Xerox SquareFold Trimmer Module Ver.1.0 Finishing Device User Guide PDF

Pages 24
Year 2008
Language(s)
English en
1 of 24
1 of 24

Summary of Content for Xerox SquareFold Trimmer Module Ver.1.0 Finishing Device User Guide PDF

Page 3

Main components ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 2 Paper path ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 3 Control panel ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 4

Page 5

Note 1: The booklet is assembled and stapled in the booklet area of the finisher; therefore, the booklet enters the SquareFold Trimmer Module already assembled... Any adjustments to the image of the original and its placement on the booklet page must be done either from the machines UI or from your print driver...

Page 6

Important!: The top covers cannot be opened during normal operation or when the machine is idle... The covers can be opened only when an indicator is lit (refer to page 4) and a jam/fault occurs within the SquareFold Trimmer Module...

Page 7

Tip: Booklets exiting/leaving the SquareFold Trimmer Module may contain trim remnants/scraps from the previously trimmed booklet... This is due to static electricity build-up and is normal... If booklets contain trim remnants/scraps, simply remove and discard them...

Page 8

Tip: If one of these indicators (1a, 1b, 1c) is lit, the top covers can be opened, and the jam/fault cleared; otherwise, during normal operation or when the machine is idle, the top covers cannot be opened... For information on jam/fault clearance, refer to page 12...

Page 9

Trimmer Mode Setting: This displays the trimmer setting in millimeters... The trimmer setting is based on the final output booklet size and is adjustable... This is discussed in more detail on page 8...

Page 10

The Square Fold Settings are found on the SquareFold Trimmer Module control panel... The settings can be switched on or off based on user preference... When the settings are switched on, you can select one of five options depending on your requirements for the finished booklet job:

Page 11

The following illustration shows two different booklets: one booklet which was square-folded and one booklet that was not square-folded...

Page 12

Note: Trim settings cannot be adjusted to remove less than 2 mm (0... 078 in... ) or more than 20 mm (0... 787 in... ) of edge material from the booklet... Adjustments less than 2 mm (0... 078 in... ) may produce poor trim quality, and adjustments greater 20 mm (0... 078 in... ) will result in no trimming to the booklet edge...

Page 13

Tip: The following table shows various scenarios using different paper weights, media types, and trim setting selections... Use this table as a guideline when selecting a trim setting for your specific job... The settings shown in the following table are provided as examples and are not meant to represent every possible job scenario; again, use this table as a guideline only...

Page 14

What is the desired size of the finished booklet? Does the booklet contain full-page images? Are you using preprinted covers with full-page images? Are you trimming the booklet? Do you need to shift any full-page images in order to ensure they fit on the finished booklet?

Page 15

Use the various selections from your applications print driver; refer to your print drivers Help information, and/or Use the various selections from the machines UI for the booklet creation and image shift features; refer to your machines user guide for more information

Page 16

Important!: The top covers cannot be opened during normal operation or when the machine is idle... The covers can be opened only when an indicator is lit (refer to page 4) and a jam/fault occurs within the SquareFold Trimmer Module...

Page 17

If the SquareFold Trimmer Module Control Panel and/or the machines UI indicate there is a still a jam, recheck the SquareFold Trimmer Module (steps 1-8)...

Page 18

If a jam/fault occurs in the SquareFold Trimmer Module, a fault code is displayed on the Control Panel... The machines UI may also display a jam/fault message... The following table provides a list of fault codes for the SquareFold Trimmer Module and also provides a list of related finisher fault codes...

Page 19

If full, empty the container and reinsert it into the SquareFold Trimmer Module... If the container is partially pulled out, push it completely in...

Page 20

A top cover is open... Open the Top Left and Right Covers of the SquareFold Trimmer Module...

Page 21

If machines UI continues to reflect a fault/jam, open the finisher and remove any jams...

Page 22

50 in... (1271... 4 mm) width x 28... 5 in... (724... 3 mm) depth x 22 in... (558... 8 mm) height

Page 24

2008 Xerox Corporation... All rights reserved... Xerox, the sphere of connectivity design, and SquareFold are trademarks of Xerox Corporation in the United States and/or other countries...

Manualsnet FAQs

If you want to find out how the Ver.1.0 Xerox works, you can view and download the Xerox SquareFold Trimmer Module Ver.1.0 Finishing Device User Guide on the Manualsnet website.

Yes, we have the User Guide for Xerox Ver.1.0 as well as other Xerox manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The User Guide should include all the details that are needed to use a Xerox Ver.1.0. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Xerox SquareFold Trimmer Module Ver.1.0 Finishing Device User Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Xerox SquareFold Trimmer Module Ver.1.0 Finishing Device User Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Xerox SquareFold Trimmer Module Ver.1.0 Finishing Device User Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Xerox SquareFold Trimmer Module Ver.1.0 Finishing Device User Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Xerox SquareFold Trimmer Module Ver.1.0 Finishing Device User Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.