Contents

Xerox iGen 150 Press Media Cart User Guide PDF

Pages 36
Year 2012
Language(s)
English en
1 of 36
1 of 36

Summary of Content for Xerox iGen 150 Press Media Cart User Guide PDF

Page 3

Operating the Xerox Production Media Cart (iGen) ... 21 Customer Caveat (Paper Stacking) ... 21 Docking the Xerox Production Media Cart with the Xerox iGen Stacker Pallet with Power Eject Kit ... 22 Lifting the Stack from the iGen Stacker ... 25 Transferring the Stack to the CP Bourg BSFEx Air Table ... 27 Offloading the Stack to a Work Table ... 29 Offloading the Stack to a Pallet ... 31

Page 5

The Production Media Cart is an optional unit that can interface with certain Xerox stackers to assist with transporting printed media from the printer stacker to work tables, pallets, or near- line/offline finishing... The Production Media Cart (Cart) uses a battery powered vertical elevation system to set the media table height and a hand crank to transfer the paper stack from the Cart...

Page 6

Cart... Unlock: Allows the Cart to roll during transport... 7... Vertical post 8... Paper table support: Joins the paper table to the vertical post... 9... Battery: Supplies the power to elevate the paper table... 10... On/Off switch: Switches the power to the Cart on or off...

Page 7

11... Battery meter: Shows the voltage of the battery... 12... Circuit breaker: If current exceeds 15 amps , circuit breaker will trip and require a reset by

Page 8

Improper operation can cause accidents... Dont take chances with incorrect or damaged equipment... Read and understand the procedures for safe operation as outlined in this manual... Do not hesitate to ask for help... Stay alert! Follow safety rules, regulations, and procedures... Avoid accidents by recognizing dangerous procedures or situations before they occur...

Page 9

become unsafe... This Cart is intended for use on smooth, level surfaces only... Do not use on ramps or grades, rough or broken floors... Do not lift with the tine tips or one tine only... Do not move the Cart without securing the paper stack with the stack clamp... Use special care when operating the Cart with paper stacks to avoid tipping, loss of load, or

Page 10

Always look in the direction of travel... Keep a clear view and when the load obstructs visibility, travel with the load lowered... Watch swing clearance when turning near walls, racks, pillars, machinery, or other obstacles... Before you leave the Cart, fully lower the paper table and set the caster locks... Do not operate the Cart at greater than 3 miles per hour... Never stand or sit on the paper table... Never sit, stand, lift, or transport any person on the paper table... Never use the Cart as a stepladder... Never operate the Cart on a moving vehicle... Never operate the Cart when any of its parts have been removed... Do not wear loose clothing such as ties and scarves, or dangling accessories such as

Page 11

Raise the Cart to full height... Listen and watch for unusual sounds or jerky motions... Lower the Cart until it is fully lowered... Listen and watch for unusual sounds or jerky

Page 12

Cleaning Use a clean cloth to clean the HOST belts... Keep the belts clean, dry and free from debris and dirt...

Page 13

The Media Cart battery should be charged if the battery meter is outside the green zone on the meter...

Page 14

4... Plug the power cord into a proper electrical outlet... 5... Charge the battery for 6-8 hours or until the light on the charger indicates that it is charged... When light is yellow, system is charging... When light turns green, battery is charged...

Page 15

Required kit Install the XPS Media Cart Stacking Surface Kit to enable docking with the XPS Stacker Install the iGen Pallet Interface Kit Install the iGen Powered Eject Kit

Page 16

Warning Do not exceed the load capacity of 160 lbs... (72... 6 kg) to avoid personal injury and damage to the Cart... 1... Position the Cart in front of the XPS Stacker after it has moved out from the printer...

Page 17

2... Set the Cart to the appropriate height... a... Locate the line on the cart post that corresponds to the stacker height (low: 210 mm;

Page 18

6... Move the Cart forward slowly until the black line on the Carts alignment tine aligns with the black line on the XPS Stacker...

Page 19

2... Gently lift up on the paper stack clamp near the clamp post to free it for rotation... Lift it high enough so that it will clear the top of the paper stack...

Page 20

3... Rotate the clamp and position it over the paper stack... 4... Gently press the clamp at the clamp post to secure it...

Page 21

Xerox Nuvera, iGen Production System Production Media Cart 17 Production Media Cart User Guide

Page 22

5... Gently lift up on the paper stack clamp near the clamp post, rotate it to one side, and rest it in the locator on the clamp post...

Page 23

1... Press the upper part of the elevation button to raise the media table height until it exceeds the height of the work table enough for the bottom of the paper stack to clear it...

Page 24

1... Press the elevation button to set the media table height until it exceeds the height of the pallet enough for the bottom of the paper stack to clear it...

Page 25

For stacking sizes that are smaller than 14 in... (355... 6 mm) in the process direction, add a single 14... 33 (363... 982 mm) wide sheet of card stock (270-300 gsm) to cover the 5-6 tine surfaces on the right side of the stacker pallet... This is to ensure adequate stacker for smaller size papers... Larger sizes, such as 11 x 17 in, 14... 33 x 20... 5 in, 14... 33 x 26 in... , do not require the additional sheet...

Page 26

a... Locate the line on the cart post that corresponds to the iGen stacker height of 103 mm... b... Press the elevation button to match the short lines on the sides to the line on the cart

Page 27

3... Roll the cart into position... Insert tang on right front leg of the media cart into the Y shaped groove of the docking bracket... Ensure that the end of the cart butts against the left side docking bracket...

Page 28

controlled emergency stop... Press button to stop... Press button 2nd time to continue... The power eject system will reset itself after an emergency stop...

Page 29

2... Gently lift up on the paper stack clamp near the clamp post to free it for rotation... Lift it high enough so that it will clear the top of the paper stack...

Page 30

26 Xerox Nuvera, iGen Production System Production Media Cart Production Media Cart User Guide

Page 31

Transferring the Stack to the CP Bourg BSFEx Air Table 1... Position the Cart in front of the CP Bourg BSFEx Air Table...

Page 32

5... Gently lift up on the paper stack clamp near the clamp post, rotate it to one side, and rest it in the locator on the clamp post...

Page 33

1... Press the upper part of the elevation button to raise the media table height until it exceeds the height of the work table enough for the bottom of the paper stack to clear it...

Page 34

3... Gently lift up on the paper stack clamp near the clamp post, rotate it to one side, and rest it in the locator on the clamp post...

Page 35

1... Press the elevation button to set the media table height until it exceeds the height of the pallet enough for the bottom of the paper stack to clear it...

Manualsnet FAQs

If you want to find out how the iGen 150 Xerox works, you can view and download the Xerox iGen 150 Press Media Cart User Guide on the Manualsnet website.

Yes, we have the Media Cart User Guide for Xerox iGen 150 as well as other Xerox manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Media Cart User Guide should include all the details that are needed to use a Xerox iGen 150. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Xerox iGen 150 Press Media Cart User Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Xerox iGen 150 Press Media Cart User Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Xerox iGen 150 Press Media Cart User Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Xerox iGen 150 Press Media Cart User Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Xerox iGen 150 Press Media Cart User Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.