Vivotek AM-221 Bracket Installation Guide PDF

1 of 24
1 of 24

Summary of Content for Vivotek AM-221 Bracket Installation Guide PDF

IP Survei l lance

Installation Guide

VIVOTEK SD83XXE Speed Dome

Mounting Accessories AM-116/117 Pendant Pipe AM-118 Pendant Head AM-221 Gooseneck AM-231 Parapet Mount AM-519 Pendant Adaptor

Rev. 1.1

Corresponding part numbers:

AM-116: 900014300G AM-117: 900014400G AM-118: 900014600G AM-221: 900014800G AM-231: 900015000G AM-519: 900014900G

2

Compatible VIVOTEK CamerasI

Speed Dome SD8364E, SD8363E, SD8333E, SD83x4E, SD83x6E, SD8362E

AM-118 Pendant Head

Revison History: Rev. 1.0: Initial release Rev. 1.1: Adding corresponding ordering part numbers and supported speed dome models.

A

90

20

26.2

R 1

26.2

77 .9 4

25 .9 8

28 .0 4

20

R5

8. 5

50

M6

R8 R5

60.3 R2 R5

20 32 .2

R2

10

4

52 .2

10

6

15

1-1/2" PS11

Mechanical DrawingsII

3

E ng

lis h

AM-116 20cm Pendant Pipe

n 50.8

17

22 8

1 1/2" PS11

AM-117 40cm Pendant Pipe

n 50.8

17

40 0

35

42 8

1 1/2" PS11

1 1/2" PS11

37,5

50,8 46

60,3

17 8

5, 38

5, 25

28

45

R0 ,5

3

43,6 1-1/2" PS11X17mm (L)

C4

AM-519 Pendant Adapter (comes with the network camera)

4

AM-221 Gooseneck

405.8

26 2. 19

140

350 107.8

16 5. 5

20 027 8

AM-231 Parapet Mount

11 93

1077.95

997

46 3

228.15

5

E ng

lis h

AM-231 Parapet Corner Mount

11 93

1077.95

997

202.95

46 3

6

AM-231 Parapet Mount - Alignment Sticker

178.15

10 0

18 0

18 0

n 1 0

228.15

49 5

parapet top

AM-231 Corner Mount - Alignment Sticker

10 0

18 0

18 0

143.5

287

n 10

49 5

Fold Line

PARAPET TOP

7

E ng

lis h

Preparation before InstallationIII

1

2

Connect Ethernet cable and IO wires (this may include the AC24V wires) to the interface section of the camera, and then combine the interface section with the dome cap. Note that you must route cables through the waterproof connector and the rubber seal plug, and install them to the dome cap. Please refer to the Quick Installation Guide for details.

Cabling should be done before mounting the camera.

The top section will look like this.

8

Mounting & CablingIV

446.2 mm

AM-118

AM-117

AM-519

321.4 mm

204.8 mm

Shown below are the dimensions of a pendant mount configuration using the 40cm pendant pipe.

IV-1. Pendant Pipe Mounting: AM-116/-117 & AM-118

9

E ng

lis h

AM-519

IV-1-1. Pendant Mount without Pendant Pipe: AM-118

Below are the sample procedures using a pendant head and pendant pipe: 1. Determine a hard surface ceiling location, and use the alignment sticker to mark the

positions where holes will be drilled to secure the pendant head. Hammer the anchors into the ceiling.

Note that mounting holes should be 10mm in diameter and 60mm deep. The included screws are M6.2 x75mm.

2. Install a pendant adapter (AM-519) by turning it clockwise to the pendant head, and secure the connection using an included 3mm hex wrench.

10

3. Route power lines and other wires through the pendant head. You may apply a 1 inch conduit.

4. Secure the pendant head to ceiling by driving screws through its mounting holes. Depending on the length of your cables, you may need the help from your colleague for holding the camera top section.

Pendant Head

Camera top section

Cables

11

E ng

lis h

5. Secure the camera's top section to the pendant head by fastening 3 M5x8 screws. When done, secure the connection using an included 3mm hex wrench.

6. Install the camera to the top section. See your Quick Installation Guide or page 15 for details.

12

IV-1-2. Pendant Mount with Pendant Pipe: AM-116/AM-117 & AM-118

Below are the sample procedures using a pendant head and pendant pipe: 1. Determine a hard surface ceiling location, and use the alignment sticker to mark the

positions where holes will be drilled to secure the pendant head. Hammer the anchors into the ceiling.

Note that mounting holes should be 10mm in diameter and 60mm deep. The included screws are M6.2 x75mm.

2. Install a 20cm or 40cm pendant pipe (AM- 116 or AM-117) by turning it clockwise to the pendant head, and secure the connection using an included 3mm hex wrench.

13

E ng

lis h

3. Route power lines and other wires through the pendant head. You may apply a 1 inch conduit.

4. Secure the pendant head to ceiling by driving screws through its mounting holes. Depending on the length of your cables, you may need the help from your colleague for holding the camera top section.

Pendant Head

Camera top section

Cables

14

5. Secure the camera's top section to the pendant head by fastening 3 M5x8 screws.

6. Install the camera to the top section. See your Quick Installation Guide or page 15 for details.

15

E ng

lis h

IV-2. Gooseneck Mounting: AM-221 Below is a sample procedure using a gooseneck bracket: 1. Determine a hard surface wall location. Use the alignment sticker to mark the positions

where holes will be drilled for the gooseneck bracket.

1

2 3

5

HD WDR Pro

4

2. Drill 4 pilot holes (10mm in diameter and 5.5cm deep) into the wall, and then hammer in threaded anchors. Note that you should hammer the anchors with hex nuts on them so that the threaded poles will not be deformed! If preferred, drill another hole for routing cables.

3. Secure the wall mount bracket to wall using 4 sets of lock washers and nuts.

4. Attach the top section (dome cap and interface section) of the camera to the gooseneck bracket

5. Align the camera body with the top section. Align the alignment mark on the camera with that on the interface section. Push the camera up to match the top section.

Install AM-519 adaptor to the gooseneck.

Alignment mark

16

6. Rotate the camera clockwise until its alignment mark is aligned with the "C" mark. 7. Use the included T25 stardriver to tighten the 3 anti-tamper screws from the top. Make

sure all parts have been securely tightened.

6

7

HD WDR Pro

HD WDR Pro

The dimensions of the gooseneck installation are shown below.

380.4

25 8

57 9

C mark

17

E ng

lis h

IV-3. Parapet Mounting: AM-231

The screws included in the parapet set are:

Sleeve anchors 5/16" x3" 6 Hex bolts M8x25 6 Hex bolts M8x70 3 Hex lock nuts M8 6 Washers M8 15 Lock washers M8 15

978.4

66 5

978.4

66 5

65

52 8

Parapet

Front view

Side view

Room for routing cables

The parapet bracket is designed for installation on the inside of a parapet. Note the following before you start to install: 1. There must be a clearance of 65mm between the upper edge of the parapet wall and

the metal bracket fixed to the wall. You can flush align the upper edge of the alignment sticker with the edge of a parapet wall.

2. At least two inches of space should be available below the parapet bracket for routing cables.

The space requirements for a parapet mount are shown below:

The parapet wall should have a concrete strength of 4000 PSI or higher. Each sleeve anchor can withstand an 800kgs pull-out force.

IMPORTANT:

18

Below is a sample procedure using the parapet mount bracket: 1. Determine a hard surface location. Use the alignment sticker to mark the positions

where holes will be drilled for the bracket. 2. Drill 6 pilot holes (10mm in diameter and 5.5cm deep) into the wall, and then hammer

in the sleeve anchors. Note that you should hammer the anchors with hex nuts and washers on them so that the threaded poles will not be deformed!

65

52 8

Parapet wall

3. Install the brackets to wall using the hex nuts and washers from the sleeve anchors.

19

E ng

lis h

If you install the corner parapet bracket, use the included alignment sticker, and mark the drill holes through the mounting slots on the brackets.

NOTE:

20

4. Use a crescent wrench to secure the outer brackets to the brackets on the wall using the M8x25 hex bolts and washers. Do not completely tighten the bolts yet! When the speed dome is installed to the mount pipe, it needs to be swiveled out to the desired position.

6. Feed cables through the pipe arm. The cable length for passing through the pipe arm is 250cm at least. You can pass a rigid copper wire through the pipe arm first, and use it to pull other wires through the pipe.

5. Install the AM-519 adapter to the parapet pipe.

21

E ng

lis h

7. Install the top section of the camera to the pipe arm by driving 3 M5 x8 screws.

8. Insert the pipe arm into the round openings on the brackets until it is rested on the bottom bracket.

22

9. Install the camera to the top section. For installation details, refer to the Quick Installation Guide or page 15 in this document.

10. Swivel the pipe arm outwards to the opposite position. Use the M8 x70 bolts to secure the pipe arm to the brackets. You also need to tighten the M8 x25 bolts between the inner and outer brackets.

IMPORTANT:

When inserting the M8 bolts, you may damage the cables inside. Try twist the bolts a bit to get around cables if you feel resistance when inserting through the pipe.

23

E ng

lis h

A corner parapet installation should look like this when its installa

Manualsnet FAQs

If you want to find out how the AM-221 Vivotek works, you can view and download the Vivotek AM-221 Bracket Installation Guide on the Manualsnet website.

Yes, we have the Installation Guide for Vivotek AM-221 as well as other Vivotek manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Installation Guide should include all the details that are needed to use a Vivotek AM-221. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Vivotek AM-221 Bracket Installation Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Vivotek AM-221 Bracket Installation Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Vivotek AM-221 Bracket Installation Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Vivotek AM-221 Bracket Installation Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Vivotek AM-221 Bracket Installation Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.