will automatically program tracks or help you to program tracks so they will fit onto the tape with the least amount of unrecorded space remaining at each end of the tape.

To record a disc with the order of tracks unchanged

1 Select the CD position with the INPUT SELECTOR control, watching the display, and load the disc to be recorded.

2 Select the disc by pressing the DISC SKIP button.

3 Load a tape into the DECK B cassette compartment.

4 When recording with the Dolby NR system, set the Dolby NR switch to B or C; if not, set it to OFF. * For selection of the Dolby B or C position, refer to the

Dolby B and C Type Noise Reduction on page 29.

5 Set the reverse MODE switch to or .

6 Press the TAPE button on the remote control transmitter to select the length of the tape to be used. Whenever pressed, C-46, C-54, C-60 and C-90 appear on the display in turn, and next it returns to the normal display mode.

When using tapes other than C-46, C-54, C-60 or C-90 When C-46, C-54, C-60 or C-90 is appearing on the display, input the tape length by using the track number input buttons on the remote control transmitter. (Examples) C-62: Press 6 and then 2. C-30: Press 3 and then 0, or press +10 three times

and then 0.

7 Press the EDIT button. (EDIT appears on the display.) The following internal operations are carried out before recording is automatically started. * If the tape has not rewound to the end, it is rewound to

the end rapidly before recording starts.

1)Tracks on the disc are automatically divided between side A and side B. You can check the process by watching the display.

2)The end part of the tape on which recording cannot be done is wound.

3)CD playback and recording starts. Recording is carried out on both side A and B of the tape.

off C-46 C-54 C-60 C-90

RECORDING COMPACT DISCS

Receiver

CD Player

Tape Deck

5 4 3

7 1

1

1 2 3 4 5

CD

6 7 8 6 7 8 9 0

1 2 3 4 5

TIME PROG TAPE EDIT +10

A B C D E

REPEAT RANDOM STOP PLAY/PAUSE OPEN/CLOSE

MODE DISC SKIP TUNER

DECK A/B

PLAY STOP PLAY TAPE

INPUTREC/PAUSE

- +

- +

EFFECT LEVEL SP/PHONES MODE DSS

POWER SLEEP DISPLAY VOLUME

6

7

2

6

1

1

E-34

RECORDING COMPACT DISCS

Notes When this CD player is in the all disc play mode, if the

tapes total possible recording time is longer than the total playing time of the selected disc, tracks on another disc are recorded continuously. In this case, as many as three discs can be recorded automatically.

The CD players repeat play mode will be canceled during this recording mode.

To cancel tape-editing function Before recording, press the stop button of the CD player.

To stop recording Press the stop button of the tape deck or the CD player.

To make this unit program tracks on a disc automatically so that the least amount of unrecorded space remains on the tape

1 Follow steps 16 on the previous page.

2 Press the PROG button.

3 Press the TAPE button. AP A> will light up during programming for side A, and AP B> will light up during programming for side B.

* After AP B> goes out from the display, you can check the programmed contents for side A and B respectively. To check, cancel or correct program data, refer to page 16.

4 Press the EDIT button. (EDIT appears on the display.) The recording automatically starts.

CD player

Tape Deck

1 2 3 4 5

CD

6 7 8 6 7 8 9 0

1 2 3 4 5

TIME PROG TAPE EDIT +10

A B C D E

REPEAT RANDOM STOP PLAY/PAUSE OPEN/CLOSE

MODE DISC SKIP TUNER

DECK A/B

PLAY STOP PLAY TAPE

INPUTREC/PAUSE

- +

- +

EFFECT LEVEL SP/PHONES MODE DSS

POWER SLEEP DISPLAY VOLUME

4

2 3

4

E-35

E n

g lish

RECORDING COMPACT DISCS

To record programmed tracks from one or more discs

1 Select the CD position with the INPUT SELECTOR control, watching the display, and load a disc (or discs) on the disc table.

2 Follow steps 36 on page 33.

3 Press the PROG button. * PROGRAM and P-01 light up on the display, and all

track numbers on the selected disc begin flashing.

4 If necessary, select a desired disc by pressing the DISC SKIP button.

5 Select the desired track number by pressing the track number input buttons.

6 Repeat steps 4 and 5 to program more selections for the side A of the tape. You can select the same track again. * Pressing the TIME button displays the total remaining

time on the side of the tape for about 1 second, and then it is replaced by the display of the next playback order.

* If ERR appears on the display, the track number just selected cannot be programmed because there is not enough time remaining on the side A of the tape. However, at this time, if any other track number is flashing continuously on the display, you can program it instead of the unprogrammable one.

7 After you finish the programming for the side A, press the TAPE button. * Pu appears on the display, then you can begin

programming for side B.

8 Repeat steps 4 and 5 to program selections for the side B of the tape. You can select the same track again. * If ERR appears on the display, the track number just

selected cannot be programmed because there is not enough time remaining on the side B of the tape. However, at this time, if any other track number is flashing continuously on the display, you can program it instead of the unprogrammable one.

9 Press the EDIT button. (EDIT appears on the display.) The recording automatically starts.

Notes on tape-editing If programs are made selecting tracks from more than one

disc, during recording, the PLAYXCHANGE button on the CD player is disabled.

To check, cancel or correct program data, refer to page 16.

The maximum number of tracks that can be programmed is 20.

This function can be used to program up to track number 20. If the disc has more than 20 tracks, track number 20 and thereafter will not be programmed.

Receiver

CD Player

Display information during programming

1 2 3 4 5

CD

6 7 8 6 7 8 9 0

1 2 3 4 5

TIME PROG TAPE EDIT +10

A B C D E

REPEAT RANDOM STOP PLAY/PAUSE OPEN/CLOSE

MODE DISC SKIP TUNER

DECK A/B

PLAY STOP PLAY TAPE

INPUTREC/PAUSE

EFFECT LEVEL SP/PHONES MODE DSS

PROGRAM

A 2 3 4 5 6 7 8 9 10

11 12

1

REMAIN

PROGRAM

A 2 3 4 5 6 7 8 9 10

11 12

1

1

9 1

3 7 4

5

9

1

Selected disc

Side of the tape Next playback order

Selected track number

Total remaining time on the side of the tape

Programmed track numbers light up and unprogrammed ones flash.

TIME 1

TIME

E-36

When recording important selections, be sure to make a preliminary test to ensure that the desired source material is being properly recorded with good sound quality.

The automatic recording level control circuit automatically controls the level of the input signal used for recording.

Adjusting the VOLUME, BALANCE, TREBLE and BASS controls have no effect on the recorded sound. If, however, the DSS is on, DSS effect is recorded along with the source. * Music with DSS effect is suitable for listening to inside a

car etc. The deck which can be used for recording is the DECK B

only. When recording, be sure to load a tape into the DECK B cassette compartment.

Recording from the built-in tuner 1 Select the TUNER position with the INPUT SELECTOR

control, watching the display.

2 Tune to the desired station. (Refer to the TUNING OPERATION on pages 19 and 20.)

3 Load a tape into the DECK B cassette compartment.

4 When recording with the Dolby NR system, set the Dolby NR switch to B or C; if not, set it to OFF. * For selection of the Dolby B or C position, refer to the

Dolby B and C Type Noise Reduction on page 29.

5 Set the reverse MODE switch to to record on only one side, or to (or ) for continuous recording on both sides.

6 Press the REC/PAUSE button. * The corresponding indicator lights up and the play

direction indicators flash.

7 Press the play button to record on side A, or the play button to record on side B.

* For continuous recording on both sides, begin on side A. Recording stops automatically at the end of side B.

To stop recording temporarily

1 Press the REC/PAUSE button.

2 To resume recording, press the play button whose indicator is flashing.

To stop recording Press the stop button.

OTHER RECORDINGS

Receiver

3 5 7, 2 6, 1 7, 2

Tape Deck

4 3

1 2 3 4 5

CD

6 7 8 6 7 8 9 0

1 2 3 4 5

TIME PROG TAPE EDIT +10

A B C D E

REPEAT RANDOM STOP PLAY/PAUSE OPEN/CLOSE

MODE DISC SKIP TUNER

DECK A/B

PLAY STOP PLAY TAPE

INPUTREC/PAUSE

- +

- +

EFFECT LEVEL SP/PHONES MODE DSS

POWER SLEEP DISPLAY VOLUME

1

7, 2

6, 1

7, 2

1

E-37

E n

g lishDubbing

During dubbing, adjusting the VOLUME, BALANCE, TREBLE and BASS controls have no effect on the recorded sound. If, however, the DSS is on, DSS effect is recorded along with the source. * Music with DSS effect is suitable for listening to inside a

car etc. Try to use the same tape formula and length for the

recording tape as for the master tape.

1 Select the TAPE position with the INPUT SELECTOR control, watching the display.

2 Load a prerecorded tape into the DECK A cassette compartment. Insert a blank tape into the DECK B cassette compartment.

3 Set the reverse MODE switch to to record on only one side, or to (or ) for continuous recording on both sides.

4 Press the DUBBING button. * Press NORMAL to dub at normal speed, and HIGH

to dub at about twice the normal speed. * Dubbing will begin from side A regardless of the side

now selected.

To stop dubbing Press the stop button. * Tape A and tape B will stop at the same time.

Note Only tapes originally encoded with Dolby B or C NR will be dubbed onto tapes with Dolby B or C NR encoding. The setting of Dolby NR will have no effect on the recording of tape B during dubbing. However, the playback tonal quality of tape A will change according to the Dolby NR switch position.

Erasing recorded tapes 1 Load the tape to be erased into the DECK B cassette

compartment.

2 Select the TAPE position with the INPUT SELECTOR control, watching the display.

3 Set the reverse MODE switch to to erase only one side and to (or ) to erase both sides.

4 Press the REC/PAUSE button, then press the play button to erase side A of the tape, or the play button to erase side B.

OTHER RECORDINGS

Receiver

Tape Deck

4 3, 3 4 4 2 4 2, 1

1 2 3 4 5

CD

6 7 8 6 7 8 9 0

1 2 3 4 5

TIME PROG TAPE EDIT +10

A B C D E

REPEAT RANDOM STOP PLAY/PAUSE OPEN/CLOSE

MODE DISC SKIP TUNER

DECK A/B

PLAY STOP PLAY TAPE

INPUTREC/PAUSE

- +

- +

EFFECT LEVEL SP/PHONES MODE DSS

POWER SLEEP DISPLAY VOLUME

1, 2

4

4

1, 2

4

E-38

HOW TO USE THE BUILT-IN TIMER

Timer play By using the built-in timer, you can set the time when the unit turns on and a source begins playing automatically, and the time when the unit turns off automatically.

1 Prepare the source to be played.

For tuner: Tune in to the station you will listen to.

For tape deck: Load a tape into the cassette compartment. (If tapes are loaded in both the compartments, tape A takes priority of tape B, and is played back by the timer play.)

For CD player: Load a disc on the disc table. If more than one disc are loaded on the disc table, select the disc by using the disc selector buttons or the DISC SKIP button.

2 Press the DISPLAY button. Whenever the DISPLAY button is pressed, the display mode changes as follows. At each mode, make a setting for the timer play, referring to the setting procedure described below.

Current time (TIMER on/off mode)

Source selecting mode (TAPE, TUNER, CD)

ON TIME/Time setting mode

OFF TIME/Time setting mode

Normal display mode

* The display mode will be changed to the next mode after about 8 seconds elapse automatically. If the mode is changed before the setting is completed, call the mode again by pressing the DISPLAY button once or more.

Setting procedure:

At the display of current time Check to be sure that the current time is correct, and press the TIMER button so that TIMER lights up on the display.

At source selecting mode Select the source (TAPE, TUNER or CD) to be played with the INPUT SELECTOR control. * If TUNER is selected, soon it is changed to the

frequency display mode. In this mode, you can select the station to listen to with the timer play by using the BAND button, A/B/C/D/E button and TUNER PRESET DOWN/UP buttons.

Receiver

1 2 3 4 5

CD

6 7 8 6 7 8 9 0

1 2 3 4 5

TIME PROG TAPE EDIT +10

A B C D E

REPEAT RANDOM STOP PLAY/PAUSE OPEN/CLOSE

MODE DISC SKIP TUNER

DECK A/B

PLAY STOP PLAY TAPE

INPUTREC/PAUSE

- +

- +

EFFECT LEVEL SP/PHONES MODE DSS

POWER SLEEP DISPLAY VOLUME

2

2 1

2

2

E-39

E n

g lish At ON TIME/time setting mode

[ON TIME appears on the display, and soon it is changed to a time setting mode.] Set to the time when you want to begin the timer play by using the HOUR button and the MINUTE button.

At OFF TIME/time setting mode [OFF TIME appears on the display, and soon it is changed to a time setting mode.] If necessary, set to the time when you want to finish the timer play (to turn this unit off) by using the HOUR button and the MINUTE button. Even if you do not set the time, it has already been set so that the timer play finishes after 1 hour.

* The TIMER button functions also in the time (ON TIME or OFF TIME) setting mode. (However, it also turns off the power.)

3 If you will not use this unit until the timer play begins, turn the power off by pressing the POWER switch or the TIMER button.

Note If a timer play setting is made and the power is not turned off, the source set for the timer play will begin playing when the time comes in place of the source played at that time.

To cancel the timer play setting After the timer play is finished, press the DISPLAY button to call the current time. While the current time is displayed, press the TIMER button so that TIMER goes out from the display. If it is not canceled, the system will be turned on at the same time every day, so it can be used as an alarm. However, if you are planning to go out at that time, cancel the timer play setting. * Unless the AC supply lead is unplugged or there is a

power failure for more than 5 minutes, the time set on the timer will be retained until it is reset.

How to make time setting in the ON TIME or OFF TIME mode

For the hour: Press the HOUR button to change the hour to a higher value. Press and hold to change continuously. To change the hour to a lower value, while pressing the TIME ADJ button, press the HOUR button.

For the minute: Use the MINUTE button and operate it in the same way as you did to change the hour.

HOW TO USE THE BUILT-IN TIMER

1 2 3 4 5

CD

6 7 8 6 7 8 9 0

1 2 3 4 5

TIME PROG TAPE EDIT +10

A B C D E

REPEAT RANDOM STOP PLAY/PAUSE OPEN/CLOSE

MODE DISC SKIP TUNER

DECK A/B

PLAY STOP PLAY TAPE

INPUTREC/PAUSE

- +

- +

EFFECT LEVEL SP/PHONES MODE DSS

POWER SLEEP DISPLAY VOLUME

TIME ADJ POWER

Receiver

DISPLAY

TIMER HOUR MINUTE

POWER

DISPLAY

E-40

Timer recording (To record a tuner program) 1 Load a blank tape into the DECK B cassette

compartment.

2 If desired, change the setting of the reverse mode and the Dolby NR position.

3 Tune to the station of which program you want to record.

4 Follow step 2 of the Timer play on page 38 and 39.

* In step , select the TUNER position with the INPUT SELECTOR control, and then press the TIMER REC button. (REC will flash on the display.)

* In step , set the time when you want to begin the timer recording.

* In step , set the time when you want to finish the timer recording.

5 Press the TIMER button. (The power will be turned off automatically.) * If a normal display mode (the state which had been

selected before you began setting the timer recording) is restored before you press the TIMER button, select and follow either of the two methods below. Press the DISPLAY button, and then press the

TIMER button. (The power is still on.) Press the POWER switch to turn the power off, and

then press the TIMER button. (The power is turned off.)

To confirm the timer time setting Press the DISPLAY button.

To cancel the setting of timer recording Press the DISPLAY button once or more so that REC flashes on the display. While REC is flashing, press the TIMER REC button. * Unless the AC supply lead is unplugged or there is a

power failure for more than 5 minutes, the time set on the timer will be retained until it is reset.

Note When the timer recording is finished, the timer setting is automatically canceled to avoid repeating timer recording of the same setting.

HOW TO USE THE BUILT-IN TIMER

Receiver

Tape Deck

2 1

1 2 3 4 5

CD

6 7 8 6 7 8 9 0

1 2 3 4 5

TIME PROG TAPE EDIT +10

A B C D E

REPEAT RANDOM STOP PLAY/PAUSE OPEN/CLOSE

MODE DISC SKIP TUNER

DECK A/B

PLAY STOP PLAY TAPE

INPUTREC/PAUSE

- +

- +

EFFECT LEVEL SP/PHONES MODE DSS

POWER SLEEP DISPLAY VOLUME

POWER

DISPLAY TIMER TIMER REC

INPUT SELECTOR

POWER

TUNER input selector button

DISPLAY

E-41

E n

g lish

HOW TO USE THE BUILT-IN TIMER

1 2 3 4 5

CD

6 7 8 6 7 8 9 0

1 2 3 4 5

TIME PROG TAPE EDIT +10

A B C D E

REPEAT RANDOM STOP PLAY/PAUSE OPEN/CLOSE

MODE DISC SKIP TUNER

DECK A/B

PLAY STOP PLAY TAPE

INPUTREC/PAUSE

- +

- +

EFFECT LEVEL SP/PHONES MODE DSS

POWER SLEEP DISPLAY VOLUME

POWER

DISPLAY AUTO MEMO

POWER

SLEEP

Sleep timer operation This unit can be turned off automatically.

1 Play the desired sound source.

2 Press the SLEEP button. SLEEP appears on the display, and soon it is replaced by 2h00m.

3 Press the SLEEP button repeatedly until the desired sleep time appears on the display. The display will change as described below. [Time is displayed by the hour (h) and the minute (m).]

* The original display mode will resume about 4 seconds after the selection is made.

* The SLEEP indicator will light up to indicate that the sleep timer is on.

4 The unit will turn off automatically when the selected sleep time passes.

To confirm the sleep time setting Press the SLEEP button once. SLEEP appears on the display, and soon it is replaced by the remaining time of the selected sleep time.

To change the sleep time While the SLEEP indicator is being illuminated, press the SLEEP button repeatedly until the desired time appears.

To stop the sleep timer operation Press the POWER switch, or press the SLEEP button repeatedly until OFF SLEEP appears on the display. (The SLEEP indicator will go out.)

To set the sleep time using front panel buttons First press the DISPLAY button to display the current time. Within 7 seconds, press the AUTO MEMO button. Whenever the AUTO MEMO button is pressed, the sleep time changes.

Using the timer and the sleep timer at the same time 1 Prepare timer play. (See page 38 and 39.)

* Do not turn the power of this unit off after the timer setting is finished.

2 Press the SLEEP button and set the sleep time.

When the sleep timer operation finishes, the timer will function to turn the source on at the preset time.

Note Do not make the timer time setting so that the timer will start during sleep timer operation. (Since sleep timer operation has priority, the timer will not operate.)

OFF SLEEP (Sleep timer is off.)

2h00m 1h30m 1h00m 0h30m

Receiver

DISPLAY

E-42

INPUT

AUX 2

R L

AUX 1

Singapore and General models> Other audio units (AUX1 and AUX2)

To connect Connect the output terminals of a video cassette player, LD player, etc. to the AUX1 terminals of this system. (red right channel, white left channel)

To listen to 1 Select the AUX1 position with the INPUT SELECTOR

control, watching the display.

2 Operate the unit connected to the AUX1 terminals.

* Its audio source can be recorded by this systems tape deck.

In the same way, connect another unit to the AUX2 terminals.

Another audio unit (AUX)

To connect Connect the output terminals of a video cassette player, LD player, etc. to the AUX terminals of this system. (red right channel, white left channel)

To listen to 1 Select the AUX position with the INPUT SELECTOR

control, watching the display.

2 Operate the unit connected to the AUX terminals.

* Its audio source can be recorded by this systems tape deck.

Turntable (PHONO)

To connect 1 Connect the output terminals of the turntable to the

PHONO terminals of this system. (red right channel, white left channel)

2 Connect the GND lead of the turntable to the GND terminal of this system.

To listen to 1 Select the PHONO position with the INPUT SELECTOR

control, watching the display.

2 Operate the turntable.

* Its audio source can be recorded by this systems tape deck.

USING EXTERNAL UNITS

GND

INPUT

PHONO

AUX

R L

LD player etc. Video cassette player etc.

Video cassette player etc.

Turntable

E-43

E n

g lishInternal care

Dirty heads, capstans and pinch rollers can cause poor sound and tape jams. Clean these parts with a cotton swab moistened with commercially available head/pinch roller cleaner or isopropyl alcohol, or with a commercially available cleaning tape.

After long use, the decks heads and capstans may become magnetized, causing poor sound. Demagnetize these parts once every 30 hours of playing/recording time by using a commercially available tape head demagnetizer. Read the demagnetizers instructions carefully before use.

External care Periodically clean the surfaces of this system, especially

the top panel of the receiver to prevent the ventilation holes from being blocked with dust etc.

Do not use chemically treated cleaning cloths or other chemicals. (See Precautions.)

MAINTENANCE

DECK A

DECK B

E-44

CAUSE

AC supply lead is not plugged in.

Loose speaker connections.

Internal protection circuit is functioning.

Interference from starting motor of nearby car.

Interference from thermostat of nearby electrical appliance.

Antenna input is too weak due to obstructions or excessive distance from broadcasting station.

Insufficient antenna input.

Preset memory has been erased.

Interference from source such as lightning, flourescent lights, electric motors or thermostat of nearby electrical appliance.

TV or microprocessor is being used nearby.

Radio signal is weak or antenna is not properly connected.

Current time is not set.

The internal microcomputer has been frozen by an external electric shock (lightning, excessive static electricity, etc.) or power supply with low voltage.

Disc is upside down.

Disc is dirty.

Input selector setting is incorrect.

Disc is dirty.

Volume is set too high.

Slack tape wrapped around pinch roller.

Erasure prevention tab is broken off.

Head is dirty.

Head is dirty.

Head has become magnetized.

Tape is worn.

Dolby NR switch is set to wrong position.

Head is dirty.

Head is dirty.

Head has become magnetized.

Tape is worn.

Slack tape coming out of cassette shell.

Tape is creased or torn.

Endless tape is being used.

Silent gaps between selections are too short.

Excessively soft passages in middle of selections.

Conversation etc. is recorded.

Batteries are dead.

Remote control is too far away or is being used at incorrect angle.

Direct sunlight or lighting (of an inverter type of flourescent lamp etc.) is striking the remote control sensor of the main unit.

Remote control is being used near TV set with a remote control sensor.

SYMPTOM

No power even if the POWER switch is pressed.

No sound from one speaker

No sound from speakers.

Excessive static in FM broadcasts.

Noise increases during stereo broadcasts.

Stereo broadcasts are noisy and STEREO indicator blinks on and off.

Cannot select preset stations.

Buzzing or static during AM (LW or MW) broadcasts.

AM (LW or MW) broadcast sensitivity is poor.

Cant set timer.

This unit will not operate properly.

Play will not begin even if disc is loaded.

No sound.

Sound stops suddenly (always at same spot).

Tape wont move during playback or recording.

Cant record.

Sound is distorted or fades out.

Poor sound quality.

Stereo balance is poor.

Excessive noise.

Tape travel stops in middle of playback or recording.

Cant find the beginning of desired selections on tape.

Remote control doesnt work.

TV functions strangely when the remote control is used.

TROUBLESHOOTING

If your unit fails to operate normally, check the following points to determine whether the fault can be corrected by the simple measures suggested. If it cannot, or if the fault is not listed in the SYMPTOM column, disconnect the power cord and contact your authorized YAMAHA dealer or service center for help. Should be service required, the servicer will need all three pieces [RX-S75, CDC-S75, KXW-S75].

REMEDY

Plug in the AC supply lead.

Connect properly.

Unplug the AC supply lead from the wall AC outlet, and then plug in again.

Position the FM antenna as high and as far away from nearby roads as possible. Connect using a coaxial cable.

Check antenna connections.

Install a multi-element type FM antenna if possible.

Install an antenna appropriate for the electric field strength of your area.

Reprogram memory presets.

Problem is difficult to eliminate but can be lessened by grounding MW/LW (AM) loop antenna.

Move away from TV or microprocessor.

Properly connect MW/LW (AM) loop antenna.

Change orientation of MW/LW (AM) loop antenna.

Install an external MW/LW (AM) antenna.

Set current time.

Unplug the AC supply lead from the wall AC outlet, and then plug in again after about one minute.

Load disc label side up.

Clean disc.

Select the CD input position.

Clean disc.

Lower volume.

Take up slack with a pencil before using.

Replace tape or cover erasure prevention hole with cellophane tape.

Clean heads.

Clean heads.

Demagnetize heads with head eraser.

Replace tape.

Set to positions matching those used when tape was recorded.

Clean heads.

Clean heads.

Demagnetize heads with head eraser.

Replace tape.

Take up slack by turning reels with a pencil.

Replace with new tape.

Dont use endless tapes.

The function for searching for the beginning of desired selections wont operate unless the silent gaps between selections are at least four seconds long.

Replace batteries.

Use within 6 m and 60 radius.

Change position of the main unit.

Move TV farther away or cover its remote control sensor.

R E

C E

IV E

R C

D P

L A

Y E

R R

E M

O T

E C

O N

T R

O L

T A

P E

D E

C K

E n

g lish

E-45

SPECIFICATIONS

As a part of policy of continuous improvement, YAMAHA reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units.

Receiver (RX-S75)

Minimum RMS Output Power per Channel 6 ohms, 1 kHz, 0.08% THD ........................................... 55W+55W 6 ohms, 1 kHz, 10% THD

[U.S.A., Canada, Singapore and General models only] ...................................................................................... 75W+75W

DIN Standard Output Power per Channel [Europe model only] 6 ohms, 1 kHz, 1% THD .......................................................... 60W

IEC Power [Europe model only] 6 ohms, 1 kHz, 0.1% THD ....................................................... 55W

Input Sensitivity/Impedance PHONO MM [U.K. and Europe models only] ............................................................................ 2.5 mV/47 k-ohms AUX ................................................................... 390 mV/20 k-ohms

Headphone Output Impedance.......................................... 68 ohms Total Harmonic Distortion (1 kHz)

AUX to SP OUT (27.5W/6 ohms) ......................................... 0.08% Signal to Noise Ratio (IHF-A Network)

AUX .........................................................................................90 dB Tone Control Characteristics

BASS: Boost/cut ................................................... 10 dB (50 Hz) TREBLE: Boost/cut ............................................. 10 dB (20 kHz)

Tuning Range FM

[U.S.A. and Canada models]...................... 87.5 to 107.9 MHz [Australia, U.K., Europe, Singapore and General models] ...................................................................... 87.5 to 108.0 MHz

AM (MW) [U.S.A., Canada and General models] ...... 530 to 1,710 kHz [Australia, U.K., Europe and Singapore models] ...................................................................... 531 to 1,611 kHz

LW [U.K. and Europe models only] .................... 153 to 288 kHz

Usable Sensitivity FM (75 ohms)

(30 dB S/N Quieting, 1 kHz, 100% mod.) [U.S.A., Canada, Singapore and General models] .......................................................................1.2 V (12.8 dBf)

(DIN, Mono, S/N 26 dB) [U.K., Europe and Australia models] ..........................1.5 V

AM (MW)........................................................................ 280 V/m LW ................................................................................. 560 V/m

Power Supply [U.S.A. and Canada models] ............................ AC 120V, 60 Hz [Australia model] .............................................. AC 240V, 50 Hz [U.K., Europe and Singapore models] ............ AC 230V, 50 Hz [General model] ...................... AC 110/120/220/240V, 60/50 Hz

Power consumption [U.S.A. and Canada models] ............................................ 155W [Australia, U.K., Europe and General models] ............... 150W

Dimensions (W x H x D)................................ 280 x 107.5 x 345 mm (11 x 4-1/4 x 13-9/16)

Weight .............................................................. 6.0 kg (13 lbs. 3 oz.)

CD player (CDC-S75)

Power Source ................................... AC supplies from receiver unit Type ................................................. 3 DISC Carousel Auto-changer Signal Readout ........................... Non-contact, 3-beam semi-conductor laser pick-up D/A Converter ................................................................... 1-bit DAC Filter ......................................8-time oversampling 18-bit digital filter Wow and Flutter .........................................Below measurable limits Dimensions (W x H x D)................................ 280 x 107.5 x 323 mm

(11 x 4-1/4 x 12-11/16) Weight ................................................................ 3.8 kg (8 lbs. 6 oz.)

Tape Deck (KXW-S75)

Power Source ................................... AC supplies from receiver unit Type ............... Auto Reverse 4-Track 2-Channel playback/recording

and playback stereo double Cassette Deck Heads ................................................ PB, REC/PB : Hard Permalloy

Erase : Double Gap Ferrite Motors ................................................................ DC servo motor x 2 Wow and Flutter ................................................. 50.19%, W.PEAK

0.09%, W.RMS Fast Winding Time (C-60 Tape) ........................ About 120 seconds Frequency Response (20 dB) ........................................................ 30 15,000 Hz 53 dB (Normal)

30 16,000 Hz 53 dB (CrO2) 30 18,000 Hz 53 dB (Metal)

Signal-to-Noise Ratio .................................. 58 dB (Dolby NR OFF) 66 dB (Dolby B NR ON) 74 dB (Dolby C NR ON)

Harmonic Distortion .......................................... No more than 1.2% Channel Separation (Input Shorted 1 kHz) ................................................................................. More than 40 dB Crosstalk (Input Shorted 125 Hz).......................... More than 55 dB Dimensions (W x H x D)................................ 280 x 117.5 x 326 mm

(11 x 4-5/8 x 12-13/16) Weight ................................................................ 4.2 kg (9 lbs. 4 oz.)

Speaker (NX-S75)

Type .................................................... Active Servo Processing type Speakers ........................................................ 14 cm (5-1/2) woofer

5 cm (2) tweeter 1.1 cm super tweeter

Frequency Range .................................................... 40 20,000 Hz Sound Pressure Level............................................................. 89 dB Maximum Power Handling Capacity........................................ 75W Impedance ............................................................................ 6 ohms Dimensions (W x H x D)................................... 200 x 330 x 239 mm

(7-7/8 x 13 x 9-7/16) Weight ........................................................ 4.5 kg (9 lbs. 14 oz.) x 2

YAMAHA ELECTRONICS CORPORATION, USA 6660 ORANGETHORPE AVE., BUENA PARK, CALIF. 90620, U.S.A. YAMAHA CANADA MUSIC LTD. 135 MILNER AVE., SCARBOROUGH, ONTARIO M1S 3R1, CANADA YAMAHA ELECTRONIK EUROPA G.m.b.H. SIEMENSSTR. 22-34, 25462 RELLINGEN BEI HAMBURG, F.R. OF GERMANY YAMAHA ELECTRONIQUE FRANCE S.A. RUE AMBROISE CROIZAT BP70 CROISSY-BEAUBOURG 77312 MARNE-LA-VALLEE CEDEX02, FRANCE YA

Manualsnet FAQs

If you want to find out how the CDC-S75 Yamaha works, you can view and download the Yamaha CDC-S75 Mini Component System Owner's Manual on the Manualsnet website.

Yes, we have the Owner's Manual for Yamaha CDC-S75 as well as other Yamaha manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Owner's Manual should include all the details that are needed to use a Yamaha CDC-S75. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Yamaha CDC-S75 Mini Component System Owner's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Yamaha CDC-S75 Mini Component System Owner's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Yamaha CDC-S75 Mini Component System Owner's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Yamaha CDC-S75 Mini Component System Owner's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Yamaha CDC-S75 Mini Component System Owner's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.