Xerox ColorQube 9303 Smart Card Installation Guide PDF

1 of 42
1 of 42

Summary of Content for Xerox ColorQube 9303 Smart Card Installation Guide PDF

Version 3.0 October 2014

Smart Card Installation and Configuration Guide (CAC/PIV/.Net/Access Client & Rijkspas)

Xerox WorkCentre 3655 Multifunction Printer

Xerox WorkCentre 5845/5855/5865/5875/5890 Multifunction Printer

Xerox WorkCentre 5945/5955 Multifunction Printer

Xerox WorkCentre 6655 Multifunction Printer

Xerox WorkCentre 7220/7225 Multifunction Printer

Xerox WorkCentre 7830/7835/7845/7855 Multifunction Printer

Xerox ColorQube 8700/8900 Multifunction Printer

Xerox ColorQube 9301/9302/9303 Multifunction Printer

2014 Xerox Corporation. All rights reserved. Xerox, Xerox and Design, ColorQube and WorkCentre are trademarks of Xerox Corporation in the United States and/or other countries. BR10996

Other company trademarks are also acknowledged.

Changes are periodically made to this document. Changes, technical inaccuracies, and typographic errors will be corrected in subsequent editions.

Document version 3.0: October 2014

Table of Contents

1 Introduction

Smart Card Feature Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Authentication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Hold All Jobs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 E-mail Signing and Encryption. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Supported Card Readers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Supported Card Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Minimum Software Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Documentation and Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

2 Preparation

Configuration Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

3 Installation

Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Connect the USB Smart Card Reader to the MFD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Software Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Enter the Smart Card Enablement Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Configuring the Smart Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Configure Smart Card Authentication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Enable NTP Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Configure Alternate Authentication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Configure a Security Certificate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Configure SSL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Configure Certificate Validation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Configure Smart Card Inactivity Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Configure Acquiring Logged-In Users E-mail Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Printing Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Configure Hold All Jobs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Configure Secure Print Driver Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Configure the Print Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Confirm the Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Using Smart Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

4 Troubleshooting

Fault Clearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Locating the Serial Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Troubleshooting Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 During Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 After Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Installation and Configuration Guide 3

Smart Card

Installation and Configuration Guide4

1Introduction

The Smart Card solution brings an advanced level of security to sensitive information. Organizations can restrict access to the walk-up features of a Xerox device. This ensures only authorized users are able to copy, scan, e-mail and fax information.

Once validated, a user is logged into the Xerox device for all walk-up features. The system allows for functions to be tracked for an added layer of security.

This guide explains how to install and configure the Smart Card solution. It identifies the resources and equipment required to complete a successful installation.

Should you require any further information, please contact your local Xerox Representative.

Installation and Configuration Guide 5

Introduction Smart Card

Smart Card Feature Overview Authentication

Xerox offers a feature called Smart Card authentication. This enables users who possess smart cards to use them for network authentication at the multifunction device (MFD). Smart cards contain the users Identity Certificate along with their public and private key. This enables the MFD to perform a Kerberos authentication to the Windows Active Domain Controller which originally issued the Identity Certificate.

The Smart Card feature was developed to support CAC smart cards and has been extended to support PIV, .NET, Access Client, Rijkspas, and other smart cards. This document describes the configuration settings for these smart cards.

The MFD will automatically determine which type of smart card type is inserted in the card reader and use the appropriate software libraries to communicate with the specific card. Authentication settings are configured on the MFD according to the network infrastructure.

Hold All Jobs

Xerox offers a feature called Hold All Jobs. This feature ensures all jobs are held securely at the MFD and are only available for release after a user has authenticated at the MFD. The MFD holds the jobs for a specified period of time and releases them only when the user releases them at the MFD. It is not necessary to enter a secure print PIN to use this feature.

To use Hold All Jobs, the print driver needs to be configured to either pull the users name (alias) from the smart card certificate or from the Windows Operating System. See the instructions in this document to configure the print driver.

This feature provides the following benefits:

Banner Pages are not required to separate jobs, which reduces waste.

Users can manage their held jobs more efficiently. Users can select only the jobs they want to print and delete older versions of documents that they no longer wish to print.

Confidential documents are held in the queue for the owner to release them, rather than waiting in the output tray to be picked up.

E-mail Signing and Encryption

With Smart Card authentication the MFD has full access to the users public and private keys and can use these keys for e-mail signing and encryption.

An e-mail payload can be signed via the smart card with the users private key. This enables other users to validate the signature with the users public key, which can be obtained from the user or from LDAP. This assures the recipient that the content is original and has not been tampered with in transit.

An e-mail payload can also be encrypted with the users public key via the smart card or LDAP, and then sent to the user. This offers the benefit that while in transit from the MFD through the e-mail infrastructure, no one can decipher the contents of the mail note. Once in the users inbox, the e-mail can be decrypted with the users private key, making the payload readable again.

Installation and Configuration Guide6

Smart Card Introduction

Supported Card Readers

The customer is responsible for providing a card reader for each Xerox device. The following card readers are compatible with the solution:

Gemplus GemPC USB SL

Gemplus GEMPC Twin

SCM Micro SCR3310

SCM Micro SCR3311

OmniKey Cardman 3021 USB

OmniKey Cardman 3121 USB

ActivCard USB Reader V2 with SCR-331 firmware1

Cherry ST1044U

Other CCID compliant readers may function with the solution, but have not been validated.

Supported Card Types

The customer is also responsible for purchasing and configuring the access cards. The following card types are supported:

CAC

PIV & PIV II

Gemalto.NET

Other card types may function with the solution, but have not been validated.

Installation and Configuration Guide 7

Introduction Smart Card

Minimum Software Levels

To identify the software level on your machine, press the Machine Status button on the Control Panel. The System Software Version number is displayed.

Documentation and Support

For information specifically about your Xerox product, the following resources are available:

System Administrator Guide provides detailed instructions and information about connecting your device to the network and installing optional features. This guide is intended for System/Machine Administrators.

User Guide provides detailed information about all the features and functions on the device. This guide is intended for general users.

Most answers to your questions will be provided by the support documentation supplied for your product. Alternatively you can contact the Xerox Support Center or access the Xerox website at www.xerox.com.

Product Minimum System Software Version CAC PIV .NET Access

Client Rijkspas

WorkCentre 3655 072.060.034.16800 Yes Yes Yes No No

WorkCentre 58xx 071.xxx.xxx.xxx.xxxxx Yes Yes Yes No No

WorkCentre 59xx 071.xxx.xxx.xxx.xxxxx Yes Yes Yes No No

WorkCentre 6655 072.060.034.16800 Yes Yes Yes No No

WorkCentre 72xx 072.110.044.20500 Yes Yes Yes No No

WorkCentre 78xx 071.xxx.xxx.xxx.xxxxx Yes Yes Yes No No

ColorQube 87xx/89xx 071.160.222.26601 Yes Yes Yes No No

ColorQube 93xx 071.xxx.xxx.xxx.xxxxx Yes Yes Yes No No

Installation and Configuration Guide8

2Preparation

This section explains the preparation and resources required to install the Smart Card feature.

Configuration Checklist

The following items are required to complete the installation:

Summary Status

1. Obtain the IP address or Host Name for each applicable Windows Domain Controller

2. If Domain controller certificate validation is required, obtain the DC certificate for each applicable controller including all intermediate certificates up to the root cert.

Note: This is typically only required for CAC

3. If Online Certificate Status Protocol (OCSP) is available, obtain the IP address or Host Name for the OCSP server

4. If a software upgrade is required obtain and install the required software release

5. Mount the smart card reader to the MFD and connect the USB cable to one of the rear ports. See Connect the USB Smart Card Reader to the MFD on page 12

6. Install the Smart Card software Feature Enablement Key. See Enter the Smart Card Enablement Key on page 18

7. Configure Smart Card Authentication, NTP (optional), and Alternate Login (optional). See Configuring the Smart Card on page 20

8. Install any required certificates and configure validation settings. See Configure a Security Certificate on page 22

9. Configure the MFD LDAP settings. See Configure Acquiring Logged-In Users E-mail Address on page 26

10. Configure the MFD SMTP (E-mail) and Signing/Encryption settings. See Configure SMTP (E-mail) Settings on page 27

11. Configure Hold All Jobs/Secure Print policy if required. See Printing Features on page 32

Installation and Configuration Guide 9

Preparation Smart Card

Installation and Configuration Guide10

3Installation

This section provides instructions for installing and configuring the Smart Card solution.

There are four main installation procedures to follow in sequence.

Hardware Installation

Unpacking the Smart Card Enablement kit and installing the card reader device.

Enabling the Smart Card

Use the Feature Enable Key to enable the Smart Card to be configured.

Configuring the Smart Card

Enabling the Smart Card function and customizing the settings.

Using Smart Card

Instructions on how to use the card reader device to access the device functions.

Installation and Configuration Guide 11

Installation Smart Card

Hardware Installation Connect the USB Smart Card Reader to the MFD

Install the card reader device using the following instructions.

1. Unpack the Smart Card Enablement Kit

The kit contains the following items:

- Smart Card Enablement Guide (1) - Four Dual Lock Fastener pads (Velcro) (2) - Three Cable Ties (3) - One Ferrite Bead (4) Ensure you have read the licence agreement and agree to the terms and conditions specified prior to installation.

Installation and Configuration Guide12

Smart Card Installation

2. Locate the card reader device being installed

- There are four types of card reader available, one upright model or three slimline models. - Locate the device being installed and ensure it has been configured.

Note: The System Administrator should configure the cards prior to the card reader being installed on the machine.

Installation and Configuration Guide 13

Installation Smart Card

3. Attach the ferrite bead to the reader cable.

Note: The ferrite bead should be clipped onto the cable directly behind the connector.

Installation and Configuration Guide14

Smart Card Installation

4. Attach the fasteners to the card reader device

- Fasteners have been provided to secure the card reader to the Xerox device. - Peel back the fastener backing strip. - Position the fastener on the under-side of the card reader, as shown. - Repeat for each of the fasteners supplied.

Installation and Configuration Guide 15

Installation Smart Card

5. Remove the fastener backing strips

When all the fasteners have been attached to the card reader, remove the backing strips on each of the fasteners.

Installation and Configuration Guide16

Smart Card Installation

6. Place the card reader on the Xerox device

- Gently place the card reader on the device (do not fix in place at this point). - Position the card reader in a suitable location, ensure it does not obstruct any access points or the

opening of doors or covers. - Check the cable has sufficient length to connect to the rear of the network controller. - Once it is in a suitable location, press firmly on the card reader to fix it in place.

7. Connect the card reader to the Xerox device

- Insert the USB connection into the slot provided on the rear of the network controller. - Use the cable ties provided to ensure the cabling is neat and tidy.

The hardware installation is now complete.

Installation and Configuration Guide 17

Installation Smart Card

Software Configuration Enter the Smart Card Enablement Key

Before you configure the Smart Card solution, you need to enable the Smart Card feature on your Xerox device using Internet Services. The Feature Enablement Key is printed on the inside cover of the Enablement guide provided within the Smart Card kit.

Follow the instructions below to enable the device software.

1. Access Internet Services

a. Open the web browser from your Workstation. b. In the URL field, enter http:// followed

by the IP Address of the device. For example: If the IP Address is 192.168.100.100, enter the following into the URL field: http://192.168.100.100.

c. Press Enter to view the Home page.

2. Access Properties

a. Select the Properties tab. b. If prompted, enter the Administrator

User ID and Password. The default is admin and 1111.

c. Select the Login button.

3. Enable the Smart Card software

a. Select the Properties link. b. Select the

Login/Permissions/Accounting link. c. Select the Login Methods link. d. Select the Touch UI Method button.

Installation and Configuration Guide18

Smart Card Installation

e. From the Touch UI Method drop- down menu, select Smart Cards.

f. If you require users to have an alternative method of authentication, select User Name/Password from the Alternate Touch UI Method drop-down menu.

g. If you require the device to use the E- mail address registered to the authenticated user, select the Personalize Touch UI checkbox

h. Select Save.

i. In the Smart Card Enablement area, enter the unique Feature Enablement Key provided on the inside cover of the Smart Card Enablement Guide.

j. Select Next.

A confirmation message is displayed.

k. Select Next. The Smart Card settings are now ready for configuring.

Note: No services will be restricted until Smart Card has been fully configured using Internet Services.

Installation and Configuration Guide 19

Installation Smart Card

Configuring the Smart Card Once the Smart Card feature has been enabled on the device it can be configured using Internet Services.

Configure Smart Card Authentication

Follow the instructions below to enable and configure the Smart Card:

1. In the Internet Services Login/Permissions/Accounting menu, ensure you have the Login Methods link selected.

2. Enter the Domain Controller details for the authentication server.

a. Select Domain Controller(s) - Edit from the Configuration Settings list.

Note: Initially the Domain Controller(s) will be empty and the NTP server will not be set.

b. Select Add Domain Controller.

c. Select Windows Based Domain Controller or leave this box unchecked to select Linux Based Domain Controller.

d. Select either IP Address or Host Name and enter the Domain Controller details. If you enter the Host Name, this must be the fully qualified Host Name.

e. Ensure Port 88 is selected unless your Kerberos Port is different. f. Enter the Domain (this must be the fully qualified Domain Name). g. Select Save.

Installation and Configuration Guide20

Smart Card Installation

Enable NTP Service

3. Configure the Date & Time to update automatically

a. Select the Network Time Protocol - Edit link.

b. Select the Enabled box to enable NTP.

c. Enter the IP address or Host Name of the Primary and Alternate Time Server. Often this can be the same address as the Domain Controller.

d. Select Save.

e. View the summary screen and ensure all settings are correct.

f. Select Close.

Installation and Configuration Guide 21

Installation Smart Card

Configure Alternate Authentication

If Alternate Authentication is not required, go to Configure a Security Certificate on page 22.

4. If Alternate Authentication is enabled, select the Authentication Servers / Touch UI (Alternate) - Edit link in the Configuration Settings list to configure the server.

a. Select the Authentication Type from the drop-down menu.

b. Select Add New.

c. Enter the required Domain or Realm. d. Select either IP Address or Host

Name and enter the server details. For most installations the Alternate Authentication server will be the same as the Smart Card Domain Controller.

e. Select Save. f. Select Close.

Configure a Security Certificate

If you require the MFD to be configured for certificate validation, complete this section. The following instructions are included:

Create a Device Certificate on page 23

Import a Certificate Authority Certificate on page 23

Install a Domain Controller Certificate on page 24

If certificate validation is not required, go to section Configure Smart Card Inactivity Timer on page 26.

Installation and Configuration Guide22

Smart Card Installation

Create a Device Certificate

The device automatically creates a self-signed certificate. Complete this section if you want to create a new device certificate.

5. To create a new device certificate:

a. In the Properties tab select the Security link.

b. Select Certificates > Security Certificates.

c. Select the Xerox Device Certificate tab.

d. Select Create New Xerox Device Certificate.

e. Complete the Self Signed Certificate fields.

f. Select Finish. g. Proceed to Configure SSL on page 24.

Import a Certificate Authority Certificate

6. Complete these steps if you want to import a certificate from a Certificate Authority:

a. In the Properties tab select the Security link. b. Select Certificates > Security

Certificates. c. Select the Root/Intermediate

Trusted Certificate(s) tab. d. Click Install external

Root/Intermediate trusted certificates.

e. Click the Browse button and navigate to the location of your Certificate Authority certificates.

f. Click Next. g. If the certificate is encrypted, enter

the password at the Password Required screen. h. Click Next.

Note: Both RootCA and Intermediate CA certificates need to be imported to the MFD to establish a Chain of Trust for the certificates located on the operators smart card.

i. Proceed to Configure SSL on page 24

Installation and Configuration Guide 23

Installation Smart Card

Install a Domain Controller Certificate

7. Complete these steps if you want to install a domain controller certificate.

a. In the Properties tab select the Security link.

b. Select Certificates > Security Certificates.

c. Select the Domain Controller Certificates tab.

d. Click Install Domain Controller Certificate.

e. Click the Browse button and navigate to the location of your Domain Controller certificates.

f. Click Next. g. Continue until all required certificates have been uploaded.

Configure SSL

8. SSL is used to provide a secure connection between your computer and the MFD when security certificates are configured on the MFD. SSL is automatically enabled on the device. If you do not want to configure SSL, proceed to Configure Certificate Validation on page 25.

a. In the Properties tab select the Connectivity link. b. Select Setup. c. In the Protocol list, select HTTP -

Edit. d. If you want to Force Traffic over SSL,

select Yes (All HTTP requests will be switched to HTTPS).

e. Select the required certificate from the Choose Device Certificate drop- down menu.

f. If you have changes to apply, select Save and the device will reboot automatically. If you have not made any changes, select Cancel.

Installation and Configuration Guide24

Smart Card Installation

Configure Certificate Validation

9. If you do not require certificate validation proceed to Configure Smart Card Inactivity Timer on page 26.

a. In the Properties tab, select the Login/Permissions/Accounting link.

b. Select Login Methods. c. Select Certificate Validation - Edit

in the Configuration Settings menu.

d. Select the required Validation Options.

e. If you have selected one or more option, click Next to configure further settings.

f. If prompted, enter the OCSP Server URL to be used for certificate validation.

g. If prompted, select Proxy Server - Configure to enter the proxy server information. If the OCSP server is outside the firewall, a proxy server may be required to access the server.

h. Select the Domain Controller Certificate(s) to be used to validate each domain controller. i. Click Save.

Installation and Configuration Guide 25

Installation Smart Card

Configure Smart Card Inactivity Timer

10. If you do not require inactivity timeout settings for Smart Card authentication, proceed to Configure Acquiring Logged-In Users E-mail Address on page 26.

a. In the Properties tab, select the Login/Permissions/Accounting link.

b. Select Login Methods. c. Select Smart Card Inactivity Timer

- Edit.

d. Enter the required number of minutes for Timer.

e. Click Save.

Configure Acquiring Logged-In Users E-mail Address

11. This section requires you to configure LDAP and SMTP server information. If you do not want to configure Acquiring Logged-In Users E-mail Address settings, proceed to Confirm the Installation on page 34.

a. In the Properties tab, select the Login/Permissions/Accounting link.

b. Select Login Methods. c. Select Acquiring Logged In Users

Address - Edit.

d. Select the required option for Acquire logged in users e-mail address.

e. If you select Auto or Only Network Address Book (LDAP), click Network Address Book (LDAP) - Edit to configure LDAP server settings.

f. Click Add New.

Installation and Configuration Guide26

Smart Card Installation

g. At the LDAP Server screen, enter a Friendly Name.

h. Enter the IP address or Host Name of the Primary and Alternate LDAP server.

i. Select the required LDAP Server from the drop-down list.

j. Enter the LDAP Search Directory Root. This is typically related to the servers domain name. For example, if the servers Fully Qualified Domain Name is Hostname.Example.Search.Root, the search directory root is dc=Example,dc=Search,dc=Root.

k. Enter the required Login Credentials to Access LDAP Server. l. Click Apply. m. Click Close.

n. Select LDAP Policies.

o. Select Enable SASL Binds to LDAP.

Note: Smart cards use a ticket based authentication to LDAP and require SASL for authentication.

p. Click Save. q. Click Close.

Configure SMTP (E-mail) Settings

12. In the E-mail Setup screen, select the Required Settings tab.

a. Select SMTP - Edit.

Installation and Configuration Guide 27

Installation Smart Card

b. Select Use DNS (to identify SMTP Server) to configure the server address using DNS, or select IP Address or Host Name and enter the SMTP server address.

c. Enter the required Device E-mail Address.

d. Select Save.

Configure SMTP Authentication

13. Select SMTP - Edit.

a. Select the SMTP Authentication tab.

b. For the required method of authentication for SMTP Login credentials applied to e-mail jobs sent from the machines touch interface select Logged-in User.

Note: The Logged-in users credentials are typically used to provide authentication for the SMTP server when Smart Card authentication is enabled.

c. Select Always Use Kerberos Tickets. d. Select None for automated emails. e. Select Save.

Configure Connection Encryption

14. Select SMTP - Edit.

a. Select the Connection Encryption tab.

b. Select the required encryption setting.

c. Select Save.

Configure File Size Management

15. Select SMTP - Edit.

a. Select the File Size Management tab.

Note: This screen defines how large email payloads are managed.

b. Select the required settings. c. Select Save

Installation and Configuration Guide28

Smart Card Installation

Test Configuration

16. Select SMTP - Edit.

a. Select the Test Configuration tab.

Note: This screen allows you to send a test e-mail to confirm that all e-mail settings are correct.

b. Enter a valid e-mail address in the To Address field. c. Select Send E-mail.

Note: If the SMTP settings are correct, the screen will display a success message and an e-mail will be received at the address

d. Select the Required Information tab.

e. Required Settings Configured displays to confirm required settings are configured.

f. Select Save.

Configure General E-mail Settings

17. In the E-mail Setup screen, select the General tab.

a. Enter the required information to display in the Subject of an e-mail sent from the MFD.

b. Select the required information to display in the Message Body.

c. Enter the information to be included in the Signature.

d. Select the required option for printing a Confirmation Sheet from the drop-down menu. e. Select Enabled for Auto Add Me if you want the MFD to automatically add the logged-in users e-mail

address to the To: field. f. Select Enabled for Only Send to Self if you want the MFD to only send e-mails to the user who is logged

in at the MFD. g. Select Apply.

Installation and Configuration Guide 29

Installation Smart Card

Configure Address Books

18. Select the Address Books tab.

a. LDAP was configured in a previous step. If you require the Device Address Book, select the Device Address Book - Edit link.

b. Configure the Device Address Book. Instructions are available in the System Administration Guide.

Configure E-mail Defaults

19. Select the Defaults tab.

a. Select the required options for e-mail default settings.

b. Save your changes.

Configure E-mail Compression

20. Select the Compression tab.

a. Select the required Compression Settings.

b. Click Apply.

Configure E-mail Security

21. Select the Security tab.

a. Select Encryption/Signing - Edit.

b. Select the required Encryption Enablement setting; Off -E-mail cannot be signed Always On - E-mail must be

signed Editable by user - E-mail can be

sent signed or unsigned according to local user settings.

c. If you selected Editable by User, select On for E-mail Encryption Default if you require signing to be on by default.

d. Select the required Encryption Algorithm. e. Select Apply.

Installation and Configuration Guide30

Smart Card Installation

22. If you want to configure e-mail domain restrictions, click Edit in the Network Policies area.

a. Select the required restrictions. Domain Filtering enables you

to configure a list of domains to allow or block e-mails.

E-mail Filtering allows you to send internal e-mail without the need to add @ corporate name. This option requires your e-mail server to be configured to allow this.

b. Select Save.

23. If you want to configure restrictions on email recipients, click Edit in the User Policies area.

a. Select the required settings for User Permissions.

b. Save your changes. c. If required, click Edit in the Only

Send to Self area. d. Select the required settings for User

Policies. e. Save your changes.

The Smart Card settings are now configured.

Installation and Configuration Guide 31

Installation Smart Card

Printing Features The Hold All Jobs and Secure Print features can be configured to ensure jobs are held securely at the MFD until the user authenticates at the Control Panel.

Configure Hold All Jobs

Hold all Jobs allows you to configure the MFD to require users to release print jobs manually at the Control Panel. If you want to configure Hold all Jobs, follow these instructions.

1. Access Internet Services and select Properties. Refer to Access Internet Services on page 18 for instructions.

a. Select Services > Printing > Hold All Jobs.

b. Select the required Enablement option: Hold Jobs in a Private Queue:

the MFD holds jobs in a locked folder. Users must log in at the Control Panel to view, print and delete jobs.

Hold Jobs in a Public Queue: the MFD holds sent jobs in an unlocked folder. Users are not required to log in at the Control Panel.

c. Select the required option for Unidentified Job Policies (User ID Unknown). Further details are available in the System Administrator Guide.

Installation and Configuration Guide32

Smart Card Installation

Configure Secure Print Driver Defaults

The Secure Print feature allows you to send a job to the MFD with a unique passcode. Jobs are stored at the MFD until the user enters the same passcode to release them. Further information about how to use Secure Print is available in your User Guide. You can configure the Secure Print Driver Default settings to require the user to enter a User ID to release secure print jobs at the Control Panel, instead of a passcode. If you want to configure Secure Print Driver Defaults, follow these instructions.

1. Access Internet Services and select Properties. Refer to Access Internet Services on page 18 for instructions.

a. Select Services > Printing > Secure Print.

b. Select the Print Driver Defaults tab. c. Select the required Method:

Passcode: requires users to type a passcode to release their Secure Print jobs at the Control Panel. If required, enter a number from 4-10 to specify the length of the Secure Print Passcode.

User ID: requires users to log in at the Control Panel to release their Secure Print jobs. d. Click Apply.

Further information on how to configure Secure Print Settings is available in the System Administrator Guide.

Configure the Print Driver

Your print driver can be configured to pull the users name (alias) from the smart card certificate, or from the Windows Operating System. To configure the print driver to pull the users name from the smart card certificate follow these instructions.

1. Install your Xerox Print Driver. Instructions are available in the System Administrator Guide.

a. Access Properties for your print driver. b. Select the Administration tab. c. Select Enabled from the Access and

Verification drop-down menu. d. Select OK.

Note: If Hold All Jobs or Secure Print Driver Defaults are configured at the MFD, they may override the settings configured in your print driver. Refer to Configure Hold All Jobs on page 32 and Configure Secure Print Driver Defaults on page 33.

Installation and Configuration Guide 33

Installation Smart Card

Confirm the Installation When the card reader and the software has been installed and configured, the Card Reader Detected screen displays on the Xerox device local user interface.

Smart Card is now ready for use.

Note: If the card reader is not detected, refer to Troubleshooting Tips on page 39 for information.

Installation and Configuration Guide34

Smart Card Installation

Using Smart Card Once the Smart Card has been enabled, each user must insert a valid card and enter their Personal Identification Number (PIN) on the touch screen. When a user has finished using the Xerox device, they are then required to remove their card from the card reader to end the session. For instances where a user forgets to remove their card, the machine will end the session automatically after a specified period of inactivity.

Follow the instructions below to use the Smart Card:

1. The Authentication Required window may be displayed on the touch screen, depending on your device configuration.

2. Insert your card into the card reader.

3. Use the touch screen and numeric keypad to enter your PIN and then select Enter.

4. If the card and PIN are authenticated, access is granted.

Note: If the access attempt fails, refer to Troubleshooting Tips on page 39.

5. Complete the job.

6. To end the session, remove your card from the card reader.

The current session is terminated and the Authentication Required window is displayed.

Installation and Configuration Guide 35

Installation Smart Card

Installation and Configuration Guide36

4Troubleshooting

For optimal performance from your card reader, ensure the following guidelines are followed:

The Card Reader is only compatible with network connected products.

Ensure the Card Reader is plugged into the Network Controller. Refer to Connect the card reader to the Xerox device on page 17 for instructions.

Do not position the Card Reader in direct sunlight or near a heat source such as a radiator.

Ensure the Card Reader does not get contaminated with dust and debris.

Installation and Configuration Guide 37

Troubleshooting Smart Card

Fault Clearance When a fault occurs, a message displays on the User Interface which provides information relating to the fault. If a fault cannot be resolved by following the instructions provided, refer to Troubleshooting Tips on page 39.

If the problem persists, identify whether it is related to the card reader device or the Xerox device.

For problems with the card reader device, contact the manufacturer for further assistance.

For problems relating to the Xerox device, contact the Xerox Welcome and Support Center. The Welcome and Support Center will want to know the nature of the problem, the Machine Serial number, the fault code (if any) plus the name and location of your company.

Contact Xerox using the numbers 1-800-ASK-XEROX or 1-800-275-9376.

Locating the Serial Number Press the Machine Status button on the Control Panel.

The Machine Information tab is displayed. The Machine Serial Number is displayed on this screen.

Note: The serial number can also be found on a metal plate inside the front door.

Installation and Configuration Guide38

Smart Card Troubleshooting

Troubleshooting Tips The table below provides a list of problems and the possible cause and a recommended solution.

If you experience a problem during the installation process please refer to the During Installation problem solving table below.

If you have successfully installed the Smart Card solution but are now experiencing problems, refer to After Installation on page 40.

During Installation

Problem Possible Cause Solution

Card reader is installed but no message displays on the User Interface

Card reader is faulty. Try a different card reader. Contact the System Administrator.

Card reader connection is faulty. Check the cable is plugged in correctly. Refer to Connect the card reader to the Xerox device on page 17 for instructions.

Unplug the card reader cable then plug back in.

Plug the card reader into a different USB port.

Card reader is not compatible. Check that the card reader is on the list of compatible devices, refer to Supported Card Readers on page 7.

Smart Card access is not enabled on the machine.

Enable Smart Card through the Properties set up screens using Internet Services, refer to Software Configuration on page 18.

Installation and Configuration Guide 39

Troubleshooting Smart Card

After Installation

Problem Possible Cause Solution

The login was successful, however you do not have the appropriate access to the operation you requested

LDAP not configured properly or local user permission roles not configured properly.

Check the authorization method.

The passcode entered was incorrect Incorrect PIN has been entered. Caution: Consecutive incorrect entries may lead to your card being locked.

Carefully re-enter the PIN.

Authentication failed. There is a problem with your card that is preventing successful login

Certificates cannot be read from the card.

Contact the Registration Authority to reload the certificates or get a new card.

Authentication failed because the device was unable to access the remote server (Domain Controller) or the authentication sequence failed

Domain Controller IP Address or Host Name is incorrect.

Verify the server address is entered correctly.

Incorrect Domain. Verify the Domain has been properly configured.

Network error Check the network cable is firmly connected.

The number of attempts have been exceeded

Card has been locked due to failed login attempts.

Contact the Registration Authority to reset the PIN or to get a new card.

Server Certificate Failed Authentication failed because the remote server (Domain Controller) certificate could not be found, is invalid, has expired or been revoked

This is usually because the device does not trust the certificates on the Smart Card.

Ensure all the chain of trust certificates are imported on the device.

Check the Operators CAC to see which Root CA and Intermediate CA issued the CAC certificates.

Card reader not detected The card reader has been disconnected.

Verify that the card reader is properly connected.

If you suspect the reader has failed, swap with a known working reader.

Installation and Configuration Guide40

Smart Card Troubleshooting

Invalid Timestamp. Authentication failed due to a time or date difference between the device and the remote server (Domain Controller)

NTP not enabled or properly configured.

Verify that Network Time Protocol is correctly set up, refer to Enable NTP Service on page 21.

GMT offset is not set correctly. If you are not using DHCP, verify the date and time and GMT Offset (Time Zone) is correct. Instructions are available in the System Administrator Guide.

Verify that GMT offset is correct for Daylight Savings Time.

Unforeseen errors are mapped to this error message.

Cannot see the Internet Services web page

IP Address incorrect or has been reset. Check the IP Address printed on the configuration report. Ensure the DHCP settings match your site settings.

To print a configuration report at the Xerox device, select Machine Status, then Information Pages. Select the Configuration Report from the list and select Print.

Problem Possible Cause Solution

Installation and Configuration Guide 41

Troubleshooting Smart Card

Installation and Configuration Guide42

Manualsnet FAQs

If you want to find out how the ColorQube 9303 Xerox works, you can view and download the Xerox ColorQube 9303 Smart Card Installation Guide on the Manualsnet website.

Yes, we have the Installation Guide for Xerox ColorQube 9303 as well as other Xerox manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Installation Guide should include all the details that are needed to use a Xerox ColorQube 9303. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Xerox ColorQube 9303 Smart Card Installation Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Xerox ColorQube 9303 Smart Card Installation Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Xerox ColorQube 9303 Smart Card Installation Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Xerox ColorQube 9303 Smart Card Installation Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Xerox ColorQube 9303 Smart Card Installation Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.