Yamaha EF6300iSDE Operation Manual PDF

1

REMOTE CONTROL KIT

Installation and Operation Manual

Congratulations on your purchase of your new Yamaha product. This manual will provide you with a good basic understanding of the operation and installation of this product. If you have any questions regarding the installation or operation of your machine, please consult a Yamaha dealer.

Dealer: These instructions contain important information for future reference and must be given to the customer. Particularly important information is distinguished in this manual by the following notations.

w 8 This kit is designed for use only with the Yamaha generator. Any other use may cause hazardous

operating conditions. 8 Before using the remote control kit, carefully read and understand this manual, the generator's

owner's manual and warning labels attached to the generator. Also, become familiar with the generator operations, safety information and important information.

cC Use this product only in the country where it was purchased from a Yamaha dealer. Use of the remote transmitter may be illegal in other countries.

NOTE: 8 The remote control can be used up to 20 meters (65 feet) away from the generator if there are no

obstacles between them. 8 This communication distance depends on the ambient environment and the situation in which you use the

remote control. The communication distance becomes shorter if there are any obstacles between you and the generator. Also, if you use the remote control near a radio transmitter facility, the radio communication distance may be reduced greatly or the communication itself may fail. 8 If the remote control has a delay in responding or it does not respond at all even when used close by the

generator, the remote control's batteries may be drained or the generator battery may have discharged. Replace dry cell batteries of the remote control (see page 7 for battery checking procedures), or recharge the generator battery. 8 Keep this manual together with the generator's owner's manual, and use them if you have any questions

or problems during operation. If you resell or transfer your generator to another person, remember to give this manual with the generator owner's manual to the new owner.

7XF-2819W-10

Q The Safety Alert Symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

w Failure to follow WARNING instructions could result in severe injury or death to the generator operator, a bystander or a person inspecting or repairing the engine.

cC A CAUTION indicates special precautions that must be taken to avoid damage to the generator or other property.

NOTE: A NOTE provides key information to make procedures easier or clearer.

7XF-2819W-10_0708.indd 1 2008/07/08 15:46:23

2

w Do not touch parts inside the generator when it is operating or after it has stopped. Otherwise an electric shock or burns may occur. Before installing the kit, turn off the engine and wait until the engine and internal parts of the generator have cooled down.

1. Remove two screws and remove the front panel a.

2. Remove nine screws and pull out the control panel b.

cC During removing the control panel, take care not to hang it by its wire leads. It may damage the wire leads and cause damage to the generator. After the screws have been removed from the control panel, pass a wire through a screw hole of the control panel and tie it to the handle. The control panel should be held by the wire.

INSTALLING Parts of remote control kit

Installing procedure

1 2 3 4

6

5

7 8 9

0

a

b

Receiver unit 11

Band 21

Screw 32

Switch label 41

Remote control switch 51

Wire harness 61

Clamp 72

Warning label 81

Remote control transmitter 9

(with dry cell batteries)1

Warning tag 01

7XF-2819W-10_0708.indd 2 2008/07/08 15:46:29

3

3. Remove four screws and remove the meter unit c.

cC To avoid parts becoming damaged by static electricity, discharge the electricity from your body by touching the engine or other metal surface before servicing the meter unit.

4. Disconnect the engine switch coupler d that is attached to the engine switch e.

5. Return the harness of receiver unit 1, and secure the harness using band 2.

6. Remove grommet f temporarily, and pass the receiver unit harness through the grommet.

7. After passing the harness through the hole where the grommet f has been installed, install the receiver unit 1 by screws 3. Install the grommet f in its original position.

cC Make sure that grommet f is secured to its original position.

8. Remove cap g from the control panel, and attach switch label 4 to the panel.

NOTE: Remove cap g by pressing its top and bottom hooks and by pulling the cap outward.

9. Install remote control switch 5 by facing its terminal downward.

10. Connect the coupler of wire harness 6 to the coupler of receiver unit (2 couplers), engine switch (2 couplers), and remote control switch (1 coupler).

c

d

e

f

f

1 1 2

f

1 3

UP

g

5

4

6

6

to receiver unit (4P)

to receiver unit (6P) to remote control switch

to engine switch

to engine switch coupler (wire harness end)

white tape short harness coupler

7XF-2819W-10_0708.indd 3 2008/07/08 15:46:30

4

11. Mount clamps 7 in the white marker tape positions of wire harness 6, and secure them in the control box as shown.

cC Do not mount clamps 7 in any position other than the white marker tape positions of wire harness 6. If doing so, the wire harness may be damaged when the control panel is installed again.

12. Check the operation of remote control. (See "How to use the remote control" page 5.)

NOTE: If the remote control does not operate normally, check the connectors for poor or incorrect connection.

13. Reassemble the meter unit, control panel, and front panel correctly.

cC Take care not to clinch wire leads and wire harness. If so, the wire leads or wire harness may be damaged and it may cause the generator to fail.

NOTE: Make sure that projection h of the fuel cock can engage with slot i of the fuel cock knob, and install the control panel.

14. Attach warning label 8 to the position as shown.

w Do not remove the warning label. Also, keep the label clean.

NOTE: 8 When attaching warning label 8, wipe, clean and degrease

the surface to be pasted. 8 Attach label 8 to the suitable position where it is not hidden

by front panel a.

7

hi

a8

7XF-2819W-10_0708.indd 4 2008/07/08 15:46:31

5

HOW TO USE THE REMOTE CONTROL lNSTRUCTION TO THE USER This device complies with Part 15 of the FCC Rules

Operation of this device is subject to the following two conditions:

(1)This device may not cause harmful interference, and

(2)This device must accept any interference received including interference that may cause undesired operation.

This equipment has been tested and found to compIy with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determinde by turning the equipment off and on, the user in encouraged to try to correct the interference by one or more of the following measures:

8 Reorient or relocate the receiving antenna.

8 Increase the separation between the equipment and receiver.

8 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

8 Consult the dealer or an experienced radio/TV technician for help.

The user is cautioned that changes and modifications made to the equipment without the approval of manufacture could void the user's authority to operate this equipment.

w 8 Keep the remote control transmitter away from children and pets. 8 Do not remove the warning tag attached to the remote control transmitter.

cC 8 The remote control transmitter can be damaged by impacts. Be careful not to drop it or leave it

where it can be struck by other objects. 8 Do not place heavy objects on the remote control transmitter. 8 Do not leave the remote control transmitter in hot places or in direct sunlight. 8 Do not get the remote control transmitter wet or place it on any wet object. 8 Do not modify the remote control transmitter.

Control functions

"ON" button 1 This button starts the generator by pushing twice in a row.

"OFF" button 2 This button stops the generator.

Indicator lamp 3 This lamp lights in a short time when you press the "ON" button or "OFF" button. Also, it lights for approximately 1 second when the start and stop buttons are operated correctly.

Remote control switch 4 Turn this switch to "ON" when you

operate the generator using the remote control.

2

13

4

Model 7XF-86261/86265

Yamaha Motor Powered Products Co., Ltd.

7XF-2819W-10_0708.indd 5 2008/07/08 15:46:33

6

w Accidentally starting the generator with the remote control while it is stored in an enclosed area increases the risk of carbon monoxide poisoning or fire. Turn off the remote control switch at the generator before storage or whenever remote control operation is not expected.

NOTE: When both the engine switch of generator and the remote control switch 4 are in "ON" position, the generator becomes ready to receive signals from the remote control transmitter and you can operate the generator by remote control.

Preparing the remote control of generator 1. Turn the fuel cock knob to "ON". 2. Turn the engine switch to "7" (ON). 3. Turn the remote control switch to "ON".

4. Connect any electric devices to the generator.

cC 8 Be sure all electric devices including the lines and plug connections are in good condition before

connection to the generator. 8 Be sure any electric devices are turned off before plugging it in. 8 Be sure the total load is within generator rated output. 8 Be sure the receptacle load current is within receptacle rated current.

Starting the generator by remote control Push "ON" button 1 of remote control transmitter twice at the 0.5 second-interval. When this operation is correct, indicator lamp 2 of the remote control transmitter lights for approximately 1 second. And, the startup signal is sent to the generator.

NOTE: 8 To prevent an unintentional startup of generator, this model is designed to require pushing the "ON" button

twice in a row when starting the generator. 8 When the button is pushed correctly, the indicator lights for approximately 1 second. However, the lighting

up of the indicator lamp does not mean the generator has started. 8 When the generator receives a startup signal, the starter motor of the generator is rotated. If the engine of

the generator fails to start, the generator automatically retries to start two more times. If the generator did not start after retries, the motor can not be started by remote control. In this case, turn the engine switch of the generator to "OFF". After checking the generator to find out and solve the cause of start failure, turn the engine switch of generator to "ON" again and start the motor by remote control.

Push 0.5 sec.

0.5 sec.

0.5 sec.

1 2

ON

7XF-2819W-10_0708.indd 6 2008/07/08 15:46:33

7

Stopping the generator by remote control Push "OFF" button 1 of the remote control transmitter for longer than 0.5 seconds. When this operation is correct, indicator lamp 2 of the remote control transmitter lights for approximately 1 second. And, the stop signal is sent to the generator.

w When you stopped the generator by remote control, make sure that the generator has stopped completely. A generator running unexpectedly could cause a hazardous condition.

NOTE: When the button is pushed correctly, the indicator lamp stays lit for approximately 1 second. However, the lighting up of the indicator lamp does not mean the generator has stopped.

Canceling the remote control of generator 1. Disconnect any electric devices. 2. Turn the remote control switch to "OFF".

w Accidentally starting the generator with the remote control while it is stored in an enclosed area increases the risk of carbon monoxide poisoning or fire. Turn off the remote control switch at the generator before storage or whenever remote control operation is not expected.

3. Turn the engine switch to "5" (STOP). 4. Turn the fuel cock knob to "OFF".

Checking the voltage level of dry cell batteries When the generator is stopped, hold down "OFF" button 1 of the remote control transmitter for longer than 0.5 seconds. Indicator lamp 2 lights up twice. If the indicator lamp is dark when lighting or if the lamp does not light up, replace the dry cell batteries. Also, if the remote control does not respond sharply or if it does not respond at all, replace its dry cell batteries.

OFF

1

2

1

2

7XF-2819W-10_0708.indd 7 2008/07/08 15:46:34

8

How to replace dry cell batteries

w 8 Use only the specified dry cell batteries with this remote control transmitter. Also, do not mix new

and old dry cell batteries. This could cause dry cell battery cracking or leakage, which could result in fire or personal injury.

8 When loading the dry cell battery, make sure the plus and minus terminals are correctly oriented. Incorrect orientation could cause dry cell battery cracking or leakage, which could result in personal injury or pollution of the surrounding environment.

8 When you dispose the dry cell battery, obey local laws. 8 Keep the dry cell battery away from children and pets.

1. Remove the screws from remote control transmitter, and disassemble it.

2. Take out the dry cell batteries from the direction of a.

3. Insert new dry cell batteries in the direction of b.

Speci ed dry cell battery : CR2032 (3.0 V) button cell battery Quantity : 2

a

b

cC

Make sure placing the dry cell batteries in right direction.

7XF-2819W-10_0708.indd 8 2008/07/08 15:46:35

9

1

Transmit ID to the receiver unit For the user who purchased only the remote control transmitter, need to transmit ID to the receiver after "Installing procedure" page 4.

1

2

1. Remove the front panel and pull out the control panel . (See "Installing procedure" page 2.)

2. Disconnect the short harness coupler 1.

3. Turn the engine stop switch to "ON". 4. Turn the remote control switch to "ON" and within 10

seconds, push the "OFF" button 1 of the transmitter for at least 0.5 seconds. The indicator lamp 2 will come on for approximately 1 second.

5. Turn the remote control switch to "OFF", and then turn the engine stop switch to "STOP".

6. Reconnect the short harness coupler as it was. 7. Check the operation of remote control. (See "How to use

the remote control" page 5.)

NOTE: If the remote control does not operate normally, turn the engine switch to "STOP" and repeat procedure from 2 to 7.

8. Reassemble the control panel and front panel correctly. (See "Installing procedure" page 2.)

ON

OFF

7XF-2819W-10_0708.indd 9 2008/07/08 15:46:35

10

TROUBLESHOOTING The generator does not start by remote control (But the generator can be started

by turning the engine switch to "START"). 8 The operation of "ON" button of remote control transmitter is incorrect. Push the "ON" button twice within one second. (See "Starting the generator by remote control" page

6.)

8 The remote control switch of the generator is in "OFF" position. Turn the remote control switch of the generator to "ON" position. (See "Preparing the remote control of

generator" page 6.) 8 The dry cell batteries of remote control transmitter have discharged.

Replace the dry cell batteries. (See "How to replace dry cell batteries" page 8.) 8 The radio waves do not reach the generator.

Move to another location and try the remote control.

The remote control transmitter is lost. Please consult a Yamaha dealer.

7XF-2819W-10_0708.indd 10 2008/07/08 15:46:36

7XF-2819W-10_0708.indd 11 2008/07/08 15:46:36