Vivotek AM-712 Conduit Box Installation Guide PDF

IP Sur vei l lance

Installation Guide

VIVOTEK Fixed Dome Series Extender Conduit Box

Using AM-712 conduit box, AP-FXC-0210 PoE Extender, and compatible accessories

Rev. 1.3

Corresponding part number: AM-712: 909004720G (v03) AM-221: 900014801G AM-118: 900014601G AM-522: 900020201G

2

B

B

NEW_VIEW_7

NEW_VIEW_7

C C

n 1 52. 4

n 9 D P1-3 X

44 ` 0. 1

1. 6

1. 7

21

n 3 .5

3

n 33 D P3

71.3

9

n 15 0.6

n 3 ` 0.1 L1.5-2X

n 6 L14-4 X

71.3

NP T 3/4 "-3 X

16 .5

n 4.5-3X

A

A

A

B

B

B

B

B C

C

M3X0.5 DP5-5X88.9

106

138

AM-712 Conduit Box Mechanical Drawings

Revision History: * Rev. 1.0: Initial Release * Rev. 1.1: Added FD8367-TV, FD8167-T, and FE8180 as the supported models. * Rev. 1.2: Added corresponding part numbers, and FD8169 as supported model. * Rev. 1.3: Updated the corresponding part numbers of accessories.

Package Contents

Item No. AM-712 conduit box

Conduit box 1

3

E ng

lis h

Physical Description - Use

100m 100m 100m

PoE switch

AP-FXC-0210 PoE Extender

1 2 3 4 1 2 3 4

LAN

PoE

UPLINK PoE

ON

OFF

4xFE PoE + 1xFE Switch UPLINK

POWER ON

* The NPT (National Pipe Taper) or PT pipes with male threads are user-supplied. ** The last conduit box does not need to contain a PoE extender.

Item No. Screw pack

M3x6 round head w/ washer (nickel and nylok) 7mm; (for securing dome cameras to the base plate)

5

#6-32 L6 truss head (nickel and nylok) 8mm (for direct installation to a junction box)

2

Anchors 3

Pan head M4x25, zinc-plated, self-tapping screws (for direct installation to ceiling)

3

M3x6 pan washer head 2

4

Alignment notch

For countersunk head screws

Physical Description - Bottom

Physical Description - Top

For attaching to juction box

For attaching to juction box

For 3/4 conduits

For NPT or PT pipe

5

E ng

lis h

InstallationII

Above are the locations of different groups of mounting holes for matching different cameras: Hole Type

Applicable Cameras Screw No. of screws

A FD8137HV/ FD8154V / FD8164V

M3x6 round head

3 B FD8137H / FD8154 / FD8164 / FD8169 3 C FD8131V / FD8133V/ FD8134V 3 D FD8131 / FD8133 / FD8134 2 E FD8151V / FD8152V 2 F FD8136 / FD8166 2

G FE8180 M3x6 pan washer head 2

H FD816BA-HF2, FD816BA-HT, FD8182-F2, FD8182-T, FD9171-HT, FD9181-HT M3x6 round head

3

I FD8367-V / FD8367-TV / FD8338-HV 3

Mounting Hole Definitions

Compatible VIVOTEK CamerasI

Fixed Dome series FD8152V, FD816BA-HF2, FD816BA-HT, FD8182-F2, FD8182-T, FD9171-HT, FD9181-HT, FE8180, FD8166A, FD8166A-N

You may also refer to VIVOTEK's website for the list of supported models. Support for other models can be available through time.

6

NOTE:

1. The AM-522 is necessary when installing the AM-712 mounting cap to VIVOTEK's standard mounting options such as AM-212 (wall mount bracket) and AM-221 (gooseneck).

The AM-522 features the mounting option for NPT pipes only. 2. Route cables before you secure the accessories to a wall. 3. For details on the cable connections with each camera, please refer to their Quick

Installation Guide.

For cabling and configuration details with each network camera, please refer to their documentation.

7

E ng

lis h

Configuration - Pendant Pipe

3/4 pendent pipe

AM-712

AM-522 adapter AM-118 pendant head

3/4 female adapter

Note: The 3/4" female adapter and pendant pipes are separately purchased.

Configuration - Gooseneck

AM-712

AM-522 adapter

AM-221 gooseneck

NOTE:

The following mount types do not apply to PT pipes.

8

NOTE:

When installing the mounting cap, take note that the orientation of the mounting cap can affect the camera's shooting direction. You may need to disconnect the conduit box from the NPT pipe, rotate, and re-install it for the best orientation.

Configuration - Wall Mount

AM-712

AM-522 adapter

AM-212 Wall-mount bracket

9

E ng

lis h

Refer to the matching table on page 4 for the mounting hole information for your camera. III-1. Installing Camera to Conduit Box

1. Remove the base plate from the bottom of the conduit box. 2. You can route cables through other accessories before you install cameras to the base

plate.

3. Orient and install the camera to the base plate (to the side with printed characters). 4. Connect cables to the camera. 5. Install the base plate to the conduit box. 6. Proceed with initial setup such as enabling network access, focus tuning, or zooming.

When done, secure the outer dome cover.

10

A

A

A

The A Screw Holes: FD8154V / FD8137HV / FD8164V

Some installation samples are shown below:

NOTE:

Orient the camera so that cables coming out from the camera can pass through the cabling hole on the base plate.

11

E ng

lis h

B holes

B

B

B

M4X12 Screws

C holes

C

C C

The B Screw Holes: FD8154 / FD8137H / FD8164 / FD8169

The C Screw Holes: FD8131V / FD8133V / FD8134V

12

The D Screw Holes: FD8131 / FD8133 / FD8134

D

D

13

E ng

lis h

The E Screw Holes: FD8151V / FD8152V

E holes

E

E

The F Screw Holes: FD8166A / FD8166A-N

F holes

14

M3X6 Screws G holes

The G Screw Holes: FE8180

M3X0.5 L6 Screws H holes

The H Screw Holes: FD816BA-HF2, FD816BA-HT, FD8182-F2, FD8182-T, FD9171-HT, FD9181-HT

15

E ng

lis h

M3X0.5 L6 Screws I holes

The I Screw Holes: FD8367 and 8338 Series

16

III-2. Installing the Pendant Head and Pipe

3/4pendent pipe

AM-522 adapter AM-118 pendant head

3/4 female adapter

Below are the sample procedures using a pendant head and pendant pipe: 1. Determine a hard surface ceiling location, and use the alignment sticker to mark the

positions where holes will be drilled to secure the pendant head. Hammer the anchors into the ceiling.

Note that mounting holes should be 10mm in diameter and 60mm deep. The included screws are M6.2 x75mm.

2. Install an NPT or PT male thread pipe (length determined by installers) by turning it clockwise to the pendant head, and secure the connection using an included 3mm hex wrench.

NOTE:

This mount type applies to NPT pipes only.

For NT pipes, fixture on the other end should be handled by users.

17

E ng

lis h

3. Route Ethernet cable and other wires through the pendant head. You may apply a 1 inch conduit.

Note that when routing Ethernet cables, please make sure you have tagged the cables as PoE input (coming from a PoE switch), or PoE output (one that transmit data and power to the next conduit box).

4. Secure the pendant head to ceiling by driving screws through its mounting holes. Depending on the length of your cables, you may need the help from your colleague for holding the components.

Pendant Head Cables

18

A

A

A

B

B B

B

B C

C

Connector side

1. Pull cables through the NPT pipes and then the conduit box. 2. Install the conduit box to the NPT pipe. 3. When done, install the PoE extender by driving 2 screws to the conduit box, its

connector side facing the inside of the box.

III-3. Installing the Conduit Box and PoE Extender

4. In a cascade topology, there should be 2 Ethernet cables in the pipe. One is used as PoE input, the other as the out port to the next conduit box.

PoE IN PoE OUT to another conduit box

PoE OUT to camera

You may use cable tags to identify PoE cables.

19

E ng

lis h

5. Pull the Ethernet cable (and/or I/O wires) through the cabling hole on the base plate. 6. Orient the align