Xerox Wireless adapter Adapter Installation Instructions PDF

1 of 2
1 of 2

Summary of Content for Xerox Wireless adapter Adapter Installation Instructions PDF

Ensure the "Xerox Phaser 3100MFP Documentation and

Companion Pro Software" CD is installed on your computer

Do not install the "Xerox Phaser 3100MFP WLAN" CD until

directed to do so.

1.Insert the Wireless Adapter into the MFP

2.Configuring the Wireless Adapter There are two methods of configuring the Wireless Adapter :

If you have a wireless router and want to use it then choose the Infrastructure

method, otherwise choose the Ad-Hoc method.

Infrastructure Method 1. On the Phaser 3100MFP press , select SETUP using the keys or

and confirm with OK.

2. Select WLAN using the keys or and confirm with OK.

3. Select SETUP WIZARD using the keys or and confirm with OK.

4. Select your existing wireless network name in the list using the keys or

and confirm with OK.

Note: If your network does not appear in the list, you have to select NEW

NETWORK at the end of the list and then enter SSID (the name of

your network using the numerical keypad, (32 characters maximum)

and select mode INFRA.

5. If your wireless network has a encryption key (WEP or WPA) you must

enter the key you are using in the network from the control panel. For more details see the user guide of your gateway or computer.

6. IP CONF.: MANU or IP CONF.: AUTO appears on the screen. It is recommended to use an Automatic IP Address by selecting IP

CONF.:AUTO using the keys or and confirming with OK.

If you choose to set up the system manually enter the parameters IP

ADDRESS, SUBNET MASK and GATEWAY.

7. When you press OK, the machine reboots to take into account the new

WLAN parameters. Once the network has been set up, the LED of the

Wireless Adapter should be on.

Ad-Hoc Method 1. On the Phaser 3100MFP press , select SETUP using the keys or

and confirm with OK.

2. Select WLAN using the keys or and confirm with OK.

3. Select SETUP WIZARD using the keys or and confirm with OK.

4. Select NEW NETWORK using the keys or and confirm with OK.

5. SSID appears on the screen, enter the name of your network using the numerical keypad, pressing the keys one after the other until you obtain

the name you want (32 characters maximum) and confirm with OK.

6. MODE AD-HOC or MODE INFRA appears on the screen. Select AD-HOC

MODE and confirm with OK.

7. The sub-menu CHANNEL appears, enter a figure between 1 and 11 and confirm with OK.

8. Select your encryption method, W/O Security or WEP Encryption, and confirm with OK. If you choose WEP, enter the WEP key that you wish to use on your network.

9. IP CONF.: MANU or IP CONF.: AUTO appears on the screen. It is recommended to use Automatic IP Address by selecting IP CONF.: AUTO using the keys or and confirm with OK. If you choose to set up the system manually enter the parameters IP ADDRESS, SUBNET MASK and GATEWAY.

10.You should now return to the main menu of SETUP WIZARD. When you press OK, the machine reboots to take into account the new WLAN parameters. Once the network has been set up, the LED of the Wireless Adapter should be on.

11.Open up your PC wireless connections and select your SSID name (set up earlier) and select connect. Wait until connected is displayed. This may take several minutes.

12.If your SSID name does not appear verify Ad-Hoc steps 1-12. 3.After Configuring the Wireless Adapter

1. Insert Phaser 3100MFP Wireless Adapter CD in the computer. 2. Select Yes, Next, I accept, Next and follow the instructions. Depending

on your PC configuration it may reboot. Once the reboot is complete verify the Companion Monitor is loaded (two Xerox Icons will appear on your desktop) if not retry.

3. Connect USB cable. Drivers installation will start automatically. Wait for the end of the installation.

4. Follow instructions to update the firmware of the MFP and wait for the reboot of the MFP then remove the USB cable.

4.Add the printer to the PC Wireless Networks list 1. If you used the Ad-hoc method. Depending on your PC configuration you

may have to open up your PC wireless connections and select your SSID name (set up earlier) and select Connect. Wait until connected is displayed. This may take several minutes. If you used the Infrastructure method go to step 2.

2. Double click on the Xerox Companion Monitor Icon and in the tab Device selection, select +Add. Wait for the screen to refresh. This may take several minutes

3. Select your device (i.e. MF_XXXXXXXXXXXX) from the list and select Next.

4. Depending on the Operating System of your PC and the model of your machine, choose the printer driver to install and click Next, then check the technical settings and click Next and Finish.

5. Enter a registration name for your PC, click OK and follow the instructions. 6. Select the printer you want to use on Companion monitor.

For more details: Click on the Companion Director icon on your desktop to open Companion Director. Click on the Help button to view the comprehensive user guide. see chapter PC features / Companion Monitor / Device Management / Adding a device connected to the network.

Important : Only print and scan functions are available when you use the WLAN. The WLAN adaptor and DECT are not compatible, do not use them together.

Assurez-vous que le CD Xerox Phaser 3100MFP Documentation and Companion Pro Software est install sur votre ordinateur.

Ninstallez pas le CD Xerox Phaser 3100MFP WLAN avant quil vous le soit demand.

1.Insrer ladaptateur sans fil dans la MFP

2.Configuration de ladaptateur sans fil Voici deux mthodes de configuration de ladaptateur sans fil : Si vous disposez dun routeur sans fil et que vous souhaitez l'utiliser, choisissez alors la mthode Infrastructure, sinon choisissez la mthode Ad- Hoc.

Mthode Infrastructure 1. Sur le Phaser 3100MFP, appuyez sur , slectionnez REGLAGES laide

de la touche ou et validez en appuyant sur OK. 2. Slectionnez WLAN laide de la touche ou et validez en appuyant

sur OK. 3. Slectionnez ASS. CONFIG. laide de la touche ou et validez en

appuyant sur OK. 4. Slectionnez le nom de votre rseau sans fil existant dans la liste laide

de la touche ou et validez en appuyant sur OK.

Remarque : Si votre rseau napparat pas dans la liste, vous devez slectionner NOUVEAU RESEAU la fin de la liste puis entrer SSID (le nom de votre rseau laide du clavier numrique, (32 caractres maximum) et slectionnez le mode INFRA.

5. Si votre rseau sans fil dispose dune cl de cryptage (WEP ou WPA), vous devez entrer la cl utilise sur le rseau sur le panneau de commande. Pour obtenir plus dinformations dtailles, reportez-vous au Guide utilisateur de votre passerelle ou de votre ordinateur.

6. CONF. IP : MANU ou CONF. IP : AUTO apparat lcran. Il est recommand dutiliser une adresse IP automatique en slectionnant CONF. IP : AUTO laide de la touche ou et validez en appuyant sur OK. Si vous choisissez de configurer le systme manuellement, entrez les paramtres ADRESSE IP, MSK SS RES et PASSERELLE.

7. Lorsque vous appuyez sur OK, le terminal redmarre pour prendre en compte les nouveaux paramtres WLAN. Une fois le rseau configur, la LED de ladaptateur sans fil doit tre allume.

Mthode Ad-Hoc 1. Sur le Phaser 3100MFP, appuyez sur , slectionnez REGLAGES laide

de la touche ou et validez en appuyant sur OK. 2. Slectionnez WLAN laide de la touche ou et validez en appuyant

sur OK. 3. Slectionnez ASS. CONFIG. laide de la touche ou et validez en

appuyant sur OK. 4. Slectionnez NOUVEAU RESEAU laide de la touche ou et validez

en appuyant sur OK. 5. SSID apparat lcran, saisissez le nom de votre rseau laide du

clavier numrique en appuyant successivement sur les touches jusqu lobtention du nom voulu (32 caractres maximum) et validez en appuyant sur OK.

6. MODE AD-HOC ou MODE INFRA apparat lcran. Slectionnez MODE AD-HOC et validez en appuyant sur OK.

7. Le sous-menu CANAL apparat, entrez un chiffre entre 1 et 11 et validez en appuyant sur OK.

8. Slectionnez votre mthode de cryptage, AUCUNE ou WEP, et validez en appuyant sur OK. Si vous choisissez WEP, entrez la cl WEP que vous souhaitez utiliser sur votre rseau.

9. CONF. IP : MANU ou CONF. IP : AUTO apparat lcran. Il est recommand dutiliser ladresse IP automatique en slectionnant CONF. IP : AUTO laide de la cl ou et validez en appuyant sur OK. Si vous choisissez de configurer le systme manuellement, entrez les paramtres ADRESSE IP, MSK SS RES et PASSERELLE.

10.Vous devez prsent revenir au menu principal de lASSISTANT DE CONFIGURATION. Lorsque vous appuyez sur OK, le terminal redmarre pour prendre en compte les nouveaux paramtres WLAN. Une fois le rseau configur, la LED de ladaptateur sans fil doit tre allume.

11.Activez les connexions sans fil de votre PC et slectionnez le nom de votre SSID (configur prcdemment) et slectionnez Connecter. Patientez jusqu ce que Connect saffiche. Cette opration peut prendre plusieurs minutes.

12.Si le nom de votre SSID napparat pas, vrifiez les tapes Ad-Hoc 1 12.

3.Aprs avoir configur ladaptateur sans fil 1. Insrez le CD Phaser 3100MFP Wireless Adapter dans lordinateur. 2. Slectionnez Oui, Suivant, Jaccepte, Suivant et suivez les instructions.

En fonction de la configuration de votre PC, il se peut que celui-ci redmarre. lissue du redmarrage, vrifiez que le Companion Monitor est charg (deux icnes Xerox apparatront sur votre bureau). Si ce nest pas le cas, ressayez.

3. Connectez le cble USB. Linstallation des pilotes dmarrera automatiquement. Patientez jusqu la fin de linstallation.

4. Suivez les instructions pour mettre jour le firmware de la MFP et attendez que la MFP redmarre, puis retirez le cble USB.

4.Ajouter limprimante la liste des rseaux sans fil du PC 1. Si vous avez utilis la mthode Ad-hoc. En fonction de la configuration de

votre PC, il se peut que deviez activer les connexions sans fil de votre PC et slectionner le nom de votre SSID (configur prcdemment) puis Connecter. Patientez jusqu ce que Connect saffiche. Cette opration peut prendre plusieurs minutes. Si vous avez utilis la mthode Infrastructure, passez ltape 2.

2. Double cliquez sur licne Xerox Companion Monitor et sous longlet Slection du priphrique, slectionnez +Ajouter. Patientez jusqu ce que lcran soit mis jour. Cette opration peut prendre plusieurs minutes.

3. Slectionnez votre priphrique (soit MF_XXXXXXXXXXXX) dans la liste et slectionnez Suivant.

4. En fonction du systme dexploitation de votre PC et du modle de votre terminal, choisissez le pilote de limprimante installer et cliquez sur Suivant, puis vrifiez les paramtres techniques et cliquez sur Suivant et Terminer.

5. Entrez un nom denregistrement pour votre PC, cliquez sur OK et suivez les instructions.

6. Slectionnez limprimante que vous souhaitez utiliser sur Companion monitor.

Pour obtenir plus dinformations dtailles : Cliquez sur licne Companion

Director sur votre bureau pour ouvrir Companion Director. Cliquez sur le

bouton Aide pour afficher le Guide utilisateur dans son intgralit. Reportez-

vous au chapitre Fonctions PC / Companion Monitor / Gestion des

priphriques / Ajout dun priphrique connect au rseau.

Important : Seules les fonctions dimpression et de numrisation sont

disponibles lorsque vous utilisez le WLAN. Ladaptateur WLAN et le DECT ne

sont pas compatibles, ne les utilisez pas simultanment.

Compruebe que el CD de "Documentacin del Xerox Phaser 3100MFP y del programa Companion Pro" est instalado en su ordenador.

No instale el CD "WLAN del Xerox Phaser 3100MFP" hasta que le indique que lo haga.

1.Introduzca el adaptador inalmbrico en el MFP

2.Configuracin del adaptador inalmbrico Existen dos mtodos para configurar el adaptador inalmbrico: si tiene un enrutador inalmbrico y desea utilizarlo, elija el mtodo de infraestructura, o de lo contrario, elija el mtodo Ad-hoc.

Mtodo de infraestructura 1. En el Phaser 3100MFP pulse , seleccione PARAMETROS utilizando las

teclas o y confirme con OK. 2. Seleccione WLAN utilizando las teclas o y confirme con OK. 3. Seleccione ASIS. CONFIG. utilizando las teclas o y confirme con OK. 4. Seleccione el nombre de su red inalmbrica existente en la lista, utilizando

las teclas o y confirme con OK.

Nota: Si su red no aparece en la lista, tendr que seleccionar NUEVA RED

al final de la lista y a continuacin, indicar SSID (el nombre de su

red utilizando el teclado numrico, de 32 caracteres como mximo)

y seleccione el modo INFRA.

5. Si su red inalmbrica tiene una clave de codificacin (WEP o WPA), deber indicar la clave que est utilizando en la red a partir del panel de control. Si desea ms informacin, vase la gua de usuario de la puerta de salida o del ordenador.

6. CONFIG. IP: MANU o CONF. IP: AUTO aparecer en pantalla. Se le aconseja que utilice una Direccin IP automtica seleccionando CONF. IP:AUTO utilizando las teclas o y confirmando con OK. Si elije configurar el sistema manualmente, indique los parmetros DIRECCIN IP, MSCARA DE SUBRED y GATEWAY.

7. Cuando pulse OK, la mquina se reinicia para tener en cuenta los nuevos parmetros WLAN. Una vez que haya configurado la red, la LED del adaptador inalmbrico deber estar encendida.

Mtodo Ad-Hoc 8. v y confirme con OK. 9. Seleccione NUEVA RED utilizando las teclas o y confirme con OK. 10.SSID aparece en pantalla, indique el nombre de su red utilizando el

teclado numrico, pulsando las teclas una tras la otra hasta que obtenga el nombre que desee (32 caracteres como mximo) y confirme con OK.

11.MODO AD-HOC o MODO INFRA aparece en pantalla. Seleccione MODO AD-HOC y confirme con OK.

12.Aparecer el submen de CANAL, indique un nmero entre el 1 y el 11, y confirme con OK.

13.Seleccione su mtodo de codificacin, Seguridad W/O o la CodificacinWEP, y confirme con OK. Si elije WEP, indique la clave WEP que desea utilizar en su red.

14.CONFIG. IP: MANU o CONF. IP: AUTO aparecer en pantalla. Le aconsejamos que utilice una Direccin IP automtica seleccionando CONF IP: AUTO utilizando las teclas o y confirme con OK. Si elije configurar el sistema manualmente, indique los parmetros DIRECCIN IP, MSCARA DE SUBRED y GATEWAY.

15.Ahora deber regresar al men principal del ASIS. CONFIG. Cuando pulse OK, la mquina se reinicia para tener en cuenta los nuevos parmetros WLAN. Una vez que haya configurado la red, la LED del adaptador inalmbrico deber estar encendida.

16.Abra sus conexiones inalmbricas de PC y seleccione su nombre SSID (configurado previamente) y seleccione conectar. Espere hasta que aparezca un mensaje "conectado" en pantalla. Esto podr tardar varios minutos.

17.Si su nombre SSID no aparece, compruebe las etapas 1-12 Ad-Hoc.

3.Tras configurar el adaptador inalmbrico 1. Introduzca el CD del Adaptador inalmbrico Phaser 3100MFP en el

ordenador. 2. Seleccione S, Siguiente, Acepto, Siguiente y siga las instrucciones. En

funcin de la configuracin de su PC, quizs deba reiniciarlo. Una vez que haya completado el reinicio, compruebe que el Monitor de Companion se ha cargado (aparecern dos iconos de Xerox en su escritorio), de lo contrario, intntelo de nuevo.

3. Conecte el cable USB. La instalacin de los pilotos empezar automticamente. Espere a que termine la instalacin.

4. Siga las instrucciones para actualizar el firmware del MFP y espere a que se reinicie el MFP y a continuacin, retire el cable USB.

4.Aada la impresora a la lista de redes inalmbricas del PC. 1. Si utiliz el mtodo Ad-hoc. En funcin de la configuracin de su PC, quizs

tenga que abrir sus conexiones inalmbricas de PC y seleccionar su nombre SSID (configurado previamente) y seleccionar Conectar. Espere hasta que aparezca un mensaje "conectado" en pantalla. Esto podr tardar varios minutos. Si utiliz el mtodo de Infraestructura, vaya a la etapa 2.

2. Haga doble clic en el icono del Monitor de Xerox Companion y en la pestaa Seleccin del dispositivo, seleccione+Aadir. Espere a que la pantalla se actualice. Esto podr tardar varios minutos.

3. Seleccione su dispositivo (por Ej. MF_XXXXXXXXXXXX) a partir de la lista y seleccione Siguiente.

4. En funcin del sistema operativo de su PC y del modelo de su ordenador, elija el piloto de la impresora que va a instalar y pulse en Siguiente, a continuacin, compruebe la configuracin tcnica y pulse en Siguiente y Terminar.

5. Indique un nombre de registro para su PC, pulse en OK y siga las instrucciones.

6. Seleccione la impresora que desea utilizar en el monitor de Companion.

Para ms informacin: Pulse en el icono de Companion Director ubicado en su escritorio para abrir el Companion Director. Pulse el botn de Ayuda para ver la gua de usuario al completo. Vase el captulo Funciones del PC/ Monitor Companion / Gestin del dispositivo / Aadir un dispositivo conectado a la red.

Importante: Slo las funciones de impresin y escner se encuentran disponibles cuando utiliza el WLAN. El adaptador WLAN y DECT no son compatibles, no los utilice juntos.

Printer ans scanner driver name Connection

Xerox Phaser 3100 MFP USB

Phaser 3100MFP WLAN WLAN

Nom du pilote de limprimante et du scanner

Connexion

Xerox Phaser 3100 MFP USB Phaser 3100MFP WLAN WLAN

Nombre del piloto del escner e impresora Conexin

Xerox Phaser 3100 MFP USB

Phaser 3100MFP WLAN WLAN

Wireless adapter installation instructions Instructions dinstallation de ladaptateur sans fil Instrucciones de instalacin del adaptador inalmbrico

2 5 3 xx xx xx A

GI WLAN XEROX 6 langues.fm Page 1 Vendredi, 19. dcembre 2008 3:44 15

Assicurarsi che il CD "Documentazione Xerox Phaser 3100MFP e Companion Pro Software" sia installato sul proprio computer.

Non procedere all'installazione del CD "Xerox Phaser 3100MFP WLAN" fino a quando non sia chiaramente indicato.

1.Inserire l'adattatore Wireless nel MFP

2.Configurare l'adattatore Wireless Esistono due metodi per configurare l'adattatore Wireless: Se si possiede un router wireless e o si vuole utilizzare alla scegliere il metodo Infrastruttura, altrimenti scegliere il metodo Ad hoc.

Metodo Infrastruttura 1. Sul Phaser 3100MFP premere , selezionare IMPOSTAZIONI con i tasti

o e confermare con OK. 2. Selezionare WLAN con i tasti o e confermare con OK. 3. Selezionare CONFIG. ASS. con i tasti o e confermare con OK. 4. Selezionare nell'elenco dei nomi di reti disponibili quello che interessa con

i tasti o e confermare con OK.

Nota: In caso la propria rete non appaia nell'elenco, selezionare NUOVA RETE in basso all'elenco e quindi inserire SSID (Il nome della propria rete mediante la tastiera numerica, (32 caratteri max.) e selezionare la modalit INFRA.

5. Se la propria rete wireless ha una chiave crittografica (WEP or WPA) questa deve essere inserita a partire dal pannello di configurazione in rete . Per ulteriori dettagli si vedano le istruzioni per l'uso della propria gateway o computer.

6. CONF IP: MANU o CONF. IP: AUTO appaiono sullo schermo. Si raccomanda l'utilizzo dell'indirizzo IP in modo automatico, selezionando CONF. IP: AUTO con i tasti o e confermare con OK. Se si sceglie di impostare il sistema in modo manuale, cambiare i propri parametri di rete e inserire i parametri INDIRIZZO IP, SUBNET MASK e GATEWAY.

7. Quando si preme OK, il terminale si reinizzializza per registrare i nuovi parametri WLAN. Una volta configurata la rete, la spia led della chiave USB WLAN dovrebbe essere accesa.

Metodo Ad hoc 1. Sul Phaser 3100MFP premere , selezionare IMPOSTAZIONI con i tasti

o e confermare con OK. 2. Selezionare WLAN con i tasti o e confermare con OK. 3. Selezionare CONFIG. ASS. con i tasti o e confermare con OK. 4. Selezionare NUOVA RETE con i tasti o e confermare con OK. 5. SSID appare sullo schermo, immettere il nome della rete mediante la

tastiera numerica premendo successivamente i tasti fino ad ottenere il nome voluto (32 caratteri max.) e confermare con OK.

6. MOD.AD HOC o MOD. INFRA. appare sullo schermo. Selezionare MOD. AD HOC e confermare con OK.

7. Appare il sotto menu CANALE, inserire un numero compreso tra 1 e 11 e confermare con OK.

8. Selezionare il proprio metodo Sicurezza W/O o crittografia WEP e confermare con OK. Se si sceglie WEP, inserire la chiave WEP che si sta usando sulla propria rete.

9. CONF IP: MANU o CONF. IP: AUTO appaiono sullo schermo. Si raccomanda l'utilizzo dell'indirizzo IP automatico con la selezione di CONF. IP: AUTO con i tasti o e confermare con OK. Se si sceglie di impostare il sistema in modo manuale, cambiare i propri parametri di rete e inserire i parametri INDIRIZZO IP, SUBNET MASK e GATEWAY.

10.Si dovrebbe tornare al menu principale del CONFIG. ASS.. Quando si preme OK, il terminale si reinizzializza per registrare i nuovi parametri WLAN. Una volta configurata la rete, la spia led della chiave USB WLAN dovrebbe essere accesa.

11.Aprire la connessione wireless del proprio pc e selezionare il nome SSID (impostato prima) e selezionare collegare. Attendere fino a quando venga visualizzata la connessione. Questo puo' prendere qualche minuto.

12.Se il nome SSID attribuito non apparisse, verificare i passaggi 1-12 della modalit Ad hoc.

3.Dopo aver configurato l'adattatore Wireless 1. Inserire il CD Phaser 3100MFP Wireless Adapter nel computer. 2. Selezionare Si', Seguente, Accetto, Seguente e seguire le istruzioni. A

seconda della configurazione il pc potrebbe riavviarsi. Una volta riavviato, verificare che il Companion Monitor sia stato scaricato (appariranno sul desktop due icone Xerox) altrimenti riprovare.

3. Collegare il cavo USB. L'installazione dei driver si avvia automaticamente. Attendere la fine dell'installazione.

4. Seguire le istruzioni per aggiornare il firmware del MFP e attendere il riavvio dell'MFP, quindi rimuovere il cavo USB.

4.Aggiungere la stampante all'elenco reti PC wireless 1. Se si utilizza il metodo Ad hoc. A seconda della configurazione del proprio

pc possibile che si debba aprire la connessione wireless e selezionare il nome SSID (gi impostato in precedenza) e selezionare Collega. Attendere fino a quando venga visualizzata la connessione. Questo puo' prendere qualche minuto. Se si utilizza il metodo Infrastruttura andare al passaggio 2.

2. Fare doppio clic sull'icona Xerox Companion Monitor e sulla scheda Selezione periferica, selezionare +Agg.. Attendere che lo schermo si aggiorni. Questo puo' prendere qualche minuto.

3. Selezionare la propria periferica (ad es. MF_XXXXXXXXXXXX) nell'elenco e selezionare Seguente.

4. A seconda del sistema operativo del proprio PC e del modello del proprio terminale, scegliere il driver della stampante da installare e premere Seguente, quindi verificare le impostazioni tecniche e cliccare Seguente e Fine.

5. Inserire un nome per la registrazione del proprio PC, cliccare su OKe seguire le istruzioni.

6. Selezionare la stampante desiderata sul Companion monitor

Per ulteriori dettagli: Cliccare sull'icona "Companion Director" sul proprio desktop per aprire Companion Director. Cliccare sul pulsante "Aiuto" per visualizzare la guida utente completa. Si veda il capitolo "Funzionalit PC / Companion Monitor / Gestione periferica / Aggiungere una periferica collegata alla rete ".

Importante: Quando si utilizza il WLAN, solo le funzioni di stampa e di scan sono disponibili. L'adattatore WLAN e DECT non sono compatibili simultaneamente, non utilizzarli assieme.

Stellen Sie sicher, dass die CD-ROM Xerox Phaser 3100MFP Documentation and Companion Pro Software auf dem Computer installiert ist.

Installieren Sie die CD-ROM Xerox Phaser 3100MFP WLAN erst, wenn Sie dazu aufgefordert werden.

1.Stecken Sie den USB-WLAN-Stick in das Multifunktionsgert ein

2.Konfiguration des USB-WLAN-Sticks Fr die Konfiguration des USB-WLAN-Sticks sind zwei verschiedene Modi verfgbar, Wenn Sie einen bereits in Ihrem Netzwerk vorhandenen WLAN-Router verwenden mchten, whlen Sie den Infrastrukturmodus. Whlen Sie ansonsten den Ad-Hoc-Modus.

Infrastrukturmodus 1. Drcken Sie auf dem Phaser 3100MFP , whlen Sie mit Hilfe der Tasten

bzw. das Men EINSTELLUNGEN, und besttigen Sie die Auswahl mit OK.

2. Whlen Sie mit Hilfe der Tasten bzw. die Option WLAN, und besttigen Sie die Auswahl mit OK.

3. Whlen Sie mit Hilfe der Tasten bzw. das Men CONFIG ASS., und besttigen Sie die Auswahl mit OK.

4. Whlen Sie mit Hilfe der Tasten bzw. Ihr WLAN aus der Liste aus, und besttigen Sie die Auswahl mit OK.

Hinweis: Wenn Ihr Netzwerkname in der Liste nicht aufgefhrt ist, whlen Sie unten in der Liste die Option NEUES NETZWERK (Neues Netzwerk). Geben Sie dann ber den Ziffernblock die SSID (bis zu 32 Zeichen langer Netzwerkname) an, und whlen Sie als Modus INFRA (Infastrukturmodus).

5. Wenn Ihr WLAN verschlsselt ist (WEP oder WAP), mssen Sie ber die Steuerung den Schlssel fr das Netzwerk eingeben. Weitergehende Informationen finden Sie im Benutzerhandbuch Ihres Gateways oder Computers.

6. Auf dem Display werden die beiden Optionen IP CONF.: MANU und IP CONF.: AUTO angezeigt. Es wird empfohlen, die IP-Adresse automatisch festzulegen. Whlen Sie dazu mit Hilfe der Tasten bzw. die Option IP CONF.:AUTO, und besttigen Sie die Auswahl mit OK. Wenn Sie die manuelle Konfiguration whlen, geben Sie die Werte fr die Parameter IP ADDRESS, SUBNET MASK und GATEWAY ein.

7. Drcken Sie dann auf OK, um das Gert mit den genderten WLAN- Einstellungen neu zu starten. Wenn das Netzwerk erfolgreich konfiguriert ist, sollte die LED-Anzeige des USB-WLAN-Sticks aufleuchten.

Ad-hoc-Modus 1. Drcken Sie auf dem Phaser 3100-Multifunktionsgert , whlen Sie mit

Hilfe der Tasten bzw. das Men EINSTELLUNGEN, und besttigen Sie die Auswahl mit OK.

2. Whlen Sie mit Hilfe der Tasten bzw. die Option WLAN, und besttigen Sie die Auswahl mit OK.

3. Whlen Sie mit Hilfe der Tasten bzw. das Men CONFIG ASS., und besttigen Sie die Auswahl mit OK.

4. Whlen Sie mit Hilfe der Tasten bzw. die Option NEW NETWORK (Neues Netzwerk), und besttigen Sie die Auswahl mit OK.

5. Auf dem Display wird die Eingabeaufforderung SSID angezeigt. Geben Sie mit Hilfe des Ziffernblocks den Namen des neuen Netzwerks ein, indem Sie bis zur Erlangung des gewnschten Namens auf die Tasten drcken (max. 32 Zeichen) und besttigen Sie mit OK.

6. Auf dem Display werden die Optionen AD-HOC MODE und MODE INFRA. angezeigt. Whlen Sie die Option AD-HOC MODE, und besttigen Sie die Einstellung mit OK.

7. Das Untermen KANAL wird angezeigt. Geben Sie eine Zahl zwischen 1 und 11 ein, und besttigen Sie die Eingabe mit OK.

8. Whlen Sie aus den Optionen OHNE und WEP die gewnschte Option fr die Verschlsselung aus, und besttigen Sie die Auswahl mit OK. Wenn Sie WEP whlen, geben Sie den WEP-Schlssel ein, den Sie in Ihrem Netzwerk verwenden.

9. Auf dem Display werden die beiden Optionen IP CONF.: MANU und IP CONF.: AUTO angezeigt. Es wird empfohlen, die IP-Adresse automatisch festzulegen. Whlen Sie dazu mit Hilfe der Tasten bzw. die Option IP CONF.:AUTO, und besttigen Sie die Auswahl mit OK. Wenn Sie die manuelle Konfiguration whlen, geben Sie die Werte fr die Parameter IP ADDRESS, SUBNET MASK und GATEWAY ein.

10.Nun sollte wieder das Hauptmen CONFIG ASS. angezeigt werden. Drcken Sie dann auf OK, um das Gert mit den genderten WLAN- Einstellungen neu zu starten. Wenn das Netzwerk erfolgreich konfiguriert ist, sollte die LED-Anzeige des USB-WLAN-Sticks aufleuchten.

11.ffnen Sie das Dialogfeld zur Konfiguration des WLANs auf dem Computer, whlen Sie die oben eingerichtete SSID aus, und stellen Sie eine Verbindung zu diesem Netzwerk her, indem Sie auf Verbinden klicken. Warten Sie, bis die Verbindung hergestellt ist. Dies kann ggf. einige Minuten dauern.

12.Wenn die fetgelegte SSID nicht angezeigt wird, berprfen Sie die Schritte fr die Einrtichtung des Ad-hoc-Modus 1-12.

3.Abschluss der Konfiguration des USB-WLAN- Sticks 1. Legen Sie die CD-ROM Phaser 3100MFP Wireless Adapter in das

Laufwerk des Computers ein. 2. Whlen Sie dann auf den angezeigten Dialogfeldern nacheinander die

Optionen Yes (Ja), Next (Weiter), I accept (Annehmen) und Next, und folgen Sie den auf dem Bildschirm angezeigten Anweisungen. Je nach Konfiguration Ihres Computers werden Sie mglicherweise dazu aufgefordert, einen neustart durchzufhren. berprfen Sie anschlieend, ob Companion Monitor geladen wurde (in diesem Fall werden auf dem Desktop zwei Xerox-Symbole angezeigt). Wiederholen Sie andernfalls die Installation.

3. Schlieen Sie das USB-Kabel an Die Treiber daraufhin werden automatisch installiert. Warten Sie, bis die Installation der Treiber abgeschlossen ist.

4. Fhren Sie das Firmwareupgrade fr das Multifunktionsgert durch, indem Sie den Anweisungen am Bildschirm folgen, und starten Sie das Gert neu. Entfernen Sie dann das USB-Kabel.

4.Hinzufgen des Druckers zu der Liste der WLANs des Computers 1. Wenn Sie das Gert fr den Ad-hoc-Modus konfiguriert haben, mssen Sie

mglicherweise (je nach Konfiguration des Computers) das Dialogfeld zur Konfiguration des WLANs auf dem Computer ffnen, die oben eingerichtete SSID auswhlen, und eine Verbindung zu diesem Netzwerk herstellen, indem Sie auf Verbinden klicken. Warten Sie, bis die Verbindung hergestellt ist. Dies kann ggf. einige Minuten dauern. Wenn Sie das Gert fr den Infrastrukturmodus konfiguriert haben, fahren Sie mit Schritt 2 fort.

2. Doppelklicken Sie auf das Symbol Xerox Companion Monitor, und whlen Sie dann in der Registerkarte Device selection (Gerteauswahl) die Option +Add (Hinzufgen). Warten Sie, bis die Anzeige aktualisiert wird. Dies kann ggf. einige Minuten dauern.

3. Whlen Sie in der Liste das Gert (der Name entspricht MF_XXXXXXXXXXXX), und klicken Sie auf Next.

4. Whlen Sie abhngig von dem Betriebssystem Ihres Computers und der Baureihe des Gerts den gewnschten Druckertreiber zur Installation aus, und klicken Sie auf Next. berprfen Sie in dem anschlieend angezeigten Dialogfeld die Einstellungen, und klicken Sie erneut auf Next und dann auf Finish (Fertigstellen).

5. Geben Sie einen Namen fr den Computer ein, klicken Sie auf OK, und folgen Sie den Anweisungen am Bildschirm.

6. Whlen Sie den gewnschten Drucker fr Companion Monitor aus.

Weitergehende Informationen erhalten Sie, indem Sie auf das Symbol Companion Director auf Ihrem Desktop klicken, um Companion Director zu ffnen. Klicken Sie auf die Schaltflche Help (Hilfe), um die Betriebsanleitung zu ffnen. Wichtige Informationen finden Sie unter Computer-Funktionen/ Companion Monitor/Gerteverwaltung/Hinzufgen eines Netzwerkgerts. Achtung: Bei einer Netzwerkanbindung ber das WLAN sind ausschlielich die Funktionen zum Drucken und Scannen verfgbar. Der WLAN-USB-Stick ist nicht mit DECT kompatibel, verwenden Sie daher nicht beide Technologien gleichzeitig.

Xerox Phaser 3100MFP Documentation and Companion Pro Software"

CDsinin bilgisayarnzda kurulu olduundan emin olun Sizden kurmanz isteninceye kadar "Xerox Phaser 3100MFP WLAN" CDsini

kurmayn.

1. Kablosuz Adaptr MFPye yerletirin

2. Kablosuz Adaptr Yaplandrmas Kablosuz Adaptr yaplandrmas iin iki yntem mevcuttur: Kablosuz routernz varsa ve router kullanmak istiyorsanz, Altyap metodunu aksi halde Ad-Hoc metodunu sein.

Altyap Ynetemi 1. Phaser 3100MFP zerindeki e basn, ya da tular yardmyla

KURULUM sein ve OK ile onaylayn. 2. ya da tular yardmyla WLAN sein ardndan OK ile onaylayn.

3. ya da tular yardmyla CONFIG. ASS. sein ve OK ile onaylayn.

4. ya da tular yardmyla listeden kablosuz varolan an adn sein ardndan OK ile onaylayn.

Not: Anz listede grnmyorsa, listenin sonunda YEN A seeneini seip ardndan SSID (saysal tu takmn kullanarak a adn maksimum 32 karakter olarak) girin ve INFRA modunu sein.

5. Eer kablosuz anz bir kriptolama anahtarna sahipse (WEP ya da WPA), anzn kulland anahtar kontrol panosundan girmeniz arttr. Daha fazla bilgi iin a geidi ya da bilgisayar klavuzuna baknz.

6. IP AYAR : EL LE ya da IP AYAR.: OTOM. ekranda belirir. ya da tular yardmyla IP AYAR:OTOM seeneini seerek Otomatik IP adresini kullanmanz neririz ardndan OK ile onaylayn.

Sistemi elle kurmay seerseniz, IP ADRES, ALT A MASKES ve A GEDparametrelerini girin.

7. OKe bastnzda, yeni WLAN parametrelerinin geerli olmalar iin aygt yeniden balatlr. A kurulumu yapldnda Kablosuz Adaptr LEDi yanmaldr.

Ad-Hoc Ynetemi 1. Phaser 3100MFP zerindeki e basn, ya da tular yardmyla

KURULUM sein ve OK ile onaylayn.

2. ya da tular yardmyla WLAN sein ardndan OK ile onaylayn.

3. ya da tular yardmyla CONFIG. ASS. sein ve OK ile onaylayn.

4. ya da tular yardmyla YEN A sein ve OK ile onaylayn. 5. Ekranda SSID grnr, saysal tu takmn kullanarak ve istediiniz ad elde

edinceye kadar tulara arka arkaya basarak a adn girin (maksimum 32 karakter) ve OK ile onaylayn.

6. AD-HOC MODU ya da MOD INFRA ekranda grnr. AD-HOC MODunu sein ve OK ile onaylayn.

7. KANAL alt mens belirir, 1 ile 11 arasnda bir say girin ve OK ile onaylayn. 8. Kriptolama ynetiminizi sein, W/O Gvenlik ya da WEP Kriptolama, ardndan

OK ile onaylayn. Eer WEPi seerseniz, anzda kullanmak istediiniz WEP anahatarn girin.

9. IP AYAR : EL LE ya da IP AYAR.: OTOM. ekranda belirir. ya da tular yardmyla IP AYAR:OTOM seeneini seerek Otomatik IP adresini kullanmanz neririz ardndan OK ile onaylayn. Eer sistemi el ile kurmay seerseniz, IP ADRES, ALT A MASKES ve A GED ayarlarn girin.

10. Artk CONFIG. ASS.'n ana blmne dnmenizi neririz. OKye bastnz anda yeni WLAN ayarlarn iermek iin aygt yeniden balar. An kurulduu anda, kablosuz adaptatrn LED yanar.

11. PC kablosuz balantlarnz an ve SSID adnz (daha nce belirlenmi olan) ve balan sein. Baland yazs ekrana gelinceye kadar bekleyin. Bu ilem birka dakika srebilir.

12. SSID adnz grnmezse Ad-Hoc 1-12. admlarn dorulayn.

3. Kablosuz Adaptr Yaplandrdktan Sonra 1. Phaser 3100MFP Wireless Adapter CDsini bilgisayarnza takn. 2. Evet, leri, Kabul ediyorum, leri seeneklerini sein ve talimatlar izleyin. PC

yaplandrmasna bal olarak bilgisayar yeniden balatlabilir. Yeniden balatldktan sonra Companion Monitorun yklendiini dorulayn (masastnde iki adet Xerox simgesi grnmelidir), aksi halde yeniden deneyin.

3. USB kabloyu balayn. Src kurulumu otomatik olarak balayacaktr. Kurulumun sonunu bekleyin.

4. MFP rn bilgisini gncellemek iin talimatlar izleyin ve MFPnin yeniden balatlmasn bekleyin, ardndan USB kabloyu karn.

4. PC Kablosuz A listesine yazc ekleme 1. Ad-hoc yntemini kullanrsanz. PC yaplandrmasna bal olarak PC kablosuz

balantlarn amanz ve SSID adnz (daha nce belirlenmi olan) ve Balan semeniz gerekebilir. Baland yazs ekrana gelinceye kadar bekleyin. Bu ilem birka dakika srebilir. Altyap yntemini kullanrsanz 2. adma gidin.

2. Aygt seimi sekmesinde Xerox Companion Monitor simgesine ift tklayn ve +Ekleyi sein. Ekrann yenilenmesini bekleyin. Bu ilem birka dakika srebilir.

3. Listeden aygtnz sein (rn. MF_XXXXXXXXXXXX) ve ardndan leriye tklayn.

4. Bilgisayarnzdaki letim Sistemine ve makinenizin modeline bal olarak yklenecek yazc srcsn sein ve leriye tklayn. Ardndan teknik ayarlar kontrol edin, leri ve Sona tklayn.

5. Bilgisayarnz iin bir kayt ad girin, OKe tklayn ve talimatlar izleyin. 6. Companion monitrde kullanmak istediiniz yazcy sein.

Daha fazla bilgi iin: Masastnde bulunan "Companion Director" simgesine tklayarak Companion Director an. Ayrntl kullanc klavuzunu grntlemek iin "Yardm" dmesine tklayn. Bkz. blm "PC zellikleri / Companion Monitor / Aygt Ynetimi / Aa bal bir aygt ekleme.

nemli: WLAN kullandnzda sadece yazdrma ve tarama fonksiyonlar kullanlabilir. WLAN adaptr ve DECT uyumlu deildir, birlikte kullanmayn.Nome del driver della stampante e

dello scanner Collegamento

Xerox Phaser 3100 MFP USB

Phaser 3100MFP WLAN WLAN Name des Drucker-

Manualsnet FAQs

If you want to find out how the Wireless adapter Xerox works, you can view and download the Xerox Wireless adapter Adapter Installation Instructions on the Manualsnet website.

Yes, we have the Installation Instructions for Xerox Wireless adapter as well as other Xerox manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Installation Instructions should include all the details that are needed to use a Xerox Wireless adapter. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Xerox Wireless adapter Adapter Installation Instructions is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Xerox Wireless adapter Adapter Installation Instructions consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Xerox Wireless adapter Adapter Installation Instructions free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Xerox Wireless adapter Adapter Installation Instructions, simply download the document to your computer. Once downloaded, open the PDF file and print the Xerox Wireless adapter Adapter Installation Instructions as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.