- Manuals
- Brands
- Vivotek
- Switch
- AW-IHT-1271
- CLI User Guide
Vivotek AW-IHT-1271 Switch CLI User Guide PDF
Summary of Content for Vivotek AW-IHT-1271 Switch CLI User Guide PDF
M ANAGEMENT G UIDE
AW-IHT-1271
CLI User Guide
Industrial VivoCam L2+ Managed PoE Switch
8xGE PoE + 4xGE SFP
Release A1
ABOUT THIS GUIDE
PURPOSE This guide gives specific information on how to operate CLI
to manage this switch.
AUDIENCE The guide is intended for use by network administrators who are responsible for operating and maintaining network equipment; consequently, it assumes a basic working knowledge of general switch functions, the RS-232 Console , Internet Protocol (IP), and Telnet Protocol.
Revision History
Release Date Revision Initial Release 2018/03/30 A1
CONTENTS
ABOUT THIS GUIDE ..................................................................................................................................................... II
REVISION HISTORY ........................................................................................................................................ III
CONTENTS ............................................................................................................................................................ 1
1 CLI MANAGEMENT ......................................................................................................................................... 3
1-1 LOGIN ......................................................................................................................................................................... 4
1-2 COMMANDS OF CLI ....................................................................................................................................................... 5
1-3 GLOBAL COMMANDS OF CLI ........................................................................................................................................... 6
2 CLEAR OF CLI .............................................................................................................................................. 9
3 CONFIGURE COMMANDS OF CLI ...................................................................................................................10
4 COPY COMMANDS OF CLI ................................................................................................................................ 147
5 DELETE COMMANDS OF CLI ............................................................................................................................. 148
6 DIR COMMANDS OF CLI ................................................................................................................................... 149
7 DISABLE COMMANDS OF CLI ............................................................................................................................ 150
8 DO COMMANDS OF CLI .................................................................................................................................... 151
9 DOT1X OF CLI ................................................................................................................................................... 152
10 ENABLE OF CLI ................................................................................................................................................ 153
11 ERPS OF CLI .................................................................................................................................................... 154
12 FIRMWARE OF CLI .......................................................................................................................................... 155
13 IP OF CLI ......................................................................................................................................................... 156
14 IPV6 OF CLI ..................................................................................................................................................... 157
15 LINK-OAM OF CL I ........................................................................................................................................... 158
16 NO OF CLI ....................................................................................................................................................... 158
17 PING OF CLI .................................................................................................................................................... 160
18 PLATFORM OF CLI ........................................................................................................................................... 162
19 PTP OF CLI ...................................................................................................................................................... 163
20 RELOAD OF CLI ............................................................................................................................................... 165
21 SEND OF CLI ................................................................................................................................................... 166
22 SHOW OF CLI .................................................................................................................................................. 167
23 TERMINAL OF CLI ........................................................................................................................................... 238
24 TRACEROUTE OF CLI ..................................................................................................................................... 240
25 VERIPHY OF CLI ............................................................................................................................................ 289
1 CLI Management
The following description is the brief of the network connection.
-- Locate the correct DB-9 (RS-232) cable with female DB-9 connector. RS-232 cable is used for connecting a terminal or
termial emulator to the Managed Switchs RJ45 port to access the command-line interface.
-- Attach the RJ45 serial port on the switchs front panel which used to connect to the switch for console configuration
-- Attach the other end of the DB-9 cable to an ASCII terminal emulator or PC Com-1, 2 port. For example, PC runs
Microsoft Windows HyperTerminal utility.
-- At Com Port Properties Menu, configure the parameters as below: (see the next section)
Baud rate 115200
Stop bits 1
Data bits 8
Parity N
Flow control none
1-1 Login
The command-line interface (CLI) is a text-based interface. User can access the CLI through either a direct serial
connection to the device or a Telnet session (Default IP address: DHCP Client). The default uaser and password to login
into the Managed Switch are listed below:
Username: admin
Password:
Note:
After you login successfully, the prompt will be shown as
behave as an administrator and have the privilege for setting the Managed Switch. If log as not the administrator, the
prompt will be shown as
under the administrator. Each CLI command has its privilege
Username: admin
Password: admin
AW-IHT-1271#
1-2 Commands of CLI
The CLI is divided into serveral modes. If a user has enouth privilege to run a particular command, the user has to
run the command in the correct mode. To see the commands of the mode, please input ? after the system prompt, then
all commands will be listed in the screen. The command modes are listed as belows:
Command Modes
MODE PROMPT COMMAND FUNCTION IN THIS MODE
exec
maintenance
config
Config-if
Config-if-vlan
Config-line
Config-impc-profile
Config-snmp-host
Config-stp-aggr
Config-dhcp-pool
Config-rfc2544-profile
Commandsreside in the corresponding modes could runonly in that mode. If a user wants to run a particular command,
the user has to change to the appropriate mode. The command modes are organized as a tree, and users start to in
enable mode. The following table explains how to change from one mode to another.
Change Between Command Modes
MODE ENTER MODE LEAVE MODE
exec -- --
config Configure terminal exit
config-interfcae Interface
config-vlan Interface vlan
1-3 Global Commands of CLI
AW-IHT-1271# ?
clear Reset functions
configure Enter configuration mode
copy Copy from source to destination
delete Delete one file in flash: file system
dir Directory of all files in flash: file system
disable Turn off privileged commands
do To run exec commands in config mode
dot1x IEEE Standard for port-based Network Access Control
enable Turn on privileged commands
erps Ethernet Ring Protection Switching
exit Exit from EXEC mode
firmware Firmware upgrade/swap
help Description of the interactive help system
ip IPv4 commands
ipv6 IPv6 configuration commands
link-oam Link OAM configuration
logout Exit from EXEC mode
more Display file
no Negate a command or set its defaults
ping Send ICMP echo messages
platform Platform configuration
ptp Misc non persistent 1588 settings
reload Reload system.
send Send a message to other tty lines
show Show running system information
Exit
Exit from EXEC mode.
Syntax:
exit
Parameter:
None.
Example:
Help
Description of the interactive help system.
Syntax:
help
Parameter:
None.
Example:
AW-IHT-1271# help
Help may be requested at any point in a command by entering
a question mark '?'. If nothing matches, the help list will
be empty and you must backup until entering a '?' shows the
available options.
Two styles of help are provided:
1. Full help is available when you are ready to enter a
command argument (e.g. 'show ?') and describes each possible
argument.
2. Partial help is provided when an abbreviated argument is
entered
and you want to know what arguments match the input
(e.g. 'show pr?'.)
AW-IHT-1271#
AW-IHT-1271(config)# exit
AW-IHT-1271#
terminal Set terminal line parameters
traceroute traceroute program
veriphy VeriPHY keyword
logout
Exit from EXEC mode.
Syntax:
logout
Parameter:
none
Example:
end
Go back to EXEC mode.
Syntax:
end
Example:
(config)# end
AW-IHT-1271#
AW-IHT-1271# logout
press ENTER to get started
2 CLEAR of CLI
Table : CLEAR Commands
Command Function
access Access management
access-list Access list
dot1x IEEE Standard for port-based Network Access Control
eps Ethernet Protection Switching.
erps Ethernet Ring Protection Switching
evc Ethernet Virtual Connections
ip Interface Internet Protocol config commands
ipv6 IPv6 configuration commands
lacp Clear LACP statistics
link-oam Clear Link OAM statistics
lldp Clears LLDP statistics.
logging Syslog
mac MAC Address Table
mep Maintenance Entity Point
mvr Multicast VLAN Registration configuration
ptp
sflow Statistics flow.
spanning-tree STP Bridge
statistics Clear statistics for a given interface
access
Access management.
Syntax:
clear access management statistics
Parameter:
management Access management configuration.
statistics Statistics data.
Example:
access-list
Access list.
Syntax:
Clear access-list ace statistics
Parameter:
ace Access list entry
statistics Traffic statistics
Example:
dot1x
IEEE Standard for port-based Network Access Control.
Syntax
Clear dot1x statistics
Clear dot1x statistics interface GigabitEthernet < PORT_TYPE_LIST>
Parameter
statistics Clears the statistics counters
interface Interface
GigabitEthernet 1 Gigabit Ethernet Port
PORT_TYPE_LIST Port list in 1/1-12 for Gigabitethernet
EXAMPLE
AW-IHT-1271# clear dot1x statistics interface GigabitEthernet 1/1-12
AW-IHT-1271#
AW-IHT-1271# clear access-list ace statistics
AW-IHT-1271#
AW-IHT-1271# clear access management statistics
AW-IHT-1271#
eps
Ethernet Protection Switching.
Syntax
clear eps
Parameter
The EPS instance number.
wtr Clear active WTR
EXAMPLE
erps
Ethernet Ring Protection Switching
Syntax
clear erps 1-64 command [ ( clear | force | manual ) ( port0 | port1 ) ]
Parameter
1-64 ERPS group number
command Administrative Command
clear Clear command
force Force command
manual Manual command
port0 ERPS Port 0 interface
port1 ERPS Port 1 interface
EXAMPLE
evc
Ethernet Virtual Connections
AW-IHT-1271# clear erps 1 command clear port0
AW-IHT-1271#
AW-IHT-1271# clear eps 1 wtr
AW-IHT-1271#
Syntax
clear evc statistics
clear evc statistics interface [ * | GigabitEthernet ]
Parameter
statistics Statistic counters
interface Interface
* All switches or All ports
GigabitEthernet 1 Gigabit Ethernet Port
Port list for all port types
Port list in 1/1-12
EXAMPLE
ip
Interface Internet Protocol config commands
Syntax
clear ip arp
clear ip dhcp detailed statistics { server | client | snooping | relay | helper | all } [ interface (
[
clear ip dhcp relay statistics
clear ip dhcp server binding
clear ip dhcp server binding { automatic | manual | expired }
clear ip dhcp server statistics
clear ip dhcp snooping statistics [ interface (
clear ip igmp snooping [ vlan
clear ip statistics [ system ] [ interface vlan
Parameter
arp Clear ARP cache
dhcp Dynamic Host Configuration Protocol
igmp Internet Group Management Protocol
statistics Traffic statistics
AW-IHT-1271# clear evc statistics
AW-IHT-1271#
relay DHCP relay agent configuration
snooping DHCP snooping
interface Select an interface to configure
GigabitEthernet 1 Gigabit Ethernet Port
vlan IPv4 traffic interface
VLAN identifier(s): VID
EXAMPLE
ipv6
IPv6 configuration commands.
Syntax
clear ipv6 mld snooping [ vlan
clear ipv6 neighbors
clear ipv6 statistics [ system ] [ interface vlan
Parameter
mld Multicasat Listener Discovery
neighbors Ipv6 neighbors
statistics Traffic statistics
snooping Snooping MLD
statistics Running MLD snooping counters
vlan Ipv6 interface traffic
VLAN identifier(s): VID
icmp IPv6 ICMP traffic
AW-IHT-1271# clear ip arp
AW-IHT-1271# clear ip dhcp detailed statistics all
interface GigabitEthernet 1/1-12
AW-IHT-1271# clear ip dhcp relay statistics
AW-IHT-1271# clear ip dhcp server binding 192.168.1.11
AW-IHT-1271# clear ip dhcp server binding automatic
AW-IHT-1271# clear ip dhcp server statistics
AW-IHT-1271# Clear ip dhcp snooping statistics interface
GigabitEthernet 1/1-12
AW-IHT-1271# clear ip igmp snooping vlan 1 statistics
AW-IHT-1271# clear ip statistics system interface
AW-IHT-1271# clear ip statistics system interface vlan 1
icmp icmp-msg 2
icmp-msg IPv6 ICMP traffic for designated message type
interface Select an interface to configure
system IPv6 system traffic
< 0~255> ICMP message type ranges from 0 to 255
EXAMPLE
lacp
Clear LACP statistics
Syntax
Clear lacp statistics
Parameter
statistics Clear all LACP statistics
EXAMPLE
lldp
Clears LLDP statistics.
Syntax
Clear lldp statistics
Clear lldp statistics| begin | exclude | include >< LINE >
Parameter
statistics Clears LLDP statistics.
| Output modifiers
begin Begin with the line that matches
exclude Exclude lines that match
include Include lines that match
String to match output lines
EXAMPLE
AW-IHT-1271# clear lacp statistics
AW-IHT-1271#
AW-IHT-1271# clear ipv6 mld snooping vlan 3 statistics
AW-IHT-1271# clear ipv6 neighbors
AW-IHT-1271# Clear ipv6 statistics system icmp icmp-msg 2
link-oam
Clear Link OAM statistics
Syntax
clear link-oam statistics
clear link-oam statistics interface ( * | GigabitEthernet )
Parameter
statistics Clear Rx/Tx counters
interface Clear Link OAM statistic on a specific interface or all interfaces.
* All switches or All ports
GigabitEthernet 1 Gigabit Ethernet Port
Port list for all port types
Port list in 1/1-12
EXAMPLE
logging
Syslog.
Syntax
clear logging [ info ] [ warning ] [ error ] [ switch
Parameter
error Error
info Information
warning Warning
EXAMPLE
mac
AW-IHT-1271# clear logging info error warning
AW-IHT-1271#
AW-IHT-1271# clear link-oam statistics interface
GigabitEthernet 1/12
AW-IHT-1271# clear lldp statistics | begin LINE
AW-IHT-1271#
MAC Address Table.
Syntax
Clear mac address-table
Parameter
address-table Flush MAC Address table.
EXAMPLE
mep
Maintenance Entity Point
Syntax
Clear mep
Parameter
The MEP instance.
bfd Clear G.8113.2 BFD CC/CV statistics counters.
dm Clear DM measuring information.
lm Clear LM measuring information.
tst Clear TST measuring information.
EXAMPLE
mvr
Multicast VLAN Registration configuration.
Syntax
clear mvr [ vlan
Parameter
name MVR multicast name
statistics Running MVR protocol counters
vlan MVR multicast vlan
< word16> MVR multicast VLAN name
MVR multicast VLAN list
AW-IHT-1271# clear mep 1 dm
AW-IHT-1271#
AW-IHT-1271# clear mac address-table
AW-IHT-1271#
EXAMPLE
ptp
Syntax
clear ptp <0-3> servo
Parameter
<0-3>
Servo
EXAMPLE
sflow
Statistics flow.
Syntax
clear sflow statistics { receiver [
[
Parameter
interface Interface
receiver Clear statistics for receiver.
GigabitEthernet
runtime
Port list in 1/1-12 for Gigabitethernet
EXAMPLE
AW-IHT-1271# clear sflow statistics interface
GigabitEthernet 1/1-12
AW-IHT-1271# clear ptp 1 servo
AW-IHT-1271#
AW-IHT-1271# clear mvr vlan 25 statistics
AW-IHT-1271#
spanning-tree
STP Bridge.
Syntax
clear spanning-tree { { statistics [ interface (
[ interface (
Parameter
detected-protocols Set the STP migration check
statistics STP statistics
interface Choose port
GigabitEthernet
Port list in 1/1-12 for Gigabitethernet
EXAMPLE
statistics
Clear statistics for a given interface
Syntax
clear statistics interface
clear statistics <port_type>
Parameter
GigabitEthernet
Port list in 1/1-12 for Gigabitethernet
EXAMPLE
AW-IHT-1271# clear statistics GigabitEthernet 1/1-12
AW-IHT-1271#
AW-IHT-1271# clear spanning-tree detected-protocols interface GigabitEthernet
1/1-12
#
3 CONFIGURE Commands of CLI
Table : CONFIGURE Commands
Command Function
terminal Configure from the terminal
aaa Authentication, Authorization and Accounting
access Access management
access-list Access list
aggregation Aggregation mode
banner Define a login banner
clock Configure time-of-day clock
default Set a command to its defaults
dms Enable DMS Maste
do To run exec commands in config mode
dot1x IEEE Standard for port-based Network Access Control
enable Modify enable password parameters
end Go back to EXEC mode
eps Ethernet Protection Switching
erps Ethernet Ring Protection Switching
evc Ethernet Virtual Connections
exit Exit from Configuration mode
event Trap event severity level
green-ethernet Green ethernet (Power reduction)
gvrp Enable GVRP feature
help Description of the interactive help system
hostname Set system's network name
interface Select an interface to configure
ip Internet Protocol
ipmc IPv4/IPv6 multicast configuration
ipv6 IPv6 configuration commands
lacp LACP settings
line Configure a terminal line
lldp LLDP configurations.
logging Syslog
loop-protect Loop protection configuration
mac MAC table entries/configuration
mep Maintenance Entity Point
monitor Set monitor configuration.
mvr Multicast VLAN Registration configuration
no Negate a command or set its defaults
ntp Configure NTP
poe power over ethernet
port-security Enable/disable port security globally.
Privilege Command privilege parameters
ptp Precision time Protocol (1588)
qos Quality of Service
radius-server Configure RADIUS
rapid-ring Set Rapid Ring's configurations
ring-to-ring Set Ring to Ring's configurations
rmon Remote Monitoring
sflow Statistics flow.
smtp Set email information
snmp-server Set SNMP server's configurations
spanning-tree Spanning Tree protocol
switchalert-management SwitchAlert Management configuration
switchport Set switching mode characteristics
system Set the SNMP server's configurations
tacacs-server Configure TACACS+
tzidx Configure timezone city/area
udld Enable UDLD in the aggressive or normal mode and to set
the configurable message timer on all fiber-optic ports.
upnp Set UPnP's configurations
username Establish User Name Authentication
vlan VLAN commands
voice Voice appliance attributes
web Web
terminal
Configure from the terminal.
Syntax
configure terminal
EXAMPLE
AW-IHT-1271# configure terminal
AW-IHT-1271(config)#
aaa
Authentication, Authorization and Accounting.
SYNTAX
aaa authentication login { console | telnet | ssh | http } { { local | radius | tacacs } [ { local | radius | tacacs }
[ { local | radius | tacacs } ] ] }
Parameter
authentication Authentication
login Login
console Configure Console
http Configure HTTP
ssh Configure SSH
telnet Configure Telnet
local Use local database for authentication
radius Use RADIUS for authentication
tacacs Use TACACS+ for authentication
EXAMPLE
access
Access management.
SYNTAX
access management
access management
Parameter
AW-IHT-1271(config)# aaa authentication login http radius
AW-IHT-1271(config)#
management Access management configuration
< 1-16> ID of access management entry
< 1-4094> The VLAN ID for the access management entry
< ipv4_addr> Start IPv4 address
< ipv6_addr> Start IPv6 address
all All services
snmp SNMP service
telnet TELNET/SSH service
to End address of the range
web Web service
EXAMPLE
access-list
Table : configure access-list Commands
Command Function
ace Access list entry
rate-limiter Rate limiter
ace
Access list entry.
SYNTAX
access-list ace{ update<1-256> | <1-256> } [action< deny | filter | permit >]
access-list ace{ update<1-256> | <1-256> } [dmac-type < any | broadcast | multicast | unicast >]
access-list ace{ update<1-256> | <1-256> } [frametype < any | arp | etype | ipv4 | ipv4-icmp | ipv4-tcp | ipv4-udp
| ipv6 | ipv6-icmp | ipv6-tcp | ipv6-udp >]
AW-IHT-1271(config)# access management 10 3 192.168.1.1 all
AW-IHT-1271(config)#
access-list ace{ update<1-256> | <1-256> } [ ingress] [ ingress interface {
access-list ace{ update<1-256> | <1-256> } [ logging [ disable ] ]
access-list ace{ update<1-256> | <1-256> } [ lookup [ disable ] ]
access-list ace{ update<1-256> | <1-256> } [ mirror [ disable ] ]
access-list ace{ update<1-256> | <1-256> } [ next { <1-256> | last } ]
access-list ace{ update<1-256> | <1-256> } [ policy <0-255> [ policy-bitmask <0x0-0xFF> ] ]
access-list ace{ update<1-256> | <1-256> } [ rate-limiter { <1-16> | disable } ]
access-list ace{ update<1-256> | <1-256> } [redirect | interface {
access-list ace{ update<1-256> | <1-256> } [shutdown]
access-list ace{ update<1-256> | <1-256> } [ tag { tagged | untagged | any } ]
access-list ace{ update<1-256> | <1-256> } [ tag-priority { <0-7> | any } ]
access-list ace{ update<1-256> | <1-256> }[ vid { <1-4095> | any } ]
Parameter
action Access list action
dmac-type The type of destination MAC address
frametype Frame type
ingress Ingress
logging Logging frame information
lookup Second lookup
mirror Mirror frame to destination mirror port
next insert the current ACE before the next ACE ID
policy Policy
rate-limiter Rate limiter
redirect Redirect frame to specific port
shutdown Shutdown incoming port
tag Tag
tag-priority Tag priority
vid VID field
deny Deny
filter Filter
permit Permit
any Don't-care the type of destination MAC address
broadcast Broadcast destination MAC address
multicast Multicast destination MAC address
unicast Unicast destination MAC address
any Don't-care the frame type
arp Frame type of ARP
etype Frame type of etype
ipv4 Frame type of IPv4
ipv4-icmp Frame type of IPv4 ICMP
ipv4-tcp Frame type of IPv4 TCP
ipv4-udp Frame type of IPv4 TCP
ipv6 Frame type of IPv4
ipv6-icmp Frame type of IPv6 ICMP
ipv6-tcp Frame type of IPv6 TCP
ipv6-udp Frame type of IPv6 UDP
interface Select an interface to configure
Gigabitethernet
* All switches or All ports
Gigabitethernet 1 Gigabit Ethernet port
Port ID in the format of switch-no/port-no ex, 1/1-12 for Gigabitethernet
* or Gigabitethernet
* All Switches or All ports
Gigabitethernet 1 Gigabit Ethernet Port
Port list in 1/1-12
any Don't-care the ingress interface
<0-255> Policy ID
policy-bitmask The bitmask for policy ID
<0x0-0xFF> The value of policy bitmask
<1-4095> The value of VID field
<0-7> The value of tag priority
EXAMPLE
rate-limiter
Rate limiter.
SYNTAX
access-list rate-limiter [ <1~16> ] { pps <0-3276700> | 100kbps <0-10000> }
Parameter
100kbps 100k bits per second
Rate limiter ID
Rate value
<0-10000> Rate value
EXAMPLE
AW-IHT-1271(config)# access-list ace 10 action deny
AW-IHT-1271(config)#
aggregation
Aggregation mode.
SYNTAX
aggregation mode { [ dmac ] [ ip ] [ dmac ] [ port ] }
Parameter
mode Traffic distribution mode
dmac Destination MAC affects the distribution
ip IP address affects the distribution
port IP port affects the distribution
smac Source MAC affects the distribution
EXAMPLE
banner
Define a login banner
SYNTAX
banner [ motd ]
banner exec
banner login
Parameter
AW-IHT-1271(config)# aggregation mode ip port dmac smac
AW-IHT-1271(config)#
AW-IHT-1271(config)# access-list rate-limiter 100kbps
111
AW-IHT-1271(config)#
c banner-text c, where 'c' is a delimiting character
exec Set EXEC process creation banner
login Set login banner
motd Set Message of the Day banner
EXAMPLE
clock
Configure time-of-day clock.
SYNTAX
clock set
clock summer-time
clock summer-time
clock timezone
Parameter
set set clock
summer-time Configure summer (daylight savings) time
timezone Configure time zone
yyyy/mm/dd
hh:mm:ss
<2000-2097> Year to start
AW-IHT-1271(config)# banner exec LINE
Enter TEXT message. End with the character 'L'.
L
AW-IHT-1271(config)#
hh:mm Time to start (hh:mm)
<1-12> Month to end
<1-31> Date to end
<2000-2097> Year to end
hh:mm Time to end (hh:mm)
<1-1440> Offset to add in minutes
<1-5> Week number to start
<1-7> Weekday to start
<1-12> Month to start
EXAMPLE
default
Set a command to its defaults
SYNTAX
default access-list rate-limiter [
Parameter
access-list Access list
rate-limiter Rate limiter
Rate limiter ID
EXAMPLE
AW-IHT-1271(config)# default access-list rate-limiter 3
AW-IHT-1271(config)#
AW-IHT-1271(config)# clock set 2016/09/30 10:22:03
2016-09-30T10:22:03+00:00
AW-IHT-1271(config)# do show clock
System Time : 2016-09-30T10:22:48+00:00
dms
Enable DMS Maste
SYNTAX
dms mode [ disabled | enabled | high-priority ]
Parameter
mode DMS mode
disabled DMS mode is disabled
enabled DMS mode is enabled
high-priority DMS mode is high priority
EXAMPLE
do
To run exec commands in config mode.?
SYNTAX
do < LINE >{[< LINE >]}
Parameter
Exec Command
EXAMPLE
AW-IHT-1271(config)# dms mode high-priority
AW-IHT-1271(config)#
dot1x
IEEE Standard for port-based Network Access Control.
SYNTAX
dot1x authentication timer inactivity
dot1x authentication timer re-authenticate
dot1x feature { [ guest-vlan ] [ radius-qos ] [ radius-vlan ] }*1
dot1x guest-vlan
dot1x guest-vlan supplicant
dot1x max-reauth-req
dot1x re-authentication
dot1x system-auth-control
dot1x timeout quiet-period
dot1x timeout tx-period
Parameter
authentication Authentication
feature Globally enables/disables a dot1x feature functionality
guest-vlan Guest VLAN
AW-IHT-1271(config)# do show vlan
VLAN Name Ports
--------------------------------------------------------------------------------
--------------------
1 default GigabitEthernet 1/1, GigabitEthernet 1/2,
GigabitEthernet 1/3,
GigabitEthernet 1/4, GigabitEthernet 1/5
AW-IHT-1271(config)#
max-reauth-req Guest VLAN ID used when entering the Guest VLAN.
re-authentication Set Re-authentication state
system-auth-control Set the global NAS state
timeout timeout
timer timer
inactivity Time in seconds between check for activity on successfully authenticated MAC
addresses.
re-authenticate The period between re-authentication attempts in seconds
<10-1000000> seconds
<1-3600> seconds
guest-vlan Globally enables/disables state of guest-vlan
radius-qos Globally enables/disables state of RADIUS-assigned QoS.
radius-vlan Globally enables/disables state of RADIUS-assigned VLAN.
<1-4095> The number of times a Request Identity EAPOL frame is sent
without response before considering entering the Guest VLAN.
supplicant The switch remembers if an EAPOL frame has been received on
the port for the life-time of the port. Once the switch
considers whether to enter the Guest VLAN, it will first
check if this option is enabled or disabled. If disabled
(unchecked; default), the switch will only enter the Guest
VLAN if an EAPOL frame has not been received on the port for
the life-time of the port. If enabled (checked), the switch
will consider entering the Guest VLAN even if an EAPOL frame
has been received on the port for the life-time of the port.
<1-255> number of times
quiet-period Time in seconds before a MAC-address that failed
authentication gets a new authentication chance.
tx-period the time between EAPOL retransmissions.
<10-1000000> seconds
<1-65535> seconds
EXAMPLE
enable
Modify enable password parameters.
SYNTAX
enable password [
enable secret { 0 | 5 } [< level> <1-15> ]
Parameter
password Assign the privileged level clear password
secret Assign the privileged level secret
WORD The UNENCRYPTED (cleartext) password
level Set exec level password
<1-15> Level number
0 Specifies an UNENCRYPTED password will follow
5 Specifies an ENCRYPTED secret will follow
EXAMPLE
AW-IHT-1271(config)# dot1x authentication timer inactivity 1000
AW-IHT-1271(config)# dot1x feature guest-vlan radius-qos radius-vlan
AW-IHT-1271(config)# dot1x guest-vlan 33
AW-IHT-1271(config)# dot1x max-reauth-req 3
AW-IHT-1271(config)# dot1x re-authentication
AW-IHT-1271(config)# dot1x system-auth-control
AW-IHT-1271(config)# dot1x timeout quiet-period 3000
eps
Ethernet Protection Switching.
SYNTAX
eps 1 1plus1 [ bidirectional | unidirectional ]
eps 1 1plus1 unidirectional aps
eps 1 command [ exercise | forced | freeze | lockout | lockoutlocal | manualp | manual ]
eps 1 domain port architecture [ 1for1 | 1plus1 ] work-flow [ GigabitEthernet |
[ GigabitEthernet |
eps 1 holdoff
eps 1 mep-work
eps 1 revertive [ 10m | 10s | 11m | 12m | 30s | 5m | 6m | 7m | 8m | 9m ]
eps 1 revertive wtr-value
Parameter
<1-100> The EPS instance number
1plus1 EPS 1+1 architecture.
command EPS command.
domain The domain of the EPS.
holdoff Hold off timer.
mep-work Working MEP instance.
revertive Revertive EPS.
bidirectional EPS 1+1 bidirectional protection type.
unidirectional EPS 1+1 unidirectional protection type.
AW-IHT-1271(config)# enable password level 10 999
AW-IHT-1271(config)#
aps EPS 1+1 unidirectional with APS protection type.
exercise Exercise of the protocol - not traffic effecting. This is only allowed in case of
'Bidirectional' protection type
forced Force switch normal traffic to protection.
freeze Local Freeze of EPS.
lockout Lockout of protection.
lockoutlocal Local lockout of EPS.
manualp Manual switch normal traffic to protection.
manualw Manual switch normal traffic to working. This is only allowed in case of 'non-
revertive' mode.
port This EPS is protecting in the Port domain.
pw This EPS is protecting in the MPLS-TP Pseudo-Wire domain.
tunnel-tp This EPS is protecting in the MPLS-TP tunnel domain.
architecture The EPS architecture.
1for1 The architecture is 1 for 1.
1plus1 The architecture is 1 plus 1.
work-flow The working flow instance that the EPS is related to.
GigabitEthernet 1 Gigabit Ethernet Port
The working flow instance number when not in the port domain.
Port ID in 1/1-12
protect-flow The protecting flow instance that the EPS is related to.
The hold off timer value in 100 ms. Max 10 sec.
Working MEP instance number.
mep-protect Protecting MEP instance.
Protecting MEP instance number.
mep-aps APS MEP instance.
APS MEP instance number.
10m WTR is 10 min.
10s WTR is 10 sec.
11m WTR is 11 min.
12m WTR is 12 min.
30s WTR is 30 sec.
5m WTR is 5 min.
6m WTR is 6 min.
7m WTR is 7 min.
8m WTR is 8 min.
9m WTR is 9 min.
wtr-value WTR as value.
The WTR value in seconds. Range is 1 to 720 seconds.
EXAMPLE
erps
Ethernet Ring Protection Switching
SYNTAX
erps 1-64 guard 10-2000
erps 1-64 holdoff 0-10000
erps 1-64 major port0 interface GigabitEthernet
AW-IHT-1271(config)# eps 1 1plus1 bidirectional
AW-IHT-1271(config)#
AW-IHT-1271(config)# eps 1 command manualw
AW-IHT-1271(config)#
AW-IHT-1271(config)# eps 1 revertive 10m
AW-IHT-1271(config)#
erps 1-64 major port0 interface GigabitEthernet
interconnect
erps 1-64 mep port0 sf 1-100 aps 1-100 port1 sf 1-100 aps 1-100
erps 1-64 revertive 1-12
erps 1-64 rpl [ neighbor | owner ] [ port0 | port1 ]
erps 1-64 sub port0 interface GigabitEthernet
erps 1-64 sub port0 interface GigabitEthernet
[ virtual-channel ]
erps 1-64 topology-change propagate
erps 1-64 version [ 1 | 2 ]
erps 1-64 vlan
erps 1-64 vlan [ add | remove ]
erps 1-64 vlan none
Parameter
1-64 ERPS group number
guard Guard
holdoff Hold-off time
major Major ring
mep MEP
revertive Revertive
rpl Ring Protection Link
sub Sub-ring
topology-change Topology Change
version Version
vlan VLAN
10-2000 Guard time in ms
0-10000 Hold-off time in ms
port0 ERPS Port 0 interface
interface Ethernet interface
GigabitEthernet 1 Gigabit Ethernet Port
Port ID in 1/1-12
port1 ERPS Port 1 interface
interconnect Major ring is interconnected
sf Signal Fail
1-100 Index of Port 0 SignalFail MEP
aps Automatic Protection Switching
1-12 Wait-to-restore time in minutes
neighbor Neighbor role
owner Owner role
interconnect Sub-ring is interconnected
1-64 Major ring group number
virtual-channel Enable virtual channel for sub-ring
propagate Propagate
1 ERPS version 1
2 ERPS version 2
List of VLANs
add Add to set of included VLANs
none Do not include any VLANs
remove Remove from set of included VLANs
EXAMPLE
evc
Ethernet Virtual Connections
SYNTAX
evc <1-256>
evc <1-256> inner-tag add { [ dei <0-1> ] | [ pcp <0-7> ] | [ preserve ] | [ type ( c-tag | none | s-custom-tag | s-tag ) ]
| [ vid
evc <1-256> interface ( * | GigabitEthernet ) [
evc <1-256> ivid
evc <1-256> learning [ disable | inner-tag | outer-tag ]
evc <1-256> outer-tag add vid
evc <1-256> vid <1-4095> [ inner-tag | interface | ivid | learning | outer-tag ]
Parameter
<1-256> EVC identifier
ece EVC Control Entry
policer Policer (ingress bandwidth profile)
AW-IHT-1271(config)# erps 1 guard 10
AW-IHT-1271(config)#
AW-IHT-1271(config)# erps 1 holdoff 0
AW-IHT-1271(config)#
AW-IHT-1271(config)# erps 1 major port0 interface GigabitEthernet 1/1 port1
interface GigabitEthernet 1/2 interconnect
AW-IHT-1271(config)#
AW-IHT-1271(config)# erps 1 mep port0 sf 1 aps 1 port1 sf 1 aps 1
AW-IHT-1271(config)#
AW-IHT-1271(config)# erps 1 revertive 1
AW-IHT-1271(config)#
AW-IHT-1271(config)# erps 1 rpl owner port1
AW-IHT-1271(config)#
update Update existing entry
inner-tag Setup inner tag options
interface Setup NNI port list
ivid Setup internal EVC VLAN ID
learning Setup learning
outer-tag Setup outer tag options
vid Setup EVC VLAN ID
add Setup inner tag add properties
dei Setup added tag DEI
pcp Setup added tag PCP
preserve Setup tag PCP/DEI preservation
type Setup added tag type
vid Setup added tag VLAN ID
vid-mode Setup inner tag VLAN ID mode
<0-1> Added tag DEI
disable Disable learning
Added tag VLAN ID
<0-7> Added tag PCP
c-tag Add C-tag
none No tag added
s-custom-tag Add custom S-tag
s-tag Add S-tag
normal Use EVC VLAN ID in outer tag
tunnel Use EVC VLAN ID in inner tag
* All switches or All ports
GigabitEthernet 1 Gigabit Ethernet Port
Port list for all port types
<1-4095> EVC VLAN ID
EXAMPLE
event
Trap event severity level.
SYNTAX
event group
disable } | ipush { enable | disable } }
Parameter
Group Configure trap event severity level
ACL, ACL_Log, Access_Mgmt, Auth_Failed, Cold_Start, Config_Info, FAN_FAIL,
Firmware_Upgrade, Import_Export, LACP, Link_Status, Login, Logout, Loop_Protect,
Mgmt_IP_Change, Module_Change, NAS, Password_Change, Poe_Auto_Check,
Port_Security, Temperature, VLAN, Voltage, Warm_Start
EXAMPLE
green-ethernet
Green ethernet (Power reduction)
SYNTAX
green-ethernet eee optimize-for-power
AW-IHT-1271(config)# event group VLAN trap enable
AW-IHT-1271(config)#
AW-IHT-1271(config)# evc 1 outer-tag add vid 3
AW-IHT-1271(config)#
Parameter
eee Powering down of PHYs when there is no traffic.
optimize-for-power Set if EEE shall be optimized for least power consumption (else optimized
for least traffic latency).
EXAMPLE
gvrp
Enable GVRP feature
SYNTAX
gvrp
gvrp max-vlans <1-4095>
gvrp time { [ join-time <1-20> ] [ leave-time <60-300> ] [ leave-all-time <1000-5000> ] }*1
Parameter
time config gvrp timer value in units of centi seconds [cs]
EXAMPLE
hostname
Set system's network name.
SYNTAX
hostname < WORD >
AW-IHT-1271(config)# gvrp max-vlans 333
AW-IHT-1271(config)# gvrp time join-time 13 leave-all-time 3000 leave-time 200
AW-IHT-1271(config)#
AW-IHT-1271(config)# green-ethernet eee optimize-for-power
AW-IHT-1271(config)#
Parameter
WORD This system's network name.
EXAMPLE
interface
Select an interface to configure.
SYNTAX
interface (
interface vlan
Parameter
GigabitEthernet
vlan VLAN interface configurations
List of VLAN interface numbers, 1-4095
Port list in 1/1-12 for Gigabitethernet
EXAMPLE
ip
Internet Protocol.
AW-IHT-1271(config)# interface GigabitEthernet 1/1-8
AW-IHT-1271(config-if)# poe weekday Fri hour 22
AW-IHT-1271(config-if)# AW-IHT-1271(config)# interface vlan 3
AW-IHT-1271(config-if-vlan)# ip address dhcp
AW-IHT-1271(config-if-vlan)#
AW-IHT-1271(config)# hostname abc
abc(config)#
SYNTAX
ip arpinspection
ip arp inspection entry interface
ip arp inspection translate [ interface
ip arp inspection vlan
ip arp inspection vlan
ip dhcp excluded-address
ip dhcp pool
ip dhcp relay
ip dhcp relay information option
ip dhcp relay information policy { drop | keep | replace }
ip dhcp server
ip dhcp snooping
ip dns proxy
ip helper-address
ip http secure-redirect
ip http secure-server
ip igmp host-proxy [ leave-proxy ]
ip igmp snooping
ip igmp snooping vlan
ip igmp ssm-range
ip igmp unknown-flooding
ip name-server {
ip route
ip routing
ip source binding interface
ip ssh
ip verify source
ip verify source translate
Parameter
arp Address Resolution Protocol
dhcp Dynamic Host Configuration Protocol
dns Domain Name System
helper-address DHCP relay server
http Hypertext Transfer Protocol
igmp Internet Group Management Protocol
name-server Domain Name System
route Add IP route
routing Enable routing for IPv4 and IPv6
source source command
ssh Secure Shell
verify verify command
inspection ARP inspection
entry arp inspection entry
interface arp inspection entry interface config
Port type in Fast, Giga ethernet
Port ID in the format of switch-no/port-no
Select a VLAN id to configure
Select a MAC address to configure
Select an IP Address to configure
deny log denied entries
permit log permitted entries
all log all entries
translate arp inspection translate all entries
vlan arp inspection vlan setting
arp inspection vlan list
relay DHCP relay agent information
information DHCP information option
option DHCP option
information DHCP information option(Option 82)
policy Policy for handling the receiving DHCP packet already include the information option
drop Drop the package when receive a DHCP message that already contains relay information
keep Keep the original relay information when receive a DHCP message that already contains it
replace Replace the original relay information when receive a DHCP message that already contains
it
server Enable DHCP server
snooping DHCP snooping
proxy DNS proxy service
secure-redirect Secure HTTP web rediction
secure-server Secure HTTP web server
snooping Snooping IGMP
Profile name in 16 char's
vlan IGMP VLAN
ssm-range IPv4 address range of Source Specific Multicast
Valid IPv4 multicast address
<4-32> Prefix length ranges from 4 to 32
unknown-flooding Flooding unregistered IPv4 multicast traffic
A valid IPv4 unicast address
dhcp Dynamic Host Configuration Protocol
interface Select an interface to configure
vlan VLAN Interface
VLAN identifier(s): VID
Network
Netmask
Gateway
binding ip source binding
interface ip source binding entry interface config
* or Gigibitethernet
* All switches or All ports
Gigabitethernet 1 Gigabitethernet Port
Port ID in the format of switch-no/port-no, ex 1/1-12 for Gigabitethernet
Select a VLAN id to configure
Select an IP Address to configure
Select a subnet mask to configure
Select a MAC address to configure
source verify source
limit limit command
<0-2> the number of limit
translate ip verify source translate all entries
loggin ARP inspection vlan loging mode config
EXAMPLE
ipmc
IPv4/IPv6 multicast configuration.
SYNTAX
ipmc profile
ipmc profile
ipmc range
Parameter
profile IPMC profile configuration
range A range of IPv4/IPv6 multicast addresses for the profile
< word16> Range entry name in 16 char's
Valid IPv4 multicast address
Valid IPv6 multicast address
EXAMPLE
AW-IHT-1271(config)# ipmc profile test
AW-IHT-1271(config-ipmc-profile)#
AW-IHT-1271(config)# ip arp inspection
AW-IHT-1271(config)# ip dhcp relay
AW-IHT-1271(config)# ip dns proxy
AW-IHT-1271(config)# ip helper-address 192.168.1.1
AW-IHT-1271(config)# ip http secure-server
AW-IHT-1271(config)# ip igmp snooping vlan 3
AW-IHT-1271(config)# ip name-server 192.168.1.6
AW-IHT-1271(config)# ip route 192.168.1.1 255.255.255.0 192.168.1.100
AW-IHT-1271(config)# ip routing
AW-IHT-1271(config)# ip ssh
AW-IHT-1271(config)# ip verify source translate
IP Source Guard:
Translate 0 dynamic entries into static entries.
ipv6
IPv6 configuration commands
SYNTAX
ipv6 mld host-proxy [ leave-proxy ]
ipv6 mld snooping
ipv6 mld snooping vlan
ipv6 mld ssm-range
ipv6 mld unknown-flooding
ipv6 route
Parameter
mld Multicasat Listener Discovery
route Configure static routes
host-proxy MLD proxy configuration
snooping Snooping MLD
ssm-range IPv6 address range of Source Specific Multicast
unknown-flooding Flooding unregistered IPv6 multicast traffic
leave-proxy MLD proxy for leave configuration
vlan MLD VLAN
VLAN identifier(s): VID
Valid IPv6 multicast address
X:X:X:X::X/<0-128> IPv6 prefix x:x::y/z
EXAMPLE
lacp
LACP settings.
SYNTAX
lacp system-priority <1-65535>
Parameter
system-priority System priority
<1-65535> Priority value, lower means higher priority
EXAMPLE
line
Configure a terminal line.
SYNTAX
line { <0~16> | console 0 | vty <0~15> }
Parameter
<0~16> List of line numbers
console Console terminal line
0 Console Line number
vty Virtual terminal
<0~15> List of vty numbers
AW-IHT-1271(config)# lacp system-priority 333
AW-IHT-1271(config)#
AW-IHT-1271(config)# ipv6 mld host-proxy leave-proxy
AW-IHT-1271(config)# ipv6 mld snooping vlan 1
AW-IHT-1271(config)#
EXAMPLE
lldp
LACP configurations.
SYNTAX
lldp holdtime <2-10>
lldp med datum { wgs84 | nad83_navd88 | nad83_mllw }
lldp med fast <1-10>
lldp med location-tlv altitude { meters | floors }
lldp med location-tlv civic-addr { country | state | county | city | district | block | street | leading-street-direction |
trailing-street-suffix | street-suffix | house-no | house-no-suffix | landmark | additional-info | name | zip-code |
building | apartment | floor | room-number | place-type | postal-community-name | p-o-box | additional-code }
lldp med location-tlv elin-addr
lldp med location-tlv latitude { north | south }
lldp med location-tlv longitude { west | east }
lldp med media-vlan policy-list
lldp med media-vlan-policy <0-31> { voice | voice-signaling | guest-voice-signaling | guest-voice |
softphone-voice | video-conferencing | streaming-video | video-signaling } { tagged
[ l2-priority <0-7> ] [ dscp <0-63> ]
lldp reinit <1-10>
lldp timer <5-32768>
lldp transmission-delay <1-8192>
Parameter
holdtime Sets LLDP hold time (The neighbor switch will
AW-IHT-1271(config)# line console 0
AW-IHT-1271(config-line)#
discarded the LLDP information after "hold time"
multiplied with "timer" seconds ).
med Media Endpoint Discovery.
reinit LLDP tx reinitialization delay in seconds.
timer Sets LLDP TX interval (The time between each LLDP
frame transmitted in seconds).
transmission-delay Sets LLDP transmision-delay. LLDP transmission delay
(the amount of time that the transmission of LLDP
frames will delayed after LLDP configuration has
changed) in seconds.)
<2-10> 2-10 seconds.
<1-10> 1-10 seconds.
<5-32768> 5-32768 seconds.
<1-8192> 1-8192 seconds.
datum Datum (geodetic system) type.
fast Number of times to repeat LLDP frame transmission at
fast start.
location-tlv LLDP-MED Location Type Length Value parameter.
media-vlan-policy Use the media-vlan-policy to create a policy, which
can be assigned to an interface.
nad83_mllw Mean lower low water datum 1983
nad83_navd88 North American vertical datum 1983
wgs84 World Geodetic System 1984
altitude Altitude parameter
meter Altitude value
floors Altitude value
civic-addr Civic address information and postal information
country The two-letter ISO 3166 country code in capital ASCII letters - Example: DK, DE or
US.
state National subdivisions (state, canton, region, province, prefecture).
county County, parish, gun (Japan), district.
city City, township, shi (Japan) - Example: Copenhagen.
district City division, borough, city district, ward, chou (Japan).
block Neighbourhood, block.
street Street - Example: Poppelvej.
leading-street-direction Leading street direction - Example: N.
trailing-street-suffix Trailing street suffix - Example: SW.
street-suffix Street suffix - Example: Ave, Platz.
house-no House number - Example: 21.
house-no-suffix House number suffix - Example: A, 1/2.
landmark Landmark or vanity address - Example: Columbia University.
additional-info Additional location info - Example: South Wing.
name Name (residence and office occupant) - Example: Flemming Jahn.
zip-code Postal/zip code - Example: 2791.
building Building (structure) - Example: Low Library.
apartment Unit (Apartment, suite) - Example: Apt 42.
floor Floor - Example: 4.
room-number Room number - Example: 450F.
place-type Place type - Example: Office.
postal-community-name Postal community name - Example: Leonia.
p-o-box Post office box (P.O. BOX) - Example: 12345.
additional-code Additional code - Example: 1320300003.
Value for the corresponding selected civic address.
elin-addr Emergency Location Identification Number, (e.g. E911 and others), such as defined by TIA
or NENA.
ELIN value
north Setting latitude direction to north.
south Setting latitude direction to south.
Latitude degrees (0.0000-90.0000).
policy-list Assignment of policies.
Policies to assign to the interface.
<0-31> Policy id for the policy which is created.
voice Create a voice policy.
voice-signaling Create a voice signaling policy.
guest-voice-signaling Create a guest voice signaling policy.
guest-voice Create a guest voice policy.
softphone-voice Create a softphone voice policy.
video-conferencing Create a video conferencing policy.
streaming-video Create a streaming video policy.
video-signaling Create a video signaling policy.
tagged The policy uses tagged frames.
The VLAN the policy uses tagged frames.
untagged The policy uses un-tagged frames.
l2-priority Layer 2 priority.
<0-7> Priority 0-7
dscp Differentiated Services Code Point.
<0-63> DSCP value 0-63.
EXAMPLE
logging
Syslog.
SYNTAX
logging host {
logging level { info | warning | error }
logging on
Parameter
host host
IP address of the log server
Donain name of the log server
level level
info Information
warning Warning
error Error
on Enable syslog server
EXAMPLE
AW-IHT-1271(config)# logging level error
AW-IHT-1271(config)# logging on
AW-IHT-1271(config)#
AW-IHT-1271(config)# lldp holdtime 5
AW-IHT-1271(config)# lldp med fast 5
AW-IHT-1271(config)# lldp reinit 3
AW-IHT-1271(config)# lldp timer 555
AW-IHT-1271(config)# lldp transmission-delay 333
Note: According to IEEE 802.1AB-clause 10.5.4.2 the transmission-delay must not
be larger than LLDP timer * 0.25. LLDP timer changed to 13332
loop-protect
Loop protection configuration.
SYNTAX
loop-protect
loop-protect shutdown-time <0-604800>
loop-protect transmit-time<1-10>
Parameter
shutdown-time Loop protection shutdown time interval
<0-604800> Shutdown time in second
transmit-time Loop protection transmit time interval
<1-10> Transmit time in second
EXAMPLE
mac
MAC table entries/configuration.
SYNTAX
mac address-table aging-time <0,10-1000000>
mac address-table static
Parameter
address-table Mac Address Table
aging-time Mac address aging time
AW-IHT-1271(config)# loop-protect
AW-IHT-1271(config)# loop-protect shutdown-time 333
AW-IHT-1271(config)# loop-protect transmit-time 3
AW-IHT-1271(config)#
<0,10-1000000> Aging time in seconds, 0 disables aging
static Static MAC address
48 bit MAC address: xx:xx:xx:xx:xx:xx
vlan VLAN keyword
VLAN IDs 1-4095
interface Select an interface to configure
Port type * or Gigabitethernet
* All switches or All ports
Gigabitethernet 1 Gigabit Ethernet port
Port list in 1/1-12 for Gigabitethernet
EXAMPLE
mep
Maintenance Entity Point
SYNTAX
mep <1-100> ais [ fr1m | fr1s | protect ]
mep <1-100> aps <0-7> [ laps ]
mep <1-100> aps <0-7> ( multi | uni ) { [ laps ] | [ raps ] octet
mep <1-100> cc <0-7> ( fr100s | fr10s | fr1m | fr1s | fr300s | fr6h | fr6m )
mep <1-100> ccm-tlv
mep <1-100> client domain ( evc | lsp | vlan ) flow
[ ais-prio | lck- highest | level ] } | { level <0-7> [ ais-prio | lck-prio ] }
mep <1-100> dm <0-7> { dual [ flow | interval | multi | rdtrp | uni ] } | { flow [ dual | interval | multi | single | uni ] } |
{ interval
| { single [ flow | interval | multi | rdtrp | uni ] } | { uni mep-id
AW-IHT-1271(config)# mac address-table aging-time 3333
AW-IHT-1271(config)#
mep <1-100> down domain [ evc | lsp | port | pw | tp-link | tunnel-tp | vlan ] [ ( flow
mep <1-100> lb <0-7> ( count
Parameter
<1-100> The MEP instance number
os-tlv Organization-Specific TLV
ais Alarm Indication Signal
aps Automatic Protection Switching protocol.
cc Continuity Check.
ccm-tlv The CCM TLV enable/disable
client
dm Delay Measurement.
down This MEP is a Down-MEP
lb Loop Back
lck Locked Signal
level The MEG level of the MEP.
link-state-tracking Link State Tracking. When LST is enabled in an instance, Local SF or received
'isDown' in CCM Interface Status TLV, will bring down the residence port. Only valid
in Up-MEP. The CCM rate must be 1 f/s or faster.
lm Loss Measurement.
lm-avail Availability for Loss Measurement
lm-hli High Loss Interval for Loss Measurement
lm-notif Loss Measurement JSON notifications
lm-sdeg Signal Degrade for Loss Measurement
lt Link Trace.
meg-id The ITU/IEEE MEG-ID.
mep-id The MEP-ID.
mip This MEP instance is a half-MIP.
peer-mep-id The peer MEP-ID.
performance-monitoring Performance monitoring Data Set collection (MEF35).
syslog Enable syslog.
tst Test Signal
up This MEP is a UP-MEP.
vid The MEP VID.
voe MEP is VOE based.
fr1m Frame rate is 1 f/min.
fr1s Frame rate is 1 f/s.
protect The AIS can be used for protection. At the point of state change three AIS PDU
is transmitted as fast as possible.
<0-7> Priority in case of tagged OAM. In the MPLS and EVC domain this is the COS-ID.
laps Linear Automatic Protection Switching protocol.
multi OAM PDU is transmitted with multicast MAC. Must me 'multi' in case of RAPS.
raps Ring Automatic Protection Switching protocol.
uni OAM PDU is transmitted with unicast MAC. The MAC is taken from peer MEP MAC
database. Only possible in case of LAPS.
octet Then last OCTET in the multivast MAC. Only possible in case of RAPS.
Last OCTET value
fr100s Frame rate is 100 f/s.
fr10s Frame rate is 10 f/s.
fr1m Frame rate is 1 f/min.
fr1s Frame rate is 1 f/s.
fr300s Frame rate is 300 f/s.
fr6h Frame rate is 6 f/hour.
fr6m Frame rate is 6 f/min.
domain Client flow domain
evc EVC client flow.
lsp MPLS-TP LSP client flow.
vlan VLAN client flow.
flow Client flow instance.
Client flow instance number value.
ais-prio AIS injection priority.
lck-prio LCK injection priority.
level The MEG level on the client layer.
<0-7> AIS injection priority value.
ais-highest Request the highest possible AIS priority.
lck-highest Request the highest possible LCK priority.
<0-7> The MEG level value.
bin Delay Measurement Binning.
ns Nano Seconds
overflow-reset Reset all Delay Measurement results on total delay counter overflow.
proprietary Proprietary Delay Measurement.
synchronized Near enad and far end is real time synchronized.
dual Delay Measurement based on 1DM PDU transmission.
flow The two way delay is calculated as round trip symmetrical flow delay. The far end
residence time is subtracted.
Interval Interval between PDU transmission in 10ms. Min value is 10.
Multi OAM PDU is transmitted with multicast MAC.
rdtrp The two way delay is calculated as round trip delay. The far end residence time is
not subtracted.
single Delay Measurement based on DMM/DMR PDU.
uni OAM PDU is transmitted with unicast MAC. The MAC is taken from peer MEP MAC
database.
Interval value.
last-n The last N dalays used for average last N calculation. Min value is 10.
mep-id Peer MEP-ID for unicast DM. The MAC is taken from peer MEP MAC database.
Peer MEP-ID value.
domain The domain of the MEP.
evc This MEP is a EVC domain MEP.
lsp This MIP is an MPLS-TP LSP domain MIP.
port This MEP is a Port domain MEP.
pw This MEP is an MPLS-TP Pseudo-Wire domain MEP.
tp-link This MEP is an MPLS-TP link domain MEP.
tunnel-tp This MEP is an MPLS-TP tunnel domain MEP.
vlan This MEP is a VLAN domain MEP
flow In case the MEP is a VLAN, EVC, MPLS-TP link, tunnel, LSP or Pseudo-Wire
domain MEP, the flow instance that the MEP is related to must be given.
level The MEG level of the MEP.
vid In case the MEP is a Port domain Up-MEP or a EVC domain customer MIP (on the
UNI), the VID must be given.
The VLAN, EVC, MPLS-TP link, MPLS-TP tunnel, MPLS-TP LSP or MPLS-TP
Pseudo-Wire flow instance number.
count The number of LBM PDUs to send in one loop test. The value 0 indicate infinite
transmission (test behaviour). This is HW based LBM/LBR and Requires VOE.
dei Drop Eligible Indicator in case of tagged OAM.
mpls Specify optional values for loopback initiated from an MPLS-TP MEP.
Number of LBM PDUs to send value.
ttl Specify Time-To-Live value to be used for the MPLS-TP OAM LBM PDU. Default is
to use TTL value 255.
EXAMPLE
monitor
Set monitor configuration.
SYNTAX
monitor destination interface
monitor source { interface
Parameter
destination The destination port. That is the port that trafficed should be mirrored to.
interface Interface to mirror traffic to.
source The source port. That is the source port to be mirrored to the destination port.
interface Mirrot interface traffic.
1 Gigabit Ethernet port
* All switches or all ports
Port list in 1/1-12.
cpu Mirrot CPU traffic.
both Setting source port to both will mirror both ingress and egress traffic.
rx Setting source port to rx will mirror bothingress traffic.
AW-IHT-1271(config)# mep 1 cc 3 fr1m
AW-IHT-1271(config)#
AW-IHT-1271(config)# mep 1 ccm-tlv
AW-IHT-1271(config)#
tx Setting source port to tx will mirror both egress traffic.
Port type in Gigabitethernet
Port list in 1/1-12 for Gigabitethernet
EXAMPLE
mvr
Multicast VLAN Registration configuration.
SYNTAX
mvr
mvr name
mvr name
mvr name
mvr name
mvr name
mvr name
mvr vlan
mvr vlan
mvr vlan
mvr vlan
mvr vlan
mvr vlan
mvr vlan
Parameter
AW-IHT-1271(config)# monitor destination interface GigabitEthernet 1/8
AW-IHT-1271(config)# monitor source cpu both
AW-IHT-1271(config)#
name MVR multicast name
MVR multicast VLAN name
channel MVR channel configuration
Profile name in 16 char's
frame MVR control frame in TX
priority Interface CoS priority
<0-7> CoS priority ranges from 0 to 7
tagged Tagged IGMP/MLD frames will be sent
igmp-address MVR address configuration used in IGMP
> A valid IPv4 unicast address MVR multicast VLAN name
last-member-query-interval Last Member Query Interval in tenths of seconds
<0-31744> 0 - 31744 tenths of seconds
mode MVR mode of operation
dynamic Dynamic MVR operation mode
compatible Compatible MVR operation mode
vlan MVR multicast vlan
MVR multicast VLAN list
channel MVR channel configuration
Profile name in 16 char's
frame MVR control frame in TX
priority Interface CoS priority
<0-7> CoS priority ranges from 0 to 7
igmp-address MVR address configuration used in IGMP
A valid IPv4 unicast address
MVR multicast VLAN list
last-member-query-interval Last Member Query Interval in tenths of seconds
<0-31744> 0 - 31744 tenths of seconds
compatible Compatible MVR operation mode
EXAMPLE
no
Negate a command or set its defaults
Table : configure no Commands
Command Function
aaa Authentication, Authorization and Accounting
access Access management
access-list Access list
aggregation Aggregation mode
banner Define a login banner
clock Configure time-of-day clock
debug Debugging functions
dot1x IEEE Standard for port-based Network Access Control
enable Modify enable password parameters
eps Ethernet Protection Switching.
erps Ethernet Ring Protection Switching
evc Ethernet Virtual Connections
green-ethernet Green ethernet (Power reduction)
gvrp Enable GVRP feature
hostname Set system's network name
interface none
ip Internet Protocol
ipmc IPv4/IPv6 multicast configuration
ipv6 IPv6 configuration commands
lacp LACP settings
lldp LLDP configurations.
logging Syslog
loop-protect Loop protection configuration
mac MAC table entries/configuration
AW-IHT-1271(config)# mvr vlan 10 mode dynamic
AW-IHT-1271(config)#
mep Maintenance Entity Point
monitor Set monitor configuration.
mvr Multicast VLAN Registration configuration
ntp Configure NTP
poe Power Over Ethernet
port-security Enable/disable port security globally.
Privilege Command privilege parameters
ptp Precision time Protocol (1588)
qos Quality of Service
radius-server Configure RADIUS
rmon Remote Monitoring
sflow Statistics flow.
snmp-server Enable SNMP server
spanning-tree STP Bridge
switchalert-management SwitchAlert Management configuration
switchport VLAN
system Set the SNMP server's configurations
tacacs-server Configure TACACS+
udld Disable UDLD configurations on all fiber-optic
ports.
upnp Set UPnP's configurations
username Establish User Name Authentication
vlan Vlan commands
voice Voice appliance attributes
web Web
aaa
Authentication, Authorization and Accounting
SYNTAX
no aaa authentication login { console | telnet | ssh | http }
Parameter
authentication Authentication
login Login
console Disable Console
http Disable HTTP
ssh Disable SSH
telnet Disable Telnet
EXAMPLE
access
Access management
SYNTAX
no access management [<1~16>]
no access management
Parameter
management Access management configuration
<1~16> ID of access management entry
EXAMPLE
access-list
Access list
SYNTAX
no access-list ace <1~256>
Parameter
ace Access list entry
ACE ID
AW-IHT-1271(config)# no access management
AW-IHT-1271(config)#
AW-IHT-1271(config)# no aaa authentication login ssh
AW-IHT-1271(config)#
EXAMPLE
aggregation
Aggregation mode
SYNTAX
no aggregation mode
Parameter
mode Traffic distribution mode
EXAMPLE
banner
Define a login banner
SYNTAX
no banner [ motd ]
no banner exec
no banner login
Parameter
exec Set EXEC process creation banner
login Set login banner
motd Set Message of the Day banner
EXAMPLE
AW-IHT-1271(config)# no aggregation mode
AW-IHT-1271(config)#
AW-IHT-1271(config)# access-list ace 1
AW-IHT-1271(config)#
clock
Configure time-of-day clock
SYNTAX
no clock summer-time
no clock timezone
Parameter
summer-time Configure summer (daylight savings) time
timezone Configure time zone
EXAMPLE
debug
Debugging functions
SYNTAX
no debug mep
no debug mep
no debug mep
no debug mep
no debug mep
no debug mep
no debug mep
no debug mep
AW-IHT-1271(config)# no clock summer-time
AW-IHT-1271(config)# no clock timezone
AW-IHT-1271(config)#
AW-IHT-1271(config)# no banner login
AW-IHT-1271(config)#
no debug mep
no debug mep
no debug mep
Parameter
mep Maintenance Entity Point.
The MEP instance number.
dm Delay Measurement.
test Test Generation.
volatile The MEP instance is change to volatile.
tx Transmit DM/1DM.
dual Dual ended - 1DM based.
single Single ended - DMM/DMR based.
<0-7> Priority in case of tagged OAM. In the EVC domain this is the COS-ID.
interval Interval between PDU transmission in 10ms. Min value is 10.
synchronized Near enad and far end is real time synchronized.
Interval value.
tx Transmit Test.
EXAMPLE
dot1x
IEEE Standard for port-based Network Access Control
SYNTAX
AW-IHT-1271(config)# no debug mep 1 dm tx dual 0
AW-IHT-1271(config)#
AW-IHT-1271(config)# no debug mep 1 volatile
AW-IHT-1271(config)#
no dot1x authentication timer inactivity
no dot1x authentication timer re-authenticate
no dot1x feature { [ guest-vlan ] [ radius-qos ] [ radius-vlan ] }
no dot1x guest-vlan [supplicant]
no dot1x max-reauth-req
no dot1x re-authentication
no dot1x system-auth-control
no dot1x timeout quiet-period
no dot1x timeout tx-period
Parameter
authentication Authentication
feature Globally enables/disables a dot1x feature
functionality
guest-vlan Guest VLAN
max-reauth-req The number of time a Request Identity EAPOL frame is sent without response before
considering entering the Guest VLAN.
re-authentication Set Re-authentication state
system-auth-control Set the global NAS state
timeout timeout
timer timer
inactivity Time in seconds between check for activity on
successfully authenticated MAC addresses.
re-authenticate The period between re-authentication attempts in seconds
guest-vlan Globally enables/disables state of guest-vlan
radius-qos Globally enables/disables state of RADIUS-assigned QoS.
radius-vlan Globally enables/disables state of RADIUS-assigned VLAN.
supplicant The switch remembers if an EAPOL frame has been received on
the port for the life-time of the port. Once the switch
considers whether to enter the Guest VLAN, it will first
check if this option is enabled or disabled. If disabled
(unchecked; default), the switch will only enter the Guest
VLAN if an EAPOL frame has not been received on the port for
the life-time of the port. If enabled (checked), the switch
will consider entering the Guest VLAN even if an EAPOL frame
has been received on the port for the life-time of the port.
quiet-period Time in seconds before a MAC-address that failed
authentication gets a new authentication chance.
tx-period the time between EAPOL retransmissions.
EXAMPLE
enable
Modify enable password parameters
SYNTAX
no enable password [ level <1-15> ]
no enable secret [0|5 { level <1-15> }]
AW-IHT-1271(config)# no dot1x authentication timer inactivity
AW-IHT-1271(config)# no dot1x feature guest-vlan radius-qos radius-vlan
AW-IHT-1271(config)# no dot1x guest-vlan supplicant
AW-IHT-1271(config)# no dot1x max-reauth-req
AW-IHT-1271(config)# no dot1x re-authentication
AW-IHT-1271(config)# no dot1x system-auth-control
AW-IHT-1271(config)# no dot1x timeout tx-period
AW-IHT-1271(config)#
Parameter
password Assign the privileged level clear password
secret Assign the privileged level secret
0 Specifies an UNENCRYPTED password will follow
5 Specifies an ENCRYPTED password will follow
level Set exec level password
<1-15> Level number
EXAMPLE
eps
Ethernet Protection Switching.
SYNTAX
no eps
no eps
Parameter
The EPS instance number.
command Clear command on EPS.
holdoff
revertive Revertive EPS.
EXAMPLE
AW-IHT-1271(config)# no eps 1
AW-IHT-1271(config)#
AW-IHT-1271(config)# no enable secret level 15
AW-IHT-1271(config)# no enable password level 15
AW-IHT-1271(config)#
erps
Ethernet Ring Protection Switching
SYNTAX
no erps 1-64 [ guard | holdoff | mep | revertive | rpl | ( topology Change propagate
) | version | vlan ]
Parameter
1-64 ERPS group number
guard Guard
holdoff Hold-off
mep MEP
revertive
rpl Ring Protection Link
topology-change Topology Change
version Version
vlan VLAN.
propagate Propagate
EXAMPLE
evc
Ethernet Virtual Connections
SYNTAX
AW-IHT-1271(config)# no erps 1 vlan
AW-IHT-1271(config)#
no evc [ <1-256> ] | [ ece <1-256> ]
Parameter
<1-256> EVC identifier
ece EVC Control Entry
EXAMPLE
Green-ethernet
Green ethernet (Power reduction)
SYNTAX
no green-ethernet eee optimize-for-power
Parameter
eee Powering down of PHYs when there is no traffic.
optimize-for-power Set if EEE shall be optimized for least power consumption (else optimized for least
traffic latency).
EXAMPLE
gvrp
Enable GVRP feature.
SYNTAX
AW-IHT-1271(config)# no green-ethernet eee optimize-for-power
AW-IHT-1271(config)#
AW-IHT-1271(config)# no evc ece 1
AW-IHT-1271(config)#
gvrp
gvrp max-vlans
gvrp time { [ join-time
Parameter
max-vlans Number of simultaniously VLANs that GVRP can control
time Config GARP protocol timer parameters. IEEE 802.1D-2004, clause 12.11.
join-time Set GARP protocol parameter JoinTime. See IEEE 802.1D-2004, clause 12.11
leave-all-time Set GARP protocol parameter LeaveAllTime. See IEEE 802.1D-2004, clause 12.11
leave-time Set GARP protocol parameter LeaveTime. See IEEE 802.1D-2004, clause 12.11
EXAMPLE
hostname
Set system's network name.
SYNTAX
no hostname
EXAMPLE
interface
SYNTAX
no interface vlan < vlan_list >
AW-IHT-1271(config)# no hostname
AW-IHT-1271(config)#
AW-IHT-1271(config)#no gvrp max-vlans 1
AW-IHT-1271(config)#no gvrp time join-time 10
AW-IHT-1271(config)#no gvrp time leave-all-time 2000
AW-IHT-1271(config)#no gvrp time leave-time 70
AW-IHT-1271(config)#
Parameter
vlan Vlan interface configurations
Vlan list
EXAMPLE
Ip
Set system's network name.
SYNTAX
no ip arp inspection
no ip arp inspection entry interface Gigabitethernet
no ip arp inspection vlan
no dhcp execluded-address [
no dhcp pool
no ip dhcp relay [information {option| policy }]
no ip dhcp server
no ip dhcp snooping
no ip dns proxy
no ip helper-address
no ip http secure-redirect
no ip http secure-server
no ip igmp host-proxy [ leave-proxy ]
no ip igmp snooping
no ip igmp snooping vlan [
no ip igmp ssm-range
AW-IHT-1271(config)# no interface vlan 10
AW-IHT-1271(config)#
no ip igmp unknown-flooding
no ip name-server
no ip route
no ip routing
no ip source binding interface Gigabitethernet
no ip ssh
no ip verify source
Parameter
arp Address Resolution Protocol
inspection ARP inspection
entry arp inspection entry
interface arp inspection entry interface config
GigabitEthernet 1 Gigabit Ethernet Port
Port ID in the format of switch-no/port-no, 1/1-12 for Gigabitetherne
Select a VLAN id to configure
Select a MAC address to configure
Select an IP Address to configure
vlan arp inspection vlan setting
arp inspection vlan list
logging ARP inspection vlan logging mode config
dhcp Dynamic Host Configuration Protocol
execluded-address Prevent DHCP from assigning certain address
Low IP address and High IP address
Pool name in 32 characters
pool Configure DHCP address pools
relay DHCP relay agent configuration
server enable DHCP server
snoping DHCP snooping
information DHCP information option(Option 82)
option DHCP option
policy Policy for handling the receiving DHCP packet already include the information option
snooping DHCP snooping
dns Domain Name System
proxy DNS proxy service
helper-address None.
http Hypertext Transfer Protocol
secure-redirect Secure HTTP web rediction
secure-server Secure HTTP web server
igmp Internet Group Management Protocol
host-proxy IGMP proxy configuration
leave-proxy IGMP proxy for leave configuration
snooping Snooping IGMP
vlan IGMP VLAN
VLAN identifier(s): VID
ssm-range IPv4 address range of Source Specific Multicast
unknown-flooding Flooding unregistered IPv4 multicast traffic
name-server Domain Name System
Route none
Network
Netmask
Gateway
routing Disable routing for IPv4 and IPv6
source source command
binding ip source binding
interface ip source binding entry interface config
Gigabitethernet 1 Gigabitethernet port
Port ID in the format of switch-no/port-no, ex., 1/1-12 for Gigabitethernet
Select a VLAN id to configure
Select an IP Address to configure
Select a subnet mask to configure
Select a MAC address to configure
ssh Secure Shell
verify verify command
source verify source
EXAMPLE
ipmc
AW-IHT-1271(config)# no ip arp inspection vlan 3 logging
AW-IHT-1271(config)# no ip dhcp relay information option
AW-IHT-1271(config)# no ip dns proxy
AW-IHT-1271(config)# no ip helper-address
AW-IHT-1271(config)# no ip http secure-redirect
AW-IHT-1271(config)# no ip igmp snooping
AW-IHT-1271(config)# no ip name-server
AW-IHT-1271(config)# no ip routing
AW-IHT-1271(config)# no ip ssh
AW-IHT-1271(config)# no ip verify source
AW-IHT-1271(config)#
IPv4/IPv6 multicast configuration
SYNTAX
no ipmc profile
no ipmc range
Parameter
profile IPMC profile configuration
Profile name in 16 char's
range A range of IPv4/IPv6 multicast addresses for the profile
Range entry name in 16 char's
EXAMPLE
ipv6
IPv6 configuration commands
SYNTAX
no ipv6 mld host-proxy [ leave-proxy ]
no ipv6 mld snooping
no ipv6 mld snooping [vlan
no ipv6 mld ssm-range
no ipv6 mld unknown-flooding
no ipv6 route
Parameter
mld Multicasat Listener Discovery
host-proxy MLD proxy configuration
AW-IHT-1271(config)# no ipmc profile
leave-proxy MLD proxy for leave configuration
snooping Snooping MLD
vlan MLD VLAN
VLAN identifier(s): VID
ssm-range IPv6 address range of Source Specific Multicast
unknown-flooding Flooding unregistered IPv6 multicast traffic
route Configure static routes
IPv6 prefix x:x::y/z
IPv6 unicast address (except link-local address) of next-hop
interface Select an interface to configure
vlan VLAN Interface
VLAN identifier(s): VID
IPv6 link-local address of next-hop
EXAMPLE
lacp
LACP settings
SYNTAX
no lacp system-priority <1-65535>
Parameter
system-priority System priority
<1-65535> Priority value, lower means higher priority
EXAMPLE
AW-IHT-1271(config)# no ipv6 mld snooping
AW-IHT-1271(config)#
lldp
LLDP configurations..
SYNTAX
no lldp holdtime
no lldp med datum
no lldp med fast
no lldp med location-tlv altitude
no lldp med location-tlv civic-addr { country | state | county | city | district | block | street | leading-street-direction |
trailing-street-suffix | street-suffix | house-no | house-no-suffix | landmark | additional-info | name | zip-code |
building | apartment | floor | room-number | place-type | postal-community-name | p-o-box | additional-code }
no lldp med location-tlv elin-addr
no lldp med location-tlv latitude
no lldp med location-tlv longitude
no lldp med media-vlan-policy <0~31>
no lldp reinit
no lldp timer
no lldp transmission-delay
Parameter
holdtime Sets LLDP hold time (The neighbor switch will
discarded the LLDP information after "hold time"
multiplied with "timer" seconds ).
med Media Endpoint Discovery.
reinit Sets LLDP reinitialization delay.
AW-IHT-1271(config)# no lacp system-priority 10000
AW-IHT-1271(config)#
timer Sets LLDP TX interval (The time between each LLDP
frame transmitted in seconds).
tlv-select Which optional TLVs to transmit.
transmission-delay Sets LLDP transmision-delay. LLDP transmission delay
(the amount of time that the transmission of LLDP
frames will delayed after LLDP configuration has
changed) in seconds.)
datum Set datum to default value.
fast Set fast repeat count to default value.
location-tlv LLDP-MED Location Type Length Value parameter.
media-vlan-policy Use the media-vlan-policy to create a policy, which
can be assigned to an interface.
altitude Setting altitude to default.
civic-addr Civic address information and postal information
elin-addr Set elin address to default value.
latitude Setting Latitude parameter to default.
longitude Setting longitude to default.
additional-code Additional code - Example: 1320300003.
additional-info Additional location info - Example: South Wing.
apartment Unit (Apartment, suite) - Example: Apt 42.
block Neighbourhood, block.
building Building (structure) - Example: Low Library.
city City, township, shi (Japan) - Example: Copenhagen.
country The two-letter ISO 3166 country code in capital
ASCII letters - Example: DK, DE or US.
county County, parish, gun (Japan), district.
district City division, borough, city district, ward, chou (Japan).
floor Floor - Example: 4.
house-no House number - Example: 21.
house-no-suffix House number suffix - Example: A, 1/2.
landmark Landmark or vanity address - Example: Columbia University.
leading-street-direction Leading street direction - Example: N.
name Name (residence and office occupant) - Example: Flemming Jahn.
p-o-box Post office box (P.O. BOX) - Example: 12345.
place-type Place type - Example: Office.
postal-community-name Postal community name - Example: Leonia.
room-number Room number - Example: 450F.
state National subdivisions (state, canton, region, province, prefecture).
street Street - Example: Poppelvej.
street-suffix Street suffix - Example: Ave, Platz.
trailing-street-suffix Trailing street suffix - Example: SW.
zip-code Postal/zip code - Example: 2791.
<0~31> Policy to delete.
EXAMPLE
logging
AW-IHT-1271(config)# no lldp holdtime
AW-IHT-1271(config)# no lldp med location-tlv civic-addr floor
AW-IHT-1271(config)# no lldp reinit
AW-IHT-1271(config)# no lldp timer
AW-IHT-1271(config)# no lldp transmission-delay
AW-IHT-1271(config)#
Syslog.
SYNTAX
no logging host
no logging on
Parameter
host host
on Enable syslog server
EXAMPLE
loop-protect
Loop protection configuration
SYNTAX
no loop-protect
no loop-protect shutdown-time
no loop-protect transmit-time
Parameter
shutdown-time Loop protection shutdown time interval
transmit-time Loop protection transmit time interval
EXAMPLE
AW-IHT-1271(config)# no loop-protect shutdown-time
AW-IHT-1271(config)# no loop-protect transmit-time
AW-IHT-1271(config)#
AW-IHT-1271(config)# no logging host
AW-IHT-1271(config)# no logging on
AW-IHT-1271(config)#
mac
MAC table entries/configuration
SYNTAX
no mac address-table aging-time [<0,10-1000000> ]
no mac address-table static
Parameter
address-table Mac table entries configuration/table
aging-time Mac address aging time
<0,10-1000000> Aging time in seconds, 0 disables aging
static Static MAC address
48 bit MAC address: xx:xx:xx:xx:xx:xx
vlan VLAN keyword
VLAN IDs 1-4095
interface Select an interface to configure
Gigabitethernet 1 Gigabit Ethernet port
Port list in 1/1-12 for Gigaethernet
EXAMPLE
mep
Maintenance Entity Point
SYNTAX
no mep
performance-monitoring | syslog | vid | voe ]
AW-IHT-1271(config)# no mac address-table aging-time 10000
AW-IHT-1271(config)#
no mep
no mep
no mep
no mep
no mep
no mep
no mep
no mep
no mep
Parameter
The MEP instance number.
aging-time Mac address aging time
ais Alarm Indication Signal.
aps Automatic Protection Switching protocol.
cc Continuity Check.
ccm-tlv The CCM TLV enable/disable
client Client flow instance number.
dm Delay Measurement.
lb Loop Back.
lck Locked Signal
link-state-tracking Link State Tracking. When LST is enabled in an instance, Local SF or
received 'isDown' in CCM Interface Status TLV, will bring down the
residence port. Only valid in Up-MEP. The CCM rate must be 1 f/s or
faster.
lm Loss Measurement.
lm-avail Availability for Loss Measurement.
lm-hli High Loss Interval for Loss Measurement.
lm-notif Loss Measurement JSON notifications
lm-sdeg Signal Degrade for Loss Measurement.
lt Link Trace.
peer-mep-id The peer MEP-ID.
performance-monitoring Performance monitoring Data Set collection (MEF35).
syslog Enable syslog.
tst Test Signal.
vid
voe MEP is VOE based.
domain Client flow domain.
evc EVC client flow.
lsp MPLS-TP LSP client flow.
vlan VLAN client flow.
flow Client flow instance.
Client flow instance number value.
all Delete all client flow instances.
bin Delay Measurement Binning.
ns Nano Seconds
overflow-reset Reset all Delay Measurement results on total delay counter overflow.
proprietary Proprietary Delay Measurement.
synchronized Near enad and far end is real time synchronized.
fd the number of FD Measurement Bins.
ifdv the number of IFDV Measurement Bins.
threshold the threshold for each Delay Measurement Binning.
<2-10> the number of FD Measurement Bins.
<1-50000> the threshold for each Delay Measurement Binning.
flow-counting Loss Measurement is counting service frames per flow - all priority in one.
oam-counting Loss Measurement is counting OAM frames either as Y1731 or all
all Loss Measurement is counting all OAM frames as service frames.
y1731 Loss Measurement is counting OAM frames as service frames as described
in Y1731.
maintenance Availability Maintenance indicator.
The peer MEP-ID value.
all All peer MEP-ID will be deleted.
rx Receive Test Signal.
tx Transmit Test Signal.
EXAMPLE
monitor
Set monitor configuration.
SYNTAX
no monitor destination
no monitor source { interface Gigabitethernet
Parameter
Destination
source The source port(s). That is the ports to be mirrored to the destination port.l
cpu Mirror CPU traffic.
AW-IHT-1271(config)# no mep 1 client domain evc flow all
AW-IHT-1271(config)#
AW-IHT-1271(config)# no mep 1 dm bin fd 2
AW-IHT-1271(config)#
interface Mirror Interface traffic.
Gigabitethernet 1 Gigabit Ethernet Port
Port list in 1/1-12 for Gigabitethernet
EXAMPLE
mvr
Multicast VLAN Registration configuration.
SYNTAX
no mvr
no mvr name
no mvr name
no mvr name
no mvr name
no mvr name
no mvr name
no mvr vlan
no mvr vlan
no mvr vlan
no mvr vlan
no mvr vlan
no mvr vlan
no mvr vlan
Parameter
AW-IHT-1271(config)# no monitor destination
AW-IHT-1271(config)# no monitor source cpu
AW-IHT-1271(config)#
name MVR multicast name
MVR multicast VLAN name
channel MVR channel configuration
frame MVR control frame in TX
priority Interface CoS priority
tagged Tagged IGMP/MLD frames will be sent
igmp-address MVR address configuration used in IGMP
last-member-query-interval Last Member Query Interval in tenths of seconds
mode MVR mode of operation
vlan MVR multicast vlan
MVR multicast VLAN list
EXAMPLE
ntp
Configure NTP.
SYNTAX
no ntp
no ntp server <1-5>
Parameter
server Configure NTP server
<1-5> index number
EXAMPLE
AW-IHT-1271(config)# no ntp server 2
AW-IHT-1271(config)#
AW-IHT-1271(config)# no mvr vlan 12 mode
AW-IHT-1271(config)#
poe
Power Over Ethernet.
SYNTAX
no poe [ ( management mode ) | ping-check | { [ profile ] ( id <1-16> ) } | reboot-chip ]
Parameter
management POE_MANAGEMENT_MODE_HELP
ping-check Enable POE Ping Check.
profile erase poe scheduling profile
reboot-chip erase all poe reboot scheduling
mode mode
id erase poe scheduling profile id
<1-16> profile id from 1 to 16
EXAMPLE
port-security
Enable/disable port security globally.
SYNTAX
no port-security
no port-security aging
no port-security aging time
Parameter
aging Enable/disable port security aging.
AW-IHT-1271(config)# no poe profile id 1
AW-IHT-1271(config)#
time Time in seconds between check for activity on learned MAC addresses.
EXAMPLE
privilege
Command privilege parameters
SYNTAX
no privilege
Parameter
Valid words are 'config-vlan' 'configure' 'dhcp-pool' 'exec' 'if-vlan' 'interface' 'ipmc-profile'
'line' 'snmps-host' 'stp-aggr'
level Set privilege level of command
<0-15> Privilege level
Initial valid words and literals of the command to modify, in 128 characters
EXAMPLE
ptp
Precision time Protocol (1588)
SYNTAX
no ptp <0-3> [ clk | domain | filter | ho | log | priority1 | priority2 | p2ptransparent |
AW-IHT-1271(config)# no privilege config-vlan
AW-IHT-1271(config)#
AW-IHT-1271(config)# no port-security aging time
AW-IHT-1271(config)#
no ptp <0-3> mode [ bcfrontend | boundary | e2etransparent | master | slave ]
no ptp <0-3> servo [ ad | ai | ap | displaystates | phase-mode ]
no ptp <0-3> uni <0-4>
no ptp [ ext | system-time ]
Parameter
<0-3> Instance number: 0-3
ext Set the 1PPS and External clock output configuration and vcxo frequency rate
adjustment option to default values
system-time Disable synchronization between PTP and System time
clk Set PTP slave clock options, to freerunning
domain Default Clock domain
filter Set PTP clock filter data to default values
ho Reset PTP Servo holdover parameters to default values
log Disable the PTP debug logging
mode Delete PTP clock instance
priority1 Default Clock priority 1
priority2 Default Clock priority 2
servo Set Servo parameters
uni Clear a Unicast Slave configuration entry
bcfrontend Delete if Boundary clock frontend
boundary Delete if boundary clock
e2etransparent Delete if e2e TC
master Delete if master only
p2ptransparent Delete if p2p TC
slave Delete if slaveonly
ad Disable 'P' parameter in the servo
ai Disable 'P' parameter in the servo
ap Disable 'P' parameter in the servo
displaystates Enable logging of servo parameters on the console
phase-mode Disable phase mode in the servo
<0-4> [0..4] Index in the slave table
EXAMPLE
qos
Quality of Service
SYNTAX
no qos map cos-dscp <0-7> dpl 0-1
no qos map [ dscp-classify | dscp-cos | dscp-egress-translation | dscp-ingress-translation ] [ <0-63> | af11 | af12 |
af13 | af21 | af22 | af23 | af31 | af32 | af33 | af41 | af42 | af43 | be | cs1 | cs2 | cs3 | cs4 | cs5 | cs6 | cs7 | ef | va ]
no qos qce 1-256
no qos storm [ broadcast | multicast | unicast ]
Parameter
map Global QoS Map/Table
qce QoS Control Entry
storm Storm policer
cos-dscp Map for COS to DSCP
dscp-classify Map for DSCP classify enable
dscp-cos Map for DSCP to COS
dscp-egress-translation Map for DSCP egress translation
AW-IHT-1271(config)# no ptp 0 uni 1
AW-IHT-1271(config)#
dscp-ingress-translation Map for DSCP ingress translation
<0~7> Specific class of service or range
dpl Specify drop precedence level
0~1 Specific drop precedence level or range
<0~63> Specific DSCP or range
af11 Assured Forwarding PHB AF11(DSCP 10)
af12 Assured Forwarding PHB AF12(DSCP 12)
af13 Assured Forwarding PHB AF13(DSCP 14)
af21 Assured Forwarding PHB AF21(DSCP 18)
af22 Assured Forwarding PHB AF22(DSCP 20)
af23 Assured Forwarding PHB AF23(DSCP 22)
af31 Assured Forwarding PHB AF31(DSCP 26)
af32 Assured Forwarding PHB AF32(DSCP 28)
af33 Assured Forwarding PHB AF33(DSCP 30)
af41 Assured Forwarding PHB AF41(DSCP 34)
af42 Assured Forwarding PHB AF42(DSCP 36)
af43 Assured Forwarding PHB AF43(DSCP 38)
be Default PHB(DSCP 0) for best effort traffic
cs1 Class Selector PHB CS1 precedence 1(DSCP 8)
cs2 Class Selector PHB CS2 precedence 2(DSCP 16)
cs3 Class Selector PHB CS3 precedence 3(DSCP 24)
cs4 Class Selector PHB CS4 precedence 4(DSCP 32)
cs5 Class Selector PHB CS5 precedence 5(DSCP 40)
cs6 Class Selector PHB CS6 precedence 6(DSCP 48)
cs7 Class Selector PHB CS7 precedence 7(DSCP 56)
ef Expedited Forwarding PHB(DSCP 46)
va Voice Admit PHB(DSCP 44)
1~256 QCE ID
broadcast Police broadcast frames
multicast Police multicast frames
unicast Police unicast frames
EXAMPLE
radius-server
Configure RADIUS.
SYNTAX
no radius-server attribute {32 | 4 | 95}
no radius-server deadtime
no radius-server host {
<0-65535> ]
no radius-server key
no radius-server retransmit
no radius-server timeout
Parameter
Attribute
deadtime Time to stop using a RADIUS server that doesn't respond
host Specify a RADIUS server
key Set RADIUS encryption key
AW-IHT-1271(config)# no qos storm unicast
AW-IHT-1271(config)#
retransmit Specify the number of retries to active server
timeout Time to wait for a RADIUS server to reply
EXAMPLE
rmon
Remote Monitoring.
SYNTAX
no rmon alarm
no rmon event
Parameter
alarm Configure an RMON alarm
event Configure an RMON event
Alarm entry ID
Event entry ID
EXAMPLE
sflow
Statistics flow.
SYNTAX
AW-IHT-1271(config)# no rmon alarm 1000
AW-IHT-1271(config)#
AW-IHT-1271(config)# no radius-server attribute 4
AW-IHT-1271(config)# no radius-server deadtime
AW-IHT-1271(config)# no radius-server key
AW-IHT-1271(config)# no radius-server retransmit
AW-IHT-1271(config)# no radius-server timeout
AW-IHT-1271(config)#
no sflow agent-ip
no sflow collector-address
no sflow collector-port
no sflow max-datagram-size
no sflow timeout
Parameter
agent-ip Sets the agent IP address used as agent-address in UDP
datagrams to 127.0.0.1.
collector-address Collector address
collector-port Collector UDP port
max-datagram-size Maximum datagram size.
timeout Receiver timeout measured in seconds. The switch
decrements the timeout once per second, and as long as
it is non-zero, the receiver receives samples. Once
the timeout reaches 0, the receiver and all its
configuration is reset to defaults.
EXAMPLE
snmp-server
Enable SNMP server.
SYNTAX
AW-IHT-1271(config)# no sflow agent-ip
AW-IHT-1271(config)# no sflow collector-address
AW-IHT-1271(config)# no sflow collector-port
AW-IHT-1271(config)# no sflow max-datagram-size
AW-IHT-1271(config)# no sflow timeout
AW-IHT-1271(config)#
no snmp-server
no snmp-server access
no snmp-server community v2c
no snmp-server community v3
no snmp-server contact
no snmp-server engined-id local
no snmp-server host
no snmp-server location
no snmp-server security-to-group model { v1 | v2c | v3 } name
no snmp-server trap
no snmp-server user
no snmp-server version
no snmp-server view
Parameter
access access configuration
group name
model security model
v1 v1 security model
v2c v2c security model
v3 v3 security model
any any security model
level security level
auth authNoPriv Security Level
noauth noAuthNoPriv Security Level
priv authPriv Security Level
community Set the SNMP community
contact Clear the SNMP server's contact string
engined-id Set SNMP engine ID
host Set SNMP host's configurations
location Clear the SNMP server's location string
security-to-group security-to-group configuration
trap Set trap's configurations
user user who can access SNMP server
version Set the SNMP server's version
view MIB view configuration
local Set SNMP local engine ID
Name of the host configuration
model security model
v1 v1 security model
v2c v2c security model
v3 v3 security model
name security user
security user name
name of user
engine-id engine ID
engine ID octet string
MIB view name
MIB view OID
EXAMPLE
spanning-tree
STP Bridge.
SYNTAX
no spanning-tree edge bpdu-filter
no spanning-tree edge bpdu-guard
no spanning-tree mode
no spanning-tree mst
no spanning-tree mst
no spanning-tree mst forward-time
no spanning-tree mst max-age
no spanning-tree mst max-hops
no spanning-tree mst name
no spanning-tree recovery interval
no spanning-tree transmit hold-count
Parameter
edge Edge ports
AW-IHT-1271(config)# no snmp-server access 333 model any level auth
AW-IHT-1271(config)# no snmp-server community v2c
AW-IHT-1271(config)# no snmp-server engined-id local
AW-IHT-1271(config)# no snmp-server host 333
AW-IHT-1271(config)# no snmp-server location
AW-IHT-1271(config)# no snmp-server security-to-group model v2c name 132
AW-IHT-1271(config)# no snmp-server trap
AW-IHT-1271(config)# no snmp-server version
AW-IHT-1271(config)#
mode STP protocol mode
mst STP bridge instance
recovery The error recovery timeout
transmit BPDUs to transmit
bpdu-filter Enable BPDU filter (stop BPDU tx/rx)
bpdu-guard Enable BPDU guard
instance 0-7 (CIST=0, MST2=1...)
priority Priority of the instance
forward-time Delay between port states
max-age Max bridge age before timeout
max-hops MSTP bridge max hop count
name Name keyword
vlan VLAN keyword
interval The interval
hold-count Max number of transmit BPDUs per sec
1-10 per sec, 6 is default
EXAMPLE
switchalert-management
SwitchAlert Management configuration
AW-IHT-1271(config)# no spanning-tree edge bpdu-filter
AW-IHT-1271(config)# no spanning-tree mode
AW-IHT-1271(config)# no spanning-tree mst max-age
AW-IHT-1271(config)# no spanning-tree recovery interval
AW-IHT-1271(config)# no spanning-tree transmit hold-count
AW-IHT-1271(config)#
SYNTAX
no switchalert-management port-name interface [ * | GigabitEthernet ]
Parameter
port-name Interface specific description
interface Select an interface to configure
* All switches or All ports
GigabitEthernet 1 Gigabit Ethernet Port
Port list for all port types
Port list in 1/1-12
EXAMPLE
switchport
VLAN
SYNTAX
no switchport vlan mapping <1-12>
Parameter
vlan Add VLAN translation entry into a group.
mapping Group id
<1-12>
EXAMPLE
AW-IHT-1271(config)# no switchalert-management port-name interface *
AW-IHT-1271(config)#
system
Set the system description
SYNTAX
no system [ contact | description | location | name | reboot ]
Parameter
contact Clear the SNMP server's contact string
description Clear the system description string
location Clear the SNMP server's location string
name Clear the SNMP server's system model name string
reboot erase all Switch Reboot scheduling
EXAMPLE
tacacs-server
Configure TACACS+.
SYNTAX
no tacacs-server deadtime
AW-IHT-1271(config)# no switchport vlan mapping 1 12
AW-IHT-1271(config)#
AW-IHT-1271(config)# no switchport vlan mapping 1 12
AW-IHT-1271(config)#
no tacacs-server host
no tacacs-server key
no tacacs-server timeout
Parameter
deadtime Time to stop using a TACACS+ server that doesn't respond
host Specify a TACACS+ server
Host name or IP address
key Set TACACS+ encryption key
timeout Time to wait for a TACACS+ server to reply
key Server specific key (overrides default)
port TCP port for TACACS+ server
timeout Time to wait for this TACACS+ server to reply (overrides default)
TCP port number
EXAMPLE
udld
Disable UDLD configurations on all fiber-optic ports.
SYNTAX
no udld [ aggressive | enable ]
Parameter
aggressive Disable UDLD aggressive mode on all fiber-optic interfaces.
AW-IHT-1271(config)# no tacacs-server deadtime
AW-IHT-1271(config)# no tacacs-server host 192.168.1.1 port 10000
AW-IHT-1271(config)# no tacacs-server key
AW-IHT-1271(config)# no tacacs-server timeout
AW-IHT-1271(config)#
enable Disable UDLD on all fiber-optic interfaces.
EXAMPLE
upnp
Set UPnP's configurations.
SYNTAX
no upnp
no upnp advertising-duration
no upnp ttl
Parameter
advertising-duration Set advertising duration
ttl Set TTL value
EXAMPLE
username
Establish User Name Authentication.
SYNTAX
no username
Parameter
User name allows letters, numbers and underscores
AW-IHT-1271(config)# no upnp advertising-duration
AW-IHT-1271(config)# no upnp ttl
AW-IHT-1271(config)#
AW-IHT-1271(config)# no udld enable
AW-IHT-1271(config)#
EXAMPLE
vlan
Vlan commands.
SYNTAX
no vlan protocol { { eth2 { <0x600-0xffff> | arp | ip | ipx | at } } | { snap { <0x0-0xffffff> | rfc_1042 | snap_8021h }
<0x0-0xffff> } | { llc <0x0-0xff> <0x0-0xff> } } group
no vlan { [ ethertype s-custom-port ] |
Parameter
protocol Protocol-based VLAN commands
eth2 Ethernet-based VLAN commands
<0x600-0xffff> Ether Type(Range: 0x600 - 0xFFFF)
arp Ether Type is ARP
ip Ether Type is IP
ipx Ether Type is IPX
at Ether Type is AppleTalk
snap SNAP-based VLAN group
<0x0-0xffffff> SNAP OUI (Range 0x000000 - 0XFFFFFF)
rfc_1042 SNAP OUI is rfc_1042
snap_8021h SNAP OUI is 8021h
<0x0-0xffff> PID (Range: 0x0 - 0xFFFF)
llc LLC-based VLAN group
<0x0-0xff> DSAP (Range: 0x00 - 0xFF)
<0x0-0xff> SSAP (Range: 0x00 - 0xFF)
AW-IHT-1271(config)# no username admin
AW-IHT-1271(config)#
group Protocol-based VLAN group commands
Group Name (Range: 1 - 16 characters)
Vlan list
ethertype
s-custom-port
EXAMPLE
voice
Voice appliance attributes.
SYNTAX
no voice vlan
no voice vlan aging-time
no voice vlan class
no voice vlan oui
no voice vlan vid
Parameter
vlan Vlan for voice traffic
aging-time Set secure learning aging time
class Set traffic class
oui OUI configuration
Traffice class value
vid Set VLAN ID
AW-IHT-1271(config)# no vlan 3
AW-IHT-1271(config)# no vlan ethertype s-custom-port
AW-IHT-1271(config)#
EXAMPLE
web
Web.
SYNTAX
no web privilege group [
Parameter
privilege Web privilege
group Web privilege group
Valid words are 'Aggregation' 'Debug' 'Dhcp_Client' Diagnostics
EEE GARP GVRP Green_Ethernet' 'IP2' 'IPMC_Snooping' 'LACP' 'LLDP'
'Loop_Protect' 'MAC_Table' 'MEP' 'MVR' 'Maintenance'
'Mirroring' 'NTP' 'POE' 'Ports' 'Private_VLANs' 'QoS'
'RPC' 'Security' 'Spanning_Tree' 'System' 'Timer'
'UPnP' 'VCL' 'VLANs' 'Voice_VLAN' XXRP
'sFlow'
level Web privilege group level
EXAMPLE
ntp
Configure NTP.
AW-IHT-1271(config)# no web privilege group LACP level
AW-IHT-1271(config)#
AW-IHT-1271(config)# no voice vlan vid
AW-IHT-1271(config)# no voice vlan class
AW-IHT-1271(config)# no voice vlan aging-time
AW-IHT-1271(config)#
SYNTAX
ntp
ntp server <1-5> ip-address
ntp server <1-5> ip-address
ntp server <1-5> ip-address
Parameter
server Configure NTP server
<1-5> index number
ip-address ip address
ipv4 address
ipv6 address
domain name
EXAMPLE
poe
Configure poe.
SYNTAX
poe management mode { class-consumption | class-reserved-power | allocation-consumption |
allocation-reserved-power | lldp-consumption | lldp-reserved-power }
poe ping-check { enable | disable }
poe select-all
Parameter
management Use management mode to configure PoE power management method.
select-all Configure PoE Schedule mode.
Ping-check Enable/Disable POE Ping Check.
Mode PoE Power Management Mode
allocation-consumption Max. port power determined by allocated, and power is managed according to power
AW-IHT-1271(config)# ntp server 3 ip-address 192.168.1.1
AW-IHT-1271(config)#
consumption.
allocation-reserved-power Max. port power determined by alocated, and power is managed according to
reserved power.
class-consumption Max. port power determined by class, and power is managed according to power
consumption.
class-reserved-power Max. port power determined by class, and power is managed according to reserved
power.
lldp-consumption Max. port power determined by LLDP Media protocol, and power is managed
according to power consumption.
lldp-reserved-power Max. port power determined by LLDP Media protocol, and power is managed
according to reserved power.
EXAMPLE
port-security
Enable/disable port security globally.
SYNTAX
port-security
port-security aging
port-security aging time
Parameter
aging Time in seconds between check for activity on learned MAC addresses.
time Time in seconds between check for activity on learned MAC addresses.
AW-IHT-1271(config)# poe management mode allocation-consumption
AW-IHT-1271(config)# poe management mode allocation-reserved-power
AW-IHT-1271(config)# poe management mode class-consumption
AW-IHT-1271(config)# poe management mode class-reserved-power
AW-IHT-1271(config)# poe management mode lldp-consumption
AW-IHT-1271(config)# poe management mode lldp-reserved-power
AW-IHT-1271(config)# Poe ping-check enable
AW-IHT-1271(config)# Poe select-all 3
AW-IHT-1271(config)#
<10-10000000> seconds
EXAMPLE
privilege
Command privilege parameters.
SYNTAX
privilege { exec | configure | config-vlan | line | interface | if-vlan | ipmc-profile | snmps-host | stp-aggr | dhcp-pool
| rfc2544-profile } level
Parameter
config-vlan VLAN Configuration Mode
configure Global configuration mode
dhcp-pool DHCP Pool Configuration Mode
exec Exec mode
if-vlan VLAN Interface Mode
interface Port List Interface Mode
ipmc-profile IPMC Profile Mode
line Line configuration mode
rfc2544-profile RFC2544 Profile Mode
snmps-host SNMP Server Host Mode
stp-aggr STP Aggregation Mode
level Set privilege level of command
Initial valid words and literals of the command to modify, in 128 char's
EXAMPLE
AW-IHT-1271(config)# port-security agin time 1000
AW-IHT-1271(config)#
ptp
Precision time Protocol (1588)
SYNTAX
ptp <0-3>clk sync <1-1000> ap <1-40>
ptp <0-3> domain <0-127>
ptp <0-3> filter { [ delay <0-6> ] | [ dist <1-10> ] | [ filter-type ( basic | ms-pdv ) ] | [ period <1-10000> ] }
ptp <0-3> ho [ adj-threshold <1-1000> ] | [ filter <10-86400> ]
ptp <0-3> log <1-4>
ptp <0-3> mode { bcfrontend| boundary | e2etransparent | master | p2ptransparent | slave } { [ clock-domain 0 ] |
[ dscp <0-63> ] | [ ethernet ] | [ ethernet-mixed ] | [ id
<1-100> ] | [ oam ] | [ onepps ] | [ onestep ] | [ oneway ] | [ profile ( g8265.1 | g9275.1 | ieee1588 ) ] | [ twostep ] |
[ twoway ] | [ vid
ptp <0-3> ( priority1 | priority2 ) <0-255> |
ptp <0-3> servo ( ad <1-10000> ) | ( ai <1-10000> ) | ( ap <1-1000> ) | displaystates | phase-mode
ptp <0-3> slave-cfg [ offset-fail | offset-ok | stable-offset ]
ptp <0-3> time-property [ freq-traceable | leap-59 | leap-61 | ptptimescale | time-source | time-traceable |
utc-offset | valid ]
ptp <0-3> uni <0-4> [
ptp ext { [ ext <1-25000000> ] | [ input ( ext | ltc-freq | ltc-phase | osc | sysnce-dpll | vcxo ) ] | [ ltc-freq ( ext | input
| out-in | output ) ] | [ ltc-phase ( ext | input | out-in | output ) ] | [ osc ( ext | input | out-in | output )] | [ out-in ( ext |
ltc-freq | ltc-phase | osc | sysnce-dpll | vcxo ) ] | output ( ext | ltc-freq | ltc-phase | osc | sysnce-dpll | vcxo ) ] |
[ synce-dpll ( ext | input | out-in | output )] | [ vcxo ( ext | input | out-in | output ) ] }
ptp system-time ( get | set )
ptp tc-internal [ mode <0-3> ]
AW-IHT-1271(config)# privilege config-vlan level 10 LINE
AW-IHT-1271(config)# privilege configure level 10 LINE
AW-IHT-1271(config)# privilege dhcp-pool level 10 LINE
AW-IHT-1271(config)#
Parameter
config-vlan VLAN Configuration Mode
configure Global configuration mode
<0-3> Clock instance [0-3]
ext Update the 1PPS and External clock output configuration and vcxo frequency rate
adjustment option
system-time Enable synchronization between PTP time and system time
tc-internal Define the internal mode used in TC's
clk Set PTP slave clock options
domain Clock domain for PTP
filter Set filter parameters
ho Set PTP Servo holdover parameters
log Set the PTP debug mode
mode Enable a PTP instance
priority1 Clock priority 1 for PTP BMC algorithm (0 is highest priority)
priority2 Clock priority 2 for PTP BMC algorithm (0 is highest priority)
servo Set Servo parameters
slave-cfg Set PTP clock Slave Configuration
time-property Set time properties
uni Set a Unicast Slave configuration entry
sync Set PTP slave clock options to 'clock is SyncE locked'
<1-1000> [1..1000] Threshold in ns for offsetFromMaster defines when the offset
increment/decrement mode is entered
ap Set the adjustment factor
<1-40> [1..40] The offset increment/decrement adjustment factor
<0-127> PTP domain: range = 0-127
delay Set delay filter parameter
dist Set offset filter dist parameter
filter-type Define offset filter type
period Set offset filter period parameter
<0-6> Log2 of timeconstant in delay lowpass filter, valid range: 1-6, Setting the value to 0
means use the same filter function as for the offset measurement, in this case the
delay filter uses the 'period' and 'dist' parameters.
<1-10> Distance between servo update n number of measurement periods,
valid range: 1-10
basic Basic offset filter
ms-pdv MS-PDV
<1-10000> Measurement period in number of sync events, valid range: 1-10000
adj-threshold Set adjustment threshold
filter Set stabilization period
<1-1000> [1..1000] max frequency adjustment change within the holdover stabilization period
(in units of 0.1 ppb)
filter Set stabilization period
<10-86400> [10..86400] Holdover filter and stabilization period
<1-4> 1-4 Debug log mode, 1 => log offset from master, 2 => log sync packets,
3 => log Delay_req, 4 => log both
bcfrontend Boundary Clock front end
boundary Ordinary / Boundary clock
e2etransparent End to end transparent clock
master Master only clock
p2ptransparent Peer to peer transparent clock
slave Slave only clock
clock-domain Define clock domain used by this instance. Instances with different clock domain can
have different time.
dscp Define DSCP field used in IPv4 enacpaulation
ethernet Ethernet protocol encapsulation
ethernet-mixed Ethernet protocol encapsulation using mix of unicast and multicast
id define PTP clock instance identifier
ip4mixed IPv4 mixed multicast/unicast protocol encapsulation
ip4multi IPv4 multicast protocol encapsulation
ip4unicast IPv4 unicast protocol encapsulation
mep Define MEP id used in OAM based PTP
oam OAM encapsulation (only used in Serval based Distributed TC)
onepps 1PPS master slave synchronization(only used with Gen2 1588 PHY's)
onestep One-step mode
oneway Oneway slave mode (no Delay_req)
profile Indication that clock has an associated profile
twostep Two-step mode
twoway Twoway slave mode
vid define VLAN ID
0 Clock domain used. The Clock domain may be HW based or SW based. Jaguar2
has 3 hw clock domains, other switches have 1 hw clock domain.
<0-63> DSCP field value used in IPv4 enacpaulation
PTP clock instance identifier (8 bytes)
<1-100> MEP instance number used if the OAM protocol option is used
g8265.1 G8265.1 profile
g8275.1 G8275.1 profile
ieee1588 IEEE 1588 profile
VLAN id
<0-255> PTP clock priority1: range = 0-255
| Output modifiers
ad Set 'D' parameter in the servo
ai Set 'I' parameter in the servo
ap Set 'P' parameter in the servo
displaystates Enable logging of servo parameters on the console
phase-mode Enable phase mode in the servo
<1-10000> [1..10000] 'D' component in PID servo regulator
<1-10000> [1..10000] 'I' component in PID servo regulator.
<1-1000> [1..1000] 'P' component in PID servo regulator
offset-fail set the offset-fail threshold
offset-ok set the offset-ok threshold
stable-offset set the stable-offset threshold
freq-traceable frequency is traceable
leap-59 leap59 in current day
leap-61 leap61 in current day
ptptimescale timing is a PTP time scale
time-source set timesource
time-traceable timing is traceable
utc-offset set utc offset
valid UTC offset is valid
<0-4> [0..4] Index in the slave table
IPv4 address of requested master clock
duration Set the Duration parameter
<10-1000> Duration [10..1000]. Number of seconds for which the Announce/Sync messages
are requested
ext Enable external clock frequency output
input Enable 1PPS input
ltc-freq Select Local Time Counter (LTC) frequency control
ltc-phase Select Local Time Counter (LTC) phase control (assumes tha the frequency is
locked by means of SyncE)
osc Select an oscillator independent of SyncE for frequency control, if supported by
the HW
out-in Enable 1PPS output and input (Jaguar1 only)
output Enable 1PPS output
synce-dpll Select SyncE DPLL frequency control, if allowed by SyncE
vcxo Enable VCXO frequency control (same as synce-dpll, kept here for
backwards compatibility)
<1-25000000> [1..25.000.000] External Clock output frequency in Hz
get Get (update) the PTP time from the system time
set Set (update) the system time from the PTP time
mode Set mode
<0-3> mode [0-3] (0 = MODE_30BIT, 1 = MODE_32BIT, 2 = MODE_44BIT,
3 =MODE_48BIT)
EXAMPLE
AW-IHT-1271(config)# ptp 1 clk sync 1 ap 1
AW-IHT-1271(config)#
AW-IHT-1271(config)# ptp 1 ho adj-threshold 1 filter 19
AW-IHT-1271(config)#
AW-IHT-1271(config)# ptp 1 log 2
AW-IHT-1271(config)#
qos
Table : configure qos Commands
Command Function
map Global QoS Map/Table
qce QoS Control Entry
storm Storm policer
map
Global QoS Map/Table.
SYNTAX
qos map cos-dscp <0~7> dpl
af31 | af32 | af33 | af41 | af42 | af43 | cs1 | cs2 | cs3 | cs4 | cs5 | cs6 | cs7 | ef | va } }
qos map dscp-classify {
af42 | af43 | cs1 | cs2 | cs3 | cs4 | cs5 | cs6 | cs7 | ef | va } }
qos map dscp-cos { < dscpNum : 0~63> | { be | af11 | af12 | af13 | af21 | af22 | af23 | af31 | af32 | af33 | af41 |
af42 | af43 | cs1 | cs2 | cs3 | cs4 | cs5 | cs6 | cs7 | ef | va } } cos
qos map dscp-egress-translation { < DscpNum : 0~63> | { be | af11 | af12 | af13 | af21 | af22 | af23 | af31 | af32 |
af33 | af41 | af42 | af43 | cs1 | cs2 | cs3 | cs4 | cs5 | cs6 | cs7 | ef | va } }
| af11 | af12 | af13 | af21 | af22 | af23 | af31 | af32 | af33 | af41 | af42 | af43 | cs1 | cs2 | cs3 | cs4 | cs5 | cs6 | cs7 |
ef | va } }
qos map dscp-ingress-translation { < DscpNum : 0~63> | { be | af11 | af12 | af13 | af21 | af22 | af23 | af31 | af32 |
af33 | af41 | af42 | af43 | cs1 | cs2 | cs3 | cs4 | cs5 | cs6 | cs7 | ef | va } } to { < DscpNum : 0-63> | { be | af11 | af12
| af13 | af21 | af22 | af23 | af31 | af32 | af33 | af41 | af42 | af43 | cs1 | cs2 | cs3 | cs4 | cs5 | cs6 | cs7 | ef | va } }
Parameter
cos-dscp Map for cos to dscp
dscp-classify Map for dscp classify enable
dscp-cos Map for dscp to cos
dscp-egress-translation Map for dscp egress translation
dscp-ingress-translation Map for dscp ingress translation
dpl Specify drop precedence level
Specific drop precedence level or range
dscp Specify DSCP
Specific DSCP
cos Specify class of QoS
Specific class of QoS
af11 Assured Forwarding PHB AF11(DSCP 10)
af12 Assured Forwarding PHB AF12(DSCP 12)
af13 Assured Forwarding PHB AF13(DSCP 14)
af21 Assured Forwarding PHB AF21(DSCP 18)
af22 Assured Forwarding PHB AF22(DSCP 20)
af23 Assured Forwarding PHB AF23(DSCP 22)
af31 Assured Forwarding PHB AF31(DSCP 26)
af32 Assured Forwarding PHB AF32(DSCP 28)
af33 Assured Forwarding PHB AF33(DSCP 30)
af41 Assured Forwarding PHB AF41(DSCP 34)
af42 Assured Forwarding PHB AF42(DSCP 36)
af43 Assured Forwarding PHB AF43(DSCP 38)
be Default PHB(DSCP 0) for best effort traffic
cs1 Class Selector PHB CS1 precedence 1(DSCP 8)
cs2 Class Selector PHB CS2 precedence 2(DSCP 16)
cs3 Class Selector PHB CS3 precedence 3(DSCP 24)
cs4 Class Selector PHB CS4 precedence 4(DSCP 32)
cs5 Class Selector PHB CS5 precedence 5(DSCP 40)
cs6 Class Selector PHB CS6 precedence 6(DSCP 48)
cs7 Class Selector PHB CS7 precedence 7(DSCP 56)
ef Expedited Forwarding PHB(DSCP 46)
va Voice Admit PHB(DSCP 44)
EXAMPLE
qce
QoS Control Entry.
SYNTAX
qos qce refresh
qos qce { [ update ] }
0-1> | any } ] [ smac {
[ frametype { any | { etype [ { <0x600-0x7ff,0x801-0x86dc,0x86de-0xffff> | any } ] } | { llc [ dsap { <0-0xff> | any } ]
[ ssap { <0-0xff> | any } ] [ control { <0-0xff> | any } ] } | { snap [ { <0-0xffff> | any } ] } | { ipv4 [ proto { <0-255> | tcp
| udp | any } ] [ sip {
af32 | af33 | af41 | af42 | af43 | cs1 | cs2 | cs3 | cs4 | cs5 | cs6 | cs7 | ef | va } | any } ] [ frag { yes | no | any } ]
[ sport { <0~65535> | any } ] [ dport { <0~65535> | any } ] } | { ipv6 [ proto { <0-255> | tcp | udp | any } ] [ sip
{
af42 | af43 | cs1 | cs2 | cs3 | cs4 | cs5 | cs6 | cs7 | ef | va } | any } ] [ sport { <0~65535> | any } ] [ dport
{ <0~65535> | any } ] } } ] [ action { [ cos { <0-7> | default } ] [ dpl { <0-1> | default } ] [ dscp { <0-63> | { be | af11 |
af12 | af13 | af21 | af22 | af23 | af31 | af32 | af33 | af41 | af42 | af43 | cs1 | cs2 | cs3 | cs4 | cs5 | cs6 | cs7 | ef | va }
| default } ] } ]
Parameter
QCE ID
refresh Refresh QCE tables in hardware
update Update an existing QCE
action Specify action
dei Specify DEI (Drop Eligible Indicator)
AW-IHT-1271(config)# qos map cos-dscp 5 dpl 1 dscp 20
AW-IHT-1271(config)#
dmac-type Specify DMAC type
frametype Specify frame type
ingress Ingress interfaces
last Place QCE at the end
next Place QCE before the next QCE ID
pcp Specify PCP (Priority Code Point)
smac Specify SMAC. If 'qos qce dmac-dip' is set, this parameter specifies the DMAC
tag Specify tag options
vid Specify VLAN ID
cos Specify class of service
dpl Specify drop precedence level
dscp Specify DSCP
cos Specify class of service
Specific class of service
default Keep default class of service
Specific drop precedence level
default Keep default drop precedence level
Specific DSCP
af11 Assured Forwarding PHB AF11(DSCP 10)
af12 Assured Forwarding PHB AF12(DSCP 12)
af13 Assured Forwarding PHB AF13(DSCP 14)
af21 Assured Forwarding PHB AF21(DSCP 18)
af22 Assured Forwarding PHB AF22(DSCP 20)
af23 Assured Forwarding PHB AF23(DSCP 22)
af31 Assured Forwarding PHB AF31(DSCP 26)
af32 Assured Forwarding PHB AF32(DSCP 28)
af33 Assured Forwarding PHB AF33(DSCP 30)
af41 Assured Forwarding PHB AF41(DSCP 34)
af42 Assured Forwarding PHB AF42(DSCP 36)
af43 Assured Forwarding PHB AF43(DSCP 38)
be Default PHB(DSCP 0) for best effort traffic
cs1 Class Selector PHB CS1 precedence 1(DSCP 8)
cs2 Class Selector PHB CS2 precedence 2(DSCP 16)
cs3 Class Selector PHB CS3 precedence 3(DSCP 24)
cs4 Class Selector PHB CS4 precedence 4(DSCP 32)
cs5 Class Selector PHB CS5 precedence 5(DSCP 40)
cs6 Class Selector PHB CS6 precedence 6(DSCP 48)
cs7 Class Selector PHB CS7 precedence 7(DSCP 56)
default Keep default DSCP
ef Expedited Forwarding PHB(DSCP 46)
va Voice Admit PHB(DSCP 44)
any Any
broadcast Broadcast
multicast Multicast
unicast Unicast
etype Ethernet frames
ipv4 IPv4 frames
ipv6 IPv6 frames
llc LLC frames
snap SNAP frames
Specific EtherType
interface Interfaces
The next QCE ID
Specific PCP (0-7) or range (0-1, 2-3, 4-5, 6-7, 0-3 or 4-7)
Specific SMAC (XX-XX-XX-XX-XX-XX)
tagged Tagged frames only
untagged Untagges frames only
Specific VLAN ID or range
interface Interfaces
Gigabitethernet 1 Gigabit Ethernet Port
Port list in 1/1-12 for Gigabitethernet
EXAMPLE
storm
Storm policer.
SYNTAX
qos storm { unicast | multicast | broadcast }
Parameter
broadcast Police broadcast frames
multicast Police multicast frames
unicast Police unicast frames
Policer rate (default fps)
kfps Rate is kfps
EXAMPLE
AW-IHT-1271(config)# qos storm broadcast 256 kfps
AW-IHT-1271(config)#
AW-IHT-1271(config)# qos qce 100 vid any
AW-IHT-1271(config)#
radius-server
Configure RADIUS.
SYNTAX
radius-server attribute 32
radius-server attribute 4
radius-server attribute 95
radius-server deadtime <1-1440>
radius-server host {
<0-65535> ] [ timeout <1-1000> ] [ retransmit <1-1000> ] [ key
radius-server key
radius-server retransmit <1-1000>
radius-server timeout <1-1000>
Parameter
Attribute
deadtime Time to stop using a RADIUS server that doesn't respond
host Specify a RADIUS server
key Set RADIUS encryption key
retransmit Specify the number of retries to active server
timeout Time to wait for a RADIUS server to reply
Time in minutes
IPv4 address
IPv6 address
Hostname
acct-port UDP port for RADIUS accounting server
auth-port UDP port for RADIUS authentication server
key Server specific key (overrides default)
retransmit Specify the number of retries to active server (overrides default)
timeout Time to wait for this RADIUS server to reply (overrides default)
UDP port number
Wait time in seconds
The shared key
<1-1000> Number of retries for a transaction
EXAMPLE
rapid-ring
Set Rapid Ring's configurations
SYNTAX
rapid-ring entry
port2 GigabitEthernet
Parameter
entry Set entry index
index
role Set role value
disabled role value disabled
master role value master
member role value member
rapid-chain role value rapid-chain
port1 Set port1
AW-IHT-1271(config)# radius-server host device key 12
AW-IHT-1271(config)#
GigabitEthernet 1 Gigabit Ethernet Port
Port ID in 1/1-12
port2 Set port2
EXAMPLE
ring-to-ring
Set Ring to Ring's configurations
SYNTAX
ring-to-ring role ( active | backup | disabled ) port GigabitEthernet
Parameter
role Set role value
active role value active
backup role value backup
disabled role value disabled
port Set port
GigabitEthernet 1 Gigabit Ethernet Port
Port ID in 1/1-12
EXAMPLE
rmon
AW-IHT-1271(config)# ring-to-ring role active port GigabitEthernet 1/3
AW-IHT-1271(config)#
AW-IHT-1271(config)# rapid-ring entry 0 role disabled port1 GigabitEthernet 1/1
port2 GigabitEthernet 1/1
AW-IHT-1271(config)#
Remote Monitoring.
SYNTAX
rmon alarm <1-65535>
<-2147483648-2147483647> [ <0-65535> ] falling-threshold <-2147483648-2147483647> [ <0-65535> ] { [ rising
| falling | both ] }
rmon alarm <1-65535> { ifInOctets | ifInUcastPkts | ifInNUcastPkts | ifInDiscards | ifInErrors | ifInUnknownProtos
| ifOutOctets | ifOutUcastPkts | ifOutNUcastPkts | ifOutDiscards | ifOutErrors }
| delta } rising-threshold <-2147483648-2147483647> [ <0-65535> ] falling-threshold
<-2147483648-2147483647> [ <0-65535> ] { [ rising | falling | both ] }
rmon event <1-65535> [ log ] [ trap
Parameter
alarm Configure an RMON alarm
event Configure an RMON event
<1-65535> Alarm entry ID
MIB object to monitor
<1-2147483647> Sample interval
absolute Test each sample directly
delta Test delta between samples
rising-threshold Configure the rising threshold
<-2147483648-2147483647> rising threshold value
<0-65535> Event to fire on rising threshold crossing
falling-threshold Configure the falling threshold
<-2147483648-2147483647> falling threshold value
rising Trigger alarm when the first value is larger than the rising threshold
falling Trigger alarm when the first value is less than the falling threshold
both Trigger alarm when the first value is larger than the rising threshold or less than the
falling threshold (default)
ifInOctets The total number of octets received on the interface, including framing characters
ifInUcastPkts The number of uni-cast packets delivered to a higher-layer protocol
ifInNUcastPkts The number of broad-cast and multi-cast packets delivered to a higher-layer protocol
ifInDiscards The number of inbound packets that are discarded even the packets are normal
ifInErrors The number of inbound packets that contained errors preventing them from being
deliverable to a higher-layer protocol
ifInUnknownProtos The number of the inbound packets that were discarded because of the unknown or
un-support protocol
ifOutOctets The number of octets transmitted out of the interface , including framing characters
ifOutUcastPkts The number of uni-cast packets that request to transmit
ifOutNUcastPkts The number of broad-cast and multi-cast packets that request to transmit
ifOutDiscards The number of outbound packets that are discarded event the packets is normal
ifOutErrors The The number of outbound packets that could not be transmitted because of errors
ifIndex
<1-2147483647> Sample interval
absolute Test each sample directly
delta Test delta between samples
rising-threshold Configure the rising threshold
EXAMPLE
sflow
Statistics flow
SYNTAX
sflow agent-ip { ipv4
AW-IHT-1271(config)# rmon alarm 10000 ifInErrors 10 9999 absolute rising-threshold
0 falling-threshold 0 both
AW-IHT-1271(config)#
sflow collector-address{
sflow collector-port <1-65535>
sflow max-datagram-size [ receiver
sflow timeout [ receiver
Parameter
agent-ip The agent IP address used as agent-address in UDP datagrams. Defaults to IPv4 loopback
address.
Ipv4 ipv4 address
Ipv6 ipv6 address
ipv6 address
ipv4 address
collector-address Collector address
collector-port Collector UDP port
<1-65535> Port Number
max-datagram-size Maximum datagram size.
<200-1468> Bytes
timeout Receiver timeout measured in seconds. The switch decrements the timeout once per
second, and as long as it is non-zero, the receiver receives samples. Once the timeout reaches 0, the receiver
and all its configuration is reset to defaults.
<0-2147483647> Number in seconds
EXAMPLE
AW-IHT-1271(config)# sflow agent-ip ipv4 192.168.1.2
AW-IHT-1271(config)# sflow collector-port 3
AW-IHT-1271(config)# sflow max-datagram-size 333
AW-IHT-1271(config)# sflow timeout 3333
AW-IHT-1271(config)#
smtp
Set email information
SYNTAX
smtp delete mailaddress <1-6>
smtp delete [ returnpath | sender | server | username ]
smtp mailaddress <1-6>
smtp ( returnpath | sender | server )
smtp username
Parameter
delete Delete command
mailaddress Configure email address
returnpath Configure email returnpath
sender Configure email sender
server Configure email server
username Configure email user name
mailaddress Delete email address
returnpath Delete returnpath
sender Delete sender
server Delete email server
username Delete username and password
<1-6> Email address index
Up to 47 characters describing mail address
Up to 47 characters describing returnpath
Up to 47 characters describing sender
Up to 47 characters describing email server
Up to 47 characters describing user name
Configure email password
EXAMPLE
AW-IHT-1271(config)# smtp delete mailaddress 1
AW-IHT-1271(config)# smtp delete returnpath
AW-IHT-1271(config)#
snmp-server
Set SNMP server's configurations
SYNTAX
snmp-server
Table : configure snmp-server Commands
Command Function
access access configuration
community Set the SNMP community
contact Set the SNMP server's contact string
engine-id Set SNMP engine ID
host Set SNMP host's configurations
location Set the SNMP server's location string
security-to-group security-to-group configuration
trap Set trap's configurations
user Set the SNMPv3 user's configurations
version Set the SNMP server's version
view MIB view configuration
access
access configuration.
SYNTAX
snmp-server access
Parameter
group name
model security model
any any security model
v1 v1 security model
v2c v2c security model
v3 v3 security model
level security level
auth authNoPriv Security Level
noauth noAuthNoPriv Security Level
priv authPriv Security Level
read specify a read view for the group
write specify a write view for the group
read view name
write view name
EXAMPLE
community
Set the SNMP community.
SYNTAX
snmp-server community v2c
snmp-server community v3
Parameter
v2c SNMPv2c
Community word
ro Read only
rw Read write
v3 SNMPv3
AW-IHT-1271(config)# snmp-server access text model v2c level noauth
write text
AW-IHT-1271(config)#
Community word
IPv4 address
IPv4 netmask
EXAMPLE
contact
Set the SNMP server's contact string.
SYNTAX
snmp-server contact
Parameter
contact Set the SNMP server's contact string
contact string
EXAMPLE
engine-id
Set SNMP engine ID.
SYNTAX
snmp-server engine-id local
Parameter
local Set SNMP local engine ID
local engine ID
EXAMPLE
AW-IHT-1271(config)# snmp-server contact text
AW-IHT-1271(config)#
AW-IHT-1271(config)# snmp-server community v2c text
AW-IHT-1271(config)#
host
Set SNMP host's configurations.
SYNTAX
snmp-server host
Parameter
Name of the host configuration
EXAMPLE
location
Set the SNMP server's location string.
SYNTAX
snmp-server location
Parameter
location string
EXAMPLE
security-to-group
security-to-group configuration.
AW-IHT-1271(config)# snmp-server location text
AW-IHT-1271(config)#
AW-IHT-1271(config)# snmp-server host text
AW-IHT-1271(config-snmps-host)#
AW-IHT-1271(config)# snmp-server engine-id local 1234567891
AW-IHT-1271(config)#
SYNTAX
snmp-server security-to-group model { v1 | v2c | v3 } name
word32>
Parameter
model security model
v1 v1 security model
v2c v2c security model
v3 v3 security model
name security user
security user name
group security group
security group name
EXAMPLE
trap
Set trap's configurations.
SYNTAX
snmp-server trap
EXAMPLE
user
Set the SNMPv3 user's configurations.
AW-IHT-1271(config)# snmp-server trap
AW-IHT-1271(config)#
AW-IHT-1271(config)# snmp-server security-to-group model v2c name text
group text
AW-IHT-1271(config)#
SYNTAX
snmp-server user
sha
Parameter
Username
engine-id engine ID
Engine ID octet string
md5 Set MD5 protocol
MD5 password
sha Set SHA protocol
SHA password
priv Set Privacy
des Set DES protocol
aes Set AES protocol
Set privacy password
EXAMPLE
version
Set the SNMP server's version.
SYNTAX
snmp-server version { v1 | v2c | v3 }
Parameter
v1 SNMPv1
AW-IHT-1271(config)# snmp-server user text engine-id 1234567891 md5
12345678 priv aes 12345678
AW-IHT-1271(config)#
v2c SNMPv2c
v3 SNMPv3
EXAMPLE
view
MIB view configuration.
SYNTAX
snmp-server view
Parameter
MIB view name
MIB view OID
include Ixcluded type from the view
exclude Excluded type from the view
EXAMPLE
spanning-tree
Spanning Tree protocol
Table : configure spanning-tree Commands
Command Function
aggregation Aggregation mode
edge Edge ports
mode STP protocol mode
mst STP bridge instance
AW-IHT-1271(config)# snmp-server view text .1 include
AW-IHT-1271(config)#
AW-IHT-1271(config)# snmp-server version v2c
AW-IHT-1271(config)#
recovery The error recovery timeout
transmit BPDUs to transmit
aggregation
Aggregation mode.
SYNTAX
spanning-tree aggregation
EXAMPLE
edge
Edge ports.
SYNTAX
spanning-tree edge bpdu-filter
spanning-tree edge bpdu-guard
Parameter
bpdu-filter Enable BPDU filter (stop BPDU tx/rx)
bpdu-guard Enable BPDU guard
EXAMPLE
mode
STP protocol mode.
SYNTAX
AW-IHT-1271(config)# spanning-tree edge bpdu-filter
AW-IHT-1271(config)#
AW-IHT-1271(config)# spanning-tree aggregation
AW-IHT-1271(config-stp-aggr)#
spanning-tree mode { stp | rstp | mstp }
Parameter
mstp Multiple Spanning Tree (802.1s)
rstp Rabid Spanning Tree (802.1w)
stp 802.1D Spanning Tree
EXAMPLE
mst
STP bridge instance.
SYNTAX
spanning-tree mst
spanning-tree mst < Instance : 0-7> vlan
spanning-tree mst forward-time
spanning-tree mst max-age
spanning-tree mst max-hops
spanning-tree mst name
Parameter
instance 0-7 (CIST=0, MST2=1...)
forward-time Delay between port states
max-age Max bridge age before timeout
max-hops MSTP bridge max hop count
name Name keyword
priority Priority of the instance
vlan VLAN keyword
AW-IHT-1271(config)# spanning-tree mode stp
AW-IHT-1271(config)#
Range in seconds
Range of VLANs
Range in seconds
Range in seconds
Hop count range
Name of the bridge
revision Revision keyword
<0-65535> Revision number
EXAMPLE
recovery
The error recovery timeouts.
SYNTAX
spanning-tree recovery interval
Parameter
interval The interval
Range in seconds
EXAMPLE
transmit
BPDUs to transmit.
SYNTAX
AW-IHT-1271(config)# spanning-tree recovery interval 50
AW-IHT-1271(config)#
AW-IHT-1271(config)# spanning-tree mst 7 vlan 10
AW-IHT-1271(config)#
spanning-tree transmit hold-count
Parameter
hold-count Max number of transmit BPDUs per sec
1-10 per sec, 6 is default
EXAMPLE
switchalert-management
switchAlert Management configuration
SYNTAX
switchalert-management delete <1-6>
switchalert-management get activity-code
switchalert-management link-option [automatic | ( manual <1-65535> ) ]
switchalert-management ( port-name | port-role ) interface [ GigabitEthernet
GigabitEthernet ) ] | [ * (
switchalert-management server
switchalert-management switchalert-management-mode [ disable | enable ]
Parameter
delete Delete Mobile in List
get Get Activity Code Action from SwitchAlert Management Server
link-option Configure NAT Option
port-name Interface specific description
port-role Configure Port Role
server Configure SwitchAlert Management server IP address
AW-IHT-1271(config)# spanning-tree transmit hold-count 5
AW-IHT-1271(config)#
switchalert-management-mode Configure SwitchAlert Management mode
<1-6> Mobile ID, available value is from 1 to 6
activity-code Get Activity Code Action from SwitchAlert Management Server
automatic Enable NAT Option as Automatic
manual Enable NAT Option as Manual
<1-65535> Port number
interface Select an interface to configure
* All switches or All ports
GigabitEthernet 1 Gigabit Ethernet Port
Up to 47 characters describing this interface
Port list for all port types
SwitchAlert Management IP address or host name
disable Disable SwitchAlert Management mode
enable Enable SwitchAlert Management mode
EXAMPLE
switchport
Set switching mode characteristics
SYNTAX
switchport vlan mapping <1-12>
Parameter
vlan vlan
AW-IHT-1271(config)# switchalert-management delete 1
AW-IHT-1271(config)# switchalert-management get activity-code
AW-IHT-1271(config-stp-aggr)#
mapping Add VLAN translation entry into a group.
<1-12> Group id
EXAMPLE
system
Set the SNMP server's configurations
SYNTAX
system contact
system location
system name
Parameter
contact Set the SNMP server's contact string
location Set the SNMP server's location string
name Set the SNMP server's system model name string
Maximum number of 255 character strings
EXAMPLE
tacacs-server
Configure TACACS+.
AW-IHT-1271(config)# system contact 222
AW-IHT-1271(config)# system location 333
AW-IHT-1271(config)# system name GE
AW-IHT-1271(config)#
AW-IHT-1271(config)# switchport vlan mapping 1 1 1
AW-IHT-1271(config)#
SYNTAX
tacacs-server deadtime
tacacs-server host
tacacs-server key
tacacs-server timeout
Parameter
deadtime Time to stop using a TACACS+ server that doesn't respond
host Specify a TACACS+ server
key Set TACACS+ encryption key
timeout Time to wait for a TACACS+ server to reply
Time in minutes
The shared key
Wait time in seconds
Hostname
IPv4 address
IPv6 address
port TCP port for TACACS+ server
<0-65535> TCP port number
EXAMPLE
tzidx
Configure timezone city/area
AW-IHT-1271(config)# tacacs-server deadtime 300
AW-IHT-1271(config)# tacacs-server host 192.168.1.2
AW-IHT-1271(config)# tacacs-server key 33
AW-IHT-1271(config)# tacacs-server timeout 300
AW-IHT-1271(config)#
SYNTAX
tzidx
Parameter
index of city/area
EXAMPLE
udld
Enable UDLD in the aggressive or normal mode and to set the configurable message timer on all fiber-optic ports.
SYNTAX
udld [ aggressive | enable | ( message time-interval <7-90> ) ]
Parameter
aggressive Enables UDLD in aggressive mode on all fiber-optic ports.
enable Enables UDLD in normal mode on all fiber-optic ports.
message Configures the period of time between UDLD probe messages on ports that
are in the advertisement phase and are determined to be bidirectional. The
range is from 7 to 90 seconds(currently default message time interval 7 sec
is supported).
time-interval Configures the period of time between UDLD probe messages on ports that
are in the advertisement phase and are determined to be bidirectional. The range
is from 7 to 90 seconds(currently default message time interval 7 sec is supported).
<7-90> Configures the period of time between UDLD probe messages on ports that are
in the advertisement phase and are determined to be bidirectional. The range is
AW-IHT-1271(config)# tzidx 5
AW-IHT-1271(config)#
from 7 to 90 seconds(currently default message time interval 7 sec is supported).
EXAMPLE
upnp
Set UPnP's configurations.
SYNTAX
upnp
upnp advertising-duration <100-86400>
upnp ttl <1-255>
Parameter
advertising-duration Set advertising duration
ttl Set TTL value
<100-86400> advertising duration
<1-255> TTL value
EXAMPLE
username
Establish User Name Authentication.
AW-IHT-1271(config)# upnp advertising-duration 8
AW-IHT-1271(config)# upnp ttl 25
AW-IHT-1271(config)#
AW-IHT-1271(config)# udld message time-interval 7
AW-IHT-1271(config)#
SYNTAX
username
username
username
Parameter
User name allows letters, numbers and underscores
privilege Set user privilege level
User privilege level
password Specify the password for the user
encrypted Specifies an ENCRYPTED password will follow
none NULL password
unencrypted Specifies an UNENCRYPTED password will follow
The UNENCRYPTED (Plain Text) user password. Any
printable characters including space is accepted.
Notice that you have no change to get the Plain Text
password after this command. The system will always
display the ENCRYPTED password.
The ENCRYPTED (hidden) user password. Notice the
ENCRYPTED password will be decoded by system
internally. You cannot directly use it as same as
the Plain Text and it is not human-readable text
normally.
EXAMPLE
vlan
AW-IHT-1271(config)# username jefferson privilege 15
password none
AW-IHT-1271(config)# (config)#
VLAN commands.
SYNTAX
vlan
vlan ethertype s-custom-port <0x0600-0xffff>
vlan protocol { { eth2 { <0x600-0xffff> | arp | ip | ipx | at } } | { snap { <0x0-0xffffff> | rfc_1042 | snap_8021h }
<0x0-0xffff> } | { llc <0x0-0xff> <0x0-0xff> } } group
Parameter
ISL VLAN IDs 1-4095
ethertype Ether type for Custom S-ports
protocol Protocol-based VLAN commands
s-custom-port Custom S-ports configuration
<0x0600-0xffff> Ether type (Range: 0x0600-0xffff>
eth2 Ethernet-based VLAN commands
<0x600-0xffff> Ether Type(Range: 0x600 - 0xFFFF)
arp Ether Type is ARP
ip Ether Type is IP
ipx Ether Type is IPX
at Ether Type is AppleTalk
snap SNAP-based VLAN group
<0x0-0xffffff> SNAP OUI (Range 0x000000 - 0XFFFFFF)
rfc_1042 SNAP OUI is rfc_1042
snap_8021h SNAP OUI is 8021h
<0x0-0xffff> PID (Range: 0x0 - 0xFFFF)
llc LLC-based VLAN group
<0x0-0xff> DSAP (Range: 0x00 - 0xFF)
<0x0-0xff> SSAP (Range: 0x00 - 0xFF)
group Protocol-based VLAN group commands
Group Name (Range: 1 - 16 characters)
EXAMPLE
voice
Voice appliance attributes.
SYNTAX
voice vlan
voice vlan aging-time
voice vlan class {
voice vlan oui
voice vlan vid
Parameter
advertising-duration Set advertising duration
vlan Vlan for voice traffic
aging-time Set secure learning aging time
<10-10000000> Aging time, 10-10000000 seconds
class Set traffic class
<0-7> Traffic class value
oui OUI configuration
OUI value
AW-IHT-1271(config)# vlan ethertype s-custom-port
0x1111
AW-IHT-1271(config)# vlan protocol eth2 arp group 123
AW-IHT-1271(config)#
description Set description for the OUI
Description line
vid Set VLAN ID
VLAN ID, 1-4095
EXAMPLE
web
Web.
SYNTAX
web privilege group
Parameter
privilege Web privilege
group Web privilege group
CWORD Valid words are 'Aggregation' 'Debug' 'Dhcp_Client'
'Green_Ethernet' 'IP2' 'IPMC_Snooping' 'LACP' 'LLDP'
'Loop_Protect' 'MAC_Table' 'MEP' 'MVR' 'Maintenance'
'Mirroring' 'NTP' 'POE' 'Ports' 'Private_VLANs' 'QoS'
'RPC' 'Security' 'Spanning_Tree' 'System' 'Timer'
'UPnP' 'VCL' 'VLAN_Translation' 'VLANs' 'Voice_VLAN'
'sFlow'
level Web privilege group level
cro Configuration Read-only level
AW-IHT-1271(config)# voice vlan aging-time 3333
AW-IHT-1271(config)# voice vlan class 7
AW-IHT-1271(config)# voice vlan vid 3333
AW-IHT-1271(config)#
crw Configuration Read-write level
sro Status/Statistics Read-only level
srw Status/Statistics Read-write level
EXAMPLE
AW-IHT-1271(config)# web privilege group ptp level sro
10
(config)#
4 COPY Commands of CLI
Copy from source to destination
SYNTAX
copy { startup-config | running-config | < flash:filename | tftp://server/path-and-filename > } { startup-config |
running-config | < flash:filename | tftp://server/path-and-filename > } [ syntax-check ][ | { begin | exclude |
include }{
Parameter
flash:filename | tftp://server/path-and-filename File in FLASH or on TFTP server
running-config Currently running configuration
startup-config Startup configuration
| Output modifiers
syntax-check Perform syntax check on source configuration
begin Begin with the line that matches
exclude Exclude lines that match
include Include lines that match
String to match output lines
EXAMPLE
AW-IHT-1271# copy startup-config running-config syntax-check |
include
#
5 DELETE Commands of CLI
Delete one file in flash: file system
SYNTAX
Delete
Parameter
Name of file to delete
EXAMPLE
AW-IHT-1271# delete text
AW-IHT-1271#
6 DIR Commands of CLI
Directory of all files in flash: file system
SYNTAX
Dir [ | begin | exclude | include
Parameter
| Output modifiers
begin Begin with the line that matches
exclude Exclude lines that match
include Include lines that match
String to match output lines
EXAMPLE
AW-IHT-1271# dir
Directory of flash:
r- 2011-01-01 00:00:00 720 default-config
rw 2011-01-01 00:00:11 1777 startup-config
2 files, 2497 bytes total.
7 DISABLE Commands of CLI
Turn off privileged commands
SYNTAX
disable <0-15>
Parameter
<0-15> Privilege level
EXAMPLE
AW-IHT-1271# disable 10
AW-IHT-1271#
8 DO Commands of CLI
To run exec commands in config mode
SYNTAX
Do
Parameter
LINE Exec Command
EXAMPLE
AW-IHT-1271# do show clock
System Time : 2011-01-01T00:03:44+00:00
9 DOT1X of CLI
IEEE Standard for port-based Network Access Control
SYNTAX
dot1x initialize [ interface (
Parameter
initialize Force re-authentication immediately
interface Interface
* All switches or All ports
Gigabitethernet 1 GigabitEthernet port
Port list in 1/1-12 for Gigabitethernet
EXAMPLE
AW-IHT-1271# dot1x initialize interface GigabitEthernet
1/1-12
AW-IHT-1271#
10 ENABLE of CLI
Turn on privileged commands
Syntax
Enable <1-15>
Parameter
<0-15> Choose privileged level
EXAMPLE
AW-IHT-1271# enable 10
AW-IHT-1271#
11 ERPS of CLI
Ethernet Ring Protection Switching
Syntax
erps 1-64 command [ clear | force | manual ] [ port0 | port1 ]
Parameter
1-64 ERPS group number
command Administrative Command
clear Clear command
force Force command
manual Manual command
port0 ERPS Port 0 interface
port1 ERPS Port 1 interface
EXAMPLE
AW-IHT-1271# erps 7 command manual port1
AW-IHT-1271#
12 FIRMWARE of CLI
Firmware upgrade/swap
Syntax
firmware swap
firmware upgrade <TFTPServer_path_file : word>
Parameter
swap Swap between Active and Alternate firmware image.
upgrade Firmware upgrade
TFTP Server IP address, path and file name
for the server containing the new image.
EXAMPLE
AW-IHT-1271# firmware upgrade tftp://192.168.1.1/path/GEL2706
Programming image...
AW-IHT-1271#
13 IP of CLI
IPv4 commands
Syntax
ip dhcp retry interface vlan
Parameter
dhcp Dhcp commands
retry Restart the DHCP query process
interface Interface
vlan Vlan interface
Vlan ID
EXAMPLE
AW-IHT-1271# ip dhcp retry interface vlan 1
% Failed to restart DHCP client on VLAN = 1.
14 IPV6 of CLI
IPv6 configuration commands
Syntax
Ipv6 dhcp-client restart
Ipv6 dhcp-client restart interface vlan
Parameter
dhcp-client Manage DHCPv6 client serviceretry
restart Restart DHCPv6 client servicevlan
interface Select an interface to configure
vlan VLAN of IPv6 interface
IPv6 interface VLAN list
EXAMPLE
AW-IHT-1271# ipv6 dhcp-client restart
AW-IHT-1271#
15 LINK-OAM of CL I
Link OAM configuration
Syntax
link-oam remote-loopback [ start | stop ] interface [ * | GigabitEthernet ]
Parameter
remote-loopback Configure remote loopback on interface
start Start remote loopback test on interface
stop Stop remote loopback test on interface
interface Start/Stop remote loopback test on a specific interface or interfaces.
* All switches or All ports
GigabitEthernet 1 Gigabit Ethernet Port
Port list for all port types
Port list in 1/1-12
EXAMPLE
16 NO of CLI
Negate a command or set its defaults
Syntax
no debug prompt
AW-IHT-1271# link-oam remote-loopback start interface *
AW-IHT-1271#
Parameter
debug Debugging functions
prompt Clear prompt for testing
EXAMPLE
AW-IHT-1271# no debug prompt
AW-IHT-1271#
17 PING of CLI
Send ICMP echo messages
Syntax
ping ip
ping ipv6
vlan
Parameter
ip IP (ICMP) echo
ICMP destination address
repeat Specify repeat count
1-60; Default is 5
size Specify datagram size
2-1452; Default is 56 (excluding MAC, IP and ICMP headers)
interval Specify repeat interval
0-30; Default is 0
ipv6 IPv6 (ICMPv6) echo
ICMPv6 destination address
repeat Specify repeat count
<1-60> 1-60; Default is 5
size Specify datagram size
<2-1452> 2-1452; Default is 56 (excluding MAC, IP and ICMP headers)
interval Specify repeat interval
<0-30> 0-30; Default is 0
interface Select an interface to configure
vlan VLAN Interface
VLAN identifier(s): VID
EXAMPLE
AW-IHT-1271# ping ip 33 interval 22 repeat 33 size 444
PING server 0.0.0.33, 444 bytes of dataitialize interfac
18 PLATFORM of CLI
Platform configuration
Syntax
platform debug [ allow | deny ]
Parameter
debug Debug command setting
allow Allow debug commands
deny Deny debug commands
EXAMPLE
AW-IHT-1271# platform debug allow
AW-IHT-1271#
AW-IHT-1271# platform debug deny
AW-IHT-1271#
19 PTP of CLI
Misc non persistent 1588 settings
Syntax
ptp <0-3> local-clock ratio <-10000000-10000000>
ptp <0-3> local-clock update
ptp <0-3> wireless delay <0-1000000000> <0-1000000> interface
ptp <0-3> wireless delay <0-1000000000> interface *
ptp <0-3> wireless delay <0-1000000000> interface ( * | GigabitEthernet )
ptp <0-3> wireless ( mode | pre-notification) interface *
ptp <0-3> wireless ( mode | pre-notification) interface ( * | GigabitEthernet )
Parameter
<0-3> PTP Clock instance [0-3]
local-clock Update local clock current time, or set clock ratio
wireless Enable wireless mode for one or more interfaces.
ratio Set the local master clock frequency ratio.
update The local clock is synchronized to the system clock
<-10000000-10000000> Ratio in units of 0,1 PPB, (ratio > 0 => faster clock, ratio < 0 => slower clock).
delay
mode Enable wireless mode for an interface.
pre-notification Issue a pre notification that the wireless modem is going to change.
<0-1000000000> Base wireless transmission delay (in pico seconds)
<0-1000000> Incremental wireless transmission delay pr. byte (in pico seconds)
interface Interface parameter
* All switches or All ports
GigabitEthernet 1 Gigabit Ethernet Port
Port list for all port types
Port list in 1/1-12
interface Interface
EXAMPLE
AW-IHT-1271# ptp 0 wireless pre-notification interface *
Wireless mode not available for ptp instance 0, port 1
Wireless mode not available for ptp instance 0, port 2
Wireless mode not available for ptp instance 0, port 3
Wireless mode not available for ptp instance 0, port 4
Wireless mode not available for ptp instance 0, port 5
Wireless mode not available for ptp instance 0, port 6
Wireless mode not available for ptp instance 0, port 7
Wireless mode not available for ptp instance 0, port 8
Wireless mode not available for ptp instance 0, port 9
Wireless mode not available for ptp instance 0, port 10
Wireless mode not available for ptp instance 0, port 11
Wireless mode not available for ptp instance 0, port 12
AW-IHT-1271#
20 RELOAD of CLI
Reload system.
Syntax
reload { { { cold | warm } [ sid
Parameter
cold Reload cold, i.e. reboot.
defaults Reload defaults without rebooting.
keep-ip Attepmt to keep VLAN1 IP setup.r
EXAMPLE
AW-IHT-1271# reload defaults
% Reloading defaults. Please stand by.
AW-IHT-1271# reload cold
% Cold reload in progress, please stand by.
AW-IHT-1271# +M25PXX : Init device with JEDEC ID 0x20BA19.
Luton26 board detected (VSC7427 Rev. D).
RedBoot(tm) bootstrap and debug environment [ROMRAM]
Non-certified release, version 1_15a-Vitesse - built 18:36:46, Sep 30 2016
Copyright (C) 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009
Free Software Foundation, Inc.
RedBoot is free software, covered by the eCos license, derived from the
GNU General Public License. You are welcome to change it and/or distribute
copies of it under certain conditions. Under the license terms, RedBoot's
source code and full license terms must have been made available to you.
Redboot comes with ABSOLUTELY NO WARRANTY.
Platform: VCore-III (MIPS32 24KEc) LUTON26
RAM: 0x80000000-0x88000000 [0x80021f70-0x87fe1000 available]
FLASH: 0x40000000-0x41ffffff, 512 x 0x10000 blocks
== Executing boot script in 1.000 seconds - enter ^C to abort
RedBoot> fis load -d managed
Image loaded from 0x80040000-0x80bf3d80
RedBoot> go
21 Send of CLI
Send a message to other tty lines
Syntax
send { * |
Parameter
* All tty lines
<0~16> Send a message to multiple lines
console Primary terminal line
0 Send a message to a specific line
vty Virtual terminal
<0~15> Send a message to multiple lines
Message to be sent to lines, in 128 char's
EXAMPLE
AW-IHT-1271# send * yes,i do
Enter TEXT message. End with the character 'y'.
y
-----------------------------------------
*** Message from line 0:
yes,i do
-----------------------------------------
AW-IHT-1271#
22 SHOW of CLI
Show running system information
Table : SHOW Commands
Command Function
aaa Login methods
access Access management
access-list Access list
aggregation Aggregation port configuration
clock Configure time-of-day clock
dot1x IEEE Standard for port-based Network Access Control
eps Ethernet Protection Switching
erps Ethernet Ring Protection Switching
evc Ethernet Virtual Connections
event Show trap event configuration
green-ethernet Green ethernet (Power reduction)
history Display the session command history
interface Interface status and configuration
ip Internet Protocol
ipmc IPv4/IPv6 multicast configuration
ipv6 IPv6 configuration commands
lacp LACP configuration/status
line TTY line information
link-oam Link OAM configuration
lldp Display LLDP neighbors information.
logging Syslog
loop-protect Loop protection configuration
mac Mac Address Table information
mep Maintenance Entity Point
monitor Monitoring different system events
mvr Multicast VLAN Registration configuration
ntp Configure NTP
platform platform specific information
poe Power over ethernet
port-security
privilege Display command privilege
process process
ptp Precision time Protocol (1588)
pvlan PVLAN status
qos Quality of Service
radius-server RADIUS configuration
rapid-ring Display Rapid Ring configurations
rmon RMON statistics
running-config Show running system information
sflow Statistics flow.
smtp Show email information
snmp Display SNMP configurations
spanning-tree STP Bridge
switchalert-management Show SwitchAlert Management information
switchport Display switching mode characteristics
System show system information
tacacs-server TACACS+ configuration
terminal Display terminal configuration parameters
udld Unidirectional Link Detection(UDLD) configurations,
statistics and status
upnp Display UPnP configurations
user-privilege Users privilege configuration
users Display information about terminal lines
version System hardware and software status
vlan VLAN status
voice Voice appliance attributes
web Web
aaa
Login methods.
SYNTAX
show aaa [ | {begin | exclude | include }
Parameter
| Output modifiers
begin Begin with the line that matches
exclude Exclude lines that match
include Include lines that match
String to match output lines
EXAMPLE
access
Access management.
SYNTAX
show access management [ statistics |
Parameter
management Access management configuration
statistics Statistics data
ID of access management entry
AW-IHT-1271# show aaa
console : local
telnet : local
ssh : local
http : local
AW-IHT-1271#
| Output modifiers
begin Begin with the line that matches
exclude Exclude lines that match
include Include lines that match
String to match output lines
EXAMPLE
access-list
Access list
SYNTAX
AW-IHT-1271# show access management
Switch access management mode is disabled
W: WEB/HTTPS
S: SNMP
T: TELNET/SSH
Idx VID Start IP Address End IP Address W S T
--- --- ------------------------------- ------------------------------
- - -
AW-IHT-1271# show access management statistics
Access Management Statistics:
-----------------------------
HTTP Receive: 0 Allow: 0 Discard: 0
HTTPS Receive: 0 Allow: 0 Discard: 0
SNMP Receive: 0 Allow: 0 Discard: 0
TELNET Receive: 0 Allow: 0 Discard: 0
SSH Receive: 0 Allow: 0 Discard: 0
AW-IHT-1271#
show access-list [ interface [ * | Gigabitetherne
statistics [
show access-list ace-status [ static ] [ loop-protect ] [ dhcp ] [ upnp ] [ arp-inspection ] [ mep ] [ ipmc ]
[ ip-source-guard ] [ ip-mgmt ] [ conflicts ]
Parameter
interface Select an interface to configure
* All Switches or All Ports
Gigbitethernet 1 Gigabit Ethernet Port
Port list in 1/1-12
rate-limiter Rate limiter
< RateLimiterList : 1~16> Rate limiter ID
ace Access list entry
statistics Traffic statistics
ACE ID
ace-status The local ACEs status
static The ACEs that are configured by users manually
loop-protect The ACEs that are configured by Loop Protect module
dhcp The ACEs that are configured by DHCP module
upnp The ACEs that are configured by UPnP module
arp-inspection The ACEs that are configured by ARP Inspection module
mep The ACEs that are configured by MEP module
ipmc The ACEs that are configured by IPMC module
ip-source-guard The ACEs that are configured by IP Source Guard module
ip-mgmt The ACEs that are configured by IP Mamagement module
conflicts The conflicts ACEs that does not applied to the hardware due to hardware limitations
| Output modifiers
begin Begin with the line that matches
exclude Exclude lines that match
include Include lines that match
String to match output lines
EXAMPLE
aggregation
Aggregation port configuration.
SYNTAX
AW-IHT-1271# show access-list ace statistics rate-limiter
Switch access-list ace number: 0
Switch access-list rate limiter ID 1 is 1 pps
Switch access-list rate limiter ID 2 is 1 pps
Switch access-list rate limiter ID 3 is 1 pps
Switch access-list rate limiter ID 4 is 1 pps
Switch access-list rate limiter ID 5 is 1 pps
Switch access-list rate limiter ID 6 is 1 pps
Switch access-list rate limiter ID 7 is 1 pps
Switch access-list rate limiter ID 8 is 1 pps
Switch access-list rate limiter ID 9 is 1 pps
Switch access-list rate limiter ID 10 is 1 pps
Switch access-list rate limiter ID 11 is 1 pps
Switch access-list rate limiter ID 12 is 1 pps
Switch access-list rate limiter ID 13 is 1 pps
Switch access-list rate limiter ID 14 is 1 pps
Switch access-list rate limiter ID 15 is 1 pps
Switch access-list rate limiter ID 16 is 1 pps
AW-IHT-1271#
show aggregation [ mode ][ | {begin | exclude | include }
Parameter
mode Traffic distribution mode
| Output modifiers
begin Begin with the line that matches
exclude Exclude lines that match
include Include lines that match
String to match output lines
EXAMPLE
clock
Configure time-of-day clock.
SYNTAX
show clock[detail]
Parameter
detail Display detailed information
EXAMPLE
AW-IHT-1271# show aggregation Mode
Aggregation Mode:
SMAC : Enabled
DMAC : Disabled
IP : Enabled
Port : Enabled
AW-IHT-1271#
dot1x
IEEE Standard for port-based Network Access Control.
SYNTAX
show dot1x statistics { eapol | radius | all } [ interface
show dot1x status [ interface (
AW-IHT-1271# show clock detail
System Time : 2011-01-01T00:53:57+00:00
Timezone : Timezone Offset : 0 ( 0 minutes)
Timezone Acronym :
Daylight Saving Time Mode : Disabled.
Daylight Saving Time Start Time Settings :
Week: 0
Day: 0
Month: 0
Date: 0
Year: 0
Hour: 0
Minute: 0
Daylight Saving Time End Time Settings :
Week: 0
Day: 0
Month: 0
Date: 0
Year: 0
Hour: 0
Minute: 0
Daylight Saving Time Offset : 1 (minutes)
Parameter
statistics Shows statistics for either eapol or radius.
all Show all dot1x statistics
eapol Show EAPOL statistics
radius Show Backend Server statistics
GigabitEthernet
Port list in 1/1-12 for Gigabotethernet
Status Shows dot1x status, such as admin state, port state and last
source.
brief Show status in a brief format
interface Interface
* All Switches or All Ports
Gigbitethernet 1 Gigabit Ethernet Port
Port list in 1/1-12 for Gigabitethernet
EXAMPLE
AW-IHT-1271# show dot1x statistics radius
Rx Access Rx Other Rx Auth. Rx Auth. Tx MAC
Interface Challenges Requests Successes Failures Responses Address
--------------------- ---------- ---------- ---------- ---------- ---------- --
GigabitEthernet 1/1 0 0 0 0 0 -
GigabitEthernet 1/2 0 0 0 0 0 -
GigabitEthernet 1/3 0 0 0 0 0 -
GigabitEthernet 1/4 0 0 0 0 0 -
GigabitEthernet 1/5 0 0 0 0 0 -
AW-IHT-1271#
eps
Ethernet Protection Switching
SYNTAX
show eps [ | ( begin | exclude | include )
Parameter
| Output modifiers
The range of EPS instances.
detail Show detailed state including configuration information.
begin Begin with the line that matches
exclude Exclude lines that match
include Include lines that match
String to match output lines
EXAMPLE
AW-IHT-1271# show eps detail ?
| Output modifiers
AW-IHT-1271# show eps detail
EPS state is:
Inst State Wstate Pstate TxAps r b RxAps r b FopPm FopCm
FopNr FopNoAps
EPS Configuration is:
Inst Dom Archi Wflow Pflow Wmep Pmep APSmep Direct
Revert Wtr Hold Aps
EPS Command is:
Inst Command
AW-IHT-1271#
erps
Ethernet Ring Protection Switching
SYNTAX
show erps 1-64 command ( clear | force | manual ) ( port0 | port1 )
Parameter
1-64 ERPS group number
command Administrative Command
clear Clear command
force Force command
manual Manual command
port0 ERPS Port 0 interface
port1 ERPS Port 1 interface
EXAMPLE
evc
Ethernet Protection Switching
SYNTAX
show evc { [ | ( begin | exclude | include )
( begin | exclude | include )
<1-256> ) ) ] | ece ( | | <1-256> ) | statistics }
AW-IHT-1271# erps 1 command clear port1
AW-IHT-1271#
Parameter
| Output modifiers
<1-256> EVC identifier
all Process all EVCs
ece EVC Control Entry
statistics Statistic counters
begin Begin with the line that matches
exclude Exclude lines that match
include Include lines that match
EXAMPLE
event
Show trap event configuration
SYNTAX
show event [ port ]
Parameter
port Show event port configuration
EXAMPLE
AW-IHT-1271# show evc 1
AW-IHT-1271#
green-ethernet
Green ethernet (Power reduction).
AW-IHT-1271# show event port
Port Active LinkOn LinkOff Overload RxThreshold TrafficDuration Syslog Trap SMTP
Switch2go DigitalOut Severity
---- ------- ------- ------- -------- ----------- --------------- ------- -------
------- --------- ---------- --------
1 enable enable enable disable 0 1 enable disable disable
disable disable Warning
2 enable enable enable disable 0 1 enable disable disable
disable disable Warning
3 enable enable enable disable 0 1 enable disable disable
disable disable Warning
4 enable enable enable disable 0 1 enable disable disable
disable disable Warning
5 enable enable enable disable 0 1 enable disable disable
disable disable Warning
6 enable enable enable disable 0 1 enable disable disable
disable disable Warning
7 enable enable enable disable 0 1 enable disable disable
disable disable Warning
8 enable enable enable disable 0 1 enable disable disable
disable disable Warning
9 enable enable enable disable 0 1 enable disable disable
disable disable Warning
10 enable enable enable disable 0 1 enable disable disable
disable disable Warning
11 enable enable enable disable 0 1 enable disable disable
disable disable Warning
12 enable enable enable disable 0 1 enable disable disable
disable disable Warning
AW-IHT-1271#
SYNTAX
show green-ethernet [ interface
show green-ethernet eee [ interface
show green-ethernet energy-detect [ interface
show green-ethernet short-reach [ interface
Parameter
eee Shows green ethernet EEE status for a specific port or ports.
energy-detect Shows green ethernet energy-detect status for a specific port or ports.
interface Shows green ethernet status for a specific port or ports.
short-reach Shows green ethernet short-reach status for a specific
interface
* All Switches or All ports
GigabitEthernet or
Port list in 1/1-12 for Gigabitethernet
EXAMPLE
AW-IHT-1271# show green-ethernet eee
Interface Lnk EEE Capable EEE Enabled LP EEE Capable In
Power Save
---------------------- --- ----------- ----------- ---------------
-------------
GigabitEthernet 1/1 No Yes No No No
GigabitEthernet 1/2 No Yes No No No
GigabitEthernet 1/3 No Yes No No No
GigabitEthernet 1/4 No Yes No No No
GigabitEthernet 1/5 No Yes No No No
GigabitEthernet 1/6 No Yes No No No
GigabitEthernet 1/7 No Yes No No No
GigabitEthernet 1/8 No Yes No No No
GigabitEthernet 1/9 No Yes No No No
history
Display the session command history.
SYNTAX
show history [ | {begin | exclude | include }
Parameter
| Output modifiers
begin Begin with the line that matches
exclude Exclude lines that match
include Include lines that match
String to match output lines
EXAMPLE
interface
Interface status and configuration.
SYNTAX
show interface
AW-IHT-1271# show history
show evc statistics
show green-ethernet EEE
show green-ethernet EEE interface GigabitEthernet
show history
AW-IHT-1271#
show interface
show interface
[ <0~7> ] } } ] [ { up | down } ]
show interface
show interface
show interface vlan [
Parameter
Gigabitethernet
* All Switches or All ports
Gigabitethernet 1 Gigabitethernet Port
Port list in 1/1-12 for Gigabitethernet
capabilities Display capabilities.
statistics Display statistics counters.
status Display status.
switchport Show interface switchport information
veriphy Run cable diagnostics and show result.
bytes Show byte statistics.
discards Show discard statistics.
down Show ports which are down
errors Show error statistics.
filtered Show filtered statistics.
packets Show packet statistics.
priority Queue number
up Show ports which are up
vlan VLAN status
VLAN list
EXAMPLE
ip
Internet Protocol.
SYNTAX
show ip arp
show ip arp inspection [ interface {
show ip arp inspection entry [ dhcp-snooping | static ] [ interface
show ip dhcp relay [ statistics ]
show ip dhcp snooping [ statistics ] [ interface
AW-IHT-1271# show interface GigabitEthernet 1/1-3 capabilities
GigabitEthernet 1/1 Capabilities:
SFP Type: None
SFP Vendor name:
SFP Vendor PN:
SFP Vendor revision:
GigabitEthernet 1/2 Capabilities:
SFP Type: None
SFP Vendor name:
SFP Vendor PN:
SFP Vendor revision:
GigabitEthernet 1/3 Capabilities:
SFP Type: None
SFP Vendor name:
SFP Vendor PN:
SFP Vendor revision:
AW-IHT-1271#
show ip http server secure status
show ip igmp snooping [ vlan
[ sfm-information ] ] [ detail ]
show ip igmp snooping mrouter [ detail ]
show ip interface brief
show ip name-server
show ip route
show ip source binding [ dhcp-snooping | static ] [ interface
show ip ssh
show ip statistics [ system ] [ interface vlan
show ip verify source [ interface
Parameter
arp Address Resolution Protocol
inspection ARP inspection
interface arp inspection entry interface config
Gigabitethernet
Port list in 1/1-12 for Gigabitethernet
vlan VLAN configuration
Select a VLAN id to configure
entry arp inspection entries
dhcp-snooping learn from dhcp snooping
static setting from static entries
dhcp Dynamic Host Configuration Protocol
relay DHCP relay agent configuration
statistics Traffic statistics
snooping DHCP snooping
http Hypertext Transfer Protocol
server HTTP web server
secure Secure
status Status
igmp Internet Group Management Protocol
snooping Snooping IGMP
vlan Search by VLAN
VLAN identifier(s): VID
group-database Multicast group database from IGMP
sfm-information Including source filter multicast information from IGMP
detail Detail running information/statistics of IGMP snooping
mrouter Multicast router port status in IGMP
detail Detail running information/statistics of IGMP snooping
interface IP interface status and configuration
brief Brief IP interface status
name-server Domain Name System
route Display the current ip routing table
binding ip source binding
dhcp-snooping learn from dhcp snooping
ssh Secure Shell
system IPv4 system traffic
icmp IPv4 ICMP traffic
icmp-msg IPv4 ICMP traffic for designated message type
<0~255> ICMP message type ranges from 0 to 255
verify verify command
source verify source
EXAMPLE
ipmc
IPv4/IPv6 multicast configuration.
SYNTAX
show ipmc profile [
show ipmc range [
Parameter
profile IPMC profile configuration
range A range of IPv4/IPv6 multicast addresses for the profile
Profile name in 16 char's
detail Detail information of a profile
AW-IHT-1271# show ip statistics system
IPv4 statistics:
Rcvd: 411 total in 36226 bytes
273 local destination, 0 forwarding
0 header error, 0 address error, 0 unknown protocol
0 no route, 0 truncated, 138 discarded
Sent: 0 total in 0 byte
0 generated, 0 forwarded
0 no route, 0 discarded
Frags: 0 reassemble (0 reassembled, 0 couldn't reassemble)
0 fragment (0 fragmented, 0 couldn't fragment)
0 fragment created
Mcast: 411 received in 36226 bytes
0 sent in 0 byte
Bcast: 273 received, 0 sent
AW-IHT-1271#
| Output modifiers
begin Begin with the line that matches
exclude Exclude lines that match
include Include lines that match
String to match output lines
EXAMPLE
ipv6
IPv6 configuration commands.
SYNTAX
show ipv6 interface [ vlan
show ipv6 mld snooping [ vlan
[ sfm-information ] ] [ detail ]
show ipv6 mld snooping mrouter [ detail ]
show ipv6 neighbor [ interface vlan
show ipv6 route [ interface vlan
show ipv6 statistics [ system ] [ interface vlan
Parameter
interface Select an interface to configure
vlan VLAN of IPv6 interface
IPv6 interface VLAN list
brief Brief summary of IPv6 status and configuration
statistics Traffic statistics
AW-IHT-1271# show ipmc range
AW-IHT-1271#
mld Multicasat Listener Discovery
snooping Snooping MLD
vlan Search by VLAN
VLAN identifier(s): VID
group-database Multicast group database from MLD
interface Search by port
Gigabitethernet
* All Switches or All ports
Gigabitethernet 1 Gigabit Ethernet Port
Port list in 1/1-12 for Gigabitethernet
sfm-information Including source filter multicast information from MLD
detail Detail running information/statistics of MLD snooping
mrouter Multicast router port status in MLD
neighbor IPv6 neighbors
route IPv6 routes
statistics Traffic statistics
system IPv6 system traffic
icmp IPv6 ICMP traffic
icmp-msg IPv6 ICMP traffic for designated message type
ICMP message type ranges from 0 to 255
| Output modifiers
begin Begin with the line that matches
exclude Exclude lines that match
include Include lines that match
String to match output lines
EXAMPLE
lacp
LACP configuration/status.
SYNTAX
show lacp { internal | statistics | system-id | neighbour } [ | {begin | exclude | include }
Parameter
internal Internal LACP configuration
neighbour Neighbour LACP status
statistics Internal LACP statistics
system-id LACP system id
| Output modifiers
begin Begin with the line that matches
AW-IHT-1271# show ipv6 statistics system
IPv6 statistics:
Rcvd: 2 total in 112 bytes
0 local destination, 0 forwarding
0 header error, 0 address error, 0 unknown protocol
0 no route, 0 truncated, 2 discarded
Sent: 8 total in 512 bytes
14 generated, 0 forwarded
3 no route, 0 discarded
Frags: 0 reassemble (0 reassembled, 0 couldn't reassemble)
0 fragment (0 fragmented, 0 couldn't fragment)
0 fragment created
Mcast: 2 received in 112 bytes
8 sent in 512 bytes
Bcast: 0 received, 0 sent
AW-IHT-1271#
exclude Exclude lines that match
include Include lines that match
String to match output lines
EXAMPLE
line
TTY line information.
SYNTAX
show line [ alive ] [ | {begin | exclude | include }
Parameter
alive Display information about alive lines
begin Begin with the line that matches
exclude Exclude lines that match
include Include lines that match
String to match output lines
EXAMPLE
AW-IHT-1271# show lacp internal
Port Mode Key Role Timeout Priority
---- -------- ---- ------ ------- --------
1 Disabled Auto Active Fast 32768
2 Disabled Auto Active Fast 32768
3 Disabled Auto Active Fast 32768
4 Disabled Auto Active Fast 32768
5 Disabled Auto Active Fast 32768
6 Disabled Auto Active Fast 32768
7 Disabled Auto Active Fast 32768
AW-IHT-1271#
Link-oam
Link OAM configuration
SYNTAX
show link-oam [ | | ( begin | exclude | include ) ]
show link-oam interface * [ | |
show link-oam interface GigabitEthernet
show link-oam link-monitor [ | | interface | statistics | status ]
Parameter
| Output modifiers
interface Interface status and configuration
link-monitor Display link-monitor status parameters
Current session privilege is 15.
Elapsed time is 0 day 0 hour 26 min 52 sec.
Idle time is 0 day 0 hour 0 min 0 sec.
AW-IHT-1271#
AW-IHT-1271# show line alive
Line is con 0.
* You are at this line now.
Alive from Console.
Default privileged level is 2.
Command line editing is enabled
Display EXEC banner is enabled.
Display Day banner is enabled.
Terminal width is 80.
length is 24.
history size is 32.
exec-timeout is 10 min 0 second.
statistics Display statistics parameters
status Display local and remote node status parameters
begin Begin with the line that matches
exclude Exclude lines that match
include Include lines that match
String to match output lines
* All switches or All ports
GigabitEthernet 1 Gigabit Ethernet Port
Port list for all port types
EXAMPLE
lldp
Display LLDP neighbors information..
SYNTAX
show lldp med media-vlan-policy [ <0~31> ] [ | {begin | exclude | include }
show lldp med remote-device [ interface
show lldp neighbors [ interface
show lldp statistics [ interface
Parameter
AW-IHT-1271# show link-oam interface * 1/10
Interface Control Mode Status
-------------------- --------- ------- -----------
GigabitEthernet 1/10 disabled passive non operational
AW-IHT-1271#
med Display LLDP-MED neighbors information.
neighbors Display LLDP neighbors information.
statistics Display LLDP statistics information.
media-vlan-policy Display media vlan policies.
remote-device Display remote device LLDP-MED neighbors information.
<0~31> List of policies.
Interface
GigabitEthernet
* All Switches or All ports
Gigabitethernet 1 Gigabit Ethernet Port
Port list in 1/1-12 for Gigabitethernet
| Output modifiers
begin Begin with the line that matches
exclude Exclude lines that match
include Include lines that match
String to match output lines
EXAMPLE
logging
Syslog.
SYNTAX
show logging
show logging [ info ] [ warning ] [ error ] [ | {begin | exclude | include }
AW-IHT-1271# show lldp med media-vlan-policy
No policies defined
AW-IHT-1271#
Parameter
Logging ID
error Error
info Information
warning Warning
| Output modifiers
begin Begin with the line that matches
exclude Exclude lines that match
include Include lines that match
String to match output lines
EXAMPLE
Error : 0
All : 161
ID Level Time Message
---- ------ ------------------------- -----------------------------
1 Info 1970-01-01T00:00:00+00:00 Switch just made a cold boot.
2 Info 1970-01-01T00:00:03+00:00 Link up on port 1
161 Info 1970-01-01T02:25:55+00:00 Link down on port 1
AW-IHT-1271#
AW-IHT-1271# show logging info
Switch logging host mode is disabled
Switch logging host address is null
Switch logging level is information
Number of entries:
Info : 3
Warning: 158
loop-protect
Loop protection configuration.
SYNTAX
show loop-protect [ interface
Parameter
interface Interface status and configuration
GigabitEthernet
* All Switches or All ports
Gigabitethernet 1 Gigabit Ethernet Port
Port list in 1/1-12 for Gigabitethernet
EXAMPLE
AW-IHT-1271# show loop-protect
Loop Protection Configuration
======================================
Loop Protection : Enable
Transmission Time : 1 sec
Shutdown Time : 180 sec
GigabitEthernet 1/1
------------------------------
Loop protect mode is enabled.
Actions are both of shutdown and log.
mac
Mac Address Table information.
SYNTAX
show mac address-table [ conf | static | aging-time | { { learning | count } [ interface
Parameter
address-table Mac Address Table
conf User added static mac addresses
static All static mac addresses
aging-time Aging time
learning Learn/disable/secure state
count Total number of mac addresses
interface Select an interface to configure
Gigabitethernet
* All switches or All ports
Gigabitethernet 1 Gigabit Ethernet Port
Port list in 1/1-12
Transmit mode is enabled.
No loop.
The number of loops is 0.
Status is down.
GigabitEthernet 1/2
------------------------------
Loop protect mode is enabled.
-- more --, next page: Space, continue: g, quit: ^C No loop.
address MAC address lookup
48 bit MAC address: xx:xx:xx:xx:xx:xx
vlan VLAN lookup
VLAN IDs 1-4095
vlan Addresses in this VLAN
VLAN IDs 1-4095
interface Select an interface to configure
igabitethernet
* All Switches or All ports
Gigabitethernet 1 Gigabit Ethernet Port
Port list in 1/1-12 for Gigabitethernet
| Output modifiers
begin Begin with the line that matches
exclude Exclude lines that match
include Include lines that match
String to match output lines
EXAMPLE
mep
Maintenance Entity Point
SYNTAX
show mep [ | ( begin | exclude | include )
show mep
AW-IHT-1271# show mac address-table static
AW-IHT-1271#
show mep ( ais | aps | bfd | cc | client | dm | lb | lck | lm | lm-avail | lst | lt | peer | pm | rt | syslog | tlv | tst ) [ | |
show mep ( detail | lm-hli ) [ | |
peer | pm | rt | syslog | tlv | tst ]
Parameter
alive Display information about alive lines
begin Begin with the line that matches
| Output modifiers
The range of MEP instances
ais Show AIS state
aps Sho APS state
bfd show BFD state
cc Show CC state
client Show Client state
detail Show detailed state including configuration information.
dm Show DM state
lb Show LB state
lck Show LCK state
lm Show LM state
lm-avail show Availability state
lm-hli show LM HLI state
lst show LST state
lt Show LT state
peer Show peer mep state
pm Show PM state
rt show RT state
syslog Show Syslog state
tlv show TLV state
tst Show TST state
begin Begin with the line that matches
exclude Exclude lines that match
include Include lines that match
String to match output lines
EXAMPLE
monitor
Monitoring different system events
SYNTAX
show monitor
show monitor session [ <1> | all | remote ]
Parameter
session MIRROR session
<1> MIRROR session number
all Show all MIRROR sessions
remote Show only Remote MIRROR sessions
AW-IHT-1271# show mep tst
MEP TST state is:
Inst TX frame count RX frame count RX rate Test time
AW-IHT-1271#
EXAMPLE
mvr
Multicast VLAN Registration configuration.
SYNTAX
show mvr [ vlan
[ sfm-information ] ] [ detail ] [ | {begin | exclude | include }
Parameter
vlan Search by VLAN
MVR multicast VLAN list
name Search by MVR name
MVR multicast VLAN name
group-database Multicast group database from MVR
interface Search by port
* or Gigabitethernet
* All Switches or All ports
Gigabitethernet 1 Gigabit Ethernet Port
Port list in 1/1-12 for Gigabitethernet
sfm-information Including source filter multicast information from MVR
AW-IHT-1271# show monitor
Session 1
---------
Mode : Disabled
Type : Mirror
Source VLAN(s) :
CPU Port :
AW-IHT-1271#
detail Detail information/statistics of MVR group database
| Output modifiers
begin Begin with the line that matches
exclude Exclude lines that match
include Include lines that match
String to match output lines
EXAMPLE
platform
Platform specific information
SYNTAX
show platform phy [ interface (
show platform phy id [ interface (
show platform phy instance [ | {begin | exclude | include }
show platform phy status [ interface (
Parameter
phy PHYs information
| Output modifiers
begin Begin with the line that matches
exclude Exclude lines that match
include Include lines that match
AW-IHT-1271# show mvr vlan 10 detail
MVR is currently disabled, please enable MVR to start group registration.
% Invalid MVR IGMP VLAN 10.
% Invalid MVR MLD VLAN 10.
AW-IHT-1271#
String to match output lines
EXAMPLE
poe
show poe.
SYNTAX
show poe auto-check [ interface (
show poe config [ interface (
show poe power-delay [ interface (
show poe schedule [ interface (
show poe status [ interface (
Parameter
interface
| Output modifiers
AW-IHT-1271# show platform phy
Port API Inst WAN/LAN/1G Mode Duplex Speed Link
---- --------- --------- ---- ------ ----- ----
1 Default 1G PD - - ,No
2 Default 1G PD - - ,No
3 Default 1G PD - - ,No
4 Default 1G PD - - ,Yes
5 Default 1G PD - - ,No
6 Default 1G PD - - ,No
7 Default 1G PD - - ,No
8 Default 1G PD - - ,No
9 Default 1G PD - - ,No
10 Default 1G PD - - ,No
11 Default 1G PD - - ,No
12 Default 1G PD - - ,No
begin Begin with the line that matches
exclude Exclude lines that match
include Include lines that match
String to match output lines
EXAMPLE
ntp
show NTP.
SYNTAX
show ntp status
Parameter
status status
EXAMPLE
AW-IHT-1271# show poe status interface GigabitEthernet 1/1-2
Interface PD Class Port Status Pwr
Req Pwr Alloc Power Current Priority
Used
[W] Used[W] Used[W] Used[mA]
----------------------- --------- -----------------------------------------
----
--- --------- ------- -------- --------
GigabitEthernet 1/1 - PoE turned OFF - PoE disabled 30
0 0.0 0 Low
GigabitEthernet 1/2 - PoE turned OFF - PoE disabled 30
0 0.0 0 Low
Total Power Request : 60.0 [W]
Total Power Alloctaed : 0.0 [W]
Total Power Used : 0.0 [W]
Total Current Used : 0 [mA]
AW-IHT-1271#
port-security
SYNTAX
show port-security port [ interface
show port-security switch [ interface
Parameter
port Show MAC Addresses learned by Port Security
switch Show Port Security status.
Interface
GigabitEthernet
* All Switches or All ports
Gigabitethernet 1 Gigabit Ethernet Port
Port list in 1/1-12 for Gigabitethernet
| Output modifiers
begin Begin with the line that matches
exclude Exclude lines that match
include Include lines that match
String to match output lines
AW-IHT-1271# show ntp status
NTP Mode : disabled
Idx Server IP host address (a.b.c.d) or a host name string
--- ------------------------------------------------------
1
2
3
4
5
AW-IHT-1271#
EXAMPLE
privilege
SYNTAX
show privilege [ | {begin | exclude | include }
Parameter
| Output modifiers
begin Begin with the line that matches
exclude Exclude lines that match
include Include lines that match
EXAMPLE
AW-IHT-1271# show privilege
--------------------------------------------
| The order is as the input sequence and |
| the last one has the highest priority. |
--------------------------------------------
privilege line level 5 LINE
AW-IHT-1271# show port-security port interface GigabitEthernet 1/2
GigabitEthernet 1/2
-------------------
MAC Address VID State Added Age/Hold Time
----------------- ---- ---------- -------------------- -------------
AW-IHT-1271#
process
process
SYNTAX
show process list
show process list [ | | detail ] ( begin | exclude | include )
show process list detail
show process load
Parameter
list list
load load
| Output modifiers
detail optionally show thread call stack
exclude Exclude lines that match
include Include lines that match
String to match output lines
EXAMPLE
ptp
Precision time Protocol (1588)
SYNTAX
show ptp <0-3> ( clk | current | default | filter ) | ( begin | exclude | include )
AW-IHT-1271# show process load
Load average(100ms, 1s, 10s): 9%, 2%, 2%
AW-IHT-1271#
show ptp <0-3> [ foreign-master-record | port-ds | port-state ] [ | | ( interface ( * | GigabitEthernet )
show ptp <0-3> [ ho | local-clock | master-table-unicast | parent | servo | servo-extended | slave | slave-cfg |
slave-table-unicast | time-property | uni] | ( begin | exclude | include )
Parameter
<0-3> Show various PTP data
ext Show the 1PPS and External clock output configuration and vcxo frequency rate
adjustment option.
system-time Show the PTP <-> system time synchronization mode.
clk Show PTP slave clock options parameters.
current Show PTP current data set (IEEE1588 paragraph 8.2.2).
default Show PTP default data set (IEEE1588 paragraph 8.2.1).
filter Show PTP filter parameters.
foreign-master-record Show PTP port foreign masters.
ho Show PTP slave holdover parameters.
local-clock Show local clock current time
master-table-unicast Show PTP master list of connected unicast slaves.
parent Show PTP parent data set (IEEE1588 paragraph 8.2.3).
port-ds Show PTP port data set (IEEE1588 paragraph 8.2.5).
port-state Show PTP port state.
servo Show PTP servo parameters.
servo-extended Show PTP servo extended parameters.
slave Show PTP slave clock lock threshold parameters.
slave-cfg Show slave lock configuration
slave-table-unicast Show the Unicast slave table of the requested unicast masters
time-property Show PTP time properties data set (IEEE1588 paragraph 8.2.4).
uni Show PTP slave unicast configuration parameters.
wireless Show PTP port wireless parameters.
| Output modifiers
begin Begin with the line that matches
exclude Exclude lines that match
include Include lines that match
String to match output lines
interface Define interface list for the 'port' show commands. Default is show all interfaces.
* All switches or All ports
GigabitEthernet 1 Gigabit Ethernet Port
Port list for all port types
EXAMPLE
pvlan
PVLAN status.
SYNTAX
show pvlan
show pvlan isolation interface
Parameter
PVLAN id to show configuration for
isolation show isolation configuration
GigabitEthernet
AW-IHT-1271# show ptp 3 master-table-unicast
ip_addr mac_addr port Ann Sync
--------------- ----------------- ---- --- -----
AW-IHT-1271#
* All Switches or All ports
Gigabitethernet 1 Gigabit Ethernet Port
Port list in 1/1-12 for Gigabitethernet
| Output modifiers
begin Begin with the line that matches
exclude Exclude lines that match
include Include lines that match
String to match output lines
EXAMPLE
qos
Quality of Service.
SYNTAX
show qos [ { interface [
[ dscp-classify ] [ cos-dscp ] [ dscp-egress-translation ] } | storm | { qce [
include }
Parameter
interface Interface
GigabitEthernet
* All switches or All ports
Gigabitethernet 1 Gigabit Ethernet Port
AW-IHT-1271# show pvlan isolation interface GigabitEthernet 1/1-2
Port Isolation
-------------------------------- ---------
GigabitEthernet 1/1 Disabled
GigabitEthernet 1/2 Disabled
AW-IHT-1271#
Port list in 1/1-12 for Gigabitethernet
maps Global QoS Maps/Tables
qce QoS Control Entry
storm Storm policer
wred Weighted Random Early Discard
cos-dscp Map for cos to dscp
dscp-classify Map for dscp classify enable
dscp-cos Map for dscp to cos
dscp-egress-translation Map for dscp egress translation
dscp-ingress-translation Map for dscp ingress translation
QCE ID
| Output modifiers
begin Begin with the line that matches
exclude Exclude lines that match
include Include lines that match
String to match output lines
EXAMPLE
radius-server
RADIUS configuration.
AW-IHT-1271# show qos storm
qos storm:
==========
Unicast : disabled 1
Multicast: disabled 1
Broadcast: disabled 1
AW-IHT-1271#
SYNTAX
show radius-server [statistics] [ | {begin | exclude | include }
Parameter
statistics RADIUS statistics
| Output modifiers
begin Begin with the line that matches
exclude Exclude lines that match
include Include lines that match
String to match output lines
EXAMPLE
rapid-ring
Display Rapid Ring configurations
SYNTAX
show rapid-ring
show rapid-ring ( begin | exclude | include )
Parameter
| Output modifiers
begin Begin with the line that matches
AW-IHT-1271# show radius-server
Global RADIUS Server Timeout : 5 seconds
Global RADIUS Server Retransmit : 3 times
Global RADIUS Server Deadtime : 0 minutes
Global RADIUS Server Key :
Global RADIUS Server Attribute 4 :
Global RADIUS Server Attribute 95 :
Global RADIUS Server Attribute 32 :
No hosts configured!
AW-IHT-1271#
exclude Exclude lines that match
include Include lines that match
String to match output lines
EXAMPLE
rmon
RMON statistics.
SYNTAX
show rmon alarm [ <1~65535> ] [ | {begin | exclude | include }
show rmon event [ <1~65535> ] [ | {begin | exclude | include }
show rmon history [ <1~65535> ] [ | {begin | exclude | include }
show rmon statistics [ <1~65535> ] [ | {begin | exclude | include }
AW-IHT-1271# show rapid-ring
Entry Index : 1
Rapid Ring Role : Disabled
Rapid Ring Port 1 : 1
Rapid Ring Port 2 : 1
Rapid Ring Port 1 State : Discarding
Rapid Ring Port 2 State : Discarding
Entry Index : 2
Rapid Ring Role : Disabled
Rapid Ring Port 1 : 1
Rapid Ring Port 2 : 1
Rapid Ring Port 1 State : Forwarding
Rapid Ring Port 2 State : Forwarding
Ring-to-Ring Role : Disabled
Ring-to-Ring Port : 1
Ring-to-Ring Port State : Forwarding
AW-IHT-1271#
Parameter
alarm Display the RMON alarm table
event Display the RMON event table
history Display the RMON history table
statistics Display the RMON statistics table
<1~65535> Alarm/Event/History/Statistics entry list
| Output modifiers
begin Begin with the line that matches
exclude Exclude lines that match
include Include lines that match
String to match output lines
EXAMPLE
running-config
Show running system information.
SYNTAX
show running-config [ all-defaults ] [ | {begin | exclude | include }
show running-config feature
show running-config interface
show running-config interface vlan
show running-config line { console | vty }
show running-config vlan
Parameter
all-defaults Include most/all default values
AW-IHT-1271# show rmon alarm
AW-IHT-1271#
feature Show configuration for specific feature
interface Show specific interface(s)
line Show line settings
vlan VLAN
CWORD Valid words are GVRP 'access' 'access-list'
'aggregation' 'arp-inspection' 'auth' 'clock'
'dhcp' 'dhcp-snooping' 'dns' 'dot1x' 'green-ethernet' 'http' 'icli'
'ip-igmp-snooping' 'ip-igmp-snooping-port'
'ip-igmp-snooping-vlan' 'ipmc-profile'
'ipmc-profile-range' 'ipv4' 'ipv6'
'ipv6-mld-snooping' 'ipv6-mld-snooping-port' 'ipv6-mld-snooping-vlan'
lacp 'lldp' 'logging' 'loop-protect' 'mac' 'mep'
'monitor' 'mstp' 'mvr' 'mvr-port' 'ntp' phy poe 'port'
'port-security' 'pvlan' 'qos' 'rmon' sflow
'snmp' 'source-guard' 'ssh' system 'upnp' 'user'
'vlan' 'voice-vlan'
'web-privilege-group-level'
GigabitEthernet
* All switches or All ports
Gigabitethernet 1 Gigabit Ethernet Port
Port list in 1/1-12 for Gigabitethernet
List of VLAN numbers
console Console
vty VTY
List of console/VTYs
| Output modifiers
begin Begin with the line that matches
exclude Exclude lines that match
include Include lines that match
String to match output lines
EXAMPLE
sflow
Statistics flow..
SYNTAX
show sflow [ statistics { receiver | samplers [[
include }
Parameter
statistics sFlow statistics.
receiver Show statistics for receiver.
samplers Show statistics for samplers.
runtime, see sflow_icli_functions.c
GigabitEthernet
* All switches or All ports
Gigabitethernet 1 Gigabit Ethernet Port
Port list in 1/1-12 for Gigabitethernet
| Output modifiers
begin Begin with the line that matches
exclude Exclude lines that match
AW-IHT-1271# show running-config interface vlan 3
Building configuration...
end
AW-IHT-1271#
include Include lines that match
String to match output lines
EXAMPLE
smtp
Show email information
SYNTAX
show smtp
EXAMPLE
AW-IHT-1271# show sflow
Agent Configuration:
====================
Agent Address: 127.0.0.1
Receiver Configuration:
=======================
Owner :
Receiver : 0.0.0.0
UDP Port : 6343
Max. Datagram: 1400 bytes
Time left : 0 seconds
No enabled collectors (receivers). Skipping displaying per-port info.
AW-IHT-1271#
snmp
Display SNMP configurations.
SYNTAX
show snmp
show snmp access [
include }
show snmp community v3 [
show snmp host [
show snmp security-to-group [ { v1 | v2c | v3 }
show snmp user [
show snmp view [
Parameter
access access configuration
Group name
v1 v1 security model
AW-IHT-1271# show smtp
Mail Server :
User Name :
Password :
Sender :
Return Path :
Email Adress 1 :
Email Adress 2 :
Email Adress 3 :
Email Adress 4 :
Email Adress 5 :
Email Adress 6 :
AW-IHT-1271#
v2c v2c security model
v3 v3 security model
any any security model
auth authNoPriv Security Level
noauth noAuthNoPriv Security Level
priv authPriv Security Level
community Community
v3 SNMPv3
Specify community name
host Set SNMP host's configurations
Name of the host configuration
system System event group
switch Switch event group
interface Interface event group
aaa AAA event group
security-to-group security-to-group configuration
security group name
user User
Security user name
Security Engine ID
view MIB view configuration
MIB view name
MIB view OID
| Output modifiers
begin Begin with the line that matches
exclude Exclude lines that match
include Include lines that match
String to match output lines
EXAMPLE
spanning-tree
STP Bridge.
SYNTAX
show spanning-tree [ summary | active | { interface
AW-IHT-1271# show snmp
SNMP Configuration
SNMP Mode : enabled
SNMP Version : 2c
Read Community : public
Write Community : private
Trap Mode : disabled
Trap Version : 1
SNMPv3 Communities Table:
Community : public
Source IP : 0.0.0.0
Source Mask : 0.0.0.0
Community : private
Source IP : 0.0.0.0
Source Mask : 0.0.0.0
SNMPv3 Users Table:
User Name : default_user
Engine ID : 800007e5017f000001
-- more --, next page: Space, continue: g, quit: ^C
{begin | exclude | include }
Parameter
summary STP summary
active STP active interfaces
interface Choose port
Gigabitethernet
* All switches or All ports
Gigabitethernet 1 Gigabit Ethernet Port
Port list in 1/1-12 for Gigabitethernet
detailed STP statistics
interface List of port type and port ID, ex, 1/1-12
mst Configuration
configuration STP bridge instance no (0-7, CIST=0, MST2=1...)
<0-7> Choose port
GigabitEthernet
* All Switches or All ports
Gigabitethernet 1 Gigabit Ethernet Port
Port list in 1/1-12 for Gigabitethernet
| Output modifiers
begin Begin with the line that matches
exclude Exclude lines that match
include Include lines that match
String to match output lines
EXAMPLE
AW-IHT-1271# show snmp
SNMP Configuration
SNMP Mode : enabled
SNMP Version : 2c
Read Community : public
Write Community : private
Trap Mode : disabled
Trap Version : 1
SNMPv3 Communities Table:
Community : public
Source IP : 0.0.0.0
Source Mask : 0.0.0.0
Community : private
Source IP : 0.0.0.0
Source Mask : 0.0.0.0
SNMPv3 Users Table:
User Name : default_user
Engine ID : 800007e5017f000001
AW-IHT-1271# show spanning-tree ?
| Output modifiers
active STP active interfaces
detailed STP statistics
interface Choose port
mst Configuration
summary STP summary
AW-IHT-1271# show spanning-tree
CIST Bridge STP Status
Bridge ID : 32768.00-40-C7-01-02-03
Root ID : 32768.00-40-C7-01-02-03
Root Port : -
Root PathCost: 0
Regional Root: 32768.00-40-C7-01-02-03
Int. PathCost: 0
Max Hops : 20
TC Flag : Steady
TC Count : 0
TC Last : -
switchalert-management
Show SwitchAlert Management information
SYNTAX
show switchalert-management [ cloud-config | mobile-device-list | port-name-service ]
Parameter
cloud-config Show SwitchAlert Management configuration
mobile-device-list Show Registered Mobile Device List
port-name-service Show Port Name Service configuration
EXAMPLE
switchport
Display switching mode characteristics.
SYNTAX
show switchport forbidden [ { vlan
Parameter
forbidden Lookup VLAN Forbidden port entry.
name name - Show forbidden access for specific VLAN name.
vlan vid - Show forbidden access for specific VLAN id.
VLAN id
VLAN name
AW-IHT-1271# show switchalert-management cloud-config
SwitchAlert Mode : disabled
Server Address : ipush.cloudapp.net
Server State :
AW-IHT-1271#
| Output modifiers
begin Begin with the line that matches
exclude Exclude lines that match
include Include lines that match
String to match output lines
EXAMPLE
tacacs-server
TACACS+ configuration.
SYNTAX
show tacacs-server [ | {begin | exclude | include }
Parameter
| Output modifiers
begin Begin with the line that matches
exclude Exclude lines that match
include Include lines that match
String to match output lines
EXAMPLE
AW-IHT-1271# show tacacs-server
Global TACACS+ Server Timeout : 5 seconds
Global TACACS+ Server Deadtime : 0 minutes
Global TACACS+ Server Key :
No hosts configured!
AW-IHT-1271#
AW-IHT-1271# show switchport forbidden
Forbidden VLAN table is empty
AW-IHT-1271#
system
show system information.
SYNTAX
show system
Parameter
None
EXAMPLE
AW-IHT-1271# show system
Model Name :
System Description :
Location :
Contact :
System Name :
System Date : 2011-01-01T07:54:13+00:00
System Uptime : 07:54:14
Bootloader Version : v1.15f
Firmware Version : v7.10.1049 2017-04-11
Hardware Version : v1.01
Mechanical Version :
Serial Number :
MAC Address : 00-00-8c-78-91-23
Memory : Total=52065 KBytes, Free=32998 KBytes,
Max=31857 KBytes
FLASH : 0x40000000-0x41ffffff, 512 x 0x10000 blocks
Powers status : Normal
Powers : PWR_1.0V:0.98V; PWR_3.3V:3.29V;
PWR_2.5V:2.57V; PWR_1.8V:1.87V
Temperature status : Normal
Temperature 1 : 46(C) ; 114(F)
Temperature 2 : 46(C) ; 114(F)
AW-IHT-1271#
terminal
Display terminal configuration parameters.
SYNTAX
show terminal [ | {begin | exclude | include }
Parameter
| Output modifiers
begin Begin with the line that matches
exclude Exclude lines that match
include Include lines that match
String to match output lines
EXAMPLE
AW-IHT-1271# show terminal
Line is con 0.
* You are at this line now.
Alive from Console.
Default privileged level is 2.
Command line editing is enabled
Display EXEC banner is enabled.
Display Day banner is enabled.
Terminal width is 80.
length is 24.
history size is 32.
exec-timeout is 10 min 0 second.
Current session privilege is 15.
Elapsed time is 0 day 0 hour 29 min 24 sec.
Idle time is 0 day 0 hour 0 min 0 sec.
AW-IHT-1271#
udld
Unidirectional Link Detection(UDLD) configurations, statistics and status
SYNTAX
show udld
show udld | [ begin | exclude | include ]
show udld interface [ * | GigabitEthernet
Parameter
| Output modifiers
Interface Choose port
begin Begin with the line that matches
exclude Exclude lines that match
include Include lines that match
String to match output lines
* All switches or All ports
GigabitEthernet 1 Gigabit Ethernet Port
Port list for all port types
EXAMPLE
AW-IHT-1271# show udld interface GigabitEthernet 1/1-3
GigabitEthernet 1/1
----------------------------------------------------------------------
UDLD Mode : Disable
Admin State : Disable
Message Time Interval(Sec): 7
Device ID(local) : 00-00-8C-78-91-23
Device Name(local) : AW-IHT-1271
Bidirectional state : Indeterminant
No neighbor cache information stored
---------------------
upnp
Display UPnP configurations.
SYNTAX
show upnp [ | {begin | exclude | include }
Parameter
| Output modifiers
begin Begin with the line that matches
exclude Exclude lines that match
GigabitEthernet 1/2
----------------------------------------------------------------------
UDLD Mode : Disable
Admin State : Disable
Message Time Interval(Sec): 7
Device ID(local) : 00-00-8C-78-91-23
Device Name(local) : AW-IHT-1271
Bidirectional state : Indeterminant
No neighbor cache information stored
---------------------
GigabitEthernet 1/3
----------------------------------------------------------------------
UDLD Mode : Disable
Admin State : Disable
Message Time Interval(Sec): 7
Device ID(local) : 00-00-8C-78-91-23
Device Name(local) : AW-IHT-1271
Bidirectional state : Indeterminant
No neighbor cache information stored
---------------------
AW-IHT-1271#
include Include lines that match
String to match output lines
EXAMPLE
user-privilege
Users privilege configuration
SYNTAX
show user-privilege
EXAMPLE
users
Display information about terminal lines.
SYNTAX
show users myself [ | {begin | exclude | include }
Parameter
myself Display information about mine
| Output modifiers
begin Begin with the line that matches
AW-IHT-1271# show user-privilege
username admin privilege 15 password none
AW-IHT-1271#
AW-IHT-1271# show upnp
UPnP Mode : Disabled
UPnP TTL : 4
UPnP Advertising Duration : 100
AW-IHT-1271#
exclude Exclude lines that match
include Include lines that match
String to match output lines
EXAMPLE
version
System hardware and software status.
SYNTAX
show version [ | {begin | exclude | include }
Parameter
| Output modifiers
begin Begin with the line that matches
exclude Exclude lines that match
include Include lines that match
String to match output lines
EXAMPLE
AW-IHT-1271# show user myself
Line is vty 0.
* You are at this line now.
Connection is from 192.168.10.119:4123 by Telnet.
User name is admin.
Privilege is 15.
Elapsed time is 0 day 1 hour 33 min 27 sec.
Idle time is 0 day 0 hour 0 min 0 sec.
AW-IHT-1271# show version
MEMORY : Total=76031 KBytes, Free=57621 KBytes, Max=56469 KBytes
FLASH : 0x40000000-0x41ffffff, 512 x 0x10000 blocks
MAC Address : 80-34-57-13-03-bd
Previous Restart : Cold
System Contact :
System Name :
System Location :
System Time : 2016-09-30T14:52:34+00:00
System Uptime : 01:43:12
Active Image
------------
Image : managed
Version : AW-IHT-1271 (standalone) v7.04.724
Date : 2016-08-18T10:11:49+08:00
Alternate Image
---------------
Image : managed.bk
Version :
Date :
------------------
SID : 1
------------------
Chipset ID : VSC0
Board Type : AW-IHT-1271
Port Count : 26
Product : Vitesse AW-IHT-1271 Switch
Software Version : AW-IHT-1271 (standalone) v6.02
Build Date : 2016-09-30T13:35:25+08:00
AW-IHT-1271#
vlan
VLAN status.
SYNTAX
show vlan [ id
show vlan protocol [ eth2 { <0x600-0xffff> | arp | ip | ipx | at } ] [ snap { <0x0-0xffffff> | rfc_1042 | snap_8021h }
<0x0-0xffff> ] [ llc <0x0-0xff> <0x0-0xff> ]
show vlan status [admin [interface] | all | combined | conflicts | gvrp | interface | mstp | mvr | nas | vcl | voice-vlan ]
[
Parameter
id VLAN status by VLAN id
VLAN IDs 1-4095
name VLAN status by VLAN name
A VLAN name
brief VLAN summary information
protocol Protocol-based VLAN status
eth2 Ethernet protocol based VLAN status
<0x600-0xffff> Ether Type(Range: 0x600 - 0xFFFF)
arp Ether Type is ARP
ip Ether Type is IP
ipx Ether Type is IPX
at Ether Type is AppleTalk
snap SNAP-based VLAN status
<0x0-0xffffff> SNAP OUI (Range 0x000000 - 0XFFFFFF)
rfc_1042 SNAP OUI is rfc_1042
snap_8021h SNAP OUI is 8021h
<0x0-0xffff> PID (Range: 0x0 - 0xFFFF)
llc LLC-based VLAN status
<0x0-0xff> DSAP (Range: 0x00 - 0xFF)
<0x0-0xff> SSAP (Range: 0x00 - 0xFF)
admin Show the VLANs configured by administrator.
all Show all VLANs configured.
combined Show the VLANs configured by a combination.
conflicts Show VLANs configurations that has conflicts.
gvrp Show the VLANs configured by GVRP.
interface Show the VLANs configured for a specific interface(s).
mstp Show the VLANs configured by MSTP.
mvr Show the VLANs configured by MVR.
nas Show the VLANs configured by NAS.
vcl Show the VLANs configured by VCL.
voice-vlan Show the VLANs configured by Voice VLAN.
interface Show the VLANs configured for a specific interface(s).
GigabitEthernet
Gigabitethernet 1 Gigabit Ethernet Port
Port list in 1/1-12 for Gigabitethernet
EXAMPLE
AW-IHT-1271# show vlan
VLAN Name Interfaces
---- -------------------------------- ----------
1 default Gi 1/1-12
AW-IHT-1271#
voice
Voice appliance attributes.
SYNTAX
show voice vlan [ oui
Parameter
vlan Vlan for voice traffic
oui OUI configuration
OUI value
interface Select an interface to configure
* or Gigabitethernet
* All Switches or All ports
Gigabitethernet 1 Gigabit Ethernet Port
Port list in 1/1-12 for Gigabitethernet
| Output modifiers
begin Begin with the line that matches
exclude Exclude lines that match
include Include lines that match
String to match output lines
EXAMPLE
web
web.
SYNTAX
show web privilege group [
Parameter
privilege Web privilege
group Web privilege group
GigabitEthernet 1/1 :
---------------------
GigabitEthernet 1/1 switchport voice vlan mode is disabled
GigabitEthernet 1/1 switchport voice security is disabled
GigabitEthernet 1/1 switchport voice discovery protocol is oui
-- more --, next page: Space, continue: g, quit: ^C
AW-IHT-1271# show voice vlan
Switch voice vlan is disabled
Switch voice vlan ID is 1000
Switch voice vlan aging-time is 86400 seconds
Switch voice vlan traffic class is 7
Telephony OUI Description
------------- -----------
00-01-E3 Siemens AG phones
00-03-6B Cisco phones
00-0F-E2 H3C phones
00-60-B9 Philips and NEC AG phones
00-D0-1E Pingtel phones
00-E0-75 Polycom phones
00-E0-BB 3Com phones
Voice VLAN switchport is configured on following:
CWORD Valid words are 'Aggregation' DHCP 'Debug' 'Dhcp_Client' Diagnostics
EEE GARP GVRP 'Green_Ethernet' 'IP2' 'IPMC_Snooping' 'LACP' 'LLDP'
'Loop_Protect' 'MAC_Table' 'MVR' 'Maintenance'
'Mirroring' 'NTP' 'POE' 'Ports' 'Private_VLANs' 'QoS'
'RPC' 'Security' 'Spanning_Tree' 'System' 'Timer'
'UPnP' 'VCL' 'VLANs' 'Voice_VLAN' XXRP sFlow
'sFlow'
level Web privilege group level
| Output modifiers
begin Begin with the line that matches
exclude Exclude lines that match
include Include lines that match
String to match output lines
EXAMPLE
AW-IHT-1271# show web privilege group level
Group Name Privilege Level
CRO CRW SRO SRW
-------------------------------- --- --- --- ---
ACTIVATE 5 10 5 10
Aggregation 5 10 5 10
cloud_management 5 10 5 10
Debug 15 15 15 15
DHCP 5 10 5 10
Dhcp_Client 5 10 5 10
Diagnostics 5 10 5 10
EEE 5 10 5 10
GARP 5 10 5 10
Green_Ethernet 5 10 5 10
GVRP 5 10 5 10
IP2 5 10 5 10
IPMC_Snooping 5 10 5 10
LACP 5 10 5 10
LLDP 5 10 5 10
Loop_Protect 5 10 5 10
MAC_Table 5 10 5 10
Maintenance 15 15 15 15
Mirroring 5 10 5 10
MVR 5 10 5 10
NTP 5 10 5 10
POE 5 10 5 10
Ports 5 10 1 10
Private_VLANs 5 10 5 10
QoS 5 10 5 10
RPC 5 10 5 10
Security 5 10 5 10
sFlow 5 10 5 10
Spanning_Tree 5 10 5 10
System 5 10 1 10
Timer 5 10 5 10
Trap_Event 5 10 5 10
Trouble_Shooting 5 10 5 10
UPnP 5 10 5 10
VCL 5 10 5 10
VLANs 5 10 5 10
Voice_VLAN 5 10 5 10
VTUN 5 10 5 10
XXRP 5 10 5 10
23 TERMINAL of CLI
Set terminal line parameters
Syntax
terminal editing
terminal exec-timeout <0-1440> [ <0-3600> ]
terminal help
terminal history size <0-32>
terminal length <0 or 3-512>
terminal width <0 or 40-512>
Parameter
editing Enable command line editing
exec-timeout Set the EXEC timeout
help Description of the interactive help system
history Control the command history function
length Set number of lines on a screen
width Set width of the display terminal
<0-1440> Timeout in minutes
<0-3600> Timeout in seconds
size Set history buffer size
<0-32> Number of history commands, 0 means disable
<0 or 3-512> Number of lines on screen (0 for no pausing)
<0 or 40-512> Number of characters on a screen line (0 for unlimited width)
EXAMPLE
AW-IHT-1271# terminal help
Help may be requested at any point in a command by entering
a question mark '?'. If nothing matches, the help list will
be empty and you must backup until entering a '?' shows the
available options.
Two styles of help are provided:
1. Full help is available when you are ready to enter a
command argument (e.g. 'show ?') and describes each possible
argument.
2. Partial help is provided when an abbreviated argument is entered
and you want to know what arguments match the input
(e.g. 'show pr?'.)
AW-IHT-1271#
24 TRACEROUTE of CLI
Copy from source to destination
SYNTAX
traceroute ip
Parameter
ip IP
destination address
nqueries Specify number of probe packets
protocol Specify protocol including icmp, udp and tcp
ttl Specify max TTL
wait Specify wait time
EXAMPLE
AW-IHT-1271# traceroute ip 22 nqueries 3 protocol icmp ttl 3 wait 3
traceroute to 22 (0.0.0.22), 3 hops max, 140 byte packets
1 * * *
2 * * *
3 * * *
AW-IHT-1271#
20 CLI COMMAND REFERENCEs
This chapter introduces the CLI privilege level and command modes.
The privilege level determines whether or not the user could run the particular commands
If the user could run the particular command, then the user has to run the command in the
correct mode.
23.1 Privilege level
Every command has a privilege level (0-15). Users can run a command if the sessions
privilege level is greater than or equal to the commands privilege level. The sessions
privilege level initially comes from the login accounts privilege level, though it is possible to
change the sessions privilege level after logging in.
PRIVILEGE LEVEL TYPES OF COMMANDS AT THIS PRIVILEGE LEVEL
0 Display basic system information
13 Configure features except for login accounts, the
authentication method
sequence, multiple logins, and administrator and enable
passwords.
15 Configure login accounts, the authentication method
sequence, multiple logins,
and administrator and enable passwords.
23.2 Command modes
The CLI is divided into several modes. If a user has enough privilege to run a particular
command, the user has to run the command in the correct mode. The modes that are available
depend on the sessions privilege level.
COMMAND MODE
Command Summary
COMMAND DESCRIPTION P M
show access management Use the show access management user
EXEC command without keywords to
display the access management
configuration, or use the statistics
keyword to display statistics, or use the
specific access management entry.
15 EXEC
clear access management statistics Use the clear access management
statistics privileged EXEC command to
clear the statistics maintained by access
management.
15 EXEC
access management Use the access management global
configuration command to enable the
access management. Use the no form
of this command to disable the access
management.
15 GLOBAL_CONFIG
access management <1-16> <1-4094>
[ telnet ] | all }
Use the access management
command to set the access
management entry for IPv4 address.
15 GLOBAL_CONFIG
access management <1-16> <1-4094>
[ telnet ] | all }
Use the access management
command to set the access
management entry for IPv6 address.
15 GLOBAL_CONFIG
no access management <1~16> Use the no access management
command to delete the specific access
management entry.
15 GLOBAL_CONFIG
access-list action { permit | deny } Use the access-list action interface
configuration command to configure
access-list action. The access-list
15 INTERFACE_PORT_LIST
interface configuration will affect the
received frames if it doesn't match any
ACE.
access-list rate-limiter <1-16> Use the access-list rate-limiter interface
configuration command to configure the
access-list rate-limiter ID . The
access-list interface configuration will
affect the received frames if it doesn't
match any ACE.
15 INTERFACE_PORT_LIST
no access-list rate-limiter Use the no access-list rate-limiter
interface configuration command to
disable the access-list rate-limiter. The
access-list interface configuration will
affect the received frames if it doesn't
match any ACE.
15 INTERFACE_PORT_LIST
access-list { redirect | port-copy } interface
{
Use the no access-list redirect interface
configuration command to configure the
access-list redirect interface.
15 INTERFACE_PORT_LIST
no access-list { redirect | port-copy } Use the no access-list redirect interface
configuration command to disable the
access-list redirect. The access-list
interface configuration will affect the
received frames if it doesn't match any
ACE.
15 INTERFACE_PORT_LIST
access-list mirror Use the access-list mirror interface
configuration command to enable
access-list mirror. Use the no form of
this command to disable access-list
mirror. The access-list interface
configuration will affect the received
frames if it doesn't match any ACE.
15 INTERFACE_PORT_LIST
access-list logging Use the access-list logging interface
configuration command to enable
access-list logging. Use the no form of
this command to disable access-list
logging. The access-list interface
configuration will affect the received
frames if it doesn't match any ACE.
15 INTERFACE_PORT_LIST
access-list shutdown Use the access-list shutdown interface
configuration command to enable
access-list shutdown. Use the no form
of this command to disable access-list
shutdown. The access-list interface
configuration will affect the received
frames if it doesn't match any ACE.
15 INTERFACE_PORT_LIST
access-list evc-policer <1-256> Use the access-list evc-policer interface
configuration command to configure the
access-list evc-policer ID. The
access-list interface configuration will
affect the received frames if it doesn't
match any ACE.
15 INTERFACE_PORT_LIST
no access-list evc-policer Use the no access-list evc-policer
interface configuration command to
configure the access-list evc-policer ID.
The access-list interface configuration
will affect the received frames if it
doesn't match any ACE.
15 INTERFACE_PORT_LIST
access-list policy <0-255> Use the access-list policy interface
configuration command to configure the
access-list policy value. The access-list
interface configuration will affect the
received frames if it doesn't match any
ACE.
15 INTERFACE_PORT_LIST
no access-list policy Use the no access-list policy interface
configuration command to restore the
default access-list policy ID. The
access-list interface configuration will
affect the received frames if it doesn't
match any ACE.
15 INTERFACE_PORT_LIST
access-list port-state Use the access-list port-state interface
configuration command to enable
access-list port state. Use the no form of
this command to disable access-list port
state.
15 INTERFACE_PORT_LIST
access-list rate-limiter [ <1~16> ] { pps
<1,2,4,8,16,32,64,128,256,512>| 100pps
Use the access-list rate-limiter global
configuration command to configure the
15 INTERFACE_PORT_LIST
<1-32767> | kpps
<1,2,4,8,16,32,64,128,256,512,1024> | 100kbps
<0-10000> }
access-list rate-limiter.
default access-list rate-limiter [ <1~16> ] Use the default access-list rate-limiter
global configuration command to restore
the default setting of access-list
rate-limiter.
15 GLOBAL_CONFIG
access-list ace [update] <1-256> [next
{<1-256>|last}] [ingress {switch
{
<0-255> [policy-bitmask <0x0-0xFF>]] [tag
{tagged|untagged|any}] [vid {<1-4095>|any}]
[tag-priority {<0-7>|0-1|2-3|4-5|6-7|0-3|4-7|any}]
[dmac-type {unicast|multicast|broadcast|any}]
[frametype { any| etype [etype-value
{<0x600-0x7ff,0x801-0x805,0x807-0x86dc,0x86de
-0xffff>|any}] [smac {
{
[dip {
{
{arp|rarp|other|any}] [arp-flag [arp-request
{<0-1>|any}] [arp-smac {<0-1>|any}] [arp-tmac
{<0-1>|any}] [arp-len {<0-1>|any}] [arp-ip
{<0-1>|any}] [arp-ether {<0-1>|any}]]| ipv4 [sip
{
[ip-protocol {<0,2-5,7-16,18-255>|any}] [ip-flag
[ip-ttl {<0-1>|any}] [ip-options {<0-1>|any}]
[ip-fragment {<0-1>|any}]]| ipv4-icmp [sip
{
[icmp-type {<0-255>|any}] [icmp-code
{<0-255>|any}] [ip-flag [ip-ttl {<0-1>|any}]
[ip-options {<0-1>|any}] [ip-fragment {<0-1>|any}]]|
ipv4-udp [sip {
{
<0-65535>]|any}] [dport {<0-65535> [to
<0-65535>]|any}] [ip-flag [ip-ttl {<0-1>|any}]
[ip-options {<0-1>|any}] [ip-fragment {<0-1>|any}]]|
Use the access-list ace global
configuration command to set the
access-list ace. The command without
the update keywrod will creates or
overwrites an existing ACE, any
unspecified parameter will be set to its
default value. Use the update keyword
to update an existing ACE and only
specified parameter are modified. The
ACE must ordered by an appropriate
sequence, the received frame will only
be hit on the first matched ACE. Use the
next or last keyword to adjust the ACE's
sequence order.
15 GLOBAL_CONFIG
ipv4-tcp [sip {
{
<0-65535>]|any}] [dport {<0-65535> [to
<0-65535>]|any}] [ip-flag [ip-ttl {<0-1>|any}]
[ip-options {<0-1>|any}] [ip-fragment {<0-1>|any}]]
[tcp-flag [tcp-fin {<0-1>|any}] [tcp-syn {<0-1>|any}]
[tcp-rst {<0-1>|any}] [tcp-psh {<0-1>|any}] [tcp-ack
{<0-1>|any}] [tcp-urg {<0-1>|any}]]| ipv6
[next-header {<0-5,7-16,18-57,59-255>|any}] [sip
{
{<0-1>|any}]| ipv6-icmp [sip {
[sip-bitmask
{<0-255>|any}] [icmp-code {<0-255>|any}]
[hop-limit {<0-1>|any}]| ipv6-udp [sip {
[sip-bitmask
<0-65535>]|any}] [dport {<0-65535> [to
<0-65535>]|any}] [hop-limit {<0-1>|any}]| ipv6-tcp
[sip {
{<0-65535> [to <0-65535>]|any}] [dport
{<0-65535> [to <0-65535>]|any}] [hop-limit
{<0-1>|any}] [tcp-flag [tcp-fin {<0-1>|any}] [tcp-syn
{<0-1>|any}] [tcp-rst {<0-1>|any}] [tcp-psh
{<0-1>|any}] [tcp-ack {<0-1>|any}] [tcp-urg
{<0-1>|any}]]} ] [action {permit|deny|filter
{switchport <1~53>|interface
[rate-limiter {<1-16>|disable}] [evc-policer
{<1-256>|disable}] [{redirect|port-copy} {switchport
{<1-53>|<1~53>}|interface
{
[disable]] [logging [disable]] [shutdown [disable]]
[lookup [disable]]
no access-list ace <1~256> Use the no access-list ace global
configuration command to delete the
access-list ace.
15 GLOBAL_CONFIG
show access-list [ interface [
[ rate-limiter [ <1~16> ] ] [ ace statistics
[ <1~256> ] ]
Use the show access-list privilege
EXEC command without keywords to
display the access-list configuration, or
particularly the show access-list
15 EXEC
interface for the access-list interface
configuration, or use the rate-limiter
keyword to display access-list
rate-limiter configuration, or use the ace
keyword to display access-list ace
configuration.
clear access-list ace statistics Use the clear access-list ace statistics
privileged EXEC command to clear the
statistics maintained by access-list,
including access-list interface statistics
and ACE's statistics.
15 EXEC
show access-list ace-status [ static ] [ link-oam ]
[ loop-protect ] [ dhcp ] [ ptp ] [ upnp ]
[ arp-inspection ] [ mep ] [ ipmc ] [ ip-source-guard ]
[ ip-mgmt ] [ conflicts ] [ switch
Use the show access-list ace-status
privilege EXEC command without
keywords to display the access-list ace
status for all access-list users, or
particularly the access-list user for the
access-list ace status. Use conflicts
keyword to display the access-list ace
that doesn't apply on on the hardware.
In other word, it means the specific ACE
is not applied to the hardware due to
hardware limitations.
15 EXEC
show aggregation [ mode ] 15 EXEC
aggregation mode { [ smac ] [ dmac ] [ ip ] [ port ] } 15 GLOBAL_CONFIG
no aggregation mode 15 GLOBAL_CONFIG
aggregation group
no aggregation group 15 INTERFACE_PORT_LIST
ip arp inspection Use the ip arp inspection global
configuration command to globally
enable ARP inspection. Use the no form
of this command to globally disable ARP
inspection.
13 GLOBAL_CONFIG
ip arp inspection vlan
configuration command to globally
enable ARP inspection. Use the no form
of this command to globally disable ARP
inspection.
13 GLOBAL_CONFIG
ip arp inspection vlan
permit | all }
no ip arp inspection vlan
ip arp inspection entry interface
13 GLOBAL_CONFIG
arp_inspection_translate 13 GLOBAL_CONFIG
arp_inspection_port_mode Use the ip arp inspection trust interface
configuration command to configure a
port as trusted for ARP inspection
purposes. Use the no form of this
command to configure a port as
untrusted.
13 INTERFACE_PORT_LIST
arp_inspection_port_check_vlan Use the ip arp inspection check-vlan
interface configuration command to
configure a port as VLAN mode for ARP
inspection purposes. Use the no form of
this command to configure a port as
default.
13 INTERFACE_PORT_LIST
ip arp inspection logging { deny | permit | all } Use the ip arp inspection logging
interface configuration command to
configure a port as some logging mode
for ARP inspection purposes. Use the
no form of this command to configure a
port as logging none.
13 INTERFACE_PORT_LIST
no ip arp inspection logging Use the no ip arp inspection logging
interface configuration command to
configure a port as default logging mode
for ARP inspection purposes.
13 INTERFACE_PORT_LIST
show ip arp inspection [ interface
vlan
0 EXEC
show ip arp inspection entry [ dhcp-snooping |
static ] [ interface
13 EXEC
aaa authentication login { console | telnet | ssh |
http } { [ local | radius | tacacs ] ... }
Use the aaa authentication login
command to configure the
authentication methods.
15 GLOBAL_CONFIG
no aaa authentication login { console | telnet | ssh |
http }
15 GLOBAL_CONFIG
radius-server timeout <1-1000> Use the radius-server timeout command
to configure the global RADIUS timeout
15 GLOBAL_CONFIG
value.
no radius-server timeout Use the no radius-server timeout
command to reset the global RADIUS
timeout value to default.
15 GLOBAL_CONFIG
radius-server retransmit <1-1000> Use the radius-server retransmit
command to configure the global
RADIUS retransmit value.
15 GLOBAL_CONFIG
no radius-server retransmit Use the no radius-server retransmit
command to reset the global RADIUS
retransmit value to default.
15 GLOBAL_CONFIG
radius-server deadtime <1-1440> Use the radius-server deadtime
command to configure the global
RADIUS deadtime value.
15 GLOBAL_CONFIG
no radius-server deadtime Use the no radius-server deadtime
command to reset the global RADIUS
deadtime value to default.
15 GLOBAL_CONFIG
radius-server key
configure the global RADIUS key.
15 GLOBAL_CONFIG
no radius-server key Use the no radius-server key command
to remove the global RADIUS key.
15 GLOBAL_CONFIG
radius-server attribute 4
no radius-server attribute 4 15 GLOBAL_CONFIG
radius-server attribute 95
no radius-server attribute 95 15 GLOBAL_CONFIG
radius-server attribute 32
no radius-server attribute 32 15 GLOBAL_CONFIG
radius-server host
<0-65535> ] [ acct-port <0-65535> ] [ timeout
<1-1000> ] [ retransmit <1-1000> ] [ key
Use the radius-server host command to
add a new RADIUS host.
15 GLOBAL_CONFIG
no radius-server host
<0-65535> ] [ acct-port <0-65535> ]
Use the no radius-server host command
to delete an existing RADIUS host.
15 GLOBAL_CONFIG
tacacs-server timeout <1-1000> Use the tacacs-server timeout
command to configure the global
TACACS+ timeout value.
15 GLOBAL_CONFIG
no tacacs-server timeout Use the no tacacs-server timeout
command to reset the global TACACS+
timeout value to default.
15 GLOBAL_CONFIG
tacacs-server deadtime <1-1440> Use the tacacs-server deadtime
command to configure the global
TACACS+ deadtime value.
15 GLOBAL_CONFIG
no tacacs-server deadtime Use the no tacacs-server deadtime
command to reset the global TACACS+
deadtime value to default.
15 GLOBAL_CONFIG
tacacs-server key
configure the global TACACS+ key.
15 GLOBAL_CONFIG
no tacacs-server key Use the no tacacs-server key command
to remove the global TACACS+ key.
15 GLOBAL_CONFIG
tacacs-server host
<0-65535> ] [ timeout <1-1000> ] [ key
Use the tacacs-server host command to
add a new TACACS+ host.
15 GLOBAL_CONFIG
no tacacs-server host
<0-65535> ]
Use the no tacacs-server host command
to delete an existing TACACS+ host.
15 GLOBAL_CONFIG
show aaa Use the show aaa command to view the
currently active authentication login
methods.
15 GLOBAL_CONFIG
show radius-server [ statistics ] Use the show radius-server command to
view the current RADIUS configuration
and statistics.
15 EXEC
show tacacs-server Use the show tacacs-server command
to view the current TACACS+
configuration.
15 EXEC
debug auth { console | telnet | ssh | http }
debug EXEC
clock summer-time
<1-7> <1-12>
13 GLOBAL_CONFIG
clock summer-time
<1-31> <2000-2097>
<2000-2097>
13 GLOBAL_CONFIG
no clock summer-time 13 GLOBAL_CONFIG
clock timezone
no clock timezone 13 GLOBAL_CONFIG
show clock detail 0 EXEC
clock summer-time
<1-7> <1-12>
13 GLOBAL_CONFIG
clock summer-time
<1-31> <2000-2097>
<2000-2097>
13 GLOBAL_CONFIG
no clock summer-time 13 GLOBAL_CONFIG
clock timezone
no clock timezone 13 GLOBAL_CONFIG
show clock detail 0 EXEC
show ip dhcp detailed statistics { server | client |
snooping | relay | normal-forward | combined }
[ interface
Use the show ip dhcp detailed statistics
user EXEC command to display
statistics. Notice that the normal forward
per-port TX statistics isn't increased if
the incoming DHCP packet is done by
L3 forwarding mechanism. Notice that
the normal forward per-port TX statistics
isn't increased if the incoming DHCP
packet is done by L3 forwarding
mechanism.
0 EXEC
clear ip dhcp detailed statistics { server | client |
snooping | relay | helper | all } [ interface
Use the clear ip dhcp detailed statistics
privileged EXEC command to clear the
statistics, or particularly the IP DHCP
statistics for the interface. Notice that
except for clear statistics on all
interfaces, clear the statistics on specific
port may not take effect on global
statistics since it gathers the different
layer overview.
15 EXEC
clear ip dhcp relay statistics Use the clear ip dhcp relay statistics
privileged EXEC command to clear the
statistics maintained by IP DHCP realy.
15 EXEC
show ip dhcp relay [ statistics ] Use the show ip dhcp relay user EXEC
command without keywords to display
the DHCP relay configuration, or use the
statistics keyword to display statistics.
0 EXEC
ip dhcp relay Use the ip dhcp relay global
configuration command to enable the
DHCP relay server. Use the no form of
thiscommand to disable the DHCP
relay server.
15 GLOBAL_CONFIG
ip helper-address
configuration command to configure the
host address of DHCP relay server.
15 GLOBAL_CONFIG
no ip helper-address Use the no ip helper-address global
configuration command to clear the host
address of DHCP relay server.
15 GLOBAL_CONFIG
ip dhcp relay information option Use the ip dhcp relay information option
global configuration command to enable
the DHCP relay information option. Use
the no form of this command to disable
the DHCP relay information option. The
option 82 circuit ID format as
"[vlan_id][module_id][port_no]". The first
four characters represent the VLAN ID,
the fifth and sixth characters are the
module ID(in standalone device it
always equal 0), and the last two
characters are the port number. For
example, "00030108" means the DHCP
message receive form VLAN ID 3,
switch ID 1, port No 8. And the option 82
remote ID value is equal the switch MAC
address.
15 GLOBAL_CONFIG
ip dhcp relay information policy { drop | keep |
replace }
Use the ip dhcp relay information policy
global configuration command to
configure the DHCP relay information
policy. When DHCP relay information
mode operation is enabled, if the agent
receives a DHCP message that already
contains relay agent information it will
enforce the policy. The 'Replace' policy
is invalid when relay information mode is
disabled.
15 GLOBAL_CONFIG
no ip dhcp relay information policy Use the ip dhcp relay information policy
global configuration command to restore
the default DHCP relay information
policy.
15 GLOBAL_CONFIG
show ip dhcp pool [
show ip dhcp pool counter [
show ip dhcp excluded-address 0 EXEC
show ip dhcp server binding [ state {allocated |
committed | expired} ] [ type {automatic | manual |
expired} ]
0 EXEC
show ip dhcp server binding
show ip dhcp server 0 EXEC
show ip dhcp server statistics 0 EXEC
show ip dhcp server declined-ip 0 EXEC
show ip dhcp server declined-ip
clear ip dhcp server binding
clear ip dhcp server binding { automatic | manual |
expired }
13 EXEC
clear ip dhcp server statistics 13 EXEC
ip dhcp server 13 GLOBAL_CONFIG
ip dhcp excluded-address
[
13 GLOBAL_CONFIG
no ip dhcp pool
ip dhcp server 13 INTERFACE_VLAN
network
no network 13 DHCP_POOL
broadcast
no broadcast 13 DHCP_POOL
default-router
[
13 DHCP_POOL
no default-router 13 DHCP_POOL
lease { <0-365> [ <0-23> [
no lease 13 DHCP_POOL
domain-name
no domain-name 13 DHCP_POOL
dns-server
[
13 DHCP_POOL
no dns-server 13 DHCP_POOL
ntp-server
[
13 DHCP_POOL
no ntp-server 13 DHCP_POOL
netbios-name-server
[
no netbios-name-server 13 DHCP_POOL
netbios-node-type { b-node | h-node | m-node |
p-node }
13 DHCP_POOL
no netbios-node-type 13 DHCP_POOL
netbios-scope
no netbios-scope 13 DHCP_POOL
nis-domain-name
no nis-domain-name 13 DHCP_POOL
nis-server
[
13 DHCP_POOL
no nis-server 13 DHCP_POOL
host
no host 13 DHCP_POOL
client-identifier { fqdn
13 DHCP_POOL
no client-identifier 13 DHCP_POOL
hardware-address
no hardware-address 13 DHCP_POOL
client-name
no client-name 13 DHCP_POOL
vendor class-identifier
13 DHCP_POOL
no vendor class-identifier
debug dhcp server memsize debug EXEC
debug dhcp server declined add
debug dhcp server declined delete
show ip dhcp snooping [ interface
Use the show ip dhcp snooping user
EXEC command to display the DHCP
snooping configuration.
0 EXEC
show ip dhcp snooping [ statistics ] [ interface
Use the show ip dhcp snooping user
EXEC command without keywords to
display the DHCP snooping
configuration, or particularly the ip dhcp
snooping statistics for the interface, or
use the statistics keyword to display
statistics.
0 EXEC
clear ip dhcp snooping statistics [ interface Use the clear ip dhcp snooping statistics 15 EXEC
statistics maintained by IP DHCP
snooping, or particularly the IP DHCP
snooping statistics for the interface.
ip dhcp snooping Use the ip dhcp snooping global
configuration command to globally
enable DHCP snooping. Use the no
form of this command to globally disable
DHCP snooping.
15 GLOBAL_CONFIG
dhcp_snooping_port_mode Use the ip dhcp snooping trust interface
configuration command to configure a
port as trusted for DHCP snooping
purposes. Use the no form of this
command to configure a port as
untrusted.
15 INTERFACE_PORT_LIST
show ip dhcp snooping table Use the show ip dhcp snooping table
user EXEC command to display the IP
assigned information that is obtained
from DHCP server except for local
VLAN interface IP addresses.
15 EXEC
ip name-server {
vlan
Set the DNS server for resolving domain
names
15 GLOBAL_CONFIG
no ip name-server Stop resolving domain names by
accessing DNS server
15 GLOBAL_CONFIG
show ip name-server Display the active domain name server
information
0 EXEC
ip dns proxy Enable DNS proxy service 15 GLOBAL_CONFIG
show version Use show version to display firmware
information.
0 EXEC
firmware upgrade
firmware image to the switch.
15 EXEC
firmware swap Use firmware swap to swap the active
and alternative firmware images.
15 EXEC
show green-ethernet fan Shows Fan status (chip Temperature
and fan speed).
15 GLOBAL_CONFIG
green-ethernet fan temp-on <-127-127> Sets temperature at which to turn fan on
to the lowest speed.
15 GLOBAL_CONFIG
no green-ethernet fan temp-on Sets temperature at which to turn fan on 15 GLOBAL_CONFIG
to the lowest speed to default.
green-ethernet fan temp-max <-127-127> Sets temperature where the fan must be
running at full speed.
15 GLOBAL_CONFIG
no green-ethernet fan temp-max Sets temperature at which the fan shall
be running at full speed to default.
15 GLOBAL_CONFIG
green-ethernet led interval <0~24> intensity
<0-100>
Use green-ethernet led interval to
configure the LED intensity at specific
interval of the day.
15 GLOBAL_CONFIG
no green-ethernet led interval <0~24> 15 GLOBAL_CONFIG
green-ethernet led on-event { [ link-change
<0-65535> ] [ error ] }*1
Use green-ethernet led on-event to
configure when to turn LEDs intensity to
100%%.
15 GLOBAL_CONFIG
no green-ethernet led on-event [ link-change ]
[ error ]
15 GLOBAL_CONFIG
show green-ethernet eee [interface
Shows Green Ethernet EEE status. 15 EXEC
show green-ethernet short-reach [interface
Shows Green Ethernet short-reach
status.
15 EXEC
show green-ethernet energy-detect [interface
Shows Green Ethernet energy-detect
status.
15 EXEC
show green-ethernet [interface
green-ethernet eee Sets EEE mode. 15 INTERFACE_PORT_LIST
green-ethernet eee urgent-queues [
green-ethernet eee optimize-for-power Sets if EEE should be optimized for
least traffic latency or least power
comsumption
15 GLOBAL_CONFIG
green-ethernet energy-detect Enables energy-detect power savings. 15 INTERFACE_PORT_LIST
green-ethernet short-reach Enables short-reach power savings. 15 INTERFACE_PORT_LIST
show ip http server secure status Use the show ip http server secure
status privileged EXEC command to
display the secure HTTP web server
status.
15 EXEC
ip http secure-server Use the ip http secure-server global
configuration command to enable the
secure HTTP web server. Use the no
form of this command to disable the
secure HTTP web server.
15 GLOBAL_CONFIG
ip http secure-redirect Use the http secure-redirect global 15 GLOBAL_CONFIG
configuration command to enable the
secure HTTP web redirection. When the
secure HTTP web server is enabled, the
feature automatic redirect the none
secure HTTP web connection to the
secure HTTP web connection. Use the
no form of this command to disable the
secure HTTP web redirection.
reload { { { cold | warm } [ sid <1-16> ] } | { defaults
[ keep-ip ] } }
Reload system, either cold (reboot) or
restore defaults without reboot.
15 EXEC
show running-config [ all-defaults ] 15 EXEC
show running-config feature
[ all-defaults ]
15 EXEC
show running-config interface
[ all-defaults ]
15 EXEC
show running-config interface vlan
[ all-defaults ]
15 EXEC
show running-config vlan
show running-config line { console | vty }
15 EXEC
copy { startup-config | running-config |
{ startup-config | running-config |
[ syntax-check ]
15 EXEC
dir 15 EXEC
more
delete
debug icfg wipe-flash-fs-conf-block debug EXEC
debug icfg wipe-specific-block {local|global}
debug icfg silent-upgrade status debug EXEC
debug icfg dir debug EXEC
debug icfg error-trace
ip routing Enable routing for IPv4 and IPv6 15 GLOBAL_CONFIG
no ip routing Disable routing for IPv4 and IPv6 15 GLOBAL_CONFIG
ip address {{
[fallback
IP address configuration 15 INTERFACE_VLAN
ip dhcp retry interface vlan
no ip address IP address configuration 15 INTERFACE_VLAN
ip route
Add new IP route 15 GLOBAL_CONFIG
no ip route
Delete an existing IP route 15 GLOBAL_CONFIG
show interface vlan [
show ip interface brief Brief IP interface status 0 EXEC
show ip arp Print ARP table 0 EXEC
clear ip arp Clear ARP cache 0 EXEC
show ip route Routing table status 0 EXEC
ping ip
<2-1452> ] [ interval <0-30> ]
0 EXEC
clear ip statistics [ system ] [ interface vlan
0 EXEC
show ip statistics [ system ] [ interface vlan
0 EXEC
debug ipstack log [ERR|NOERR]
[WARNING|NOWARNING] [NOTICE|NONOTICE]
[INFO|NOINFO] [DEBUG|NODEBUG]
[MDEBUG|NOMDEBUG] [IOCTL|NOIOCTL]
[INIT|NOINIT] [ADDR|NOADDR] [FAIL|NOFAIL]
[EMERG|NOEMERG] [CRIT|NOCRIT]
debug EXEC
debug ip kmem debug EXEC
debug ip route debug EXEC
debug ip sockets debug EXEC
debug ip lpm stat ip
debug ip lpm stat ipv6
debug ip lpm stat clear
debug ip lpm sticky clear debug EXEC
debug ip lpm usage debug EXEC
debug ip global interface table change debug EXEC
debug ip vlan ipv4 created
debug ip vlan ipv4 changed
debug ip vlan ipv6 created
debug ip vlan ipv6 changed
show ip igmp snooping mrouter [ detail ] 0 EXEC
clear ip igmp snooping [ vlan
show ip igmp snooping [ vlan
[ group-database [ interface
[ sfm-information ] ] [ detail ]
ip igmp snooping 15 GLOBAL_CONFIG
ip igmp unknown-flooding 15 GLOBAL_CONFIG
ip igmp host-proxy [ leave-proxy ] 15 GLOBAL_CONFIG
ip igmp ssm-range
no ip igmp ssm-range 15 GLOBAL_CONFIG
ip igmp snooping vlan
no ip igmp snooping vlan [
ip igmp snooping 15 INTERFACE_VLAN
ip igmp snooping querier { election | address
15 INTERFACE_VLAN
no ip igmp snooping querier { election | address } 15 INTERFACE_VLAN
ip igmp snooping compatibility { auto | v1 | v2 | v3 } 15 INTERFACE_VLAN
no ip igmp snooping compatibility 15 INTERFACE_VLAN
ip igmp snooping priority <0-7> 15 INTERFACE_VLAN
no ip igmp snooping priority 15 INTERFACE_VLAN
ip igmp snooping robustness-variable <1-255> 15 INTERFACE_VLAN
no ip igmp snooping robustness-variable 15 INTERFACE_VLAN
ip igmp snooping query-interval <1-31744> 15 INTERFACE_VLAN
no ip igmp snooping query-interval 15 INTERFACE_VLAN
ip igmp snooping query-max-response-time
<0-31744>
15 INTERFACE_VLAN
no ip igmp snooping query-max-response-time 15 INTERFACE_VLAN
ip igmp snooping last-member-query-interval
<0-31744>
15 INTERFACE_VLAN
no ip igmp snooping last-member-query-interval 15 INTERFACE_VLAN
ip igmp snooping unsolicited-report-interval
<0-31744>
15 INTERFACE_VLAN
no ip igmp snooping unsolicited-report-interval 15 INTERFACE_VLAN
ip igmp snooping immediate-leave 15 INTERFACE_VLAN
ip igmp snooping mrouter 15 INTERFACE_PORT_LIST
ip igmp snooping max-groups <1-10> 15 INTERFACE_PORT_LIST
no ip igmp snooping max-groups 15 INTERFACE_PORT_LIST
ip igmp snooping filter
no ip igmp snooping filter 15 INTERFACE_PORT_LIST
ipv6 mld snooping 15 GLOBAL_CONFIG
ipv6 mld unknown-flooding 15 GLOBAL_CONFIG
ipv6 mld host-proxy [ leave-proxy ] 15 GLOBAL_CONFIG
ipv6 mld ssm-range
no ipv6 mld ssm-range 15 GLOBAL_CONFIG
ipv6 mld snooping vlan
no ipv6 mld snooping vlan [
ipv6 mld snooping immediate-leave 15 INTERFACE_PORT_LIST
ipv6 mld snooping mrouter 15 INTERFACE_PORT_LIST
ipv6 mld snooping max-groups <1-10> 15 INTERFACE_PORT_LIST
no ipv6 mld snooping max-groups 15 INTERFACE_PORT_LIST
ipv6 mld snooping filter
no ipv6 mld snooping filter 15 INTERFACE_PORT_LIST
show ipv6 mld snooping mrouter [ detail ] 0 EXEC
clear ipv6 mld snooping [ vlan
statistics
15 EXEC
show ipv6 mld snooping [ vlan
[ group-database [ interface
[ sfm-information ] ] [ detail ]
0 EXEC
ipv6 mld snooping 15 INTERFACE_VLAN
ipv6 mld snooping querier election 15 INTERFACE_VLAN
ipv6 mld snooping compatibility { auto | v1 | v2 } 15 INTERFACE_VLAN
no ipv6 mld snooping compatibility 15 INTERFACE_VLAN
ipv6 mld snooping priority <0-7> 15 INTERFACE_VLAN
no ipv6 mld snooping priority 15 INTERFACE_VLAN
ipv6 mld snooping robustness-variable <1-255> 15 INTERFACE_VLAN
no ipv6 mld snooping robustness-variable 15 INTERFACE_VLAN
ipv6 mld snooping query-interval <1-31744> 15 INTERFACE_VLAN
no ipv6 mld snooping query-interval 15 INTERFACE_VLAN
ipv6 mld snooping query-max-response-time
<0-31744>
15 INTERFACE_VLAN
no ipv6 mld snooping query-max-response-time 15 INTERFACE_VLAN
ipv6 mld snooping last-member-query-interval
<0-31744>
15 INTERFACE_VLAN
no ipv6 mld snooping last-member-query-interval 15 INTERFACE_VLAN
ipv6 mld snooping unsolicited-report-interval
<0-31744>
15 INTERFACE_VLAN
no ipv6 mld snooping unsolicited-report-interval 15 INTERFACE_VLAN
ip verify source 13 GLOBAL_CONFIG
i ip verify source 13 INTERFACE_PORT_LIST
ip verify source limit <0-2> 13 INTERFACE_PORT_LIST
no ip verify source limit 13 INTERFACE_PORT_LIST
ip verify source translate 13 GLOBAL_CONFIG
show ip verify source [interface
show ip source binding [ dhcp-snooping | static ]
[interface
13 EXEC
ip source binding interface
13 GLOBAL_CONFIG
ip source binding interface
13 GLOBAL_CONFIG
show lacp { internal | statistics | system-id |
neighbour }
Show LACP configuration and status 15 EXEC
clear lacp statistics Clear all LACP statistics 15 EXEC
lacp system-priority <1-65535> Set the LACP system priority 15 GLOBAL_CONFIG
lacp Enable LACP on an interface 15 INTERFACE_PORT_LIST
lacp key { <1-65535> | auto } Set the LACP key 15 INTERFACE_PORT_LIST
lacp role { active | passive } Set the LACP role, active or passive in
transmitting BPDUs
15 INTERFACE_PORT_LIST
lacp timeout { fast | slow } Set the LACP timeout, i.e. how fast to
transmit BPDUs, once a sec or once
each 30 sec.
15 INTERFACE_PORT_LIST
lacp port-priority <1-65535> Set the lacp port priority, 15 INTERFACE_PORT_LIST
lldp holdtime <2-10> Sets LLDP hold time (The neighbor
switch will discarded the LLDP
information after \"hold time\" multiplied
with \"timer\" seconds )
15 GLOBAL_CONFIG
no lldp holdtime 15 GLOBAL_CONFIG
lldp timer <5-32768> Sets LLDP TX interval (The time
between each LLDP frame transmitted
in seconds).
15 GLOBAL_CONFIG
no lldp timer 15 GLOBAL_CONFIG
lldp reinit <1-10> Sets LLDP reinitialization delay. 15 GLOBAL_CONFIG
no lldp reinit Sets LLDP reinitialization delay. 15 GLOBAL_CONFIG
lldp tlv-select {management-address |
port-description | system-capabilities |
system-description | system-name}
Enables/disables LLDP optional TLVs. 15 INTERFACE_PORT_LIST
lldp transmit Sets if switch shall transmit LLDP
frames.
15 INTERFACE_PORT_LIST
lldp receive Sets if switch shall update LLDP entry
table with incoming LLDP information.
15 INTERFACE_PORT_LIST
show lldp neighbors [ interface
show lldp statistics [ interface
clear lldp statistics Clears the LLDP statistics. 0 EXEC
lldp transmission-delay <1-8192> Sets LLDP transmision-delay. LLDP
transmission delay (the amount of time
that the transmission of LLDP frames
will delayed after LLDP configuration
has changed) in seconds.)
15 GLOBAL_CONFIG
no lldp transmission-delay 15 GLOBAL_CONFIG
lldp cdp-aware Configures if the interface shall be CDP
aware (CDP discovery information is
added to the LLDP neighbor table)
15 INTERFACE_PORT_LIST
show lldp med remote-device [ interface
Show LLDP-MED neighbor device
information.
0 EXEC
show lldp med media-vlan-policy [<0~31>] Show media vlan policy(ies) 0 EXEC
lldp med location-tlv latitude { north | south }
Use the lldp med location-tlv latitude to
configure the location latitude.
15 GLOBAL_CONFIG
no lldp med location-tlv latitude Use no lldp med location-tlv latitude to
configure the latitude location to north 0
degrees.
15 GLOBAL_CONFIG
lldp med location-tlv longitude { west | east }
Use the lldp med location-tlv longitude
to configure the location longitude.
15 GLOBAL_CONFIG
no lldp med location-tlv longitude Use no lldp med location-tlv longitude to
configure the longitude location to north
0 degrees.
15 GLOBAL_CONFIG
lldp med location-tlv altitude { meters | floors }
Use the lldp med location-tlv altitude to
configure the location altitude.
15 GLOBAL_CONFIG
no lldp med location-tlv altitude Use the lldp med location-tlv altitude to
configure the location altitude.
15 GLOBAL_CONFIG
lldp med location-tlv civic-addr { country | state |
county | city | district | block | street |
leading-street-direction | trailing-street-suffix |
street-suffix | house-no | house-no-suffix |
landmark | additional-info | name | zip-code |
Use lldp med location-tlv civic-addr to
configure the civic address.
15 GLOBAL_CONFIG
building | apartment | floor | room-number |
place-type | postal-community-name | p-o-box |
additional-code }
no lldp med location-tlv civic-addr { country | state |
county | city | district | block | street |
leading-street-direction | trailing-street-suffix |
street-suffix | house-no | house-no-suffix |
landmark | additional-info | name | zip-code |
building | apartment | floor | room-number |
place-type | postal-community-name | p-o-box |
additional-code }
15 GLOBAL_CONFIG
lldp med location-tlv elin-addr
configure value for the Emergency Call
Service
15 GLOBAL_CONFIG
no lldp med location-tlv elin-addr Use the no lldp med location-tlv
elin-addr to configure value for the
Emergency Call Service to default
value.
15 GLOBAL_CONFIG
lldp med transmit-tlv [ capabilities ] [ location ]
[ network-policy ]
Use the lldp med transmit-tlv to
configure which TLVs to transmit to link
partner.
15 INTERFACE_PORT_LIST
no lldp med transmit-tlv [ capabilities ] [ location ]
[ network-policy ]
15 INTERFACE_PORT_LIST
lldp med datum { wgs84 | nad83-navd88 |
nad83-mllw }
Use the lldp med datum to configure the
datum (geodetic system) to use.
15 GLOBAL_CONFIG
no lldp med datum 15 GLOBAL_CONFIG
lldp med fast <1-10> Use the lldp med fast to configure the
number of times the fast start LLDPDU
are being sent during the activation of
the fast start mechanism defined by
LLDP-MED (1-10).
15 GLOBAL_CONFIG
no lldp med fast 15 GLOBAL_CONFIG
lldp med media-vlan-policy <0-31> { voice |
voice-signaling | guest-voice-signaling |
guest-voice | softphone-voice | video-conferencing
| streaming-video | video-signaling } { tagged
<0-63>]
Use the media-vlan-policy to create a
policy, which can be assigned to an
interface.
15 GLOBAL_CONFIG
no lldp med media-vlan-policy <0~31> 15 GLOBAL_CONFIG
lldp med media-vlan policy-list
policy to the interface.
15 INTERFACE_PORT_LIST
loop-protect Loop protection configuration 15 GLOBAL_CONFIG
loop-protect transmit-time <1-10> Loop protection transmit time interval 15 GLOBAL_CONFIG
no loop-protect transmit-time 15 GLOBAL_CONFIG
loop-protect shutdown-time <0-604800> Loop protection shutdown time interval 15 GLOBAL_CONFIG
no loop-protect shutdown-time 15 GLOBAL_CONFIG
loop-protect Loop protection configuration 15 INTERFACE_PORT_LIST
loop-protect action { [shutdown] [log] }*1 15 INTERFACE_PORT_LIST
no loop-protect action 15 INTERFACE_PORT_LIST
loop-protect tx-mode 15 INTERFACE_PORT_LIST
show loop-protect [ interface
mac address-table learning [secure] Enable learning on port 15 INTERFACE_PORT_LIST
show mac address-table [ conf | static | aging-time
| { { learning | count } [ interface
| { address
0 EXEC
clear mac address-table 15 EXEC
mac address-table static
Assign a static mac address to this port 15 GLOBAL_CONFIG
mac address-table aging-time <0,10-1000000> Set switch aging time, 0 to disable. 15 GLOBAL_CONFIG
no mac address-table aging-time Default aging time. 15 GLOBAL_CONFIG
monitor destination interface
no monitor destination Sets monitor destination port. 15 GLOBAL_CONFIG
monitor source { { interface
{ cpu [
Sets monitor source port(s). 15 GLOBAL_CONFIG
no monitor source { { interface
{ cpu [
Sets monitor source port(s). 15 GLOBAL_CONFIG
debug chip [ { 0 | 1 | all } ] debug EXEC
debug api [ interface
[ { init | misc | port | counters | phy | vlan | pvlan |
mac-table | acl | qos | aggr | stp | mirror | evc | erps
| eps | packet | fdma | ts | pts | wm | ipmc | cmef |
mplscore | mplsoam | vxlat | oam | sgpio | l3 | afi |
macsec } ] [ full ] [ clear ]
debug EXEC
debug suspend debug EXEC
debug resume debug EXEC
debug kr-conf [ cm1 <-32-31> ] [ c0 <-32-31> ]
[ cp1 <-32-31> ] [ ampl <300-1275> ] [ { ps25 |
ps35 | ps55 | ps70 | ps120 } ] [ en-ob | dis-ob ]
[ ser-inv | ser-no-inv ]
debug INTERFACE_PORT_LIST
show spanning-tree [ summary | active | { interface
[ interface
15 EXEC
clear spanning-tree { { statistics [ interface
[ interface
15 EXEC
spanning-tree mode { stp | rstp | mstp } 15 GLOBAL_CONFIG
no spanning-tree mode 15 GLOBAL_CONFIG
spanning-tree transmit hold-count <1-10> 15 GLOBAL_CONFIG
no spanning-tree transmit hold-count 15 GLOBAL_CONFIG
spanning-tree mst max-hops <6-40> 15 GLOBAL_CONFIG
no spanning-tree mst max-hops 15 GLOBAL_CONFIG
spanning-tree mst max-age <6-40> [ forward-time
<4-30> ]
15 GLOBAL_CONFIG
no spanning-tree mst max-age 15 GLOBAL_CONFIG
spanning-tree mst forward-time <4-30> 15 GLOBAL_CONFIG
no spanning-tree mst forward-time 15 GLOBAL_CONFIG
spanning-tree edge bpdu-filter 15 GLOBAL_CONFIG
spanning-tree edge bpdu-guard 15 GLOBAL_CONFIG
spanning-tree recovery interval <30-86400> 15 GLOBAL_CONFIG
no spanning-tree recovery interval 15 GLOBAL_CONFIG
spanning-tree mst <0-7> priority <0-61440> 15 GLOBAL_CONFIG
no spanning-tree mst <0-7> priority 15 GLOBAL_CONFIG
spanning-tree mst <0-7> vlan
no spanning-tree mst <0-7> vlan 15 GLOBAL_CONFIG
spanning-tree mst name
<0-65535>
15 GLOBAL_CONFIG
no spanning-tree mst name 15 GLOBAL_CONFIG
spanning-tree 15 INTERFACE_PORT_LIST
spanning-tree edge 15 INTERFACE_PORT_LIST
spanning-tree auto-edge 15 INTERFACE_PORT_LIST
spanning-tree link-type { point-to-point | shared | 15 INTERFACE_PORT_LIST
auto }
no spanning-tree link-type 15 INTERFACE_PORT_LIST
spanning-tree restricted-role 15 INTERFACE_PORT_LIST
spanning-tree restricted-tcn 15 INTERFACE_PORT_LIST
spanning-tree bpdu-guard 15 INTERFACE_PORT_LIST
spanning-tree mst <0-7> cost { <1-200000000> |
auto }
15 INTERFACE_PORT_LIST
no spanning-tree mst <0-7> cost 15 INTERFACE_PORT_LIST
spanning-tree mst <0-7> port-priority <0-240> 15 INTERFACE_PORT_LIST
no spanning-tree mst <0-7> port-priority 15 INTERFACE_PORT_LIST
spanning-tree 15 STP_AGGR
spanning-tree edge 15 STP_AGGR
spanning-tree auto-edge 15 STP_AGGR
spanning-tree link-type { point-to-point | shared |
auto }
15 STP_AGGR
no spanning-tree link-type 15 STP_AGGR
spanning-tree restricted-role 15 STP_AGGR
spanning-tree restricted-tcn 15 STP_AGGR
spanning-tree bpdu-guard 15 STP_AGGR
spanning-tree mst <0-7> cost { <1-200000000> |
auto }
15 STP_AGGR
no spanning-tree mst <0-7> cost 15 STP_AGGR
spanning-tree mst <0-7> port-priority <0-240> 15 STP_AGGR
no spanning-tree mst <0-7> port-priority 15 STP_AGGR
mvr vlan
mvr name
no mvr vlan
no mvr name
mvr immediate-leave 15 INTERFACE_PORT_LIST
clear mvr [ vlan
statistics
15 EXEC
show mvr [ vlan
[ group-database [ interface
[ sfm-information ] ] [ detail ]
0 EXEC
mvr 15 GLOBAL_CONFIG
mvr vlan
no mvr vlan
mvr vlan
mvr name
compatible }
15 GLOBAL_CONFIG
no mvr vlan
no mvr name
mvr vlan
mvr name
no mvr vlan
no mvr name
mvr vlan
mvr vlan
mvr name
mvr name
no mvr vlan
no mvr name
mvr vlan
<0-31744>
15 GLOBAL_CONFIG
mvr name
<0-31744>
15 GLOBAL_CONFIG
no mvr vlan
last-member-query-interval
15 GLOBAL_CONFIG
no mvr name
last-member-query-interval
15 GLOBAL_CONFIG
mvr vlan
no mvr vlan
no mvr name
show dot1x statistics { eapol | radius | all}
[ interface
Shows statistics for either eapol or
radius.
0 EXEC
show dot1x status [ interface
[brief]
Shows dot1x status, such as admin
state, port state and last source.
0 EXEC
clear dot1x statistics [ interface
dot1x re-authentication Set Re-authentication state 15 GLOBAL_CONFIG
dot1x authentication timer re-authenticate
<1-3600>
The period between re-authentication
attempts in seconds
15 GLOBAL_CONFIG
no dot1x authentication timer re-authenticate 15 GLOBAL_CONFIG
dot1x timeout tx-period <1-65535> the time between EAPOL
retransmissions.
15 GLOBAL_CONFIG
no dot1x timeout tx-period 15 GLOBAL_CONFIG
dot1x authentication timer inactivity <10-1000000> Time in seconds between check for
activity on successfully authenticated
MAC addresses.
15 GLOBAL_CONFIG
no dot1x authentication timer inactivity 15 GLOBAL_CONFIG
dot1x timeout quiet-period <10-1000000> Time in seconds before a MAC-address
that failed authentication gets a new
authentication chance.
15 GLOBAL_CONFIG
no dot1x timeout quiet-period 15 GLOBAL_CONFIG
dot1x re-authenticate Refresh (restart) 802.1X authentication
process.
15 INTERFACE_PORT_LIST
dot1x initialize [ interface
dot1x system-auth-control Set the global NAS state 15 GLOBAL_CONFIG
dot1x port-control { force-authorized |
force-unauthorized | auto | single | multi |
mac-based }
Sets the port security state. 15 INTERFACE_PORT_LIST
no dot1x port-control Sets the port security state. 15 INTERFACE_PORT_LIST
dot1x guest-vlan Enables/disables guest VLAN 15 INTERFACE_PORT_LIST
dot1x max-reauth-req <1-255> The number of times a Request Identity
EAPOL frame is sent without response
before considering entering the Guest
VLAN
15 GLOBAL_CONFIG
no dot1x max-reauth-req The number of times a Request Identity
EAPOL frame is sent without response
before considering entering the Guest
VLAN
15 GLOBAL_CONFIG
dot1x guest-vlan <1-4095> Guest VLAN ID used when entering the
Guest VLAN.
15 GLOBAL_CONFIG
no dot1x guest-vlan Guest VLAN ID used when entering the
Guest VLAN.
15 GLOBAL_CONFIG
dot1x guest-vlan supplicant The switch remembers if an EAPOL
frame has been received on the port for
the life-time of the port. Once the switch
considers whether to enter the Guest
VLAN, it will first check if this option is
enabled or disabled. If disabled
(unchecked; default), the switch will only
enter the Guest VLAN if an EAPOL
15 GLOBAL_CONFIG
frame has not been received on the port
for the life-time of the port. If enabled
(checked), the switch will consider
entering the Guest VLAN even if an
EAPOL frame has been received on the
port for the life-time of the port.
dot1x radius-qos Enables/disables per-port state of
RADIUS-assigned QoS.
15 INTERFACE_PORT_LIST
dot1x radius-vlan Enables/disables per-port state of
RADIUS-assigned VLAN.
15 INTERFACE_PORT_LIST
dot1x feature { [ guest-vlan ] [ radius-qos ]
[ radius-vlan ] }*1
Globally enables/disables a dot1x
feature functionality
15 GLOBAL_CONFIG
show dot1x statistics { eapol | radius | all}
[ interface
Shows statistics for either eapol or
radius.
0 EXEC
ntp Enable NTP 13 GLOBAL_CONFIG
ntp server <1-5> ip-address
{
13 GLOBAL_CONFIG
ntp server <1-5> ip-address
{
13 GLOBAL_CONFIG
no_ntp_server_ip_address 13 GLOBAL_CONFIG
show ntp status 13 EXEC
show platform phy [ interface
or a given interface
15 EXEC
show platform phy id [ interface
show platform phy instance 15 EXEC
show platform phy failover 15 EXEC
platform phy instance restart { cool | warm } 15 EXEC
platform phy instance default-activate 15 EXEC
show platform phy status [interface
15 EXEC
no platform phy instance 15 GLOBAL_CONFIG
platform phy failover 15 INTERFACE_PORT_LIST
debug phy read [ <0~31> ] [ <0-0xffff> ]
[ addr-sort ]
debug INTERFACE_PORT_LIST
debug phy write [ <0~31> ] <0-0xffff> [ <0-0xffff> ] debug INTERFACE_PORT_LIST
debug phy do-page-chk [enable|disable] debug EXEC
debug phy force-pass-through-speed {1G | 100M |
10M}
debug INTERFACE_PORT_LIST
debug phy reset debug INTERFACE_PORT_LIST
debug phy gpio <0-13> mode
{output|input|alternative}
debug INTERFACE_PORT_LIST
debug phy gpio <0-13> get debug INTERFACE_PORT_LIST
show poe [ interface
poe mode { standard | plus } Use poe mode to configure of PoE
mode.
15 INTERFACE_PORT_LIST
no poe mode Use poe mode to configure of PoE
mode.
15 INTERFACE_PORT_LIST
poe priority { low | high | critical } Use poe priority to configure PoE
priority.
15 INTERFACE_PORT_LIST
no poe priority Use poe priority to configure PoE
priority.
15 INTERFACE_PORT_LIST
poe management mode { class-consumption |
class-reserved-power | allocation-consumption |
allocation-reserved-power | lldp-consumption |
lldp-reserved-power }
Use management mode to configure
PoE power management method.
15 GLOBAL_CONFIG
no poe management mode 15 GLOBAL_CONFIG
poe power limit {
maximum allowed power for the
interface when power management is in
allocation mode.
15 INTERFACE_PORT_LIST
no poe power limit Use poe power limit to configure the
maximum allowed power for the
interface when power management is in
allocation mode.
15 INTERFACE_PORT_LIST
poe supply sid <1~16> <1-2000> Use poe supply to specify the maximum
power the power supply can deliver.
15 GLOBAL_CONFIG
no poe supply [sid <1~16>] 15 GLOBAL_CONFIG
poe schedule-mode Configure PoE Schedule mode. 15 INTERFACE_PORT_LIST
no poe schedule-mode disable PoE power management
method.
15 INTERFACE_PORT_LIST
poe select-all
no poe schedule-all
method.
15 GLOBAL_CONFIG
poe delay-mode
no poe delay-mode
poe delay-time
poe hour <0-23> This command is used to set hour time
per week to enable PoE.
15 INTERFACE_PORT_LIST
no poe hour <0-23> This command is used to set hour time
per week to disable PoE.
15 INTERFACE_PORT_LIST
poe Sun This command is used to set hour time
on Sunday to enable PoE.
15 INTERFACE_PORT_LIST
no poe Sun This command is used to set hour time
on Sunday to disble PoE.
15 INTERFACE_PORT_LIST
poe Mon This command is used to set hour time
on Monday to enable PoE.
15 INTERFACE_PORT_LIST
no poe Mon This command is used to set hour time
on Monday to disable PoE.
15 INTERFACE_PORT_LIST
poe Tue This command is used to set hour time
on Tuesday to enable PoE.
15 INTERFACE_PORT_LIST
no poe Tue This command is used to set hour time
on Tuesday to disable PoE.
15 INTERFACE_PORT_LIST
poe Wed This command is used to set hour time
on Wednesday to enable PoE.
15 INTERFACE_PORT_LIST
no poe Wed This command is used to set hour time
on Wednesday to disable PoE.
15 INTERFACE_PORT_LIST
poe Thr This command is used to set hour time
on Thursday to enable PoE.
15 INTERFACE_PORT_LIST
no poe Thr This command is used to set hour time
on Thursday to enable PoE.
15 INTERFACE_PORT_LIST
poe Fri This command is used to set hour time
on Friday to enable PoE.
15 INTERFACE_PORT_LIST
no poe Fri This command is used to set hour time
on Friday to disable PoE.
15 INTERFACE_PORT_LIST
poe Sat This command is used to set hour time
on Saturday to enable PoE.
15 INTERFACE_PORT_LIST
no poe Sat This command is used to set hour time
on Saturday to disable PoE.
15 INTERFACE_PORT_LIST
show interface
[ { packets | bytes | errors | discards | filtered |
{ priority [<0~7>] } } ] [ { up | down } ]
Shows the statistics for the interface. 0 EXEC
show interface
clear statistics [interface]
show interface
show interface
mtu
<'VTSS_MAX_FRAME_LENGTH_STANDARD'-'V
TSS_MAX_FRAME_LENGTH_MAX'>
Use mtu to specify maximum frame size
(1518-9600 bytes).
15 INTERFACE_PORT_LIST
no mtu Use no mtu to set maximum frame size
to default.
15 INTERFACE_PORT_LIST
shutdown Use shutdown to shutdown the
interface.
15 INTERFACE_PORT_LIST
speed {2500 | 1000 | 100 | 10 | auto {[10] [100]
[1000]} }
Configures interface speed. If you use
10, 100, or 1000 keywords with the auto
keyword the port will only advertise the
specified speeds.
15 INTERFACE_PORT_LIST
no speed Use "no speed" to configure interface to
default speed.
15 INTERFACE_PORT_LIST
duplex { half | full | auto [ half | full ] } Use duplex to configure interface duplex
mode.
15 INTERFACE_PORT_LIST
no duplex Use "no duplex" to set duplex to default. 15 INTERFACE_PORT_LIST
media-type { rj45 | sfp | dual } Use media-type to configure the
interface media type.
15 INTERFACE_PORT_LIST
no media-type Use to configure the interface
media-type type to default.
15 INTERFACE_PORT_LIST
flowcontrol { on | off } Use flowcontrol to configure flow control
for the interface.
15 INTERFACE_PORT_LIST
no flowcontrol Use no flowcontrol to set flow control to
default.
15 INTERFACE_PORT_LIST
excessive-restart Use excessive-restart to configure
backoff algorithm in half duplex mode.
15 INTERFACE_PORT_LIST
show web privilege group [
web privilege group
[ crw <0-15> ] [ sro <0-15> ] [ srw <0-15> ] }*1
15 GLOBAL_CONFIG
no web privilege group [
show port-security port [ interface
Show MAC Addresses learned by Port
Security
0 EXEC
show port-security switch [ interface
Show Port Security status. 0 EXEC
no port-security shutdown [ interface
Reopen one or more ports whose limit is
exceeded and shut down.
15 EXEC
port-security Enable/disable port security globally. 15 GLOBAL_CONFIG
port-security aging Enable/disable port security aging. 15 GLOBAL_CONFIG
port-security aging time <10-10000000> Time in seconds between check for
activity on learned MAC addresses.
15 GLOBAL_CONFIG
no port-security aging time 15 GLOBAL_CONFIG
port-security Enable/disable port security per
interface.
15 INTERFACE_PORT_LIST
port-security maximum [<1-1024>] Maximum number of MAC addresses
that can be learned on this set of
interfaces.
15 INTERFACE_PORT_LIST
no port-security maximum 15 INTERFACE_PORT_LIST
port-security violation { protect | trap |
trap-shutdown | shutdown }
The action involved with exceeding the
limit.
15 INTERFACE_PORT_LIST
no port-security violation The action involved with exceeding the
limit.
15 INTERFACE_PORT_LIST
pvlan
to add or remove a port from a PVLAN.
13 INTERFACE_PORT_LIST
pvlan isolation Use the pvlan isolation command to add
the port into an isolation group.
13 INTERFACE_PORT_LIST
show pvlan [
the PVLAN configuration.
13 EXEC
show pvlan isolation [ interface
to view the PVLAN isolation
configuration.
13 EXEC
show qos [ { interface [
{ maps [ dscp-cos ] [ dscp-ingress-translation ]
[ dscp-classify ] [ cos-dscp ]
[ dscp-egress-translation ] } | storm | { qce
[ <1-256> ] } ]
15 EXEC
qos map dscp-cos { <0~63> |
dpl
15 GLOBAL_CONFIG
no qos map dscp-cos { <0~63> |
qos map dscp-ingress-translation { <0~63> |
15 GLOBAL_CONFIG
no qos map dscp-ingress-translation { <0~63> |
15 GLOBAL_CONFIG
qos map dscp-classify { <0~63> |
qos map cos-dscp <0~7> dpl <0~1> dscp { <0-63>
|
15 GLOBAL_CONFIG
no qos map cos-dscp <0~7> dpl <0~1> 15 GLOBAL_CONFIG
qos map dscp-egress-translation { <0~63> |
15 GLOBAL_CONFIG
no qos map dscp-egress-translation { <0~63> |
15 GLOBAL_CONFIG
qos wred queue <0~5> min-th <0-100> mdp-1
<0-100> mdp-2 <0-100> mdp-3 <0-100>
15 GLOBAL_CONFIG
qos wred queue <0~5> min-fl <0-100> max
<1-100> [ fill-level ]
15 GLOBAL_CONFIG
no qos wred queue <0~5> 15 GLOBAL_CONFIG
qos storm { unicast | multicast | broadcast }
{ { <1,2,4,8,16,32,64,128,256,512> [ kfps ] } |
{ 1024 kfps } }
15 GLOBAL_CONFIG
no qos storm { unicast | multicast | broadcast } 15 GLOBAL_CONFIG
qos qce { [ update ] }
[ interface
|
multicast | broadcast | any } ] [ tag { [ type
{ untagged | tagged | c-tagged | s-tagged | any } ]
[ vid {
[ dei { <0-1> | any } ] }*1 ] [ inner-tag { [ type
{ untagged | tagged | c-tagged | s-tagged | any } ]
[ vid {
[ dei { <0-1> | any } ] }*1 ] [ frame-type { any |
{ etype
[ { <0x600-0x7ff,0x801-0x86dc,0x86de-0xffff> |
any } ] } | { llc [ dsap { <0-0xff> | any } ] [ ssap
{ <0-0xff> | any } ] [ control { <0-0xff> | any } ] } |
{ snap [ { <0-0xffff> | any } ] } | { ipv4 [ proto
{ <0-255> | tcp | udp | any } ] [ sip {
any } ] [ dip {
{
any } ] [ sport {
{
| udp | any } ] [ sip {
{
{
15 GLOBAL_CONFIG
default } ] [ dpl { <0-1> | default } ] [ pcp-dei { <0-7>
<0-1> | default } ] [ dscp { <0-63> |
default } ] [ policy {
no qos qce <'QCE_ID_START'~'QCE_ID_END'> 15 GLOBAL_CONFIG
qos qce refresh 15 GLOBAL_CONFIG
qos cos <0-7> 15 GLOBAL_CONFIG
no qos cos 15 INTERFACE_PORT_LIST
qos dpl
no qos dpl 15 INTERFACE_PORT_LIST
qos pcp <0-7> 15 INTERFACE_PORT_LIST
no qos pcp 15 INTERFACE_PORT_LIST
qos dei <0-1> 15 INTERFACE_PORT_LIST
no qos dei 15 INTERFACE_PORT_LIST
qos trust tag 15 INTERFACE_PORT_LIST
qos trust dscp 15 INTERFACE_PORT_LIST
qos map tag-cos pcp <0~7> dei <0~1> cos <0-7>
dpl
15 INTERFACE_PORT_LIST
no qos map tag-cos pcp <0~7> dei <0~1> 15 INTERFACE_PORT_LIST
qos policer
no qos policer 15 INTERFACE_PORT_LIST
qos queue-policer queue <0~7>
qos queue-policer queue <0~7>
no qos queue-policer queue <0~7> 15 INTERFACE_PORT_LIST
qos wrr <1-100> <1-100> <1-100> <1-100>
<1-100> <1-100>
15 INTERFACE_PORT_LIST
no qos wrr 15 INTERFACE_PORT_LIST
qos shaper
no qos shaper 15 INTERFACE_PORT_LIST
qos queue-shaper queue <0~7>
no qos queue-shaper queue <0~7> 15 INTERFACE_PORT_LIST
qos tag-remark { pcp <0-7> dei <0-1> | mapped } 15 INTERFACE_PORT_LIST
no qos tag-remark 15 INTERFACE_PORT_LIST
qos map cos-tag cos <0~7> dpl <0~1> pcp <0-7>
dei <0-1>
15 INTERFACE_PORT_LIST
no qos map cos-tag cos <0~7> dpl <0~1> 15 INTERFACE_PORT_LIST
qos dscp-translate 15 INTERFACE_PORT_LIST
qos dscp-classify { zero | selected | any } 15 INTERFACE_PORT_LIST
no qos dscp-classify 15 INTERFACE_PORT_LIST
qos dscp-remark { rewrite | remap | remap-dp } 15 INTERFACE_PORT_LIST
no qos dscp-remark 15 INTERFACE_PORT_LIST
qos storm { unicast | broadcast | unknown }
<100-13200000> [ fps ]
15 INTERFACE_PORT_LIST
no qos storm { unicast | broadcast | unknown } 15 INTERFACE_PORT_LIST
qos qce { [ addr { source | destination } ] [ key
{ double-tag | normal | ip-addr | mac-ip-addr } ] }*1
15 INTERFACE_PORT_LIST
no qos qce { [ addr ] [ key ] }*1 15 INTERFACE_PORT_LIST
debug qos shaper cir { <100-3300000> [ cbs
<4096-258048> ] } { [ eir <100-3300000> [ ebs
<4096-258048> ] ] }
debug INTERFACE_PORT_LIST
no debug qos shaper debug INTERFACE_PORT_LIST
debug qos queue-shaper queue <0~7> { cir
<100-3300000> [ cbs <4096-258048> ] } { [ eir
<100-3300000> [ ebs <4096-258048> ] ] }
[ excess ]
debug INTERFACE_PORT_LIST
no debug qos queue-shaper queue <0~7> debug INTERFACE_PORT_LIST
debug show qos shapers debug EXEC
debug qos cmef [ { enable | disable } ] debug EXEC
show rmon statistics [<1~65535>] 15 EXEC
show rmon history [<1~65535>] 15 EXEC
show rmon alarm [<1~65535>] 15 EXEC
show rmon event [<1~65535>] 15 EXEC
rmon alarm <1-65535>
<1-2147483647> {absolute | delta}
rising-threshold <-2147483648-2147483647>
[<0-65535>] falling-threshold
<-2147483648-2147483647> [<0-65535>] {[rising
| falling | both]}
15 GLOBAL_CONFIG
no rmon alarm <1-65535> 15 GLOBAL_CONFIG
rmon event <1-65535> [log] [trap
{[description
15 GLOBAL_CONFIG
no rmon event <1-65535> 15 GLOBAL_CONFIG
rmon collection stats <1-65535> 15 INTERFACE_PORT_LIST
no rmon collection stats <1-65535> 15 INTERFACE_PORT_LIST
rmon collection history <1-65535> [buckets
<1-65535>] [interval <1-3600>]
15 INTERFACE_PORT_LIST
no rmon collection history <1-65535> 15 INTERFACE_PORT_LIST
show sflow statistics { receiver [
samplers [interface [
Use sflow statistics to show statistics for
either receiver or sample interface.
0 EXEC
show sflow Use show sflow to display the current
sFlow configuration.
0 EXEC
clear sflow statistics { receiver [
samplers [interface [
Clearing statistics. 15 EXEC
sflow agent-ip {ipv4
The agent IP address used as
agent-address in UDP datagrams.
Defaults to IPv4 loopback address.
15 GLOBAL_CONFIG
no sflow agent-ip Sets the agent IP address used as
agent-address in UDP datagrams to
127.0.0.1.
15 GLOBAL_CONFIG
sflow timeout [receiver
<0-2147483647>
Receiver timeout measured in seconds.
The switch decrements the timeout once
per second, and as long as it is
non-zero, the receiver receives
samples. Once the timeout reaches 0,
the receiver and all its configuration is
reset to defaults.
15 GLOBAL_CONFIG
no sflow timeout [receiver
The switch decrements the timeout once
per second, and as long as it is
non-zero, the receiver receives
samples. Once the timeout reaches 0,
the receiver and all its configuration is
reset to defaults.
15 GLOBAL_CONFIG
sflow collector-address [receiver
[
Collector address 15 GLOBAL_CONFIG
no sflow collector-address [receiver
sflow collector-port [receiver
<1-65535>
Collector UDP port. Valid range is
0-65536.
15 GLOBAL_CONFIG
no sflow collector-port [receiver
0-65536.
15 GLOBAL_CONFIG
sflow max-datagram-size [receiver
<200-1468>
Maximum datagram size. 15 GLOBAL_CONFIG
no sflow max-datagram-size [receiver
Maximum datagram size. 15 GLOBAL_CONFIG
sflow sampling-rate [sampler
[<1-4294967295>]
Specifies the statistical sampling rate.
The sample rate is specified as N to
sample 1/Nth of the packets n the
monitored flows. There are no
restrictions on the value, but the switch
will adjust it to the closest possible
sampling rate.
15 INTERFACE_PORT_LIST
sflow max-sampling-size [sampler
[<14-200>]
Specifies the maximum number of bytes
to transmit per flow sample.
15 INTERFACE_PORT_LIST
no sflow max-sampling-size [sampler
Specifies the maximum number of bytes
to transmit per flow sample.
15 INTERFACE_PORT_LIST
sflow counter-poll-interval [sampler
[<1-3600>]
The interval - in seconds - between
counter poller samples.
15 INTERFACE_PORT_LIST
no sflow counter-poll-interval [
counter poller samples.
15 INTERFACE_PORT_LIST
sflow [
port.
15 INTERFACE_PORT_LIST
show smtp Email information 0 EXEC
smtp delete { server | username | sender |
returnpath | mailaddress <1-6> }
Delete email server 15 GLOBAL_CONFIG
smtp mailaddress <1-6>
smtp returnpath
smtp returnpath
smtp sender
smtp username
smtp server
smtp level <0-7> 15 GLOBAL_CONFIG
show snmp 15 EXEC
show snmp community v3 [
show snmp user [
show snmp security-to-group [ { v1 | v2c | v3 }
show snmp access [
any } { auth | noauth | priv } ]
show snmp view [
snmp-server Enable SNMP server. 13 GLOBAL_CONFIG
snmp-server engine-id local
no snmp-server engined-id local To set SNMP server's engine ID to
default value.
15 GLOBAL_CONFIG
snmp-server version { v1 | v2c | v3 } Set the SNMP server version to
SNMPv1, SNMPv2c or SNMPv3.
15 GLOBAL_CONFIG
no snmp-server version Set SNMP server's version to default
setting.
15 GLOBAL_CONFIG
snmp-server community v2c
snmp-server community v3
[
15 GLOBAL_CONFIG
no snmp-server community v2c 15 GLOBAL_CONFIG
no snmp-server community v3
snmp-server user
15 GLOBAL_CONFIG
no snmp-server user
15 GLOBAL_CONFIG
snmp-server security-to-group model { v1 | v2c |
v3 } name
15 GLOBAL_CONFIG
no snmp-server security-to-group model { v1 | v2c
| v3 } name
15 GLOBAL_CONFIG
snmp-server access
v3 | any } level { auth | noauth | priv } [ read
15 GLOBAL_CONFIG
no snmp-server access
| v3 | any } level { auth | noauth | priv }
15 GLOBAL_CONFIG
snmp-server view
exclude }
15 GLOBAL_CONFIG
no snmp-server view
snmp-server contact
no snmp-server contact To clear the system contact string. 15 GLOBAL_CONFIG
snmp-server location
no snmp-server location To specify the system location string. 15 GLOBAL_CONFIG
show snmp mib context Use the show snmp mib context user
EXEC command to display \
the supported MIBs
in the switch.
15 EXEC
show snmp mib ifmib ifIndex Use the show snmp mib ifmib ifIndex 15 EXEC
user EXEC command to \
display the SNMP
ifIndex(defined in IF-MIB) mapping \
information in the
switch.
show snmp mib redefine Use the show snmp mib redefine user
EXEC command to display \
the redefined MIBs
in the switch, that are different \
definitions from the
standard MIBs.
15 EXEC
snmp-server trap 15 GLOBAL_CONFIG
no snmp-server host
shutdown 15 SNMPS_HOST
host {
[ traps | informs ]
15 SNMPS_HOST
host
no host 15 SNMPS_HOST
version { v1 [
[ probe | engineID
15 SNMPS_HOST
no version 15 SNMPS_HOST
informs retries <0-255> timeout <0-2147> 15 SNMPS_HOST
no informs 15 SNMPS_HOST
traps [ aaa authentication ] [ system [ coldstart ]
[ warmstart ] ] [ switch [ stp ] [ rmon ] ]
15 SNMPS_HOST
no traps 15 SNMPS_HOST
snmp-server host
[ linkdown ] [ lldp ]
15 INTERFACE_PORT_LIST
no snmp-server host
show snmp host [
[ interface ] [ aaa ]
15 EXEC
show ip ssh Use the show ip ssh privileged EXEC \
command to
display the SSH status.
15 EXEC
ip ssh Use the ip ssh global configuration
command to \
enable the SSH.
Use the no form of this \
15 GLOBAL_CONFIG
command to
disable the SSH.
show network-clock Show selector state. 0 EXEC
clear network-clock clk-source
network-clock clk-source
{ clk-in | {interface
Nominate a clk input to become a
selectable clock source.
15 GLOBAL_CONFIG
no network-clock clk-source
nominate
15 GLOBAL_CONFIG
network-clock input-source { 1544khz | 2048khz |
10mhz }
Sets the station clock input frequency 15 GLOBAL_CONFIG
no network-clock input-source 15 GLOBAL_CONFIG
network-clock output-source { 1544khz | 2048khz |
10mhz }
Sets the station clock output frequency 15 GLOBAL_CONFIG
no network-clock output-source 15 GLOBAL_CONFIG
network-clock clk-source
{ master | slave | forced}
Sets the preferred negotiation. 15 GLOBAL_CONFIG
no network-clock clk-source
aneg-mode
15 GLOBAL_CONFIG
network-clock clk-source
hold-timeout <3-18>
The hold off timer value in 100 ms.Valid
values are range 3-18.
15 GLOBAL_CONFIG
no network-clock clk-source
hold-timeout
15 GLOBAL_CONFIG
network-clock selector { { manual clk-source
holdover | freerun }
Selection mode of nominated clock
sources
15 GLOBAL_CONFIG
no network-clock selector 15 GLOBAL_CONFIG
network-clock clk-source
<0-1>
Priority of nominated clock sources. 15 GLOBAL_CONFIG
no network-clock clk-source
network-clock wait-to-restore <0-12> WTR time (0-12 min) '0' is disable 15 GLOBAL_CONFIG
no network-clock wait-to-restore 15 GLOBAL_CONFIG
network-clock ssm-holdover { prc | ssua | ssub |
eec2 | eec1 | dnu | inv }
Hold Over SSM overwrite 15 GLOBAL_CONFIG
no network-clock ssm-holdover 15 GLOBAL_CONFIG
network-clock ssm-freerun { prc | ssua | ssub |
eec2 | eec1 | dnu | inv }
Free Running SSM overwrite 15 GLOBAL_CONFIG
no network-clock ssm-freerun 15 GLOBAL_CONFIG
network-clock clk-source
ssm-overwrite { prc | ssua | ssub | eec2 | eec1 |
dnu }
no network-clock clk-source
ssm-overwrite
15 GLOBAL_CONFIG
network-clock option { eec1 | eec2 } EEC options 15 GLOBAL_CONFIG
no network-clock option 15 GLOBAL_CONFIG
network-clock synchronization ssm SSM enable/disable. 15 INTERFACE_PORT_LIST
show logging [ info ] [ warning ] [ error ] [ switch
Use the show logging privileged EXEC
command without keywords to display
the logging configuration, or particularly
the logging message summary for the
logging level.
15 EXEC
show logging <1-4294967295> [ switch
Use the show logging privileged EXEC
command with logging ID to display the
detail logging message.
OC_CMD_DEFAULT =
15 EXEC
clear logging [ info ] [ warning ] [ error ] [ switch
Use the clear logging privileged EXEC
command to clear the logging message.
15 EXEC
logging on Use the logging on global configuration
command to enable the logging server.
Use the no form of this command to
disable the logging server.
15 GLOBAL_CONFIG
logging host {
configuration command to configure the
host address of logging server.
15 GLOBAL_CONFIG
no logging host Use the no logging host global
configuration command to clear the host
address of logging server.
15 GLOBAL_CONFIG
logging level { info | warning | error } Use the logging level global
configuration command to configure
what level of message will send to
logging server.
15 GLOBAL_CONFIG
show clock Show running system information 0 EXEC
show version System hardware and software status 0 EXEC
password unencrypted
command to configure administrator
password with unencrypted password
15 GLOBAL_CONFIG
for the local switch access.
password encrypted
command to configure administrator
password with encrypted password for
the local switch access.
15 GLOBAL_CONFIG
password none Use the password none global
configuration command to remove the
administrator password.
15 GLOBAL_CONFIG
show system Show system information 0 EXEC
system contact
no system contact To clear the system contact string. 15 GLOBAL_CONFIG
system location
no system location To specify the system location string. 15 GLOBAL_CONFIG
system name
string.
15 GLOBAL_CONFIG
no system name To specify the system model name
string.
15 GLOBAL_CONFIG
show thermal-protect [interface
temperature and port status).
15 EXEC
thermal-protect prio <0~3> temperature <0-255> Thermal protection configuirations. 15 GLOBAL_CONFIG
no thermal-protect prio <0~3> Sets temperature at which to turn ports
with the corresponding priority off.
15 GLOBAL_CONFIG
thermal-protect port-prio <0-3> Sets temperature at which to turn ports
with the corresponding priority off.
15 INTERFACE_PORT_LIST
no thermal-protect port-prio Sets temperature at which to turn ports
with the corresponding priority off.
15 INTERFACE_PORT_LIST
show upnp 15 EXEC
upnp 15 GLOBAL_CONFIG
upnp ttl <1-255> 15 GLOBAL_CONFIG
no upnp ttl 15 GLOBAL_CONFIG
upnp advertising-duration <100-86400> 15 GLOBAL_CONFIG
no upnp advertising-duration 15 GLOBAL_CONFIG
username
unencrypted
Use the username
privilege
command to add a user with
unencrypted password for the local
15 GLOBAL_CONFIG
switch access.
username
encrypted
Use the username
privilege
command to add a user with encrypted
password for the local switch access.
15 GLOBAL_CONFIG
username
none
Use the username
privilege
configuration command to remove the
password for specific username.
15 GLOBAL_CONFIG
no username
global configuration command to delete
a local user.
15 GLOBAL_CONFIG
vlan protocol {{eth2 {<0x600-0xffff>|arp|ip|ipx|at}} |
{snap {<0x0-0xffffff>|rfc-1042|snap-8021h}
<0x0-0xffff>} | {llc <0x0-0xff> <0x0-0xff>} } group
13 GLOBAL_CONFIG
switchport vlan mac
to associate a MAC address to VLAN
ID.
13 INTERFACE_PORT_LIST
switchport vlan protocol group
Use the no form of this command to
remove the group to vlan mapping.
13 INTERFACE_PORT_LIST
show vlan protocol [eth2
{<0x600-0xffff>|arp|ip|ipx|at}] [snap
{<0x0-0xffffff>|rfc-1042|snap-8021h} <0x0-0xffff>]
[llc <0x0-0xff> <0x0-0xff>]
Use the switchport vlan protocol group
command to add group to vlan mapping.
13 EXEC
show vlan mac [address
show vlan ip-subnet [id <1-128>] 13 EXEC
switchport vlan ip-subnet id <1-128>
13 INTERFACE_PORT_LIST
no switchport vlan ip-subnet id <1~128> 13 INTERFACE_PORT_LIST
debug vcl policy
no debug vcl policy debug GLOBAL_CONFIG
debug show vcl policy debug EXEC
switchport mode {access | trunk | hybrid} Use the switchport mode command to
define the type of the port.
13 INTERFACE_PORT_LIST
no switchport mode 13 INTERFACE_PORT_LIST
switchport access vlan
command to configure a port to a VLAN.
Valid VLAN IDs are 1 to 4095.
no switchport access vlan 13 INTERFACE_PORT_LIST
switchport trunk native vlan
to configure a port VLAN ID for a trunk
port.
13 INTERFACE_PORT_LIST
no switchport trunk native vlan Set trunk mode characteristics of the
interface
13 INTERFACE_PORT_LIST
switchport hybrid native vlan
to configure a port VLAN ID for a hybrid
port.
13 INTERFACE_PORT_LIST
no switchport hybrid native vlan Set hybrid mode characteristics of the
interface
13 INTERFACE_PORT_LIST
switchport hybrid port-type { unaware | c-port |
s-port | s-custom-port }
Set hybrid characteristics of the
interface
13 INTERFACE_PORT_LIST
no switchport hybrid port-type Set hybrid characteristics of the
interface
13 INTERFACE_PORT_LIST
switchport hybrid ingress-filtering Set hybrid characteristics of the
interface
13 INTERFACE_PORT_LIST
switchport hybrid acceptable-frame-type { all |
tagged | untagged }
Set hybrid characteristics of the
interface
13 INTERFACE_PORT_LIST
no switchport hybrid acceptable-frame-type Set hybrid characteristics of the
interface
13 INTERFACE_PORT_LIST
switchport hybrid egress-tag {none | all
[except-native]}
Set hybrid characteristics of the
interface
13 INTERFACE_PORT_LIST
no switchport hybrid egress-tag Set hybrid characteristics of the
interface
13 INTERFACE_PORT_LIST
switchport trunk vlan tag native Set trunk characteristics of the interface 13 INTERFACE_PORT_LIST
switchport trunk allowed vlan {all | none | [add |
remove | except]
Set trunk mode characteristics of the
interface
13 INTERFACE_PORT_LIST
no switchport trunk allowed vlan Set trunk characteristics of the interface, 13 INTERFACE_PORT_LIST
switchport hybrid allowed vlan {all | none | [add |
remove | except]
Set hybrid characteristics of the
interface
13 INTERFACE_PORT_LIST
no switchport hybrid allowed vlan Set hybrid characteristics of the
interface
13 INTERFACE_PORT_LIST
vlan ethertype s-custom-port <0x0600-0xffff> 13 GLOBAL_CONFIG
no vlan {{ethertype s-custom-port} |
show interface
| trunk | hybrid]
Use the how interfaces command to
display the administrative and
operational status of all interfaces or a
specified interface.
0 EXEC
show vlan [id
VLAN configuration.
13 EXEC
show vlan status [ interface
[combined|admin|nas|mvr|voice-vlan|mstp|erps|vcl
|evc|gvrp|all|conflicts]
Use the show VLAN status command to
view the VLANs configured for each
interface.
13 EXEC
name
configure VLAN name.
13 CONFIG_VLAN
no name The no form of this command will
restore the VLAN name to its default.
13 CONFIG_VLAN
switchport forbidden vlan {add|remove}
the current list of forbidden VLANs
15 INTERFACE_PORT_LIST
no switchport forbidden vlan Allows for adding VLANs to an interface 15 INTERFACE_PORT_LIST
show switchport forbidden [{vlan
{name
Lookup VLAN Forbidden port entry. 0 EXEC
voice vlan Use the voice vlan global configuration
command to enable voice vlan. Use the
no form of this command to globally
disable voice vlan.
15 GLOBAL_CONFIG
voice vlan vid
configuration command to configure
voice vlan vid.
15 GLOBAL_CONFIG
no voice vlan vid Use the no voice vlan vid global
configuration command to restore the
default voice vlan vid.
15 GLOBAL_CONFIG
voice vlan aging-time <10-10000000> Use the voice vlan aging-time global
configuration command to configure
default voice vlan aging-time.
15 GLOBAL_CONFIG
no voice vlan aging-time Use the no voice vlan aging-time global
configuration command to restore the
default voice vlan aging-time.
15 GLOBAL_CONFIG
voice vlan class { <0-7> | low | normal | medium |
high }
Use the voice vlan class global
configuration command to configure
voice vlan class.
15 GLOBAL_CONFIG
no voice vlan class Use the no voice vlan class global 15 GLOBAL_CONFIG
configuration command to restore the
default voice vlan class.
voice vlan oui
configuration command to set the oui
entry for voice vlan.
15 GLOBAL_CONFIG
no voice vlan oui
configuration command to delete the oui
entry.
15 GLOBAL_CONFIG
switchport voice vlan mode { auto | force | disable } Use the switchport voice vlan mode
interface configuration command to
configure to switchport voice vlan mode.
15 INTERFACE_PORT_LIST
no switchport voice vlan mode Use the no switchport voice vlan mode
interface configuration command to
restore the default switchport voice vlan
mode.
15 INTERFACE_PORT_LIST
switchport voice vlan security Use the switchport voice vlan security
interface configuration command to
configure switchport voice vlan security
mode. Use the no form of this command
to globally disable switchport voice vlan
security mode.
15 INTERFACE_PORT_LIST
switchport voice vlan discovery-protocol {oui | lldp |
both}
Use the switchport voice vlan
discovery-protocol interface
configuration command to configure to
switchport voice vlan discovery-protocol.
15 INTERFACE_PORT_LIST
no switchport voice vlan discovery-protocol Use the no switchport voice vlan
discovery-protocol interface
configuration command to restore the
default switchport voice vlan
discovery-protocol.
15 INTERFACE_PORT_LIST
show voice vlan [ oui
Use the show voice vlan privilege EXEC
command without keywords to display
the voice vlan configuration, or
particularly switchport configuration for
the interface, or use the oui keyword to
display oui table.
15 EXEC
debug gvrp protocol-state interface
debug EXEC
debug gvrp msti debug EXEC
debug gvrp statistic debug EXEC
gvrp 15 GLOBAL_CONFIG
gvrp time { [ join-time <1-20> ] [ leave-time
<60-300> ] [ leave-all-time <1000-5000> ] }*1
15 GLOBAL_CONFIG
gvrp max-vlans <1-4095> 15 GLOBAL_CONFIG
gvrp 15 INTERFACE_PORT_LIST
gvrp join-request vlan
gvrp leave-request vlan
25 VERIPHY of CLI
VeriPHY keyword
Syntax
veriphy
veriphy interface [ * | GigabitEthernet ]
Parameter
interface Interface keyword
* All switches or All ports
GigabitEthernet 1 Gigabit Ethernet Port
Port list for all port types
Port list in 1/1-12
EXAMPLE
AW-IHT-1271# veriphy interface GigabitEthernet 1/1
Starting VeriPHY - Please wait
Interface Pair A Length Pair B, Length Pair C Length Pair D
Length
---------------------- ------ ------ -------------- ------ ------
------ -------
GigabitEthernet 1/1 OK 0 OK 0 OK 0 OK 0
AW-IHT-1271#
AW-IHT-1271# veriphy
Starting VeriPHY - Please wait
Interface Pair A Length Pair B, Length Pair C Length Pair D
Length
---------------------- ------ ------ -------------- ------ ------
------ -------
GigabitEthernet 1/1 Open 0 Open 0 Open 0 OK 0
GigabitEthernet 1/2 Open 0 Open 0 Open 0 OK 0
GigabitEthernet 1/3 Open 0 Open 0 Open 0 OK 0
GigabitEthernet 1/4 Open 0 Open 0 Open 0 OK 0
GigabitEthernet 1/5 OK 0 OK 0 OK 0 OK 0
GigabitEthernet 1/6 OK 0 OK 0 Open 0 OK 0
Related manuals for Vivotek AW-IHT-1271 Switch CLI User Guide
Manualsnet FAQs
If you want to find out how the AW-IHT-1271 Vivotek works, you can view and download the Vivotek AW-IHT-1271 Switch CLI User Guide on the Manualsnet website.
Yes, we have the CLI User Guide for Vivotek AW-IHT-1271 as well as other Vivotek manuals. All you need to do is to use our search bar and find the user manual that you are looking for.
The CLI User Guide should include all the details that are needed to use a Vivotek AW-IHT-1271. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.
The best way to navigate the Vivotek AW-IHT-1271 Switch CLI User Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.
This Vivotek AW-IHT-1271 Switch CLI User Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.
You can download Vivotek AW-IHT-1271 Switch CLI User Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.
To be able to print Vivotek AW-IHT-1271 Switch CLI User Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Vivotek AW-IHT-1271 Switch CLI User Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.