Vivotek AP-GIC-015B-095 Injector Installation Guide PDF

1 of 8
1 of 8

Summary of Content for Vivotek AP-GIC-015B-095 Injector Installation Guide PDF

IP Sur vei l lance

Installation Guide

AP-GIC-015B-095 Surveillance PoE Junction Box

Rev.: 1.0

2

CAUTION: REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

UNPACKING: Unpack carefully. Electronic components can be damaged if improperly handled or dropped. If an item appears damaged in shipment, place it properly in its carton and notify the shipper.

1. The electrical connections and conduit installations shall be made by a certified electrician following local regulations.

2. Risks of electric shock exist. The mains supply shall be disconnected before installation. 3. Read and follow Instructions: All operating and user instructions should be read and followed before

the unit is to be operated. 4. This product relies on the building's installation for short-circuit (overcurrent) protection. Ensure that

the protective device is listed rated not greater than 20A. 5. Attach the ground wire (to external ground) to a suitable grounding point, e.g., an earth stake. 6. Observe national and local regulations for the installation. 7. To avoid additional accummulation of moisture, please avoid installing the components in cabinet

during a raining weather. 8. Only use applicable tools when installing this product; excessive force can damage the product. 9. Use only accessories compliant with the technical specifications of the product. 10. When the need arises for transportting this product, it is recommended to use the original shipping

package.

IMPORTANT!:

Revision History:

Rev. 1.0: Initial release.

Mechanical Dimensions:

3

En gl

is h

Applicable Mount & BracketsI

Item Models Applicable Cameras Junction box AP-GIC-015B-095 SD9365, SD9366, SD9363, SD9364

External housings

AE-239, AE-244, AE-23E, AE-23F Box cameras

100~240V Line IN

Ground Neutral

to camera from network

for power wires

for Ethernet cables

WiringII

Route your power wires through a 3/4" conduit into the power box. The wiring scheme is shown below. The power supply converts 100~240V power to the 95W PoE output to IP cameras.

4

Introduction

The power box can be mounted with the AM-314, AM315 pole-mount, AM-414 corner-mount bracket, or directly secured to a wall.

III

The power box can be mounted with the external housings, such as the AE-239, AE-244, AE-23E, and AE-23F.

5

En gl

is h

Use the included M10 hex socket screws to secure the power box to a pole-mount or corner mount bracket.

InstallationIV

M10

3/4 conduit

AM-314 AM-315 AM-414

For this PoE junction box

Pole-mount bracket

Pole-mount bracket Corner-mount bracket

The mounting hole definition is illustrated below. The same mounting hole pattern apply to all pole- mount and corner-mount brackets.

6

If the power box is directly mounted to wall, drill holes in a diameter of 9.5mm or 3/8", and 4cm deep.

AM-21D

AM-21E

M8

Use the following mounting positions for the camera housings (via AM-21D and AM-21E brackets).

7

En gl

is h

This page is intentionally left blank.

Manualsnet FAQs

If you want to find out how the AP-GIC-015B-095 Vivotek works, you can view and download the Vivotek AP-GIC-015B-095 Injector Installation Guide on the Manualsnet website.

Yes, we have the Installation Guide for Vivotek AP-GIC-015B-095 as well as other Vivotek manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Installation Guide should include all the details that are needed to use a Vivotek AP-GIC-015B-095. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Vivotek AP-GIC-015B-095 Injector Installation Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Vivotek AP-GIC-015B-095 Injector Installation Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Vivotek AP-GIC-015B-095 Injector Installation Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Vivotek AP-GIC-015B-095 Injector Installation Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Vivotek AP-GIC-015B-095 Injector Installation Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.