Compatible VIVOTEK CamerasI
Compatible brackets Supported Cameras AM-714 IB836BA-EHF3/EHT/HF3/HT, IB8382-EF3/ET/F3/T, IB9371-EHT/HT, IB9381-EHT/HT AM-719 IB836BA-EHF3/EHT/HF3/HT, IB8382-EF3/ET/F3/T, IB9371-EHT/HT, IB9381-EHT/HT,
IB9365-EHT/HT, IB9367-EHT/HT/H, IB8377-EHT/HT
AM-218 (via AM-714/ AM-719)
Please refer to AM-218, AM-520, and AM-525 documents.
Directly attached Supported Cameras * IB836BA-EHF3/EHT/HF3/HT, IB8382-EF3/ET/F3/T, IB9371-EHT/HT, IB9381-EHT/HT,
IB9365-EHT/HT, IB9367-EHT/HT/H, IB8377-EHT/HT, IB8367A, IB8369A, IB8377-H, IB8379-H, MS8391-EV, MS9390-HV, IB9367-EHT-v2
* The directly-attached configuration is less recommended for the lack of waterproof and cabling protection. If directly attached, you should properly wrap the rear-end cables and connectors with waterproof protection such as putties.
Revision History: Rev. 1.0: Initial release; Rev. 1.1: Added mounting holes for IB8367A, IB8369A, IB8377, and IB8379. Rev. 1.2: Added MS9390-HV as the supported model. Rev. 1.3: Added IB9367-EHT-v2 as the supported model.
Corresponding ordering part numbers: AM-312: 900034801G, AM-714: 100134800G AM-218: 100146100G AM-719: 100184500G
VIVOTEK Mounting Accessories AM-312 Pole mount
Installation Guide
https://www.dropbox.com/sh/eo7e72dc1vh6vtc/AADVuNErcli6woSgWBA1RyDta?dl=0
Package Contents Items 1. Pole mount bracket, 2. Stainless strap x2, 3. M6X20mm screws x4. 4. M5X20mm
screws x4, 5. Hex L wrench 5mm x1, 6. Hex L wrench 4mm x1, 7. M4x15 screws x4.
AM-312 Pole mount bracket
Mechanical DrawingsII
173,79
17 045
4- 6
10 2
2
5555
70 ,0
5
86
4- 7
84,9
86
99
56,29
48 ,7
5
3- 4,5
68 ,7
5
4-OB 25.5X5.5mm
M6X20 X4
5mm X1
M5X20 X4
4mm X1
Stainless steeel strap X2
M4X15 X4
AM-312 Applications
Bullet camera
AM-312
AM-218 AM-714 / AM-719
Dome camera
AM-520 / AM-525, etc.
AM-312
AM-714 / AM-719
InstallationIII
Below is a general, sample procedure using a Pole mount bracket: 1. Pass the stainless steel straps through the bracket and around the pole. 2. Tighten the straps using a pincer plier and a flat blade screwdriver.
3. The 4 screw holes in the center are used for directly mounting the IB series bullet cameras.
The 4 screw holes at the edges are used for mounting the AM-714 conduit box.
For M6 socket screws - for IB series bullet cameras directly attached
Also applies to MS9390 using the M4 screws
The pole mount bracket is designed to accommodate a pole in a diameter ranging from 90 ~ 152mm (3.5 ~ 6 inches)
Make sure you have purchased the adequate accessories to be combined for your installation. Please do not install an indoor camera in an outdoor environment! Doing so will void our
warranty. This is determined by whether the camera housing is weather-proof. Direct sunlight can tremendously increase the temperature within the device.
Installation Torque: 35 lb-in(40kg-cm)
For M5 socket screws - for AM-714/AM-719 conduit box
4. Secure the AM-714 / AM-719 conduit box to bracket using the M5 screws, washers, and hex heads. A hex crescent wrench is required.
M5
If you are installing a bullet camera directly to the bracket, use the M6 screws in the center. A hex crescent wrench is required.
M5
5. For the rest of the installation procedure, refer to the documentation that came with the AM-714, AM-719, AM- 218, and the other accessories.
The 3/4" cable glands and conduts for protecting cables are user-supplied.
Rev. 1.3
The 3 screw holes in the center are used for mounting the IB8367A, IB8369A, IB8377-H, IB8379-H bullet cameras.
For M4 screws - for IB8367A, IB8369A IB8377-H, IB8379-H
The installation of IB8367A, IB8369A, IB8377, and IB8379 is similar to the above, except using different mounting holes and screws.