Vivotek AE-239 Outdoor Enclosure Installation Guide PDF

1 of 26
1 of 26

Summary of Content for Vivotek AE-239 Outdoor Enclosure Installation Guide PDF

IP Surveillance

Installation Guide

AE Series

Rev. 1.3

Outdoor Housing

Ordering part no.: AE-238 900041102G AE-239 900041202G AE-243 900041902G AE-244 900042402G AE-23A 900042302G AE-23B 900042201G AE-23C 900041701G AE-23D 900041801G AE-23E-v2 900060000G AE-23F 900042100G

2

I

Model Number AE-238, AE-243 AE-23A, AE-23B, AE- 23C, AE-23D

AE-239, AE-244 AE-23E-v2, AE-23F

Power Input 24V AC/ DC 24V AC/ 28V DC PoE: 50~57V DC PoE 802.3 bt, (AE-23E-v2) PoE 50~57V DC, (AE-23F)

Max. Output power budget

30W 80W, 100W (-AIW) 30W 15.4-30W PoE 30-60W PoE 60W - 95W PoE

Power Consumption Window heater: 10W; Blower: 2W; Camera: 6 ~ 8W

Window heater: 10W; Blower: 2W; Camera: 6 ~ 8W; Cold start heater: 30W

Window heater: 5W; Blower: 2W; Camera: 6 ~ 8W; IR: 6W

Window heater: 10W; Blower: 2W; Camera: 6 ~ 8W; Wiper: 6W

Environmental Operation Temp.

-20C ~ +65C -20C ~ +65C -20C ~ +50C (w/ IR) -40C (Cold start)

-20C ~ +65C -20C ~ +50C (w/ IR)

-20C ~ +65C -20C ~ +50C (w/ IR)

Window heater ON/OFF 30C ON; 35C OFF 30C ON; 35C OFF 30C ON; 35C OFF 30C ON; 35C OFF

Blower Control 40C ON; 35C OFF 40C ON; 35C OFF 40C ON; 35C OFF 40C ON; 35C OFF

Protection Level IP67, IK10 IP67, IK10 (IP66 w/ wiper) IP67, IK10 IP67, IK10 (IP66 w/ wiper)

Construction Die-cast Aluminum Alloy Die-cast Aluminum Alloy Die-cast Aluminum Alloy Die-cast Aluminum Alloy

Coating White epoxy powder coating

White epoxy powder coating

White epoxy powder coating

White epoxy powder coating

Dimensions 415 (L) x 170 (W) x 125 (H) mm

502.8 (L) x 170 (W) x 135.5 (H) mm

415 (L) x 170 (W) x 125 (H) mm - IR not included

502.8 (L) x 170 (W) x 135.5 (H) mm - IR not included

Net Weight 2,2kg (4.84 lb) 2,7kg (5.95 lb), 2,8kg (6.18 lb - wiper model)

2,2kg (4.85 lb) 2,7kg (5.95 lb), 2,8kg (6.18 lb - wiper model)

UNPACKING: Unpack carefully. Electronic components can be damaged if improperly handled or dropped. If an item appears damaged in shipment, place it properly in its carton and notify the shipper.

IMPORTANT!: 1. Read and follow Instructions: All operating and user instructions should be read and

followed before the unit is to be operated.

connections.

If you plan to install this camera enclosure into a tropical, sea coastal, or an environment where salt water or corrosive industrial waste water/moist are present, please seal each

This will help prevent electrolysis to occur and extend the life span of the camera and housing.

3

Revision History: Rev. 1.0: Initial release. Rev. 1.1: Added the Accessory list and updated environmental parameters: Added the distribution board drawing for the AE-23E and -23F.

Package Contents: 1. T30 L wrench. 2. 2x M4x8 3. Truss head screw: 1x 1/4"-20X1/4" 4. Truss head screw: 1x 1/4"-20X3/8" 5. 1x Plastic buffer plate:

IMPORTANT: 1. Disconnect devices: A readily accessible disconnect device in the building installation wiring

should be incorporated. 2.

Rev. 1.3 revise specification and part number of AE-23E/23F

4

II

Swivel Positions and Directions

415 mm

12 5

m m

170 mm

400 mm

255 mm

USABLE AREA

105 mm

77 .4

m m

USABLE AREA

105 mm

502.8 mm

13 5.

5 m

m

15 8.

5 m

m

170 mm

400 mm

77 .4

m m

USABLE AREA

255 mm

USABLE AREA

AE-238, AE-239

AE-23A, 23B, 23C, 23D, 23E-v2, 23F

415 mm

20 6.

9 m

m

170 mm

400 mm

135 mm 88

.0 5

m m

87.01 mm

AE-243, AE-244

5

E ng

lis h

Component DescriptionIII

Camera Mounting Platform

M16 1/2" Waterproof cable glands

AC/DC or PoE Power distribution board

Ventilation fan Window frame heater coil

21 7.

4 m

m

502.8 mm

417 mm

135 mm

88 .0

5 m

m

87.01 mm 95 R9

6.5 95

95

R96.45

Dimensions with the IR unit and wiper

VAIR module

Ground M4 x5

6

InstallationV

Installation SuggestionsIV

1. Prepare power wires, a ground wire, and a CAT5e Ethernet cable. Pass them through the M16 waterproof connectors and its waterproof components.

When installing a housing that comes with an IR illuminator:

Please avoid eye exposure or apply appropriate protection, such as wearing a pair of Infrared protection glasses, when working with the product. Always use camera live view to oberve IR lighting effects.

WARNING:

Ethernet cable 4 ~ 6.5mm

Power wires & DI/DO wires, a combo cable from IR illuminator (if applied)

Note that some cables are connected when shipped. You do not need to connect heater, blower, and the front IR powere wires.

7

E ng

lis h

o O g B b G br BR

1 2 3 4 5 6 7 8

o: white/orange stripe O: orange solid g: white/green stripe B: blue solid b: white/blue stripe G: green solid br: white/brown stripe BR: brown solid

You may need to remove the RJ45 connector, and use a crimping tool to connect the Ethernet wires to an RJ45 connector inside the enclosure. Use an Ethernet cable of the width of 5 ~ 6.5mm.

2. When done, tighten up and install the waterproof connectors.

3. Assemble the camera components, e.g., the CS ring and lens module. Secure the mounting plate to the bottom of the camera (the label side) using the included screw.

8

Lens flush w/ edge of enclosure

4. Adjust the camera's position so that the lens module can flush align with the tempered glass. Secure the camera using the screws and washers to the bottom of the housing.

Intrusion Alarm - Available on AE-23A/B/C/D/E/F.

If preferred, install the intrusion alarm switch to the side of enclosure, and connect the detection wires to camera DI.

9

E ng

lis h

5. Connect 24V power source to the power input terminal. Connect power wires from the DC 12V output to the camera. You may also connect the 24V power to drive an external IRs.

Below is the distribution board drawing power from 24V AC/DC.

Heater

Blower

IR angle selector

I/O terminal block

Camera heater 24V AC/DC IN 12V DC OUT

24V AC/DC OUT

Connectors to the front IR

Power LED

AE-23A, AE-23B, AE-23C, AE-23D

AE-238, AE-243

DC 12V OUT - to camera

AC 24V OUT - to external IR

AC 24V IN

Ground

for IR LED

AC 24V OUT - to camera

AC 24V IN

AE-238 AE-243

10

Below is the distribution board (AE-239, -244) that draws power from a 30/60/95W PoE PSE. Note that the AE-239 and AE-244 provide 12V DC output.

Heater

Blower

IR angle selector

PoE power LED

12V DC OUT PoE IN

Connectors to the front IR

Wiper / Camera heater PoE OUT

I/O terminal block (No use)

Below is the distribution board (AE-23E-v2/23F) that draws power from a 30/60/95W PoE PSE.

Heater

Blower

IR angle selector

PoE power LED

24V DC OUT PoE IN

Connectors to the front IR

Wiper / Camera heater PoE OUT

I/O terminal block

AE-23E-v2, AE-23F

AE-239, AE-244

11

En gl

is h

Below is the pinouts for the DI/DO terminal block for 23A/23B/23C/23D/23E-v2/23F-v2

Facing the rear side of the housing, from left to right: DO2 Tank water pump control DI2 Wiper control, connects to IP camera's DO for manually triggering washer. RS485+ RS485+, RS485 can be used to control IR illuminator beam angles, etc. RS485- RS485- DO+ +5V VCC DI- GND DO1 IR LED status, connects to IP camera's DI for IR status DI1 IR control, synchronizes day/night mode switching for IP camera. It is related to IR

The AE-239/244 support DO signal from IR control board.

DO+ IR LED status, connects to IP camera's DI for IR status DO- GND

12

beam angle for different effective illumination range. VAIR 48W 24W 6W no. of LEDs

18P/Dual 18P/36mil Single 4P/ 42mil Single

Beam angle

10 20 25 30 10 20 25 30 10 20 30 40

Jumper LL LH HL HH LL LH HL HH LL LH HL HH Distance (meter)

350m 280m 210m 150m 200m 155m 115m 70m 100m 80m 60m 40m

The following enclosures comes with adjustable IR lights: AE-23A/23B/23C/23D/23E-v2/23F-v2

HH HL LH LL

13

E ng

lis h

6. Connection for IR control by IR light sensor, RS485 commands and camera digital output 1. IR control by IR light sensor The day/night mode DI connection enables the synchronization of IR light sensor and then automated day/night switching mechanism on the camera.

D O

+ D

O -

D I1+

D I2+

D I3+

D I-

R S485-

R S485+

A C

/D C

pw r

A C

/D C

pw r

AWG26

D O

2 D

I2

D I-

R S485-

R S485+

D O

1 D

I1

D O

+

Tank ctrl W

iper ctrl

G N

D IR

LED IR

ctrl

5V VC C

Camera Terminal Block

Enclosure Terminal Block

2. IR control by RS485 command Allow user to configure the RS485 command via camera web UI to cotrol IR on/off.

D O

+ D

O -

D I1+

D I2+

D I3+

D I-

R S485-

R S485+

A C

/D C

pw r

A C

/D C

pw r

AWG20

AWG26

AC24V

D O

2 D

I2

D I-

R S485-

R S485+

D O

1 D

I1

D O

+

DC12V

Tank ctrl W

iper ctrl

G N

D IR

LED IR

ctrl

5V VC C

Camera Terminal Block

Enclosure Terminal Block

Note the wire gauge requirements for making the power connections. (24VAC 24W load) Wire Gauge 22 20 18 16 14 12 Distance 55 90 150 230 270 600 feet

14

D O

+ D

O -

D I1+

D I2+

D I3+

D I-

R S485-

R S485+

A C

/D C

pw r

A C

/D C

pw r

AWG20

AWG26

AC24V

D O

2 D

I2

D I-

R S485-

R S485+

D O

1 D

I1

D O

+

DC12V

Tank ctrl W

iper ctrl

G N

D IR

LED IR

ctrl

5V VC C

Tank ctrl Tank low water

GND

Camera Terminal Block

Enclosure Terminal Block

Below is a diagram for water tank and wiper control. The wiper can be started by manually triggering the Digital Output from the camera user interface.

2. IR control by Camera DO Camera will automatically trigger IR light on/off via DO.

D O

+ D

O -

D I1+

D I2+

D I3+

D I-

R S485-

R S485+

A C

/D C

pw r

A C

/D C

pw r

AWG26

D O

2 D

I2

D I-

R S485-

R S485+

D O

1 D

I1

D O

+

Tank ctrl W

iper ctrl

G N

D IR

LED IR

ctrl

5V VC C

Camera Terminal Block

Enclosure Terminal Block

15

E ng

lis h

7. If using the AM-21E wall-mount bracket, secure the intersection bracket to the bottom of the housing by driving two screws.

AM-11FAM-811AM-21D

AM-21E

Below are the mounting hole dimensions for the mounting brackets. Chances are you may need to plan for the locations of the brackets.

16

If using other mount brackets, use the included M6 screws to secure the housing to the bracket. Use the mounting holes indicated below.

x2

thread

Safety tether wire

8. Install the housing to the wall-mount bracket by aiming and pressing the spring mortise, and hook the bracket onto the groove in the spring mortise.

Secure the T30 anti-tamper screws on the other side using the included L-wrench.

Connect the included safety wire between enclosure and bracket.

17

E ng

lis h

The AM-21D wall-mount, AM-11F, and AM-811 pendant brackets use the two mounting holes as indicated below.

AM-21D

AM-11F

AM-811

Another two mounting holes in the front can be used use an IR bracket, AM-219. The bracket can be used to install external IRs.

AM-219

18

9. Adjust zoom and focus and open a web console with the camera to tune for the best image. When zoom and focus is done, Close the top cover and fasten the top cover screws.

The housing can also be installed using the pole-mount or corner-mount options along with a power box (AA-351, AA-352), outdoor PoE switch, or junction box.

CaMate IR illuminators

If external IRs are installed, you can contact VIVOTEK for a different type of waterproof connectors for the 1/2" conduits. You can then route two of the conduits through the opening in the front of the bracket to the corresponding connectors on the IR illuminators. The 24V power wires to the IR illuminators are contained within.

19

E ng

lis h

Use the included M10 hex socket screws to secure the power box to a pole-mount or corner mount bracket.

M10

3/4 conduit

AM-314 AM-315 AM-414

AM-21D

AM-21E

Box: AA-351 AA-352 AM-718

Outdoor PoE switch: AW-GEU-083A-240 AW-GET-083A-120 AW-GET-123A-240 AW-GEU-086A-240 AW-GET-086A-120 AW-GET-126A-240

Speed Dome: SD9361/62/63/64/65/66 SD83xx AM-212/221/220/21C

The mounting hole definition is illustrated below. The same mounting hole pattern apply to all pole- mount and corner-mount brackets.

20

AM-21D

AM-21E

If a power box or outdoor PoE switch is applied, Use the following mounting positions for the camera housings (via AM-21D and AM-21E).

10. If an IR illuminator is preferred, remove the metal cover from underneath the housing. Install the IR unit (AI-106, -108, -109) by fastening 4 T30 anti-tamper screws. Note that the bubber gasket should be in place when you install the unit.

21

E ng

lis h

11. Firmware configurable options:

Open a web console with the camera.

Use the Media > Focus function to tune for a best image focus on your target area.

If preferred, e.g., shooting fast moving vehicles, select the 60fps frame rate.

22

In the night mode, check if the input signals are correctly detected. You may simulate the night mode by blocking the IR unit's light sensor. Change the triggering parameters when necessary.

Make sure that external IR is turned on in the night mode, and that the IR cut filter option is synchronized with the digital input you connected.

23

E ng

lis h

Appendix: RS485 CommandsVI

For housings that come with IR illuminators, wiper, and washer, commands can be delivered via the RS485 protocol. The RS485 connection uses the Pelco D protocol.

Configuration parameters: Baud rate 2400 Data bits 8 Parity None Stop bit 1

Command format: Byte1 Byte2 Byte3 Byte4 Byte5 Byte6 Byte7 Sync Addr CMND1 CMND2 DATA1 DATA2 CKSM

Addr range: 0x00 ~ 0xFE. CKSM: check sum is the last 8 bits of the sum of Byte2 through Byte6.

Command Group 1: Command Description Command (hexadecimal, "ox" is

ommited) Note

VaIR Lens Stop FF 01 00 00 00 00 01 Pelco D - Zoom Stop VAIR Lens Wide FF 01 00 40 00 00 41 Pelco D - Zoom Wide VaIR Lens Tele FF 01 00 20 00 00 21 Pelco D - Zoom Tele Wiper On FF 01 00 09 00 01 0B Pelco D Aux 1 On Wiper Off FF 01 00 0B 00 01 0D Pelco D Aux 1 Off Wiper and Washer On FF 01 00 09 00 02 0C Pelco D Aux 2 On Wiper and Washer Off FF 01 00 0B 00 02 0E Pelco D Aux 2 Off IR Led Force On FF 01 00 09 00 03 0D Pelco D Aux 3 On IR Led Force Off FF 01 00 0B 00 03 0F Pelco D Aux 3 Off

Command Group 2: Command Name Command (hexadecimal, ox

is ommited) Note

Addr configuration FF 01 00 18 01 dd CKSM dd: 0x00 ~ 0xFE; for example, when addr is 2, the command looks like FF 01 00 18 01 02 1C

IRMode FF 01 00 18 02 mm CKSM mm: IR mode mm=0x02: Light Sensor Auto (Default) mm=0x03: DI Trigger mm=0x04: via RS485 Command (When receiving IR Led Force On / IR Led Force Off command, will switch to using the IR Mode -RS485 Command)

24

For example, IRmode_Auto FF 01 00 18 02 02 1D IRmode_DI FF 01 00 18 02 03 1E IRmode_CMD FF 01 00 18 02 04 1F

LightSensorGate FF 01 00 18 03 LL CKSM When the IR Mode Light Sensor Auto, the Lux value to turn IR LED can be configured.

LL: Lux, changes is made by every10Lux

For example: LightSensorGate = 100 FF 01 00 18 03 0A 26 LightSensorGate = 200 FF 01 00 18 03 14 30

The parameters of IR illuminator can be controlled via the RS485 connection. You can enable the connection in Configuration > PTZ > Mechanical window. Select the defaults for the IR illuminator: Pelco D, baud rate - 2400, Data bits - 8, Stop bit - 1, Parity - none.

Defaults for IR:

Pelco D 2400 8 1 none

Customizable IR control

25

E ng

lis h

VaIR Lens Stop

VAIR Lens Wide

FF 01 00 00 00 00 01

FF 01 00 40 00 00 41

VaIR Lens Tele

Wiper On

Wiper Off

FF 01 00 20 00 00 21

FF 01 00 09 00 01 0B

FF 01 00 0B 00 01 0D

You can create custom command buttons by entering the Button name and the command itself:

VaIR: The VAIR control include those on the IR Led and VaIR Lens.

There are 3 IR mode commands IRMode = Light Sensor Auto (Default) sensor lux reading < LightSensorGate - LED On sensor lux reading >= (LightSensorGate + 10 Lux ) - LED Off IRMode = DI_1 Trigger (IR triggered on by DI DI _1 shorted DI (Low) - LED On DI_1 open (High) - LED Off IRMode = controlled by RS485 Command (Pelco D Aux 3 On/Off) IR Led Force On - LED On IR Led Force Off - LED Off DO_1 as IR Status Feedback LED On, DO_1 is grounded via MOSFET (DI- connected) LED Off, DO_1 no input

VaIR Lens Zoom control Dip Switch 4 configurations using the Dip Switch on the distribution board. When Lens stops, its last position will be memoried,and when powered on again, lens will move to the previous position. When powered on for the first time, Lens will follow the DIP switch configuration.

Wiper & Wahser control) DI_2 Trigger: When DI_2 connected to DI- (Low), wiper and washer operate for 3 times and then stop.

Using RS485 Command Wiper Only (Pelco D Aux 1 On/Off) Wiper On, wiper takes action Wiper Off, wiper starts one operation and then stops.

RS485 Command Wiper & Washer (Pelc

Manualsnet FAQs

If you want to find out how the AE-239 Vivotek works, you can view and download the Vivotek AE-239 Outdoor Enclosure Installation Guide on the Manualsnet website.

Yes, we have the Installation Guide for Vivotek AE-239 as well as other Vivotek manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Installation Guide should include all the details that are needed to use a Vivotek AE-239. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Vivotek AE-239 Outdoor Enclosure Installation Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Vivotek AE-239 Outdoor Enclosure Installation Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Vivotek AE-239 Outdoor Enclosure Installation Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Vivotek AE-239 Outdoor Enclosure Installation Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Vivotek AE-239 Outdoor Enclosure Installation Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.