Yamaha RS60 Drum Rack Assembly Instructions PDF

1 of 4
1 of 4

Summary of Content for Yamaha RS60 Drum Rack Assembly Instructions PDF

*

RS60 RS60

RS60

x1 x1 x1

x1 * 4

x1

x6

x3

RS60

qDTXP DTXPRESS

wTP60

ePCY60

rKP60

tHH60

y FP-700

x2

x10

x1

e e

w

q

w

t y

w

w r

2-4

3

3-1

3-2

3-3

4

4-1

4-2

1

2

2-1

2-2

2-3 DTXPRESS

DTXPRESS

2-4 DTXPRESS

RS60

DTXPRESS

DTXP

2-3

2-1

2-2

3-1

4-1

4-2

3-3

3-2

430-8650 10-1 TEL(053)460-2433

YAMAHA Electronic Drum Rack System Assembly Instructions

Thank you for purchasing the Yamaha Electronic Drum Rack System RS60. Before using, thoroughly read this assembly manual, and use this product safely and correctly.

RS60

* Specifications are subject to change without notice.

* Specifications are subject to change without notice.

PRECAUTIONS Before using, please read this Assembly Instruction sheet,

and use this product in a safe and proper manner. The Electronic Drum Rack System will be used in conjunction

with the electronic drum set, pads, stands and foot pedals. When deciding the area in which you will place the device,

please follow the precautions below. Especially for small children, parents or an instructor should

teach the children the proper manner in which to use the device.

Always set the instrument on a flat and solid surface. Placement on a sloping, unstable surface or on steps may result in the instrument being unstable and over- turning.

Make sure all bolts are tightened firmly. Loose bolts may result in the rack overturning or parts dropping causing injury.

When adjusting the height or angle, do not suddenly loosen the bolt. The pad may drop or rack pipes may slip pinching or causing injury to hands or fingers.

Do not sit or step on the rack. The rack may overturn or be damaged resulting in injury.

The electronic drum set has many pads and stands so do not play or roughhouse around it. You may hit your face or head. Many people roughhousing around the set may result in the set being overturned so chil- dren should refrain from playing around the set.

Depending upon the strength of the earthquake, strong shocks may cause the set to overturn or move about. Stay clear of the set during earthquakes.

If this symbol is ignored and the equipment is used improperly, fatal injury to persons or se- rious damage could occur.

Do not put your hands or feet under the foot pedal or foot switch. They may be pinched resulting in injury.

Watch your fingers when adjusting clamps. They may become pinched resulting in injury.

Be careful around pipe ends and inside the pipe. Metal shavings, etc., may injure your fingers. Do not insert your fingers into the pipe on purpose or for any other reason.

Only attach pads that have been designed for use on the rack. Attaching tom toms or other acoustic drums may damage the clamps; drums may drop, causing injury.

If this symbol is ignored and the equipment is used improperly, there is a danger of injury to persons handling the equipment, and material damage could occur.

To prevent against accidents and injury

Please follow the cautions listed below

Icons are used to indicate and explain the precau-

tions. To promote the safe and proper use of this prod-

uct, and to protect you and others from injury and

loss of personal property.

Please read the precautions after you understand

the meaning of the icons.

Display Symbols

CAUTIONWARNING

Caution (including danger, or warning). This mark indicates cautions in which you should pay close attention to.

Acts indicated with this icon are prohibited and should not be attempted.

This icon indicates acts that you are urged to follow.

For a move flexible snare/Hi-Hat setup, set the pads as shown in the illustration below.

e e

w

q

w

t y

w

w r

Left Side Assembly (x1)

Right Side Assembly (x1)

RS60 Rack Stand Parts

RS60+Pad grouping : Set up example

* Before assembling the rack stand, make sure all of the parts shown below are included.

Pad and Drum Trigger Grouping (option)

qDTXP DTXPRESS Drum Trigger Module

wTP60 Drum Pad

ePCY60 Cymbal Pad

rKP60 Kick Pad

tHH60 Hi-hat Control Pedal

yFoot Pedal * FP-700 etc.

Center Pipe Assembly (x1)

Module Holder (x1) (4 screws included)

Module Holder Clamp (x1)

Hex Rod Cylinder (x6)

Drum Pad Clamp (x3)

Cymbal Holder (x2)

Cable Band (x10)

Tuning Key (x1)

Assembly Instructions (this sheet)

3 Attach the Drum Pad Clamps

3-1 Insert the Hex Rod Cylinder into the Drum Pad Clamp , and tighten the fixing bolt.

3-2 Attach the Drum Pad Clamps to the tom tom and hi-hat lo- cations.

3-3 Insert the Hex Rod Cylinder into the Pads, adjust the angle and secure.

4

1 Attach the Center Pipe Assembly to the Left Side Assembly and the Right Side Assembly , and tighten the fixing bolts.

2

Module Holder

DTXP

Hex Rod Cylinder

Attach the Module Holder Clamp

Left Side Assembly

Attach the Center Pipe

Right Side Assembly

Cymbal Holder

Drum Pad Clamp Hex Rod Cylinder

RS60 Assembly * A screw driver (+ or -) is necessary to complete the assembly.

Over-tightening of the fixing bolts may result in damage. Take care when tightening fixing bolts and screws. When attaching the pads and the DTXPRESS to the rack, make sure their weight is not extremely unbalanced. Also, take into consideration the forces that are applied while playing the RS60 so that it can be played in a stable condition without excessive deflection.

Step 4-2

Step 3-1

Step 4-1

Step 2-1

Step 2-2

Step 2-3 Step 2-4

Step 3-3

Step 3-2

Cymbal Pad

Tighten

Tighten

Tighten

Tighten

After the above assembly is complete, set the Kick Pad, Hi-Hat Con- trol Pedal, etc. into position and connect the necessary cables. To keep cable out of the way while playing, use the supplied Cable Bands to hold the cables to the rack systemss pipes.

Drum Pad Clamp

Cymbal Holder

Left Side Assembly

Attach the Module Holder

2-1 Insert the Hex Rod Cylinder into the Module Holder Clamp , and tighten the fixing bolts.

2-2 Attach the Module Holder Clamp to the Left Side Assembly pipe.

2-3 Attach the DTXPRESS to the Module Holder . With a screw- driver, use the screws included with the Module Holder to at- tach the holder to the bottom of the DTXPRESS.

2-4 Attach the Module Holder (with the DTXPRESS attached) to the Module Holder Clamp .

Attach the Cymbal Holders

4-1 Insert the Cymbal Holders into the Cymbal Holder Clamps that are attach to the left and right sides of the Center Pipe , and tighten all fixing

Manualsnet FAQs

If you want to find out how the RS60 Yamaha works, you can view and download the Yamaha RS60 Drum Rack Assembly Instructions on the Manualsnet website.

Yes, we have the Assembly Instructions for Yamaha RS60 as well as other Yamaha manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Assembly Instructions should include all the details that are needed to use a Yamaha RS60. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Yamaha RS60 Drum Rack Assembly Instructions is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Yamaha RS60 Drum Rack Assembly Instructions consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Yamaha RS60 Drum Rack Assembly Instructions free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Yamaha RS60 Drum Rack Assembly Instructions, simply download the document to your computer. Once downloaded, open the PDF file and print the Yamaha RS60 Drum Rack Assembly Instructions as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.