Yamaha EF2600 v3 Owner's Manual PDF

Pages 36
Year 2007
English en
1 of 36
1 of 36

Summary of Content for Yamaha EF2600 v3 Owner's Manual PDF

Page 3

INTRODUCTION Congratulations on your purchase of your new Yamaha... This manual will provide you with a good basic understanding of the operation and maintenance of this machine... If you have any questions regarding the operation or maintenance of your machine, please consult a Yamaha dealer...

Page 4

ments in product design and quality... Therefore, while this manual contains the most current product information available at the time of printing, there may be minor discrepancies between your engine and this manual... If there is any question concerning this manu- al, please consult your Yamaha deal- er...

Page 5

LABELS ... 3

Page 6

THE PERIOD OF WARRANTY Any new EF- series or EDL-series Yamaha Generator pur- chased for private, non-commercial use from an authorized Yamaha consumer generator dealer in the continental United States will be warranted against defects in material or work- manship for a period two (2) years from date of purchase, subject to exclusions noted herein... Any Yamaha non-commercial generator purchased and utilized for commercial or rental applications will be warranted for a period one (1) year from the date of purchase, subject to exclusions noted herein...

Page 7

The federal government requires each manufac- turer to maintain a complete, up-to-date list of all first purchasers against the possibility of a safety- related defect and recall... This list is compiled from the purchase registrations sent to Yamaha Motor Corporation, U... S... A... by the selling dealer at the time of your purchase... If you should move after you have purchased your new generator, please advise us of your new address by sending a post- card listing your Yamaha model name, engine number, dealer number (or dealers name) as it is shown on your warranty identification, your name and new mailing address... Mail to:

Page 8


Page 9

any to get in your eye(s), see your doctor immedi- ately... If any fuel spills on your skin or clothing, immediately wash with soap and water and change your clothes...

Page 10

9 Keep the machine at least 1 m (3 ft) from buildings or other equipment, or the engine may overheat...

Page 11

w Before the generator can be connected to a build- ings electrical system, a licensed electrician must install an isolation (transfer) switch in the build- ings main fuse box... The switch is the connection point for generator power and allows selection of generator or main line power to the building... This will prevent the generator from charging the main power line (backfeeding) when the main power supply has failed or has been turned off for line repair... Backfeeding can electrocute or injure line maintenance personnel... Also, generator and build- ing electrical system damage can occur when nor- mal operating power returns if unit is used without an isolation switch...

Page 12

DESCRIPTION 1 Fuel tank 2 Fuel tank cap 3 Fuel level gauge 4 Carrying handle 5 Ground (Earth) terminal 6 AC receptacle 7 Oil filler cap 8 Oil drain plug 9 Control panel 0 G... F... C... I receptacle q AC switch (N... F... B... ) w Voltmeter e Engine switch r Oil warning light t Spark plug y Choke lever u Fuel cock i Recoil starter o Air filter cover p Muffler

Page 13

NOTE: If the engine stalls or does not start, turn the engine switch to "ON" position and then pull the recoil starter... If the oil warning light flickers for a few seconds, the engine oil is insufficient... Add oil and restart...

Page 14

G... F... C... I... RECEPTACLE The G... F... C... I... (Ground Fault Circuit Interrupter) 1 shuts off power to the protected receptacles if a ground fault (electrical leak) is detected... If the reset button 2 pops out 3, the equipment plugged into the receptacle may be faulty... If this hap- pens, check the equipment carefully... If the equipment appears to be in good condition, press the reset button firmly until a click is heard... This will restore power... If the reset button pops out again, unplug the equipment immediately... Have the equipment inspected and repaired by a qualified repairperson before attempting to use it again...

Page 15

w The engine and muffler will be very hot after the engine has been run... Avoid touching the engine and muffler while they are still hot with any part of your body or clothing during inspection or repair...

Page 16

ENGINE OIL Make sure the engine oil is at the upper level of the oil filler hole... Add oil as necessary...

Page 17

NOTE: The choke is not required to start a warm engine... Turn the choke lever to the operating position...

Page 18

NOTE: Some precision equipment is voltage sensitive and may require a more uniform voltage supply than portable generators provide... Examples include some medical equipment, personal computers, and some inverters that sense peak and RMS voltage values... Consult the precision-equipment vendor before relying on any portable generator to provide power to such equipment...

Page 19

cC Reduce the load to the specified generator rated output if an AC switch turns off... If it turns off again, consult a Yamaha dealer...

Page 20

STOPPING THE ENGINE NOTE: 9 Turn off any electric devices... 9 Turn the AC switch (N... F... B... ) to the 3 (OFF) posi-

Page 21

* : It is recommended that these items be serviced by a Yamaha dealer... ** : Related to emission control system...

Page 22

cC Use only Yamaha specified genuine parts for replacement... Ask an authorized Yamaha dealer for further attention...

Page 23

CARBURETOR ADJUSTMENT The carburetor is a vital part of the engine... Adjusting should be left to a Yamaha dealer with the profession- al knowledge, specialized data, and equipment to do so properly...

Page 24

2... Remove the oil filler cap... 3... Place an oil pan under the engine... Remove the oil

Page 25

AIR FILTER 1... Remove the air filter cover and element... 2... Wash the element in solvent and dry... 3... Oil the element and squeeze out excess oil...

Page 26

1... Stop the engine... 2... Turn the fuel cock lever to CLOSE... 3... Remove the fuel cock cup and gasket... 4... Clean the cup with solvent and wipe it off... 5... Check the gasket... Replace it if damaged... 6... Reinstall the gasket and fuel cock cup...

Page 27

w The engine and muffler will be very hot after the engine has been run... Avoid touching the engine and muffler while they are still hot with any part of your body or clothing during inspection or repair...

Page 28

G... F... C... I... RECEPTACLE TEST 1... Start the engine... 2... Turn the AC switch (N... F... B... ) to the ON position... 3... Press the test button 1, then check the position of

Page 29

No fuel supplied to combustion chamber... 2 No fuel in tank ... Supply fuel... 2 Fuel in tank ... Fuel cock lever to OPEN... 2 Clogged fuel line ... Clean fuel line... 2 Foreign matter in fuel cock ... Clean fuel cock... 2 Clogged carburetor ... Clean carburetor...

Page 30

9 To prevent FIRE HAZARDS be sure to place the spark plug as far way as possible from the spark plug hole and carburetor area...

Page 31

spoon of SAE 10W30 or 20W40 motor oil into the spark plug hole and reinstall the spark plug... Recoil start the engine by turning over several times (with ignition off) to coat the cylinder walls with oil...

Page 32

The above items and the corresponding acronyms are provided in accordance with U... S... EPA REGULATIONS FOR NEW NONROAD SPARK-IGNITION NONHANDHELD ENGINES and the CALIFORNIA REGULATIONS FOR 1995 AND LATER SMALL OFF- ROAD ENGINES... The acronyms conform to the latest version of the SAEs recommended practice docu- ment J1930, Diagnostic Acronyms, Terms, and Definitions For Electrical/Electronic System...

Page 33

Rated Output kW(HP) r/min 3... 3 (4... 4)/3,600 Operation Hours Hr 7... 8 Fuel Unleaded gasoline Fuel Tank Capacity L (Imp gal, US gal) 11... 0 (2... 42, 2... 91) Engine Oil Quantity L (Imp qt, US qt) 0... 6 (0... 53, 0... 63) Ignition System TCI

Page 34

1 Rotor assembly 2 Stator assembly 3 Voltmeter 4 AC switch (N... F... B... ) 5 G... F... C... I receptacle 6 A... C receptacle 7 Ground (earth) terminal 8 Engine switch 9 Condenser 0 Oil warning unit q T... C... I... unit w Spark plug e Oil level switch

Manualsnet FAQs

If you want to find out how the EF2600 Yamaha works, you can view and download the Yamaha EF2600 v3 Owner's Manual on the Manualsnet website.

Yes, we have the Owner's Manual for Yamaha EF2600 as well as other Yamaha manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Owner's Manual should include all the details that are needed to use a Yamaha EF2600. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Yamaha EF2600 v3 Owner's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Yamaha EF2600 v3 Owner's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Yamaha EF2600 v3 Owner's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Yamaha EF2600 v3 Owner's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Yamaha EF2600 v3 Owner's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.