Viking DFRB304 Refrigerator Installation Guide PDF

Viking Range Corporation

111 Front Street

Greenwood, Mississippi 38930 USA

(662) 455-1200

For product information,

call 1-888-VIKING1 (845-4641)

or visit the Viking Web site at

vikingrange.com

Viking Installation Guide

F20418B EN (060508J)

Custom Front Models All Refrigerator/Freezer/Side-by-Side/Bottom MountULCUL

Table of Contents Warnings and Important Information Bottom Mount

Dimensions (36) Specifications (36) Cutout Dimensions (36) Anti-Tip Dimensions (36) Overlay Dimensions (36) Custom Grille Dimensions (36) Custom Grille Dimensions (Dual 36)

Side-By-Side Dimensions (42) Dimensions (48) Specifications (42and 48) Cutout Dimensions (42) Anti-Tip Dimensions (42) Cutout Dimensions (48) Anti-Tip Dimensions (48) Overlay Dimensions (42) Overlay Dimensions (48) Custom Grille Dimensions (42) Custom Grille Dimensions (48)

All Refrigerator/Freezer Dimensions (30and 36) Specifications (30and 36) Cutout Dimensions (30) Anti-Tip Dimensions (30) Cutout Dimensions (36) Anti-Tip Dimensions (36) Dimensions (Dual 30) Dimensions (Dual 30and 36) Dimensions (Dual 36and 36) Specifications (Dual) Cutout Dimensions (Dual 30) Anti-Tip Dimensions (Dual 30) Cutout Dimensions (Dual 30and 36) Anti-Tip Dimensions (Dual 30and 36) Cutout Dimensions (Dual 36) Anti-Tip Dimensions (Dual 36) Overlay Dimensions (30and 36) Custom Grille Dimensions (30) Custom Grille Dimensions (36) Custom Grille Dimensions (Dual 30) Custom Grille Dimensions (Dual 30and 36) Custom Grille Dimensions (Dual 36)

Cabinet Information Custom Side Panel Dimensions Custom Panel General Information Ice and Water Dispenser Bezel Removal Custom Door Panel InstallationRefrigerator Custom Door Panel InstallationFreezer Ice and Water Dispenser Bezel Installation Custom Panel Hinge Cutout Custom Grille Installation General Information Unpacking & Moving Installation Hinge Adjustment Kickplate Installation Door Stop Adjustment Water Filter Installation Water Filter System Specifications Final Installation Performance Checklist Control Panels Service & Registration

2

2

3 4 5 6 7 8 9

10 11 12 13 14 15 16 17 18 19 20

21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43

46 46 48 49 50 52 53 55 57 58 59 61 62 63 64 65 66 67 69

IMPORTANTPlease Read and Follow Make sure that incoming voltage is the same as unit rating. An electric rating plate specifying voltage, frequency, wattage, amperage, and phase is attached to the product.

To reduce the risk of fire, electrical shock, or injury to persons, installation work and electrical wiring must be done by qualified people in accordance with all applicable codes and standards, including fire-rated construction.

The installer should leave these instructions with the consumer who should retain them for local inspectors use and for future reference.

It is your responsibility to: Comply with installation specifications and dimensions.

Properly install unit. Remove any moldings or decorative panels that prevent the unit from being serviced.

Make sure that you have these materials (not provided with your unit), which are necessary for proper installation:

1/4 (6 mm) copper tubing with shutoff valve

6 #8 x 3 (7.6 cm) wood screws (longer screws may be required)

1 Saddle valve (do not use self-piercing feature of the valve)

Assure that floor will support unit, door panels and contents (approximately 1200 pounds [540 kg]).

Provide a properly grounded electrical outlet. Assure that location will permit appliance doors to open a minimum of 90.

W A R N I N G TIP OVER HAZARD

Appliance is top heavy and tips easily when not completely installed. Keep doors closed until appliance is completely installed and secured per installation instructions.

Use two or more people to move and install appliance. Failure to do so can result in death or serious injury.

ELECTRICAL SHOCK HAZARD Disconnect power or turn power disconnect switch to OFF position before removing top grille. Failure to do so can result in death or electric shock.

Your safety and the safety of others is very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol. This symbol alerts to hazards that can result in injury or death to you and others.

All safety messages will be preceded by the safety alert symbol and the wordDANGER or WARNING. These words mean:

Failure to follow these instructions will result in serious injury or death.

Failure to follow these instructions can result in serious injury or death.

All safety messages will identify the hazard, tell you how to reduce the chance of injury, and tell you what can happen if

the instructions are not followed.

Most of the units weight is at the top. Extra care is needed when moving the unit to prevent tipping. Use cardboard shipping material or plywood under unit until it is installed in the operating position to protect floor surface.

D A N G E R

W A R N I N G

W A R N I N G45

Specifications (Bottom Mount)

4

51-7/8(131.8 cm)

23-1/16(58.6 cm)

3-1/2(8.9 cm)

82-7/8(210.5 cm)min. to84-1/16(213.5 cm)max.

Measurement varies

(locally supplied hardware)

23 13/16

(60.5 cm)

24 3/4

(62.9 cm)

35(98.9 cm)

36(91.4 cm)

Dimensions (Bottom Mount)

3

36 Bottom Mount Description DFBB363 Overall width 36 (91.5 cm) Overall height (from bottom) 82-3/4 (210.2 cm) min. to 84-1/16 (213.5 cm) max. Overall depth (from rear) To front edge of side trim: 23-13/16 (60.5 cm)

To front of top grille: 24-3/4 (62.9 cm) To front edge of door trim: 24 (61.0 cm)

Cutout width 36 (91.5 cm) Cutout height 82-7/8 (210.5 cm) min. to 84-1/16 (213.5 cm) max. Cutout depth 24 (61.0 cm) min.* Electrical requirements 115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with

grounded 3-prong plug attached to product Maximum amp usage 9.9 amps Inlet water 1/4 copper tubing inlet waterline; minimum 20 psi; requirements maximum 120 psi Overall interior dimensions

Refrigerator 15.2 cu. ft. (431 liters) Freezer 5.1 cu. ft. (145 liters) Total capacity 20.3 cu. ft. (576 liters)

Maximum panel weight Fresh food 45 lbs. (20.4 kg) Freezer 20 lbs. (9.0 kg) Approximate shipping weight 500 lbs. (227.3 kg)

*Full overlay models fit flush in 25 (63.5 cm) deep cabinet openings. They can be installed in standard 24 (61.0 cm) deep openings. The door faces and top grille will protrude 3/4 (1.9 cm) into the room.

36 Bottom Mount

65

9(22.9 cm)

73-3/8(186.4 cm)

82-7/8(210.5 cm) min. anti-tip board &opening height

84-1/16(213.5 cm) max. anti-tip board & opening height

36(91.5 cm)

24 (61.0 cm) Electric outlet location

Water line entry area

36(91.5 cm) 6-3/4(17.1 cm)

7-5/8(19.4 cm)

3(7.6 cm)

5/8(1.5 cm)

5/8(1.5 cm)

10-1/2(26.7 cm) 5/8(1.5 cm)

10-3/4(27.3 cm)

1 (2.5 cm)

3-5/8(9.2 cm)

Optional floor

water line entry

See anti-tip board installation 6 (15.2 cm)

9 (22.9 cm)

Cutout Dimensions (Bottom Mount)

36 Bottom Mount

One 2x 4 mounting board 1-1/2 (3.8 cm) x 3-1/2 (8.9 cm)

Note: If unit is installed deeper than 24 (61.0 cm), then shim behind the mounting board by the difference.

Bottom of anti-tip board is 3-7/8 (9.8 cm) below opening height. Note: Top of unit must be placed firmly under anti-tip board.

Anti-tip location

79-3/8(201.6 cm) min.to bottom ofanti-tip board

80-1/2(204.6 cm) max.to bottom ofanti-tip board

29 (73.7 cm)

3-1/2(8.9 cm)

1-1/2

(3.8 cm)

Anti-Tip Dimensions (Bottom Mount)

36 Bottom Mount

Reverse dimensions for other end.

1/2(1.27 cm)

1-1/2

(3.81 cm)

1/4 Radius

(.64 cm)

2-3/4

(6.98 cm)

1/2(1.27 cm)

3/4(1.90 cm)

1/2

(1.27 cm)

1/8(.31 cm)

1/2(1.27 cm)

1/4 Radius

(1.2 cm)

.64

7/8

(2.22 cm)

1/2 (1.27 cm)34(86.36 cm)

34(86.36 cm)

3/4(1.90 cm)

1/2(1.27 cm)

3/4(1.90 cm)

3-3/4

(9.52 cm)

3-3/4

(9.52 cm)

3-5/8

(9.20 cm)

33-15/16 (86.20 cm)

3

(7.62 cm)

3

(7.62 cm)

3/4(1.90 cm)

35-1/2(90.17 cm)

1/2(1.27 cm)

3-1/8

(7.93 cm)

Optional hinge cover

32-3/16(81.75 cm)

5-17/32(14.10 cm)

4-11/64(10.59 cm)

30-27/32 (78.34 cm)

3 25/32 (9.60 cm)

27/32 (.84 cm)

9/16

(1.42 cm)

1/4

(.635 cm)

16.5 20.0

2-1/8(5.4 cm)

Custom Grille Dimensions (Bottom Mount)

8

35-1/4(89.5 cm)

23-1/16(58.6 cm)

3/4

(1.9 cm)

35-1/4(89.5 cm)

34-3/8 to notch (86.6 cm)

7/8(2.2 cm)

5/8(1.6 cm) 51-7/8(131.8 cm)

51-1/4(130.2 cm)

3/4

(1.9 cm)

Note: Corner notch is for left

hinge door. (Reverse for right hinge)

See page 50 for cutout instructions

7/8(2.2cm) 5/8(1.6 cm)

1/8 (0.3 cm)

2(5.1 cm)

For Models made before 9/22/06

Note: Inset shown upside down.

1-13/16 (4.60 cm)

5/8 (1.6 cm)

3(7.62 cm)

3/32

(.24 cm)

For Models made after 9/22/06

Note: Inset shown upside down

Overlay Dimensions (Bottom Mount)

7

36 Custom Panels 36 Custom Grille

Note: Panel overlays must be dry, solid, straight one piece panels. The use of multiple panel pieces to achieve the dimensions is not recommended.

Important: A 1/4 back panel is required. Make it 1/4 smaller in width and 7/8 shorter in height than the dimensions shown. Locate it to achieve a 1/8 inset on the top and both sides and a 3/4 inset on the bottom.

75-15/16 (192.9 cm)

3-1/2(8.9 cm)

82-7/8(210.5 cm)min. to84-1/16(213.5 cm)max.

Measurement varies

(locally supplied hardware)

23-13/16

(60.5 cm)

24-3/4

(62.9 cm)

41(104.1 cm)

42(106.7 cm)

Dimensions (Side-By-Side)

10

3 25/32 (9.60 cm)

27/32 (.84 cm)

9/16

(1.42 cm)

1/4

(.635 cm)

16.5 20.0

Note: This part should be located at the center of the grille. If desired, two per grille can be used by dividing the length of the grille into thirds.

1/2(1.27 cm)

1-1/2

(3.81 cm)

1/4 Radius

(.64 cm)

2-3/4

(6.98 cm)

1/2(1.27 cm)

3/4(1.90 cm)

3/8 (0.38 cm)

1/2 (1.27 cm)

R 3/32 (0.09 cm)

3/4 (1.90 cm)

3/4 (1.90 cm)

3/4 (1.90 cm)

13/32 (1.03 cm)

9/16 (1.43 cm)

1/8 (.32 cm)

Grille support

2-7/8(7.30 cm)

1(2.54 cm)

1/2

(1.27 cm)

1/8(.31 cm)

1/2(1.27 cm)

1/4 Radius

(1.2 cm)

.64

Reverse dimensions for other end.

7/8

(2.22 cm)

1/2 (1.27 cm)

1/2(1.27 cm) 3-1/8

(7.93 cm)

Optional hinge cover

1/2(1.27 cm)

3-5/8

(9.20 cm)

3/4(1.90 cm)

3/4(1.90 cm)

3-3/4

(9.52 cm)

3-3/4

(9.52 cm)

3

(7.62 cm)

3

(7.62 cm)

3/4(1.90 cm)

71-1/2(181.61 cm)

70(177.80 cm

69-15/16 (177.64 cm)

70(177.80 cm)

68-3/64 (172.83 cm)

66-27/32 (169.78 cm)

4-11/64(11.27 cm)

5-17/32(14.04 cm) 30-27/32 (78.34 cm)

32-3/16(81.75 cm)

40-11/64 (102.03 cm)

41-25/64 (10 5.13 cm)

Custom Grille Dimensions (Bottom Mount)

9

Dual 36 Custom Grille 42 Side-By-Side

Specifications (Side-By-Side)

12

75-15/16 (192.9 cm)

3-1/2(8.9 cm)

82-7/8(210.5 cm)min. to84-1/16(213.5 cm)max.

23-13/16

(60.5 cm)

24-3/4

(62.9 cm)

47(119.4 cm)

48(121.9 cm)

Measurement varies

(locally supplied hardware)

Dimensions (Side-By-Side)

11

42 Side-By-Side Description DFSB423 DFSB423D Overall width 42 (106.7 cm) Overall height (from bottom) 82-3/4 (210.2 cm) min. to 84-1/16 (213.5 cm) max. Overall depth (from rear) To front edge of side trim: 23-13/16 (60.5 cm)

To front of top grille: 24-3/4 (62.9 cm) To front edge of door trim: 24 (61.0 cm)*

Cutout width 42 (106.7 cm) Cutout height 82-7/8 (210.5 cm) min. to 84-1/16 (213.5 cm) max. Cutout depth 24 (61.0 cm) min.* Electrical requirements 115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with

grounded 3-prong plug attached to product Maximum amp usage 9.9 amps Inlet water 1/4 copper tubing inlet waterline; 1/4 copper tubing inlet waterline; requirements minimum 20 psi; maximum 120 psi minimum 35 psi; maximum 120 psi Overall interior dimensions Refrigerator 15.0 cu. ft. (425 liters) 14.5 cu. ft. (411 liters) Freezer 9.0 cu. ft. (255 liters) 8.6 cu. ft. (244 liters) Total capacity 24.0 cu. ft. (680 liters) 23.1 cu. ft. (654 liters)

Maximum panel weight Fresh food 40 lbs. (18.1 kg) Freezer 35 lbs. (15.9 kg) Approximate shipping weight 525 lbs. (236.2 kg)

48 Side-By-Side Description DFSB483 DFSB483D Overall width 48 (121.9 cm) Overall height (from bottom) 82-3/4 (210.2 cm) min. to 84-1/16 (213.5 cm) max. Overall depth (from rear) To front edge of side trim: 23-13/16 (60.5 cm)

To front of top grille: 24-3/4 (62.9 cm) To front edge of door trim: 24 (61.0 cm)*

Cutout width 48 (121.9 cm) Cutout height 82-7/8 (210.5 cm) min. to. 84-1/16 (213.5 cm) max Cutout depth 24 (61.0 cm) min.* Electrical requirements 115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with

grounded 3-prong plug attached to product Maximum amp usage 9.9 amps Inlet water 1/4 copper tubing inlet waterline; 1/4 copper tubing inlet waterline; requirements minimum 20 psi; maximum 120 psi minimum 35 psi; maximum 120 psi Overall interior dimensions Refrigerator 18.5 cu. ft. (524 liters) 17.9 cu. ft. (507 liters) Freezer 8.9 cu. ft. (252 liters) 8.5 cu. ft. (241 liters) Total capacity 27.4 cu. ft. (776 liters) 26.4 cu. ft. (748 liters)

Maximum panel weight Fresh food 50 lbs. (22.7 kg) Freezer 35 lbs. (15.9 kg) Approximate shipping weight 650 lbs. (292.5 kg)

*Full overlay models fit flush in 25 (63.5 cm) deep cabinet openings. They can be installed in standard 24 (61.0 cm) deep openings. The door faces and top grille will protrude 3/4 (1.9 cm) into the room.

48 Side-By-Side

1413

One 2x 4 mounting board 1-1/2 (3.8 cm) x 3-1/2 (8.9 cm)

Note: If unit is installed deeper than 24 (61.0 cm), then shim behind the mounting board by the difference.

Bottom of anti-tip board is 3-7/8 (9.8 cm) below opening height. Note: Top of unit must be placed firmly under anti-tip board.

Anti-tip location

79-3/8(201.6 cm) min.to bottom ofanti-tip board

80-1/2(204.6 cm) max.to bottom ofanti-tip board

35 (88.9 cm)

3-1/2(8.9 cm)

1-1/2

(3.8 cm)

Anti-Tip Dimensions (Side-By-Side)

9(22.9 cm)

73-3/8(186.4 cm)

82-7/8(210.5 cm) min. anti-tip board &opening height

84-1/16(213.5 cm) max. anti-tip board & opening height

42(106.7 cm)

24 (61.0 cm)

Electric outlet location

Water line entry area

42(106.7 cm) 6-3/4(17.1 cm)

7-5/8(19.4 cm)

3(7.6 cm)

5/8(1.5 cm)

5/8(1.5 cm)

10-1/2(26.7 cm) 5/8(1.5 cm)

10-3/4(27.3 cm)

1 (2.5 cm)

3-5/8(9.2 cm)

Optional floor

water line entry

See anti-tip board installation 6

(15.2 cm)

9 (22.9 cm)

Cutout Dimensions (Side-By-Side)

42 Side-By-Side 42 Side-By-Side

1615

One 2x 4 mounting boards 1-1/2 (3.8 cm) x 3-1/2 (8.9 cm)

Note: If unit is installed deeper than 24 (61.0 cm), then shim behind the mounting board by the difference.

Bottom of anti-tip board is 3-7/8 (9.8 cm) below opening height. Note: Top of unit must be placed firmly under anti-tip board.

Anti-tip location

79-3/8(201.6 cm) min.to bottom ofanti-tip board

80-1/2(204.6 cm) max.to bottom ofanti-tip board

41(104.1 cm)

3-1/2(8.9 cm)

1-1/2

(3.8 cm)

Anti-Tip Dimensions (Side-By-Side)

9(22.9 cm)

73-3/8(186.4 cm)

827/8(210.5 cm) min. anti-tip board &opening height

841/16(213.5 cm) max. anti-tip board & opening height

48(121.9 cm)

24 (61.0 cm)

Electric outlet location

Water line entry area

47-1/2(120.7 cm) 6-3/4(17.1 cm)

7-5/8(19.4 cm)

3(7.6 cm)

5/8(1.5 cm)

5/8(1.5 cm)

10-1/2(26.7 cm) 5/8(1.5 cm)

10-3/4(27.3 cm)

1 (2.5 cm)

3-5/8(9.2 cm)

Optional floor

water line entry

See anti-tip board installation 6

(15.2 cm)

9 (22.9 cm)

Cutout Dimensions (Side-By-Side)

48 Side-By-Side 48 Side-By-Side

28-5/16(71.9 cm)

75-1/2(191.8 cm)

3/4

(1.9 cm)

18-11/16 (47.5 cm)

3/4

(1.9 cm)

28-5/16(71.9 cm)

75-1/2(191.8 cm)

3/4

(1.9 cm)

18-11/16 (47.5 cm)

31-5/8(80.3 cm) 10-11/16 (27.1 cm)

12-3/8(31.4 cm)

3/4

(1.9 cm)

3-5/32(8.0 cm)

Overlay Dimensions (Side-By-Side)

18

22-13/16 (57.9 cm)

75-1/2(191.8 cm)

3/4

(1.9 cm)

3/4

(1.9 cm) 18-3/16(46.2 cm)

22-13/16 (57.9 cm)

75-1/2(191.8 cm)

3/4

(1.9 cm)

18-3/16(46.2 cm)

31-5/8(80.3 cm) 10-11/16 (27.1 cm)

12-3/8(31.4 cm)

3/4

(1.9 cm)

3-5/32(8.0 cm)

Overlay Dimensions (Side-By-Side)

17

42 Custom Panels

42 Custom Panels with Dispenser

48 Custom Panels

48 Custom Panels with Dispenser

Note: Panel overlays must be dry, solid, straight one piece panels. The use of multiple panel pieces to achieve the dimensions is not recommended.

Important: A 1/4 thick back panel is required. Make it 1/4 smaller than the dimensions shown. Locate it to achieve a 1/8 inset on all sides.

Note: Panel overlays must be dry, solid, straight one piece panels. The use of multiple panel pieces to achieve the dimensions is not recommended.

Important: A 1/4 thick back panel is required. Make it 1/4 smaller than the dimensions shown. Locate it to achieve a 1/8 inset on all sides.

1/2

(1.27 cm)

1/8(.31 cm)

1/2(1.27 cm)

1/4 Radius

(1.2 cm)

.64

Reverse dimensions for other end.

7/8

(2.22 cm)

1/2 (1.27 cm)

2-1/8

(5.39 cm)

3-1/8

(7.94 cm)3-5/8 (9.20 cm)

1-3/8 (3.49 cm)

3/8

(.95 cm)

3/8 Radius (.95 cm)

47-1/2(120.65 cm)

1/2(1.27 cm)

3-1/8

(7.93 cm)

Optional hinge cover

46(116.84 cm)

1/2(1.27 cm)

3-5/8

(9.20 cm)

45-15/16 (116.68 cm)

46(116.84 cm)

3/4(1.90 cm)

3/4(1.90 cm)

3-3/4

(9.52 cm)

3-3/4

(9.52 cm)

3

(7.62 cm)

3

(7.62 cm)

3/4(1.90 cm)

30-27/32 (78.34 cm)

32-3/16(81.75 cm)

11-17/32 (29.28 cm)

10-11/64 (15.84 cm)

1/2(1.27 cm)

1-1/2

(3.81 cm)

1/4 Radius

(.64 cm)

2-3/4

(6.98 cm)

1/2(1.27 cm)

3/4(1.90 cm)

Custom Grille Dimensions (Side-By-Side)

20

1/2(1.27 cm)

1-1/2

(3.81 cm)

1/4 Radius

(.64 cm)

2-3/4

(6.98 cm)

1/2(1.27 cm)

3/4(1.90 cm)

1/2

(1.27 cm)

1/8(.31 cm)

1/2(1.27 cm)

1/4 Radius

(1.2 cm)

.64

Reverse dimensions for other end.

7/8

(2.22 cm)

1/2 (1.27 cm)

2-1/8

(5.39 cm)

3-1/8

(7.94 cm)3-5/8 (9.20 cm)

1-3/8 (3.49 cm)

3/8

(.95 cm)

3/8 Radius (.95 cm)

41-1/2(105.41 cm)

1/2(1.27 cm)

3-1/8

(7.93 cm)

Optional hinge cover

40(101.60 cm)

40(101.60 cm)

3/4(1.90 cm)

3/4(1.90 cm)

3-1/4

(9.52 cm)

3-3/4

(9.52 cm)

1/2(1.27 cm)

3-5/8

(9.20 cm)

39-15/16 (101.44 cm)

3

(7.62 cm)

3

(7.62 cm)

3/4(1.90 cm)

24-27/32 (63.10 cm)

26-3/16(66.51 cm)

5-17/32(14.04 cm)

4-11/64(10.60 cm)

Custom Grille Dimensions (Side-By-Side)

19

42 Custom Grille 48 Custom Grille

22

35(88.9 cm)

23-13/16

(60.4 cm)

24-3/4

(62.9 cm)

82-7/8(210.5 cm)min. to84-15/16

(213.5 cm)max.

82-7/8(210.5 cm)min. to84-1/16(213.5 cm)max. 75-15/16

(192.9 cm)

3-1/2(8.9 cm)

75-15/16 (192.9 cm)

3-1/2(8.9 cm)

36(91.5 cm)

Measurement varies

(locally supplied hardware)

Measurement varies

(locally supplied hardware)

30(76.2 cm)

29(73.7 cm)

23-13/16

(60.4 cm)

24-3/4

(62.9 cm)

Dimensions (All Refrigerator/Freezer)

21

Specifications (All Refrigerator/Freezer)

30 All Refrigerator/Freezer Description DFFB304 DFRB304 Overall width 30 (76.2 cm) Overall height (from bottom) 82-3/4 (210.2 cm) min. to 84-1/16 (213.5 cm) max. Overall depth (from rear) To front edge of side trim: 23-13/16 (60.5 cm)

To front of top grille: 24-3/4 (62.9 cm) To front edge of door trim: 24 (61.0 cm)

Cutout width 30 (76.2 cm) Cutout height 82-7/8 (210.5 cm) min. to 84-1/16 (213.5 cm) max. Cutout depth 24 (61.0 cm) min.* Electrical requirements 115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with

grounded 3-prong plug attached to product Maximum amp usage 9.9 amps Inlet water 1/4 copper tubing inlet requirements waterline; minimum 20 psi; N/A

maximum 120 psi Overall interior dimensions total capacity 15.9 cu. ft. (450 liters) 18.2 cu. ft. (516 liters) Maximum panel weight 50 lbs. (22.7 kg)

Approximate shipping weight 425 lbs. (193.2 kg)

36 All Refrigerator/Freezer Description DFFB364 DFRB364 Overall width 36 (91.5 cm) Overall height (from bottom) 82-3/4 (210.2 cm) min. to 84-1/16 (213.5 cm) max. Overall depth (from rear) To front edge of side trim: 23-13/16 (60.5 cm)

To front of top grille: 24-3/4 (62.9 cm) To front edge of door trim: 24 (61.0 cm)

Cutout width 36 (91.5 cm) Cutout height 82-7/8 (210.5 cm) min. to 84-1/16 (213.5 cm) max. Cutout depth 24 (61.0 cm) min.* Electrical requirements 115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with

grounded 3-prong plug attached to product Maximum amp usage 9.9 amps Inlet water 1/4 copper tubing inlet requirements waterline; minimum 20 psi; N/A

maximum 120 psi Overall interior dimensions total capacity 19.1 cu. ft. (541 liters) 22.8 cu. ft. (646 liters) Maximum panel weight 60 lbs. (27.2 kg)

Approximate shipping weight 500 lbs. (227.3 kg)

30 All Refrigerator/Freezer

36 All Refrigerator/Freezer

*Full overlay models fit flush in 25 (63.5 cm) deep cabinet openings. They can be installed in standard 24 (61.0 cm) deep openings. The door faces and top grille will protrude 3/4 (1.9 cm) into the room.

One 2x 4 mounting board 1-1/2 (3.8 cm) x 3-1/2 (8.9 cm)

Note: If unit is installed deeper than 24 (61.0 cm), then shim behind the mounting boards by the difference.

Bottom of anti-tip board is 3-7/8 (9.8 cm) below opening height. Note: Top of unit must be placed firmly under anti-tip board.

Anti-tip location

79-3/8(201.6 cm) min.to bottom ofanti-tip board

80-1/2(204.6 cm) max.to bottom ofanti-tip board

23 (58.4 cm)

3-1/2(8.9 cm)

1-1/2

(3.8 cm)

24

9(22.9 cm)

73-3/8(186.4 cm)

82-7/8(210.5 cm) min. anti-tip board &opening height

84-1/16(213.5 cm) max. anti-tip board & opening height

30(76.2 cm)

24 (61.0 cm) Electric outlet location

Water line entry area Note: shown for All Freezer only

30(76.2 cm) 6-3/4(17.1 cm)

7-5/8(19.4 cm)

3(7.6 cm) 5/8(1.5 cm)

5/8(1.5 cm)

10-1/2(26.7 cm) 5/8(1.5 cm)

10-3/4(27.3 cm)

1 (2.5 cm)

3-5/8(9.2 cm)

Optional floor

water line entry

See anti-tip board installation 6 (15.2 cm)

9 (22.9 cm)

23

Cutout Dimensions (All Refrigerator/Freezer)

30 All Refrigerator/Freezer

Anti-Tip Dimensions (All Refrigerator/Freezer)

30 All Refrigerator/Freezer

One 2x 4 mounting voard 1-1/2 (3.8 cm) x 3-1/2 (8.9 cm)

Note: If unit is installed deeper than 24 (61.0 cm), then shim behind the mounting boards by the difference.

Bottom of anti-tip board is 3-7/8 (9.8 cm) below opening height. Note: Top of unit must be placed firmly under anti-tip board.

Anti-tip location

79-3/8(201.6 cm) min.to bottom ofanti-tip board

80-1/2(204.6 cm) max.to bottom ofanti-tip board

29 (73.7 cm)

3-1/2(8.9 cm)

1-1/2

(3.8 cm)

26

9(22.9 cm)

73-3/8(186.4 cm)

82-7/8(210.5 cm) min. anti-tip board &opening height

84-1/16(213.5 cm) max. anti-tip board & opening height

36(91.5 cm)

24 (61.0 cm) Electric outlet location

Water line entry area Note: shown for All Freezer only

36(91.5 cm) 6-3/4(17.1 cm)

7-5/8(19.4 cm)

3(7.6 cm)

5/8(1.5 cm)

5/8(1.5 cm)

10-1/2(26.7 cm) 5/8(1.5 cm)

10-3/4(27.3 cm)

1 (2.5 cm)

3-5/8(9.2 cm)

Optional floor

water line entry

See anti-tip board installation 6 (15.2 cm)

9 (22.9 cm)

25

Cutout Dimensions (All Refrigerator/Freezer)

36 All Refrigerator/Freezer

Anti-Tip Dimensions (All Refrigerator/Freezer)

36 All Refrigerator/Freezer

75-15/16 (192.9 cm)

3-1/2(8.9 cm) 30(76.2 cm)

29(73.7 cm)

29-1/2(74.9 cm)

1(2.54 cm) between units

35(88.9 cm)

82-7/8(210.5 cm)min. to84-15/16

(213.5 cm)max.

36(91.5 cm)

Measurement varies

(locally supplied hardware)

23-13/16

(60.5 cm)

24-3/4

(62.9 cm)

35-1/2(90.2 cm)

Dimensions (All Refrigerator/Freezer)

28

23-13/16

(60.5 cm)

24-3/4

(62.9 cm)

82-7/8(210.5 cm)min. to84-15/16

(213.5 cm)max.

Measurement varies

(locally supplied hardware)

30(76.2 cm)

29(73.7 cm)

75-15/16 (192.9 cm)

3-1/2(8.9 cm) 30(76.2 cm)

29(73.7 cm)

29-1/2(74.9 cm)

29-1/2(74.9 cm)

1(2.54 cm) between units

Dimensions (All Refrigerator/Freezer)

27

Dual 30 All Refrigerator/Freezer Dual 30 and 36 All Refrigerator/Freezer

Specifications (All Refrigerator/Freezer)

30

75-15/16 (192.9 cm)

3-1/2(8.9 cm)

1(2.54 cm) between units

35(88.9 cm)

82-7/8(210.5 cm)min. to84-15/16

(213.5 cm)max.

36(91.5 cm)

Measurement varies

(locally supplied hardware)

23-13/16

(60.5 cm)

24-3/4

(62.9 cm)

35-1/2(90.2 cm)

35-1/2(90.2 cm)

35(88.9 cm)

36(91.5 cm)

Dimensions (All Refrigerator/Freezer)

29

Dual All Refrigerator/Freezer Description (2) 30 Units (1) 36 & (1) 30 Unit (2) 36 Units Overall width 60 (152.4 cm) 66 (167.6 cm) 72 (182.9 cm) Overall height (from bottom) 82-3/4 (210.2 cm) min. to 84-1/16 (213.5 cm) max. Overall depth (from rear) To front edge of side trim: 23-13/16 (60.5 cm)

To front of top grille: 24-3/4 (62.9 cm) To front edge of door trim: 24 (61.0 cm)

Cutout width 60 (152.4 cm) 66 (167.6 cm) 72 (182.9 cm) Cutout height 82-7/8 (210.5 cm) min. to 84-1/16 (213.5 cm) max. Cutout depth 24 (61.0 cm) min.* Electrical requirements (2) 115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with

grounded 3-prong plug attached to product Maximum amp usage 9.9 amps per unit Inlet water requirements 1/4 copper tubing inlet waterline; minimum 20 psi; (All Freezer only) maximum 120 psi Overall interior dimensions

30 freezer 15.9 cu. ft. (450 liters) 30 refrigerator 18.2 cu. ft. (516 liters) 36 freezer 19.1 cu. ft. (541 liters) 36 refrigerator 22.8 cu. ft. (646 liters)

Maximum panel weight 30 freezer or refrigerator 50 lbs. (22.7 kg)

36 freezer or refrigerator 60 lbs. (27.2 kg)

Approximate shipping weight 30 freezer or refrigerator 425 lbs. (193.2 kg) 36 freezer or refrigerator 500 lbs. (227.3 kg)

Dual 36 All Refrigerator/Freezer

*Full overlay models fit flush in 25 (63.5 cm) deep cabinet openings. They can be installed in standard 24 (61.0 cm) deep openings. The door faces and top grille will protrude 3/4 (1.9 cm) into the room.

79-3/8(201.6 cm) min.to bottom ofanti-tip board

80-1/2(204.6 cm) max.to bottom ofanti-tip board

One 2x 4 mounting board per unit 1-1/2 (3.8 cm) x 3-1/2 (8.9 cm)

Note: If unit is installed deeper than 24 (61.0 cm), then shim behind the mounting boards by the difference.

Bottom of anti-tip board is 3-7/8 (9.8 cm) below opening height. Note: Top of unit must be placed firmly under anti-tip board.

Anti-tip location

23 (58.4 cm)

3-1/2(8.9 cm)

1-1/2

(3.8 cm)

23 (58.4 cm)

32

9(22.9 cm)

73-3/8(186.4 cm)

82-7/8(210.5 cm) min. anti-tip board &opening height

84-1/16(213.5 cm) max. anti-tip board & opening height

60(152.4 cm)

24 (61.0 cm) Electric outlet location

Water line entry area Note: Cutout opening shown with All Freezer model on left.

Reverse water line entry if All Freezer model is on right.

60(152.4 cm) 6-3/4(17.1 cm)

7-5/8(19.4 cm) 3(7.6 cm)

5/8(1.5 cm)

5/8(1.5 cm)

10-1/2(26.7 cm) 5/8(1.5 cm)

10-3/4(27.3 cm)

3-5/8(9.2 cm)

Optional floor

water line entry

1 (2.5 cm)

See anti-tip board installation 6

(15.2 cm)

9 (22.9 cm)

31

Cutout Dimensions (All Refrigerator/Freezer)

Dual 30 All Refrigerator/Freezer

Anti-Tip Dimensions (All Refrigerator/Freezer)

Dual 30 All Refrigerator/Freezer

79-3/8(201.6 cm) min.to bottom ofanti-tip board

80-1/2(204.6 cm) max.to bottom ofanti-tip board

One 2x 4 mounting board per unit 1-1/2 (3.8 cm) x 3-1/2 (8.9 cm)

Note: If unit is installed deeper than 24 (61.0 cm), then shim behind the mounting boards by the difference.

Bottom of anti-tip board is 3-7/8 (9.8 cm) below opening height. Note: Top of unit must be placed firmly under anti-tip board.

Note: Dimensions shown for 36 All Freezer/All Refrigerator model on the left. Reverse mounting boards if units are installed on the right.

Anti-tip location

29 (73.7 cm)

3-1/2(8.9 cm)

1-1/2

(3.8 cm)

23 (58.4 cm)

34

9(22.9 cm)

73-3/8(186.4 cm)

82-7/8(210.5 cm) min. anti-tip board &opening height

841/16(213.5 cm) max. anti-tip board & opening height

66(167.6 cm)

24 (61.0 cm) Electric outlet location

Water line entry area Note: Cutout opening shown with All Freezer model on left.

Reverse water line entry if All Freezer model is on right.

66(167.6 cm) 6-3/4(17.1 cm)

7-5/8(19.4 cm) 3(7.6 cm)

5/8(1.5 cm)

5/8(1.5 cm)

10-1/2(26.7 cm) 5/8(1.5 cm)

10-3/4(27.3 cm)

3-5/8(9.2 cm)

Optional floor

water line entry

1 (2.5 cm)

See anti-tip board installation 6

(15.2 cm)

9 (22.9 cm)

33

Cutout Dimensions (All Refrigerator/Freezer)

Dual 30 and 36 All Refrigerator/Freezer

Anti-Tip Dimensions (All Refrigerator/Freezer)

Dual 30 and 36 All Refrigerator/Freezer

79-3/8(201.6 cm) min.to bottom ofanti-tip board

80-1/2(204.6 cm) max.to bottom ofanti-tip board

One 2x 4 mounting board per unit 1-1/2 (3.8 cm) x 3-1/2 (8.9 cm)

Note: If unit is installed deeper than 24 (61.0 cm), then shim behind the mounting boards by the difference.

Bottom of anti-tip board is 3-7/8 (9.8 cm) below opening height. Note: Top of unit must be placed firmly under anti-tip board.

Anti-tip location

29 (73.7 cm)

3-1/2(8.9 cm)

1-1/2

(3.8 cm)

29 (73.7 cm)

Anti-Tip Dimensions (All Refrigerator/Freezer)

36

9(22.9 cm)

73-3/8(186.4 cm)

82-7/8(210.5 cm) min. anti-tip board &opening height

84-1/16(213.5 cm) max. anti-tip board & opening height

72(182.9 cm)

24 (61.0 cm) Electric outlet location

Water line entry area Note: Cutout opening shown with All Freezer model on left.

Reverse water line entry if All Freezer model is on right.

72(182.9 cm) 63/4(17.1 cm)

7-5/8(19.4 cm) 3(7.6 cm)

5/8(1.5 cm)

5/8(1.5 cm)

10-1/2(26.7 cm) 5/8(1.5 cm)

10-3/4(27.3 cm)

3-5/8(9.2 cm)

Optional floor

water line entry

1 (2.5 cm)

See anti-tip board installation 6

(15.2 cm)

9 (22.9 cm)

Cutout Dimensions (All Refrigerator/Freezer)

35

Dual 36 All Refrigerator/Freezer Dual 36 All Refrigerator/Freezer

1/2(1.27 cm)

1-1/2

(3.81 cm)

1/4 Radius

(.64 cm)

2-3/4

(6.98 cm)

1/2(1.27 cm)

3/4(1.90 cm)

1/2

(1.27 cm)

1/8(.31 cm)

1/2(1.27 cm)

1/4 Radius

(1.2 cm)

.64

Reverse dimensions for other end.

7/8

(2.22 cm)

1/2 (1.27 cm)

2-1/8

(5.39 cm)

3-1/8

(7.94 cm)3-5/8 (9.20 cm)

1-3/8 (3.49 cm)

3/8

(.95 cm)

3/8 Radius (.95 cm)

29-1/2(74.93 cm)

1/2(1.27 cm)

3-1/8

(7.93 cm)

Optional hinge cover

1/2(1.27 cm)

3-5/8

(9.20 cm)

27-15/16 (70.96 cm)

28(71.12 cm)

28(71.12 cm)

3/4(1.90 cm)

3/4(1.90 cm)

3-3/4

(9.52 cm)

3-3/4

(9.52 cm)

3

(7.62 cm)

3

(7.62 cm)

3/4(1.90 cm) 26-3/16(66.51 cm)

5-17/32(14.10 cm)

4-11/64(10.59 cm)

24-27/32 (63.10 cm)

Custom Grille Dimensions (All Refrigerator/Freezer)

38

35-1/4(89.5 cm)

75-1/2(191.8 cm)

3/4

(1.9 cm)

29-1/4(74.3 cm)

75-1/2(191.8 cm)

3/4

(1.9 cm)

Overlay Dimensions (All Refrigerator/Freezer)

37

30 Custom Panels

36 Custom Panels

30 Custom Grille

Note: Hardware placement can vary depending on single or dual installation.

Note: Panel overlays must be dry, solid, straight one piece panels. The use of multiple panel pieces to achieve the dimensions is not recommended.

Important: A 1/4 thick back panel is required. Make it 1/4 smaller than the dimensions shown. Locate it to achieve a 1/8 inset on all sides.

Note: This part should be located at the center of the grille. If desired, two per grille can be used by dividing the length of the grille into thirds.

1/2(1.27 cm)

1-1/2

(3.81 cm)

1/4 Radius

(.64 cm)

2-3/4

(6.98 cm)

1/2(1.27 cm)

3/4(1.90 cm)

3/8 (0.38 cm)

1/2 (1.27 cm)

R 3/32 (0.09 cm)

3/4 (1.90 cm)

3/4 (1.90 cm)

3/4 (1.90 cm)

13/32 (1.03 cm)

9/16 (1.43 cm)

1/8 (.32 cm)

Grille support

2-7/8(7.30 cm)

1(2.54 cm)

1/2

(1.27 cm)

1/8(.31 cm)

1/2(1.27 cm)

1/4 Radius

(1.2 cm)

.64

Reverse dimensions for other end.

7/8

(2.22 cm)

1/2 (1.27 cm)

2-1/8

(5.39 cm)

3-1/8

(7.94 cm)3-5/8 (9.20 cm)

1-3/8 (3.49 cm)

3/8

(.95 cm)

3/8 Radius (.95 cm)

1/2(1.27 cm)

3-1/8

(7.93 cm)

Optional hinge cover

1/2(1.27 cm)

3-5/8

(9.20 cm)

3/4(1.90 cm)

3/4(1.90 cm)

3-3/4

(9.52 cm)

3-3/4

(9.52 cm)

3

(7.62 cm)

3

(7.62 cm)

3/4(1.90 cm)

59-1/2(151.13 cm)

58(147.32 cm)

57-15/16 (147.16 cm)

58(147.32 cm)

56-3/64 (142.36 cm)

54-27/32 (139.30 cm)

4-11/64(11.27 cm)

5-17/32(14.04 cm) 24-27/32 (63.01 cm)

26-3/16(66.80 cm)

34-11/64 (86.80 cm)

35-25/64 (89.90 cm)

Custom Grille Dimensions (All Refrigerator/Freezer)

40

2-1/8

(5.39 cm)

3-1/8

(7.94 cm)3-5/8 (9.20 cm)

1-3/8 (3.49 cm)

3/8

(.95 cm)

3/8 Radius (.95 cm)

Reverse dimensions for other end.

1/2(1.27 cm)

1-1/2

(3.81 cm)

1/4 Radius

(.64 cm)

2-3/4

(6.98 cm)

1/2(1.27 cm)

3/4(1.90 cm)

1/2

(1.27 cm)

1/8(.31 cm)

1/2(1.27 cm)

1/4 Radius

(1.2 cm)

.64

7/8

(2.22 cm)

1/2 (1.27 cm)34(86.36 cm)

34(86.36 cm)

3/4(1.90 cm)

1/2(1.27 cm)

3/4(1.90 cm)

3-3/4

(9.52 cm)

3-3/4

(9.52 cm)

3-5/8

(9.20 cm)

33-15/16 (86.20 cm)

3

(7.62 cm)

3

(7.62 cm)

3/4(1.90 cm)

35-1/2(90.17 cm)

1/2(1.27 cm)

3-1/8

(7.93 cm)

Optional hinge cover

32-3/16(81.75 cm)

5-17/32(14.10 cm)

4-11/64(10.59 cm)

30-27/32 (78.34 cm)

Custom Grille Dimensions (All Refrigerator/Freezer)

39

36 Custom Grille Dual 30 Custom Grille

Note: Dual units can only be made in a left and right hand configuration.

Note: To use a custom grille on a dual installation, you must purchase the center trim kit FCTKSS.

Note: This part should be located at the center of the grille. If desired, two per grille can be used by dividing the length of the grille into thirds.

1/2(1.27 cm)

1-1/2

(3.81 cm)

1/4 Radius

(.64 cm)

2-3/4

(6.98 cm)

1/2(1.27 cm)

3/4(1.90 cm)

3/8 (0.38 cm)

1/2 (1.27 cm)

R 3/32 (0.09 cm)

3/4 (1.90 cm)

3/4 (1.90 cm)

3/4 (1.90 cm)

13/32 (1.03 cm)

9/16 (1.43 cm)

1/8 (.32 cm)

Grille support

2-7/8(7.30 cm)

1(2.54 cm)

1/2

(1.27 cm)

1/8(.31 cm)

1/2(1.27 cm)

1/4 Radius

(1.2 cm)

.64

Reverse dimensions for other end.

7/8

(2.22 cm)

1/2 (1.27 cm)

2-1/8

(5.39 cm)

3-1/8

(7.94 cm)3-5/8 (9.20 cm)

1-3/8 (3.49 cm)

3/8

(.95 cm)

3/8 Radius (.95 cm)

1/2(1.27 cm)

3-1/8

(7.93 cm)

Optional hinge cover

1/2(1.27 cm)

3-5/8

(9.20 cm)

3/4(1.90 cm)

3/4(1.90 cm)

3-3/4

(9.52 cm)

3-3/4

(9.52 cm)

3

(7.62 cm)

3

(7.62 cm)

3/4(1.90 cm)

71-1/2(181.61 cm)

70(177.80 cm

69-15/16 (177.64 cm)

70(177.80 cm)

68-3/64 (172.84 cm)

66-27/32 169.78 cm)

4-11/64(11.27 cm)

5-17/32(14.04 cm) 30-27/32 (78.34 cm)

32-3/16(81.75 cm)

40-11/64 (102.04 cm)

41-25/64 (105.13 cm)

Custom Grille Dimensions (All Refrigerator/Freezer)

42

Note: This part should be located at the center of the grille. If desired, two per grille can be used by dividing the length of the grille into thirds.

1/2(1.27 cm)

1-1/2

(3.81 cm)

1/4 Radius

(.64 cm)

2-3/4

(6.98 cm)

1/2(1.27 cm)

3/4(1.90 cm)

3/8 (0.38 cm)

1/2 (1.27 cm)

R 3/32 (0.09 cm)

3/4 (1.90 cm)

3/4 (1.90 cm)

3/4 (1.90 cm)

13/32 (1.03 cm)

9/16 (1.43 cm)

1/8 (.32 cm)

Grille support

2-7/8(7.30 cm)

1(2.54 cm)

1/2

(1.27 cm)

1/8(.31 cm)

1/2(1.27 cm)

1/4 Radius

(1.2 cm)

.64

Reverse dimensions for other end.

7/8

(2.22 cm)

1/2 (1.27 cm)

2-1/8

(5.39 cm)

3-1/8

(7.94 cm)3-5/8 (9.20 cm)

1-3/8 (3.49 cm)

3/8

(.95 cm)

3/8 Radius (.95 cm)

1/2(1.27 cm)

3-1/8

(7.93 cm)

Optional hinge cover

1/2(1.27 cm)

3-5/8

(9.20 cm)

3/4(1.90 cm)

3/4(1.90 cm)

3-3/4

(9.52 cm)

3-3/4

(9.52 cm)

3

(7.62 cm)

3

(7.62 cm)

3/4(1.90 cm)

65-1/2(166.37 cm)

64(162.56 cm)

63-15/16 (167.48 cm)

64(162.56 cm)

62-3/64 (157.60 cm)

60-27/32 (154.54 cm)

4-11/64(11.27 cm)

5-17/32(14.04 cm) 24-27/32 (63.10 cm)

26-3/16(66.51 cm)

34-11/64 (86.80 cm)

35-25/64 (89.90 cm)

Custom Grille Dimensions (All Refrigerator/Freezer)

41

Dual 30 and 36 Custom Grille Dual 36 Custom Grille

Note: Dual units can only be made in a left and right hand configuration.

Note: To use a custom grille on a dual installation, you must purchase the center trim kit FCTKSS.

Note: 30 unit is on left and 36 unit is on right.

Note: Dual units can only be made in a left and right hand configuration.

Note: To use a custom grille on a dual installation, you must purchase the center trim kit FCTKSS.

43

Top View Flush mount cabinet doors

24 (61.0 cm) standard cabinet depth

24-3/4 (62.9 cm)

Wall

3/4 (1.9 cm)

full end panel

Flush

Cabinet doorDoor

3/4 (1.9 cm) overlay panel

1/4 (0.6 cm)

base panel

Cabinet Information

44

Top View

Top View

Door

24 (61.0 cm) standard cabinet depth

25 (63.5 cm)

countertop depth

Wall

3/4 (1.9 cm)

full end panel

Door

Wall

1/4 (.63 cm)

if standard 25 (63.5 cm) standard cabinet

depth is used

3/4 (1.9 cm) full end panel25

(63.5 cm)

Flush

1/4 (.63 cm)

if standard 25 (63.5 cm) standard cabinet

depth is used

Flush

3/4 (1.9 cm) overlay panel

1/4 (0.6 cm)

base panel

3/4 (1.9 cm) overlay panel

1/4 (0.6 cm)

base panel

Cabinet Information Full overlay models, (with 3/4 [1.9 cm], thick panels and custom handles locally supplied), fit flush in 25 (63.5 cm) deep (countertop depth) cabinet openings with no protrusion into room except custom handles

Full overlay models can be installed in standard 24 (61.0 cm) deep openings. However, the door faces and top ventilation grille will protrude 3/4 (1.9 cm) into the room. This is ideal for alignment with full overlay cabinet doors.

3/4 (1.9 cm)

End panel

1 (2.5 cm)

1/4 (0.6 cm)

Z-Bracket

21-3/4

(55.2 cm)

21-3/4

(55.2 cm)

24

(61.0 cm)

Optional kickplate notch Dimensions determined by cabinets 24

(61.0 cm)

82-7/8 (210.5 cm) min.

to84-1/16 (213.5 cm) max.*

82-7/8 (210.5 cm) min.

to84-1/16 (213.5 cm) max.*

Custom Side Panel Dimensions

45

* Depending on how high leveling feet are raised, and cabinet enclosure height.

Note: Adding 3/4 (1.9 cm) side panels adds an additional 3/4 (1.9 cm) to the overall width of the product for each side panel used.

Note: Requires side panel hardware kit (SPHKDS).

46

Ice and Water Dispenser Bezel Removal (if required)

Remove packaging material surrounding bezel. Grasping the sliding lever, pull away from bezel.

Remove spill tray form lower part of bezel exposing two screws.

Remove screws.

1 2

43

Custom Panel General Information

Custom finishing options All installations must allow for the refrigerator ad freezer door to open a minimum of 90. For side wall or corner installation, allow for a standard 3 (7.6 cm) cabinet filler to assure door(s) open 90.

Note: If a custom handle is used a wider filler may be necessary. Panel thickness must not exceed 1 (2.5 cm) on hinge side. Thicker panels will interfere with door swing and clearance.

A 1/4 wood filler or insulation filler must be used between the door and 3/4 wood panel to prevent condensation from forming.

Grasping the bezel on both sides, pull away from the door cavity.

Note: Bezel needs to be pulled from the bottom first and then pull slightly downward to clear

the water dispensing tube.

Store bezel and spill tray in safe and secure place until installation.

7 38

For re-installation steps, see pages 50-51.

Remove two additional screws under top section of bezel.

Remove mounting support.

5 6

47 48

Remove handle side cabinet screws and trim with a phillips screwdriver.

Remove handle side door trim screws and panel with a phillips screwdriver.

Install Z brackets onto back side of custom panels. Note: If 1/4 back panel is used, the brackets will be

flush to the edge (back panel is 1/4 smaller than 3/4 panel dimension).

Proper Z brackets engagement. Note: A 1/4 back panel needs to be used to ensure proper

insulation. If back panel is not used, the potential for condensation is present.

For the last 3 of installation, push evenly on the custom wood panel near the side door trim in addition to pushing from the handle side. This ensures side Z bracket engagement with hinge side door trim.

1 2

3 1/4

off edges of 3/4 panel

1/4 (0.5 cm) back panel

Door

Door trim

Z bracket

3/4 (1.9 cm) custom panel

TOP VIEW

3

4 5

Custom Door Panel Installation (Refrigerator or Freezer)

Align upper and lower Z brackets in door trim and push custom wood panel evenly toward the hinge until

approximately 3 from the hinge side door trim.

49

6

Open freezer door. Remove door trim screws and door trim with a phillips screwdriver.

Install Z brackets onto back side of custom panel. Note: If 1/4 back panel is used, the brackets will be flush to the

edge (back panel is 1/4 smaller than 3/4 panel dimension).

1 2 1/4

off edges of 3/4 panel

Align panel in door trim and push down evenly. Ensure side and bottom Z bracket engagement with door trim.

Reinstall top door trim and door trim screws with a phillips screwdriver.

3 4

Custom Freezer Door Panel Installation (Bottom Mount Only)

Insert handle-side door trim making sure to engage handle-side Z bracket in door trim. Install door trim screws.

7

Reinstall cabinet trim and screws.

50

Install custom wood panels per products installation instructions.

Locate opening in door and position bezel. Note: Graphics on bezel will be on top end, tilt slightly

forward to allow water tube clearance.

Push firmly into cavity until lower screw holes align with mounting holes on cavity.

Install two screws in lower part of bezel but do not tighten all the way.

Position upper mounting support over holes underneath top section of bezel.

Install two screws but do not tighten all the way.

1 2

3 4

5 6

Ice and Water Dispenser Bezel Installation (if required)

51

7 8

Adjust and reposition bezel as necessary. Tighten all screws securely.

Replace spill tray in lower part of bezel.

9

Align cube switch with sliding lever and firmly push until sliding lever is flush with bezel.

52

For a left hinge door, cut 5/8 x 7/8 in lower left corner. Note: Steps show panel upside down and notched for left hinge application. Mirror dimensions for right hinge door.

For a left hinge door, cut 5/8 x 3 in lower left corner. Note: Steps show panel upside down and notched for left hinge application. Mirror dimensions for right hinge door.

Measure and cut 2 1/16 diagonal in lower left corner.

Cut out diagonal in lower left corner.

7/8(2.2cm)

5/8(1.6 cm)

3

2 1

1a For Models made before 9/22/06

3(7.6 cm)

5/8(1.6 cm)

3

2 1

1b For Models made after 9/22/06

1-13/16 (4.60 cm)

2b For Models made after 9/22/06

3/32

(.24 cm)

5/8(1.6 cm)

3

3

2

1

Bottom Mount Custom Panel Hinge Cutout (if required)

Measure and cut 1/8 x 2 diagonal in lower left corner.

2(5.1 cm)

1/8

(0.3 cm) 2a For Models made before 9/22/06

Final view of lower corner.

4 1/4 (0.6 cm)

base panel added

Surfaces are flush

53

1 2

Remove air grille center blade. Remove two 1/4 (.6 cm) screws with a magnetic extended screwdriver at least 8 (20.3 cm) long.

3 4

Pull air grille assembly forward. Remove two mounting brackets from the grille air assembly.

5 6

Using eight screws removed from the mounting brackets, attach mounting brackets to the custom wood grille using predrilled pilot holes. (See grille overlay specifications for

proper alignment and pilot hole placement.)

Insert custom air grille assembly.

Custom Grille Installation

54

Install two 1/4 (.6 cm) screws with a magnetic extended screwdriver at least 8 (20.3 cm) long.

Install custom air grille center blade.

7 8

General Information

Area Requirements Verify the following: Unit can fit into residence and can be moved around corners and through doorways.

Floors can support units weight plus food weight (approximately 1200 pounds [540 kg] per unit).

Rear wall is solid and is able to support two horizontally mounted 2X4s (included) bolted to two wall studs. The 2X4 board bolt heads must be flush with 2X4 to prevent obstruction.

Remove anything attached to rear or side walls that can obstruct unit installation.

Cutout dimensions are accurate.

Electrical outlet is in correct location.

Water line is in correct location.

Do not install a refrigeration unit near a heat source, nor in a location where the surrounding temperature will fall below 60 F (16 C).

Electrical Requirements It is the customers responsibility to: contact a qualified electrical installer. assure that the electrical installation is adequate and in conformance with the National Electrical Code, ANSI/NFPA 70- latest edition or Canadian Electrical Code C22.1-1998 and C22.2 No. 0-M91 (or latest edition), and all local codes and

ordinances. A 115 volt, 60-Hz, 15 amp, fused, electrical supply is required. It is required that a separate circuit serving only this appliance be provided. This appliance is equipped with a power supply cord having a 3-prong grounding plug. To minimize possible shock hazard, the cord must be plugged into a mating 3-prong, grounding-type wall receptacle. Do not use an extension cord.

If codes permit a separate grounding wire to be used, it is recommended that a qualified electrician determine that the grounding path is adequate.

DO NOT ground to a gas line. Check with a qualified electrician if you are not sure if the appliance is properly grounded. DO NOT have a fuse in the neutral or grounding circuit.

Anti-Tip Requirements The anti-tip boards should be fastened into position prior to moving the unit into the opening.

Note: Additional mounting boards may be required if the unit does not touch the back wall of the enclosure. To prevent unit from tipping forward, it must be secured in place with a solid soffit or wood block.

55

General Information

Water Supply Requirements

Use only 1/4 (6 mm) copper tubing for water line. Do Not install copper tubing in area where temperatures drop below 35 F (1.7 C). Before attaching copper tubing to the unit, flush at least 2 quarts (1.9 L) of water through the copper tubing and into a bucket to remove any particles in the water line.

Viking Range Corporation is not responsible for property damage due to improper installation or water connection.

Connect 1/4 (6mm) flexible copper tubing to household plumbing in compliance with local codes and ordinances.

Length of copper tubing must reach from water supply connection to the unit connection with an additional length to facilitate moving the unit out of enclosure for cleaning or service. Tubing should be soft instead of rigid and ends should be free of burrs.

Copper tubing route must be above 35 F (1.7 C) to prevent water line from freezing.

Do not use plastic water lines from the household plumbing to the water inlet valve connection on the refrigeration unit.

Do not use the self-piercing feature of a saddle valve. The hole made by the piercing lance is too small for the water flow rate required by the ice maker.

If saddle valve is not used, place a separate shut-off valve in an easily accessible location between water supply and the unit. Do not install shut-off valve behind the unit.

The installation of Viking units with a reverse osmosis system is acceptable as long as the water pressure remains within the allowable PSI as stated below. It is important to note that with many reverse osmosis systems, the pressure starts off high, but then it decreases as the water level of the reverse osmosis storage area drops. This must be considered when checking the water pressure coming into the unit.

Connect a vertical or horizontal 1/2 (1.2 cm) to 1 1/4 (3.2 cm) COLD water line near water area.

Run water line through the floor, back, or side wall. Tubing should lay flat on floor underneath the unit. Clamp tubing to wall or floor.

Water pressure must be greater than 20 psi and less than 120 psi on non-dispensers and greater than 35 psi and less than 120 psi on dispensers.

56

To avoid serious illness or death, do not use unit where water is microbiologically unsafe or of unknown quality, without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected water that may contain filterable cysts. The contaminants or other substances removed or reduced by this water treatment system are not necessarily in your water.

W A R N I N G

General Information

57

Most of the units weight is at the top. Extra care is needed when moving the unit to prevent tipping.

Do Not remove protective film until unit is in operating position.

All four leveling legs must make contact with the floor to support and stabilize the full weight.

Do not drop unit.

Remove exterior shipping materials prior to moving unit into home.

Use two or more people to move and install unit. Failure to follow this instruction can result in back or other injury.

To avoid personal injury, wear gloves when performing any installation procedure and wear eye protection when cutting metal straps.

TIP OVER HAZARD Appliance is top heavy and tips easily when not completely installed. Keep doors closed until appliance is completely installed and secured per installation instructions. Use two or more people to move and install the appliance. Failure to do so can result in death or serious injury.

Unpacking unit 1. Remove top and bottom strap.

2. Remove top cap.

3. Cut rear of carton approximately 1/4 (0.6 cm) to 1 (2.5 cm) from right corner with a utility knife extended 1/4 (0.6 cm).

4. Remove carton and exterior packaging. Save cardboard shipping material to protect floor surface when installing unit. Remove anti-tip board, kickplate and door trim pieces (DF models) from rear of unit.

Moving Unit

Remove shipping brackets from skid by removing four bolts (two on each side) with a 1/2 deep-well socket

wench and a pair of pliers. Note: Tilting unit is not required to remove

shipping brackets.

Slip appliance dolly between unit and skid. Remove unit from skid.

Note: Use excess packaging to protect decorative trim; also, verify that leveling legs are up (0 adjustment).

58

1 2a

Place unit in front of cutout. (Professional) Lift center grille louver up and pull out.

2b 3

(Designer) Pull the center grille louver up at an angle and pull out.

Using an 8 magnetic nut driver, remove the two 1/4 screws.

4

Remove grille assembly.

Installation

59

Remove four side screws and remove unit top. Loosen the four hinge screws. Adjust door. Retighten four hinge screws.

Replace unit top. Replace four side screws. Attach one 2x4 to wall stud (refer to dimensions page for exact location).

If needed, depending on cabinet and depth, attach second 2x4 to first 2x4.

2

1

5 Front of unit

2

1 3

6

1

2

7 8a

Wall

2 x 4

Refrigerator

8b

Wall

2 x 4

Refrigerator

Hinge Adjustment

9

Plug in power cord to verify operation. Note: Make sure power switch and showroom switch

are in the On Position.

60

3

10a

Place unit within 3 of being flush with cabinets. Note: To avoid cabinet damage, place cardboard

between cabinets and unit. When moving unit, do not crimp, kink or crush water supply line.

10b

11

Carefully move unit until semi flush with cabinet (depending on unit).

Pull supply tubing forward under unit. Note: DO NOT use plastic water lines.

12

13

Flush water line by running two quarts of water into a bucket. Turn water off.

Connect supply tube to water valve using a 1/2 wrench. Note: DO NOT overtighten.

Turn on water supply and check for leaks.

14

61

Lift unit off rollers to desired height and level unit using a 5/16 head wrench.

Note: DO NOT use an electric device. Overtightening can cause damage.

Attach positive secure self-tapping bolts to 2x4 using a 22 extension.

Verify that drain pan is installed and aligned.

Align holes on both ends of louvered panels and insert screws.

Using a Phillips screwdriver, attach the kickplate to the unit and adjust to desired height.

15

Wall

2 x 4

Refrigerator

Screw

16

17

1

2

18

21

3

19

Kickplate Installation

62

3

1

2

20

Open refrigerator door so door stop and shoulder screw are accessible.

Note: Shoulder screw should be in 110 door opening position.

Remove shoulder screw and place in 90 or 120 position.

3

1 2

22

1

2

23

110

90

120

Open refrigerator door so door stop and shoulder screw are accessible.

Note: Shoulder screw should be in 110 door opening position.

Remove shoulder screw and place in 90 or 120 position.

Door Stop Adjustment (Side-by-Side)

Door Stop Adjustment (Bottom Mount)

1

2

21

110 120

90

63

Locate water filter door. The door is located under the Meat Savor/Produce drawer handle.

Push upper left corner of door to release latch and pull door downward.

Insert filter cartridge into circular opening in filter housing. Rotate clockwise gently until filter stops.

Close water filter door.

Note: Allow 1-2 minute delay in water dispersal to allow internal water tank to fill.

Flush air from the system by running water through the dispenser continuously for 3 minutes.

24

2

1

25

1 3

2

26 27

Water Filter Installation (Side-by-Side with Dispenser)

64

Water Filter System Specification and Performance Data Sheet This system has been tested according to NSF/ANSI 42/53 for reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration of less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI 42/53.* (100% safety factors built- in for unmetered usage for health claims only.)

*Tested using a flow rate of 0.5 gpm; pressure of 60 psig; pH of 7.5 + 0.5; temp of 68o + 5oF (20o + 3oC) **Measurement in particles/mL. Particles used were 0.5 - 1 microns ***NTU = Nephelometric Turbidity units

Operating Specifications Capacity: Certified for up to 750 gallons (2,838 L); up to nine months Pressure Requirement: 20 - 120 psi (2.8 - 8.2 bar) Temperature: 33-100oF (0.6 - 38oC) Flow rate: 0.78 gpm (2.9 l/min.)

Check for compliance with the state and local laws and regulations. Note: While the testing was performed under standard laboratory conditions, actual performance may vary. Must be installed and operated in accordance with manufacturers recommended procedures and guidelines. Installation instructions, parts and service availability, and standard warranty are included with the product when shipped. This drinking water system must be maintained according to manufacturers instruction, including replacement of filter cartridges.

Standard No. 42: Aesthetic Effects Parameter USEPA Influent Influent Effluent %Reduction Min. Req.

McL Average Challenge Average Maximum Average Minimum Reduction Concentrations

Chlorine 1.88 mg/L 2.0 mg/L + 10% <0.05mg/L 0.06 mg/L >97.26% 96.84% > 50% T&O Particulates** 5,700,000 #/mL at least 29.83#/mL 140 #/mL 99.98% 99.91% > 85%

10,000 particles/mL

Standard No. 53: Health Effects Parameter USEPA Influent Influent Effluent %Reduction Min. Req.

McL Average Challenge Average Maximum Average Minimum Reduction Concentrations

Turbidity 1 NTU*** 10.73 NTU*** 11 + 1 NTU 0.36 NTU .049 NTU 97.09% 95.20% 0.5 NTU Cysts 99.95% Reduction 200,000 #/L min. 50,000/L <1 <1 >99.99% >99.99% >99.95%

Asbestos 99% Reduction 155 MF/L 107 & 108 fibers/L <1 <1 >99.99% >99.99% 99%

fibers>10micrometers

Lead at pH 6.5 0.015 mg/L 0.153 mg/L 0.15mg/L + 10% <.001 <.001 >99.35% >99.35% 0.010 mg/L Lead at pH 8.5 0.015 mg/L 0.150 mg/L 0.15mg/L + 10% <.001 <.001 >99.35% 97.35% 0.010 mg/L Mercury at pH 6.5 0.002 mg/L 0.006 mg/L .006mg/L + -10% 0.00026 0.0005 98.72% 90.91% 0.002mg/L Mercury at pH 8.5 0.002mg/L 0.006 mg/L .006mg/L + -10% 0.0008 0.0015 98.72% 75.93% 0.002mg/L Lindane 0.0002 mg/L 0.002 mg/L .002mg/L + 10% 0.000025 0.00007 98.72% 96.50% 0.0002mg/L Atrazine 0.003 mg/L 0.00873 mg/L .009mg/L + 10% <.002 mg/L <.002 mg/L 76.99% 75.31% 0.003 mg/L Toxaphene 0.003 mg/L 0.015 mg/L .015mg/L + 10% <0.001 <0.001 92.97% 91.67% 0.003mg/L

Manufactured by: Cuno, a 3M company 1000 Apollo Road Eagan, MN 55121 (651) 450-4913

System tested and certified by NSF International against Standard 42 for the reduction of chlorine taste and odor, particulate Class I and Standard 53 for the reduction of Lead, Lindane, Atrazine, Mercury, Toxaphene, Cyst, Turbidity, and Asbestos.

65

Replace top air grille. Using an 8 magnetic nut driver, replace the two 1/4 screws.

(Professional) Replace the center grille louver. (Designer) Replace the center grille louver.

Open door. The display should flash. Press DISPLAY ON or ACTIVATE CONTROLS pad and close door.

Note: There is a 6 minute delay before the unit starts.

28 29

30a 30b

31 32

Final Installation

66

Performance Checklist

h Verify cabinet size.

h Verify electrical supply and water supply (if applicable).

h Install anti-tip device(s) and verify unit is secure.

h Position unit in cutout, level at desired height and secure unit.

h Plug-in unit and verify operation.

h Connect water supply (if applicable). Verify icemaker fill tube is properly inserted.

Verify icemaker bail arm is down. Verify dispenser operation (if applicable).

h Align/square door(s).

h Verify drain pan is properly installed and there are no leaks on water connection.

h Install kickplate.

h Remove internal packaging and labels and wipe unit down.

Installers information:

Installers Name:_____________________________

Installers Company:_________________________

Date: _________________________________________

67

Control Panels

1. Press Display On or Activate Controls pad 2. Verify unit is not in Sabbath Mode If in Sabbath Mode: A. The Sabbath Mode will disable the interior lights, display (except 3 blue squares) and alarm. (See

picture below for visual indication of Sabbath Mode)

To exit the Sabbath Mode: B. Press & Hold Display On or Activate Controls and then Display Off for 3 seconds. (The

control will beep 3 times to alert the user the Sabbath Mode has been exited) 3. Verify unit is not in Showroom Mode If in Showroom Mode: A. The Showroom Mode will disable the refrigerator system but all other functions are normal. These

include lights and control. (See picture below for visual indication of Showroom Mode)

To exit Showroom Mode: B. Press & Hold Display On or Activate Controls; while holding, press and hold Higher Temp

and Alarm Off together. (The control will beep 3 times to alert the user that Showroom Mode has been exited)

4. Press Max Frz & Display Off at the same time and hold until beeps (force start compressor). 5. All models need to be set at the 5th bar for Refrigerator & Freezer - factory setting.

Verify Operations

DISPLAY ON

FRZ TEMP

REF TEMP

HIGHER TEMP

LOWER TEMP

HIDDEN BUTTON

MAX REF

MAX FRZ

ALARM OFF

DISPLAY OFF

FRZ TEMP

FRZ TEMP

HIGH TEMP

MAX REF

MAX FRZ

COLDEST. . . . . . . . . . .

DOOR OPEN

Bottom Mount

FRZ TEMP

FRZ TEMP

HIGH TEMP

MAX REF

MAX FRZ

COLDEST. . . . . . . . . . .

DOOR OPEN

DISPLAY ON

FRZ TEMP

REF TEMP

HIGHER TEMP

LOWER TEMP

HIDDEN BUTTON

MAX REF

MAX FRZ

ALARM OFF

DISPLAY OFF

FRZ TEMP

FRZ TEMP

HIGH TEMP

MAX REF

MAX FRZ

COLDEST. . . . . . . . . . .

DOOR OPEN

D

Side by Side

FRZ TEMP

FRZ TEMP

HIGH TEMP

MAX REF

MAX FRZ

COLDEST. . . . . . . . . . .

DOOR OPEN

68

Verify Operations

Control Panels

1. Press Display On or Activate Controls pad 2. Verify unit is not in Sabbath Mode If in Sabbath Mode: A. The Sabbath Mode will disable the interior lights, display (except 3 blue squares) and alarm. (See

picture below for visual indication of Sabbath Mode)

To exit the Sabbath Mode: B. Press & Hold Display On or Activate Controls and then Display Off for 3 seconds. (The

control will beep 3 times to alert the user the Sabbath Mode has been exited) 3. Verify unit is not in Showroom Mode If in Showroom Mode: A. The Showroom Mode will disable the refrigerator system but all other functions are normal. These

include lights and control. (See picture below for visual indication of Showroom Mode)

To exit Showroom Mode: B. Press & Hold Display On or Activate Controls; while holding, press and hold Higher Temp

and Alarm Off together. (The control will beep 3 times to alert the user that Showroom Mode has been exited)

4. Press Max Frz & Display Off at the same time and hold until beeps (force start compressor). 5. All models need to be set at the 5th bar for Refrigerator & Freezer - factory setting.

ACTIVATE CONTROLS

REF TEMP

HIGHER TEMP

LOWER TEMP

HIDDEN BUTTON

HIDDEN BUTTON MAX FRZ

MAX REF

ALARM OFF

DISPLAY OFF

FRZ TEMP

HIGH TEMP

MAX REF

COLDEST. . . . . . . . . . . . . .

DOOR OPEN

All Refrigerator

FRZ TEMP

FRZ TEMP

HIGH TEMP

MAX REF

MAX FRZ

COLDEST. . . . . . . . . . .

DOOR OPEN

ACTIVATE CONTROLS

FRZ TEMP

HIGHER TEMP

LOWER TEMP

HIDDEN BUTTON

HIDDEN BUTTON MAX REF

MAX FRZ

ALARM OFF

DISPLAY OFF

FRZ TEMP

HIGH TEMP

MAX REF

COLDEST. . . . . . . . . . . . . .

DOOR OPEN

All Freezer

FRZ TEMP

FRZ TEMP

HIGH TEMP

MAX REF

MAX FRZ

COLDEST. . . . . . . . . . .

DOOR OPEN

F

69

Service & Parts Only authorized replacement parts may be used in performing service on the appliance. Do not repair or replace any part of the appliance unless specifically recommended in the manual. All other servicing should be referred to a qualified technician.

Record the following information indicated below. You will need it if service is ever required. The serial number and model number for your appliance are located on the identification plate mounted behind the top light.

Model Number

_________________________________________

Serial Number

_________________________________________

Date of Purchase

_________________________