Contents

Xerox 6050A Scanner User Guide PDF

1 of 176
1 of 176

Summary of Content for Xerox 6050A Scanner User Guide PDF

October 2008 701P48934

6030 / 6050 / 6050A / 510 Series / 721P / 6204 / 6279

Wide Format Copy System

User Guide

Xerox Corporation

Global Knowledge and Language Services

800 Phillips Road 218-01A

Webster, New York 14580

2008 by Xerox Corporation. All rights reserved.

Copyright protection claimed includes all forms and matters of copyrightable material and information now allowed by statutory judicial law or hereinafter granted, including without limitation, material generated from the software programs which are displayed on the screen such as icons, screen displays, looks, etc.

Printed in the United States of America.

XEROX and all Xerox product names mentioned in this publication are trademarks of XEROX CORPORATION.

One or more of the fonts listed within this document may be a registered trademark of Morisawa & Company, Ltd. or DYNALAB, Inc.

Changes are periodically made to this document. Changes, technical inaccuracies, and typographic errors will be corrected in subsequent editions.

Wide Format Copy System User Guide i

Table of Contents 1 SAFETY NOTES......................................................................................................................................................1

WARNING ELECTRICAL SAFETY INFORMATION....................................................................................................2 OPERATIONAL SAFETY INFORMATION........................................................................................................................3 MAINTENANCE INFORMATION....................................................................................................................................4 OZONE SAFETY INFORMATION ...................................................................................................................................4 FOR CONSUMABLES ...................................................................................................................................................4 RADIO FREQUENCY EMISSIONS ..................................................................................................................................4

United States, Canada, Europe, Australia/New Zealand: .....................................................................................4 PRODUCT SAFETY CERTIFICATION .............................................................................................................................5 REGULATORY INFORMATION......................................................................................................................................5

2 GETTING TO KNOW THE WIDE FORMAT COPY SYSTEM .......................................................................7 FEATURE KEYS...........................................................................................................................................................8 SCAN SYSTEM STANDARD COMPONENTS .................................................................................................................10 SCAN SYSTEM COMPACT COMPONENTS...................................................................................................................13 SCAN SYSTEM CONTROL PANEL...............................................................................................................................14

Option Keys .........................................................................................................................................................15 Image Quality Area .............................................................................................................................................19 Reduce/Enlarge ...................................................................................................................................................24 Graphical Display and Navigation Keys .............................................................................................................26 Numeric Keypad and Special Features/Control Keys .........................................................................................28 Special Features Keys..........................................................................................................................................29 Scan Control Keys ...............................................................................................................................................29

THE PRINTER AND THE FREEFLOW ACCXES CONTROLLER.......................................................................................30 POWERING ON THE WIDE FORMAT COPY SYSTEM ...................................................................................................30

Initial Power-On..................................................................................................................................................30 Switching on the Scan System..............................................................................................................................31 Switching on the PUN, YKE or LVX Controller and the Printer (Xerox Wide Format 510 Series/721P)...........31 Switching on the Printer and the Controller (PUN, YKE, YKE-N, FRX, and LVX controllers)..........................33

POWERING THE XEROX 6204 WIDE FORMAT SOLUTION ON/OFF.............................................................................37 Powering On the System......................................................................................................................................37 Powering Off the System......................................................................................................................................37

POWERING THE XEROX 6279 WIDE FORMAT SOLUTION ON/OFF.............................................................................38 Powering On the System......................................................................................................................................38 Powering Off the System......................................................................................................................................39 Scan System Warm-up .........................................................................................................................................40 Powering off the System.......................................................................................................................................40

3 DOCUMENT QUALITY.......................................................................................................................................41 DOCUMENT QUALITY ...............................................................................................................................................41 DYNAMIC BACKGROUND REMOVAL ........................................................................................................................41 AUTOMATIC EDGE DETECTION AND DOCUMENT CENTERING ..................................................................................42 DETERMINING DOCUMENT QUALITY........................................................................................................................42

What is a good quality document?.......................................................................................................................43

Table of Contents

ii Wide Format Copy System User Guide

What is a bad quality document?.........................................................................................................................43 PREPARING DOCUMENTS ..........................................................................................................................................44 SCANNING STRATEGIES ............................................................................................................................................45

4 IMAGE QUALITY.................................................................................................................................................47 ORIGINAL, TYPE.......................................................................................................................................................48 COPY MODE..........................................................................................................................................................48

Type, Normal, Line, and Photo............................................................................................................................48 SCAN MODE..........................................................................................................................................................49

Type and Normal .................................................................................................................................................49 Type Line .............................................................................................................................................................50 Type Photo...........................................................................................................................................................51 Type, Color ..........................................................................................................................................................52

BACKGROUND SUPPRESSION ....................................................................................................................................54 COPY ........................................................................................................................................................................55

5 MAKING COPIES.................................................................................................................................................57 MAKING COPIES .......................................................................................................................................................57

Controlling the scan ............................................................................................................................................57 Image Quality ......................................................................................................................................................58

MAKING A COPY WITH THE DEFAULT SETTINGS........................................................................................................59 MAKING A COPY THE SAME SIZE AS THE ORIGINAL DOCUMENT ................................................................................60 FITTING THE IMAGE TO A FIXED COPY SIZE ...............................................................................................................61

6 SCANNING WHEN USING A FOLDER ............................................................................................................63 SCANNING WHEN USING A FOLDER...........................................................................................................................63

Ready to Copy Finisher Screen ...........................................................................................................................64 7 SCANNING OVERSIZED DOCUMENTS..........................................................................................................65

SCANNING OVERSIZED DOCUMENTS ........................................................................................................................65 LONG DOCUMENTS...................................................................................................................................................65 WIDE DOCUMENTS...................................................................................................................................................65

8 SPECIAL FEATURES KEYS...............................................................................................................................67 SPECIAL FEATURES KEYS..........................................................................................................................................67 PRINTER INTERRUPT KEY.........................................................................................................................................68 STORE/RECALL KEY.................................................................................................................................................69

Last Job ...............................................................................................................................................................69 Recalling the Last Job .........................................................................................................................................70 Reprinting with Changed Features......................................................................................................................70 Deleting the Last Job ...........................................................................................................................................71 Job Templates ......................................................................................................................................................71 Saving Job Templates ..........................................................................................................................................72 Recalling Job Templates......................................................................................................................................73 Deleting Job Templates .......................................................................................................................................74 Save Default Template.........................................................................................................................................74 Recall Factory Defaults.......................................................................................................................................75

FINISHER KEY...........................................................................................................................................................75 Finisher menu options .........................................................................................................................................77

SETS BUILD KEY ......................................................................................................................................................80 Preparing to Build the Set ...................................................................................................................................80 Building and Printing the Set...............................................................................................................................80

BATCH KEY..............................................................................................................................................................82 TRANSFORM KEY .....................................................................................................................................................83

Margins................................................................................................................................................................83 Justification .........................................................................................................................................................85

Table of Contents

Wide Format Copy System User Guide iii

Transform ............................................................................................................................................................86 SAMPLE KEY.............................................................................................................................................................88

Copy Mode Sample..............................................................................................................................................88 Scan Mode Sample...............................................................................................................................................89

9 SCANNING TO THE NETWORK (SCAN MODE)...........................................................................................91 SCANNING TO THE NETWORK (SCAN MODE)...........................................................................................................91 SWITCHING BETWEEN COPY MODE AND SCAN MODE ............................................................................................92 UNDERSTANDING THE READY TO SCAN SCREEN .................................................................................................93 SELECTIONS DISABLED IN SCAN MODE ...................................................................................................................93 OPERATING IN SCAN MODE.....................................................................................................................................94 CLEARING THE SCANNED IMAGES.............................................................................................................................95 MANAGING THE FILE SYSTEM ..................................................................................................................................96 SCANNING MULTIPLE PAGES TO MAKE A FILE.........................................................................................................96

10 MAIN MENU........................................................................................................................................................99 MAIN MENU .............................................................................................................................................................99 CONFIGURATION MENU .........................................................................................................................................100

Localization .......................................................................................................................................................101 Control Panel ....................................................................................................................................................101 Copy Options .....................................................................................................................................................102 Image Enhancements .........................................................................................................................................107 Timers ................................................................................................................................................................108 Power Saver.......................................................................................................................................................109 Scanner Control.................................................................................................................................................110

SYSTEM INFORMATION MENU................................................................................................................................112 System Description ............................................................................................................................................112 Recent Fault List................................................................................................................................................114 Configuration Prints..........................................................................................................................................115

SYSTEM ADMINISTRATION MENU ..........................................................................................................................117 Entering the System Administration Password..................................................................................................117 Job accounting...................................................................................................................................................118 File System.........................................................................................................................................................118 Change Password ..............................................................................................................................................122 Security Settings ................................................................................................................................................123

DIAGNOSTICS MENU ...............................................................................................................................................124 Usage Meters.....................................................................................................................................................125 Clear Scanner Usage.........................................................................................................................................125 Scanner Diagnostics ..........................................................................................................................................125 Password ...........................................................................................................................................................139

11 JOB ACCOUNTING..........................................................................................................................................141 JOB ACCOUNTING...................................................................................................................................................141 OVERVIEW .............................................................................................................................................................141 JOB ACCOUNTING MODE MENU .............................................................................................................................142 SUBMITTING JOBS ..................................................................................................................................................142

Over the Network...............................................................................................................................................143 Terminating Use Under an Account ..................................................................................................................144

12 CLEANING AND MAINTENANCE - SCAN SYSTEM ................................................................................145 CLEANING AND MAINTENANCE - SCAN SYSTEM.....................................................................................................145 CLEANING THE PLATEN GLASS, DOCUMENT DRIVE ROLLS, AND BACKER ROLL ...................................................146 CLEANING THE CALIBRATION STRIP.......................................................................................................................147

13 PROBLEM SOLVING.......................................................................................................................................149 PROBLEM SOLVING ................................................................................................................................................149

Table of Contents

iv Wide Format Copy System User Guide

Problem Solving Table ......................................................................................................................................149 Error Code Messages Table ..............................................................................................................................153

14 SPECIFICATIONS ............................................................................................................................................155 SPECIFICATIONS .....................................................................................................................................................155

15 APPENDICES.....................................................................................................................................................157 APPENDIX 1: SCANNING RESOLUTIONS AND SPEEDS..............................................................................................157 APPENDIX 2: PAPER SHEET SIZES...........................................................................................................................158 APPENDIX 3: PAPER ROLL SIZES ............................................................................................................................159 APPENDIX 4: LED STATUS INDICATORS ................................................................................................................160 APPENDIX 5: MAIN MENU STRUCTURE .................................................................................................................161

16 INDEX .................................................................................................................................................................163

Wide Format Copy System User Guide 1

1 Safety Notes

Read these safety notes carefully before using this product to ensure that you operate the equipment safely.

Your Xerox/Fuji Xerox product and recommended supplies have been designed and tested to meet strict safety requirements. These include safety agency approval, and compliance with established environmental standards. Please read the following instructions carefully before operating the product and refer to them as needed to ensure the continued safe operation of your product.

The safety and environment testing and performance of this product have been verified using Xerox materials only.

WARNING: Any unauthorized alteration, which may include the addition of new functions or connection of external devices, may affect the product certification. Please contact your Authorized Local Dealer for more information.

Warning Markings

All warning instructions marked on or supplied with the product should be followed.

Warning This WARNING alerts users to areas of the product where there is the possibility of personal injury

Warning This WARNING alerts users to areas of the product where there

are heated surfaces, which should not be touched.

Electrical Supply This product shall be operated from the type of electrical supply indicated on the product's data plate label. If you are not sure that your electrical supply meets the requirements, please consult your local power company for advice.

1 Safety Notes

2 Wide Format Copy System User Guide

WARNING: This product must be connected to a protective grounded circuit. This product is supplied with a plug that has a protective grounding pin. This plug will only fit into a grounded electrical outlet. This is a safety feature. To avoid risk of electric shock, contact your electrician to replace the electrical outlet if you are unable to insert the plug into it. Never use a grounding adapter plug to connect the product to an electrical outlet that lacks a grounded connection terminal. Operator Accessible Areas This equipment has been designed to restrict operator access to safe areas only. Operator access to hazardous areas is restricted with covers or guards, which would require a tool to remove. Never remove these covers or guards.

Maintenance Any operator product maintenance procedures will be described in the user documentation supplied with the product. Do not to carry out any maintenance on this product that is not described in the customer documentation.

Cleaning Your Product Before cleaning this product, unplug the product from the electrical outlet. Always use materials specifically designated for this product, as the use of other materials may result in poor performance and may create a hazardous situation. Do not use aerosol cleaners, because they may be explosive and flammable under certain circumstances.

WARNING Electrical Safety Information Use only the power cord supplied with this equipment.

Plug the power cord directly into a grounded electrical outlet. Do not use an extension cord. If you do not know if an outlet is grounded, consult a qualified electrician.

If this machine needs to be moved to a different location, contact a Xerox service representative or your authorized local representative or service support organization.

Improper connection of the equipment-grounding conductor can result in electrical shock. Do not place this equipment where people might step or trip on the power cord.

Do not place objects on the power cord.

Do not override or disable electrical or mechanical interlocks.

Do not obstruct the ventilation openings.

Never push objects of any kind into slots or openings on this equipment.

If any of the following conditions occur, switch off the power to the machine immediately and disconnect the power cord from the electrical outlet. Call an authorized local service representative to correct the problem. - The equipment emits an unusual noise or odor. - The power cord is damaged or frayed. - A wall panel circuit breaker, fuse, or other safety device has been tripped. - Liquid is spilled into the copier/printer. - The equipment is exposed to water. - Any part of the equipment is damaged.

1 Safety Notes

Wide Format Copy System User Guide 3

Disconnect Device

The power cable is the disconnect device for this equipment. It is attached to the back of the machine as a plug-in device. To remove all electrical power from the equipment, disconnect the power cable from the electrical outlet.

Operational Safety Information To ensure the continued safe operation of your Xerox/Fuji Xerox equipment, follow these safety guidelines at all times.

Do These:

- Always connect equipment to a correctly grounded power outlet. If in doubt, have the outlet checked by a qualified electrician.

- This equipment must be connected to a protective grounded circuit.

This equipment is supplied with a plug that has a protective grounding pin. This plug will only fit into a grounded electrical outlet. This is a safety feature. To avoid risk of electric shock, contact your electrician to replace the electrical outlet if you are unable to insert the plug into it. Never use a plug that lacks a grounded connection terminal to connect the product to an electrical outlet.

- Always follow all warnings and instructions that are marked on or supplied with the equipment.

- Always exercise care when moving or relocating equipment. Please contact your local Xerox/Fuji Xerox Service Department or your local support organization to arrange relocation of the product to a location outside your building.

- Always locate the equipment in an area that has adequate ventilation and room for servicing. See the Install guide for minimum dimensions.

- Always use materials and supplies specifically designed for your Xerox/Fuji Xerox equipment. Use of unsuitable materials may result in poor performance.

- Always unplug this equipment from the electrical outlet before cleaning.

Do Not Do These:

- Never use a plug that lacks a grounded connection terminal to connect the product to an electrical outlet.

- Never attempt any maintenance function that is not specifically described in this documentation.

- This equipment should not be placed in a built-in installation unless proper ventilation is provided. Please contact your Authorized Local Dealer for further information.

- Never remove covers or guards that are fastened with screws. There are no operator serviceable areas within these covers.

- Never locate the equipment near a radiator or any other heat source. - Never push objects of any kind into the ventilation openings. - Never override or cheat any of the electrical or mechanical interlock devices. - Never operate the equipment if you notice unusual noises or odors. Disconnect the power

cord from the electrical outlet and contact your local Xerox/Fuji Xerox Service Representative or Service Provider immediately.

1 Safety Notes

4 Wide Format Copy System User Guide

Maintenance Information Do not attempt any maintenance procedure that is not specifically described in the documentation that is supplied with your copier/printer. - Do not use aerosol cleaners. The use of cleaners that are not approved may cause poor

performance of the equipment, and could create a dangerous condition. - Use supplies and cleaning materials only as directed in this manual. Keep all of these

materials out of the reach of children. - Do not remove covers or guards that are fastened with screws. There are no parts behind

these covers that you can maintain or service. - Do not perform any maintenance procedures unless you have been trained to do them by an

Authorized Local Dealer or unless a procedure is specifically described in the user manuals.

Ozone Safety Information This product will produce ozone during normal operation. The ozone produced is heavier than air and is dependent on copy volume. Providing the correct environmental parameters as specified in the Xerox installation procedure will ensure that the concentration levels meet safe limits. If you need additional information about ozone, please request the Xerox publication Ozone by calling 1-800-828-6571 in the United States and Canada. In other markets please contact your Authorized Local Dealer or Service Provider.

For Consumables Store all consumables in accordance with the instructions given on the package or container. Keep all consumables away from the reach of children. Never throw toner, toner cartridges, or toner containers into an open flame

Radio Frequency Emissions United States, Canada, Europe, Australia/New Zealand:

NOTE: This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense. Changes and modifications to this equipment not specifically approved by Xerox/Fuji Xerox may void the users authority to operate this equipment. Shielded interface cables must be used with this equipment to maintain compliance with FCC regulations in the United States and the Radio Communications Act 1992 in Australia/New Zealand as applicable.

1 Safety Notes

Wide Format Copy System User Guide 5

Product Safety Certification This product is certified by the following agencies using the Safety standards listed.

Agency Standard TUV Rhineland of North America UL60950-1 1st (2003) (USA/Canada) NEMKO IEC60950-1 Edition 1 (2001)

This product was manufactured under a registered ISO9001 Quality system.

Regulatory Information

The CE mark applied to this product symbolizes Xeroxs declaration of conformity with the following applicable Directives of the European Union as of the dates indicated:

January 1, 1995: Council Directive 72/23/EEC amended by Council directive 93/68/EEC, approximation of the laws of the member states related to low voltage equipment.

January 1, 1996: Council directive 89/336/EEC, approximation of the laws of the member states related to electromagnetic compatibility.

March 9, 1999: Council Directive 99/5/EC, on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity.

A full declaration of conformity, defining the relevant directives and referenced standards, can be obtained from your Authorized Local Dealer.

WARNING: In order to allow this equipment to operate in proximity to Industrial Scientific and Medical (ISM) equipment, the external radiation from the ISM equipment may have to be limited or special mitigation measures taken.

WARNING: This is a Class A product. In a domestic environment the product may cause radio frequency interference, in which case the user may be required to take adequate measures.

WARNING: Shielded interface cables must be used with this product to maintain compliance with Council Directive 89/336/EEC.

1 Safety Notes

6 Wide Format Copy System User Guide

Wide Format Copy System User Guide 7

2 Getting to know the Wide Format Copy System

This manual contains operating instructions for the user and the system administrator for the Xerox Wide Format Copy System 510 Series, 721P, 6030/6050/6050A, 6204, and 6279 with version 13.0 FreeFlow Accxes firmware loaded into the Controller.

NOTE: For the 6030/6050/6050A, 6204 and 6279 printers that want to use the FreeFlow Accxes firmware features, the printer also needs to be connected to a separate PUN, YKE, or FRX, or LVX controller, referred to as the FreeFlow Accxes Print Server. The Web Printer Management Tool software will be loaded on the print server.

Your Xerox Wide Format Copy System is an integrated solution for electronically scanning and then printing good quality copies of the images for engineering or architectural size documents. The Wide Format Copy System consists of the Wide Format Scan System and Control Panel for capturing images, the FreeFlow Accxes Controller for processing these images, and Xerox Wide Format Copy System Printers 510 Series, 721P, 6030/6050/6050A, 6204, or 6279.

The 6204 and 6279 printers can also be installed with a built-in scanner. See the Xerox 6204 Wide Format Solution Copy/Scan User Guide for the FreeFlow Accxes Print Server V13.0 or the Xerox 6279 Wide Format Solution Copy/Scan User Guide for the FreeFlow Accxes Print Server V13.0. These guides provide comprehensive scan instructions for their unique touch screen user interfaces.

The Wide Format Copy System has two modes of operation - COPY and SCAN.

In the COPY mode:

Documents are scanned, temporarily stored in memory or on the FreeFlow Accxes controller hard drive, and then sent to the local Printer as soon as the Printer is available.

In the SCAN mode:

Scan-to-Net: Documents are scanned and then stored on the FreeFlow Accxes Controller hard drive for later retrieval over a network by a remote device. Scan to Remote Destination: Scanned images can be transferred to up to 16 remote FTP or printer destinations. Scan to FTP images are not stored on the FreeFlow Accxes Controllers hard drive. Scan to remote printer images are stored on the FreeFlow Accxes Controllers hard drive. The FTP and Remote Printer features are located on the Sample Mode screen. See the Sample Key section of this guide for more information.

The Wide Format Copy System allows concurrent printing, copying, and scanning to the network, so there is no need to wait for the Printer to finish before scanning the next document.

2 Getting to know the Wide Format Copy System

8 Wide Format Copy System User Guide

The XEROX Wide Format Copy System contains Dynamic Background Suppression technology. Dynamic Background Suppression examines a sample of the document intelligently and makes automatic image quality adjustments that yield a good copy even from poor original documents. The document width is automatically detected and the centering of a scanned original for most opaque documents is adjusted. Translucent documents (transparencies, clear film, etc.) in most cases will not be detected.

The Productivity feature was introduced with version 10.0 firmware and requires that a new WIDE FORMat Scan SYSTEM have a new Document Feed-in Tray. Sensors built into the Feed Tray measure the document width without doing a prescan, which increases the document and copy throughput, thereby increasing productivity.

NOTE: Documents must be centered when using the sensors for width detection.

For documents that require additional adjustments to obtain the best copy quality, a variety of image quality and reduction/enlargement settings are available. All of these functions are controlled from the Scan System Control Panel. This Control Panel, which is mounted on top of the Scan System, receives all power and information from the Scan System.

Feature Keys Print and Copy feature keys are standard for all printers using FreeFlow Accxes 13.0 firmware, except for the Xerox Wide Format 6030/6050 Printer. In the 13.0 firmware, the following feature keys need to be loaded before the features can be used. See the Feature Key instructions and Coupon Exchange screens on the www.xerox.com website.

NOTE: See the Configuration < Features page on Web Printer Management Tool for a list of available Accxes, Printer, and Scanner features. This page lists whether the feature is installed and provides its current status (enabled or disabled).

Xerox Wide Format Scan System Features:

Scan-to-Net Feature Key to create an electronic file from a scanned image.

Scan-to-Print Feature Key to scan, create a preview, and send the scanned image to the printer when the Scan-to-Net feature is present.

Color Enablement Feature Key allows color scanning when the Scan-to-Net feature is present.

Speed Enhancement Turbo II Feature Key 4 inches per second (ips) for 36 wide media.

Speed Enhancement Turbo III Feature Key PUN, YKE, YKE-N, FRX and LVX Controllers only: 7.33 ips in Copy Mode.

Xerox Wide Format 6030/6050 Printer: Print Server Enablement Feature Key Enables print and copy mode for a remote printer.

Xerox Wide Format Printers:

5D Speed Update Feature Key Enables updated printer speed from 4D to 5D/minute for the 6204 Printer.

9D Speed Update Feature Key Enables updated printer speed from 7D to 9D/minute for the 6050A and 6279 Printers.

Additional 2 roll drawer upgrade 6279.

Additional 2 cut sheet tray upgrade 18 24 maximum size 6279.

2 Getting to know the Wide Format Copy System

Wide Format Copy System User Guide 9

Xerox Wide Format Printers and Scan Systems: Job Accounting Feature Key Job accounting enables the tracking of media usage data. The Account Management Tool (AMT), or some other external accounting tool, is used to assign a User ID, Account ID, and Printer ID. It then collects and tallies the stored data from the printers.

PostScript Feature Key This enables the interpretation of Adobe Post Script 3, PDF 1.6 for the YKE, YKE-N, FRX and LVX Controller, 1.3 for HFT, and PDF 1.6 for all other FreeFlow Accxes Controllers. Disk Image Overwrite Feature Key Enables the security options for overwriting image data on the hard drive. The immediate overwriting of data to DOD specification is such that the system, at any point in its operation, can be considered secure and all data will be removed no matter what operation the customer is performing.

OS Enablement Feature Key Enables the YKE, YKE-N, FRX, and LVX controller to print, copy, and scan.

AutoCAD Enables interpretation of DWF files.

Other CAD Enables interpretation of DGN files.

Raster JPEG2000, BMP, PNG, GIF.

NOTE: The Special Features Key section of this document refers to physical buttons (keys) that are on all the Xerox Wide Format Scan Systems.

2 Getting to know the Wide Format Copy System

10 Wide Format Copy System User Guide

Scan System Standard Components The illustrations below show the components of the Wide Format Scan System. These components are standard on the XEROX Wide Format Copy System 6030/6050/6050A, 6204, 6279, and 510 Series. With the exception of the Stand and Standard Organizer, the components are standard on the 721P. Following the illustrations are descriptions of each of the components.

Wide Format Scan System Front View

A. Document Handler

Raise the Document Handler for routine maintenance functions and to access the optical paper sensors for diagnostic routines.

B. Scan System Control Panel

The control panel allows the selection of options and features and contains a graphical display for the communication of information and instructions. Refer to Scan System Control Panel for additional information.

C. Thick Document Lever

The Thick Document Lever is used to adjust the Scan System for thick documents and to remove documents from the Scan System feed mechanism. When setting the thickness for a document, raise the lever to the next thickness. If the document slides past the Feed Rolls into the Document Handler, lower the Lever to the next position.

D. Stand

The Stand is standard with the XEROX Wide Format Copy System 6030/6050/6050A, 6204, and 510 Series. It is optional with the 721P.

A B

C

D

F

2 Getting to know the Wide Format Copy System

Wide Format Copy System User Guide 11

E. Standard Organizer (not shown in previous photo)

The Organizer is located on the front of the Scan System. It is useful for holding multiple documents that are to be scanned.

It has two extensions at its end that can be pulled out to accommodate longer documents (up to size E or A0).

F. Productivity Document Feed Tray

Insert documents to be scanned face down and centered into the Document Feed Tray. This provides built-in Document Width Sensors that eliminate the need to prescan documents to measure width. This increases the document throughput, resulting in higher productivity.

Wide Format Scan System Rear View

A: Standard Stacker D: Power Cord and Connector B: Document Exit Slot E: Status Indicator LED C: Power On/Off switch F: IEEE 1394 Cable and Connector

NOTE: Components shown above with the exception of the Standard Organizer are also available on all Wide Format Scan Systems

2 Getting to know the Wide Format Copy System

12 Wide Format Copy System User Guide

A. Standard Stacker

The Stacker is located at the rear of the Scan System. When the AUTORETURN feature is set to REAR, documents exit the Scan System onto the Stacker. The Stacker can be adjusted to any one of four positions by raising or lowering it. The height of the Stacker should be adjusted to accommodate the document being scanned. It has two extensions at its end that can be pulled out to accommodate longer documents (up to size E or A0). When scanning most common weight (20 lb, 80gsm) documents, move the Stacker to the 2nd rung from the bottom.

NOTE: All thick documents, and documents over 36 inches (914 mm), exit from the rear of the Scan System (regardless of the AUTORETURN setting). When scanning thick documents, the Stacker must be set to the lowest position for optimum performance.

B. Document Exit Slot

When the DOCUMENT RETURN feature is set to REAR, documents exit the Scan System through this slot and are delivered to the rear Stacker.

C. Power On/Off Switch

This switch turns the Scan System on and off. Press this switch to the on (I) position to turn on the Scan System and to the off (O) position to turn off the Scan System.

D. The Power Cord supplies power to the Scan System. Plug one end of the cord into the Scan System and the other end into an electrical outlet.

E. Status LED

The digital status LED provides an indication of the condition of the Scan System and communications with the FreeFlow Accxes Controller. A letter P, displayed on the LED Display on the rear of the Scan System, indicates that the Scan System is operating normally and has established communications with the controller.

F. IEEE 1394 Cable and Connector

The IEEE 1394 Cable is the communications link between the Scan System and the Controller. Plug one end of the cable into either one of the IEEE 1394 connections at the rear of the Scan System. Plug the other end into the IEEE 1394 connection on the Controller.

2 Getting to know the Wide Format Copy System

Wide Format Copy System User Guide 13

Scan System Compact Components The illustrations show the optional compact Stacker and organizer that are available for the Wide Format Scan System. The compact components allow the XEROX Wide Format Copy System to be installed in sites where space requirements are at a premium.

Front View of the Wide Format Scan System

A: Compact Organizer

Back View of the Wide Format Scan System

A: Compact Stacker

A

2 Getting to know the Wide Format Copy System

14 Wide Format Copy System User Guide

Scan System Control Panel The Scan System Control Panel is divided into three sections:

The options keys section (A), which contains the - Media Selection, Image Quality, and Reduce/Enlarge options selections

The graphical display (B) and the navigation keys (F) section.

The right-hand section, which contains the numeric keypad (D), the special features keys (E), and the scan control keys (C).

If the BEEP function is enabled (factory default), a beep sound will be heard when a key is pressed. If an incorrect key is pressed, a multiple beep sound will be heard.

Scan System Control Panel

A: Option Keys section D: Numerical Key pad

B: Graphical Display E: Special Features keys

C: Scan Control keys F: Navigation keys

A

B

D C

E

F

2 Getting to know the Wide Format Copy System

Wide Format Copy System User Guide 15

Option Keys The left side of the Scan System Control Panel contains the keys for the selection of options. It is divided into three areas - Media Selection, Image Quality, and Reduce/Enlarge.

To select an option, press the key(s) beneath the option. In some cases, a screen requiring a selection or input is displayed on the graphical display. When an option is selected, the indicator lamp to the left of the option illuminates.

The illustration below depicts the options portion of the Scan System Control Panel.

Control Panel Options Area

Media Selection The Media Selection area of the Scan System Control Panel allows you to select the media Source, Type, and Output Format. The illustration below depicts the Media Selection portion of the control panel.

Media Selection Area

2 Getting to know the Wide Format Copy System

16 Wide Format Copy System User Guide

Source The Source option allows you to select the source of the media on which the image will be printed. To select the media source, press the key beneath the Source settings until the desired source indicator lamp illuminates.

The Source settings are:

Sheet This setting tells the Printer to print from a manually inserted sheet of media.

R4 This setting is applicable to the Wide Format Copy System 721P, 6050, 6050A and 6279. When R4 is selected, both the R1 and R3 indicator lamps illuminate and the Printer then selects the media stored on Roll 4.

R3 When it is selected, the R3 indicator lamp illuminates and the Printer selects the media stored on Roll 3.

R2 This setting tells the Printer to select the media stored on Roll 2.

R1 This setting tells the Printer to select the media stored on Roll 1.

For the Xerox Wide Format 6279 printer and 6279 multifunction configuration:

When 3 Tray is selected, the R3 indicator lamp illuminates and the Printer selects the media stored in Tray 3. When 4 Tray is selected, the R1 and R3 indicator lamps illuminate and the Printer then selects the media stored in Tray 4.

Auto (factory default) This setting automatically selects the roll containing the media that best fits the size of the captured image. For most documents, the Scan System is able to automatically detect the width of the scanned document. This permits the Auto function to automatically select the most appropriate roll of media.

NOTE: The presence of the Sheet feature and the amount of rolls available vary by the type of WIDE FORMAT PRINTER. If these options are not installed, they cannot be selected. To print from a cut sheet, Sheet mode must be explicitly selected. The Auto mode cannot select a cut sheet.

Type The Type option allows you to select the kind of media on which to print Bond, Vellum/Tracing, or Film. To select the media type, press the key beneath the Type settings until the desired type indicator lamp illuminates.

2 Getting to know the Wide Format Copy System

Wide Format Copy System User Guide 17

NOTE: Only media types actually loaded into the Printer can be selected. When a roll is selected, the media type for that roll is automatically selected also. If more than one media type is loaded when the media source is set to Auto, the default choice priority is Bond (first), Vellum (second), and Film (third). Refer to the applicable Printer Operator Manual for instructions about how to load rolls and specify the width and media type.

Output Format The Output Format option allows you to select the size to which the roll feed media will be cut. It has three modes Manual, Preset, and Synchro.

Manual Manual allows you to enter the desired length and width manually.

To select the Manual mode:

1. Press the key beneath Output Format until the Manual indicator lamp illuminates. The CUSTOM OUTPUT FORMAT screen is displayed.

NOTE: If the indicator lamp is already lit, press the key once to display the screen.

CUSTOM OUTPUT FORMAT ENTER CUSTOM MEDIA SIZE: WIDTH (11.0 -36.0): 11.0 IN LENGTH (8.3 1200.0): 8.5 IN

Custom Output Format Screen

2. Press the Previous or Next key to select WIDTH or LENGTH.

3. Press the Enter key to confirm the choice.

4. Use the numeric keypad to enter the desired value.

NOTE: The entered value must be within the limits shown in parentheses on the screen.

5. Press the Enter key to confirm the value.

6. Repeat steps 3 to 5 to enter the value for the remaining setting.

7. When the values for WIDTH and LENGTH are correct, press the Exit key to return to the READY screen.

Preset Preset allows you to select a predefined length to which the roll media should be cut during printing. The associated width specification will depend on the Media Source selection. If the Media Source selection is set to Auto, the system will select the roll of media that best matches the width specification. If Media Source is set to R1, R2, R3, or R4; the system will use the selected roll regardless of the width specification.

To select the Preset mode:

1. Press the key beneath Output Format until the Preset indicator lamp illuminates. The PRESET OUTPUT FORMAT screen is displayed.

NOTE: If the indicator lamp is already lit, press the key once to display the screen.

2 Getting to know the Wide Format Copy System

18 Wide Format Copy System User Guide

PRESET OUTPUT FORMAT

SELECT: 8.5 X 11 ANSI A

Preset Output Format screen

2. Press the Previous or Next key to select an item from the list.

NOTE: Formats can be added or removed from this list. Refer to Custom Media Formats in the Main Menu section for more information.

3. Press the Enter key to confirm the choice and return to the READY screen.

Preset Auto Preset Auto allows you to print on a standard size sheet if the document is a little bigger or a little smaller than the standard size.

To select the Preset Auto mode:

1. Press the key beneath Output Format until the Preset indicator lamp illuminates. The PRESET OUTPUT FORMAT screen is displayed.

2. Press the Previous or Next key to select an item from the list.

3. Press the Enter key to confirm the choice and return to the READY screen.

Synchro When the Synchro mode is selected, the length of the original is measured as it passes through the Scan System and automatically cuts the media at the Printer to match the length of the original document. Synchro is the factory default. To select the Synchro mode, press the key beneath Output Formats until the Synchro indicator lamp illuminates.

2 Getting to know the Wide Format Copy System

Wide Format Copy System User Guide 19

Image Quality Area The Image Quality area of the Scan System Control Panel allows you to make corrective adjustments to the image and extract the best possible copy quality from an original document. It contains the Type, Background Suppression, and Copy options.

The illustrations below depict the Image Quality portion of the Control Panel for FreeFlow Accxes software version 12.0 or higher and SCAN SYSTEM firmware version 3.2.6 or higher.

Image Quality Area

The SCAN SYSTEM firmware must be at version 3.2.6 or greater to support Normal, Line, Photo, or Color Type. If the SCAN SYSTEM is not at the required version, there will be an error message.

Depending on what Mode is selected (COPY or SCAN) the message will be displayed as show below.

Invalid Mode in Copy Mode

INVALID MODE

UPGRADE SCANNER FIRMWARE

AUTO

1 100.0 %

2 Getting to know the Wide Format Copy System

20 Wide Format Copy System User Guide

Invalid Mode screen in Scan Mode

Original, Type

The Type option allows you to specify the type classification of your document. To select the document type, press the key beneath the Type settings until the desired Type indicator lamp illuminates.

Normal Normal (factory default) Select Normal for most copying needs. This setting will provide good image quality for copying most types of drawings containing text, line art, or a mixture of these. Shaded areas will be preserved. The TIFF, CALS, PDF and JPEG file types are available for Normal images.

In the SCAN mode, the following screen is displayed when the Normal key is pressed.

FORMAT: TIFF

PREVIEW

Scan Options (Normal) Screen

INVALID MODE UPGRADE SCANNER FIRMWARE

TIFF/CCITTG4 1 BIT

400 DPI

2 Getting to know the Wide Format Copy System

Wide Format Copy System User Guide 21

Line Line Select Line for an image containing fine lines, especially pencil. This selection produces high contrast and dark black images. The TIFF, CALS, PDF and JPEG file types are available for Line images. If the Mode selected is SCAN, and the Scan-to-Net feature key is installed, the SCAN OPTION (LINE) screen will be displayed. If the COPY mode is selected, the READY TO COPY screen will be displayed. Refer to the "Image Quality" section of this manual for additional information.

SCAN OPTIONS (LINE)

FORMAT: TIFF

PREVIEW

Scan Options (Line) Screen

Photo Photo Select Photo when the document contains a gray scale or color image, such as a photograph. TIFF, PDF, and JPEG file types are available for Photo images. If the Copy Mode is selected, the READY TO COPY screen will be displayed. In Scan Mode, the following screen will be displayed. Refer to the Image Quality section of this manual for additional information.

SCAN OPTIONS (PHOTO)

COMPRESSION:

FORMAT:

RAW TIFF

PREVIEW

Scan Options (Photo) Screen

NOTE: The Background Suppression option cannot be used with the Photo setting. If Photo is selected, Background Suppression is automatically set to OFF.

Color

Color Color is only selectable in the SCAN mode. Select Color when scanning full color documents. When Color Type is selected, a version of the following screens will be displayed. The content of the screen will depend on the selected FORMAT and COMPRESSION.

The following screens will only be displayed in SCAN mode when the Scan-to-Net and Color Enablement feature keys are installed. The Normal and Photo LED's will be lit when Color is selected.

The selections that appear on the screen depend on the FORMAT and COMPRESSION selections.

2 Getting to know the Wide Format Copy System

22 Wide Format Copy System User Guide

SCAN OPTIONS (COLOR)

COMPRESSION:

FORMAT:

: PACKBITS

: TIFFPREVIEW

Scan Options (Color) Screen - Packbits Compression Selection

SCAN OPTIONS (COLOR)

COMPRESSION:

FORMAT:

INDEX

: TIFF

PALETTE: DEFAULT

PREVIEW

Scan Options (Color) Screen - Index Compression Selection

SCAN OPTIONS (COLOR)

COMPRESSION:

FORMAT:

NORMAL

JPEGPREVIEW

Scan Options (Color) Screen Normal Compression Selection

Background Suppression The Background Suppression option enables you to make adjustments for documents that contain poor contrast between the foreground image and the background.

Four Background Suppression choices are provided:

Off This setting disables Background Suppression. All the characteristics of the original document with minimum alteration are reproduced on the copy. Choose this selection when:

The lead edge of the document is very different from the rest of the document (e.g., the lead edge contains a black border).

Maps with grayscale or color content may copy best in this mode.

To retain more light color information, such as light gray or yellow.

NOTE: If Photo or Color is selected as the Original, Type, the Off setting is automatically selected. The contrast can still be adjusted by pressing the key(s) beneath Image Quality, Copy.

2 Getting to know the Wide Format Copy System

Wide Format Copy System User Guide 23

(Light) This setting works best for documents on translucent or transparent media, such as vellum (tracing paper) or film, or with medium levels of colored background on opaque media or for documents. Such documents have a higher contrast between the foreground and background than dark documents, but less contrast than normal documents.

(Dark) Use this setting for documents with a dark background or with medium contrast between the foreground and background. In this mode, the background is not suppressed, but the foreground image is improved to increase the contrast.

Auto (factory default) The Scan System automatically adjusts the image quality parameters to obtain the best copy.

NOTE: All three Background Suppression settings can be adjusted further by changing the contrast setting in the Image Quality and Copy area.

Background Suppression can operate in either the dynamic or static mode.

Select the Menu key> CONFIGURATION>IMAGE ENHANCEMENT.

IMAGE ENHANCEMENT

COLOR IQ: SRGBCOLOR IQ:

DYNAMIC BACKGROUND REMOVAL

SRGB NORMAL MODE: BEST IQ

Image Enhancement Screen

When enabled, the dynamic mode will monitor the whole document and adjust the image quality settings as the document is being scanned in order to optimize the background of the copy.

When disabled, the static mode monitors the first two inches to establish a background threshold that is used throughout the document in order to optimize the background of the copy.

Static Background Suppression is not available in the PRODUCTIVITY mode.

Copy The Copy option allows you to darken or lighten the contrast of the copy with respect to the original document. Press the down arrow key to darken the contrast. Press the up arrow key to lighten the contrast. The indicator lamp for the selected contrast setting illuminates. The middle contrast setting is the factory default setting.

You can use this feature to further adjust the effects of the Type and Background Suppression selections. The feature operates with all four Background Suppression modes.

NOTE: Copy is not selectable in Color mode.

2 Getting to know the Wide Format Copy System

24 Wide Format Copy System User Guide

Reduce/Enlarge The Reduce/Enlarge area of the Scan System Control Panel allows you to select one of three reduction/enlargement modes - Auto, Manual, and Preset. The illustration below depicts the Reduce/Enlarge portion of the Control Panel.

NOTE: Reduce/Enlarge can only be selected in Copy mode.

Reduce/Enlarge Area

Auto Auto automatically adjusts the reduction/enlargement to fit the size of media selected. To select the Auto mode, press the key beneath Reduce/Enlarge until the Auto indicator lamp illuminates.

NOTE: The size of the output media must be known in advance for this feature to operate. Therefore, Auto is not a valid selection if both the Synchro cut option and the Sheet and Auto media source options are selected. If you select this combination, an INVALID AUTO COMBINATION status is displayed.

Manual Manual allows you to reduce the image captured by the Scan System to as little as 25%, or as much as 400%, of the original size before the copy is printed.

To select the Manual mode:

1. Press the key beneath Reduce/Enlarge until the Manual indicator lamp illuminates. The MANUAL REDUCTION/ENLARGEMENT screen is displayed.

NOTE: If the indicator lamp is already lit, press the key once to display the screen.

2 Getting to know the Wide Format Copy System

Wide Format Copy System User Guide 25

MANUAL REDUCTION/ENLARGEMENT

ENTER (25.0 400.0): 100.0%

Manual Reduction/Enlargement Screen

2. Enter a reduction/enlargement between 25 and 400. You can select any value between these limits in 0.1% increments.

3. Press the Enter key to confirm your choice and return to the READY screen. The READY screen now displays the new reduction/enlargement percentage.

NOTE: Pressing the Exit key rejects the choice and retains the previous setting.

Preset Preset (factory default) allows you to select a predefined reduction or enlargement percentage.

To select the Preset mode:

1. Press the key under Reduce/Enlarge until the Preset indicator lamp illuminates. The PRESET REDUCTION/ENLARGEMENT screen is displayed.

NOTE: If the indicator lamp is already lit, press the key once to display the screen.

PRESET REDUCTION/ENLARGEMENT

SELECT: 100.0%

Preset Reduction/Enlargement Screen

2. Press the Previous or Next key until the desired reduction/enlargement ratio is displayed. The possible choices are any combination of the following:

50%, 100% (default), and 200%

65% and 129%, if the ANSI and ARCH sizes are enabled

71% and 141%, if the ISO A, ISO B or JIS B sizes are enabled

Up to six additional preset values, if these values have been defined using the CUSTOM R/E presets menu functions.

NOTE: Refer to Media Series in the Main Menu section for more information about enabling media series and defining custom presets.

3. Press the Enter key to confirm your choice and return to the READY screen. The READY screen now displays the new reduction/enlargement percentage.

NOTE: Pressing the Exit key rejects the choice and retains the previous setting.

2 Getting to know the Wide Format Copy System

26 Wide Format Copy System User Guide

Graphical Display and Navigation Keys The middle portion of the Scan System Control Panel contains the graphical display and the navigation keys. The illustration below depicts the middle portion of the Control Panel.

Navigational Keys and Graphical Display Area

Graphical Display The graphical display provides you with information and instructions pertaining to the system. It consists of up to four lines of text and graphics. The display can be adjusted upward for better viewing.

Navigation Keys The navigation keys, located beneath the display, are used to move through the menu screens, to select items on the screen, and to specify parameters when an options screen is displayed. Some keys have more than one function depending on the screen being displayed at the time. These special functions are explained in later sections.

Menu The Menu key invokes the main menu. If a menu screen is already being displayed, pressing this key exits the menus and directly returns you to the previous READY State.

Previous The Previous key highlights the previous item in a displayed list.

Next The Next key highlights the following item in a displayed list.

Enter The Enter key either confirms the selection of the currently highlighted item or confirms an entered numeric value.

Exit The Exit key cancels a selection operation and returns you to a previous screen. It has other effects, depending upon the specific situation, that are explained later.

Mode The Mode key is a valid selection only when READY is displayed on the screen. This key is used to switch between the READY TO COPY mode and the READY TO SCAN mode. The SCAN mode can be entered only if the Scan-to-Net feature key is loaded.

Below are examples of the READY screen in COPY and SCAN modes.

2 Getting to know the Wide Format Copy System

Wide Format Copy System User Guide 27

Ready to Copy Screen for Roll Media

Ready to Copy Screen for Tray Media (6279 makes a cut sheet tray option available)

READY TO SCAN INSERT DOCUMENT

400TIFF/CCITTG4 11 BIT

Ready to Scan Screen

In the COPY mode, the scanned image or set of images is printed on the Printer and then deleted from the hard disk.

In the SCAN mode, the scanned image or set of images is stored on the hard disk for later retrieval over a network by a client running on a remotely located device. Scanned images can also be transferred to four remote FTP destinations from the Samples Mode screen. Refer to the Scanning to the Network section for more information about the SCAN mode.

NOTE: The SCAN mode is an optional feature that is enabled by installing the Scan-to-Net feature key. Contact your XEROX representative for ordering information.

2 Getting to know the Wide Format Copy System

28 Wide Format Copy System User Guide

Numeric Keypad and Special Features/Control Keys The right side of the Scan System Control Panel contains a numeric keypad for entering quantities, keys for selecting other features, and keys for controlling the scanning and printing of images. To the left of some of the keys are indicator lamps that illuminate when the associated feature has been selected.

Stop Start

1

Transform Sample

Printer Interrupt

Store/ Recall

Batch

Sets Build

Finisher

A B C

4 5 6

7 8 9

3

0 C/CA/.

2 D E F

G H I J K L M N O

P R S T U V W X Y

Numeric Keypad

The numeric keypad contains the 0 to 9 numeric keys, the decimal key and the C/CA key.

Numeric (0-9) keys

These keys are used for numeric entry, password entry, and copy quantity fields.

NOTE: The letters next to the numbers are for entering User and Account Ids and Scan Directory information.

/. (Decimal key)

This key is used for entering alphanumeric values and string entries for account and user identities and directory names.

NOTE: The forward slash (/) to the left of the decimal is for future use.

C/CA (Clear/Clear All) key

This key has the following functions:

When in READY TO COPY mode, one press clears the current copy count to one. Two presses within one-second resets the copy parameters to the default settings.

When in READY TO SCAN mode, pressing this key brings up the CLEAR SCANNED IMAGE screen.

When in READY TO BUILD SET mode, pressing this key brings up the scanned document (Refer to Sets Build key section of this manual for additional information).

2 Getting to know the Wide Format Copy System

Wide Format Copy System User Guide 29

When in the entry state for numeric entry fields, pressing this key acts as a backspace/delete key. When the last digit is deleted, the numeric field goes to zero.

When in password entry and string entry fields, pressing this key acts as a backspace key. When the last character is deleted, the field is blank.

When in quantity entry fields, pressing this key clears the field to 1.

Special Features Keys The special features keys are used to activate, deactivate, or change parameters associated with special features. An indicator lamp adjacent to each feature key illuminates whenever the corresponding feature is activated.

The special features keys include the Printer Interrupt, Store/Recall, Finisher, Sets Build, Batch, Transform, and Sample keys. These keys are described in detail in the Special features keys section of this guide.

Scan Control Keys The Start and Stop keys control the scanning and printing of images.

Start key:

The Start key is used to begin the copy sequence when the AUTOSCAN feature is not enabled.

If you press the Start key while the status is NOT READY or INVALID AUTO COMBINATION, the system will beep to indicate an invalid key press. If you press the Start key while the status is READY TO COPY or READY TO SCAN, the document is scanned.

NOTE: INVALID AUTO COMBINATION indicates an incompatible combination of AUTO settings (i.e., Media Selection, Source set to Sheet or Auto, Media Selection, Output Format set to Synchro, and Reduce/Enlarge set to Auto).

Stop key:

The Stop key allows you to immediately stop the scanning operation to prevent damage to the document. Any scanned information is discarded. The READY screen prompts you to remove the document.

2 Getting to know the Wide Format Copy System

30 Wide Format Copy System User Guide

The Printer and the FreeFlow Accxes Controller For detailed operating instructions about the Printer and Controller components of the Wide Format Copy System and about network connectivity, refer to the documentation listed below.

FreeFlow Accxes System & Web Printer Management Tool Setup Guide

FreeFlow Accxes Controller Service Manual for HFT/PUN

Xerox FreeFlow Accxes Controller Service Manual for YKE/ YKE-N/FRX/LVX

Powering On the Wide Format Copy System To power on the XEROX Wide Format Copy Systems, you first must switch on the Scan System and wait for 30 seconds or check that a P is displayed on the status LED in the back of the Scan System. Then switch on the Printer, then the Controller.

Follow the instructions provided in this section for your system.

Initial Power-On For all controllers except the YKE, YKE-N, FRX and LVX controller, when the Wide Format Scan System is present, the DDS parameter must be set to Enabled in order to enable the COPY/SCAN functionality of the scanner. Go to the Web Printer Management Tool. Select Configuration > Printer > Printer Setup > DDS Enabled. Be sure that the DDS Enabled checkbox is selected. If the DDS Enabled checkbox is not selected, then the COPY/SCAN functionality will be disabled.

The default for this parameter is disabled. You must ensure that it is set to Enabled when powering on the Xerox Wide Format SCAN SYSTEM for the first time. After setting the DDS parameter, wait 30 seconds, and then power the system off then on. Once you enable this parameter, it will remain enabled (even following future software upgrades). For the Xerox Wide Format Copy System 510 Series, you can set this parameter from either the CONTROLLER CONFIGURATION screen of the Printer Control Panel or on the Web Printer Management Tool. For the Xerox Wide Format Copy System 6030/6050/6050A, 721P, 6204, and 6279 you can only set this parameter from the Web Printer Management Tool, (Configuration > Printer > Printer Setup > DDS Enabled).

2 Getting to know the Wide Format Copy System

Wide Format Copy System User Guide 31

Switching on the Scan System To switch on the Scan System, press the Power On/Off Switch on the back of the Scan System to the On (I) position as shown below. Wait for 30 seconds or until a P is displayed on the status LED.

Power Switch for the Scan System

When the Scan System is switched on, the fluorescent lamp inside the Scan System illuminates immediately. If the lamp does not illuminate, refer to the "Problem solving" section of this guide.

Switching on the PUN, YKE or LVX Controller and the Printer (Xerox Wide Format 510 Series/721P) Controller Power Switches

The YKE, PUN, and LVX Controller have their own power switch. First power on the Controller, and then power on the Printer.

SCAN SYSTEM Power Switch

YKE and LVX Controller Power Switch

2 Getting to know the Wide Format Copy System

32 Wide Format Copy System User Guide

Power Switch location on the PUN Controller

2 Getting to know the Wide Format Copy System

Wide Format Copy System User Guide 33

Switching on the Printer and the Controller (PUN, YKE, YKE-N, FRX, and LVX controllers)

NOTE: Ensure that the Scan System is switched on first and the P is displayed in the Status Indicator window before powering on the Controller.

The PUN controller and the FreeFlow Accxes Print Servers (YKE, FRX YKE-N, and LVX controllers) each have their own power switch.

When powering them on:

1. Power on the Printer.

2. Power on the Scan System.

3. Wait for the P to be displayed in the Status Indicator window of the Scan System.

4. Power on the Controller.

Power Switch location on the YKE-N, FRX, and LVX Controller.

2 Getting to know the Wide Format Copy System

34 Wide Format Copy System User Guide

721P Series Power Switch

510 Series Power Switch

2 Getting to know the Wide Format Copy System

Wide Format Copy System User Guide 35

Xerox 6030/6050/6050A Wide Format Power Switch

Xerox 6204 Wide Format Power Switch Note: The controller manages the power supplied to the Printer or Copier/Printer.

2 Getting to know the Wide Format Copy System

36 Wide Format Copy System User Guide

Xerox 6279 Wide Format Power Switch Note: The controller manages the power supplied to the Printer.

Xerox 6279 Wide Format Circuit Breaker

2 Getting to know the Wide Format Copy System

Wide Format Copy System User Guide 37

Powering the Xerox 6204 Wide Format Solution On/Off The following describes the procedure for powering the Xerox 6204 Wide Format Solution with FreeFlow Accxes Print Server on and off.

Powering On the System 1. Move the printer circuit breaker switch up, to the On [ | ] position.

2. Move the printer power switch to the On [ | ] position.

3. Press the power button on the front of the controller.

The power button lamp will illuminate. After about one-half minute, the control panel will display the message Printer Warming Up. The machine will be print-ready in about three minutes.

CAUTION: Powering down the system incorrectly may result in data corruption and a service call. The system shutdown procedure below allows the controller to power down correctly. Shutdown is best performed through the Web Printer Management Tool or the control panels System Administration menus [Shutdown] feature. Only authorized persons should power down the system fully.

Powering Off the System 1. Ensure that all jobs have finished processing, and that the indicator

on the control panel is not illuminated.

2. Select [Shutdown] from either the control panel or the Web Printer Management Tool.

From the control panel 1. Select the button and enter the System Administration password.

2. Select the [Shutdown] button. The [Power Off] screen will display briefly on the control panel, and then the control panel and the printer will shut down.

Power Button

Circuit Breaker

Printer Power Switch

2 Getting to know the Wide Format Copy System

38 Wide Format Copy System User Guide

The controller will complete its shutdown within 30 seconds from the moment the control panel and printer shut down. The controllers power button lamp will go out when the controller completes its shutdown.

From the Web Printer Management Tool The control panel, printer, and controller will undergo the same power down process as described above.

1. Select [Utilities > Shutdown > Shutdown].

2. Move the printer power switch to the off position.

3. Move the printer circuit breaker switch to the off position.

Powering the Xerox 6279 Wide Format Solution On/Off The following describes the procedure for powering the Xerox 6279 Wide Format Solution with FreeFlow Accxes Print Server on and off.

Powering On the System 1. Move the printer circuit breaker switch up, to the On [ | ] position.

2. Move the printer power switch to the On [ | ] position.

3. Press the power button on the front of the controller.

The Power Button indicator will illuminate. The Control Panel will display the message Printer Warming Up. The machine will be print-ready in about 3 minutes.

Power Button

Circuit Breaker

Printer Power Switch

2 Getting to know the Wide Format Copy System

Wide Format Copy System User Guide 39

CAUTION: Powering down the system incorrectly may result in data corruption and a service call. The system shutdown procedure below allows the controller to power down correctly. Shutdown is best performed through the Web Printer Management Tool or the control panels System Administration menus [Shutdown] feature. Only authorized persons should power down the system fully.

Powering Off the System 1. Ensure that all jobs have finished processing.

2. Select [Shutdown] from either the User Interface Control Panel or from the Web Print Management Tool.

From the control panel 1. Press the button, enter the System Administration password, and then

select the [Shutdown] button.

2. Select [System Administrator Log In].

3. Enter the System Administrator Password when the Password Screen displays.

4. Select [Shutdown] on the System Administrator Menu Screen.

5. Select [Shutdown] on the Shutdown Screen.

6. The [Power Off] screen will display briefly on the control panel, and then the control panel and the printer will shut down.

7. The controller will complete its shutdown within 30 seconds from the moment the control panel and printer shut down. The controllers power button indicator light will go out when the controller completes its shutdown.

8. Move the printer power switch to the off position.

9. Move the printer circuit breaker switch to the off position.

From the Web Printer Management Tool 1. Select [Utilities > Shutdown > Shutdown].

2. The control panel, printer, and controller will undergo the same power down process as described above.

3. Move the printer power switch to the off position.

4. Move the printer circuit breaker switch to the off position.

2 Getting to know the Wide Format Copy System

40 Wide Format Copy System User Guide

Scan System Warm-up The Scan System requires about 45 seconds to warm up and initialize after you power on the Wide Format Copy System. Once the initialization is complete, the READY screen is displayed. Below is an example of the READY screen.

READY TO COPY INSERT DOCUMENT

AUTO

1100.0 %

Ready to Copy Screen You can now insert a document into the Document Feed Tray of the Scan System. The Scan System will then transport the document to the starting position. This transportation of the document is called staging.

If you cannot insert a document into the feed mechanism and achieve staging after approximately 4 minutes, refer to the "Problem solving" section of this guide.

Powering off the System To power off the Wide Format Copy System, do the following:

1. Power off the Controller and the Printer.

For the 510 Series, switch the Circuit Breaker Switch to the Off (O) position. Then switch the Printer Switch to the Off (O) position.

For the 721P, first power off the Printer. Then power off the Controller.

2. Switch off the Scan System by pressing the Power On/Off Switch on the back of the Scan System to the Off (O) position as shown below.

Power On/Off Switch Photo

SCAN SYSTEM Power Switch

Wide Format Copy System User Guide 41

3 Document Quality

Document Quality Document quality is the primary factor in obtaining good copies from scanned originals. For most documents, the four Background Suppression key selections with DYNAMIC BACKGROUND REMOVAL enabled, which is the default setting, provides an accurate copy. Some documents, however, require manual adjustments to the settings.

This section explains the DYNAMIC BACKGROUND REMOVAL feature, describes the characteristics of good quality and bad quality documents, provides tips for preparing and organizing documents for scanning, and summarizes the procedures for scanning documents of different quality types.

Dynamic Background Removal NOTE: DYNAMIC BACKGROUND Removal cannot be disabled (unchecked) when using the Productivity mode.

The DYNAMIC BACKGROUND REMOVAL eliminates the need to make additional manual adjustments for most input documents. Select the Menu key > CONFIGURATION > IMAGE ENHANCEMENT.

This feature allows the system to dynamically adjust itself for each document. There are two modes associated with this feature:

When DYNAMIC BACKGROUND REMOVAL is enabled, the image is continually monitored as it is being scanned and the copy quality parameters adjusted to achieve the best copy quality.

When DYNAMIC BACKGROUND REMOVAL is not enabled, the process takes a 0.70 inch (17.8 mm) snapshot over the full width of the image after the first 1.5 inches scan. It uses this fixed area to set the copy parameters for the remainder of the image being scanned. This operating mode should be used for documents with consistent background throughout.

3 Document Quality

42 Wide Format Copy System User Guide

DYNAMIC BACKGROUND REMOVAL only monitors the document in the process direction, from the lead edge to the trail edge. It cannot make adjustment from the left side to the right side of the document. For example, if the input document is dark, DYNAMIC BACKGROUND REMOVAL will automatically make the appropriate compensation to optimize the reproduction of the dark details. If the input document has a faded background, the feature will enable a faithful reproduction of the original. However, the faded background must be inserted with the fading running in the process direction with the darker side being inserted first.

In some cases, you may wish to optimize the settings for individual documents. For example, you may not wish to faithfully reproduce paste-up lines, or other artifacts on the original. For this reason, additional controls are available for selection of document type, document image quality, desired output darkness, and background suppression.

The DYNAMIC BACKGROUND REMOVAL feature, when enabled, uses information about the document captured during the scanning process to set image quality settings. The system automatically adjusts for the darkness of the background and the image content throughout the length of the document. When not enabled, it only uses the information in a 0.70 (17.8 mm) area over the width of the document to establish the image quality settings. Therefore, best results can be obtained if the document is fed in with an edge that has a representative sampling of both the background and the foreground image.

The Dynamic Background Removal feature provides an accurate copy for most documents including blueline, blueprints, color line art/text, and mixed documents containing combinations of halftone and art, or photograph and art. For documents with inverted images, the INVERT function should be enabled. Refer to "Inverting an image" in the "Special features keys" section for instructions on the INVERT function.

Automatic Edge Detection and Document Centering The AUTOWIDTH /AUTOCENTER features enable the system to automatically detect the width and center of the document. In cases such as transparencies or translucent documents where automatic detection is not possible, a message will prompt you to enter the width manually. You then must center the document before inserting it into the Scan System.

You can enable/disable the AUTOWIDTH/CENTER feature at any time. Refer to "Scan System Control" in the "Main Menu" section of this manual for more information.

PRODUCTIVITY MODE: This feature became available with version 10.0 FreeFlow Accxes software, and requires a new Wide Format Scan System with the Productivity Document Feed Tray with the discrete width sensors. This feature measures the document width without doing a pre-scan, requiring the operator to manually align the document within the media size guidelines on the Feed-in Tray. The width sensors eliminate the need for a prescan, thereby increasing the overall throughput of the system, resulting in higher productivity.

When the PRODUCTIVITY MODE is used, the operator must select the media series, ANSI, ARCH, ISO A, CUSTOM, etc., since the number of sensors that can be provided cannot monitor every media series. The PRODUCTIVITY mode can be enabled/disabled at anytime. Refer to "Scan System Control" in the "Main Menu" section of this manual for more information.

Determining Document Quality Some documents require additional adjustments to obtain the best copy quality. Documents of good quality are easy to scan and usually give good copies on the first attempt. Documents of bad quality may require more than one attempt, using different settings, to obtain the best copy quality.

3 Document Quality

Wide Format Copy System User Guide 43

What is a good quality document?

4" 4"

Foreground Background

A good quality document has all of these characteristics:

The contrast between the foreground (the image of interest) and the background is high. The foreground may be color or black.

The foreground is a solid, high-density black or dark color (or dark blue on a blueline, or dark brown on a sepia). The foreground density is uniform. There is only one kind of foreground (e.g., there are no pencil additions on a blueline). If the document is of mixed type, the foreground is color.

If the document is white on black or white on blue, the foreground is clear white or nearly white, and the background is a solid, high-density black or dark color.

The background is white or light-colored and is free of speckling or other noise. The background density is uniform.

The document has no creases, folds, stains, tears or extraneous marks that the Scan System might interpret as foreground.

What is a bad quality document? Bad quality documents often require special attention to achieve a usable image. Fortunately, image processing technology is incorporated that can extract acceptable images from documents degraded by many kinds of problems.

A bad quality document has one or more of the following problems:

The foreground is light (e.g., a faded or overexposed blueprint or light pencil lines).

The foreground has variable density (i.e., some parts are dark and some parts are light).

The foreground consists of two or more densities or colors (e.g., pencil additions on an ink drawing, or pencil or ink additions on a sepia).

The background is medium dark or dark (e.g., underexposed blueprint).

The background has variable density.

The background has speckles.

The document has creases, folds, stains, tears, or extraneous marks that the Scan System might interpret as foreground.

3 Document Quality

44 Wide Format Copy System User Guide

Preparing documents When preparing documents for scanning, keep the following points in mind:

If documents have been stored rolled up, flatten them out. They will be much easier to handle if they have been stored flat for at least eight hours. The longer that documents have been stored flat, the easier it will be to scan them. Rolled-up documents will typically roll back up after being scanned.

If possible, sort the documents you are going to scan according to these guidelines:

First, group the documents by media type - bond, vellum or film. Within each document type, you can further group the documents by image type (e.g., blueprint, pencil, sepia, line, photo, mixed (photo and line, blueline and pencil), and so forth).

Line documents contain lines or text against a highly contrasted background.

Photo documents are continuous-tone or grayscale images.

Mixed documents contain both line elements and photo elements or halftone images.

Scanning groups of documents of the same type or series (ANSI, ARCH, etc.) minimizes the number of changes you will need to make to the Image Quality settings.

Next, divide the documents in each media type group into "good" and "bad" piles based on your evaluation of their foreground and background quality. See "What is a good quality document?" and "What is a bad quality document?" in this section for assistance in doing so.

By grouping the documents in this way, you can scan the good quality documents first. Then you can focus on the bad quality documents, which will require more attention.

Next, determine if any of the documents are inverted (i.e., white or light foreground against dark background). If any documents are inverted, refer to "Inverting an image" in the "Special features keys" section.

Finally, sort the documents by size or series (ANSI, ARCH, etc.). This minimizes the number of times you will need to change the Media Selection, Output Format settings when using preset or custom format sizes.

3 Document Quality

Wide Format Copy System User Guide 45

Scanning strategies When scanning documents, always try the default Image Quality settings first. Select the documents type: line, photo, mixed or colorand use the Original, Type, Normal, Line, Photo or Color default settings for that type. Color is a Scan-to-Net feature and only available in SCAN mode. These settings have been designed to give the optimum image quality for most documents.

If you have a special original type, you may want to try some of the advanced image processing features available on the Scan System. Table 1 describes the scanning strategies for special original types.

Table 1. Scanning Strategies for Special Documents

Type of original First step to try Second step to try Third step to try

Color photograph Set Original Type to Photo Mode Scan: Set Original Type to Color.

Set Original Type to Normal and Background Suppression to Off.

Color lithograph Mode COPY: Set Original Type to Normal. Mode SCAN: Set Original Type to Color.

Set Original Type to Normal and Background Suppression to Off.

Set Original Type to Photo.

Color map Mode COPY: Set Original Type to Normal. Mode SCAN: Set Original Type to Color.

Set Original Type to Normal and Background Suppression to Off.

Set Original Type to Photo.

Old blueprint or sepia with dark background

Set Original Type to Line and Background Suppression to Auto. Transform, Invert to ON

Set Original Type to Line, Background Suppression to dark original, Transform, Invert to ON.

Adjust the Copy contrast as required for best image quality.

Old blueprint or sepia with dark background and side-to-side fading

Set Original Type to Line and Background Suppression to Auto.

If fade is still visible in the copy, rotate the original 90 degrees. Generally, feeding the darkest edge first provides the best results.

Adjust the Copy contrast as required for best image quality.

Faded line/text drawing

Set Original Type to Line, Background Suppression to Auto.

If fade is still visible in the copy, rotate the original 90 degrees.

Adjust the Copy contrast as required for best image quality.

In reduction, use Reduction Line Preservation.

Line, photo or mixed original on film, clear film, vellum/tracing or other translucent media

Set Background Suppression to (light) and Normal. Select Photo for photo and select Line for line drawing. Use Normal for mixed documents.

Set Background Suppression to OFF.

3 Document Quality

46 Wide Format Copy System User Guide

This page has been intentionally left blank.

Wide Format Copy System User Guide 47

4 Image Quality

The Image Quality area of the Scan System Control Panel allows you to make adjustments for both the type of Original document and the output Copy to produce the best possible copy quality. It contains selections for Original (Document): Type and Background Suppression, and Copy options lighter or darker. There is also an IMAGE ENHANCEMENT selection in the Menu options that can be used in some copy jobs to improve the image quality. Press the Menu key and scroll to CONFIGURATION > IMAGE ENHANCEMENT.

The illustration below depicts the Image Quality portion of the Control Panel.

Image Quality Area

4 Image Quality

48 Wide Format Copy System User Guide

Original, Type The Type option allows you to specify the type classification of your document. To select the document type, press the key beneath the Type settings until the desired Type indicator lamp illuminates.

NOTE: The SCAN OPTIONS will not be displayed unless the Scan-to-Net feature is installed. To order this feature, contact your XEROX representative.

COPY MODE Type, Normal, Line, and Photo

The Type settings are: Normal, Line, and Photo. Color is only available in SCAN mode.

The Line mode scans with high contrast to provide exceptional copying of line drawings even light pencil is reproduced as a dark black line.

NOTE: Line mode should not be used with documents containing half toned images, as this may cause them to become too dark.

Select Photo mode when the document contains a gray scale or color image, such as a photograph.

Normal mode attempts to reproduce the document being scanned to provide the best image quality including halftones and shadings as well as fine lines.

1. Select the Line, Photo or Normal by pressing the arrow key below Original, Type.

READY TO COPY INSERT DOCUMENT

100.0% AUTO

1

Ready to Copy Screen

Additional image quality settings associated with Normal, Line, and Photo mode can be obtained by using the Menu key. Access the IMAGING menu to use the REDUCTION LINE PRESERVATION and the IMAGE ENHANCEMENT menu to use NORMAL MODE and DYNAMIC BACKGROUND REMOVAL.

2. Press the Menu key to enter the menu options.

3. Press the Previous and Next keys to scroll to the CONFIGURATION menu and press the Enter key.

4. Use the Previous and Next keys to scroll to the IMAGE ENHANCEMENT or COPY OPTIONS>IMAGING menu, and then press the Enter key.

5. Use Previous and Next keys to select the option, and then press the Enter key to select and enable the settings.

4 Image Quality

Wide Format Copy System User Guide 49

IMAGE ENHANCEMENT

COLOR IQ: SRGB

IMAGING

AUTO-ROTATE

MAXIMUM COPY LENGTH: 1200.0 IN

REDUCTION LINE PRESERVATION

Imaging screen

REDUCTION LINE PRESERVATION Selecting the checkbox will preserve fine lines in the original document when reducing images during copying in Normal and Line mode only.

MAXIMUM COPY LENGTH To see what your Scan Systems maximum copy length is, select the Menu key > Configuration > Copy Options > Imaging > Maximum Copy Length. The default is 100 feet. For the 6030/6050/6050A, the scanned copy would get cut off at 3 meters.

WARNING: Copy documents that are larger than the printers maximum capability will not print correctly, or may not print at all.

IMAGE ENHANCEMENT

COLOR IQ: SRGB COLOR IQ:

DYNAMIC BACKGROUND REMOVAL

SRGB

NORMAL MODE: BEST IQ

Image Enhancement Screen

NORMAL MODE BEST IQ provides the best image quality, but it is a slower scanning speed.

FASTEST provides a faster scanning speed with lower image quality. Its only available if the Turbo III Speed Enhancement feature key is installed.

DYNAMIC BACKGROUND REMOVAL The Dynamic Background Removal feature, when enabled, uses information about the document captured during the scanning process to set image quality settings. The system automatically adjusts for the darkness of the background and the image content throughout the length of the document. Refer to DYNAMIC BACKGROUND REMOVAL in the Document Quality section of this manual for additional information.

SCAN MODE Type and Normal

NOTE: SCAN mode will not be displayed unless the Scan-to-Net feature is enabled. To order this feature, contact your XEROX representative.

Normal mode attempts to reproduce the document being scanned to provide the best image quality including halftones and shadings as well as fine lines. To select the scan options for Color Mode:

1. Press the Mode key. The Please Enter Directory screen is displayed.

2. Enter the Directory Name. The READY TO SCAN INSERT DOCUMENT screen is displayed.

3. Select the Normal by pressing the arrow key below Original, Type key until the Normal light comes on. The SCAN OPTIONS (NORMAL) screen is displayed.

4 Image Quality

50 Wide Format Copy System User Guide

4. Use the Enter key to enable/disable checkbox selection and the Next or Previous Key to select options with a colon (e.g., FORMAT: TIFF).

The options available for selections displayed on the screen will change depending on the FORMAT and COMPRESSION that are selected. Listed below are the selections and available options and their definitions:

PREVIEW - Use this checkbox to enable or disable the generation of a preview image for your scanned document. Default is enabled (checkbox is checked). Accxes 13.0 allows for the selection of preview settings Line or Photo.

FORMAT - Use this selection to determine which format you would like to have the scanned image saved in, TIFF, CALS (1 BIT only) or PDF/A. Default is TIFF.

The screen shown below only appears in the SCAN mode. Additional image quality selections are available by pressing the Menu key and scrolling to CONFIGURATION>COPY OPTIONS>IMAGING or CONFIGURATION> IMAGE ENHANCEMENT. Refer to the Main Menu section of the manual for additional information on these selections.

SCAN OPTIONS (NORMAL) PREVIEW

FORMAT: TIFF

Scan Options (Normal) Screen

Type Line Line Select Line for an image containing text, line art, or a mixture of these. If the COPY mode is selected the READY TO COPY screen will be displayed. If the Mode selected is SCAN, and the Scan-to-Net feature key is installed, the SCAN OPTION (LINE) screen will be displayed.

SCAN OPTIONS (LINE)

FORMAT: TIFF

PREVIEW

Scan Options (Line) Screen

1. Select the Line by pressing the arrow key below the Original, Type key. The SCAN OPTIONS (LINE) is displayed.

2. Press the Previous or Next key to highlight the scan option you wish to change.

3. Select one of the following: PREVIEW DEFAULT IS ENABLED AND A CHECKMARK IS PRESENT IN

THE BOX. PRESS THE ENTER KEY TO ENABLE/DISABLE THE PREVIEW. WHEN PREVIEW IS ENABLED, A SMALL JPEG (.JPG) FILE IS CREATED DURING THE SCANNING PROCESS AND STORED ON THE HARD DISK, AS OF ACCXES 13.0 THE USER HAS THE ABILITY TO SELECT FROM EITHER LINE OR PHOTO PREVIEWS. THE FREEFLOW ACCXES CLIENT TOOLS

4 Image Quality

Wide Format Copy System User Guide 51

SOFTWARE, RUNNING ON A NETWORK CONNECTED TERMINAL, CAN USE THIS FILE TO DISPLAY A PREVIEW OF THE SCANNED IMAGE.

FILE FORMAT DEFAULT IS TIFF. USE THE NEXT AND PREVIOUS KEYS TO SELECT THE FORMAT FOR THE DOCUMENT TO BE SAVED AS. THE SELECTION IS TIFF, CALS OR PDF/A.

4. Press the Enter key to confirm the selection.

Type Photo Select Photo when the document contains a gray scale or color image, such as a photograph. When Photo is selected in the Scan Mode, the screen below will be displayed. The screen provides additional options for the user.

SCAN OPTIONS (PHOTO)

COMPRESSION:

FORMAT:

RAW

TIFF

PREVIEW

Scan Options (Photo) Screen

The SCAN OPTIONS (PHOTO) menu allows you to perform the following functions:

Enable or disable PREVIEW in Photo mode. When PREVIEW is enabled, a small JPEG (.JPG) file is created during the scanning process and stored on the hard disk. The FreeFlow Accxes Client Tools software, running on a network-connected terminal, can use this file to display a preview of the scanned image.

Specify the saved document compression format for Photo mode.

View the saved document file format for Photo mode. The format is 8 bit TIFF.

NOTE: This option will not be displayed unless the Scan-to-Net feature is enabled. To order this feature, contact your XEROX representative.

NOTE: The Background Suppression option cannot be used with the Photo setting. If Photo is selected, Background Suppression is automatically set to Off.

1. Enter the SCAN mode by pressing the Mode key, then entering the Directory Name and pressing the Enter key.

2. Select Photo by pressing the arrow key below Original, Type key. The screen shown below is displayed.

SCAN OPTIONS (PHOTO)

COMPRESSION:

FORMAT:

RAW

TIFF

PREVIEW

Scan Options (Photo) Screen

3. Press the Previous or Next key to highlight the scan option you wish to change.

4 Image Quality

52 Wide Format Copy System User Guide

Do one of the following:

For PREVIEW, press the Enter key to enable or disable the option. A checkmark appears in the box to the left of the option when the option is enabled. The factory default setting is enabled.

For COMPRESSION, press the Previous or Next key to highlight the desired setting. Then press the Enter key to select the highlighted format. The choices are RAW and PACKBITS. The factory default setting is RAW.

4. For FILE FORMAT, the only selection is TIFF. Repeat steps 3 and 4 to change the remaining setting, if desired.

5. Press the Enter key to confirm the selection.

6. Press the Exit key to return to the Ready screen.

Type, Color Color Select Color when scanning full color documents. When Color Type is selected, a version of the following screens will be displayed. The content of the screen will depend on the selected FORMAT and COMPRESSION. This screen will only be displayed in SCAN mode when the Scan-to-Net and Color Enablement feature keys are installed. The Normal and Photo LEDs will be lit when Color is selected.

To select the scan options for Color Mode:

1. Press the Mode key. The Please Enter Directory screen is displayed.

2. Enter the Directory Name. The READY TO SCAN INSERT DOCUMENT screen is displayed.

3. Select the Color by pressing the arrow key below the Original, Type key until the Normal and Photo lights come on. The SCAN OPTIONS (COLOR) screen is displayed.

4. Use the Enter key to enable/disable checkbox selection and the Next or Previous Key to select options with a colon (e.g., FORMAT: TIFF).

The options available for selections displayed on the screen will change depending on the FORMAT and COMPRESSION that are selected. Listed below are the selections and available options and their definition:

PREVIEW - Use this checkbox to enable or disable the generation of a preview image for your scanned document. Default is enabled (checkbox is checked)

FORMAT - Use this selection to determine which format you would like to have the scanned image saved in, TIFF, JPEG, or PDF/A. Default is TIFF.

COMPRESSION (TIFF selected) - Use this selection to determine the compression method to apply to the saved TIFF document. Select one of the following:

PACKBITS - Saves the document as 24-bit RGB compressed.

INDEX - Saves the document as 8-bit indexed RGB (using thresholding) compressed with PACKBITS.

INDEX ED - Saves the document as 8-bit indexed RGB (using error diffusion) compression with PACKBITS

4 Image Quality

Wide Format Copy System User Guide 53

SCAN OPTIONS (COLOR)

COMPRESSION:

FORMAT:

: PACKBITS

: TIFFPREVIEW

Scan Options (Color) Screens

SCAN OPTIONS (COLOR)

COMPRESSION:

FORMAT:

INDEX

: TIFF

PALETTE: DEFAULT

PREVIEW

Scan Options (Color) Screen TIFF file format PALETTE - Is shown only when the selected FORMAT is TIFF and the COMPRESSION is INDEX or INDEXED. Use this selection to determine which palette to use during RGB-to-index color conversion. Select one of the following:

DEFAULT - Is the standard Windows system palette.

CAD_GIS - Is an AutoCAD-based palette suitable for scanning CAD documents and GIS maps.

WEB - Is a Windows WEB palette of 216 colors suitable for publishing documents on the WEB.

PERCEPTUAL - Perceptual palette or Visual palette gives more weight to visually sensitive colors.

SCAN OPTIONS (COLOR)

COMPRESSION:

FORMAT:

NORMAL

JPEG PREVIEW

Scan Options (Color) Screen JPEG file format COMPRESSION (JPEG file format selected) - Use this selection to determine the compression method to apply to the saved JPEG document. Select one of the following:

BEST IQ - Saves a document at a lower compression ratio but has higher image quality.

NORMAL - Saves a document at an average compression ratio and has average image quality.

BEST COMPRESSION - Saves a document at a higher compression ratio but has a lower image quality

4 Image Quality

54 Wide Format Copy System User Guide

SCAN OPTIONS (COLOR)

COMPRESSION:

FORMAT:

NORMAL

PDF/A PREVIEW

Scan Options (Color) Screen PDF/A file format COMPRESSION (PDF/A file format selected) - Use this selection to determine the compression method to apply to the saved PDF/A document. Select one of the following:

BEST IQ - Saves a document at a lower compression ratio but has higher image quality.

NORMAL - Saves a document at an average compression ratio and has average image quality.

BEST COMPRESSION - Saves a document at a higher compression ratio but has a lower image quality

Background Suppression The Background Suppression enables you to make adjustments for documents that contain poor contrast between the foreground image and the background. Background Suppression monitors the pre-scan image, to ensure the best image quality possible. In the PRODUCTIVITY mode, there is no prescan, therefore Background Suppression is done while the document is being scanned.

NOTE: The scan system uses the first few inches of a document to determine the background suppression. If the first few inches of the document being scanned are not representative of the entire document, either too much or too little of the background will be removed. If this occurs, try physically turning the document 90 degrees and scan it again. Continue with this until an edge is found that produces a good scan.

Four choices are provided:

NOTE: Off is the only choice for Photo and Color Scanning. Scanning low contrast documents with background suppression OFF will produce washed out images. When scanning these documents, background suppression should be set to AUTO or DARK.

Off This setting disables Background Suppression. It produces a document that reproduces all the characteristics of the original document with minimum alteration. Choose this selection when:

The lead edge of the document is very different from the rest of the document (e.g., the lead edge contains a black border).

Maps with grayscale or color content may copy best in this mode.

To retain more light color information such as light gray or yellow.

(Light) This setting works best for documents on translucent or transparent media, such as vellum (tracing paper) or film, or with medium levels of colored background on opaque media

4 Image Quality

Wide Format Copy System User Guide 55

or for documents. Such documents have a higher contrast between the foreground and background than dark documents, but less contrast than normal documents.

(Dark) Use this setting for documents with a dark background or with medium contrast between the foreground and background. In this mode, the background is not suppressed, but the foreground image is improved to increase the contrast.

Auto (factory default) - The Scan System automatically adjusts the image quality parameters to obtain the best copy.

NOTE: All three Background Suppression settings can be adjusted further by changing the contrast setting in the Image Quality, Copy area.

Copy The Copy option allows you to darken or lighten the contrast of the copy with respect to the original document. Press the down arrow key to darken the contrast. Press the up arrow key to lighten the contrast. The indicator lamp for the selected contrast setting illuminates. The middle contrast setting is the factory default setting.

You can use this feature to further adjust the effects of the Type and Background Suppression selections. The feature operates with all four Background Suppression modes.

4 Image Quality

56 Wide Format Copy System User Guide

This page has been intentionally left blank.

Wide Format Copy System User Guide 57

5 Making Copies

Making copies When the Graphical Display indicates READY TO COPY, the Wide Format Copy System is ready to make copies.

Controlling the scan Several settings are available for controlling how the Scan System starts and finishes a scan. These settings are accessible from the SCANNER CONTROL option of the CONFIGURATION menu.

SCANNER CONTROL

DOCUMENT RETURN:

AUTOSCAN

MODE:

FRONT

AUTOWIDTH / AUTOCENTER

Scanner Control Screen

When making a copy, you need to be aware of these settings. If any of these settings have been changed from the default settings, the Scan System may not operate according to your expectations.

Below is a brief summary of the scan control settings. For complete information about these settings, refer to Scan System Control in the Main Menu section of this manual.

AUTOSCAN

AUTOSCAN enabled is the default setting. Normally, the AUTOSCAN mode is enabled. When it is enabled, the Scan System automatically begins the scanning of a document when the document is inserted. If AUTOSCAN is disabled, the Scan System transports the document to the starting position and then waits for you to press the Start key before beginning the scan.

DOCUMENT RETURN

FRONT is the default setting. When the DOCUMENT RETURN feature is set to FRONT, the Scan System returns the document to the front or READY position at the completion of the scan. When the DOCUMENT RETURN feature is set to REAR, the Scan System delivers the document to the rear Stacker at the completion of the scan.

5 Making Copies

58 Wide Format Copy System User Guide

Some documents will always exit to the rear at the completion of the scan regardless of the DOCUMENT RETURN setting. These documents include:

Thick documents

Documents longer than 5 feet (1.52 meters)

Documents over 36 inches (914 mm) in width

MODE:

MANUAL - The user must enter the width of the document manually, and very carefully center the document when inserting it into the Scan System. The document is prescanned in this mode.

AUTOWIDTH - This is the default setting. When AUTOWIDTH is selected, the Scan System automatically detects the width of the document.

AUTOWIDTH/AUTOCENTER - The document is prescanned in this mode.When AUTOWIDTH/AUTOCENTER is enabled, the Scan System automatically centers the image and automatically detects the document width. PRODUCTIVITY ANSI - PRODUCTIVITY is only available on Scan Systems with FreeFlow Accxes firmware 10.0 or higher, Scan System firmware 3.2.6 or higher, and the Productivity Document Feed Tray that includes discrete width sensors. PRODUCTIVITY ANSI is the default. Other media type selections include ARCH, ISO A, ISO B, JIS B and CUSTOM. These selections must be made so that the sensors detect the correct width. This feature eliminates the prescan width measurement, which increases document throughput speed resulting in greater productivity. CUSTOM requires standard media sizes to be entered in CUSTOM MEDIA FORMATS.

AUTOWIDTH and AUTOWITH/AUTOCENTER are not available in this mode.

Select the Menu key > CONFIGURATION>SCAN SYSTEM CONTROL, MODE: for additional information.

Image Quality The Image Quality area of the Scan System Control Panel allows you to make adjustments for both the type of original document and the output copy to produce the best possible image quality. It contains selections for Original (Document): Type and Background Suppression, and Copy options lighter or darker.

The illustration below depicts the Image Quality portion of the Control Panel. Refer to the Image Quality section of this manual for additional information.

5 Making Copies

Wide Format Copy System User Guide 59

Image Quality Illustration

There are many settings, other than Media Selection, Image Quality and Reduce/Enlarge areas, which are available on the Control Panel. The Transform special features key allows you adjust the margins around the image, specify the position of the image on the media, and transform the image into a mirror and/or inverted. Refer to the applicable sections of this guide for detailed information about the many document settings available to you.

Making a copy with the default settings When the default document settings are used, the display indicates that the roll of media that best fits the size of the original document will be automatically selected. The reduction/ enlargement setting is 100%, so the copy will be the same size as the original document. The copy quantity is set to 1.

The illustration below shows the READY screen in its default state.

READY TO COPY INSERT DOCUMENT

100.0% AUTO

1

Ready to Copy Screen

NOTE: Many document settings other than the default settings are possible. For example, the options keys on the Scan System Control Panel allow you to control the media selection, image quality and reduction/enlargement percentage. The Transform special features key allows you to adjust the margins around the image, specify the position of the image on the media, and transform the image into a mirror and/or inverted image. Refer to the applicable sections of this guide for detailed information about the many document settings available to you.

5 Making Copies

60 Wide Format Copy System User Guide

NOTE: When scanning to print, the copy is made using the current Printer processing defaults including margins. If the image being scanned is the same size as the media being used, set the margins to 0 (zero) to prevent the image from being clipped or select a larger media size.

To make a copy using the default document settings:

1. Insert the original document face down and centered on the Document Feed-in Tray of the Scan System.

NOTE: If the document is not exactly centered and the AUTOCENTER feature is enabled, the Scan System will automatically correct the problem electronically. The resulting image will still be correctly positioned on the output media. If AUTOWIDTH/AUTOCENTER is disabled, you will need to carefully center the document when inserting it. Refer to Controlling the scan on the previous page. AUTOWIDTH/AUTOCENTER is not available in the PRODUCTIVITY mode, requiring the user to manually align the document within the appropriate document size guidelines on the Feed-in Tray.

2. Gently move the document forward until the lead edge engages the feed rolls. The Scan System transports the document to the starting position. It then scans the document. The resulting image is electronically sent to the Printer and your copy is printed.

NOTE: If AUTOSCAN is disabled, you will need to press the Start key to begin the scan. Refer to Controlling the scan on the previous page.

NOTE: If the PRODUCTIVITY mode is enabled the document will start scanning immediately. If the PRODUCTIVITY mode is not enabled, the document will pre-scan a small distance then reverse itself before starting the complete scan.

3. When the document is returned to the READY position, do one of the following:

Pull the document to remove it. Lift the Thick Document Lever to remove fragile or thick documents.

Press the Start key on the Scan System Control Panel to scan the document again.

NOTE: If DOCUMENT RETURN is set to REAR, the document is delivered to the rear Stacker. Some documents exit to the rear Stacker regardless of the DOCUMENT RETURN setting. Refer to Controlling the scan on the previous page.

Making a copy the same size as the original document 1. Set the Media Selection Source to Auto. The Auto indicator lamp illuminates. This

setting allows the Wide Format Copy System to automatically select the available media roll that best fits the image width.

NOTE: If the correct media size is not loaded, the next larger size will be used.

2. Select the Media Selection, Type. The default setting is Bond.

3. Set the Media Selection, Output Format to Synchro. This setting cuts the media to the same length as the original document.

4. Set Reduce/Enlarge to Preset. If the size is not already set to 100%, use the Previous and Next keys to select a reduction and press the Enter key.

5 Making Copies

Wide Format Copy System User Guide 61

5. Insert the document face down into the Scan System. If the scan does not start automatically, press the Start key.

NOTE: To set the scan to begin automatically, refer to Scan System Control in the Main Menu section.

NOTE: If the image needs to be rotated to fit on the selected media size, additional processing time is required. If possible, feed the original image so that no image rotation is required. This will achieve the fastest processing time. For example, if an A-size copy is required on a 12-inch (30.48 cm) roll, feed the original with the short edge first, not the long edge first. If a B-size copy is required on a 17-inch roll, feed the document with the long edge first, not the short edge first.

The Scan System scans the document and the Printer (if not already busy) prints the copy immediately. If the Printer is busy when the scan is made, the copy will be printed when the Printer becomes available.

When the Scan System detects the trail edge of the document, the Printer automatically cuts the media so that the copy is the same length as the original document.

Fitting the image to a fixed copy size The scanned image can be automatically fit onto a predefined size of media.

1. Set the Media Selection, Source to Auto. The Auto indicator lamp illuminates. This setting automatically selects the available media roll that best fits the image width.

2. Select the Media Selection, Type of media. The default setting is Bond.

3. Set the Media Selection, Output Format to Preset and select the desired page size. This setting cuts the media to a previously defined length that the operator chooses.

PRESET OUTPUT FORMAT

SELECT 8.5 X 11 ANSI A

Preset Output Format Screen

4. Press the Previous or Next key until the desired output size is highlighted.

5. Press the Enter key to confirm your choice.

6. Set the Reduce/Enlarge to Auto.

7. Insert the document face down into the Scan System. If the scan does not start automatically, press the Start key.

NOTE: To set the scan to begin automatically, refer to Scan System Control in the Main Menu section of this manual.

The Scan System scans the document, and the Printer (if not already busy) prints the copy immediately. If the Printer is busy when the scan is made, the copy will be printed when the Printer becomes available.

5 Making Copies

62 Wide Format Copy System User Guide

This page has been intentionally left blank.

Wide Format Copy System User Guide 63

6 Scanning when using a Folder

Scanning when using a Folder When using a Folder, the document must be inserted in the correct orientation in order to have the title block visible after the copy is folded. Refer to the Finisher key information in the Special feature keys section of this manual for additional information to set up the desired fold and other Finisher options. Documents larger than 80 inches (2.1M) can only be partially folded.

When using the Reduce/Enlarge feature and a Folder, you must orient and insert the document title block in the same orientation as the resulting enlargement or reduction copy size. In addition, the recommended media should be used.

For example: the job requires that an A (A4) document be enlarged to a C (A2) document. To have the title block visible after folding, the A (A4) document must be inserted as if it were a C (A2) document.

You may want to refer to CUSTOM R/E PRESETS in the Main Menu, COPY OPTIONS section, and set up the REDUCTION/ENLARGEMENT default to show the standard reduction and enlargement. Set the reduction /enlargement to display A to C (A4 to A2) above the keys.

To ensure that the selected fold is made correctly, it is critical that the document be centered on the Scan System Document Feed Tray when scanning.

For additional folding and title block positioning information, refer to the Folder Operator Manual or the Folding Supplement CD.

6 Scanning when using a Folder

64 Wide Format Copy System User Guide

Ready to Copy Finisher Screen When the Finisher key is pressed and the finishing options are selected, a new page icon is added to the READY TO COPY screen. The page icon is displayed with a dotted box at one of the page corners. The dotted box indicates the title block location selection made using the Finisher menu. The title block location can be changed on this screen using the Next and Previous keys. Refer to the Finisher Key section for additional finishing information. The title block location icon will show a dotted line in all corners when a fold program other than BYPASS is selected.

READY TO COPY INSERT DOCUMENT

AUTO

1100.0 %

Ready to Copy Screen

NOTE: Any of the finishing options can be changed during a Sets Build job. The option(s) must be changed before the document to be copied is inserted.

Wide Format Copy System User Guide 65

7 Scanning Oversized Documents

Scanning Oversized Documents An oversized document is defined as any document that is larger in width or length than a standard E-size (A0) document.

Long Documents Operator assistance will be required to guide and control the position of a long document to prevent it from skewing or moving from side-to-side as it feeds through the Scan System. Documents longer than 36 inches (914 mm) will always exit to the rear of the Scan System.

See the Maximum Copy Length section in this document.

Wide Documents Documents wider than 36 inches (914 mm), but less than 42 inches (1057 mm), can be scanned. However, the scanned image area, of a document centered on the Feed-in Tray, is 36 inches (914 mm). Any image beyond the 36-inch (914 mm) width will be clipped off on the output copy.

When a document wider than 36 inches (914 mm) is inserted into the Document Handler, a message will be displayed to enter the scan width. To scan the document, enter 36 in. (914 mm) then press the Enter key to start the scan. A number larger than 36 (914) will not be accepted.

7 Scanning Oversized Documents

66 Wide Format Copy System User Guide

This page has been intentionally left blank.

Wide Format Copy System User Guide 67

8 Special Features Keys

Special features keys There are many enhanced features for making copies that meet special needs. The keys that control these features are on the right side of the Scan System Control Panel.

To enable a feature, press the applicable key. If the feature has an associated screen, that screen is displayed when the key is pressed. If any settings are changed from the default state, the corresponding indicator lamp next to the key illuminates. Pressing the C/CA key on the numeric keypad twice returns all settings for the feature to the default state and the corresponding indicator lamp is extinguished.

When the settings for a feature are appropriately set, pressing the same feature key causes the changes to be accepted and the system returns to the READY state. Pressing a different feature key while editing a setting is invalid and causes a beep. Pressing a different feature key while not editing a setting causes the requested feature screen to be displayed.

If a feature has no associated screen, pressing that feature key switches the feature on (enabled) or off (disabled). When such a feature is enabled, the corresponding indicator lamp is illuminated.

If the BEEP function (factory default) is enabled, a beep sound will be heard when a key is pressed. If an improper key is pressed, a multiple beep sound will be heard.

The illustration on the following page depicts the special features portion of the Scan System Control Panel.

8 Special Feature Keys

68 Wide Format Copy System User Guide

Stop Start

1

Transform Sample

Printer Interrupt

Store/ Recall

Batch

Sets Build

Finisher

A B C

4 5 6

7 8 9

3

0 C/CA/.

2 D E F

G H I J K L M N O

P R S T U V W X Y

Numeric Keys Area

Printer Interrupt Key Jobs on the Wide Format Copy System have the following priority:

1. Any job currently printing

2. A copy job that is ready to print

3. A remote print job.

If a remote print job is in progress, a copy job (one or more images captured by the Scan System) cannot normally use the Printer until the remote print job has finished. The Printer Interrupt key enables you to switch the copy priority from normal to high.

To process a copy job immediately, press the Printer Interrupt key. The Printer Interrupt indicator lamp illuminates. The current pages of the most current remote print job are completed. Usually a maximum of two pages are printed. The print job is then suspended and you can run copy jobs. When the copy jobs are finished, you can press the Printer Interrupt key again. The Printer Interrupt indicator lamp is extinguished. The interrupted remote print job resumes.

If you send no more copy jobs, press no keys, and scan no documents, the Printer Interrupt feature is automatically disabled after a time set by the PRINTER INTERRUPT timer. Refer to "Timers" in the "Main Menu, CONFIGURATION" section for instructions about how to set this value. The default value is 1 minute. It can be set to a value between 1 and 99 minutes.

8 Special Feature Keys

Wide Format Copy System User Guide 69

Store/Recall Key The Store/Recall feature contains the following menu choices:

LAST JOB - Enables you to recall and reuse the information from the last copy job.

JOB TEMPLATES - Enables you to save the settings from previous jobs in memory as templates.

SAVE DEFAULT TEMPLATE - Enables you to save the settings from the current job as the default template.

RECALL FACTORY DEFAULTS - Enables you to recall the factory default settings as the active default settings.

To access the STORE/RECALL menu:

1. Press the Store/Recall key. The STORE/RECALL menu screen is displayed. The black arrows indicate that the menu contains more options than are visible. The selected option is highlighted.

STORE/RECALL LAST JOB JOB TEMPLATES SAVE DEFAULT TEMPLATE

Store/Recall Screen

2. Press the Previous or Next key to scroll through the list of options.

3. When the desired option is highlighted, press the Enter key to select the option. The menu or screen for the selected option is displayed.

Last Job The LAST JOB option of the STORE/RECALL menu provides a sub-menu of the following choices:

RECALL LAST JOB Enables you to recall and reuse the parameters, images, and features associated with the last copy job. You can either reprint the last job or print a new job using all of the recalled settings. If you desired, the recalled settings could be changed without scanning the job again.

NOTE: When Immediate Image Overwrite is enabled and running on the Web Printer Management Tool, all the scanned images and image sets will be deleted from FreeFlow Accxes as soon as they are processed. The FreeFlow Accxes controller will reboot, causing a DISK IMAGE OVERWRITE IN PROGRESS message on the printer and scan system during the reboot. Scan System users will not be able to recall the last job.

DELETE LAST JOB Enables you to delete the information from the last job.

NOTE: In the SCAN mode, the Last Job option is not available.

To access the LAST JOB menu:

1. Press the Store/Recall key. The STORE/RECALL menu screen is displayed.

8 Special Feature Keys

70 Wide Format Copy System User Guide

2. Press the Enter key to select LAST JOB. The LAST JOB menu screen is displayed. The selected option is highlighted.

LAST JOB RECALL LAST JOB DELETE LAST JOB

Last Job Screen

3. Press the Previous or Next key to highlight the desired option.

4. Press the Enter key to select the highlighted option. The screen for the selected option is displayed.

Recalling the Last Job Use the RECALL LAST JOB option to recall the information from the last job.

NOTE: If the Invert feature (changes dark to light and vice versa) is selected before printing the recalled document, the document will not be inverted. It will need to be rescanned to get the inverted image.

To recall the last job information:

1. Press the Store/Recall key. The Store/Recall menu screen is displayed.

2. Press the Enter key to select LAST JOB. The LAST JOB menu screen is displayed.

3. Press the Enter key to select RECALL LAST JOB. The screen shown below is displayed.

COPIER PARAMETERS AND IMAGES FOR LAST JOB RECALLED

PRESS ENTER TO CONTINUE

Copier Parameters and Images Screen

4. Press the Enter key to return to the READY screen.

You can now use the settings as they have been recalled, or you can change one or more of them.

Reprinting with Changed Features If the last job was a set, the settings that can be changed are displayed in a neutral state (the LEDs are off). Changing one of these settings will apply to all of the pages in the set. Some of the settings that can be changed are: scale, page size, media type, margins, and justification.

NOTE: The recalled job must be printed or cleared before the next document can be scanned. If there is no last job to be restored, as is the case at power up or after the last job has been deleted, a warning message will advise you.

8 Special Feature Keys

Wide Format Copy System User Guide 71

Deleting the Last Job If, for security reasons, the parameters and images of the last job should not be left stored, use the DELETE LAST JOB option.

To delete the information from the last job:

1. Press the Store/Recall key. The STORE/RECALL menu screen is displayed.

2. Press the Enter key to select LAST JOB. The LAST JOB menu screen is displayed.

3. Press the Next key to highlight DELETE LAST JOB.

4. Press the Enter key to select DELETE LAST JOB. A delete confirmation screen is displayed. The default response is NO.

DELETE LAST JOB ARE YOU SURE ?: NO

Delete Last Job Screen

5. Press the Previous or Next key to change the response to YES.

6. Press the Enter key to confirm the deletion. The screen shown below is displayed. The last job images and parameters are deleted.

LAST JOB PARAMETERS AND IMAGES ARE NOT AVAILABLE

PRESS ENTER TO CONTINUE

Job Parameters and Images Screen

7. Press the Enter key to return to the READY screen.

Job Templates The JOB TEMPLATES option of the STORE/RECALL menu provides a sub-menu of the following choices:

RECALL TEMPLATE - Enables you to recall saved settings.

SAVE TEMPLATE - Enables you to save job settings in memory.

DELETE TEMPLATE - Enables you to delete saved settings.

To access the JOB TEMPLATES menu:

1. Press the Store/Recall key. The STORE/RECALL menu screen is displayed.

2. Press the Next key to highlight JOB TEMPLATES.

3. Press the Enter key to select JOB TEMPLATES. The JOB TEMPLATES menu screen is displayed. The selected option is highlighted.

8 Special Feature Keys

72 Wide Format Copy System User Guide

JOB TEMPLATES RECALL TEMPLATE SAVE TEMPLATE DELETE TEMPLATE

Job Templates Screen

4. Press the Previous or Next key to highlight the desired option.

5. Press the Enter key to select the highlighted option. The screen for the selected option is displayed.

Saving Job Templates The SAVE TEMPLATE option allows you to save groups of settings associated with a job in memory as templates. Up to nine such templates can be saved.

To save a job template:

1. Press the Store/Recall key. The STORE/RECALL menu screen is displayed.

2. Press the Next key to highlight JOB TEMPLATES.

3. Press the Enter key to select JOB TEMPLATES. The JOB TEMPLATES menu screen is displayed.

4. Press the Next key to highlight SAVE TEMPLATE.

5. Press the Enter key to select SAVE TEMPLATE. The SAVE TEMPLATE screen is displayed. It shows the unused template locations. Locations that contain a template already are not shown.

SAVE TEMPLATE UNUSED TEMPLATES: 6 7 8 9 ENTER TEMPLATE NUMBER: 0

Save Template Screen

6. Choose an unused location and use the numeric keypad to enter its location.

7. Press the Enter key to confirm your location choice. The settings from the current copy job are saved at the location entered and a save confirmation screen is displayed.

JOB PARAMETERS SAVED

PRESS ENTER TO CONTINUE

Job Parameters Saved Screen

8 Special Feature Keys

Wide Format Copy System User Guide 73

NOTE: You can replace the contents of a used location with the current job settings information. If you choose a location that already contains information, the TEMPLATE IS IN USE screen is displayed as shown below. Press the Enter key to overwrite the contents. Press the Exit key to cancel the operation.

TEMPLATE IS IN USE

PRESS ENTER TO OVERWRITE

EXIT TO ABORT

Template is in Use Screen

8. Press the Enter key to return to the READY screen.

Recalling Job Templates The RECALL TEMPLATE option allows you to recall job parameters that were previously saved as templates and use them for the current job.

To recall a template:

1. Press the Store/ Recall key. The STORE/RECALL menu screen is displayed.

2. Press the Next key to highlight JOB TEMPLATES.

3. Press the Enter key to select JOB TEMPLATES. The JOB TEMPLATES menu screen is displayed.

4. Press the Enter key to select RECALL TEMPLATE. The RECALL TEMPLATE screen is displayed. The storage locations that actually contain templates are shown. Locations that do not contain a template are not shown.

RECALL TEMPLATE TEMPLATES IN USE: 1 2 3 4 5 ENTER TEMPLATE NUMBER 0

Recall Template Screen

5. Use the numeric keypad to enter the location of the template to be recalled.

6. Press the Enter key to confirm your choice. A recall confirmation screen is displayed. The associated template is recalled and the Scan System Control Panel settings are configured accordingly.

JOB PARAMETERS RECALLED

PRESS ENTER TO CONTINUE

Job Parameters Recalled Screen

8 Special Feature Keys

74 Wide Format Copy System User Guide

You can now use the parameter settings as they have been recalled, or you may change some of them.

NOTE: If you change any of the Image Quality settings (i.e., document type, background suppression, or copy contrast) or if you want to invert the image, an error message will advise you to rescan the image. You must rescan the image to change any image quality settings for a job that has been recalled.

7. Press the Enter key to return to the READY screen.

Deleting Job Templates Use the DELETE TEMPLATE option to delete previously saved templates. Doing so leaves the template location blank and available to use again. Once a template has been deleted, it cannot be recalled.

To delete a saved template:

1. Press the Store/Recall key. The STORE/RECALL menu screen is displayed.

2. Press the Next key to highlight JOB TEMPLATES.

3. Press the Enter key to select JOB TEMPLATES. The JOB TEMPLATES menu screen is displayed.

4. Press the Next key until DELETE TEMPLATE is highlighted.

5. Press the Enter key to select DELETE TEMPLATE. The DELETE TEMPLATE screen is displayed. This screen indicates the locations for the templates currently in use. Locations that do not contain a template are not shown.

Below is an example of the DELETE TEMPLATE screen.

DELETE TEMPLATE TEMPLATES IN USE: 1 2 3 4 5 ENTER TEMPLATE NUMBER: 0

Delete Template Screen

6. Use the numeric keypad to enter the location of the template to be deleted, and then press the Enter key. The deleted location is removed from the list in the DELETE TEMPLATE screen and the contents of that location are deleted.

You can now select other locations to be deleted in the same way.

7. If no more locations are to be deleted, press the Exit key to return to the READY screen.

Save Default Template The SAVE DEFAULT TEMPLATE option of the STORE/RECALL menu enables you to save the settings for the current job as the default settings. Each additional job will then have these settings established as the default selections.

To save the current job settings as the default template:

1. Ensure that all the options under Media Selection, Image Quality, and Reduce/Enlarge are set as desired. Make any necessary changes.

2. Press the Store/Recall key. The STORE/RECALL menu screen is displayed.

8 Special Feature Keys

Wide Format Copy System User Guide 75

3. Press the Next key until SAVE DEFAULT TEMPLATE is highlighted.

4. Press the Enter key to select SAVE DEFAULT TEMPLATE. A confirmation screen is displayed indicating that the job parameters have been saved.

JOB PARAMETERS SAVED

PRESS ENTER TO CONTINUE

Job Parameters Saved Option

5. Press the Enter key to return to the READY screen.

Recall Factory Defaults The factory default job settings are permanently stored in memory. The RECALL FACTORY DEFAULTS option of the STORE/RECALL menu enables you to recall the factory default settings as the active default settings.

To recall the factory default settings:

1. Press the Store/Recall key. The STORE/RECALL menu screen is displayed.

2. Press the Next key until RECALL FACTORY DEFAULTS is highlighted.

3. Press the Enter key to select RECALL FACTORY DEFAULTS. The factory default settings are immediately recalled. A confirmation screen is displayed.

JOB PARAMETERS RECALLED

PRESS ENTER TO CONTINUE

Job Parameters Recalled Screen

4. Press the Enter key to return to the READY screen.

Finisher key A finishing device, such as a folder, can be connected to the Wide Format Copy System. If such a device is connected, the Finisher key enables or disables that device.

To enable/disable a finishing device:

Press the Finisher key. The Finisher indicator lamp illuminates and the FINISHER menu screen is displayed. The black arrows indicate that the menu contains more options than are visible. The selected option is highlighted.

8 Special Feature Keys

76 Wide Format Copy System User Guide

FINISHER FOLD PROGRAM TITLE BLOCK LOCATION OUTPUT BIN OVERLENGTH OPTION TAB OPTIONS

Finisher Screen

Other Finisher options that are accessed from this screen, using the Next key, are: Punch Options, Margin Options, Crossfold Options, and Intelligent Title Block Option.

NOTE: If no finishing device is connected, pressing the Finisher key produces the error message shown below.

FINISHER FINISHER OPTION IS NOT AVAILABLE

Finisher Not Available Error Message Screen

When a set is being built, the finisher options cannot be changed and pressing the Finisher key is invalid. The error screen shown below is displayed. Enable the finisher and select the finisher options either before selecting the Sets Build option or after the set has been built.

FINISHER FINISHER OPTION CANNOT BE CHANGED DURING SETS BUILD OPERATION

1. Press the Exit key to return to the READY screen. The Finisher indicator lamp is

extinguished.

2. Press the Previous or Next key to scroll through the list of options.

3. When the desired option is highlighted, press the Enter key to select the option. The screen for the selected option is displayed. See Finisher menu options below and on the next page for an illustration and description of each option. Also refer to the Folder User Documentation for additional information on the available folding options.

4. Press the Previous or Next key to scroll through the choices for the selected option.

5. When the desired choice is highlighted, press the Enter key to confirm your selection.

6. Repeat steps 4 and 5 if you want to change a setting for any other options.

7. Press the Exit key to return to the READY screen.

8 Special Feature Keys

Wide Format Copy System User Guide 77

A page icon is displayed with a dotted box at one of the page corners if a FOLD PROGRAM other than BYPASS is selected. The dotted box indicates the title block location selection made using the Finisher menu. The title block location can be changed on this screen using the Next and Previous keys.

READY TO COPY INSERT DOCUMENT

AUTO

1100.0 %

Ready to Copy Screen 1. To disable the finisher, press the Finisher key again and select BYPASS on the

FOLD PROGRAM screen. The Finisher indicator lamp is extinguished.

Finisher menu options Below are descriptions of each of the Finisher menu options. Refer to the Finisher user documentation for additional information on these options.

Fold Programs The FOLD PROGRAM feature enables you to select one of up to 20 user-defined programs. The program names are programmed into the finisher and passed to the Controller when the finisher goes through its power-up sequence.

FOLD PROGRAM PROGRAM: USER PROGRAM

Fold Program Screen

Overlength Options The OVERLENGTH OPTIONS feature enables you to specify how long documents (documents over 80 inches long) are handled by the folder. The choices are NO FOLD and Z-FOLD. If NO FOLD is selected, the long document will not be folded. If Z-FOLD is selected, the long document will be Z-FOLDED, but not cross-folded. NO FOLD is the factory default setting. This is not available for all finishers.

OVERLENGTH OPTIONS OVERLENGTH: NO FOLD

Overlength Options Screen

8 Special Feature Keys

78 Wide Format Copy System User Guide

Tab Options The TAB OPTIONS feature enables you to override the pre-programmed tab settings for the selected finishing program. The choices are ALWAYS ON, ALWAYS OFF, and USE PROGRAM SETTING. USE PROGRAM SETTING is the factory default setting.

TAB OPTIONS TAB: USE PROGRAM

Tab Options Screen

Punch Options The PUNCH OPTIONS feature enables you to override the pre-programmed hole punch settings for the selected finishing program. The choices are ALWAYS ON, ALWAYS OFF, and USE PROGRAM SETTING. USE PROGRAM SETTING is the factory default setting.

PUNCH OPTIONS PUNCH: USE PROGRAM

Punch Options Screen

Margin Options The MARGIN OPTIONS feature enables you to override the pre-programmed margin settings for the selected finishing program. The choices are ALWAYS OFF and USE PROGRAM SETTING. Note that ALWAYS ON is not an available setting. USE PROGRAM SETTING is the factory default setting.

MARGIN OPTIONS MARGIN: USE PROGRAM

Margin Options Screen

NOTE: When using the Scan Systems width detection sensors, if the document is a little bit off- center, this could cause problems for folding, especially for A, B, and C size documents. When using the sensors to detect the width of your document, you must center the document as you feed it into the Scan System.

8 Special Feature Keys

Wide Format Copy System User Guide 79

Crossfold Options The CROSSFOLD OPTIONS feature enables you to override the pre-programmed crossfold settings for the selected finishing program. The choices are ALWAYS ON, ALWAYS OFF, and USE PROGRAM SETTING. USE PROGRAM SETTING is the factory default setting.

CROSSFOLD OPTIONS CROSSFOLD: USE PROGRAM

Crossfold Options Screen

Title Block Location The TITLE BLOCK LOCATION feature enables you to specify the location of the title block for the copy jobs that are about to be run. On the Scan System, select the Finisher Key > Intelligent Title Block to get to the following screen. The title block location choices are BOTTOM RIGHT, BOTTOM LEFT, TOP RIGHT, and TOP LEFT. BOTTOM RIGHT is the factory default setting.

INTELLIGENT TITLE BLOCK OPTION

INTELLIGENT TITLE BLOCK

Intelligent Title Block Screen

INTELLIGENT TITLE BLOCK should be used if the title block is not located in the desired location on the folded copy. This selection will use information, document size, selected fold program, and title block position input to place the title block in a position based on the information. Intelligent Title Block is DISABLED by default. It may not be the users desired location. Before making this selection, check the following:

AUTO ROTATE IS SELECTED. DOCUMENT BEING SCANNED IS ORIENTED CORRECTLY FOR SCANNING. ENSURE THAT THE TITLE BLOCK POSITION SPECIFIED IS CORRECT. FOR ADDITIONAL HELP, REFER TO THE FOLDING SUPPLEMENT MANUAL.

NOTE: The title block location may also be selected on the READY TO COPY screen, using the title block location icon. The title block location is indicated by the dotted lines.

TITLE BLOCK

TB LOCATION: UPPER RIGHT

Title Block Location Screen

8 Special Feature Keys

80 Wide Format Copy System User Guide

Output Bin The OUTPUT BIN feature enables you to specify which finisher output bin to use for the finished output. The choices are DONT CARE, BIN X (where X equals 1 to the actual number of finisher bins), and FANFOLD. DONT CARE is the factory default setting. The settings are dependent on the finisher.

OUTPUT BIN

OUTPUT BIN: BYPASS

Output Bin Screen

Sets Build Key The Sets Build mode allows you to scan a series of images and build an electronically collated set. Once the set is built, one or more collated copies can be printed.

NOTE: The Sets Build mode is not available unless the Wide Format Copy System is in the COPY mode.

NOTE: Any of the finishing options can be changed during a Sets Build job. The option(s) must be changed before the document to be copied is inserted.

Preparing to Build the Set In Sets Build mode, documents of C (A2) size, and larger, are normally delivered to the rear of the Scan System after the scan. If the DOCUMENT RETURN parameter is set to REAR, then all documents are delivered to the rear after scanning. The Wide Format Scan System is equipped with a document catching device, called the Stacker, to receive these documents. Refer to Scan System Control in the Main Menu section of this manual for further information about the DOCUMENT RETURN parameter.

Building and Printing the Set To build a collated set:

1. Press the Sets Build key. The Sets Build indicator lamp illuminates and the SETS BUILD screen is displayed. This screen enables you to select the desired collation method, to select whether or not to print checkplots, and to begin the accumulation of the documents to create the set.

SETS BUILD

COLLATION: FORWARD

CHECKPLOT

Sets Build Screen 2. Press the Previous or the Next key to select FORWARD or REVERSE collation.

8 Special Feature Keys

Wide Format Copy System User Guide 81

FORWARD prints the collated set in the order that the sheets were scanned. Page 1 will be on the top.

PRINTED

123

SCANNED

123

REVERSE prints the set in the reverse order that they were scanned. Page 1 will be

on the bottom.

123 SCANNED

321 PRINTED

3. Regardless of the collation order chosen, if you want a printed copy (checkplot) after you scan each document, before they are printed as a set, then select the CHECKPLOT box.

4. Press the Enter key to confirm your choice. The READY TO BUILD SET screen is displayed.

READY TO BUILD SET INSERT DOCUMENT: 1

MEMORY100.0 %

AUTO

Ready to Build Set Screen

5. Insert each document of the set, one at a time, into the Scan System as prompted by the display. As the documents are scanned, the amount of memory used is shown in the rectangular graphical display.

NOTE: You can select reduction/enlargement and copy quality settings for each sheet prior to scanning that sheet.

6. When the set is completely scanned, press the Sets Build key again. The Sets Build indicator lamp is extinguished when the Start key is pressed then the READY TO PRINT SET screen is displayed.

READY TO PRINT SET PRESS START TO PRINT

100.0 3

Ready to Print Set Screen

7. If desired, you can now make further changes to the Media Selection, Source selection and the Reduction/Enlargement value. Any such change will be applied to that printing of the entire set.

8. Enter the number of copies desired and press the Start key. The Printer prints the number of sets requested.

8 Special Feature Keys

82 Wide Format Copy System User Guide

After the printing of the set, the set can be recalled, the values changed again, and the set reprinted using the new values. To recall the set, refer to Store/Recall key in the Special features key section of this manual for further information.

NOTE: Settings for the last document scanned are not restored when recalling a set. After a set is recalled, all LEDs will be turned off. If a setting is changed after a set is recalled, it will be applied to all documents in the set.

Batch Key The Batch feature allows you to improve copy speed by enabling Batch Mode processing of several documents on the Scan System. When Batch Mode processing is enabled, the Scan System collects prescan information for just the first document inserted into the Scan System. Prescan information on subsequent documents in the set is not collected. The subsequent documents will be scanned using the information collected on the first document. Eliminating the collection of this information increases overall copy speed.

To enable Batch Mode processing:

1. Press the Batch key. The Batch indicator lamp will begin flashing.

2. Insert the first original into the Scan System. The Scan System scans the original and the screen shown below is displayed.

WIDTH FOUND FOR SET IS XX.X

INPUT ANOTHER WIDTH OR PRESS ENTER TO ACCEPT

Width Found for Set is XX.X Screen

3. Do one of the following:

Use the numeric keypad to enter the width of the set and press the Enter key to accept the value.

Press the Enter key to accept the width detected by the Wide Format Copy System.

The Batch indicator lamp becomes steady and remains so until batch mode is disabled.

4. When the last document in the set has been scanned, press the Batch key to disable batch mode. The Batch indicator lamp is extinguished.

NOTE: When Batch mode is ENABLED, the AUTOCENTER feature is temporarily disabled. Be careful to manually center each document that is inserted into the Scan System

8 Special Feature Keys

Wide Format Copy System User Guide 83

Transform Key The Transform feature contains the following menu choices:

MARGINS - Allows you to adjust the dimensions of the margins around the image. By entering positive margins, blank space is inserted around the image. By entering negative values, unwanted parts of the image can be cropped.

JUSTIFICATION - Allows you to adjust the position of the image on the media.

TRANSFORM - Allows you to request transformation of the scanned image into a mirror image, a negative photographic inversion, or both.

SINGLE BIT SCALE MODE Allows you to select from Fast, Best and Line Optimized.

NOTE: The image can also be rotated. Refer to Imaging in the Copy Options section for further information about image rotation.

To access the TRANSFORM MENU:

1. Press the Transform key. The TRANSFORM MENU screen is displayed. The selected option is highlighted.

TRANSFORM MENU MARGINS JUSTIFICATION TRANSFORM

Transform Menu Screen

2. Press the Previous or Next key to highlight the desired option.

3. Press the Enter key to select the highlighted option. The screen for the selected option is displayed.

Margins The MARGINS option of the TRANSFORM MENU allows you to select the dimensions for the margins that surround an image. These margins are referred to as the lead, left, right and trail edges.

NOTE: Margins can only be adjusted when the Wide Format Copy System is in the COPY mode.

The example below illustrates an image entering the Scan System and the orientation of the image margins.

Scanner

Left image d

Right image d

Trail d

Lead d

8 Special Feature Keys

84 Wide Format Copy System User Guide

Image Entering the Scan System Diagram Margins are added to the image in one of two ways:

If Synchro has been selected from the Output Format area of the Scan System Control Panel, the lead margin is added before the image is printed. The trail margin is added after the media cut signal is received from the Scan System. Thus, the length of the media from the Printer will be the scanned document length plus the lead and trail margins.

If a fixed media length (Preset or Manual) has been selected as the Output Format, the white space of the specified margin surrounds the image, but the actual physical dimensions of the media remain as specified. The margins reduce the allowable area on the media in which the image may be placed.

To adjust the margins for an image:

1. Press the Transform key. The TRANSFORM MENU screen is displayed.

2. Press the Enter key to select MARGINS. A screen displaying the settings for each margin is displayed. Below is an example of the screen.

LEAD + 1.0 IN LEFT + 0.0 IN RIGHT + 0.0 IN TRAIL + 0.0 IN

Margins Selection Screen in Transform Menu

If the unit of measure has been set to inches, IN appears next to each value. If the unit of measure has been set to millimeters, MM appears next to each value. Refer to Localization in the Main CONFIGURATION section for information about setting the display units.

The graphical display to the right of the margin settings illustrates the approximate placement of the image as a result of the settings.

3. Press the Previous or Next key to highlight the setting you wish to change.

NOTE: Each margin has two components: a +/- indicator and a numeric value. As you press the Previous or Next key, the components highlight individually.

4. Press the Enter key to select the setting.

5. Change the setting as follows:

To change the + or - setting, press the Previous or Next key. An edge of the image can be clipped by entering a negative margin value for that edge. In that case, the affected edge is shown as a dotted line and the image icon is shown as partially outside the bounds of the media.

The illustration below shows a negative left margin with TOP LEFT justification.

8 Special Feature Keys

Wide Format Copy System User Guide 85

LEAD + 2.0 IN LEFT - 1.0 IN RIGHT + 0.0 IN TRAIL + 0.0 IN

Margins Selection Screen in Transform Menu

To change the value setting, use the numeric keypad to enter the value. The values can be set in increments of 0.1 in (1.0 mm) and over a range of +8 to -8 in (+203 to - 203 mm). Values outside the allowed range are rejected. If you enter an invalid value, press the Exit key to clear it. The default margins are 0.

6. Press the Enter key to confirm the setting. The graphical display updates accordingly.

NOTE: To cancel the setting, press the Exit key.

7. When you have set all the margins as desired, press the Exit key to return to the TRANSFORM MENU screen.

Justification The JUSTIFICATION option of the TRANSFORM MENU allows you to adjust the position of the image on the media.

NOTE: Image means the entire scanned page including the white space.

To specify the image position:

1. Press the Transform key. The TRANSFORM MENU screen is displayed.

2. Press the Next key to highlight JUSTIFICATION.

3. Press the Enter key to select JUSTIFICATION. The JUSTIFICATION screen is displayed. This screen shows the current settings for the X and Y coordinates. It also includes a graphical display of the approximate position of the image as a result of the settings.

Below is an example of the JUSTIFICATION screen.

JUSTIFICATION X: LEFT Y: CENTER

Justification Screen

4. Press the Previous or the Next key to select the X (horizontal) or Y (vertical) coordinate.

5. Press the Enter key to confirm your choice.

6. Press the Previous or Next key to select a choice for justification.

8 Special Feature Keys

86 Wide Format Copy System User Guide

For the X direction, the choices are LEFT, CENTER, and RIGHT. For the Y direction, the choices are TOP, CENTER, and BOTTOM.

7. Press the Enter key to confirm your choice. The graphical display updates accordingly.

NOTE: To cancel your choice, press the Exit key.

8. Repeat steps 4 through 7 if you wish to change position of the other coordinate.

9. Press the Exit key to return to the TRANSFORM MENU screen.

Transform The TRANSFORM option of the TRANSFORM MENU allows you to create a mirror image of a scanned image and to convert a scanned image to a negative image.

Creating a Mirror Image The MIRROR option allows you to create a mirror image of a scanned image.

To create a mirror image:

1. Press the Transform key. The TRANSFORM MENU screen is displayed.

2. Press the Next key until TRANSFORM is highlighted.

3. Press the Enter key to select TRANSFORM. The TRANSFORM screen is displayed.

Below is an example of the TRANSFORM screen with both the MIRROR and INVERT options turned off.

TRANSFORM MIRROR: OFF

INVERT: OFF

Transform Screen

4. Press the Enter key to select MIRROR.

5. Press the Previous or Next key to select the desired transformation. Four choices are available: X, Y, XY, and OFF. Table 4 below graphically depicts the choices.

Axis Transform

X

Y

XY

OFF

8 Special Feature Keys

Wide Format Copy System User Guide 87

6. Press the Enter key to confirm your choice. The graphical display updates accordingly. The illustration below shows the TRANSFORM screen with X as the mirror image selection.

TRANSFORM MIRROR: X INVERT: OFF

Transform Screen

NOTE: To cancel your choice, press the Exit key.

7. Press the Exit key to return to the READY screen.

Inverting an Image The INVERT option allows you to convert a scanned image to a negative image. For black and white images, the white pixels will be printed black and the black pixels will be printed white. For grayscale images, the image will be converted into its photographic negative. INVERT is not selectable when Color is selected as an Original Type.

To invert an image:

1. Press the Transform key. The TRANSFORM MENU screen is displayed.

2. Press the Next key until TRANSFORM is highlighted.

3. Press the Enter key to select TRANSFORM. The TRANSFORM screen is displayed.

Below is an example of the TRANSFORM screen with both the MIRROR and INVERT options turned off.

TRANSFORM MIRROR: OFF

INVERT: OFF

Transform Screen

4. Press the Next key to highlight INVERT.

5. Press the Enter key to select INVERT.

6. Press the Previous or Next key to turn the option ON or OFF.

7. Press the Enter key to confirm your choice. The graphical display updates accordingly.

8 Special Feature Keys

88 Wide Format Copy System User Guide

When INVERT is ON, the icon on the right side of the TRANSFORM screen is inverted. The example below shows the TRANSFORM screen with INVERT turned ON.

TRANSFORM MIRROR OFF INVERT ON

Transform Screen

NOTE: To cancel your choice, press the Exit key.

8. Press the Exit key to return to the READY screen.

Sample key The Sample key allows you to access the Sample Mode screen, from where you can send a scanned image to an FTP destination.

The Sample key also allows you to print a sample of a scanned image in both the COPY mode and the SCAN mode. You can then check the sample for quality or observe the results of features or copy quality adjustments before the document is copied or scan to a file.

The dimensions of the sample, in the Copy mode, are the width of the page by 210 mm. The sample is taken from a point equidistant from the lead and trail edge of the image. Refer to Copy Mode below for instruction to print a sample.

In the SCAN mode the sample size is the whole document. To enable the Sample key in the SCAN Mode, the Scan-to-net feature must be installed. To enable a print sample the Scan-to- Print feature key must be installed. Refer to the Scan Mode Sample below for instructions to print a sample.

Copy Mode Sample To print a sample of a scanned image:

1. Press the Sample key. The Sample indicator lamp illuminates. The Scan System Control Panel is placed in Printer Interrupt mode and the Printer Interrupt indicator lamp illuminates. The Printer immediately prints a sample of the next image inserted into the Scan System. The SAMPLE MODE screen is displayed.

SAMPLE MODE

PRESS START TO ACCEPT PAGE. PRESS C/CA TO REJECT.

Sample Mode Screen 1

2. Do one of the following:

Press the Start key to print the complete image as a full-size copy.

Press the C/CA key to delete the scanned image.

8 Special Feature Keys

Wide Format Copy System User Guide 89

3. Press the Sample key again to disable the Sample feature. The Printer is returned to the default priority setting and the Sample and Printer Interrupt indicator lamps are extinguished.

Scan Mode Sample The best sample prints will be produced if the image enhancement features have been enabled. Refer to the Image Quality section of this document for more information.

In order to have the selections indicated below in the SAMPLE MODE screen, the Scan-to-Net feature key must be installed to get SCAN IMAGE TO FILE, and the Scan-to-Print feature key must be installed to get SCAN IMAGE TO PRINTER. It is convenient on the Wide Format Copy Systems to be able to make a sample before scanning an image to file.

To print a sample copy, perform the following:

1. If the Scan System is set to COPY mode, switch to SCAN mode. For more information, refer to the section of this document entitled Switching between COPY and SCAN mode.

2. Enter the Directory name.

3. Press the Sample special function key. The SAMPLE MODE screen is displayed.

SAMPLE MODE

FILE: LOCAL FILE

SCAN IMAGE TO PRINTER

Sample Mode Screen 2

NOTE: When there is no Scan-to-Print license present, the FILE field will not be shown. Instead, it will be replaced by the phrase "NO SCAN-TO-NET LICENSE".

The FILE field has the following options to choose from:

LOCAL FILE - Creates a local file on the hard drive. DESTINATION 1 16 - Either an FTP or remote printer destination, configured via Web

Printer Management Tool "Configuration Scanner" page.

NOTE: At least one destination must be specified for a file. If you select NO FILE and disable the SCAN IMAGE TO PRINTER checkbox, then you will not be able to exit the screen until either the Scan-to-Print checkbox is selected, or a destination other than NO FILE is selected.

4. Press the Next key to highlight SCAN IMAGE TO PRINTER.

NOTE: When there is no Scan-to-Print license present, the SCAN IMAGE TO PRINTER selection field will not be shown. Instead, it will be replaced by the phrase "NO SCAN- TO-PRINT LICENSE".

5. Press the Enter key to enable SCAN IMAGE TO PRINTER. Press the Exit key to exit the menu. The processing time for Scan-to-Printer images will be longer, depending on the image size.

8 Special Feature Keys

90 Wide Format Copy System User Guide

This page has been intentionally left blank.

Wide Format Copy System User Guide 91

9 Scanning to the Network (SCAN mode)

Scanning to the Network (SCAN mode) The Wide Format Copy System has two scanning modes of operation: COPY mode and SCAN mode.

NOTE: Color Scan-to-Net is an available option for all XEROX Wide Format Copy Systems equipped with the Wide Format Scan System. The Color Scan-to-Net feature requires a separately purchased, Color Enablement feature key.

NOTE: The COPY mode will be disabled and the READY TO COPY screen will not be accessible when the SCAN OPTION (COLOR) is enabled and a color printer is connected to the Controller.

In COPY mode, documents are scanned and temporarily stored in memory or on the controller internal hard disk, and then sent to the local Printer as soon as the Printer is available. When the next job is scanned, the file from the previous job is automatically deleted from the hard disk, making room for new files. Operation of the system works as described in the previous sections.

In SCAN mode, the choices include:

Scan to Remote Destination: Scanned images can be transferred to up to 16 remote FTP or printer destinations. Before an image is scanned, the FTP Destination is selected on the Scan Systems Sample Mode screen. Scan to FTP images are not stored on the FreeFlow Accxes Controllers hard drive. Scan to remote printer images are stored on the FreeFlow Accxes Controllers hard drive. The FTP and Remote Printer features are located on the Sample Mode screen. See the Sample Key section of this guide for more information. The destination choices that show on the scan systems Sample Mode screen were defined on the Web Printer Management Tool page located at Configuration > Scanner.

NOTE: If the Image Overwrite feature is enabled, Scan to FTP is still available, but since the images are deleted from the hard drive, Scan to Remote Printer is disabled while the Image Overwrite feature is in effect.

If an internal error occurs while FTP transferring a scanned image to a remote file system, the scanned image will be deleted and the following error will be displayed. Setting up an FTP

9 Scanning to the Network (Scan Mode)

92 Wide Format Copy System User Guide

destination on the Web Printer Management Tool with an invalid user name and/or password, can also cause this error.

CONTROLLER FAULT

50000017: INTERNAL FAULT FTP TRANSFER FAILED SCANNED IMAGE DELETED

FTP Transfer Failed Screen

Scan-to-Net: The image file created by scanning is stored directly on the controller hard disk for later retrieval over a connected network by a remote system. The image is stored in Tagged Image File Format (TIFF) 6.0 using CCITT Group 4, CALS, Packbits, or PDF/A-1b. High- resolution JPG files and PDF/A-1b are also available with the Color Scan-to-Net option. Files stored in SCAN mode can be retrieved over the network. After the FreeFlow Accxes Client Tools program, which is running on a network-connected computer, retrieves the file, the image residing on the local hard disk is deleted automatically.

After a file has been on the local hard disk for longer than the time specified for the FILE DELETION Timer, the system automatically deletes the file. Refer to the Main Menu, CONFIGURATION menu, TIMERS section of this manual for information about setting the FILE DELETION timer.

Real-time PDF Scan-to-Net: Processing of the image for storage or transfer to a remote location is done at the same time the image is being scanned. This cannot be done when using the Color PDF Scan-to-Net feature.

Switching between COPY mode and SCAN mode NOTE: The COPY mode will be disabled and the READY TO COPY screen will not be

accessible when a color printer is connected to the Controller.

To switch between the COPY mode and the SCAN mode, perform the following steps:

1. Ensure that the READY TO COPY screen is displayed. If a menu is displayed, press the Menu key to return to the READY screen. If PLEASE ENTER ACCOUNT is displayed, enter a valid User ID code, and then enter a valid account number to obtain the READY screen.

2. Press the Mode key. The system switches to the SCAN mode and the screen now displays. Pressing the Mode key again returns the system to the COPY mode.

PLEASE ENTER DIRECTORY

Images

Please Enter Directory Screen

3. Enter a Directory name, up to 16 alphanumeric characters, to which you will scan the images. The name cannot begin with a period/decimal point.

9 Scanning to the Network (Scan Mode)

Wide Format Copy System User Guide 93

Understanding the READY TO SCAN screen Below is an example of the READY TO SCAN screen. Following the example are descriptions of the special information displayed on the screen.

READY TO SCAN INSERT DOCUMENT

400TIFF/CCITTG4 11 BIT

Ready to Scan Screen

TIFF/CCITTG4 1 BIT

This area indicates the selected file format. Refer to SCAN OPTIONS (LINE) or SCAN OPTIONS (PHOTO) or SCAN OPTIONS (COLOR) to set these options. The available options will differ depending upon your Scan Option selection.

This area shows the selected scanning resolution. Press the Previous or Next key to select a value of 100, 200, 300, 400, or interpolated 600 DPI (Dots Per Inch). A new value can be selected before each scan.

This icon shows how much Random Access Memory (RAM) is in use by the scanned file. As space is used, the dark area increases. After the scan is complete, the file is processed and then moved to the internal hard disk. The RAM space then becomes available again.

This icon shows how much hard disk space is in use by stored files. As space is used, the dark area increases. When files are moved off the disk over the network to remote devices, the space becomes available again. Files are also deleted when the age of the file exceeds the value set in the timer. Refer to Timers in the Main Menu section to set this value. The factory default is 24 hours.

Selections disabled in SCAN mode Certain selections available in COPY mode are not available in SCAN mode. The unavailable selections are:

Specifying the media Source and Type Since the output is now an electronic file, specifying the media is not applicable.

Specifying the output format The image file always has the format of the length of the document by the scan width. The scan width can be manually specified if the entire width of the document is not desired. Refer to Scan System Control in the Main Menu section to enable or disable manual specification of the scan width.

9 Scanning to the Network (Scan Mode)

94 Wide Format Copy System User Guide

Selection of Margins or Justification You can crop equal amounts from each side edge of the document by manually specifying a scan width that is narrower than the actual document. Refer to Scan System Control in the Main Menu section to enable or disable manual specification of the scan width.

Specification of Finishing Options Since there is no physical output, the finishing operations are not applicable.

Selection of Reduce/Enlarge - The electronic file is saved without alteration, so all scanned information is preserved.

Selection of Image Type. Only Line, Photo, Normal, and Color image types are valid for SCAN mode. Refer to the Image Quality, Scan Mode section in this manual for additional information

Background Suppression - This selection is automatically switched to OFF if a color printer is connected.

Operating in SCAN mode To scan documents for later retrieval over the network:

1. If job accounting is enabled, enter in your User ID and Account ID when prompted and press Enter. If job accounting is not enabled, you will not have to enter your IDs.

2. If you want to see a preview of the scanned images when they are retrieved from the Controller to your workstation, verify that the Scan Systems default PREVIEW box is checked when selecting the Original, Type. Use the Previous, Next, and Enter keys to enable PREVIEW. Use the Enter key to confirm your choice(s). For Normal and Line modes, you will be able to select single bit preview image scaling, and with Accxes 13.0, the system produces improved preview images for both Normal and Line modes.

3. With READY TO COPY is displayed on the Scan System Control Panel, press the Mode key to display READY TO SCAN.

4. Use the keypad on the Scan System Control Panel to enter in your 16 alphanumeric character Scan Directory name.

5. To view a sample of the file before it is scanned to a file, press the Sample key on the Control Panel. Use the Next or Previous key to highlight SCAN-TO-PRINTER and press the Enter key. Press the Exit key to return to the READY screen, and then press Start. A copy will be sent to the printer.

6. When the Scan System Control Panel displays READY TO SCAN, select your desired scanning resolution using the Next and Previous keys.

NOTE: When making a color scan, be sure to select Color with the arrow key under Image Quality on the Scan System Control Panel. The Normal and Photo lights will be on.

7. Select the Image Quality, Original, and Type by pressing the arrow button located under Type. When the Type (Normal, Line, Photo, or Color) is selected, the appropriate SCAN OPTION (NORMAL, LINE, PHOTO, or COLOR) is displayed. Use the Next, Previous, and Enter keys to navigate to and through the available options on the screen. Press the Enter key to confirm your choice(s). For additional information refer to the Image Quality, Scan Mode section of this manual.

8. Insert your original document face down and centered on the feed tray of the Scan System.

9 Scanning to the Network (Scan Mode)

Wide Format Copy System User Guide 95

9. Gently move your document forward until the Scan Systems feed rolls engage the documents leading edge.

10. If prompted to do so, enter the desired scanning width and press Enter. 11. As your document is automatically fed into the Scan System, the resulting image is

stored as a file in the Scan Directory on the system Controllers hard drive. The image can be retrieved at your workstation using the Document Retrieve Tool of the FreeFlow Accxes Client Tools.

NOTE: You may have to press the Start button if the configuration (for Auto Scan) has been changed from the factory default.

Clearing the scanned images The C/CA key enables you to remove scanned images from the Wide Format Copy System hard disk.

To clear scanned images:

1. Press the C/CA key. The CLEAR SCANNED IMAGE screen is displayed.

CLEAR SCANNED IMAGE

DO NOT CLEAR IMAGE

Clear Scanned Image Screen

2. Press the Previous or Next key to highlight the desired selection.

3. Press the Enter key to select the highlighted selection. The choices are:

DO NOT CLEAR IMAGE The image is not deleted.

CLEAR LAST IMAGE - The last image scanned by the currently active account is deleted. Press the C/CA key again, followed by the Enter key, to delete the next-to- last scanned image. This process can be repeated until all desired images are removed from the hard disk. It may take a few minutes longer to clear a scanned photo or an image with color.

NOTE: It is not possible to skip images. For example, it is not possible to leave the last image scanned, but delete the next-to-last image scanned. Photo and Color mode scans may take a few minutes to clear.

CLEAR ALL IMAGES All images stored under the currently active account are deleted.

If the scanned image is a multi page file, the choices are:

DO NOT CLEAR PAGE The page is not deleted.

CLEAR LAST PAGE - The last page scanned by the currently active account is deleted. Press the C/CA key again, followed by the Enter key, to delete the next-to- last scanned page. This process can be repeated until all desired pages are removed from the hard disk. It may take a few minutes longer to clear a scanned photo or an image with color.

9 Scanning to the Network (Scan Mode)

96 Wide Format Copy System User Guide

CLEAR ENTIRE MULTI-PAGE All pages stored under the currently active account are deleted.

Managing the File System The file system stores images in directories on the internal hard disk drive. The images are stored in the Directory specified by the user when entering the SCAN mode. The default directory is images. Managing the file system requires the System Administrator password.

The FILE SYSTEM option of the SYSTEM ADMINISTRATION menu enables the System Administrator to perform a number of file system management functions. They are:

Listing the number of images stored under each directory and the percentage of total hard disk space consumed by each account

Deleting all of the images scanned under any directory.

Deleting all of the images currently stored on the hard disk.

Refer to File System in the Main Menu section of this manual for complete information about the above functions.

Scanning Multiple Pages to Make a File To scan multiple tiffs and pdfs to make a file:

1. When the Scan System Control Panel displays READY TO SCAN, select your desired scanning resolution using the Next and Previous keys.

NOTE: When making a color scan, be sure to select Color with the arrow key under Image Quality on the Scan System Control Panel. The Normal and Photo lights will be on.

2. Select the Image Quality, Original, and Type by pressing the arrow button located under Type. When the Type (Normal, Line, Photo, or Color) is selected, the appropriate SCAN OPTION (NORMAL, LINE, PHOTO, or COLOR) is displayed. Use the Next, Previous, and Enter keys to navigate to and through the available options on the screen. Select the TIFF or PDF option. Press the Enter key to confirm your choice(s). For additional information refer to the Image Quality, Scan Mode section of this manual.

3. Select Sets Build. This opens the Multi-Page screen.

Building Multi-Page Screen

4. Insert your original document face down and centered on the feed tray of the Scan System.

5. Gently move your document forward until the Scan Systems feed rolls engage the documents leading edge.

6. If prompted to do so, enter the desired scanning width and press Enter.

9 Scanning to the Network (Scan Mode)

Wide Format Copy System User Guide 97

7. As your document is automatically fed into the Scan System, the resulting image is stored as a file in the Scan Directory on the system Controllers hard drive. The image can be retrieved at your workstation using the Document Retrieve Tool of the FreeFlow Accxes Client Tools.

8. Scan the documents. After you have scanned all of your pages, select Sets Build again.

All Pages Scanned Screen

9. Select Start.

9 Scanning to the Network (Scan Mode)

98 Wide Format Copy System User Guide

This page has been intentionally left blank.

Wide Format Copy System User Guide 99

10 Main Menu

Main Menu The Main Menu provides options for configuring the system, obtaining system information, performing system administration functions, and running system diagnostics.

When you access the Main Menu, a menu containing the following sub-menus is displayed:

CONFIGURATION - Enables you to configure the settings for a variety of system options. These include localization, the Scan System Control Panel, copy options, scan options for Normal, Line and Photo modes (and Color, if enabled), timers, the power saver timeout, and Scan System control for Copy and Scan modes.

SYSTEM INFORMATION - Enables you to obtain information about the system components, display the Scan System fault list, print configuration pages, and view user account information.

SYSTEM ADMINISTRATION - Enables the system administrator to perform job accounting, file system management, security, and change password functions. Access to this menu requires an administrators password.

DIAGNOSTICS - Enables the Customer Service Engineer and/or the operator to run a number of system diagnostic routines.

To access the Main Menu:

1. Press the Menu key.

READY TO COPY INSERT DOCUMENT

1

EnterNext ExitPrevious ModeMenu

100.0% AUTO

Ready to Copy Screen

The MAIN MENU screen is displayed. The black arrows indicate that the menu list contains more items than are visible. The selected option is highlighted.

10 Main Menu

100 Wide Format Copy System User Guide

MAIN MENU CONFIGURATION SYSTEM INFORMATION SYSTEM ADMINISTRATION

Main Menu Screen

2. Press the Previous or Next key to scroll through the list options.

3. When the desired option is highlighted, press the Enter key to select the option.

Configuration Menu The CONFIGURATION option of the Main Menu provides a sub-menu of the following choices:

LOCALIZATION - Sets the display language and units of measurements.

CONTROL PANEL - Controls whether the beeper is used for the key click and invalid entry beeps. Also allows selection of the font display style and the default operating mode.

COPY OPTIONS - Sets the choices for standard media series, custom media formats, custom reduction/enlargement values, and imaging parameters.

IMAGE ENHANCEMENTS - Enhances the appearance of a color scanned images in particular color halftones, Scanning speed BEST IQ and FASTEST, and Dynamic Background Removal. The FASTEST selections require the Turbo III.

TIMERS - Sets the values for the Feature, Printer Interrupt, and File Deletion timers.

POWER SAVER - Sets the number of hours of inactivity after which the system goes into Power Saver mode.

SCANNER CONTROL - Sets the choices for the operation of the Scan System for both copying and scan-to-file. Auto Scan, Document Return, and Mode (Manual Width, Auto Width).

To access the CONFIGURATION menu:

1. Press the Menu key. The MAIN MENU screen is displayed.

2. Press the Enter key to select CONFIGURATION. The CONFIGURATION menu screen is displayed. The black arrows indicate the menu contains more options than are visible. The selected option is highlighted.

CONFIGURATION LOCALIZATION CONTROL PANEL COPY OPTIONS

Configuration Screen

3. Press the Previous or Next key to scroll through the list of options.

4. When the desired option is highlighted, press the Enter key to select the options. The menu or screen for the selected option is displayed.

10 Main Menu

Wide Format Copy System User Guide 101

Localization The LOCALIZATION option of the CONFIGURATION menu sets the language in which messages are displayed. It also controls whether measurements are displayed in English or metric units.

To set the display language or display units:

1. Press the Menu key. The MAIN MENU screen is displayed.

2. Press the Enter key to select CONFIGURATION. The CONFIGURATION menu screen is displayed.

3. Press the Enter key to select LOCALIZATION. The LOCALIZATION screen is displayed. Below is an example of the LOCALIZATION screen.

LOCALIZATION LANGUAGE: DISPLAY UNITS:

ENGLISH

Localization Screen

4. Press the Previous or Next key to highlight LANGUAGE or DISPLAY UNITS.

5. Press the Enter key to select the highlighted option.

6. Press the Previous or Next key to highlight the desired setting for the option.

The choices for LANGUAGE are ENGLISH, SPANISH, FRENCH, ITALIAN, GERMAN, RUSSIAN, or PORTUGUESE. ENGLISH is the default setting.

The choices for DISPLAY UNITS are INCHES or MM (MILLIMETERS). INCHES is the default setting.

7. Press the Enter key to select the highlighted setting.

8. Repeat steps 4 through 6 to change the remaining setting, if desired.

9. Press the Exit key to return to the CONFIGURATION menu screen.

Control Panel The CONTROL PANEL option of the CONFIGURATION menu controls whether the beeper is used for the key click and invalid entry beeps. It also allows selection of the font display style and the default mode of operation for the Wide Format Copy System.

To set the beeper, text style or default operating mode:

1. Press the Menu key. The MAIN MENU screen is displayed.

2. Press the Enter key to select CONFIGURATION. The CONFIGURATION menu screen is displayed.

3. Press the Next key to select CONTROL PANEL.

4. Press the Enter key to select CONTROL PANEL. The CONTROL PANEL screen is displayed. Below is an example of the CONTROL PANEL screen.

10 Main Menu

102 Wide Format Copy System User Guide

CONTROL PANEL BEEPER: TEXT:

DEFAULT MODE:

ENABLED NORMAL

COPY

Control Panel Screen 5. Press the Previous or Next key to highlight BEEPER, TEXT MODE or DEFAULT

MODE.

6. Press the Enter key to select the highlighted option.

7. Press the Previous or Next key to highlight the desired setting for the option.

The choices for BEEPER are ENABLED or DISABLED. ENABLED is the default setting. The Initialization Beep and the Fault Beep are not affected by this setting and cannot be turned off.

The choices for TEXT are NORMAL or BOLD. NORMAL is the default setting.

The choices for DEFAULT MODE are COPY or SCAN. COPY is the default setting.

NOTE: The DEFAULT MODE setting will not be displayed unless the Scan-to-Net feature is enabled. Press the Enter key to select the highlighted setting.

8. Repeat steps 5 through 8 if you wish to change another setting.

9. Press the Exit key to return to the CONFIGURATION menu screen.

Copy Options The COPY OPTIONS feature of the CONFIGURATION menu provides a sub-menu of the following choices:

MEDIA SERIES Sets the standard media sizes for preset output formats. Table 5 shows the standard media series and the sizes associated with them.

CUSTOM MEDIA FORMATS Sets the custom media sizes for preset output formats.

CUSTOM R/E PRESETS Sets the reduction/enlargement ratios

IMAGING Sets the imaging options.

To access the COPY OPTIONS menu:

1. Press the Menu key. The MAIN MENU screen is displayed.

2. Press the Enter key to select CONFIGURATION. The CONFIGURATION menu screen is displayed.

10 Main Menu

Wide Format Copy System User Guide 103

3. Press the Next key until COPY OPTIONS is displayed. The COPY OPTIONS menu screen is displayed. The black arrows indicate that the menu contains more options than are visible. The selected option is highlighted.

COPY OPTIONS MEDIA SERIES CUSTOM MEDIA FORMATS CUSTOM R/E PRESETS

Copy Options Screen

4. Press the Previous or Next key to scroll through the list of options.

5. Press the Enter key to select the highlighted option. The screen for the selected option is displayed.

Table 2. Media Series Options

Choose Series

To Display Sizes

Dimensions (width x length)

ANSI A 8.5 x 11 inches (215.9 x 279.4 mm)

B 11 x 17 inches (279.4 x 431.8 mm)

C 17 x 22 inches (431.8 x 558.8 mm)

D 22 x 34 inches (558.8 x 863.6 mm)

E 34 x 44 inches (836.6 x 1117.6 mm)

ARCH A 9 x 12 inches (228.6 x 304.8 mm)

B 12 x 18 inches (304.8 x 457.2 mm)

C 18 x 24 inches (457.2 x 609.6 mm)

D 24 x 36 inches (609.6 x 914.4 mm)

E 36 x 48 inches (914.4 x 1219.2 mm)

30 30 x 42 Inches (76.2 x 106.7 mm)

ISO A A4 210 x 297 mm

A3 297 x 420 mm

A2 420 x 594 mm

A1 594 x 841 mm

A0 841 x 1189 mm

ISO B B4 250 x 353 mm

B3 353 x 500 mm

B2 500 x 707 mm

B1 707 x 1000 mm

10 Main Menu

104 Wide Format Copy System User Guide

JIS B B4 257 x 364 mm

B3 364 x 515 mm

B2 515 x 728 mm

B1 728 x 1030 mm

Media Series The MEDIA SERIES option controls which standard media series are displayed when Preset is selected from the Output Format portion of the Scan System Control Panel.

You can select one or more media series to be displayed. Refer to Table 5 for a listing of the sizes associated with each media series.

To enable/disable a media series:

1. Press the Menu key. The MAIN MENU screen is displayed.

2. Press the Enter key to select CONFIGURATION. The CONFIGURATION menu screen is displayed.

3. Press the Next key until COPY OPTIONS is highlighted.

4. Press the Enter key to select COPY OPTIONS. The COPY OPTIONS menu screen is displayed.

5. Press the Enter key to select MEDIA SERIES. The MEDIA SERIES screen is displayed. Below is an example of the MEDIA SERIES screen.

MEDIA SERIES ANSI ISO A ARCH ISO B

JIS B

Media Series Screen

6. Press the Previous or Next key to highlight a media series.

7. Press the Enter key to ENABLE or DISABLE the highlighted media series. A checkmark appears in the box to the left of the series when the series is enabled.

The factory default setting is ENABLED for the ANSI media series and DISABLED for all others.

8. Repeat steps 6 and 7 for each media series you wish to enable or disable.

9. Press the Exit key to return to the COPY OPTIONS menu screen.

10 Main Menu

Wide Format Copy System User Guide 105

Custom Media Formats The CUSTOM MEDIA FORMATS option controls which custom media formats are displayed when Preset is selected from the Output Format portion of the Scan System Control Panel. You can specify up to six custom media formats. To use the SCANNER CONTROL, MODE: PRODUCTIVITY: CUSTOM mode, the custom sizes must be entered in the CUSTOM MEDIA FORMATS.

To specify a custom media format:

1. Press the Menu key. The MAIN MENU screen is displayed.

2. Press the Enter key to select CONFIGURATION. The CONFIGURATION menu screen is displayed.

3. Press the Next key until COPY OPTIONS is highlighted.

4. Press the Enter key to select COPY OPTIONS. The COPY OPTIONS menu screen is displayed.

5. Press the Next key to highlight CUSTOM MEDIA FORMATS.

6. Press the Enter key to select CUSTOM MEDIA FORMATS. The CUSTOM MEDIA FORMATS screen is displayed.

The first "0.0" in each "0.0 x 0.0" format represents the width. The second "0.0" represents the length.

NOTE: The formats are expressed in the units of measurement selected for the machine. Refer to "Localization" in the "Main Menu" section for further information.

Below is an example of the MEDIA SERIES screen. In the example, the display units have been set to inches.

CUSTOM MEDIA FORMATS (IN) 0.0 X 0.0 0.0.X 0.0

0.0 X 0.0 0.0.X 0.0

0.0 X 0.0 0.0.X 0.0

Custom Media Formats Screen

7. Press the Previous or Next key to highlight the desired field.

8. Use the numeric keypad to enter the value for the highlighted field.

9. Widths in excess of 36 inches (914 mm) or less than 11 inches (297 mm) are not valid.

10. Press the Enter key to confirm the value.

11. Repeat steps 7 through 9 until all desired formats are defined.

NOTE: Any custom formats that are not defined are automatically set to zero and are not displayed elsewhere.

12. Press the Exit key to return to the COPY OPTIONS menu screen.

10 Main Menu

106 Wide Format Copy System User Guide

Custom R/E Presets The CUSTOM R/E PRESETS option controls which reduction/enlargement ratios are displayed when Preset is selected from the Reduction/Enlargement portion of the Scan System Control Panel. You can specify up to six reduction/enlargement presets.

To specify a reduction/enlargement preset:

1. Press the Menu key. The MAIN MENU screen is displayed.

2. Press the Enter key to select CONFIGURATION. The CONFIGURATION menu screen is displayed.

3. Press the Next key until COPY OPTIONS is highlighted.

4. Press the Enter key to select COPY OPTIONS. The COPY OPTIONS menu screen is displayed.

5. Press the Next key until CUSTOM R/E PRESETS is highlighted.

6. Press the Enter key to select CUSTOM R/E PRESETS. The CUSTOM R/E PRESETS screen is displayed. Below is an example of the CUSTOM R/E PRESETS screen.

CUSTOM R/E PRESETS 100.0% 100.0% 100.0% 100.0% 100.0% 100.0%

Custom R/E Presets Screen

7. Press the Previous or Next key to highlight the value that you wish to change.

8. Use the numeric keypad to enter the desired value. The valid value range is from 25% to 400%.

NOTE: Duplicate values are not displayed in the Preset Reduction/Enlargement list. You can remove a preset value from the list by setting the value to 100.0%.

9. Press the Enter key to confirm the value.

10. Repeat steps 7 through 9 for each value you wish to change.

11. Press the Exit key to return to the COPY OPTIONS menu screen.

Imaging The IMAGING option allows you to perform the following functions:

AUTO ROTATE - Enable or disable automatic image rotation. If AUTO ROTATE is enabled, the scanned image will be electronically rotated 90 degrees only to match one of the page dimensions, prevent clipping on the selected roll, or to correct the orientation for use with the folder.

REDUCTION LINE PRESERVATION - Use this feature to enable/disable line preservation when reducing normal and line-mode documents.

MAXIMUM COPY LENGTH To see what your Scan Systems maximum copy length is, select the Menu key > Configuration > Copy Options > Imaging >

10 Main Menu

Wide Format Copy System User Guide 107

Maximum Copy Length. The default is 100 feet. For the 6030/6050/6050A, the scanned copy would get cut off at 3 meters.

WARNING: Copy documents that are larger than the printers maximum capability will not print correctly, or may not print at all.

To enable/disable the imaging options:

1. Press the Menu key. The MAIN MENU screen is displayed.

2. Press the Enter key to select CONFIGURATION. The CONFIGURATION menu screen is displayed.

3. Press the Next key until COPY OPTIONS is highlighted.

4. Press the Enter key to select COPY OPTIONS. The COPY OPTIONS menu screen is displayed.

5. Press the Next key until IMAGING is highlighted.

6. Press the Enter key to select IMAGING. The IMAGING screen is displayed. Below is an example of the IMAGING screen.

IMAGE ENHANCEMENT

COLOR IQ: SRGB

IMAGING

AUTO-ROTATE

MAXIMUM COPY LENGTH: 1200.0 IN

REDUCTION LINE PRESERVATION

Imaging Screen

7. Press the Previous or Next key to highlight the desired option.

8. Press the Enter key to enable or disable the highlighted option. A checkmark appears in the box to the left of the option when the option is enabled.

The factory default setting is disabled for AUTO-ROTATE.

9. Repeat steps 7 and 8 to enable or disable REDUCTION LINE PRESERVATION, if desired.

10. Press the Exit key to return to the COPY OPTIONS menu screen.

Image Enhancements The IMAGE ENHANCEMENT feature settings are used to enhance the appearance of color scanned images, particularly halftone color originals (for example, maps).

This feature will greatly enhance the printing of a color sample using the Color Scan-to-Print feature key.

To enable the IMAGE ENHANCEMENT features, perform the following:

1. Select the Menu key.

2. Press the Enter key to select CONFIGURATION. The CONFIGURATION menu screen is displayed.

3. Press the Next key until IMAGE ENHANCEMENT is highlighted.

4. Press the Enter key to select IMAGE ENHANCEMENT. The IMAGE ENHANCEMENT menu screen is displayed.

5. Press the Next key to highlight COLOR IQ.

10 Main Menu

108 Wide Format Copy System User Guide

6. Press the Enter key to select COLOR IQ. The COLOR IQ screen is displayed.

IMAGE ENHANCEMENT

COLOR IQ: SRGB COLORIQ:

DYNAMIC BACKGROUND REMOVAL

SRGB

NORMAL MODE: BEST IQ

Image Enhancement Screen 7. Press the Next key to select the enhancement option you want:

NONE: scanned color has no color correction applied.

SRGB: scanned colors will be converted to the SRGB (Standard Red Green Blue) color space

ADAPTIVE CONTRAST: scanned colors are first converted to the SRGB color space, and then enhanced using an adaptive contrast algorithm. The adjustment changes the images white point, black point,

NOTE: Further color halftone image enhancement can be achieved when printing by enabling the Error Diffusion Raster Halftone Method in the controller Web Printer Management Tool. The setting is found on the Processing Defaults page. Select Error Diffusion from the Raster Halftone Method pull-down menu.

8. Press the Enter key to select the enhancement setting.

9. Press the Next key to select NORMAL MODE then press the Enter key to select Normal Mode.

10. Press Previous or Next to scroll through the settings BEST IQ and FASTEST, then press the Enter key to select the setting. BEST IQ is the default.

11. Press the Next key to select DYNAMIC BACKGROUND SUPPRESSION. Then press the Enter key to enable/disable DYNAMIC BACKGRO UND REMOVAL. Disabling the DYNAMIC BACKGROUND REMOVAL enables the STATIC BACKGROUND REMOVAL. DYNAMIC BACKGROUND REMOVAL is the default and should be used for most document types.

12. Press the Enter key to confirm the selection.

13. Press the Exit key to return to the CONFIGURATION menu.

Timers The TIMERS option of the CONFIGURATION menu allows you to set the values for the time-out functions. Pressing any key or scanning a document resets the timers.

The timers are as follows:

FEATURE Controls how long the current feature parameters remain in effect after the last key press, scan completion, or insertion of a document into the Scan System. The FEATURE timer can be set between 0 and 99 minutes. The factory default is 5 minutes. A value of 0 means that the feature will never time out.

NOTE: To prevent images from being lost, feature time-outs will not occur during the sets build process.

10 Main Menu

Wide Format Copy System User Guide 109

PRINTER INTERRUPT - Controls how long the Printer remains in the interrupted state with no interruption at the Scan System Control Panel. This timer pertains to print jobs that have been interrupted to allow a copy job to process. The allowed range is 1 to 99 minutes. The factory default is 1 minute.

FILE DELETION - Specifies the maximum amount of time a scanned image file remains on the file system before being deleted. This timer pertains only to files scanned when the Wide Format Copy System is in the READY TO SCAN mode. This timer can be set between 1 and 24 hours in increments of 1 hour. When a file is scanned in, it is given a time stamp. When the age of the file on the hard disk exceeds the value of the FILE DELETION timer, the file is automatically deleted to allow space for new files. The default value is 24 hours. After the files have been deleted, the directory will also be deleted if no other files are scanned to it.

To adjust a timer:

1. Press the Menu key. The MAIN MENU screen is displayed.

2. Press the Enter key to select CONFIGURATION. The CONFIGURATION menu screen is displayed.

3. Press the Next key until TIMERS is highlighted.

4. Press the Enter key to select TIMERS. The TIMERS screen is displayed.

TIMERS FEATURE (0 99) MIN 5

PRINTER INTERRUPT (1 99 MIN): 1

FILE DELETION (1-24 HR): 24

Timers Screen

5. Press the Previous or Next key to highlight the desired timer.

6. Press the Enter key to select the highlighted timer.

7. Use the numeric keypad to enter the timer value.

8. Press the Enter key to confirm the value.

9. Repeat steps 5 through 8 if you want to set the value for additional timers.

10. Press the Exit key to return to the CONFIGURATION menu screen.

Power Saver The POWER SAVER option of the CONFIGURATION menu allows you to set the number of hours of inactivity after which the system goes into Power Saver mode.

To adjust the power saver:

1. Press the Menu key. The MAIN MENU screen is displayed.

2. Press the Enter key to select CONFIGURATION. The CONFIGURATION menu screen is displayed.

3. Press the Next key until POWER SAVER is highlighted.

4. Press the Enter key to select POWER SAVER. The POWER SAVER screen is displayed.

10 Main Menu

110 Wide Format Copy System User Guide

POWER SAVER POWER SAVER DELAY (0 4 HR): 3

Power Saver Screen

5. Use the numeric keypad to enter the power saver value. The valid value range is 0 to 4 hours. The factory default is 3 hours.

6. Press the Enter key to confirm the value.

7. Press the Exit key to return to the CONFIGURATION menu screen.

Scanner Control The SCANNER CONTROL option of the CONFIGURATION menu allows you to set the options for how the Scan System starts and finishes a scan. It contains the following features:

AUTOSCAN - Tells the Scan System either to start the scan automatically when the document is inserted (ENABLED), or to wait until the Start key is pressed (DISABLED). ENABLED is the factory default setting.

DOCUMENT RETURN - Tells the Scan System, after the scan, either to return the document to the front of the Scan System (FRONT), or to drop the document from the rear of the Scan System into the catch tray (REAR). REAR is the factory default setting.

NOTE: Refer to Controlling the Scan for additional information.

MODE: (PRODUCTIVITY is the default.)

MANUAL WIDTH - The user must enter the document width and very carefully center the document. In this mode the document will be prescanned.

AUTOWIDTH - Enables the automatic detection of the width of the document. In this mode the document will be prescanned.

AUTOWIDTH/AUTOCENTER - Enables the automatic centering of the image and automatic width detection. This selection is the default. In this mode the document will be prescanned.

PRODUCTIVITY - This feature does not use AUTOCENTER, requiring the operator to manually align the document within the media guidelines on the Feed-in Tray. The width sensors eliminate the need for a prescan, thereby increasing the overall throughput of the system resulting in higher productivity. When this feature is used, the operator must select the media series, ANSI, ARCH, ISO A, ISO B JIS B and CUSTOM etc. since the number of sensors provided cannot monitor every media type. To use the MODE: PRODUCTIVITY: CUSTOM the custom sizes must be entered in the CUSTOM MEDIA FORMATS (Select the Menu key > CONFIGURATION>COPY OPTIONS).

To set the Scanner Control features:

1. Press the Menu key. The MAIN MENU screen is displayed.

2. Press the Enter key to select CONFIGURATION. The CONFIGURATION menu screen is displayed.

10 Main Menu

Wide Format Copy System User Guide 111

3. Press the Next key until SCANNER CONTROL is highlighted.

4. Press the Enter key to select SCANNER CONTROL. The SCANNER CONTROL screen is displayed.

SCANNER CONTROL

DOCUMENT RETURN: AUTOSCAN

MODE:

FRONT

AUTOWIDTH/AUTOCENTER

ScannerControl Screen

5. Press the Previous or Next key to select the desired feature.

6. Press the Enter key to confirm the choice.

7. Press the Previous or Next key to select the desired setting.

For AUTOSCAN, you can enable or disable the feature. A checkmark in the box to the left of the feature indicates that the feature is enabled. Enabled is the factory default setting for these features.

For DOCUMENT RETURN, the selections are FRONT and REAR. FRONT is the factory default setting.

For MODE: use the Previous or Next keys to select the desired option then press the Enter key to confirm the choice. The options are MANUAL, AUTOWIDTH, AUTOWIDTH/AUTOCENTER, or PRODUCTIVITY. If PRODUCTIVITY is selected, then use the Previous or Next key to select the ANSI, ARCH, ISO A, ISO B, JISB, or CUSTOM setting.

Use the CUSTOM setting when documents of mixed series will be scanned in the same job. The CUSTOM selection uses the custom sizes that are entered in the CUSTOM MEDIA SIZES (Menu key > CONFIGURATION>COPY OPTIONS).

CUSTOM MEDIA FORMATS (IN) 0.0 X 0.0 0.0.X 0.0

0.0 X 0.0 0.0.X 0.0

0.0 X 0.0 0.0.X 0.0

Custom Media Formats Screen

8. Press the Exit key to return to the CONFIGURATION menu screen.

10 Main Menu

112 Wide Format Copy System User Guide

System Information Menu The SYSTEM INFORMATION option of the MAIN MENU contains the following menu choices:

SYSTEM DESCRIPTION - Provides information about each component connected to the Wide Format Copy System.

RECENT FAULT LIST - Displays the most recent faults related to the Scan System.

CONFIGURATION PRINTS - Prints Copier and Printer configuration pages.

To access the SYSTEM INFORMATION menu:

1. Press the Menu key. The MAIN MENU screen is displayed.

2. Press the Next key to highlight SYSTEM INFORMATION.

3. Press the Enter key to select SYSTEM INFORMATION. The SYSTEM INFORMATION menu screen is displayed. The black arrows indicate that the menu contains more options than are visible. The selected option is highlighted.

SYSTEM INFORMATION SYSTEM DESCRIPTION RECENT FAULT LIST CONFIGURATION PRINTS

System Information Screen

4. Press the Previous or Next key to scroll through the list of options.

5. When the desired option is highlighted, press the Enter key to select the option. The menu or screen for the selected option is displayed.

System Description The SYSTEM DESCRIPTION option of the SYSTEM INFORMATION menu provides information on the model identity and firmware version for each component connected to the Wide Format Copy System.

To display component information:

1. Press the Menu key. The MAIN MENU screen is displayed.

2. Press the Next key to highlight the SYSTEM INFORMATION option.

3. Press the Enter key to select SYSTEM INFORMATION. The SYSTEM INFORMATION menu screen is displayed.

4. Press the Enter key to select SYSTEM DESCRIPTION. The SYSTEM DESCRIPTION screen is displayed.

SYSTEM DESCRIPTION SCANNER

CONTROLLER CONTROL PANEL

System Description Screen

10 Main Menu

Wide Format Copy System User Guide 113

5. Press the Previous or Next key to highlight the component about which you want to view information.

6. Press the Enter key to select the highlighted component. The screen for the selected component is displayed. Following are examples of the screens for each of the components.

SCANNER

MODEL: XEROX WIDE FORMAT SCAN SYSTEM

FIRMWARE: 3.2.8

Scanner Screen

CONTROLLER MODEL: 4

FIRMWARE: 10.0

RAM: 512MB

Controller Screen

NOTE: The CONTROLLER screen also provides the amount of Random Access Memory (RAM).

CONTROL PANEL MODEL: 1 FIRMWARE: 1.1.0

Control Panel Screen

PRINTER

MODEL: XEROX XXXX WIDE FORMAT

FIRMWARE: XXX

Printer Screen

NOTE: The XXXX represents the Printer name.

10 Main Menu

114 Wide Format Copy System User Guide

FINISHER

MODEL:

NONE

Finisher Screen

NOTE: This screen identifies the Finisher, if any. If there is no finisher, the MODEL is displayed as NONE. If a Folder is connected, the FINISHER screen displays the configuration of the connected Folder.

7. Press the Exit key to return to the SYSTEM DESCRIPTION screen.

Recent Fault List The RECENT FAULT LIST option of the SYSTEM INFORMATION menu displays the most recent faults related to the Scan System. Fault messages are stored in the Controller. Each fault message contains a fault code and a digital time stamp. When you call for service, the service center may ask you for this information.

To display the recent fault list:

1. Press the Menu key. The MAIN MENU screen is displayed.

2. Press the Next key to highlight SYSTEM INFORMATION.

3. Press the Enter key to select SYSTEM INFORMATION. The SYSTEM INFORMATION menu screen is displayed.

4. Press the Next key to highlight RECENT FAULT LIST. Press the Enter key to select RECENT FAULT LIST. The RECENT FAULT LIST screen is displayed. Below is an example of the RECENT FAULT LIST screen. The first column is the time given in seconds since January 1, 1970. That's what is used to determine the actual system date and time.

5. Go to the Problem Solving section of this document to look up the second columns fault code.

RECENT FAULT LIST 37449914 50000008 37449868 50000008

Recent Fault List Screen

6. Press the Previous or Next key to scroll through the list.

7. Press the Exit key to return to the SYSTEM INFORMATION menu screen.

10 Main Menu

Wide Format Copy System User Guide 115

Configuration Prints The CONFIGURATION PRINTS option of the SYSTEM INFORMATION menu allows you to print one of the following selections:

Copier Configuration

Printer Configuration

Printer Settings

All of the above.

To print a configuration print:

1. Press the Menu key. The MAIN MENU screen is displayed.

2. Press the Next key to highlight SYSTEM INFORMATION.

3. Press the Enter key to select SYSTEM INFORMATION. The SYSTEM INFORMATION menu screen is displayed.

4. Press the Previous or Next key until CONFIGURATION PRINTS is highlighted.

5. Press the Enter key to select CONFIGURATION PRINTS. The CONFIGURATION PRINTS screen is displayed.

CONFIGURATION COPIER CONFIGURATION PRINTER CONFIGURATION PRINTER SETTINGS ALL CONFIGURATION PRINTS

Configuration Screen

6. Press the Previous or Next key to highlight the configuration page you want to print.

7. Press the Enter key to select the highlighted configuration. The screen for the selected configuration is displayed. The default response is YES.

Below is an illustration of the COPIER CONFIGURATION screen.

COPIER CONFIGURATION

QUEUE TO PRINTER: YES

Copier Configuration Screen

8. Press the Enter key to confirm the response. A status message is displayed indicating that the configuration has been queued to the Printer.

10 Main Menu

116 Wide Format Copy System User Guide

Below are illustrations of the other CONFIGURATION PRINT screens with the status message.

PRINTER CONFIGURATION

QUEUE TO PRINTER: YES

Printer Configuration Screen

PRINTER SETTINGS

QUEUE TO PRINTER: YES

Printer Settings Screen

ALL CONFIGURATION PRINTS

QUEUE TO PRINTER: YES

All Configuration Prints Screen

9. Press the Exit key to return to the CONFIGURATION PRINTS screen.

10 Main Menu

Wide Format Copy System User Guide 117

System Administration Menu The SYSTEM ADMINISTRATION option of the MAIN MENU is reserved for the system administrator. It can be accessed only after entering the system administration password.

When this option is selected, the system administrator is immediately prompted for a password. See "Entering the system administration password" in this section for complete information about the password entry.

Once the system administration password has been entered correctly, the SYSTEM ADMINISTRATION menu screen is displayed. It contains the following options:

JOB ACCOUNTING MODE - Allows the system administrator to enable the Job Accounting Mode. The options are DISABLED, ENABLED, and OPTIONAL. The default is DISABLED.

FILE SYSTEM - Allows the system administrator to view and delete account information.

CHANGE PASSWORD - Allows the system administrator to change the system administration password.

SECURITY SETTINGS - Allows the system administrator to set the image recall feature. The immediate overwriting of data to DOD specification is such that the system, at any point in its operation, can be considered secure and all data will be removed no matter what operation the customer is performing.

Entering the System Administration Password Access to the SYSTEM ADMINISTRATION menu requires the entry of the system administration password.

To enter the system administration password:

1. Press the Menu key. The MAIN MENU screen is displayed.

2. Press the Previous or Next key until SYSTEM ADMINISTRATION is highlighted.

3. Press the Enter key to select SYSTEM ADMINISTRATION. The SYSTEM ADMINISTRATION password screen is displayed.

SYSTEM ADMINISTRATION ENTER PASSWORD:

System Administration Screen

4. Use the numeric keypad to enter the password. The password will display as asterisks.

5. Press the Enter key to confirm the password entry. The SYSTEM ADMINISTRATION menu screen is displayed. The black arrows indicate that the menu contains more options than are visible. The selected option is highlighted.

10 Main Menu

118 Wide Format Copy System User Guide

SYSTEM JOB ACCOUNTING MODE FILE SYSTEM CHANGE PASSWORD

SECURITY SETTINGS

System Screen

NOTE: If an incorrect password is entered, an error message will be displayed as shown below. Enter the password again.

SYSTEM ADMINISTRATION PASSWORD: *****

INVALID PASSWORD, RE-ENTER

System Administration Screen

6. Press the Previous or Next key to scroll through the list of system administration options.

7. Press the Enter key to select the desired option.

Job accounting The JOB ACCOUNTING option of the System Administration menu allows the system administrator with access to enable Job Accounting. The options are DISABLED, ENABLED, and OPTIONAL. The default is DISABLED.

File System The FILE SYSTEM option of the SYSTEM ADMINISTRATION menu provides a sub-menu of the following menu choices:

LIST BY DIRECTORY- Allows the system administrator to list the number of images stored under each directory and the percentage of total hard disk space consumed by the directory.

DELETE IMAGES - Allows the system administrator to delete all of the images scanned for a particular directory.

DELETE ALL IMAGES - Allows the system administrator to delete all of the images currently stored on the hard disk.

To access the FILE SYSTEM menu:

1. Access the SYSTEM ADMINISTRATION menu. See Entering the system administration password in this section.

2. Press the Next key to highlight FILE SYSTEM.

3. Press the Enter key to select FILE SYSTEM. The FILE SYSTEM menu screen is displayed.

10 Main Menu

Wide Format Copy System User Guide 119

FILE SYSTEM LIST BY DIRECTORY DELETE IMAGES DELETE ALL IMAGES

File System Screen

4. Press the Previous or Next key to highlight the desired option.

5. Press the Enter key to select the highlighted option.

Listing Stored Image Information by Directory The LIST BY DIRECTORY option allows the system administrator to display a list of the number of images stored under each directory and the percentage of total hard disk space consumed by each account.

To list scanned image information by account:

1. Access the SYSTEM ADMINISTRATION menu. See "Entering the system administration password" in this section.

2. Press the Next key to highlight FILE SYSTEM.

3. Press the Enter key to select FILE SYSTEM. The FILE SYSTEM menu screen is displayed.

4. Press the Enter key to select LIST BY DIRECTORY. The LIST BY DIRECTORY screen is displayed. The following illustration is a DIRECTORY example of the LIST BY screen.

NOTE: Directories that do not contain files will not be displayed. Directories not containing files are deleted.

LIST BY DIRECTORY DIRECTORY COUNT SIZE (%)

images 2* <1

images 35 2

List by Directory Screen

For each directory, the account name (DIRECTORY), the number of images stored under the directory (COUNT), and the percentage of total disk space consumed by the account (SIZE (%)) are shown. The length of the directory name may cause the information associated with the directory to wrap to the next line. Also, if the directory name exceeds the character limit of the first line, the name will be truncated at the width of the screen.

Use the Previous or Next key to scroll through the list.

An asterisk in the COUNT field indicates that some images in memory have not yet been processed. A <1 in the SIZE field indicates the account uses less than 1% of the total disk space on the file system.

5. Press the Exit key to return to the FILE SYSTEM menu screen.

10 Main Menu

120 Wide Format Copy System User Guide

The DELETE IMAGE option allows the system administrator to delete all the images stored for a particular account.

To delete stored images by account:

Deleting Stored Images by Directory 1. Access the SYSTEM ADMINISTRATION menu. See Entering the system

administration password in this section.

2. Press the Next key to highlight FILE SYSTEM.

3. Press the Enter key to select FILE SYSTEM. The FILE SYSTEM menu screen is displayed.

4. Press the Next key to highlight DELETE IMAGES.

5. Press the Enter key to select DELETE IMAGES. The DELETE IMAGES screen is displayed.

DELETE IMAGES DIRECTORY:

Images

Delete Images Screen

6. Use the numeric keypad to enter the name of the directory from which you would like delete the stored images.

7. Press the Enter key to confirm the account number. A delete confirmation screen is displayed. The default response is NO.

The following illustration is an example of the DELETE IMAGES screen.

DELETE IMAGES DIRECTORY:

Images

ARE YOU SURE ? NO

Delete Images- Are You Sure Screen 8. Press the Previous or Next key to change the response to YES.

9. Press the Enter key to confirm the deletion. While the deletion is in process, a DELETING. . . message is displayed. When the deletion is complete, the status changes to IMAGES DELETED. Below is an example of the deletion screen.

10 Main Menu

Wide Format Copy System User Guide 121

DELETE IMAGES DIRECTORY:

IMAGES DELETED Images

Delete Images Images Deleted Screen

10. Press the Exit key to return to the FILE SYSTEM menu screen.

The DELETE ALL IMAGES option allows the system administrator to delete all the images stored on the file system.

Deleting All Stored Images To delete all stored images:

1. Access the SYSTEM ADMINISTRATION menu. See "Entering the system administration password" in this section.

2. Press the Next key to highlight FILE SYSTEM.

3. Press the Enter key to select FILE SYSTEM. The FILE SYSTEM menu screen is displayed.

4. Press the Next key until DELETE ALL IMAGES is highlighted.

5. Press the Enter key to select DELETE ALL IMAGES. The DELETE ALL IMAGES screen is displayed. The default response is NO.

DELETE ALL IMAGES ARE YOU SURE?: NO

Delete All Images Screen

6. Press the Previous or Next key to change the response to YES.

7. Press the Enter key to confirm the deletion. While the deletion is in process, a "DELETING. . ." message is displayed. When the deletion is complete, the status changes to IMAGES DELETED.

DELETE IMAGES ARE YOU SURE?: YES

IMAGES DELETED

Delete Images Are You Sure Screen

10 Main Menu

122 Wide Format Copy System User Guide

8. Press the Exit key to return to the FILE SYSTEM menu screen.

Change Password The CHANGE PASSWORD option of the SYSTEM ADMINISTRATION menu allows the system administrator to change the system administration password.

The default system administration password on all newly delivered machines is 0 (zero). The system administrator is required to change the password after the initial log in. Immediately following the log in, the CHANGE PASSWORD screen is displayed. The password must be changed at that time.

If the existing password has been lost, call for service. The customer service engineer will reset the password to the default value of 0. The system administrator should then change the password to a different value.

NOTE: Changing the system administrator password on the Scan System Control Panel also changes the system administrator password for the Printer. These two passwords always have the same value.

To change the system administration password:

1. Select the Menu key.

2. Access the SYSTEM ADMINISTRATION menu. See "Entering the system administration password" in this section.

3. Press the Next key until CHANGE PASSWORD is highlighted.

4. Press the Enter key to select CHANGE PASSWORD. The CHANGE PASSWORD screen is displayed.

CHANGE PASSWORD ENTER OLD PASSWORD:

Change Password Screen

5. Use the numeric keypad to enter the old password.

6. Press the Enter key to confirm the old password. The CHANGE PASSWORD screen will instruct you to enter the new password.

CHANGE PASSWORD ENTER NEW PASSWORD:

Change Password Screen

7. Use the numeric keypad to enter the new password. The password will display as asterisks.

10 Main Menu

Wide Format Copy System User Guide 123

NOTE: The valid range for passwords is 0 - 65535. If the existing password or an invalid password is entered, an error message will be displayed. The new password must be entered again.

8. Press the Enter key to confirm the new password. The CHANGE PASSWORD screen will instruct you to re-enter the new password.

CHANGE PASSWORD RE-ENTER NEW PASSWORD:

Change Password Re-Enter Password Screen

9. Use the numeric keypad to re-enter the new password. The password will display as asterisks.

10. Press the Enter key to confirm the re-entry. You will be returned to the SYSTEM ADMINISTRATION menu screen. The new password is now effective. The old password is no longer valid.

Security Settings Scan-to-FTP: Scanned images can be transferred to 16 remote FTP destinations. The scanned images are not stored on the Controllers hard drive. The FTP feature is located on the Sample Mode screen.

Scan-to-Net: At most installations, users have the ability to recall the last image scanned (that was not sent to an FTP destination) and all the settings associated with that image. The recalled image can then be printed without the need to scan from the original document.

Security concerns at certain installations, however, might require that the image recall feature be disabled. The SECURITY SETTINGS option of the System Administration menu allows the system administrator to enable or disable the image recall feature. The default setting is ENABLED.

To enable/disable the image recall feature:

1. Select the Menu key.

2. Access the SYSTEM ADMINISTRATION menu.

3. Press the Next key until SECURITY SETTINGS is highlighted.

4. Press the Enter key to select SECURITY SETTINGS. The SECURITY SETTINGS screen is displayed.

SECURITY SETTINGS IMAGE RECALL: ENABLED

Security Settings Screen

10 Main Menu

124 Wide Format Copy System User Guide

5. Press the Previous or Next key to highlight the desired response, ENABLED or DISABLED.

6. Press the Enter key to confirm your selection.

7. Press the Exit key to return to the SYSTEM ADMINISTRATION menu screen.

Diagnostics menu The DIAGNOSTICS option of the Main Menu contains the following menu choices:

NOTE: Some of the scanner diagnostics listed below require a password to access and are performed only by a Customer Service Engineer.

USAGE METERS - Enables you to view usage information for documents scanned and media printed.

CLEAR USAGE - Enables the Customer Service Engineer to reset to zero the usage value for documents scanned. The diagnostic password is required for this function.

SCANNER DIAGNOSTICS - Provides a sub-menu of Scan System diagnostic routines. Some of these routines are accessible by both the operator and the Customer Service Engineer, but should only be accessed by an operator when directed to do so by Service. Access to these tests has been given to enable some preliminary diagnostics to be done by phone before a Customer Service Engineer is dispatched. Others are accessible by the Service Engineer only and require the entry of the diagnostic password.

INSTALLATION TEST PRINT - Enables the Customer Service Engineer to make a copy of the test print to assist in diagnosing the Scan System.

PASSWORD - Enables the Customer Service Engineer to enter the password for access to password-protected diagnostic functions.

To access the DIAGNOSTICS menu:

1. Press the Menu key. The MAIN MENU screen is displayed.

2. Press the Next key until DIAGNOSTICS is highlighted.

3. Press the Enter key to select DIAGNOSTICS. The DIAGNOSTICS menu screen is displayed. The black arrows indicate the menu contains more options than are visible. The selected option is highlighted.

DIAGNOSTICS USAGE METERS CLEAR SCANNER USAGE SCANNER DIAGNOSTICS

Diagnostics Menu

4. Press the Previous or Next key to scroll through the list of options.

5. When the desired option is highlighted, press the Enter key to select the option. The menu or screen for the selected option is displayed.

10 Main Menu

Wide Format Copy System User Guide 125

Usage Meters Select the USAGE METERS option of the DIAGNOSTICS menu to view the total system usage for documents scanned and media printed.

To view area and media usage:

1. Press the Menu key. The MAIN MENU screen is displayed.

2. Press the Next key until DIAGNOSTICS is highlighted.

3. Press the Enter key to select DIAGNOSTICS. The DIAGNOSTICS menu screen is displayed.

4. Press the Enter key to select USAGE METERS. The USAGE METERS screen is displayed.

The USAGE METERS screen provides Scan System area usage and media usage. Scan System area usage is measured in square units. Media usage is measured in both linear and square units. Units are displayed as either feet or meters depending on the display units selected for the Scan System. Refer to "Localization" in the "Main Menu" section for complete information about setting the display units.

Below is an example of the USAGE METERS screen. In the example, the units are displayed as meters.

USAGE METERS SCANNER (F2): 11 MEDIA LINEAR 307 MEDIA AREA 670

Usage Meters Screen

5. When finished viewing the usage information, press the Exit key to return to the DIAGNOSTICS menu screen.

Clear Scanner Usage The CLEAR SCANNER USAGE option of the DIAGNOSTICS menu is for use by the Customer Service Engineer only. It requires the entry of the diagnostic password. It allows the Customer Service Engineer to reset to zero the usage value for documents scanned.

Scanner Diagnostics The SCANNER DIAGNOSTICS option of the DIAGNOSTICS menu provides a sub-menu of the following choices:

IMAGE PATH - Enables you to validate the operation of the image processing (IP) card and the image bar.

SCAN BAR - Enables you to calibrate the response of the scan bar.

FULL SYSTEM TEST - Enables you to run all applicable tests on the Scan System to determine if it is working properly.

WRITE NVR - Enables the Customer Service Engineer to modify the contents of the non-volatile memory of the Scan System. The diagnostic password is required for this function.

10 Main Menu

126 Wide Format Copy System User Guide

RESET NVR DEFAULTS - Enables the Customer Service Engineer to reset the NVR values to the factory default values. The diagnostic password is required for this function.

SCANNER RELIABILITY METER - Enables you to gather data about the usage of the scanning mechanism.

SCANNER FAULTS (ORDERED) - Enables you to view the entries in the internal Scanner Fault Log.

FAULTS (COUNTS) - Enables you to view the last cleared faults.

CLEAR SCANNER FAULT LOG - Enables the Customer Service Engineer to erase the contents of the Scanner Fault Log. The diagnostic password is required for this function.

CLEAN CALIBRATION ZONE - Enables you to quickly move the calibration surface to the cleaning position.

COMPONENT TESTS - Provides a sub-menu of Scanner component diagnostic routines. Some of these routines are accessible by both the operator and the Customer Service Engineer. Others are accessible by the Customer Service Engineer only and require the entry of the diagnostic password.

READ NVR - Enables you to examine the contents of the non-volatile RAM (NVR).

To access the SCANNER DIAGNOSTICS menu:

1. Press the Menu key. The MAIN MENU screen is displayed.

2. Press the Next key until DIAGNOSTICS is highlighted.

3. Press the Enter key to select DIAGNOSTICS. The DIAGNOSTICS menu screen is displayed.

4. Press the Next key until SCANNER DIAGNOSTICS is highlighted.

5. Press the Enter key to highlight SCANNER DIAGNOSTICS. The SCANNER DIAGNOSTICS menu screen is displayed. The black arrows indicate that the menu contains more options than are visible. The selected option is highlighted.

SCANNER DIAGNOSTICS IMAGE PATH SCAN BAR FULL SYSTEM TEST

Scanner Diagnostics Screen

6. Press the Previous or Next key to scroll through the list of options.

7. When the desired option is highlighted, press the Enter key to select the option. The menu or screen for the selected option is displayed.

10 Main Menu

Wide Format Copy System User Guide 127

Image Path Select the IMAGE PATH option to validate the operation of the image processing (IP) card and the image bar.

To run the IMAGE PATH diagnostic:

1. Press the Menu key. The MAIN MENU screen is displayed.

2. Press the Next key until DIAGNOSTICS is highlighted.

3. Press the Enter key to select DIAGNOSTICS. The DIAGNOSTICS menu screen is displayed.

4. Press the Next key until SCANNER DIAGNOSTICS is displayed.

5. Press the Enter key to select SCANNER DIAGNOSTICS. The SCANNER DIAGNOSTICS menu screen is displayed.

6. Press the Enter key to select IMAGE PATH. The IMAGE PATH screen is displayed.

IMAGE PATH

BOARD ID: 2 STATUS: 0

BAR1: 0 BAR2: 0

BAR3: 0 ALL: 0

Image Path Screen When you enter the IMAGE PATH screen, the status field for all tests contains a "0." After a few seconds, the results of the tests are displayed. A test result with no failure displays as PASS. A test result with a failure displays a failure code. If a failure code is displayed, call for service.

7. Press the Exit key to return to the SCANNER DIAGNOSTICS menu screen.

Scan Bar Select the SCAN BAR option to calibrate the response of the scan bar.

To run the SCAN BAR diagnostic:

1. Press the Menu key. The MAIN MENU screen is displayed.

2. Press the Next key until DIAGNOSTICS is highlighted.

3. Press the Enter key to select DIAGNOSTICS. The DIAGNOSTICS menu screen is displayed.

4. Press the Next key until SCANNER DIAGNOSTICS is displayed.

5. Press the Enter key to select SCANNER DIAGNOSTICS. The SCANNER DIAGNOSTICS menu screen is displayed.

6. Press the Next key to highlight SCAN BAR.

7. Press the Enter key to select SCAN BAR. The SCAN BAR screen is displayed.

10 Main Menu

128 Wide Format Copy System User Guide

SCAN BAR CALIBRATION TEST

PRESS START TO BEGIN

Scan Bar Screen 8. Press the Start key to begin the test. While the test is executing, the bottom display

line changes to RUNNING.

At the completion of the test, the test result is displayed. A test result with no failure displays as PASSED. A test result with a failure displays as FAILED followed by ERROR CODE: and a hexadecimal value between 0 and FF. If a failure code is displayed, call for service.

9. Press the Exit key to return to the SCANNER DIAGNOSTICS menu screen.

Full System Test Select the FULL SYSTEM TEST option to run all applicable tests on the Scan System to determine if it is working properly.

To run the FULL SYSTEM TEST diagnostic:

1. Press the Menu key. The MAIN MENU screen is displayed.

2. Press the Next key until DIAGNOSTICS is highlighted.

3. Press the Enter key to select DIAGNOSTICS. The DIAGNOSTICS menu screen is displayed.

4. Press the Next key until SCANNER DIAGNOSTICS is displayed.

5. Press the Enter key to select SCANNER DIAGNOSTICS. The SCANNER DIAGNOSTICS menu screen is displayed.

6. Press the Next key until FULL SYSTEM TEST is highlighted.

7. Press the Enter key to select FULL SYSTEM TEST. The FULL SYSTEM TEST screen is displayed.

FULL SYSTEM TEST A) B) C) D) E) F)

G) H) I)

PRESS START TO BEGIN

Full System Test Screen Nine sub-tests are included in the system test. Each letter on the screen corresponds to a sub-test as follows:

a) Post Test 5 NVM (Non Volatile Memory) Verification

b) Post Test 6 Motor Communications

c) Post Test 7 SCVM Code Checksum

d) Post Test 8 SCVM (Scan System Virtual Memory) Load and Functional Test

10 Main Menu

Wide Format Copy System User Guide 129

e) Post Test 9 Pixel Magic Interface

f) Post Test A Pixel Magic Internal

g) Post Test B Video Path

h) Post Test C 24 VDC (Volts Direct Current) Power Supply Test

i) Post Test D Lamp

8. Press the Start key to begin the system test. While the tests are executing, the bottom display line changes to RUNNING.

At the completion of the tests, the test results are displayed. If a sub-test is successful, a P is displayed. If a sub-test fails, an F is displayed. If an F is displayed, the test has failed and service is required.

9. Press the Exit key to return to the SCANNER DIAGNOSTICS menu screen.

Write NVR The WRITE NVR option is for use by the Customer Service Engineer only and requires the entry of the diagnostic password. It allows the Customer Service Engineer to modify the contents of the non-volatile memory of the Scan System.

Reset NVR Defaults The RESET NVR DEFAULTS option is for use by the Customer Service Engineer only and requires the entry of the diagnostic password. It allows the Customer Service Engineer to reset the NVR values to the factory default values.

Scanner Reliability Meter Select the SCANNER RELIABILITY METER option to view the current value of the usage meter maintained by the Scan System. The meter counts and displays the number of linear feet since the Scan System Fault Log was last cleared. The number of linear feet between fault occurrences is an indication of the reliability of the Scan System.

To run the SCANNER RELIABILITY METER diagnostic:

1. Press the Menu key. The MAIN MENU screen is displayed.

2. Press the Next key until DIAGNOSTICS is highlighted.

3. Press the Enter key to select DIAGNOSTICS. The DIAGNOSTICS menu screen is displayed.

4. Press the Next key until SCANNER DIAGNOSTICS is displayed.

5. Press the Enter key to select SCANNER DIAGNOSTICS. The SCANNER DIAGNOSTICS menu screen is displayed.

6. Press the Next key until SCANNER RELIABILITY METER is highlighted.

7. Press the Enter key to select SCANNER RELIABILITY METER. The SCANNER RELIABILITY METER screen is displayed.

The Scanner usage meter is intended for gathering data about the reliability of the scanning mechanism. This meter measures linear usage only. Units are displayed as either feet or meters depending on the display units selected for the machine. Refer to Localization in the Main Menu section for complete information about setting the display units.

Below is an example of the SCANNER RELIABILITY METER screen. In the example, the units are displayed as feet.

10 Main Menu

130 Wide Format Copy System User Guide

SCANNER RELIABILITY LINEAR SCAN (FT): 5678 COLOR (FT): 0

Scanner Reliability Screen

8. Press the Exit key to return to the SCANNER DIAGNOSTICS menu screen.

Scanner Faults (Ordered) Select the SCANNER FAULTS (ORDERED) option to view the entries in the internal Scanner Fault Log.

To run the SCANNER FAULTS (ORDERED) diagnostic:

1. Press the Menu key. The MAIN MENU screen is displayed.

2. Press the Next key until DIAGNOSTICS is highlighted.

3. Press the Enter key to select DIAGNOSTICS. The DIAGNOSTICS menu screen is displayed.

4. Press the Next key until SCANNER DIAGNOSTICS is displayed.

5. Press the Enter key to select SCANNER DIAGNOSTICS. The SCANNER DIAGNOSTICS menu screen is displayed.

6. Press the Next key until SCANNER FAULTS (ORDERED) is highlighted.

7. Press the Enter key to select SCANNER FAULTS (ORDERED). The SCANNER FAULTS (ORDERED) screen is displayed.

The first line of the display contains the value of the internal Scanner Reliability Meter reading when the log was last cleared. If the log has never been cleared, the value is set to zero. This line scrolls with the log data.

The second and third lines contain the log entry information in columnar format. The first column indicates the log entry number. The second column indicates the fault code recorded in the log. The third column is the value of the internal Scanner Usage Meter at the time the fault was detected.

Below is an example of the SCANNER FAULTS (ORDERED) screen.

SCANNER FAULTS (ORDERED) LAST CLEARED: 2001 01 01-02 2476 02 01-03 2402

Scanner Faults (Ordered) Screen

8. Use the Previous or Next key to scroll through the listing.

The entries are presented three to a screen. You can view all valid entries in the Scanner Fault Log from this screen. Empty log entries are not displayed.

9. When finished viewing the fault data, press the Exit key to return to the SCANNER DIAGNOSTICS menu screen.

10 Main Menu

Wide Format Copy System User Guide 131

Scanner Faults (Count) Select the SCANNER FAULTS (COUNT) option to view the last cleared faults.

To run the SCANNER FAULTS (COUNTS) diagnostic:

1. Press the Menu key. The MAIN MENU screen is displayed.

2. Press the Next key until DIAGNOSTICS is highlighted.

3. Press the Enter key to select DIAGNOSTICS. The DIAGNOSTICS menu screen is displayed.

4. Press the Next key until SCANNER DIAGNOSTICS is displayed.

5. Press the Enter key to select SCANNER DIAGNOSTICS. The SCANNER DIAGNOSTICS menu screen is displayed.

6. Press the Next key until SCANNER FAULTS (COUNTS) is highlighted.

7. Press the Enter key to select SCANNER FAULTS (COUNTS). The SCANNER FAULTS (COUNTS) screen is displayed.

The first line of the display contains the value of the internal Scanner Reliability Meter reading when the log was last cleared. If the log has never been cleared, the value is set to zero. This line scrolls with the log data.

The second and third lines contain the log entry information in columnar format. The first column indicates the log entry number. The second column indicates the fault code recorded in the log. The third column is the value of the internal Scanner Usage Meter at the time the fault was detected.

Below is an example of the SCANNER FAULTS (COUNTS) screen.

SCANNER FAULTS (COUNTS) LAST CLEARED: 2001 01 01-02 2476 02 01-03 2402

Scanner Faults (Counts) Screen

8. Use the Previous or Next key to scroll through the listing.

The entries are presented three to a screen. You can view all valid entries in the Scanner Fault Log from this screen. Empty log entries are not displayed.

9. When finished viewing the fault data, press the Exit key to return to the SCANNER DIAGNOSTICS menu screen.

Clear Scanner Fault Log The CLEAR SCANNER FAULT LOG option is for use by the Customer Service Engineer only and requires the entry of the diagnostic password. It allows the Customer Service Engineer to erase the contents of the Scanner Fault Log.

10 Main Menu

132 Wide Format Copy System User Guide

Clean CAL Zone The CLEAN CAL ZONE (Clean Calibration Zone) provides the user with a quick way to move the Calibration Motor to the cleaning position. There are two selections CLEANING POSITION AND HOME POSITION.

CLEAN CAL ZONE POSITION: CLEANING POSITION

Clean Cal Zone Screen

Component Tests The COMPONENT TESTS option of the SCANNER DIAGNOSTICS menu provides a sub-menu of the following menu choices:

MOTOR SPEED - Enables the Customer Service Engineer to adjust the Scan System motor speed and correct magnification errors in the process direction. The diagnostic password is required for this function.

LEAD EDGE/TRAIL EDGE - Enables you to execute the lead edge/trail edge diagnostic.

SENSORS - Enables you to display the current state of the Scan System optical paper sensors and the thick document sensor.

MOTOR COMMUNICATIONS - Enables a document motor communications loopback test to assist in diagnosing a Scan System problem.

DOCUMENT MOTOR - Enables you to stop and start the document handler motor.

LAMP - Enables you to turn the lamp on and off and receive a feedback from the illumination sensor.

CALIBRATION MOTOR - Enables you to test the calibration zone motor.

To access the COMPONENT TESTS menu:

1. Press the Menu key. The MAIN MENU screen is displayed.

2. Press the Next key until DIAGNOSTICS is highlighted.

3. Press the Enter key to select DIAGNOSTICS. The DIAGNOSTICS menu screen is displayed.

4. Press the Next key until SCANNER DIAGNOSTICS is highlighted.

5. Press the Enter key to highlight SCANNER DIAGNOSTICS. The SCANNER DIAGNOSTICS menu screen is displayed.

6. Press the Next key until COMPONENT TESTS is highlighted.

7. Press the Enter key to select COMPONENT TESTS. The COMPONENT TESTS menu screen is displayed. The black arrows indicate that the menu contains more options than are visible. The selected option is highlighted.

10 Main Menu

Wide Format Copy System User Guide 133

COMPONENT TESTS MOTOR SPEED LEAD EDGE/TRAIL EDGE SENSORS

Component Tests Screen

8. Press the Previous or Next key to scroll through the list of options.

9. When the desired option is highlighted, press the Enter key to select the option. The screen for the selected option is displayed.

Motor Speed The MOTOR SPEED option is for use by the Customer Service Engineer only and requires the entry of the diagnostic password. It allows the Customer Service Engineer to adjust the Scan System motor speed and correct magnification error in the process direction.

Lead Edge/Trail Edge Select the LEAD EDGE/TRAIL EDGE option to execute the lead edge/trail edge adjustment diagnostic.

To run the LEAD EDGE/TRAIL EDGE diagnostic:

1. Press the Menu key. The MAIN MENU screen is displayed.

2. Press the Next key until DIAGNOSTICS is highlighted.

3. Press the Enter key to select DIAGNOSTICS. The DIAGNOSTICS menu screen is displayed.

4. Press the Next key until SCANNER DIAGNOSTICS is displayed.

5. Press the Enter key to select SCANNER DIAGNOSTICS. The SCANNER DIAGNOSTICS menu screen is displayed.

6. Press the Next key until COMPONENT TESTS is highlighted.

7. Press the Enter key to select COMPONENT TESTS. The COMPONENTS TESTS menu screen is displayed.

8. Press the Enter key to select LEAD EDGE/TRAIL EDGE. The LEAD EDGE/TRAIL EDGE ADJUSTMENT screen is displayed.

LEAD EDGE/TRAIL EDGE ADJUSTMENT

PRESS START TO BEGIN

Lead Edge/Trail Edge Adjustment Screen

9. Insert a black sheet (8.5 X 11) of paper into the Scan System.

10. Press the Start key to begin the diagnostic. When the diagnostic completes, the last line of the display is replaced with a status line indicating PASS or FAIL. The last line

10 Main Menu

134 Wide Format Copy System User Guide

may also display as NO RESPONSE FROM SCANNER if the Scan System does not process the request within the timeout period.

11. Press the Enter key to return to the COMPONENT TESTS menu screen.

Sensors Select the SENSORS option to display the current state of the Scan System optical paper sensors, calibration home sensor, and the thick document sensor.

To display the status of the sensors:

1. Press the Menu key. The MAIN MENU screen is displayed.

2. Press the Next key until DIAGNOSTICS is highlighted.

3. Press the Enter key to select DIAGNOSTICS. The DIAGNOSTICS menu screen is displayed.

4. Press the Next key until SCANNER DIAGNOSTICS is displayed.

5. Press the Enter key to select SCANNER DIAGNOSTICS. The SCANNER DIAGNOSTICS menu screen is displayed.

6. Press the Next key until COMPONENT TESTS is highlighted.

7. Press the Enter key to select COMPONENT TESTS. The COMPONENTS TESTS menu screen is displayed.

8. Press the Enter key to select SENSORS. Depending on the Document Feed-in Tray configuration, a SENSORS screen is displayed. The screen below is with the Productivity Tray. When a sensor is activated the icon O is filled in.

SENSORS

INPUT: O

EXIT: O HOME: O

REGISTER: O

THICK: O

O O O O O O O O O O

Sensors Screen 9. To check the status of the optical paper sensors:

a) Raise the Thickness Lever to enable an 8.5 X 11 sheet of paper to be inserted into the Scan System.

b) Insert the sheet of paper centered on the Scan System and slowly push the paper into the Scan System to check the INPUT, REGISTER, and EXIT sensors.

The sensors are located underneath the top cover. The photo below shows the location of each of the sensors on the Document Feed Tray.

10 Main Menu

Wide Format Copy System User Guide 135

Sensor Locations on the Wide Format Scan System

A: Left Oversize Document Sensor D: Register

B: Exit E: Input

C: Right Oversize Document Sensor F Discrete Width Sensors (Four on left and four on right)

c) Observe the Display. When the sensor is activated the icon O is filled in.

d) Move the sheet of paper fully to the left and right to check the LEFT and RIGHT sensors.

10. To check the status of the thick document sensor:

a) Raise the Thick Document Lever. When the sensor is activated the icon O is filled in.

b) When finished viewing the status of the thick document sensor, lower the Thick Document Lever.

11. To check the status of HOME sensor.

a) Raise the Document Handler just enough to access the Calibration Roll drive gear and still be able to see the Display.

b) Rotate the Calibration Roll one full revolution. The status will change from NO to YES if the sensor is okay.

D

A

B

C

E

F F

10 Main Menu

136 Wide Format Copy System User Guide

A: Calibration Roll Drive Gear

12. Press the Exit key to return to the COMPONENT TESTS menu screen.

Motor Communications The MOTOR COMMUNICATIONS test is for use by the Customer Service Engineer only. This test allows the Customer Service Engineer or user, if directed by the Service Engineer, to run a motor communications loopback test to assist in diagnosing a Scan System problem.

Document Motor This option allows you to stop and start the document handler motor. When you select this option, the DOCUMENT MOTOR screen is displayed.

To run the DOCUMENT MOTOR diagnostic:

1. Press the Menu key. The MAIN MENU screen is displayed.

2. Press the Next key until DIAGNOSTICS is highlighted.

3. Press the Enter key to select DIAGNOSTICS. The DIAGNOSTICS menu screen is displayed.

4. Press the Next key until SCANNER DIAGNOSTICS is displayed.

5. Press the Enter key to select SCANNER DIAGNOSTICS. The SCANNER DIAGNOSTICS menu screen is displayed.

6. Press the Next key until COMPONENT TESTS is highlighted.

7. Press the Enter key to select COMPONENT TESTS. The COMPONENTS TESTS menu screen is displayed.

8. Press the Next key until DOCUMENT MOTOR is highlighted.

9. Press the Enter key to select DOCUMENT MOTOR. The DOCUMENT MOTOR screen is displayed.

10 Main Menu

Wide Format Copy System User Guide 137

DOCUMENT MOTOR MOTOR: OFF SPEED: .125

DIRECTION: FORWARD

Document Motor Screen

10. Turn the motor on.

a) Press the Previous or Next key to highlight MOTOR.

b) Press the Enter key to confirm your selection.

c) Press the Previous or Next key to select ON. The choices are ON and OFF.

d) Press the Enter key to confirm your selection.

11. Select the motor speed.

a) Press the Previous or Next key to highlight SPEED.

b) Press the Enter key to confirm your selection.

c) Press the Previous or Next key to select the desired motor speed. The choices are .125, .250, .500, .750, 1, 1.5, 2, 3 and 4.

d) Press the Enter key to confirm your selection.

12. Select the motor direction.

a) Press the Previous or Next key to highlight DIRECTION.

b) Press the Enter key to confirm your selection.

c) Press the Previous or Next key to select the desired motor direction. The choices are FORWARD and REVERSE.

d) Press the Enter key to confirm your selection.

13. Press the Start key to activate the motor.

14. Press the Exit key to return to the COMPONENT TESTS menu screen.

Calibration Motor Select the CALIBRATION MOTOR option to set the calibration zone motor.

To run the CALIBRATION MOTOR diagnostic:

1. Press the Menu key. The MAIN MENU screen is displayed.

2. Press the Next key until DIAGNOSTICS is highlighted.

3. Press the Enter key to select DIAGNOSTICS. The DIAGNOSTICS menu screen is displayed.

4. Press the Next key until SCANNER DIAGNOSTICS is displayed.

5. Press the Enter key to select SCANNER DIAGNOSTICS. The SCANNER DIAGNOSTICS menu screen is displayed.

6. Press the Next key until COMPONENT TESTS is highlighted.

7. Press the Enter key to select COMPONENT TESTS. The COMPONENTS TESTS menu screen is displayed.

10 Main Menu

138 Wide Format Copy System User Guide

8. Press the Next key until CALIBRATION MOTOR is highlighted.

9. Press the Enter key to select CALIBRATION MOTOR. The CALIBRATION MOTOR screen is displayed.

CALIBRATION MOTOR: OFF

FUNCTION: ROTATE

Calibration Screen

10. Press the Previous or Next key to select FUNCTION.

11. Press the Enter key to select FUNCTION.

12. Press the Previous or Next key to highlight the desired function. The choices are GO TO WIDTH, GO TO CALIBRATE, GO TO HOME, FIND HOME, and ROTATE.

13. Press the Enter key to confirm your selection.

14. Press the Previous or Next key to highlight MOTOR.

15. Press the Enter key to confirm your selection.

16. Press the Previous or Next key to highlight ON. The choices are ON and OFF. The requested operation will execute.

If a GO TO or FIND function has been selected, the MOTOR field will be automatically set to OFF when the MOTOR field is once again selected. If the ROTATE function has been selected, the motor will run continuously until you set the MOTOR field to OFF.

NOTE: If the Scan System encounters a failure accessing the calibration motor function, the fourth line of the display will read "FAILURE CODE:" followed by a two-digit hexadecimal number. The fourth line may also display NO RESPONSE FROM SCANNER if the Scan System does not respond to the test request.

17. Press the Exit key to return to the Component Tests menu screen.

Read NVR The READ NVR option allows the examination of the contents of the non-volatile RAM (NVR). The service center may ask you to provide this information when calling for service.

To run the READ NVR diagnostic:

1. Press the Menu key. The MAIN MENU screen is displayed.

2. Press the Next key until DIAGNOSTICS is highlighted.

3. Press the Enter key to select DIAGNOSTICS. The DIAGNOSTICS menu screen is displayed.

4. Press the Next key until SCANNER DIAGNOSTICS is displayed.

5. Press the Enter key to select SCANNER DIAGNOSTICS. The SCANNER DIAGNOSTICS menu screen is displayed.

6. Press the Next key until READ NVR is highlighted.

10 Main Menu

Wide Format Copy System User Guide 139

7. Press the Enter key to select READ NVR. The READ NVR screen is displayed. An "xx" displays for all the NVR values.

READ NVR 00 -07: xx xx xx xx xx xx xx xx 08 - 0F: 10-17: 18-1F:

xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx

PRESS START TO BEGIN Read NVR Screen

8. Press the Start key to display the actual values.

9. Press the Previous or Next key to scroll through the values. There are 16 rows of values in all.

10. Press the Exit key to return to the SCANNER DIAGNOSTICS screen.

Password The PASSWORD option of the DIAGNOSTICS menu is for use by the Customer Service Engineer only. It allows the Customer Service Engineer to enter the password for access to password-protected diagnostic functions.

10 Main Menu

140 Wide Format Copy System User Guide

This page has been intentionally left blank.

Wide Format Copy System User Guide 141

11 Job Accounting

Job Accounting NOTE: The JOB ACCOUNTING feature is an optional feature on the Wide Format Copy System,

requiring a Feature Key to activate it. If you obtain this feature, the System Administrator can enable it at any time on the Wide Format Copy System by sending a special feature key file to the Printer. Once the feature is enabled, it remains enabled (even following upgrades to the system software). Contact your XEROX sales representative for ordering information.

Overview JOB ACCOUNTING is a SYSTEM ADMINISTRATION menu option. Access to it is restricted to the system administrator and requires the entry of the system administration password.

The JOB ACCOUNTING option allows Scan System and Printer usage to be recorded in user defined account numbers. Usage is expressed as the area (not the length) of the media scanned or used.

Job Accounting for the Scan System is controlled through the Scan System Control Panel. For the Wide Format Copy System 510 Series, 6204, and 721P, Job Accounting for the Printer can be set from either the Printer Control Panel or the Web-based Print Management Tool. For the Wide Format Copy System 6030/6050/6050A, Job Accounting for the Printer can be set from the Web Printer Management Tool only.

The Web Printer Management Tool consists of special Web pages located in the Controller. They are accessible through either the Microsoft Internet Explorer or the Netscape browsers. Version 4.0 or higher is required for proper results. Other Web browsers are not supported and may or may not work correctly.

Job Accounting can be set on the Scan System or Printer to one of three modes. The modes are ENABLED, OPTIONAL, and DISABLED.

The Scan System and Printer share a common job based accounting database referred to as the FreeFlow Accxes Account Management Tool. This Account Management Tool is composed of two components, an external accounting software package, installed on an Administrative workstation, and the job log file that is created on the Controller. The Account Management Tool creates all accounts, assigns the user IDs, gathers all the account data, manages all the accounts, and provides account reports.

NOTE: For full information on the new job accounting refer to the Account Management Tool help files.

11 Job Accounting

142 Wide Format Copy System User Guide

Job Accounting Mode Menu The JOB ACCOUNTING MODE menu allows the system administrator to access the function for enabling or disabling the Job Accounting Mode at the Scan System. Access is restricted to the System Administrator and requires the entry of the system administration password. It provides a sub-menu of the following choices:

JOB ACCOUNTING MODE

MODE: DISABLED

Job Accounting Mode Screen

The job accounting modes are as follows:

ENABLED - all jobs require a System Administrator assigned valid account number,

OPTIONAL - a System Administrator assigned valid account number is optional for any job

DISABLED - jobs do not require an account number.

To access the Job Accounting menu:

1. Select the Menu key.

2. Select System Administration > Job Accounting Mode

3. Press the Previous or Next key to scroll through the list of options.

4. When the desired option is highlighted, press the Enter key to select the option. The menu or screen for the selected option is displayed.

Submitting Jobs Job Accounting is enabled or disabled on the Scan System and the Printer independently. Job submission from either device depends on the Job Accounting mode set for the device.

From the Scan System Control Panel If Job Accounting is ENABLED, the following screen is displayed:

PLEASE ENTER USER:

Job Accounting Please Enter User Id Screen

NOTE: If Job Accounting Mode is enabled as OPTIONAL, the phrase OR PRESS ENTER will display at the bottom of the screen. No USER ID is required. Press Enter to continue.

11 Job Accounting

Wide Format Copy System User Guide 143

You must enter the User ID code assigned to you by the System Administrator. The Account ID can be alphanumeric. To enter a numeric account, press a numeric key once. To enter an alpha character, press the numeric key associated with the desired letter. Press the numeric key twice to get the first letter, three times for the second letter, etc. Pressing a key six to eight times will provide the lower case version of the respective letter. Pressing the Next key moves the cursor to the right, which will add a blank space or allow entry of a character. Pressing the Previous or C/CA keys move the cursor to the left deleting the character.

Then press ENTER to display the ACCOUNT screen and enter the account number assigned to you using the numeric keys. Once you do so, the READY screen is displayed. You can now scan and print copies.

PLEASE ENTER ACCOUNT:

Job Accounting Please Enter Account Id Screen

If Job Accounting Mode is OPTIONAL, the above screen will not be displayed. In either case, the READY screen is displayed after you press the Enter key. You can now scan and print copies.

If you entered a valid account number, all usage is charged to that account and is also accumulated under Generic User ID and Account ID code. If you did not enter an account number, usage is accumulated only in the System Account under Generic User ID and Account code.

For both the ENABLED and OPTIONAL modes, if you enter an invalid account, an error message indicated below is displayed. You cannot access the READY screen if an invalid number is entered.

ERROR: INVALID USER OR ACCOUNT

Job Accounting Error Screen

Over the Network When Job Accounting Mode is enabled the system examines the incoming job for a valid account number. If none is found, the job is rejected, and an error page is printed.

NOTE: The print drivers and the FreeFlow Accxes Client Tools (ACT) software all have a feature that allows insertion of a job accounting number. Refer to the help files for these software products for details.

If Job Accounting is optionally ENABLED, remote print jobs will be printed whether or not they have a valid account number. If a valid account number is present, the job will be charged to the user account and also accumulated to a system Generic User Id and Account Code. If no account number is present, the job is charged to a system Generic User Id and Account Code. This is the same as when Job Accounting is DISABLED.

11 Job Accounting

144 Wide Format Copy System User Guide

Terminating Use Under an Account Once a valid job account number has been entered from the Scan System Control Panel, all use of the Wide Format Copy System Scan System is charged to that account. All usage continues to accumulate to that account until one of the following occurs:

You press the Exit key while either the READY screen or a fault screen is displayed.

The FEATURE timer times out due to no activity. The default value is 5 minutes, but this value can be changed. Refer to "TIMERS" in the "Main Menu" section for information about changing the value.

When an account is no longer in use, the PLEASE ENTER ACCOUNT screen is displayed.

NOTE: To avoid incorrect accounting, always ensure that the PLEASE ENTER USER screen is displayed before leaving the Wide Format Copy System for the next operator. Press the Exit key to obtain this screen.

Wide Format Copy System User Guide 145

12 Cleaning and Maintenance - Scan System

Cleaning and maintenance - Scan System For the Scan System to do its best job, the Platen Glass, Document Drive Rolls, Backer Roll, Calibration Strip, and Document Feed Tray must be kept clean. This requires some daily and monthly cleaning and maintenance activities.

Daily activities:

Clean the Platen Glass, Document Drive Rolls, and Backer Roll. See the Cleaning the Platen Glass and Document Drive Rolls section on the next page.

Inspect the Document Feed Tray and clean as required.

Monthly activities:

Clean the Calibration Strip. See the "Cleaning the Calibration Strip" section.

Inspect the Platen Glass for chips and scratches. If the Platen Glass is chipped or scratched, and these defects are visible in the scanned images, call XEROX service.

12 Cleaning and Maintenance Scan System

146 Wide Format Copy System User Guide

The following illustration depicts the Scan System components that require cleaning.

A: Platen Glass D: Document Drive Rolls (front)

B: Backer Roll E: Document Feed Tray

C: Document Drive Rolls (rear)

Cleaning the Platen Glass, Document Drive Rolls, and Backer Roll

Perform the following steps daily:

1. Open the Top Cover.

2. Dampen a clean, lint-free towel (600S4372) with platen glass cleaning fluid (Xerox 43P81).

3. Wipe the Platen Glass with the towel.

4. Visually inspect the Platen Glass to ensure that all dirt, glue, and other residue have been removed.

5. Place a small amount of the cleaning fluid on the towel and clean the front and rear Document Drive Rolls. Rotate the Rolls as you clean them to ensure that the entire roll surface is clean.

6. Place a small amount of the cleaning fluid on the towel and wipe the white Backer Roll.

NOTE: The Backer Roll is located on the underside of the Top Cover. The Backer Roll may rotate as you clean it. This is normal behavior.

7. Close the Top Cover.

A

B

C D

E

12 Cleaning and Maintenance Scan System

Wide Format Copy System User Guide 147

Cleaning the Calibration Strip Perform the following steps monthly:

1. Press the Menu key, then scroll to the Diagnostic and press the Enter key.

Scroll to CLEAN CAL ZONE and press the Enter key.

Press the Enter key to select CLEANING POSITION.

NOTE: The Top Cover must be closed while running this test.

2. Raise the Top Cover.

3. Inspect the Calibration Strip.

4. Place a small amount of platen glass cleaning fluid (Xerox 43P81) on a clean, lint- free towel (600S4372) and clean the Calibration Strip.

5. Lower the Top Cover.

6. Press the Enter key to select HOME POSITION.

7. Press the Exit key to exit the CLEAN CAL ZONE.

8. Press the Menu key to return to the READY screen. The Calibration Strip automatically returns to its home position.

12 Cleaning and Maintenance Scan System

148 Wide Format Copy System User Guide

This page has been intentionally left blank.

Wide Format Copy System User Guide 149

13 Problem Solving

Problem Solving This section contains a problem-solving table and an error message table for help in resolving problems with the Wide Format Scan System.

Identify the problem you are experiencing and follow the step(s) indicated in the table for fixing the problem. If the procedures do not restore normal Scan System operation, call for service. For help in solving problems with the Printer or the Printer media, refer to the applicable Printer Operator Manual.

Problem Solving Table Table 3. Problem Solving Table

Problem First solution to try Second solution to try Third solution to try

Power on

The Exposure Lamp does not illuminate when the Scan System is switched on.

Ensure that the Power Cord is connected to the Scan System and to the correct power source.

Check that the Power On/Off Switch is in the on (I) position.

Call for Service.

The Scan System Control Panel continuously displays a clock face and the System does not initialize.

Ensure that the IEEE 1394 cable is connected to both the Scan System and the Controller. Check that the cable was not forced in the connector incorrectly.

For all controllers, except the YKE, YKE-N, and FRX, and LVX ensure that the DDS option is set to Enabled. NOTE: For the 6030/6050/6050A Printers, you can change this setting from either the CONTROLLER CONFIGURATION screen of the Printer Control Panel, or in the Web Printer Management Tool, select Configuration > Printer > Printer Setup > DDS Enabled. Wait 30 seconds. Then power the system off then on (rebooted). For the 721P Printer, this

13 Problem Solving

150 Wide Format Copy System User Guide

Problem First solution to try Second solution to try Third solution to try

change can be made from the Web Printer Management Tool only.

Constant Scanner NOT READY message

Lift the Document Handler Switch off the Scan System Switch off the Printer/Controller Switch on the Scan System and wait for the display to indicate P Switch on the Controller, then the Printer.

Call for Service.

Corrupted or unclear messages after powering the Scan System off, then on.

Ensure the System was powered off, then on correctly: Switch off the Scan System. Switch off the Printer/Controller. Switch on the Scan System and wait for the display to indicate P. Switch on the Controller then Printer.

Call for Service.

Scan System control

The Scan System does not scan when a document is inserted.

Press the Start key or enable AUTOSCAN. See "Scan System control" in the "Main Menu" section for more information.

The Scan System measures the width of the original incorrectly. The copy is either wider than the original, or the copy is clipped.

Clean the Platen Glass. Open the Upper Document Transport. Look for a row of 10 holes across the Feed-in Shelf next to the Platen Glass. If the holes are present, press the Menu key and scroll to CONFIGURATION>SCAN SYSTEM CONTROL> MODE and check if mode is set to PRODUCTIVITY. If it is, ensure that the media series setting for the PRODUCTIVIY matches the media series being used in the Printer. If the media series matches, set the MODE to AUTOWIDTH/AUTOCENTER and call for service.

Turn AUTOWIDTH off. See "Scan System Control" in the "Main Menu" section for more information.

Run the diagnostic test to validate which width detection sensors are working correctly. Select Main button > Diagnostics > Scanner Diagnostics > Component Tests > Sensors.

When the Scan System is set to exit to the front, the document is difficult to remove from the Scan System.

Raise the Thick Document Lever to release the document. Be sure to lower the Thick Document Lever before making the next

Set the Scan System to exit to the rear. See "Scan System Control" in the "Main Menu section for more information.

13 Problem Solving

Wide Format Copy System User Guide 151

Problem First solution to try Second solution to try Third solution to try

copy/scan.

Document feed

The Scan System will not accept a thin document (less than .03 in (1 mm) thick).

Ensure that both the Scan System and the Printer are powered up and initialized. Ensure that the Thickness Lever is adjusted correctly for the document being scanned.

If the thin document has a torn or dog-eared lead edge, try feeding a different edge first.

Insert the document in a document carrier.

he Scan System will not accept a thick document.

Ensure that both the Scan System and the Printer are powered up and initialized.

Set the Thick Document Lever to its next higher setting. Thick documents may require operator assistance.

The Scan System measures the width of the original incorrectly. The copy is either wider than the original or the copy is clipped.

Refer to this documents section Cleaning the Platen Glass, Document Drive Rolls and Backer Roll. Wipe the Document Feed Tray with anti-static fluid. See the second item above in Scan System Control.

Turn the AUTOWIDTH off. See Scan System Control in the Main Menu section for more information.

When the Scan System is set to exit to the front, the document is difficult to remove from the Scan System.

Raise the Thick Document Lever to release the document. Be sure to lower the Thick Document Lever before making the next copy/scan.

Set the Scan System to exit to the rear. See Scan System Control in the Main Menu section of this document for more information.

Width detection failed when scanning transparent documents. Width sensors in most cases will not detect transparent documents.

Enter the document width. Turn AUTOWIDTH off and refer to Scan System Control in the Main Menu.

Not Ready Media Jam Refer to Cleaning the Platen Glass, Document Drive Rolls, and Backer Roll. Wipe the Document Feed Tray with anti-static fluid.

If the document is folded, worn or damaged, use a document carrier or try feeding a different edge.

For thick documents, set the Thick Document Lever to its next higher setting. Thick documents may require operator assistance.

The Scan System does not position the document correctly before scanning.

Ensure that you are inserting the document correctly. Center the document between the marks on the Document Feed Tray. Smoothly insert the document into the feed mechanism so that the lead edge of the document is against the rollers before the Scan System begins to stage the document.

Check the operation of the optical paper sensors. See "Sensors" in the "Main Menu" section for more information.

Image quality

13 Problem Solving

152 Wide Format Copy System User Guide

Problem First solution to try Second solution to try Third solution to try

Vertical lines and streaks are visible in the copy.

Clean the Platen Glass.

Visible document edges on the copy.

Try a lighter Contrast setting.

ark spots or smudges appear on the copy.

Clean the Platen Glass. Inspect the original and clean it if necessary.

Adjust the Copy setting for best image quality.

The copy image is too light. Adjust the Copy setting for best image quality.

Rotate the original 90 degrees.

The image density on the copy varies from light to dark.

Rotate the original 90 degrees.

Adjust the Copy setting for best image quality.

Copies made in Photo mode have geometric patterns.

Set the Original, Type to Normal and the Background Suppression to Off.

Set Original, Type to Line and Background Suppression off.

Try a lighter Contrast setting.

Fine lines on the original do not appear on the copy when the image size is reduced.

Enable the LINE MODE LINE PRESERVATION option. See "Imaging" in the "Main Menu" section for more information.

Adjust the Copy setting for best image quality.

Gray areas appear in the copy at the location of creases or folds in the original document.

Refold the document in the reverse direction to flatten the creases or folds.

Error messages

An error message is displayed on the Scan System Control Panel.

Locate the message in Table 8, "Error Code Messages," in this section and perform the corrective action indicated.

13 Problem Solving

Wide Format Copy System User Guide 153

Error Code Messages Table Table 4. Error Code Messages Table

Error message Probable cause Corrective action

40000001: ERROR ACCOUNTING DISK FULL

The Job Log File size has reached the maximum space allocated for it.

Contact your System Administrator.

40000002: ERROR The number of Job Records in the Job Log File has reached the maximum as defined by the FreeFlow Accxes Account Management Tool.

Contact your System Administrator.

CONTROLLER FAULT - 50000001

The Controller has developed a "memory is full" internal fault. Large documents using Auto Reduction/Enlargement or Auto- Rotate may cause this fault. Also, Photo and Mixed/Custom modes require significantly more memory than Line mode.

Remove the document. Press Start to print the job.

CONTROLLER FAULT - 50000002

The Controller has developed a memory is full internal fault. Large documents using Auto Reduction/Enlargement or Auto Rotate may cause this fault. Also, Photo and Mixed/Custom modes require significantly more memory than Line mode.

Remove the document. Wait for previous scans to finish printing. End the current set or print it if a set is in progress. Rescan the document.

CONTROLLER FAULT - 50000003 CONTROLLER FAULT - 50000004 CONTROLLER FAULT - 50000005

A task controlling the Scan System received an unrecognized request from the task controlling the Scan System control panel.

Power off the System. Check that all cables are connected correctly. Power on the System. See the "Powering off the System" and "Powering on the System" sections for more information.

CONTROLLER FAULT - 50000007

A software problem was encountered in controlling the Scan System.

Power off and power on the System. See the "Powering off the System" and "Powering on the System" sections for more information.

CONTROLLER FAULT - 50000008 - DOCUMENT JAM

A document jam has occurred in the Scan System.

Remove the jammed document. Scan the document again.

CONTROLLER FAULT - 50000011 - SCANNED IMAGE LOST

FreeFlow Accxes firmware supports a maximum of 128 active jobs in the printer queue. Scans made after the maximum were refused and a scan error was declared.

Allow the jobs in the queue to print, and then rescan the document. FreeFlow Accxes firmware reserves 8 jobs for Scan-to-Net and copy jobs. This provides sufficient capability for scans and copy jobs even when there is a high volume of print jobs on the network.

13 Problem Solving

154 Wide Format Copy System User Guide

SCAN SYSTEM FAULT - 5000000B - CHECK SCAN SYSTEM VERIFY SCAN SYSTEM IS POWERED AND PROPERLY CONNECTED

A fault has occurred in communicating with the Scan System.

Check that the IEEE 1394 cable is properly connected at both ends. Check that the Scan System is still connected to the AC power and is still switched on. Power off and power on the System. See the "Powering off the System" and "Powering on the System" sections for more information.

CONTROLLER FAULT - 50000012 - MEMORY FULL CONTROLLER FAULT - 5000013 - MEMORY FULL

The file system or memory is full. Retrieve or delete some documents to create more space. Then rescan the document.

CONTROLLER FAULT - 50000014 - MEMORY FULL

Documents were scanned too fast. Memory is full.

Wait for previously scanned documents to be processed and stored on the hard disk. Then scan the current document again.

CONTROLLER FAULT - 50000015

An error occurred saving the scanned image to a disk.

Do not scan until the interrupted job is finished. Check that the SCSI cable or IEEE 1394 cable is connected correctly.

CONTROLLER FAULT 50000017

FTP file transfer failed. On the Web Printer Management Tool, check the FTP destination settings by selecting Configuration > Scanner.

SCAN SYSTEM MESSAGE: DISK IMAGE OVERWRITE IN PROGRESS

When a user selects the On-Demand Image Overwrite on the Web Printer Management Tool, the FreeFlow Accxes controller will reboot, causing the message on the printer and scan system during the reboot.

The message will be gone after the reboot sequence updates the scan system in the normal fashion.

SCAN SYSTEM FIRMWARE VERSION FAULT -50000020

Scan System firmware must be at version 3.2.6 or higher to support scan functions.

Update the Scan System firmware.

SCAN SYSTEM FAULT - COMPLEX DOCUMENT

An error occurred during processing due to the complexity of the image that the document contains.

Rescan the document.

WARNING: xxxx The image submitted for printing is corrupted or does not conform to the standards for the format.

Recreate the image and try again.

LL codes appear intermittently while documents are scanned

Intermittent Scan System and/or software problems.

Power the system off then on. If the problem persists, call for service.

Wide Format Copy System User Guide 155

14 Specifications

Specifications Speed 510

Series 721P 6030/6050/6050A 6204 6279

2 inches per second

4 inches per second

standard standard standard standard

1 inch per second color

optional optional optional optional

7.33 inches per second*

standard

* Requires Turbo III Speed Enhancement feature key, PUN, YKE, YKE-N, FRX, and LVX Controller running version 9.0 or higher software, Wide Format Scan System firmware version 3.0.7A or higher.

Input Document Maximum document: 42" x 100 feet (1.07m x 30.5 m) Maximum Scan Width: 36" (914 mm) Minimum document: A size 8.5 x 11 (216mm x 279mm) A4 size (210mm x 297mm) Document Thickness: 0.0023 to 0.50 " (0,06mm to 13mm) Thick Document Weight: 6 lbs (2.72 kg) max.

Scan System Resolution

Copying: 200, 300, 400, 600 dots per inch Scan-to-Net 75, 100, 200, 300, 400, 600 dots per inch

Magnification: 25% to 400% in 0.1%

increments

14 Specifications

156 Wide Format Copy System User Guide

Temperature Minimum: 55 F (10 C) Maximum: 90 F(32 C)

Humidity: 20% - 80%

Maximum Elevation: 0 - 6560 feet

0 - 1.995 km

Heat Emission

Running: 690 BTU/hr

Power Consumption

Standby: 130 W Running: 200 W

Electrical Requirements

Voltage (AC): 100 - 120 VAC 200 - 240 VAC Current: 4 amps 3 amps

Frequency: 50/60 Hz

Audible Noise

Standby: 33.7 dBA Running: 52.1 dBA Impulse: 56.4 dBA

Wide Format Copy System User Guide 157

15 Appendices

Appendix 1: Scanning Resolutions and Speeds Table 5 below shows the minimum and maximum scanning speeds for a 36 inch (914 mm) wide document in Line, Mixed, and Photo modes at various resolutions.

NOTE: Speeds are given in inches per second (IPS) and centimeters per second (cm/s).

NOTE: Thick documents are scanned at a maximum speed of 4.00 IPS/10.16cm/s in all Modes.

Table 5. Scanning resolutions and speeds

Turbo II Turbo III 2 IPS Mode DPI Pixel

Depth Min IPS/ cm/s

Max IPS/ cm/s

Min IPS/ cm/s

Max IPS/ cm/s

Min IPS/ cm/s

Max IPS/ cm/s

Line (copy or scan mode)

400 1 bit 4.00/10.16 4.00/10.16 7.00/17.78 7.00/17.78 2.00/5.08 4.00/10.16

Line (scan mode) 300 1 bit 4.00/10.16 4.00/10.16 4.00/10.16 4.00/10.16 2.00/5.08 4.00/10.16 Line (scan mode) 200 1 bit 8.00/20.32 8.00/20.32 8.00/20.32 8.00/20.32 4.00/10.16 4.00/10.16 Line (scan mode) 100 1 bit 8.00/20.32 8.00/20.32 8.00/20.32 8.00/20.32 4.00/10.16 4.00/10.16 Normal and Photo only (scan mode)

75 4 bit 2.00/5.08 4.00/10.16 2.00/5.08 4.00/10.16

Photo (scan mode) 400 8 bit 0.5/1.27 4.00/10.16 4.00/10.16 4.00/10.16 0.5/1.27 4.00/10.16 Photo (scan mode) 300 8 bit 1.00/2.54 4.00/10.16 4.00/10.16 4.00/10.16 1.00/2.54 4.00/10.16 Photo (copy or scan mode)

200 8 bit 2.00/5.08 8.00/20.32 8.00/20.32 8.00/20.32 2.00/5.08 4.00/10.16

Photo (scan mode) 100 8 bit 8.00/20.32 8.00/20.32 8.00/20.32 8.00/20.32 4.00/10.16 4.00/10.16

15 Appendices

158 Wide Format Copy System User Guide

Appendix 2: Paper Sheet Sizes Paper sizes supported by the 510 Series, 721P, 6030/6050/6050A, 6204, and 6279 Printers and the Controller with Firmware 9.1 or higher are shown in Table 6. The Media types supported by your printer and the FreeFlow Accxes firmware can be checked on the Web Printer Management Tool by selecting Defaults > Media > Media Defaults > Media Type. Available roll sizes for each supported media type can be quickly and easily checked from the supplies page of the XEROX website at www.xerox.com.

Table 6. Printer paper sizes

Paper size Dimension 510 Series 721P 6030/6050/ 6050A

6204 6279

ISO A0 841 x 1189 mm X X X X X

ISO A1 594 x 841 mm X X X X X

ISO A2 420 x 594 mm X X X X X

ISO A3 297 x 420 mm X X X X X

ISO A4 210 x 297 mm X X X X X

ISO B1 707 x 1000 mm X X X X X

ISO B2 500 x 707 mm X X X X X

ISO B3 353 x 500 mm X X X X X

ISO B4 250 x 353 mm X X X X X

ANSI A 8.5 x 11 (215.9 x 279.4 mm)

X X X X X

ANSI B 11 x 17 in. (279.4 x 431.8 mm)

X X X X X

ANSI C 17 x 22 in. (431.8 x 558.8 mm)

X X X X X

ANSI D 22 x 34 in. (558.8 x 863.6 mm)

X X X X X

ANSI E 34 x 44 in. (863.6 x 1117.6 mm)

X X X X X

Architectural A 9 x 12 in. (228.6 x 304.8 mm)

X X X X X

Architectural B 12 x 18 in. (304.8 x 457.2 mm)

X X X X X

Architectural C 18 x 24 in. (457.2 x 609.6 mm)

X X X X X

Architectural D 24 x 36 in. (609.6 x 914.4 mm)

X X X X X

Architectural E 36 x 48 in. (914.4 x 1219.2 mm)

X X X X X

Architectural 30" 30 x 42 in. (76.2 x 1066.8 mm)

X X X X X

JIS B4 257 x 364mm X X X X

JIS B3 364 x 515mm X X X

JIS B2 515 x 725mm X X X

JIS B1 728 x 1030mm X X X

15 Appendices

Wide Format Copy System User Guide 159

Appendix 3: Paper Roll Sizes Table 7 below shows roll sizes supported by the 510 Series, 721P, 6030/6050/6050A, 6204, and 6279 Printers.

Table 7. Printer roll sizes

Roll size Width 510 Series 721P 6030/6050/ 6050A

6204 6279

ISO Roll A0 841 mm X X X X X

ISO Roll A1 594 mm X X X X X

ISO Roll A2 420 mm X X X X X

ISO Roll A3 297 mm X X X X X

Roll 891 891 mm - X - - -

Roll 900 900 mm X X X - -

ANSI Roll 11 11 in. X X X X X

ANSI Roll 17 17 in. X X X X X

ANSI Roll 22 22 in. X X X X X

ANSI Roll 34 34 in. X X X X X

ARCH Roll 12 12 in. X X X X X

ARCH Roll 15 15 in. X

ARCH Roll 18 18 in. X X X X X

ARCH Roll 24 24 in. X X X X X

ARCH Roll 30 30 in. X X X X X

ARCH Roll 36 36 in. X X X X X

ISO B3 353 mm X X X X X

ISO B2 500 mm X X X X X

ISO B1 707 mm X X X X X

JIS B3 364 mm X X X

JIS B2 515 mm X X X

JIS B1 728 mm X X X

Sp. A2 440 mm X X

Sp. A1 620 mm X - X X X

750 mm X - X

860 mm X - X X X

Sp. A0 880 mm X X X X X

15 Appendices

160 Wide Format Copy System User Guide

Appendix 4: LED Status Indicators The PUN Controller has four LED status indicators as shown in Table 8 below.

Table 8. Controller LED status indicators

LED Number Color Indicated Condition

LED 1 Green "Ready." Indicates that the Controller is powered up and ready to process incoming jobs.

LED 2 Green "Busy." Indicates that the Controller is busy processing a job.

LED 3 Yellow "Mismatch." Indicates that a media mismatch, which may be blocking the print queue, has occurred. This also displays when the Controller's Accounting disk is full, or when the Controller has reached its Accounting record limit. Check the Web Printer Management Tool's Main Page to determine the problem.

LED 4 Red "Attention." Indicates that a Printer or Finisher fault has occurred. May indicate a paper jam, out of toner condition, out of media condition, or a communications problem with one of the devices.

During power-on self test (POST), the firmware will light LEDs 2, 3, and 4. After POST has successfully completed, LEDs 2, 3, and 4 will be switched OFF, and LED 1 will be switched ON. If POST did not successfully complete, all 4 LEDs will be switched OFF (i.e., they will be unlit).

15 Appendices

Wide Format Copy System User Guide 161

Appendix 5: Main Menu Structure Appendix 7 shows the Main Menu structure. The menu tree below shows the top level of the Main Menu. The pages that follow contain menu trees for each of the four top-level options.

Main Menu

Configuration System AdministrationSystem Information Diagnostics

The menu tree below shows the Configuration option structure of the Main Menu.

Configuration

Localization Language Display units

Control Panel Copy Options Image Enhancement

Timers Power Saver

Beeper Text Default Mode

Color IQ Normal Mode Dynamic Background Removal

Feature Printer Interrupt File Deletion

Media Series

Custom Media Formats

Custom R/E Preset

Imaging

Auto-Rotate Reduction Line Preservation

Autoscan Document Return Mode: Autowidth/Auto

Center Manual Width Autowidth Productivity

Scanner Control

Power Saver delay

15 Appendices

162 Wide Format Copy System User Guide

The menu tree below shows the System Information option structure of the Main Menu.

System Information

System Description Configuration Prints Recent Fault List

Scanner Controller Control Panel Printer Finisher

Copier Configuration Printer Configuration Printer Settings All Configuration Prints

The menu tree below shows the structure of the System Administration option of the Main Menu.

Change Password Security Settings

System Administration

PasswordJob Accounting Mode

Change Password File System

List by Directory Delete Images Delete All Images

Image Recall

The menu tree below shows the Diagnostics option structure of the Main Menu.

Diagnostics

Usage Meters Clear Scanner Usage Scanner

Diagnostics Installation Test

Print Password Scanner (Ft2) Media Linear Media Area

Scanner (Ft2) Image Path Scan Bar Full System Test Write NVR Reset NVR Defaults Scanner Reliability Meter Scanner Faults (Ordered) Scanner Faults (Counts) Clear Scanner Fault Log Clean Calibration Zone Read NVR

Component Test Motor Speed Lead Edge/Trail Edge Sensors Motor Communications Document Motor Lamp Calibration Motor

Wide Format Copy System User Guide 163

16 Index

ADAPTIVE CONTRAST, 108 Auto, 23 Auto Media Source, 24 AUTO ROTATE, 106 Automatic edge detection and document

centering, 42 AUTOSCAN, 57, 110, 111 AUTOWIDTH, 58, 110 AUTOWIDTH /AUTOCENTER, 42 AUTOWIDTH/AUTOCENTER, 58, 110 Background Suppression, 54, 94 Background Suppression option, 22 Batch key, 82 beeper, 101 BEST COMPRESSION, 53, 54 BEST IQ, 53, 54 blueprint, 45 C/CA (Clear/Clear All) key, 28 C/CA key, 95 CAD_GIS, 53 CALIBRATION MOTOR, 132 CALIBRATION MOTOR option, 137 Calibration Roll Drive Gear, 136 Calibration Screen, 138 CHANGE PASSWORD, 117 CHANGE PASSWORD option, 122 Change Password Screen, 122 checkplot, 80 CLEAN CAL ZONE, 132 Clean Cal Zone Screen, 132 CLEAN CALIBRATION ZONE, 126 Cleaning and maintenance - Scanner, 145 Cleaning the Calibration Strip, 147 Cleaning the Platen Glass and Document Drive

Rolls, 146 CLEAR LAST IMAGE, 95 Clear Scanned Image Screen, 95 CLEAR SCANNER FAULT LOG, 126 CLEAR SCANNER FAULT LOG option, 131 CLEAR SCANNER USAGE, 124

Clearing the scanned images, 95 Color, 21, 52 Color Enablement Feature Key, 8 Color lithograph, 45 Color map, 45 Color photograph, 45 Compact Organizer, 13 Compact Stacker, 13 COMPONENT TESTS, 126 COMPONENT TESTS option, 132 Component Tests Screen, 133 COMPRESSION (JPEG selected), 53, 54 COMPRESSION (TIFF selected), 52 CONFIGURATION, 99 Configuration menu, 100 Configuration menu options, 161 CONFIGURATION menu:, 100 CONFIGURATION PRINTS, 112 CONFIGURATION PRINTS option, 115 Configuration Screen, 100, 115 CONTROL PANEL, 100 CONTROL PANEL option, 101 Control Panel Screen, 102 CONTROLLER FAULT, 153 Controller Power Switches, 31 Controller Screen, 113 Copier Configuration Screen, 115 Copier Parameters and Images Screen, 70 copies, making, 57 COPY LENGTH, 49, 106 COPY mode, 91 COPY MODE, 48 Copy Mode Sample, 88 Copy option, 23, 55 COPY OPTIONS, 100, 102 COPY OPTIONS menu, 102 Copy Options Screen, 103 copy the same size as the original document, 60 CROSSFOLD OPTIONS, 79 CUSTOM MEDIA FORMATS, 105

16 Index

164 Wide Format Copy System User Guide

Custom Media Formats Screen, 105, 111 Custom Output Format Screen, 17 CUSTOM R/E PRESETS option, 106 Custom R/E Presets Screen, 106 Decimal key, 28 DEFAULT, 53 Default media settings, 59 DELETE ALL IMAGES, 118 DELETE ALL IMAGES option, 121 Delete All Images Screen, 121 DELETE IMAGE option, 120 DELETE IMAGES, 118 Delete Images Screen, 120 Delete Last Job Screen, 71 DELETE TEMPLATE option, 74 Delete Template Screen, 74 Deleting the Last Job, 71 DIAGNOSTICS, 99 Diagnostics menu, 124 Diagnostics Menu, 124 Diagnostics Menu options, 162 DIAGNOSTICS option, 124 display units, 101 Document Exit Slot, 12 Document Feed Tray, 11 Document Handler, 10 DOCUMENT MOTOR, 132 Document Motor Screen, 137 Document quality, 41 DOCUMENT RETURN, 57, 110 DYNAMIC BACKGROUND REMOVAL, 49 DYNAMIC BACKGROUND REMOVAL, 41 Enlargement, 106 Enter key, 26 Error Code Table, 153 Error Screen - Job Accounting, 143 Exit key, 26 Faded line/text drawing, 45 FASTEST, 49 Feature Keys, 8 FILE DELETION, 109 File Format, 51 file system, 96 FILE SYSTEM, 117 FILE SYSTEM option, 96, 118 File System Screen, 119 film, vellum/tracing, 45 Finisher key, 64, 75 Finisher Not Available Error Message

Screen, 76 Finisher Screen, 76, 114 fixed copy size, 61 FOLD PROGRAM, 77 Fold Program Screen, 77 Folder, 63 FORMAT, 50, 52

FORWARD prints, 81 FTP, 27, 89, 123 FTP Transfer Failed Screen, 92 FULL SYSTEM TEST, 125 FULL SYSTEM TEST option, 128 Full System Test Screen, 128 Graphical Display, 14 HFT Controller, 31 IEEE 1394 Cable and Connector, 12 IMAGE ENHANCEMENT feature, 107 Image Enhancement Screen, 23, 49, 108 IMAGE ENHANCEMENTS, 100 Image Entering the Scanner Diagram, 84 IMAGE PATH, 125 Image Path Screen, 127 Image Quality, 19, 47, 58 Image Quality Area, 19 Image Quality Illustration, 59 IMAGING option, 106 Imaging screen, 49 Imaging Screen, 107 Immediate Image Overwrite, 69 INDEX, 52 INDEX ED, 52 INSTALLATION TEST PRINT, 124 INTELLIGENT TITLE BLOCK, 79 Invalid Mode screen, 20 INVERT option, 87 Job Accounting, 141 JOB ACCOUNTING MODE, 117, 142 Job Accounting Mode Screen, 142 JOB ACCOUNTING option, 118 Job Parameters and Images Screen, 71 Job Parameters Recalled Screen, 73, 75 Job Parameters Saved Option, 75 Job Parameters Saved Screen, 72 JOB TEMPLATES, 69 JOB TEMPLATES option, 71 Job Templates Screen, 72 JUSTIFICATION, 83 JUSTIFICATION option, 85 Justification Screen, 85 LAMP, 132 language, 101 LAST JOB, 69 LAST JOB option, 69 Last Job Screen, 70 LEAD EDGE/TRAIL EDGE, 132 Lead Edge/Trail Edge Adjustment Screen, 133 LEAD EDGE/TRAIL EDGE option, 133 LED Status Indicators, 160 Line, 21, 50 Line mode, 48 Line, photo or mixed original on film, 45 LIST BY DIRECTORY, 118 List by Directory Screen, 119

16 Index

Wide Format Copy System User Guide 165

LOCALIZATION, 100 LOCALIZATION option, 101 Localization Screen, 101 long document, 65 Main Menu, 99 Main menu options, 161 Main Menu Screen, 100 MANUAL, 58 Manual mode, 17 Manual mode, 24 Manual Reduction/Enlargement Screen, 25 MANUAL WIDTH, 110 MARGIN OPTIONS, 78 Margin Options Screen, 78 MARGINS, 83 margins for an image, 84 MARGINS option, 83 Margins Selection Screen in Transform

Menu, 84, 85 MAXIMUMCOPY LENGTH, 49, 106 MEDIA FORMATS, 105 Media Selection, 15 Media Selection Area, 15 MEDIA SERIES option, 104 Media Series Screen, 104 Menu key, 26 MIRROR option, 86 Mode key, 26 MOTOR COMMUNICATIONS, 132 MOTOR COMMUNICATIONS test, 136 MOTOR SPEED, 132 MOTOR SPEED option, 133 Navigation keys, 14 Navigational Keys and Graphical Display Area,

26 Next key, 26 Normal, 20 NORMAL, 53, 54 Normal mode, 48, 49 NORMAL MODE, 49 Numeric Keypad, 28 Numerical Key pad, 14 Operating in SCAN mode, 94 Option Keys section, 14 Original, Type, 20, 48 OUTPUT BIN option, 80 Output Bin Screen, 80 Output Format option, 17 OVERLENGTH OPTIONS, 77 Overlength Options Screen, 77 oversized documents, 65 PACKBITS, 52 PALETTE, 53 paper sizes, 158 password, 117 PASSWORD, 124

PASSWORD option, 139 PERCEPTUAL, 53 Photo, 21, 51 Photo mode, 48 Please Enter Account Id Screen, 143 Please Enter Directory Screen, 92 Please Enter User Id Screen, 142 Power Cord, 12 Power off the Controller and the Printer, 40 power on the XEROX WIDE FORMAT COPY

SYSTEMS, 30 Power On/Off Switch, 12, 31 Power On/Off Switch Photo, 40 POWER SAVER, 100 POWER SAVER option, 109 Power Saver Screen, 110 Power Switch Photo, 31 Preparing documents, 44 Preset, 17, 18 Preset (factory default), 25 Preset Output Format screen, 18 Preset Output Format Screen, 61 Preset Reduction/Enlargement Screen, 25 Preview, 50 PREVIEW, 50, 52 Printer Configuration Screen, 116 PRINTER INTERRUPT, 109 Printer Interrupt key, 68 Printer Screen, 113 Printer Settings Screen, 116 Problem solving, 149 PRODUCTIVITY, 110 PRODUCTIVITY ANSI, 58 PRODUCTIVITY MODE, 42 PUNCH OPTIONS, 78 Punch Options Screen, 78 READ NVR, 126 READ NVR option, 138 Read NVR Screen, 139 Ready to Build Set Screen, 81 Ready to Copy Screen, 27, 40, 48, 59, 64, 77,

99 Ready to Print Set Screen, 81 Ready to Scan Screen, 27, 93 READY TO SCAN screen, 93 RECALL FACTORY DEFAULTS, 69, 75 RECALL LAST JOB, 69, 70 RECALL TEMPLATE option, 73 Recall Template Screen, 73 RECENT FAULT LIST, 112 RECENT FAULT LIST option, 114 Recent Fault List Screen, 114 Reduce/Enlarge, 24, 94 Reduce/Enlarge Area, 24 Reduction, 106 REDUCTION LINE PRESERVATION, 49

16 Index

166 Wide Format Copy System User Guide

REDUCTION LINE PRESERVATION, 106 RESET NVR DEFAULTS, 126 RESET NVR DEFAULTS option, 129 REVERSE prints, 81 Safety Notes, 1 Sample key, 88 Sample Mode Screen, 88 SAVE DEFAULT TEMPLATE, 69 SAVE DEFAULT TEMPLATE option, 74 SAVE TEMPLATE option, 72 Save Template Screen, 72 SCAN BAR, 125 SCAN BAR option, 127 Scan Bar Screen, 128 Scan Control keys, 14 Scan Control Keys, 29 SCAN mode, 91 Scan Mode Sample, 89 Scan Options (Color) Screen, 53, 54 Scan Options (Color) screens, 22 Scan Options (Color) Screens, 53 Scan Options (Line) Screen, 21, 50 Scan Options (Normal) Screen, 20, 50 Scan Options (Photo) Screen, 21, 51 Scanner compact components, 13 SCANNER CONTROL, 100 SCANNER CONTROL option, 110 Scanner Control Panel, 10, 14 Scanner Control Panel Photo, 14 Scanner Control Screen, 57, 111 SCANNER DIAGNOSTICS, 124 SCANNER DIAGNOSTICS option, 125 Scanner Diagnostics Screen, 126 SCANNER FAULTS (COUNT) option, 131 SCANNER FAULTS (COUNTS), 126 Scanner Faults (Counts) Screen, 131 SCANNER FAULTS (ORDERED), 126 SCANNER FAULTS (ORDERED) option, 130 Scanner Faults (Ordered) Screen, 130 SCANNER RELIABILITY METER, 126 SCANNER RELIABILITY METER option, 129 Scanner Reliability Screen, 130 Scanner Screen, 113 Scanner standard components, 10 Scanning Resolutions, 157 Scanning resolutions and speeds, 157 Scanning strategies, 45 Scanning strategies for special documents,

45 Scanning to the Network, 91 Scan-to-Net, 92 Scan-to-Net Feature Key, 8 Scan-to-Print Feature Key, 8 Security Settings, 123 SECURITY SETTINGS, 117 SECURITY SETTINGS option, 123

Security Settings Screen, 123 Selections disabled in SCAN mode, 93 SENSORS, 132 SENSORS option, 134 Sensors Screen, 134 sepia, 45 Sets Build key, 80 Sets Build Screen, 80 Source option, 16 Special features keys, 67 Special Features keys, 14 Special Features Keys, 29 Specifications, 155 Speed Enhancement T, 8 Speeds, 157 SRGB, 108 Stand, 10 Standard Organizer, 11 Standard Stacker, 12 Start key, 29 Status LED, 12 Stop key, 29 Store/Recall key, 69 Store/Recall Screen, 69 Synchro mode, 18 SYSTEM ADMINISTRATION, 99 SYSTEM ADMINISTRATION menu, 117 System Administration menu options, 162 SYSTEM ADMINISTRATION option, 117 System Administration Screen, 118 SYSTEM DESCRIPTION, 112 SYSTEM DESCRIPTION option, 112 System Description Screen, 112 SYSTEM INFORMATION, 99 System Information menu, 112 System Information menu options, 162 SYSTEM INFORMATION option, 112 System Information Screen, 112 System Screen, 118 TAB OPTIONS, 78 Tab Options Screen, 78 Template is in Use Screen, 73 Thick Document Lever, 10 TIMERS, 100 TIMERS option, 108 Timers Screen, 109 TITLE BLOCK LOCATION, 79 Title Block Location Screen, 79 TRANSFORM, 83 Transform key, 83 TRANSFORM MENU, 83 Transform Menu Screen, 83 TRANSFORM option, 86 Transform Screen, 86, 87, 88 translucent media, 45 Type Line, 50

16 Index

Wide Format Copy System User Guide 167

Type option, 16, 20, 48 Type Photo, 51 Type, Color, 52 Understanding the READY TO SCAN screen, 93 USAGE METERS, 124, 125 Usage Meters Screen, 125 WEB, 53

WIDE DOCUMENTS, 65 WIDE FORMAT SCAN SYSTEM Front View,

10 WIDE FORMAT SCAN SYSTEM Rear View, 11 Width Found for Set is XX.X Screen, 82 WRITE NVR, 125 WRITE NVR option, 129

16 Index

168 Wide Format Copy System User Guide

This page has been intentionally left blank.

Manualsnet FAQs

If you want to find out how the 6050A Xerox works, you can view and download the Xerox 6050A Scanner User Guide on the Manualsnet website.

Yes, we have the User Guide for Xerox 6050A as well as other Xerox manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The User Guide should include all the details that are needed to use a Xerox 6050A. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Xerox 6050A Scanner User Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Xerox 6050A Scanner User Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Xerox 6050A Scanner User Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Xerox 6050A Scanner User Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Xerox 6050A Scanner User Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.