Contents

Yamaha EF2200iS v2 Owner's Manual PDF

1 of 62
1 of 62

Summary of Content for Yamaha EF2200iS v2 Owner's Manual PDF

Printed in China 2019.051 !

(E)

EF2200iS

OWNERS MANUAL

Read this manual carefully before operating this machine.

7PC-F8199-11LIT-19626-02-71

7PC-F8199-11_cover.indd 1-2 2019/05/10 11:03:44

Cover2

Read this manual carefully before operating this machine. This manual should stay with this machine if it is sold.

7PC-F8199-11_cover.indd 3-4 2019/05/10 11:03:45

Introduction Congratulations on your purchase of your new Yamaha. This manual will provide you with a good basic understanding of the operation and main- tenance of this machine. If you have any questions regarding the operation or maintenance of your machine, please consult a Yamaha dealer.

TIP Yamaha continually seeks advancements in product design and quality.

Therefore, while this manual contains the most current product information available at the time of printing, there may be minor discrepancies between your machine and this manual. If there is any question concerning this manual, please consult a Yamaha dealer.

This manual should be considered a permanent part of this machine and should remain with this machine when resold.

* Product and specifications are subject to change without notice.

PLEASE READ AND UNDERSTAND THIS MANUAL COMPLETELY BEFORE OPER- ATING THE MACHINE.

WARNING

EF2200iS OWNERS MANUAL

2019 by Yamaha Motor Corporation, U.S.A. 1st Edition, May 2019 All rights reserved.

Any reprinting or unauthorized use without the written permission of

Yamaha Motor Corporation, U.S.A. is expressly prohibited.

Printed in China P/N LIT-19626-02-71

7PC-F8199-11.book 1

Important manual information Particularly important information is distinguished in this manual by the following nota- tions.

This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.

A WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.

A NOTICE indicates special precautions that must be taken to avoid damage to the machine or other property.

A TIP provides key information to make procedures easier or clearer.

WARNING

NOTICE

TIP

7PC-F8199-11.book 2

Contents

Safety information................. 1-1 General safety information ............... 1-1

Exhaust fumes are poisonous.......... 1-2

Fuel is highly flammable and poisonous......................................... 1-2

Engine and muffler may be hot ........ 1-3

Electric shock prevention ................. 1-3

Connection notes ............................. 1-4

Connection ....................................... 1-4

Extension cord notes........................ 1-5

Location of important labels ............. 1-6

Controls and features ........... 2-1 Description ....................................... 2-1

Control function ................................ 2-4 Engine switch................................ 2-4 Oil level warning light (Red).......... 2-4 AC switch (N.F.B.) ........................ 2-4 Fuel tank cap ................................ 2-5 Ground (earth) terminal ................ 2-5 Economy control switch ................ 2-5 Power supply display .................... 2-6 Overload indicator light (Red) ....... 2-6 Reset button ................................. 2-6 Fuel tank cap air vent lever........... 2-7 Fuel level gauge ........................... 2-7 Hour meter.................................... 2-7 Boost mode switch........................ 2-8 Twin Tech (parallel running terminal)........................................ 2-8 Accessory socket.......................... 2-9 AC receptacle ............................... 2-9 Carburetor fuel drain cock .......... 2-10 Recoil starter............................... 2-10

Before operation.................... 3-1 Preparation....................................... 3-1

Fuel............................................... 3-1 Engine oil ...................................... 3-2

Pre-operation check ......................... 3-4

Operation................................4-1 Precautions for use .......................... 4-1

Starting the engine........................... 4-1

Stopping the engine ......................... 4-3

Connecting devices via Alternating Current (AC) receptacles ................. 4-4

Connecting devices via the accessory socket ............................. 4-5

Application range ............................. 4-7

High altitude operation ..................... 4-8

Periodic maintenance ...........5-1 The importance of maintenance ...... 5-1

Check before use............................. 5-1

Maintenance chart ........................... 5-1

Engine oil replacement .................... 5-3

Spark plug inspection....................... 5-4

Air filter cleaning .............................. 5-6

Muffler screen and spark arrester cleaning............................................ 5-8

Fuel tank strainer cleaning............. 5-10

Carburetor adjustment ................... 5-10

Storage ...................................6-1 Drain the fuel.................................... 6-1

Engine.............................................. 6-3

Trouble recovery ...................7-1 Troubleshooting ............................... 7-1

Specifications ........................8-1 EF2200iS ......................................... 8-1

Consumer information ..........9-1 Machine identification ...................... 9-1

Identification number records........... 9-1

Exhaust emission control system and components ....10-1 Wiring diagram ....................11-1

7PC-F8199-11.book 1

Contents

Yamaha Extended Service (Y.E.S.).................................. 12-1 Index..................................... 13-1

7PC-F8199-11.book 2

1-1

1

2

3

4

5

6

7

8

9

10

11

12

Safety information

General safety information This generator is not designed for on-board use.

Do not use it while installed on the vehicle.

Do not modify the generator or use it with its parts removed.

Do not allow children to operate the generator.

Be sure to carry the generator only by its carrying handle.

Do not place any obstacles on the generator.

1

1. Carrying handle

7PC-F8199-11.book 1

1-2

Safety information

Exhaust fumes are poisonous Using a generator indoors CAN KILL YOU IN MIN-

UTES. Generator exhaust contains carbon monox- ide. This is a poison you cannot see or smell.

NEVER use inside a home or garage, EVEN IF doors and windows are open.

Only use OUTSIDE and far away from windows, doors, and vents.

Fuel is highly flammable and poison- ous Always turn off the engine when refuelling. Never refuel while smoking or in the vicinity of an

open flame. Take care not to spill any fuel on the engine or muf-

fler when refueling.

Do not leave the generator inside the vehicle or in the trunk.

If you swallow any fuel, inhale fuel vapor, or allow any to get in your eye(s), see your doctor immediately. If any fuel spills on your skin or clothing, immediately wash with soap and water and change your clothes.

When operating or transporting the generator, be sure it is kept upright. If it tilts, fuel may leak from the carburetor or fuel tank.

7PC-F8199-11.book 2

1-3

Safety information

Engine and muffler may be hot Place the generator in a place where pedestrians or

children are not likely to touch the machine.

Avoid placing any flammable materials near the exhaust outlet during operation.

In order to prevent overheating, ensure adequate air- flow by keeping the machine at least 1 m (3 ft) from objects or other equipment.

Do not operate the engine with a dust cover or other objects covering it.

When covering the generator, be sure to do so only after the engine and muffler have completely cooled down.

Electric shock prevention Never operate the engine in rain or snow.

7PC-F8199-11.book 3

1-4

Safety information

Never touch the generator with wet hands or electri- cal shock will occur.

Connect the ground (earth) terminal to a ground source. In order to prevent electrical shock, the gen- erator must be grounded when using an electrical device with a ground plug.

Connection notes Avoid connecting the generator to commercial power

outlet. Avoid connecting the generator in parallel with any

other generator.

Connection

1

1. Ground (earth) terminal

1

2

1

2

1. Correct

2. Incorrect

Before the generator can be connected to a build- ings electrical system, a licensed electrician must install an isolation (transfer) switch in the build- ings main fuse box. The switch is the connection point for generator power and allows selection of generator or main line power to the building. This will prevent the generator from charging the main power line (backfeeding) when the main power supply has failed or has been turned off for line repair. Backfeeding can electrocute or injure line maintenance personnel. Also, generator and build- ing electrical system damage can occur when nor- mal operating power returns if unit is used without an isolation switch.

WARNING

7PC-F8199-11.book 4

1-5

Safety information

Extension cord notes Extension cords should be protected by a tough flexible rubber sheath (IEC 245) or the equivalent to withstand mechanical stresses.

7PC-F8199-11.book 5

1-6

Safety information

Location of important labels Please read the following labels carefully before operating this machine.

TIP Maintain or replace safety and instruction labels, as necessary.

4

5

6

7

8

9

1

2

3

1

2

3

4

5

7PC-F8199-11.book 6

1-7

Safety information

6

7

8

9

AC output 60Hz Rated 1.8kVA

120V Phase Single DC output 12V 3A Fuel Gasoline

EF2200iS

7PC-F4164-10

****

************ ************ ************

7PC-F8199-11.book 7

2-1

1

2

3

4

5

6

7

8

9

10

11

12

13

14

Controls and features

Description

1 Carrying handle (p. 1-1) 7 Recoil starter (p. 2-10)

2 Fuel tank cap air vent lever (p. 2-7) 8 Fuel level gauge (p. 2-7)

3 Fuel tank cap (p. 2-5) 9 Muffler (p. 5-8)

4 Control panel (p. 2-1) 10 Carburetor fuel drain cock (p. 2-10)

5 Engine switch (p. 2-4) 11 Panel opener (p. 3-2)

6 Choke knob (p. 4-1)

1 3

4

5 6

7

2 8

9

10

11

7PC-F8199-11.book 1

2-2

Controls and features

Control panel

Multi-function LED meter

1 Accessory socket (p. 2-9) 5 Twin Tech (parallel running terminal) (p. 2-8)

2 Economy control switch (p. 2-5) 6 Ground (earth) terminal (p. 2-5)

3 Multi-function LED meter (p. 2-1) 7 AC receptacle (p. 2-9)

4 Boost mode switch/Reset button (p. 2-8/p. 2-6)

8 AC switch (N.F.B.) (p. 2-4)

1 Oil level warning light (Red) (p. 2-4) 3 Overload indicator light (Red) (p. 2-6)

2 Output indicator (Green) (p. 2-6)

1

2 3 4 5

6

7 78

2 31

7PC-F8199-11.book 2

2-3

Controls and features

This generator has an integrated multi-function LED meter. Its functions are described as below.

Function Display Description Page

Power supply meter Output indicator(s) come on according to the current power supply.

2-6

Operating time meter Output indicator(s) flash ac- cording to the accumulated operation time.

2-7

Overload warning

Overload indicator light comes on after output indicators come on, when an overload or some malfunctions of connect- ed devices are detected.

2-6

Oil warning Oil level warning light flashes when the engine oil level is too low.

2-4

Boost mode Output indicators come on consecutively when the gener- ator is in boost mode.

2-8

7PC-F8199-11.book 3

2-4

Controls and features

Control function

Engine switch The engine switch controls the ignition system and the fuel cock.

TIP The engine switch of this generator opens and closes the fuel cock simultaneously. You dont need to operate the fuel cock separately.

(RUN) Ignition circuit is switched on, and the fuel cock opens. The engine can be started. (STOP) Ignition circuit is switched off, and the fuel cock closes. The engine will not run.

Oil level warning light (Red) When the oil level falls below the lower level, the oil level warning light flashes and then the engine stops automatically. If the light flashes, stop the engine imme- diately, and add engine oil up to the specified level. Unless you refill with oil, the engine will not start again.

TIP If the oil level warning light flashes even though the engine oil level is sufficient, make sure to place the generator horizontally.

AC switch (N.F.B.) The AC switch (Non-Fuse Breaker) turns off automati- cally when the load exceeds the generator AC rated output.

1 3

2

1. Engine switch

2. (RUN)

3. (STOP)

1

1. Oil level warning light (Red)

1

1. AC switch (N.F.B.)

7PC-F8199-11.book 4

2-5

Controls and features

Fuel tank cap Remove the fuel tank cap by turning it counterclock- wise.

Ground (earth) terminal Ground (earth) terminal connects the earth line for pre- vention of electric shock. When the electric device is grounded, be sure to ground the generator, too. For the grounding, consult a Yamaha dealer.

Economy control switch In order to reduce fuel consumption and operating noise, use the economy control switch.

(ON) When the economy control switch is turned to (ON), the economy control unit regulates the engine speed according to the connected load. The results are better fuel consumption and less noise. (OFF) When the economy control switch is turned to (OFF), the engine runs at the rated speed (4900 r/min) regardless of whether a load is connected or not.

TIP The economy control switch must be turned to

(OFF) when using electric devices that require a

Reduce the load to the specified generator AC rated output if the AC switch (N.F.B.) turns off. If it turns off again, consult a Yamaha dealer.

NOTICE

OFF

O N

1

F E

F E

1. Fuel tank cap

1

1. Ground (earth) terminal

123

1. Economy control switch

2. (ON)

3. (OFF)

7PC-F8199-11.book 5

2-6

Controls and features

large starting current, such as a compressor of a submersible pump.

Economy control does not function when the genera- tor is in warming-up period (See page 4-1).

Power supply display The current power supply level is displayed by the out- put indicators. According to the power supply level, the output indicator(s) will come on.

Overload indicator light (Red) The overload indicator light comes on when electricity over the rated output is required by the connected elec- trical devices, or when the inverter control unit over- heats, or the AC output voltage rises. Then the AC protector will trip, stopping power generation in order to protect the generator and any connected electric devices.

TIP The overload indicator light may come on for a few sec- onds at the first when using electric devices that require a large starting current, such as a compressor of a submersible pump. However, this is not a malfunc- tion.

Reset button If an overload has been detected, the circuit breaker has activated, and the generator output has been stopped, stop any connected electrical devices and hold the reset button for 3 seconds. The breaker will be reset and the output will resume.

1

1. Output indicator (Green)

1

1. Overload indicator light (Red)

1

1. Reset button

7PC-F8199-11.book 6

2-7

Controls and features

Fuel tank cap air vent lever The fuel tank cap is provided with an air vent lever to stop fuel flow. The air vent lever must be turned to ON to run the engine.

ON This will allow fuel to flow to the carburetor and the engine to run. OFF When the engine is not in use, turn the air vent lever to OFF to stop fuel flow.

Fuel level gauge The fuel level gauge shows the amount of the fuel in the fuel tank. Make sure that sufficient fuel is in the fuel tank before the operation.

Hour meter The accumulated operation time is displayed by output indicator lights A and B. To see the time, push the reset button 3 times within 1 second in no-load running.

After one-second absence, the light A flashes every 1000 hours, and the light B flashes every 100 hours. For example, if the light A flashes 2 times and the light B flashes 3 times, it shows that the total opera- tion time is about 2300 hours.

TIP Hour meter does not function when the generators are in parallel operation (Twin Tech).

OFF

O N

2

1

4

3

F E

F E

1. Air vent lever

2. Fuel tank cap

3. ON

4. OFF

OFF

O N 1

F E

F E

1. Fuel level gauge

2

3

1

1. Output indicator light A

2. Output indicator light B

3. Reset button

7PC-F8199-11.book 7

2-8

Controls and features

Boost mode switch The boost mode switch raises up the number of rota- tion of the engine temporarily (for approximately 60 seconds). When using devices that require a large starting current, such as a compressor of a submers- ible pump or refrigerator, use this switch. To enter the boost mode, push the boost mode switch for 3 seconds. To exit the boost mode, push the boost mode switch for 3 seconds again.

TIP After approximately 60 seconds of the boost mode, the generator will return to the normal mode automatically.

Twin Tech (parallel running terminal) Two EF2200iS generators can be operated in parallel to increase the rated output to 3.6 kVA and the rated current to 30.0 A. For parallel operation, use only a special Twin Tech cable (optional equipment) approved by Yamaha; contact your Yamaha dealer for the proper Twin Tech cable. The handling, operation procedure and the notes on usage are described in the Twin Tech cable owners manual included in the Twin Tech cable. Consult a Yamaha dealer for this Twin Tech cable.

1

1. Boost mode switch

1

1. Twin Tech cable

7PC-F8199-11.book 8

2-9

Controls and features

Accessory socket This generator has an accessory socket with a cover. It is suitable for the use with portable electric devices.

AC receptacle This generator has two 5-20R receptacles and one NEMA TT-30 receptacle. Before connection, confirm the shapes of the consents and the specifications of both the generator and the devices to be connected.

To avoid severe damage to the generators or other equipment: Never attempt to parallel Yamaha generators of

different outputs or a Yamaha generator with any other brand.

Connect the Twin Tech cable to the generators before starting the generators and turn off the generators before disconnecting them. Never connect the Twin Tech cable to running genera- tors or disconnect them from the generators dur- ing parallel operation.

Do not use Twin Tech cable with only one gener- ator or with just one generator running.

Never allow the Twin Tech cable to hang close to the exhaust side of the generator. Heat from the exhaust could damage the Twin Tech cable.

Do not attempt to modify the Twin Tech cable in any way, such as to try to use three generators.

NOTICE

1

1. Accessory socket

1 2 1. AC receptacle (5-20R)

2. AC receptacle (NEMA TT-30)

7PC-F8199-11.book 9

2-10

Controls and features

Carburetor fuel drain cock Carburetor fuel drain cock is used to discharge the remained fuel in the carburetor for long term storage. Before operation, make sure that the carburetor fuel drain cock is in CLOSED.

Recoil starter The recoil starter is used to start the engine. Pull the recoil starter handle slowly until it is engaged, then pull it briskly.

3

2

1

1. Carburetor fuel drain cock

2. CLOSED

3. OPEN

1

1. Recoil starter handle

Pull the recoil starter handle straight unless it breaks by getting caught in a part around it.

Return the recoil starter handle slowly, not to break the parts of the generator due to the impact when the recoil starter handle retracts vigorously by letting go of the hand while pulling the recoil starter handle.

Do not touch the recoil starter handle while the generator is operating.

NOTICE

7PC-F8199-11.book 10

3-1

1

2

3

4

5

6

7

8

9

10

11

12

13

14

Before operation

Preparation

Fuel

1. Stop the engine. (See page 4-3) 2. Place the generator on a level surface.

3. Remove the fuel tank cap.

4. Check the fuel level. 5. If low, fill the tank with fuel.

707-095

Fuel is highly flammable and poisonous. Check Safety information (See page 1-1) carefully before filling.

Do not overfill the fuel tank over the red level of the fuel tank strainer, otherwise it may overflow when the fuel warms up and expands.

Never refuel while smoking or in the vicinity of an open flame.

Refuel after discharging static electricity from the body, in order not to get burnt by letting a spark catch on fire.

After fill the fuel, make sure the fuel tank cap is tightened securely.

Immediately wipe off spilled fuel with a clean, dry, soft cloth, since fuel may deteriorate painted surfaces or plastic parts.

Use only unleaded gasoline. The use of leaded gasoline will cause severe damage to internal engine parts. If foreign materials enter the fuel tank, they may clog the fuel line. Thus, fill the fuel with the fuel tank strainer certainly installed.

WARNING

NOTICE

7PC-F8199-11.book 1

3-2

Before operation

Make sure there is sufficient fuel in the tank. When refueling, be sure to fill the tank up to the LEVEL mark of the fuel tank strainer.

Your Yamaha engine has been designed to use regular unleaded gasoline with a pump octane number ((R + M)/2) of 86 or higher, or research octane number of 91 or higher.

Engine oil

1. Place the generator on a level surface.

2 1

3

4

1. Fuel level

2. Fuel tank strainer

3. Fuel level gauge

4. LEVEL (Red)

5. F (Full)

6. E (Empty)

Recommended fuel: Unleaded gasoline

Fuel tank capacity: Total:

4.7 L (1.24 US gal, 1.03 Imp gal)

6 5

The generator was shipped from the factory with- out engine oil. Do not start the engine for the first time until the oil level has been checked and oil added if necessary.

NOTICE

7PC-F8199-11.book 2

3-3

Before operation

2. Turn the panel openers to disengage the lock, then remove the panel by detaching the hooks.

3. Remove the oil filler cap.

4. Fill the specified amount of the recommended engine oil, and then install and tighten the oil filler cap.

1

2 2

31 1. Panel opener

2. Hook

3. Panel

1

1. Oil filler cap

Do not tilt the generator when adding engine oil. This could result in overfilling and damage to the engine.

Be sure no foreign material enters the crankcase.

NOTICE

1

1. Correct level

Recommended engine oil: Recommended oil brand:

YAMALUBE Available oil grade:

API SE type or higher JASO MA or MB Available viscosity index:

10W-30 or 10W-40 Engine oil quantity:

0.4 L (0.42 US qt, 0.35 Imp qt)

7PC-F8199-11.book 3

3-4

Before operation

5. Install the panel.

Pre-operation check

The condition of a generator is the owners responsibil- ity. Vital components can start to deteriorate quickly and unexpectedly, even if the generator is unused.

TIP Pre-operation checks should be made each time the generator is used.

Carburetor fuel drain cock - Make sure that the cock is closed.

Fuel (See page 3-1) - Check fuel level in fuel tank. - Refuel if necessary.

Fuel line - Make sure that the fuel should not leak from the

generator when turning on the engine switch. - Consult a Yamaha dealer, if necessary.

Engine oil (See page 3-2) - Check oil level in engine. - If necessary, add recommended oil to specified

level. - Check generator for oil leakage.

The point where abnormality was recognized by use - If any abnormal running conditions are observed,

please consult a Yamaha dealer.

If any item in the pre-operation check is not work- ing properly, have it inspected and repaired before operating the generator.

WARNING

7PC-F8199-11.book 4

4-1

1

2

3

4

5

6

7

8

9

10

11

12

13

14

Operation

Precautions for use

TIP Soon after the purchase or after draining the fuel from the carburetor with the carburetor fuel drain cock, the fuel will not be supplied to the entire starting system automatically. Thus, the recoil starter handle may have to be pulled a few times until the engine starts.

Starting the engine 1. While holding the fuel tank cap so that it will not

move, turn the air vent lever to ON.

Never operate the engine in a closed area or it may cause unconsciousness and death within a short time. Operate the engine in a well venti- lated area.

Before starting the engine, do not connect any electric devices.

Clean dusts, dirt or water off the receptacle before use.

The generator was shipped from the factory with- out engine oil. Do not start the engine for the first time until the oil level has been checked and oil added if necessary.

WARNING

NOTICE

OFF

O N1

F E

F E

1. ON

7PC-F8199-11.book 1

4-2

Operation

2. Turn the economy control switch to (OFF), if necessary.

3. Pull the choke knob fully out.

TIP The choke is not required to start a warm engine. Push the choke knob in to the original position.

4. Turn the engine switch to (RUN).

5. Pull the recoil starter handle slowly until it is engaged, then pull it briskly.

1

1. (OFF)

1

1. Choke knob

1 1. (RUN)

Be careful when using recoil starter. In rare cases, the recoil starter handle can be drawn back quickly by the engine kickback.

Pull the recoil starter handle straight unless it breaks by getting caught in a part around it.

Return the recoil starter handle slowly, not to break the parts of the generator due to the impact when the recoil starter handle retracts vigorously by letting go of the hand while pulling the recoil starter handle.

Grasp the carrying handle firmly to prevent the generator from falling over when pulling the recoil starter.

WARNING

NOTICE

7PC-F8199-11.book 2

4-3

Operation

6. After the engine starts, warm up the engine until the engine does not stop when the choke knob is returned to the original position.

TIP When starting the engine, with the economy control switch (ON), and there is no load on the generator: in ambient temperature below 0 C (32 F), the

engine will run at the rated r/min (4900 r/min) for 5 minutes to warm up the engine.

in ambient temperature below 5 C (41 F), the engine will run at the 4900 r/min for 3 minutes to warm up the engine.

The economy control unit operates normally after the above time period, while the economy control switch is (ON).

Stopping the engine 1. Turn off any electric devices.

2. Turn the economy control switch to (OFF), if necessary.

3. Disconnect any electric devices.

4. Turn the engine switch to (STOP).

1

1. Original position

1

1. (OFF)

1

1. (STOP)

7PC-F8199-11.book 3

4-4

Operation

5. Turn the fuel tank cap air vent lever to OFF after the engine has completely cooled down.

Connecting devices via Alternating Current (AC) receptacles

TIP Make sure to ground (earth) the generator. When the electric device is grounded, be sure to ground the generator, too.

1. Start the engine (See page 4-1).

2. Plug in to AC receptacle.

OFF

O N

1

F E

F E

1. OFF

Be sure any electric devices are turned off before plugging them in.

Be sure all electric devices including the lines and plug connections are in good condition before connection to the generator.

Be sure the total load is within generator rated output.

Be sure the receptacle load current is within receptacle rated current.

WARNING

NOTICE

7PC-F8199-11.book 4

4-5

Operation

3. Make sure that all the output indicators and the overload indicator light come on.

4. Make sure that the output indicators and the over- load indicator light once turn off, and then the only one of the output indicators still remains on.

5. Turn the economy control switch to (ON), if nec- essary.

6. Turn on any electric devices.

TIP The economy control switch must be turned to (OFF) to increase engine speed to rated r/min.

Connecting devices via the accessory socket

1 2

1. Output indicator (Green)

2. Overload indicator light (Red)

1

1. (ON)

Be sure any electric devices are turned off before plugging them in.

Be sure all electric devices including the lines and plug connections are in good condition before connection to the generator.

Be sure the total load is within generator rated output.

Be sure the receptacle load current is within receptacle rated current.

WARNING

NOTICE

7PC-F8199-11.book 5

4-6

Operation

TIP Make sure to ground (earth) the generator.

When the electric device is grounded, be sure to ground the generator, too.

This accessory socket is for charging personal devices such as cell phones, GPS units, tablets, etc.

1. Start the engine (See page 4-1).

2. Open the cover, and then plug in to the accessory socket.

3. Turn on the electric device.

7PC-F8199-11.book 6

4-7

Operation

Application range When using the generator, make sure the total load is within rated output of a generator. Otherwise, generator damage may occur.

TIP means below. Application wattage indicates when each device is used by itself. The simultaneous usage of AC and DC power is possible but total wattage should not

exceed the rated output. EX:

The overload indicator light comes on when electricity over the rated output is required by the connected electrical devices, or when the inverter control unit overheats.

AC DC (Accessory

socket)

Power factor 1 0.80.95 0.40.75

(Efficiency 0.85) Rated voltage 12 V Rated current 3 A

1800 W 1440 W 612 W

Generator rated output 1800 VA

Frequency Power factor

AC 1.0 1764 W

0.8 1404 W

DC 36 W (12 V/3 A)

7PC-F8199-11.book 7

4-8

Operation

High altitude operation This engine may require a high altitude carburetor kit to ensure correct engine operation at altitudes above 4000 ft. (1219 meters). If you operate your engine at altitudes above 4000 ft. (1219 meters) consistently, have your local Yamaha dealer perform the neces- sary carburetor modification. This engine should be operated in its original configuration below 4000 ft. (1219 meters) as damage may occur if high altitude carburetor kit is installed and operated below 4000 ft. (1219 meters).

Do not overload. The total load of all electrical appliances must not exceed the total supply range of both AC and DC of the generator. Overloading will damage the generator.

When supplying precision equipment, electronic controllers, PCs, electronic computers, microcomputer-based equipment or battery chargers, keep the gen- erator a sufficient distance away to prevent electrical interference from the engine. Also ensure that electrical noise from the engine does not interfere with any other electrical devices located near the generator.

If the generator is to supply medical equipment, advice should first be obtained from the manufacturer, a medical professional or hospital.

Some electrical appliances or general-purpose electric motors have high start- ing currents, and cannot therefore be used, even if they lie within the supply ranges given in the above table even though you use the boost mode switch. Consult the equipment manufacturer for further advice.

NOTICE

7PC-F8199-11.book 8

5-1

1

2

3

4

5

6

7

8

9

10

11

12

13

14

Periodic maintenance

The importance of maintenance Safety is an obligation of the owner. Periodic inspection, adjustment and lubrication will keep your generator in the safest and most efficient condition possible. The most impor- tant points of generator inspection, adjustment, and lubrication are explained on the fol- lowing pages.

Check before use The customer needs to perform the pre-operation check (See page 3-4). If any problems are discovered during the inspection, contact a Yamaha dealer and request an inspection or maintenance.

Maintenance chart

If you are not familiar with maintenance work, have a Yamaha dealer do it for you.

Stop the engine before starting maintenance work.

Use only Yamaha specified genuine parts for replacement. Ask an authorized Yamaha dealer for further information.

Item Routine Pre-op- eration check

Every

6 months or 100 Hrs

12 months 300 Hrs

Engine oil Check oil level in engine. Replace. (*1)

Fuel Check fuel level and leak-

age.

Fuel hose Visual inspection.

Check for cracks or dam- age with fingers.

Spark plug Clean and replace if nec-

essary.

Air filter Check for cracks or dam-

age. Clean. (*2)

Muffler screen Check condition.

WARNING

WARNING

NOTICE

7PC-F8199-11.book 1

5-2

Periodic maintenance

*1 Initial replacement of the engine oil is after one month or 20 hours of operation. *2 Needs to be cleaned more frequently when using in unusually wet or dusty areas.

Since these items require special tools, data and technical skills, have a Yamaha dealer perform the service.

Fuel tank strainer Check for dirt and clog-

ging. Clean if necessary.

Check for cracks.

Fuel cock strainer Remove the cock, check

for clogging, and clean if necessary.

Breather hose Check for poor connec-

tion.

Cylinder head Decarbonize cylinder

head.

Intake/Exhaust valves Check and adjust valve

clearance.

Recoil starter Check for fine splits and

damage.

Outer covers Check outer covers for in-

stallation and damage.

Fittings/fasteners Check that bolts are se-

curely fastened. Fasten them if necessary.

Output voltage Check that output indica-

tors are on.

Visual inspection for potential damage

Item Routine Pre-op- eration check

Every

6 months or 100 Hrs

12 months 300 Hrs

7PC-F8199-11.book 2

5-3

Periodic maintenance

Engine oil replacement

1. Place the generator on a level surface and warm up the engine for several minutes. Then stop the engine, then turn the engine switch to (STOP) and fuel tank cap air vent lever to OFF.

2. Turn the panel openers to disengage the lock, then remove the panel by detaching the hooks.

3. Remove the oil filler cap.

4. Place an oil pan under the engine. Tilt the genera- tor to drain the oil completely.

5. Check the oil filler cap and O-ring. Replace them if damaged.

Avoid draining the engine oil immediately after stopping the engine. The oil is hot and should be handled with care to avoid burns.

WARNING

1

2 2

31 1. Panel opener

2. Hook

3. Panel

2

1

1. Oil filler cap

2. O-ring

7PC-F8199-11.book 3

5-4

Periodic maintenance

6. Place the generator on a level surface. 7. Add engine oil to the correct level.

8. Wipe the panel clean, and wipe up any spilled oil.

9. Install the O-ring and the oil filler cap. 10. Install the panel.

Spark plug inspection The spark plug is an important engine component, which should be checked periodically.

TIP The spark plug tool is not included with the generator. Please obtain the appropriate 20.8 mm (13/16 in) spark plug wrench.

1

Do not tilt the generator when adding engine oil. This could result in overfilling and damage to the engine.

Be sure no foreign material enters the crankcase.

1. Correct level

Recommended engine oil: Recommended oil brand:

YAMALUBE Available oil grade:

API SE type or higher JASO MA or MB Available viscosity index:

10W-30 or 10W-40 Engine oil quantity:

0.4 L (0.42 US qt, 0.35 Imp qt)

NOTICE

Soon after stopping the engine, do not touch the spark plug and the engine. As they are hot, it may result in a burn.

WARNING

7PC-F8199-11.book 4

5-5

Periodic maintenance

1. Turn the panel openers to disengage the lock, then remove the panel by detaching the hooks.

2. Remove the spark plug cap and access cap, and insert the tool through the hole from the outside of the cover.

3. Insert the handlebar into the tool and turn it coun- terclockwise to remove the spark plug.

4. Check for discoloration and remove the carbon. The porcelain insulator around the center elec- trode of spark plug should be a medium-to-light tan color.

5. Check the spark plug type and gap.

TIP The spark plug gap should be measured with a wire thickness gauge and, if necessary, adjusted to specifi-

1

2 2

31 1. Panel opener

2. Hook

3. Panel

1 2

1. Spark plug cap

2. Access cap

12

1. Tool

2. Handlebar

1

1. Spark plug gap

Standard spark plug: BPR6HS (NGK)

Spark plug gap: 0.60.7 mm (0.0240.028 in)

7PC-F8199-11.book 5

5-6

Periodic maintenance

cation.

6. Install the spark plug.

TIP If a torque wrench is not available when installing a spark plug, a good estimate of the correct torque is 1/41/2 turn past finger tight. However, the spark plug should be tightened to the specified torque as soon as possible.

7. Install the spark plug cap and access cap.

8. Install the panel.

Air filter cleaning 1. Turn the panel openers to disengage the lock, then

remove the panel by detaching the hooks.

2. Remove the screw and then remove the air filter case cover.

Spark plug tightening torque: 20 Nm (2.0 kgfm, 15 lbft)

1

2 2

31 1. Panel opener

2. Hook

3. Panel

1

2 1. Screw

2. Air filter case cover

7PC-F8199-11.book 6

5-7

Periodic maintenance

3. Remove the foam element.

4. Wash the foam element with a foam air filter cleaner and dry it.

5. Oil the foam element and squeeze out excess oil. The foam element should be wet but not dripping.

6. Insert the foam element into the air filter case.

2

3

1

1. Screw

2. Air filter case cover

3. Foam element

Do not wring out the foam element when squeezing it. This could cause it to tear.

Recommended oil: Foam air filter oil or equivalent oil

The engine should never run without the foam ele- ment; excessive piston and cylinder wear may result.

NOTICE

NOTICE

7PC-F8199-11.book 7

5-8

Periodic maintenance

TIP Be sure the foam element sealing surface matches the air filter so there is no air leak.

7. Install the air filter case cover in its original position and tighten the screw.

8. Install the panel.

Muffler screen and spark arrester cleaning

1. Remove the muffler cover bolts, and then remove the muffler cover.

2. Loosen the muffler cap bolt and then remove the muffler cap, muffler cap band and muffler screen.

3. Use a flathead screw driver to pry the spark arrester out from the muffler.

The engine and muffler will be very hot after the engine has been run. Avoid touching the engine and muffler while they are still hot with any part of your body or clothing during inspection or repair.

WARNING

1

2

1 1. Muffler cover bolt

2. Muffler cover

1

2 3

4

1. Muffler cap bolt

2. Muffler cap

3. Muffler screen

4. Muffler cap band

7PC-F8199-11.book 8

5-9

Periodic maintenance

4. Remove the spark arrester.

5. Remove the carbon deposits on the muffler cap, muffler screen and spark arrester using a wire brush.

6. Check the muffler screen and spark arrester. Replace them if damaged.

7. Install the spark arrester.

TIP Align the spark arrester projection to the hole in the muffler pipe.

8. Install the muffler screen, muffler cap and muffler cap band, and then tighten the muffler cap bolt.

9. Install the muffler cover and tighten the muffler cover bolts.

1 1. Spark arrester

711-075 When cleaning, use the wire brush lightly to avoid damaging or scratching of the muffler cap, muffler screen and spark arrester.

NOTICE

1

2 1. Spark arrester projection

2. Hole

Muffler cap bolt tightening torque: 3.5 Nm (0.35 kgfm, 2.6 lbft)

Muffler cover bolt tightening torque: 7 Nm (0.7 kgfm, 5.2 lbft)

7PC-F8199-11.book 9

5-10

Periodic maintenance

Fuel tank strainer cleaning

1. Remove the fuel tank cap and fuel tank strainer.

2. Clean the fuel tank strainer with gasoline. Replace it if damaged.

3. Wipe the fuel tank strainer and insert it.

4. Install the fuel tank cap.

Carburetor adjustment The carburetor is a vital part of the engine. Adjusting should be left to a Yamaha dealer with the professional knowledge, specialized data, and equipment to do so properly.

Never use gasoline while smoking or in the vicinity of an open flame.

WARNING

2

1 1. Fuel tank cap

2. Fuel tank strainer

Be sure the fuel tank cap is tightened securely. WARNING

7PC-F8199-11.book 10

6-1

1

2

3

4

5

6

7

8

9

10

11

12

13

14

Storage

Long term storage of your machine will require some preventive procedures to guard against deterioration.

Drain the fuel 1. Turn the engine switch to (STOP).

2. Remove the fuel tank cap and fuel tank strainer. Extract the fuel from the fuel tank into an approved gasoline container using a commercially available hand siphon. Then, install the fuel tank strainer and fuel tank cap.

1

1. (STOP)

Fuel is highly flammable and poisonous. Check Safety information (See page 1-1) carefully.

Install the fuel tank cap securely. Immediately wipe off spilled fuel with a rag. Fire

hazard may occur.

Immediately wipe off spilled fuel with a clean, dry, soft cloth, since fuel may deteriorate painted sur- faces or plastic parts.

WARNING

NOTICE

7PC-F8199-11.book 1

6-2

Storage

3. Drain the fuel from the carburetor by turning the carburetor fuel drain cock to OPEN.

TIP When draining the fuel from the carburetor, place the generator on a level surface.

4. After draining the fuel, turn the carburetor fuel drain cock to CLOSED.

5. Slowly pull the recoil starter until compression or resistance is felt, at this point you can slowly allow the recoil starter to return.

6. Turn the fuel tank cap air vent lever to OFF after the engine has completely cooled down.

7. Inspect unit for any loose fasteners or damaged components prior to storage.

8. Store the generator in a dry, well-ventilated place, with the cover placed over it.

2

1 1. Cap

2. Carburetor fuel drain cock

Immediately wipe off spilled fuel with a rag. Fire hazard may occur.

Do not turn the carburetor fuel drain cock with any tools not to break the cock.

WARNING

NOTICE

7PC-F8199-11.book 2

6-3

Storage

Engine Perform the following steps to protect the cylinder, pis- ton ring, etc. from corrosion. 1. Remove the spark plug, pour about one table-

spoon of engine oil (See page 5-3) into the spark plug hole and install and tighten the spark plug to the specified torque. Recoil start the engine by turning over several times (with ignition off) to coat the cylinder walls with oil.

2. Pull the recoil starter until you feel compression. Then stop pulling. (This prevents the cylinder and valves from rusting).

3. Clean exterior of the generator and apply a rust inhibitor.

4. Store the generator in a dry, well-ventilated place, with the cover placed over it.

5. The generator must remain in a vertical position when stored, carried or operated.

7PC-F8199-11.book 3

7-1

1

2

3

4

5

6

7

8

9

10

11

12

Trouble recovery

Troubleshooting This section describes the likely causes and remedies for problems. If your Generator requires repair, bring it to a Yamaha dealer.

Engine wont start

The machine suddenly stopped

Item Check Action Page

Fuel

Is there fuel in the fuel tank? Supply fuel. 3-1

Is the engine switch in (RUN)?

Turn the engine switch to the

(RUN). 2-4

Is the fuel tank cap air vent le- ver closed?

Turn the fuel tank cap air vent lever to the ON.

2-7

Have you drained the fuel ac- cording to the procedure of storage after the previous use?

The fuel line and the carbure- tor may be clogged. Consult a Yamaha dealer.

Engine oil Is the engine oil level low? Add engine oil. 3-2

Spark plug Is the spark plug dirty with car- bon or wet?

Remove carbon or wipe spark plug dry.

5-4

Item Check Action Page

Receptacle(s) Are the device(s) correctly plugged in to the recepta- cle(s)?

Plug in the device(s) correctly. 4-4, 4-5

Output indicator(s) Are the output indicator(s) turned off?

Make sure that the engine is running correctly.

4-1

Overload indicator light

Does the overload indicator light come on?

Make sure that the total watt- age of connected device(s) is within the rated range.

2-6

Is the overload indicator light flashing?

Some malfunctions have been detected. Consult a Yamaha dealer.

7PC-F8199-11.book 1

7-2

Trouble recovery

Output indicator(s) do not come on

Overload indicator light does not turn off

The device(s) that had been working correctly before do not work

Multi-function LED meter flash or come on abnormally

Item Check Action Page

Overload indicator light

Does the overload indicator light come on?

Make sure that the total watt- age of connected device(s) is within the rated range.

2-6

Is the overload indicator light flashing?

Some malfunctions have been detected. Consult a Yamaha dealer.

The reset button does not function even while the over- load indicator light is coming on.

Consult a Yamaha dealer.

Item Check Action Page

Receptacle(s) Are the device(s) plugged out from the receptacle(s)?

Plug out any connected devic- es from the receptacle(s).

Item Check Action Page

Device(s)

Are you using an extension cord?

Connect the device(s) directly without using extension cords.

Do the device(s) stop due to a voltage drop?

It is not recommended to use devices that are sensitive to voltage fluctuation. Also make sure that the total wattage of connected device(s) is within the rated range.

4-7

Display Check Action Page

Are some of the output in- dicator(s) and overload in- dicator light off even when the engine is started?

Consult a Yamaha dealer.

Do the output indicator(s) and the overload indicator light come on for a few seconds immediately after starting the engine?

It is not a malfunction. The multi-function LED meter is in self-diagnostic mode.

7PC-F8199-11.book 2

7-3

Trouble recovery

For any other abnormal operating conditions not covered here, please consult a Yamaha dealer.

After all the output indica- tor(s) come on, the over- load indicator light comes on, then only output indi- cators turn off after a few seconds or a few minutes.

The engine is overload. Dis- connect any devices from the generator, reduce the total wattage within the rated range, and push the reset button for 3 seconds while the overload in- dicator light is coming on.

2-6

Is the oil level warning light flashing?

Add sufficient engine oil. Place the generator on a level sur- face.

3-2

Display Check Action Page

7PC-F8199-11.book 3

8-1

1

2

3

4

5

6

7

8

9

10

11

12

13

14

Specifications

EF2200iS

* Noise level is measured when the economy control switch is turned to (ON). LWA shows the sound power level under the ISO3744 satisfied test conditions. The noise level in dB (A)/7 m is the arithmetic mean value in four directions measured 7 meters away from each side of the generator. The noise level may vary in different environments.

DIMENSIONS:

Overall length 555 mm (21.9 in)

Overall width 300 mm (11.8 in)

Overall height 470 mm (18.5 in)

Dry weight 25 kg (55 lb)

ENGINE:

Engine type Air cooled 4-stroke gasoline OHV

Cylinder arrangement Inclined, 1 cylinder

Displacement 79 cm

Bore Stroke 48.6 43.0 mm (1.91 1.69 in)

Operations run time 4.2 hrs at rated load or 10.5 hrs at 1/4 of rated load

Fuel type Unleaded gasoline

Fuel tank capacity 4.7 L (1.24 US gal, 1.03 Imp gal)

Engine oil quantity 0.4 L (0.42 US qt, 0.35 Imp qt)

Ignition system CDI

Spark plug BPR6HS (NGK)

Spark plug gap 0.60.7 mm (0.0240.028 in)

Noise level* 92 dB/LWA, 5765 dB (A)/7 m

GENERATOR:

AC output

Rated voltage 120 V

Rated frequency 60 Hz

Rated current 15.0 A

Rated output 1.8 kVA

Rated current (in parallel) 30.0 A

Rated output (in parallel) 3.6 kVA

Safety device Electronic + AC protector

DC output

Rated voltage 12 V

Rated current 3 A

Safety device Electronic

7PC-F8199-11.book 1

9-1

1

2

3

4

5

6

7

8

9

10

11

12

Consumer information

Machine identification The machine serial number is stamped in the location as shown.

TIP The first three digits of these numbers are for model identification (PRI-I.D. CODE); the remaining digits are the unit production number (SERIAL No). Keep a record of these numbers for reference when ordering parts from a Yamaha dealer.

Identification number records Record your model type, Primary I.D., and serial num- bers in the spaces provided, to assist you in ordering spare parts from a Yamaha dealer. Also record and keep these I.D. numbers in a separate place in case your machine is stolen. MODEL:

PRI-I.D. CODE:

SERIAL No:

1

1. Machine serial number

7PC-F8199-11.book 1

10-1

1

2

3

4

5

6

7

8

9

10

11

12

13

14

Exhaust emission control system and components

Item Acronym .......................

.....................

.......................

.................................

The above items and the corresponding acronyms are provided in accordance with U.S. EPA REGULATIONS FOR NEW NONROAD SPARK-IGNITION NONHANDHELD ENGINES and the CALIFORNIA REGULATIONS FOR 1995 AND LATER SMALL OFF- ROAD ENGINES. The acronyms conform to the latest version of the SAEs recommended practice docu- ment J1930, Diagnostic Acronyms, Terms, and Definitions For Electrical/Electronic System.

It is recommended that these items be serviced by a Yamaha dealer.

9 CARB. ASSY., LH. & JT., CARBURETOR2

9 T.C.I. MAGNETO ASSY. & PLUG, SPARK

9 CRANKCASE1 & HEAD, CYLINDER1

9 AIR FILTER ASSY. 9 MUFF., 2, CAP, NET, WIRE2 &

ARRESTER, SPARK

CARB (Carburetor)

EI (Electronic Ignition)

PCV (Positive Crankcase Ventilation) ACL (Air Cleaner)

7PC-F8199-11.book 1

7PC-F8199-11.book 2

11-1

1

2

3

4

5

6

7

8

9

10

11

12

13

14

Wiring diagram

L

L

L

L

L

R B

R B

L

L

L

O

O

L

L

O

O

O O

S

T

R

OO

Y

Y

P

R

R O Y P V L

R O Y P V L

O

V

L

B BrR/W

B BrR/W

Br

B

R/W

B

O

G/Y

Y

R

L

B

O

G/Y

O

Y/B

L/B

Y/B

Y/B

L/B

L/B

G

OP G L V

V LW

WGyBr

Br

G/Y

G/Y

G/Y

W/B

L/B Y/B

L/B Y/B

L/B Y/BBr/B

G V LW Gy

Gy

W/B Br/B

G V LW GyW/B Br/B

P Br

OP G L V WGyBr W/BBr/B

W/BBr/B

G/Y

R

Y

Br

Y

Y Y

YY Y

Y

RBr

R B

R

Br

R

R

Br

Br

Y

Y

Y

BBr

R/W

O

G/Y

32

1

4

p

s

a

gd

f

5

6

8 0

7

q

9

e

w

r

y

t

o

i

u

7PC-F8199-11.book 1

11-2

Wiring diagram

Color code1. Generator

2. DC coil

3. AC sub coil

4. AC coil

5. AC/DC convertor

6. Control box

7. Accessory socket

8. Twin Tech (parallel running terminal)

9. AC receptacle (NEMA TT-30)

10.AC switch (N.F.B.)

11.AC receptacle (5-20R)

12.Multi-function LED meter

13.Economy control switch

14.Boost mode switch/Reset button

15.Ground (earth) terminal

16.Engine switch

17.Fuel cock ground (earth)

18.Control unit

19.Engine

20.Throttle control motor

21.Spark plug

22.CDI unit/Ignition coil

23.CDI magneto

24.Oil level switch

25.Ground (earth) terminal

B Black

Br Brown

G Green

Gy Gray

L Blue

O Orange

P Pink

R Red

V Violet

W White

Y Yellow

Br/B Brown/Black

G/Y Green/Yellow

L/B Blue/Black

R/W Red/White

W/B White/Black

Y/B Yellow/Black

7PC-F8199-11.book 2

12-1

1

2

3

4

5

6

7

8

9

10

11

12

13

14

Yamaha Extended Service (Y.E.S.)

Keep your Yamaha Generator protected even after your warranty expires with genuine Yamaha Extended Service (Y.E.S.).

9 Y.E.S. is designed and administered by Yamaha Motor Corporation to provide maximum owner satis- faction. You get uninterrupted factory-backed coverage for extra peace of mind.

9 Y.E.S. is flexible. You can choose the plan thats right for you: 12 months, 24 months or 36 months coverage.

9 Y.E.S. is administered by the same Yamaha people that handle your warranty - and it shows in the comprehensive coverage benefits. There are no hour limitations and Y.E.S. covers manufacturing defects just like your warranty. See a sample contract at your Yamaha dealer and see how comfort- ing uninterrupted factory backed protection can be.

9 There are no out-of-pocket expenses for covered repairs. Yamaha will never ask you to pay a deductible.

9 Nationwide coverage. Y.E.S. coverage is honored at any authorized Yamaha Outdoor Power Equipment Service dealer.

9 Y.E.S. coverage is transferable to a new owner if you sell or trade-in. That can make you Yamaha much more valuable.

This excellent Y.E.S. plan coverage is only available to Yamaha owners like you, and only while your Yamaha is still within the Yamaha Limited Warranty period. So visit your authorized Yamaha dealer to get all the facts. He can show you how easy it is to protect your investment with Yamaha Extended Service.

Special note: If visiting your dealer isnt convenient, contact Yamaha with your Primary ID number (your frame number). Well be happy to help you get the Y.E.S. coverage you need.

Yamaha Service Marketing P.O. Box 6555

Cypress, CA 90630 1-866-YES-EXTD (1-866-937-3983)

7PC-F8199-11.book 1

13-1

1

2

3

4

5

6

7

8

9

10

11

12

13

14

Index

A Accessory socket ...................................... 2-9 AC receptacle............................................ 2-9 AC switch (N.F.B.)..................................... 2-4 Air filter cleaning........................................ 5-6 Application range ...................................... 4-7

B Boost mode switch.................................... 2-8

C Carburetor adjustment ............................ 5-10 Carburetor fuel drain cock....................... 2-10 Check before use...................................... 5-1 Connecting devices via Alternating Current (AC) receptacles .......................... 4-4 Connecting devices via the accessory socket........................................................ 4-5 Connection................................................ 1-4 Connection notes ...................................... 1-4 Control function......................................... 2-4

D Description ................................................ 2-1 Drain the fuel............................................. 6-1

E Economy control switch ............................ 2-5 Electric shock prevention .......................... 1-3 Engine....................................................... 6-3 Engine and muffler may be hot ................. 1-3 Engine oil .................................................. 3-2 Engine oil replacement.............................. 5-3 Engine switch............................................ 2-4 Exhaust fumes are poisonous................... 1-2 Extension cord notes................................. 1-5

F Fuel ........................................................... 3-1 Fuel is highly flammable and poisonous ... 1-2 Fuel level gauge........................................ 2-7 Fuel tank cap............................................. 2-5 Fuel tank cap air vent lever ....................... 2-7 Fuel tank strainer cleaning ...................... 5-10

G General safety information ........................ 1-1 Ground (earth) terminal............................. 2-5

H High altitude operation .............................. 4-8 Hour meter ................................................ 2-7

I Identification number records.................... 9-1

L Location of important labels.......................1-6

M Machine identification ................................9-1 Maintenance chart .....................................5-1 Muffler screen and spark arrester cleaning .....................................................5-8

O Oil level warning light (Red).......................2-4 Overload indicator light (Red) ....................2-6

P Power supply display .................................2-6 Precautions for use....................................4-1 Pre-operation check...................................3-4 Preparation ................................................3-1

R Recoil starter............................................2-10 Reset button ..............................................2-6

S Spark plug inspection ................................5-4 Specifications, EF2200iS...........................8-1 Starting the engine.....................................4-1 Stopping the engine...................................4-3

T The importance of maintenance ................5-1 Troubleshooting .........................................7-1 Twin Tech (parallel running terminal) ........2-8

7PC-F8199-11.book 1

7PC-F8199-11.book 2

Cover2

Read this manual carefully before operating this machine. This manual should stay with this machine if it is sold.

7PC-F8199-11_cover.indd 3-4 2019/05/10 11:03:45

Printed in China 2019.051 !

(E)

EF2200iS

OWNERS MANUAL

Read this manual carefully before operating this machine.

7PC-F8199-11LIT-19626-02-71 <

Manualsnet FAQs

If you want to find out how the EF2200iS Yamaha works, you can view and download the Yamaha EF2200iS v2 Owner's Manual on the Manualsnet website.

Yes, we have the Owner's Manual for Yamaha EF2200iS as well as other Yamaha manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Owner's Manual should include all the details that are needed to use a Yamaha EF2200iS. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Yamaha EF2200iS v2 Owner's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Yamaha EF2200iS v2 Owner's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Yamaha EF2200iS v2 Owner's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Yamaha EF2200iS v2 Owner's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Yamaha EF2200iS v2 Owner's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.