Contents

Xerox Document Centre for FlowPort Software Setup Guide PDF

1 of 21
1 of 21

Summary of Content for Xerox Document Centre for FlowPort Software Setup Guide PDF

Chapter1

Chapter2

Xerox Document Centre Setup Guide for FlowPort This document is intended for use by FlowPort System Administrators when configuring the following Xerox Document Centres to scan to a FlowPort server:

Document Centre 240/255/265/460/470/480/490

Document Centre 220/230/332/340/432/420/425/432/440

There are two basic things you must do on the Document Centre:

Designating a repository on the document centre. This is the IP address of the FlowPort server.

Setting up a default scan template.

The procedures in this guide are provided as examples only. Because of firmware differences, the screens you see may be different, however you may use the concepts presented here.

Xerox Document Centre Setup Guide for FlowPort 1

Configuring a Document Centre 240/255/265/460/470/480/490 with Centreware Internet Services

Configuring a Document Centre 240/255/265/460/470/480/490 with Centreware Internet Services

Verify that the Scan-to-File feature is installed on the Document Centre. Print a Configuration sheet and check the installed options list for Scan-to-File. If the Scan-to-File is not listed, contact your Xerox service representative to obtain and install the Scan-to-File kit. You can also call 1-800-ASK-XEROX for information about obtaining and installing this feature.

FlowPort Repository & Template Setup

The Xerox Document Centre uses templates and repositories to control the disposition of scanned documents. Information about these templates and repositories is stored inside the Document Centre and is accessible through the Web server embedded in the device. The Document Centre provides a default template, a number of named template (optional), a default public repository, and four other configurable public repositories.

Templates are shown as choices on the Document Centre Touch Screen. The default template is named @default.xst and it is the first template shown in the template list on the screen. The Xerox Document Centre uses templates and repositories to control the disposition of scanned documents. Information about these templates and repositories is stored inside the Document Centre and is accessible through the Web server embedded in the device. The Document Centre provides a default template, a number of named templates (optional), a default public repository, and four other configurable public repositories.

Templates are shown as choices on the Document Centre Touch Screen. The default template is named @default.xst and it is the first template shown in the template list on the screen.

Repositories are shown as choices for template setup in the Document Centre Web-based administration tool. Each repository has the following settings:

Repository List

Protocols

File Server IP Address

Directory Path

Login Name

Password

2 Xerox Document Centre Setup Guide for FlowPort

Configuring a Document Centre 240/255/265/460/470/480/490 with Centreware Internet Services

FlowPort Repository Setup

The following settings for the Default Repository and Template Pool Setup are recommended.

1 In your Web browsers Address (or Location) box, enter the TCP/IP address of your Document Centre.

2 Click on Properties.

3 In the Properties column (left side of screen), click on the plus (+) sign for the Services folder. The properties for the Document Centre will display as shown below.

Xerox Document Centre Setup Guide for FlowPort 3

Configuring a Document Centre 240/255/265/460/470/480/490 with Centreware Internet Services

4 Click on the plus (+) sign for the Distribution Templates.

5 Click the Repository Setup link.

6 Under Repository Setup, perform the following:

Repository List: Select Document Repository 0. Check with your Xerox Document Centre System Administrator to make sure the Repository is not in use.

NOTE: Depending on the printer software model, there may only be 1 repository. Some models will have Document Repositories of 0-4 or 1-5.

Protocols: Select TCP/IP.

File Server IP Address: Enter the TCP/IP address of your FlowPort server. Contact your Network Administrator if you do not know the address. In some versions, you may need to enter a port number. In this case, enter 21.

Directory Path: Enter /.

Login Name: Enter the guest account user name (NSA is the default guest account user name).

Password: Enter the FTP password twice (nsa is the default guest password).

Note: If you have changed the NSA FTP user name or password in the FlowPort NSA Protocol Service configuration, enter the new user name and password here to enable FTP access.

4 Xerox Document Centre Setup Guide for FlowPort

Configuring a Document Centre 240/255/265/460/470/480/490 with Centreware Internet Services

7 Click on Apply New Settings.

8 A Login window may display. Enter admin for the user name followed by your password. If you do not know your password, contact your printer system administrator.

Note: The user name and password are case sensitive.

FlowPort Template Setup

1 Click on the Services tab. The Job Submission page displays as shown below.

Xerox Document Centre Setup Guide for FlowPort 5

Configuring a Document Centre 240/255/265/460/470/480/490 with Centreware Internet Services

2 Click on the Distribution Templates button.

6 Xerox Document Centre Setup Guide for FlowPort

Configuring a Document Centre 240/255/265/460/470/480/490 with Centreware Internet Services

3 Under the Services tab, click on the [+] new button.

4 In the General settings box, enter the following:

Name: Type FlowPort (or any name that would let users know that this is the FlowPort template. It can be up to eight characters in length).

Description: Type Scan to FlowPort.

Owner: Type your name or the FlowPort administrators name.

Xerox Document Centre Setup Guide for FlowPort 7

Configuring a Document Centre 240/255/265/460/470/480/490 with Centreware Internet Services

5 Review the Scan Settings. Click on Edit if you need to change the default settings.

Text

8 Xerox Document Centre Setup Guide for FlowPort

Configuring a Document Centre 240/255/265/460/470/480/490 with Centreware Internet Services

6 In the Distribution area, specify a Destination. Select Public Internet Folder from the New Destination list, and click add.

Xerox Document Centre Setup Guide for FlowPort 9

Configuring a Document Centre 240/255/265/460/470/480/490 with Centreware Internet Services

7 In the list of Select from Repository Servers, select repository that points to the FlowPort server.

8 Type the Path to Document /

9 Check the Filing Policy New Auto Generate.

10 Document name is DOC.

11 Select the Output Image Format Multi-Page TIFF.

12 Click on Apply New Settings. The Document Centre is ready to use FlowPort.

Note: This setup provides users Guest access (Trusted/Shared) to FlowPort. If a higher authentication level is required, users should use their FlowPort Login sheet.

Testing the FlowPort Template

To check that the Document Centre is ready for FlowPort use, perform the following test:

1 At the Document Centre, place a document in the scanner.

2 Select the FlowPort template and select Scan.

Note: If the Document Centre is properly configured, a DC confirmation sheet will be printed confirming that the scan to FlowPort was successful, otherwise an error report with some specific failure notice will be printed. If the scan to FlowPort was successful a FlowPort confirmation sheet will also print.

10 Xerox Document Centre Setup Guide for FlowPort

Configuring a Document Centre 220/230/332/340/432/420/425/432/440 with Centreware Internet Services

Configuring a Document Centre 220/230/332/340/432/420/425/ 432/440 with Centreware Internet Services

Verify that the Scan-to-File feature is installed on the Document Centre. Print a Configuration sheet and check the installed options list for Scan-to-File. If the Scan-to-File is not listed, contact your Xerox service representative to obtain and install the Scan-to-File kit. You can also call 1-800-ASK-XEROX for information about obtaining and installing this feature.

FlowPort Repository and Template Setup

The Xerox Document Centre uses templates and repositories to control the disposition of scanned documents. Information about these templates and repositories is stored inside the Document Centre and is accessible through the Web server embedded in the device. The Document Centre provides a default template, a number of named template (optional), a default public repository, and four other configurable public repositories.

Templates are shown as choices on the Document Centre Touch Screen. The default template is named @default.xst and it is the first template shown in the template list on the screen. The Xerox Document Centre uses templates and repositories to control the disposition of scanned documents. Information about these templates and repositories is stored inside the Document Centre and is accessible through the Web server embedded in the device. The Document Centre provides a default template, a number of named templates (optional), a default public repository, and four other configurable public repositories.

Templates are shown as choices on the Document Centre Touch Screen. The default template is named @default.xst and it is the first template shown in the template list on the screen.

Repositories are shown as choices for template setup in the Document Centre Web-based administration tool. Each repository has the following settings:

Repository List

Protocols

File Server IP Address

Directory Path

Login Name

Password

Xerox Document Centre Setup Guide for FlowPort 11

Configuring a Document Centre 220/230/332/340/432/420/425/432/440 with Centreware Internet Services

FlowPort Repository Setup

The following settings for the FlowPort Repository setup are recommended.

1 In your Web browsers Address (or Location) box, enter the TCP/IP address of your Document Centre.

2 Click on Properties.

3 Click on [+] Services.

4 Click on [+] Stored Templates

12 Xerox Document Centre Setup Guide for FlowPort

Configuring a Document Centre 220/230/332/340/432/420/425/432/440 with Centreware Internet Services

5 Click on Repository Setup.

6 Select an unused repository from the Repository List (Default is recommneded).

7 Verify that the protocol is TCP/IP.

8 Type the File Server IP address (the IP address of your FlowPort server).

9 Type the Directory Path /

10 Type the login name NSA, and the password nsa.

11 Click on Apply New Settings.

12 In the dialog box that appears, type the admin User Name and Password of the Document Centre, and click OK.

/

Xerox Document Centre Setup Guide for FlowPort 13

Configuring a Document Centre 220/230/332/340/432/420/425/432/440 with Centreware Internet Services

14 Xerox Document Centre Setup Guide for FlowPort

Configuring a Document Centre 220/230/332/340/432/420/425/432/440 with Centreware Internet Services

FlowPort Template Setup

1 Next, you need to set up the scan template that you will use when scanning to FlowPort server. Select Device Index.

Xerox Document Centre Setup Guide for FlowPort 15

Configuring a Document Centre 220/230/332/340/432/420/425/432/440 with Centreware Internet Services

2 Select Stored Templates.

16 Xerox Document Centre Setup Guide for FlowPort

Configuring a Document Centre 220/230/332/340/432/420/425/432/440 with Centreware Internet Services

3 Select [+] new.

4 In the Template fields, enter a name for the template in the Name field. Leave the Description and Owner fields blank.

5 Under Services, select File.

6 Click apply.

7 If you see the following dialog box, click Yes.

Xerox Document Centre Setup Guide for FlowPort 17

Configuring a Document Centre 220/230/332/340/432/420/425/432/440 with Centreware Internet Services

8 Click the browsers Refresh button. You should see the name of the new template in the list of Device Templates.

9 Click on [+] next to the name of the new template in the list of Device Templates.

List of Device

Templates

18 Xerox Document Centre Setup Guide for FlowPort

Configuring a Document Centre 220/230/332/340/432/420/425/432/440 with Centreware Internet Services

10 Click Scan and verify the scan settings. Typically, the default settings are used, however click Edit if you want to change them.

Text

Xerox Document Centre Setup Guide for FlowPort 19

Configuring a Document Centre 220/230/332/340/432/420/425/432/440 with Centreware Internet Services

11 Click File.

12 Under Stored templates, select the following: TCP/IP, Public, Default (or the repository designated for FlowPort), New Auto Generate, and TIFF (Multi-Page) . Then, click Apply New Settings.

13 The Document Center is now configured to scan to the FlowPort server.

20 Xerox Document Centre Setup Guide for FlowPort

Configuring a Document Centre 220/230/332/340/432/420/425/432/440 with Centreware Internet Services

Testing the FlowPort Template

To check that the Document Centre is ready for FlowPort use, perform the following test:

1 At the Document Centre, place a document in the scanner.

2 Select the FlowPort template and select Scan.

Note: If the Document Centre is properly configured, a DC confirmation sheet will be printed confirming that the scan to FlowPort was successful, otherwise an error report with some specific failure notice will be printed. If the

Manualsnet FAQs

If you want to find out how the Document Centre for FlowPort Xerox works, you can view and download the Xerox Document Centre for FlowPort Software Setup Guide on the Manualsnet website.

Yes, we have the Setup Guide for Xerox Document Centre for FlowPort as well as other Xerox manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Setup Guide should include all the details that are needed to use a Xerox Document Centre for FlowPort. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Xerox Document Centre for FlowPort Software Setup Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Xerox Document Centre for FlowPort Software Setup Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Xerox Document Centre for FlowPort Software Setup Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Xerox Document Centre for FlowPort Software Setup Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Xerox Document Centre for FlowPort Software Setup Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.