Viking DDSB542 Refrigerator Side Panel Kit Instructions PDF

1 of 2
1 of 2

Summary of Content for Viking DDSB542 Refrigerator Side Panel Kit Instructions PDF

INSTALLATION INSTRUCTIONS dSSPL/dSSPR designer SERIES SIDE PANEL KIT

VIKING 111 Front Street

Greenwood, Mississippi 38930 USA (662)455-1200

For Use with Built-In Refrigerator/Freezers and Full Height Wine Cellars

IMPORTANT - PLEASE READ AND FOLLOW Before beginning, please read these instructions completely and carefully. Do not remove permanently affixed labels, warnings or plates from the product. This may void the warranty. Please refer to the installation instructions included with the product for site preparations and considerations. The installer should leave instructions with the consumer who should retain for local inspector's use and for future reference.

CAUTION: Always wear gloves when handling the side panels. Some edges may be sharp enough to cause injury during handling.

WARNING! The unit must be fastened to a wall located at the rear of the product. Failure to properly fasten the product to the wall can result in death or serious injury. See installation instructions included with the product for proper securing methods.

Parts Included: Required Tools: (1) Stainless steel side panel Electric drill (5) Black #8 sheet metal screws (Part number - M0210443) 9/64" (.36 cm) diameter drill bit

NOTE: For DSSPL3, there will be (12) black #8 sheet metal screws (3) Foam strips - attached to the panel (Part number - PM910067)

To install: 1. If a top panel kit was purchased in addition to the side panel kit, refer to installation instructions included with the

top panel kit. 2. Locate the unit in front of the area in which it is to be installed (approximately two feet directly in front of the final

position). 3. If a DSSPL3 was purchased, refer to installation instructions #F90752 - Side Panel Support Installation. Otherwise,

proceed to step #4. 4. Position the side panel behind the cabinet side trim. Insure that the panel is fully located behind the side trim and

that the rear flanges of the panel are making contact with the rear of the unit. If necessary, use a shim between the panel and the floor to maintain panel at proper height. Align the top of the panel with the top of the side trim. (figure 1)

5. Using the panel hole locations as a template, drill five (5) holes on the cabinet rear with a 9/64" (.36cm) diameter drill bit. (figure 2)

6. Attach the panel to the rear of the unit using the five (5) black #8 sheet metal screws provided. 7. To attach another side panel, repeat 1-5 above. 8. Install the unit into the opening following the installation instructions provided with the unit.

VIKING 111 Front Street Greenwood, Mississippi 38930 USA (662) 455-1200

Specifications subject to change without notice For more product information, call 1-888-VIKING1 (845-4641), or visit our web site at http://w

Manualsnet FAQs

If you want to find out how the DDSB542 Viking works, you can view and download the Viking DDSB542 Refrigerator Side Panel Kit Instructions on the Manualsnet website.

Yes, we have the Side Panel Kit Instructions for Viking DDSB542 as well as other Viking manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Side Panel Kit Instructions should include all the details that are needed to use a Viking DDSB542. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Viking DDSB542 Refrigerator Side Panel Kit Instructions is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Viking DDSB542 Refrigerator Side Panel Kit Instructions consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Viking DDSB542 Refrigerator Side Panel Kit Instructions free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Viking DDSB542 Refrigerator Side Panel Kit Instructions, simply download the document to your computer. Once downloaded, open the PDF file and print the Viking DDSB542 Refrigerator Side Panel Kit Instructions as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.