Yamaha DTX482K Drum Kit Owner's Manual PDF

1

ELECTRONIC DRUM KIT

DTX482K Manual Development Group 2018 Yamaha Corporation

Published 08/2014 POMA*.*-**A0

VAU5550Owners Manual EN

Thank you for purchasing the Yamaha DTX482K! As a high-end model of the DTX402 series, the DTX482K comes standard with three cymbal pads (two crashes and one ride) and the DTX-series XP80 Snare Pad. We recommend that you read this manual carefully so that you can fully take advantage of the advanced and convenient functions of the instrument. We also recommend that you keep this manual in a safe and handy place for future reference.

Before using this product, be sure to read the PRECAUTIONS on pages 4 to 5 on the DTX402K, DTX432K, and DTX452K Owners Manual.

NOTICE Some objects made of rubber and similar materials can easily stain the drumhead of the snare pad. Do not leave such objects in contact with the drumhead for a long period of time. Pay special attention to avoid stacking the pads when putting them in storage, for example.

1. Package Content

After opening up the package containing your electronic drum kit, please verify that all of the following parts are present.

DTX482K Package Content

Rack (Small)Rack (Large)

Pipe for TOM3

Rod for the snare pad

Drum module

Hi-hat holder Cymbal holders (2)

Stopper No Stopper

KP65 Kick pad

Cymbal/hi-hat pads (2) Crash cymbal pad

Sensor (bumps)

HH65 Hi-hat controller FP6110A Foot pedal

Nine-channel snake cable Drum key Cable bands (3) AC adaptor * May not be included depending on your particular area.

Please check youre your Yamaha dealer.

DTX482K Owners Manual (this booklet) DTX402K, DTX432K, and DTX452K Owners Manual KP65 Owners Manual XP70, XP80 Owners Manual

Additional Cymbal pad XP80 Snare Pad

Cymbal pad (1)

Cymbal holder (1) Stopper (1)

Stereo audio cable (1)

XP80 main unit (1) Clamp bolt (1)

Attaching the cymbal holder for the additional cym- bal pad.

1. Loosen the (1, 2) key bolts and detach the pipe for TOM3.

2. Loosen the clamp bolt of the cymbal holder.

3. Slide the holder clamp onto the TOM3 pipe, and lightly tighten the clamp bolt of the cymbal holder.

4. Attach the TOM3 pipe back to the large rack.

5. Tighten the key bolt ( in the above figure) on the large rack and the clamp bolt of the cymbal holder.

w

2

q

e

1

r

Pipe for TOM3

Cymbal holder

Clamp bolt

Clamp bolt

Holder clamp

Pipe for TOM3

Turn the entire large rack over and continue with the assembly by following the instructions on pages 13 and 14 of the DTX402K, DTX432K, and DTX452K Owners Manual

Step 1

Step 2

Step 3

2. Assembly Guide (1/2)

To assemble the DTX482K, refer to this Owners Manual and the DTX402K, DTX432K, and DTX452K Owners Manual

Fully Assembled DTX482K

CAUTION Choose a flat, hard surface on which to

assemble your electronic drum kit.

Take care to avoid mixing up parts or assem- bling them in the wrong direction. In addition, the assembly steps should be completed one at a time in the order described.

The assistance of at least one other person will be required when assembling the elec- tronic drum kit.

Once a piece has been assembled, be sure to tighten the corresponding key bolts.

To disassemble your electronic drum kit, carry out the assembly sequence in reverse.

Step 8

Step 7

Step 6

Step 4

Step 3Step 2

Step 12

Step 9

Step 10

Step 5 Step 9

Step 1

Step 12Step 11

Additional cymbal pad

Continue to the other side.

Cable band position

2

Attaching the XP80 Snare Pad

1. Attach the rod for the snare pad to the small rack, and then tighten the key bolt () by using a tuning key to secure the rod.

2. Lightly screw the clamp bolt into the socket on the snare pad. (Rotate the clamp bolt five to six times.)

3. Attach the XP80 Snare Pad to the rod, and then tighten the clamp bolt to secure the snare pad.

4. Adjust the angle of the snare pad by first loosening the key bolt (1 and 2 in the above figure). Tighten the key bolt securely after the adjust- ment.

Attaching an additional cymbal pad Attaching an additional cymbal pad requires a stopper. By properly attaching the stopper prevents the cymbal pad from spinning during your performance and protects cables from damage.

1. Rotate the cymbal holder upward and tighten the clamp bolt, and then bring the cymbal tilter upward (fig. 1).

2. Loosen the key bolt on the stopper with a tuning key (fig. 2).

3. Remove the wing nut, two felt pads, and the bolt cover from the cymbal holder (fig. 3).

4. Slide the stopper onto the cymbal holders shaft (fig. 4).

5. Screw down the bolt cover to secure it into position (fig. 4).

6. Place the stopper to make full con- tact with the bottom surface of the bolt cover and tighten the key bolt with a tuning key to secure the stop- per (fig. 5).

7. Place one of the felt pads removed at Step 3 to the cymbal holder (fig. 6).

8. Pass the end of the cymbal holder shaft through the large hole at the cen- ter of the cymbal pad, and the stopper pin through the small hole in the cymbal pad (fig. 6).

9. Place the other felt pad on the cymbal holder (fig. 6).

10. Screw the wing nut to secure the pad to the cymbal holder (fig. 6).

Connecting an additional cymbal 1. Connect the L-shaped plug of the stereo phone cable into the [OUTPUT]

jack of the cymbal pad.

2. Connect the other plug to the [PAD > IN] jack on the KP65 kick pad.

CAUTION Leave a gap of about a half inch between the base of the rod and the snare pad.

Step 4

Rod for the snare pad

XP80 Snare PadClamp bolt

Rod for the snare pad

Clamp bolt

XP80 Snare Pad

1

2

Follow the instructions on pages 15 to 17 on the DTX402K, DTX432K, and DTX452K Owners Manual. With , refer to the example for the DTX452K.

Step 5

Step 5

Step 6

Step 7

Step 8

Step 9

Step 10

NOTE If the key bolt was not sufficiently loosened in Step 2, it may not be possible to slide the stopper onto the cymbal holders shaft. If this occurs, loosen the key bolt as much as possible without removing it.

Cymbal holder

cymbal tilter

(fig. 1)

Key bolt Stopper

Tuning key (fig. 2)

Wing nut

Felt pads

Bolt cover

Cymbal holder

(fig. 3) (fig. 4)

Bolt cover

Stopper

Cymbal holder

(fig. 5)

Stopper

Bolt cover

Full contact

NOTE If the stopper pin does not reach the small hole in the cymbal pad, the stopper will not hold the cymbal pad properly. Make sure to secure the stopper position as shown in Step 6.

Cup

Wing nut

Pin

Stopper

Felt pad

Pad

Pad

Felt pad

Bolt cover

Cymbal holder

Cup Smaller hole

Stopper

(fig. 6)

Follow the instructions on pages 18 to 20 on the DTX402K, DTX432K, and DTX452K Owners Manual. For and , refer to the example for DTX452K. Using the cable bands, secure the cables to the kit rack at the

positions.

Step 12 Step 14

Step 11

Step 12

Step 13

Step 14

Cymbal pad

Stereo phone cable

KP65 Kick pad

2. Assembly Guide (2/2)

Before you start using the drum module, power it up while simultaneously pressing number button [8]. Doing this opti- mizes the settings on your drum module for the DTX482K. Once the setup for the DTX482K is complete, there is no need to perform this procedure every time you turn on the drum module.

1. While holding down the number button [8], press [ ] (Sta