Yamaha HTR-4063 Firmware Update Guide PDF

1 of 5
1 of 5

Summary of Content for Yamaha HTR-4063 Firmware Update Guide PDF

Firmware Update Procedure for RX-V467/RX-V567

Page.1 of 5

May, 2010 Subject: RX-V467/RX-V567 Firmware Update Version E017

(Including HTR-4063/HTR-5063) Yamaha is pleased to offer the following firmware update to ensure the best possible performance and features for your Yamaha RX-V467/RX-V567 AV Receiver. This firmware adds 3D video pass-through capability for the HDMI connections. Requirements:

A personal computer capable of burning an audio CD BD/DVD/CD player* with digital audio connection

(Optical or Coaxial, not HDMI) *Note CD PLAYER IS PREFERRED. Some DVD players use digital filters, which affects the output signal of the devices. This firmware update may not work with DVD players which use these digital filters. CD players usually do not use these filters.

CHECK THE UNITS FIRMWARE VERSION PRIOR TO THIS UPDATE The firmware version consists of a letter followed by three numbers [ex. E017]. If the three numbers in the firmware version are 017 or higher, you DO NOT need to perform this update. How to check your firmware version: Press and hold the [STRAIGHT] button on the front panel and keep it pressed while you press the [STANDBY/ON] button. Once the front panel displays "ADVANCED SETUP", release the [STRAIGHT] button. Then, press and hold the [TONE CONTROL] button for about 3 seconds until front panel display shows the firmware version. The following pages contain the firmware update instructions for Yamaha AV receivers RX-V467/V567. The outline of the update is as follows:

1. Create an update disc (Audio CD) 2. Connect digital audio with CD, DVD or BD player 3. Enter firmware update mode 4. Play the update disc (Reprogramming) 5. Confirm update firmware version

< IMPORTANT NOTICE > Do not attempt to update your Yamaha receiver using any other data file except those provided directly from the Yamaha website. Follow the instructions carefully and do not attempt any other procedures not specified in the instructions provided by Yamaha. Improperly updated products may cause improper operation, and any parts or service required to restore proper operation will not be covered under the Yamaha Limited Warranty.

Firmware Update Procedure for RX-V467/RX-V567

Page.2 of 5

Instructions for Firmware Update:

STEP1 CREATE UPDATE DISC Download the firmware from YAMAHA website. Unzip and burn the WAV file onto CD-R/RW as an Audio-CD. This will be your update disc.

If you need instructions on creating this firmware update CD, see your Personal

Computer ("PC") CD burning software instructions on how to burn WAV file as an Audio CD.

Note: Conventional CD burning software is recommended. An audio CD burned by Windows Media Player may not work.

STEP2 CONNECT DIGITAL AUDIO WITH BD/DVD/CD PLAYER

Unplug the AC power cable of the receiver from the wall outlet and turn off the power of BD/DVD/CD player. Then, connect CD DVD or BD player* using digital connection (Coaxial or Optical) into any input of your receiver.

*Some DVD players use digital filters, which affects the output signal of the devices. The firmware update will not work with DVD players which use these digital filters. CD players usually do not use these filters, so using a CD player is preferred.

Picture shows an example of the connection. Depending on your BD/DVD/CD player's digital output, connect the receiver with either optical or coaxial.

Firmware Update Procedure for RX-V467/RX-V567

Page.3 of 5

STEP3 ENTER FIRMWARE UPDATE MODE

Plug the AC power cable of the AV receiver. Press and hold the [STRAIGHT] button on the front panel and keep it pressed while you press the [STANDBY/ON] button. Once the front panel displays "Advance Setup", release the [STRAIGHT] button. Then, press and hold the [INFO] button for about 3 seconds until front panel displays CDDA Upgrader. Now your AV receiver is ready for firmware update.

STEP4 START FIRMWARE UPDATE

Turn on the BD/DVD/CD player. Load the Firmware Update CD (Audio CD) and press [PLAY] button on the BD/DVD/CD player. Found Header will appear on the AV receiver for few seconds. Then, the firmware update starts. Found Header appears within 10 seconds from starting update disc playback. In case display doesnt change after 10 seconds, retry the update process again from the beginning or check requirements for the update disc and connection. See IN CASE OF ERROR for details. When completed, Update Success, Please... and Power off!! are displayed repeatedly. Turn off the power of AV receiver.

Stop the BD/DVD/CD player, remove update disc and power off.

While update is in progress, DO NOT interrupt the AV receiver by pressing any buttons or switching off the power.

STANDBY/ON INFO

TONE CONTROL STRAIGHT

Firmware Update Procedure for RX-V467/RX-V567

Page.4 of 5

STEP5 CHECK UPDATED VERSION Press and hold the [STRAIGHT] button on the front panel and keep it pressed while you press the [STANDBY/ON] button. Once the front panel displays "ADVANCED SETUP", release the [STRAIGHT] button. Then, press and hold the [TONE CONTROL] button for about 3 seconds until front panel displays M:E017 7589.

E017: version of firmware 7589: checksum

If your firmware version number and checksum don't match, retry from step 3. Or try the IN CASE OF ERROR method on the last page. Turn off the power of AV receiver.

Congratulations! You have completed the firmware update. Your AV receiver is ready for normal use.

Firmware Update Procedure for RX-V467/RX-V567

Page.5 of 5

IN CASE OF ERROR Case1 Display on the receiver CDDA Upgrader doesnt change after playing the

BD/DVD/CD player.

Check digital cable wiring. Only optical or coaxial connection can be used for this update. HDMI connection will not work.

Check digital out setting. When using DVD/BD players, make sure the digital out is set to PCM. Once update is completed, reset DVD/BD player to its original settings.

Check update disc. Make sure that your CD-R/RW is finalized and created as an AUDIO CD. (playable on any BD/DVD/CD player)

If all above are cleared, your BD/DVD/CD player may not be suited for this update. Try another BD/DVD/CD player or contact your local authorized service center to update the receiver for you.

Case2 Other unintended error occurred.

"ERROR" was displayed during the update Receiver doesn't power up after the update.

Solution: Try the following recovery method

Step PL1. Unplug the AC power cable

Manualsnet FAQs

If you want to find out how the HTR-4063 Yamaha works, you can view and download the Yamaha HTR-4063 Firmware Update Guide on the Manualsnet website.

Yes, we have the Update Guide for Yamaha HTR-4063 as well as other Yamaha manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Update Guide should include all the details that are needed to use a Yamaha HTR-4063. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Yamaha HTR-4063 Firmware Update Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Yamaha HTR-4063 Firmware Update Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Yamaha HTR-4063 Firmware Update Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Yamaha HTR-4063 Firmware Update Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Yamaha HTR-4063 Firmware Update Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.