Contents

Viking DFFB536 Refrigerator Installation Guide PDF

1 of 38
1 of 38

Summary of Content for Viking DFFB536 Refrigerator Installation Guide PDF

Viking Range Corporation

111 Front Street

Greenwood, Mississippi 38930 USA

(662) 455-1200

For product information,

call 1-888-VIKING1 (845-4641)

or visit the Viking Web site at

vikingrange.com

F20634D EN (121211)

Viking Installation Guide

Custom Panel Models All Refrigerator/Freezer/

Side-by-Side/Bottom-MountULCUL

32

Table of Contents Warnings & Important Information ____________________________________________________________________3 Bottom-Mount

Dimensions and Specifications (36) __________________________________________________________6 Cutout Dimensions (36) ____________________________________________________________________8 Anti-Tip Dimensions (36) ___________________________________________________________________9 Overlay Dimensions (36) __________________________________________________________________10 Custom Grille Dimensions (36)_____________________________________________________________11

Side-By-Side Dimensions (42) _________________________________________________________________________13 Dimensions (48) ________________________________________________________________________14 Specifications (42 and 48) ________________________________________________________________15 Cutout Dimensions (42) __________________________________________________________________16 Anti-Tip Dimensions (42) _________________________________________________________________17 Cutout Dimensions (48) ___________________________________________________________________18 Anti-Tip Dimensions (48) __________________________________________________________________19 Overlay Dimensions (42) __________________________________________________________________20 Overlay Dimensions (48) __________________________________________________________________21 Custom Grille Dimensions (42) ____________________________________________________________22 Custom Grille Dimensions (48) ____________________________________________________________23

All Refrigerator/Freezer Dimensions & Specifications (30 and 36) ___________________________________________________24 Cutout Dimensions (30) ___________________________________________________________________26 Anti-Tip Dimensions (30) __________________________________________________________________27 Cutout Dimensions (36) ___________________________________________________________________28 Anti-Tip Dimensions (36) __________________________________________________________________29 Dimensions (Dual 30) _____________________________________________________________________30 Dimensions (Dual 30 and 36) _____________________________________________________________31 Dimensions (Dual 36) _____________________________________________________________________32 Specifications (Dual) _______________________________________________________________________33 Cutout Dimensions (Dual 30) ______________________________________________________________34 Anti-Tip Dimensions (Dual 30) _____________________________________________________________35 Cutout Dimensions (Dual 30 and 36) ______________________________________________________36 Anti-Tip Dimensions (Dual 30 and 36) _____________________________________________________37 Cutout Dimensions (Dual 36) ______________________________________________________________38 Anti-Tip Dimensions (Dual 36) _____________________________________________________________39 Overlay Dimensions (30 & 36) ____________________________________________________________40 Custom Grille Dimensions (30)_____________________________________________________________41 Custom Grille Dimensions (36)_____________________________________________________________42 Custom Grille Dimensions (Dual 30) ________________________________________________________43 Custom Grille Dimensions (Dual 30 and 36) ________________________________________________44 Custom Grille Dimensions (Dual 36) ________________________________________________________45

Cabinet Information _______________________________________________________________________________46 Custom Side Panel Dimensions _____________________________________________________________________48 Custom Panel General Information __________________________________________________________________49 Ice and Water Dispenser Bezel Removal______________________________________________________________49 Custom Door Panel Installation (Refrigerator or Freezer) ______________________________________________51 Ice and Water Dispenser Bezel Installation____________________________________________________________54 Door Trim Insert ___________________________________________________________________________________55 Custom Panel Hinge Cutout ________________________________________________________________________56 Custom Grille Installation ___________________________________________________________________________56 General Information _______________________________________________________________________________58

Unpacking & Moving ______________________________________________________________________60 Installation________________________________________________________________________________________61

Hinge Adjustment_________________________________________________________________________62 Kickplate Installation_______________________________________________________________________64 Door Stop Adjustment_____________________________________________________________________65 Water Filter Installation ____________________________________________________________________66 Water Filter System Specifications___________________________________________________________67 Final Installation __________________________________________________________________________68

Performance Checklist _____________________________________________________________________________69 Control Panels ____________________________________________________________________________________70 Service & Registration______________________________________________________________________________72

IMPORTANT Please Read and Follow Make sure that incoming voltage is the same as unit rating. An electric rating plate specifying voltage, frequency, wattage, amperage, and phase is attached to the product.

To reduce the risk of fire, electrical shock, or injury to persons, installation work and electrical wiring must be done by a qualified technician in accordance with all applicable codes and standards, including fire-rated construction.

The installer should leave these instructions with the consumer who should retain them for local inspectors use and for future reference.

It is your responsibility to: Comply with installation specifications and dimensions.

Properly install unit. Remove any moldings or decorative panels that prevent the unit from being serviced.

Make sure that you have these materials (not provided with your unit), which are necessary for proper installation: 1/4 (6 mm) copper tubing with shutoff valve 6 #8 x 3 (7.6 cm) wood screws (longer screws may be required)

1 Saddle valve (DO NOT use self-piercing feature of the valve)

Assure that floor will support unit, door panels and contents (approximately 1200 pounds [540 kg]).

Provide a properly grounded electrical outlet. Assure that location will permit appliance doors to open a minimum of 90.

Your safety and the safety of others is very important.

We have provided many important safety messages in this manual and on your appliance. ALWAYS read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to hazards that can kill or hurt you and others.

All safety messages will be preceded by the safety alert symbol and the word DANGER or WARNING. These words mean:

Hazards or unsafe practices whichWILL result in severe personal

injury or death

DANGER

Hazards or unsafe practices which COULD result in severe personal

injury or death

All safety messages will identify the hazard, tell you how to reduce the chance of injury, and tell you what can happen if

the instructions are not followed.

WARNING

5

IMPORTANTPlease Read and Follow!

4

A GFI shall be used if required by NFPA-70 (National Electric Code), federal/state/local laws, or local ordinances. The required use of a GFI is normally related to the location of a receptacle with respect to

any significant sources of water or moisture. Viking Range Corporation will NOT warranty any problems resulting from GFI outlets which

are not installed properly or do not meet the requirements below.

If the use of a GFI is required, it should be: Of the receptacle type (breaker type or portable type NOT recommended) Used with permanent wiring only (temporary or portable wiring NOT recommended) On a dedicated circuit (no other receptacles, switches or loads in the circuit) Connected to a standard breaker of appropriate size (GFI breaker of the same size NOT

recommended) Rated for Class A (5 mA +/- 1 mA trip current) as per UL 943 standard) In good condition and free from any loose-fitting gaskets (if applicable in outdoor situations) Protected from moisture (water, steam, high humidity) as much as reasonably possible

ELECTRICAL SHOCK HAZARD Disconnect power or turn power disconnect switch to

OFF position before removing top grille. Failure to do so can result in death or electric shock.

WARNINGWARNING TIP OVER HAZARD Appliance is top heavy and tips easily when not completely installed. Keep doors closed until appliance

is completely installed and secured per installation instructions.

Use two or more people to move and install appliance. Failure to do so can result in death or serious injury.

Most of the units weight is at the top. Extra care is needed when moving the unit to prevent tipping. Use cardboard shipping material or plywood under unit until it is installed in the operating position to protect floor surface.

Specifications (Bottom-Mount)

51-7/8(131.8 cm)

23-1/16(58.6 cm)

3-1/2(8.9 cm)

82-7/8(210.5 cm)min. to84-1/16(213.5 cm)max.

Measurement varies

(locally supplied hardware)

23-13/16

(60.5 cm)

24-3/4

(62.9 cm)

35(88.9 cm)

36(91.4 cm)

Dimensions (Bottom-Mount)

76

36 Bottom-Mount Description DFBB536 Overall width 36 (91.5 cm) Overall height (from bottom) 82-3/4 (210.2 cm) min. to 84-1/16 (213.5 cm) max. Overall depth (from rear) To front edge of side trim: 23-13/16 (60.5 cm)

To front of top grille: 24-3/4 (62.9 cm) To front edge of door trim: 24 (61.0 cm)

Cutout width 36 (91.5 cm) Cutout height 82-7/8 (210.5 cm) min. to 84-1/16 (213.5 cm) max. Cutout depth 24 (61.0 cm) min.* Electrical requirements 115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with

grounded 3-prong plug attached to product Maximum amp usage 9.9 amps Inlet water requirements 1/4 copper tubing inlet waterline; minimum 20 psi;

maximum 120 psi Overall interior dimensions

Refrigerator 15.2 cu. ft. (431 liters) Freezer 5.1 cu. ft. (145 liters) Total capacity 20.3 cu. ft. (576 liters)

Maximum panel weight Fresh food 45 lbs. (20.4 kg) Freezer 20 lbs. (9.0 kg) Approximate shipping weight 500 lbs. (227.3 kg)

*Note: Custom panel models fit flush in 25 (63.5 cm) deep cabinet openings. They can be installed in standard 24 (61.0 cm) deep openings. The door faces and top grille will protrude 3/4 (1.9 cm) into the room.

36 Bottom-Mount

98

9(22.9 cm)

73-3/8(186.4 cm)

82-7/8(210.5 cm) min. anti-tip board &opening height

84-1/16(213.5 cm) max. anti-tip board & opening height

36(91.5 cm)

24 (61.0 cm) Electric Outlet Location

Water Line Entry Area

36(91.5 cm) 6-3/4(17.1 cm)

7-5/8(19.4 cm)

3(7.6 cm)

5/8(1.5 cm)

5/8(1.5 cm)

10-1/2(26.7 cm) 5/8(1.5 cm)

10-3/4(27.3 cm)

1 (2.5 cm)

3-5/8(9.2 cm)

Optional floor

water line entry

See anti-tip board installation 6 (15.2 cm)

9 (22.9 cm)

Cutout Dimensions (Bottom-Mount)

36 Bottom-Mount

One 2x 4 mounting board 1-1/2 (3.8 cm) x 3-1/2 (8.9 cm) Note: If unit is installed deeper than 24 (61.0 cm), then shim behind the mounting board by the difference.

Note: Top of unit must be placed firmly under anti-tip board. Bottom of anti-tip board is 3-7/8 (9.8 cm) below opening height.

Anti-Tip Location

79-3/8(201.6 cm) min.to bottom ofanti-tip board

80-1/2(204.6 cm) max.to bottom ofanti-tip board

29 (73.7 cm)

3-1/2(8.9 cm)

1-1/2

(3.8 cm)

Anti-Tip Dimensions (Bottom-Mount)

36 Bottom-Mount

One 2x4 mounting board 1-1/2 (3.8 cm) x 3-1/2 (8.9 cm) Note: If unit is installed deeper than 24 (61.0 cm), then shim behind the mounting board by the difference.

Bottom f anti-tip board is 3-7/8 (9. cm) below the opening height. Note: Top of unit mus be placed firmly under anti- p board.

Reverse dimensions for other end.

1/2(1.27 cm)

1-1/2

(3.81 cm)

1/4 Radius

(.64 cm)

2-3/4

(6.98 cm)

1/2(1.27 cm)

3/4(1.90 cm)

1/2

(1.27 cm)

1/8(.31 cm)

1/2(1.27 cm)

1/4 Radius

(1.2 cm)

.64

7/8

(2.22 cm)

1/2 (1.27 cm)34(86.36 cm)

34(86.36 cm)

3/4(1.90 cm)

1/2(1.27 cm)

3/4(1.90 cm)

3-3/4

(9.52 cm)

3-3/4

(9.52 cm)

3-5/8

(9.20 cm)

33-15/16 (86.20 cm)

3

(7.62 cm)

3

(7.62 cm)

3/4(1.90 cm)

35-1/2(90.17 cm)

1/2(1.27 cm)

3-1/8

(7.93 cm)

Optional hinge cover

32-3/16(81.75 cm)

5-17/32(14.10 cm)

4-11/64(10.59 cm)

30-27/32 (78.34 cm)

3-25/32 (9.60 cm)

27/32 (.84 cm)

9/16

(1.42 cm)

1/4

(.635 cm)

16.5 20.0

2-1/8(5.4 cm)

Custom Grille Dimensions (Bottom-Mount)

35-1/4(89.5 cm)

23-1/16(58.6 cm)

3/4

(1.9 cm)

35-1/4(89.5 cm)

32-1/4 to notch (81.9 cm)

5/8(1.6 cm) 51-7/8(131.8 cm)

51-1/4(130.2 cm)

3/4

(1.9 cm)

Note: Corner notch is for left

hinge door. Reverse for right hinge.

See page 54 for cutout instructions.

1-13/16 (4.60 cm)

5/8 (1.6 cm)

3(7.62 cm)

3/32

(.24 cm)

Note: Inset shown upside down.

Overlay Dimensions (Bottom-Mount)

1110

36 Custom Panels 36 Custom Grille

Note: Panel overlays must be dry, solid, straight one-piece panels. The use of multiple panel pieces to achieve the dimensions is not recommended.

Dimensions (Side-By-Side)

3 25/32 (9.60 cm)

27/32 (.84 cm)

9/16

(1.42 cm)

1/4

(.635 cm)

16.5 20.0

Note: This part should be located at the center of the grille. If desired, two per grille can be used by dividing the length of the grille into thirds.

1/2(1.27 cm)

1-1/2

(3.81 cm)

1/4 Radius

(.64 cm)

2-3/4

(6.98 cm)

1/2(1.27 cm)

3/4(1.90 cm)

3/8 (0.38 cm)

1/2 (1.27 cm)

R 3/32 (0.09 cm)

3/4 (1.90 cm)

3/4 (1.90 cm)

3/4 (1.90 cm)

13/32 (1.03 cm)

9/16 (1.43 cm)

1/8 (.32 cm)

Grille support

2-7/8(7.30 cm)

1(2.54 cm)

1/2

(1.27 cm)

1/8(.31 cm)

1/2(1.27 cm)

1/4 Radius

(1.2 cm)

.64

Reverse dimensions for other end.

7/8

(2.22 cm)

1/2 (1.27 cm)

1/2(1.27 cm) 3-1/8

(7.93 cm)

Optional hinge cover

1/2(1.27 cm)

3-5/8

(9.20 cm)

3/4(1.90 cm)

3/4(1.90 cm)

3-3/4

(9.52 cm)

3-3/4

(9.52 cm)

3

(7.62 cm)

3

(7.62 cm)

3/4(1.90 cm)

71-1/2(181.61 cm)

70(177.80 cm

69-15/16 (177.64 cm)

70(177.80 cm)

68-3/64 (172.83 cm)

66-27/32 (169.78 cm)

4-11/64(11.27 cm)

5-17/32(14.04 cm) 30-27/32 (78.34 cm)

32-3/16(81.75 cm)

40-11/64 (102.03 cm)

41-25/64 (10 5.13 cm)

Custom Grille Dimensions (Bottom-Mount)

1312

Dual 36 Custom Grille 42 Side-By-Side

75-15/16 (192.9 cm)

3-1/2(8.9 cm)

82-7/8(210.5 cm)min. to84-1/16(213.5 cm)max.

Measurement varies

(locally supplied hardware)

23-13/16

(60.5 cm)

24-3/4

(62.9 cm)

41(104.1 cm)

42(106.7 cm)

Specifications (Side-By-Side)

75-15/16 (192.9 cm)

3-1/2(8.9 cm)

82-7/8(210.5 cm)min. to84-1/16(213.5 cm)max.

23-13/16

(60.5 cm)

24-3/4

(62.9 cm)

47(119.4 cm)

48(121.9 cm)

Measurement varies

(locally supplied hardware)

Dimensions (Side-By-Side)

1514

42 Side-By-Side Description DFSB542 DFSB542D Overall width 42 (106.7 cm) Overall height (from bottom) 82-3/4 (210.2 cm) min. to 84-1/16 (213.5 cm) max. Overall depth (from rear) To front edge of side trim: 23-13/16 (60.5 cm)

To front of top grille: 24-3/4 (62.9 cm) To front edge of door trim: 24 (61.0 cm)*

Cutout width 42 (106.7 cm) Cutout height 82-7/8 (210.5 cm) min. to 84-1/16 (213.5 cm) max. Cutout depth 24 (61.0 cm) min.* Electrical requirements 115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with

grounded 3-prong plug attached to product Maximum amp usage 9.9 amps Inlet water requirements 1/4 copper tubing inlet waterline; 1/4 copper tubing inlet waterline;

minimum 20 psi; maximum 120 psi minimum 35 psi; maximum 120 psi Overall interior dimensions Refrigerator 15.0 cu. ft. (425 liters) 14.5 cu. ft. (411 liters) Freezer 9.0 cu. ft. (255 liters) 8.6 cu. ft. (244 liters) Total capacity 24.0 cu. ft. (680 liters) 23.1 cu. ft. (654 liters)

Maximum panel weight Fresh food 40 lbs. (18.1 kg) Freezer 35 lbs. (15.9 kg) Approximate shipping weight 525 lbs. (236.2 kg)

48 Side-By-Side Description DFSB548 DFSB548D Overall width 48 (121.9 cm) Overall height (from bottom) 82-3/4 (210.2 cm) min. to 84-1/16 (213.5 cm) max. Overall depth (from rear) To front edge of side trim: 23-13/16 (60.5 cm)

To front of top grille: 24-3/4 (62.9 cm) To front edge of door trim: 24 (61.0 cm)*

Cutout width 48 (121.9 cm) Cutout height 82-7/8 (210.5 cm) min. to. 84-1/16 (213.5 cm) max Cutout depth 24 (61.0 cm) min.* Electrical requirements 115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with

grounded 3-prong plug attached to product Maximum amp usage 9.9 amps Inlet water requirements 1/4 copper tubing inlet waterline; 1/4 copper tubing inlet waterline;

minimum 20 psi; maximum 120 psi minimum 35 psi; maximum 120 psi Overall interior dimensions Refrigerator 18.5 cu. ft. (524 liters) 17.9 cu. ft. (507 liters) Freezer 8.9 cu. ft. (252 liters) 8.5 cu. ft. (241 liters) Total capacity 27.4 cu. ft. (776 liters) 26.4 cu. ft. (748 liters)

Maximum panel weight Fresh food 50 lbs. (22.7 kg) Freezer 35 lbs. (15.9 kg) Approximate shipping weight 650 lbs. (292.5 kg)

*Note: Custom panel models fit flush in 25 (63.5 cm) deep cabinet openings. They can be installed in standard 24 (61.0 cm) deep openings. The door faces and top grille will protrude 3/4 (1.9 cm) into the room.

48 Side-By-Side

1716

One 2x 4 mounting board 1-1/2 (3.8 cm) x 3-1/2 (8.9 cm)

Note: If unit is installed deeper than 24 (61.0 cm), then shim behind the mounting board by the difference.

Bottom of anti-tip board is 3-7/8 (9.8 cm) below opening height. Note: Top of unit must be placed firmly under anti-tip board.

Anti-Tip Location

79-3/8(201.6 cm) min.to bottom ofanti-tip board

80-1/2(204.6 cm) max.to bottom ofanti-tip board

35 (88.9 cm)

3-1/2(8.9 cm)

1-1/2

(3.8 cm)

Anti-Tip Dimensions (Side-By-Side)

9(22.9 cm)

73-3/8(186.4 cm)

82-7/8(210.5 cm) min. anti-tip board &opening height

84-1/16(213.5 cm) max. anti-tip board & opening height

42(106.7 cm)

24 (61.0 cm)

Electric Outlet Location

Water Line Entry Area

42(106.7 cm) 6-3/4(17.1 cm)

7-5/8(19.4 cm)

3(7.6 cm)

5/8(1.5 cm)

5/8(1.5 cm)

10-1/2(26.7 cm) 5/8(1.5 cm)

10-3/4(27.3 cm)

1 (2.5 cm)

3-5/8(9.2 cm)

Optional floor water line entry

See anti-tip board installation 6

(15.2 cm)

9 (22.9 cm)

Cutout Dimensions (Side-By-Side)

42 Side-By-Side 42 Side-By-Side

One 2x4 mounting board 1-1/2 (3.8 cm) x 3-1/2 (8.9 cm) Note: If unit is installed deeper than 24 (61.0 cm), then shim behind the mounting board by the difference.

Bottom of anti-tip board is 3-7/8 (9.8 cm) below the opening height. Note: Top of unit m st be plac d firmly under anti-tip board.

1918

One 2x 4 mounting boards 1-1/2 (3.8 cm) x 3-1/2 (8.9 cm)

Note: If unit is installed deeper than 24 (61.0 cm), then shim behind the mounting board by the difference.

Bottom of anti-tip board is 3-7/8 (9.8 cm) below opening height. Note: Top of unit must be placed firmly under anti-tip board.

Anti-Tip Location

79-3/8(201.6 cm) min.to bottom ofanti-tip board

80-1/2(204.6 cm) max.to bottom ofanti-tip board

41(104.1 cm)

3-1/2(8.9 cm)

1-1/2

(3.8 cm)

Anti-Tip Dimensions (Side-By-Side)

9(22.9 cm)

73-3/8(186.4 cm)

827/8(210.5 cm) min. anti-tip board &opening height

841/16(213.5 cm) max. anti-tip board & opening height

48(121.9 cm)

24 (61.0 cm)

Electric Outlet Location

Water Line Entry Area

47-1/2(120.7 cm) 6-3/4(17.1 cm)

7-5/8(19.4 cm)

3(7.6 cm)

5/8(1.5 cm)

5/8(1.5 cm)

10-1/2(26.7 cm) 5/8(1.5 cm)

10-3/4(27.3 cm)

1 (2.5 cm)

3-5/8(9.2 cm)

Optional floor water line entry

See anti-tip board installation 6

(15.2 cm)

9 (22.9 cm)

Cutout Dimensions (Side-By-Side)

48 Side-By-Side 48 Side-By-Side

One 2x4 mounting board 1-1/2 (3.8 cm) x 3-1/2 (8.9 cm) Note: If unit is i stalled deeper than 24 (61.0 cm), then shim behind the mounting board by the difference.

Bottom f anti-tip board is 3-7/8 (9.8 cm) below the ope ing height. Note: Top of unit must be placed firmly under anti-tip board.

28-5/16(71.9 cm)

75-1/2(191.8 cm)

3/4

(1.9 cm)

18-11/16 (47.5 cm)

3/4

(1.9 cm)

28-5/16(71.9 cm)

75-1/2(191.8 cm)

3/4

(1.9 cm)

18-11/16 (47.5 cm)

31-5/8(80.3 cm) 10-11/16 (27.1 cm)

12-3/8(31.4 cm)

3/4

(1.9 cm)

3-5/32(8.0 cm)

Overlay Dimensions (Side-By-Side)

22-13/16 (57.9 cm)

75-1/2(191.8 cm)

3/4

(1.9 cm)

3/4

(1.9 cm) 18-3/16(46.2 cm)

22-13/16 (57.9 cm)

75-1/2(191.8 cm)

3/4

(1.9 cm)

18-3/16(46.2 cm)

31-5/8(80.3 cm) 10-11/16 (27.1 cm)

12-3/8(31.4 cm)

3/4

(1.9 cm)

3-5/32(8.0 cm)

Overlay Dimensions (Side-By-Side)

2120

42 Custom Panels

42 Custom Panels with Dispenser

48 Custom Panels

48 Custom Panels with Dispenser

Note: Panel overlays must be dry, solid, straight one piece panels. The use of multiple panel pieces to achieve the dimensions is not recommended.

Note: Panel overlays must be dry, solid, straight one piece panels. The use of multiple panel pieces to achieve the dimensions is not recommended.

1/2

(1.27 cm)

1/8(.31 cm)

1/2(1.27 cm)

1/4 Radius

(1.2 cm)

.64

Reverse dimensions for other end.

7/8

(2.22 cm)

1/2 (1.27 cm)

2-1/8

(5.39 cm)

3-1/8

(7.94 cm)3-5/8 (9.20 cm)

1-3/8 (3.49 cm)

3/8

(.95 cm)

3/8 Radius (.95 cm)

47-1/2(120.65 cm)

1/2(1.27 cm)

3-1/8

(7.93 cm)

Optional hinge cover

46(116.84 cm)

1/2(1.27 cm)

3-5/8

(9.20 cm)

45-15/16 (116.68 cm)

46(116.84 cm)

3/4(1.90 cm)

3/4(1.90 cm)

3-3/4

(9.52 cm)

3-3/4

(9.52 cm)

3

(7.62 cm)

3

(7.62 cm)

3/4(1.90 cm)

30-27/32 (78.34 cm)

32-3/16(81.75 cm)

11-17/32 (29.28 cm)

10-11/64 (15.84 cm)

1/2(1.27 cm)

1-1/2

(3.81 cm)

1/4 Radius

(.64 cm)

2-3/4

(6.98 cm)

1/2(1.27 cm)

3/4(1.90 cm)

Custom Grille Dimensions (Side-By-Side)

1/2(1.27 cm)

1-1/2

(3.81 cm)

1/4 Radius

(.64 cm)

2-3/4

(6.98 cm)

1/2(1.27 cm)

3/4(1.90 cm)

1/2

(1.27 cm)

1/8(.31 cm)

1/2(1.27 cm)

1/4 Radius

(1.2 cm)

.64

Reverse dimensions for other end.

7/8

(2.22 cm)

1/2 (1.27 cm)

2-1/8

(5.39 cm)

3-1/8

(7.94 cm)3-5/8 (9.20 cm)

1-3/8 (3.49 cm)

3/8

(.95 cm)

3/8 Radius (.95 cm)

41-1/2(105.41 cm)

1/2(1.27 cm)

3-1/8

(7.93 cm)

Optional hinge cover

40(101.60 cm)

40(101.60 cm)

3/4(1.90 cm)

3/4(1.90 cm)

3-1/4

(9.52 cm)

3-3/4

(9.52 cm)

1/2(1.27 cm)

3-5/8

(9.20 cm)

39-15/16 (101.44 cm)

3

(7.62 cm)

3

(7.62 cm)

3/4(1.90 cm)

24-27/32 (63.10 cm)

26-3/16(66.51 cm)

5-17/32(14.04 cm)

4-11/64(10.60 cm)

Custom Grille Dimensions (Side-By-Side)

2322

42 Custom Grille 48 Custom Grille

35(88.9 cm)

23-13/16

(60.4 cm)

24-3/4

(62.9 cm)

82-7/8(210.5 cm)min. to84-15/16

(213.5 cm)max.

82-7/8(210.5 cm)min. to84-1/16(213.5 cm)max. 75-15/16

(192.9 cm)

3-1/2(8.9 cm)

75-15/16 (192.9 cm)

3-1/2(8.9 cm)

36(91.5 cm)

Measurement varies

(locally supplied hardware)

Measurement varies

(locally supplied hardware)

30(76.2 cm)

29(73.7 cm)

23-13/16

(60.4 cm)

24-3/4

(62.9 cm)

Dimensions (All Refrigerator/Freezer)

24 25

Specifications (All Refrigerator/Freezer)

30 All Refrigerator/Freezer Description DFFB530 DFRB530 Overall width 30 (76.2 cm) Overall height (from bottom) 82-3/4 (210.2 cm) min. to 84-1/16 (213.5 cm) max. Overall depth (from rear) To front edge of side trim: 23-13/16 (60.5 cm)

To front of top grille: 24-3/4 (62.9 cm) To front edge of door trim: 24 (61.0 cm)

Cutout width 30 (76.2 cm) Cutout height 82-7/8 (210.5 cm) min. to 84-1/16 (213.5 cm) max. Cutout depth 24 (61.0 cm) min.* Electrical requirements 115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with

grounded 3-prong plug attached to product Maximum amp usage 9.9 amps Inlet water requirements 1/4 copper tubing inlet

waterline; minimum 20 psi; N/A maximum 120 psi

Overall interior dimensions total capacity 15.9 cu. ft. (450 liters) 18.2 cu. ft. (516 liters) Maximum panel weight 50 lbs. (22.7 kg)

Approximate shipping weight 425 lbs. (193.2 kg)

36 All Refrigerator/Freezer Description DFFB536 DFRB536 Overall width 36 (91.5 cm) Overall height (from bottom) 82-3/4 (210.2 cm) min. to 84-1/16 (213.5 cm) max. Overall depth (from rear) To front edge of side trim: 23-13/16 (60.5 cm)

To front of top grille: 24-3/4 (62.9 cm) To front edge of door trim: 24 (61.0 cm)

Cutout width 36 (91.5 cm) Cutout height 82-7/8 (210.5 cm) min. to 84-1/16 (213.5 cm) max. Cutout depth 24 (61.0 cm) min.* Electrical requirements 115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with

grounded 3-prong plug attached to product Maximum amp usage 9.9 amps Inlet water requirements 1/4 copper tubing inlet

waterline; minimum 20 psi; N/A maximum 120 psi

Overall interior dimensions total capacity 19.1 cu. ft. (541 liters) 22.8 cu. ft. (646 liters) Maximum panel weight 60 lbs. (27.2 kg)

Approximate shipping weight 500 lbs. (227.3 kg)

30 All Refrigerator/Freezer

36 All Refrigerator/Freezer

*Note: Custom panel models fit flush in 25 (63.5 cm) deep cabinet openings. They can be installed in standard 24 (61.0 cm) deep openings. The door faces and top grille will protrude 3/4 (1.9 cm) into the room.

One 2x 4 mounting board 1-1/2 (3.8 cm) x 3-1/2 (8.9 cm)

Note: If unit is installed deeper than 24 (61.0 cm), then shim behind the mounting boards by the difference.

Bottom of anti-tip board is 3-7/8 (9.8 cm) below opening height. Note: Top of unit must be placed firmly under anti-tip board.

Anti-Tip Location

79-3/8(201.6 cm) min.to bottom ofanti-tip board

80-1/2(204.6 cm) max.to bottom ofanti-tip board

23 (58.4 cm)

3-1/2(8.9 cm)

1-1/2

(3.8 cm)

9(22.9 cm)

73-3/8(186.4 cm)

82-7/8(210.5 cm) min. anti-tip board &opening height

84-1/16(213.5 cm) max. anti-tip board & opening height

30(76.2 cm)

24 (61.0 cm) Electric Outlet Location

Water Line Entry Area Note: Shown for All Freezer only.

30(76.2 cm) 6-3/4(17.1 cm)

7-5/8(19.4 cm)

3(7.6 cm) 5/8(1.5 cm)

5/8(1.5 cm)

10-1/2(26.7 cm) 5/8(1.5 cm)

10-3/4(27.3 cm)

1 (2.5 cm)

3-5/8(9.2 cm)

Optional floor water line entry

See anti-tip board installation 6 (15.2 cm)

9 (22.9 cm)

2726

Cutout Dimensions (All Refrigerator/Freezer)

30 All Refrigerator/Freezer

Anti-Tip Dimensions (All Refrigerator/Freezer)

30 All Refrigerator/Freezer

One 2x4 mounting board 1-1/2 (3.8 cm) x 3-1/2 (8.9 cm) Note: If unit is installed deeper than 24 (61.0 cm), then shim behind the mounting board by the difference.

Bottom of anti-tip board is 3-7/8 (9.8 cm) below the opening height. Note: Top of unit must be placed firmly under anti-tip board.

One 2x 4 mounting board 1-1/2 (3.8 cm) x 3-1/2 (8.9 cm)

Note: If unit is installed deeper than 24 (61.0 cm), then shim behind the mounting boards by the difference.

Bottom of anti-tip board is 3-7/8 (9.8 cm) below opening height. Note: Top of unit must be placed firmly under anti-tip board.

Anti-Tip Location

79-3/8(201.6 cm) min.to bottom ofanti-tip board

80-1/2(204.6 cm) max.to bottom ofanti-tip board

29 (73.7 cm)

3-1/2(8.9 cm)

1-1/2

(3.8 cm)

9(22.9 cm)

73-3/8(186.4 cm)

82-7/8(210.5 cm) min. anti-tip board &opening height

84-1/16(213.5 cm) max. anti-tip board & opening height

36(91.5 cm)

24 (61.0 cm)

Electric Outlet Location

Water Line Entry Area Note: Shown for All Freezer only.

36(91.5 cm) 6-3/4(17.1 cm)

7-5/8(19.4 cm)

3(7.6 cm)

5/8(1.5 cm)

5/8(1.5 cm)

10-1/2(26.7 cm) 5/8(1.5 cm)

10-3/4(27.3 cm)

1 (2.5 cm)

3-5/8(9.2 cm)

See anti-tip board installation 6 (15.2 cm)

9 (22.9 cm)

Optional floor water line entry

2928

Cutout Dimensions (All Refrigerator/Freezer)

36 All Refrigerator/Freezer

Anti-Tip Dimensions (All Refrigerator/Freezer)

36 All Refrigerator/Freezer

One 2x4 mounting board 1-1/2 (3.8 cm) x 3-1/2 (8.9 cm) Note: If unit is installed de per than 24 (61.0 cm), then shim behind the mounting board by the difference.

Bottom f anti-tip board is 3-7/8 (9.8 cm) below the ope ing height. Note: Top of unit must be placed firmly under anti-tip board.

75-15/16 (192.9 cm)

3-1/2(8.9 cm) 30(76.2 cm)

29(73.7 cm)

29-1/2(74.9 cm)

1(2.54 cm) between units

35(88.9 cm)

82-7/8(210.5 cm)min. to84-15/16

(213.5 cm)max.

36(91.5 cm)

Measurement varies

(locally supplied hardware)

23-13/16

(60.5 cm)

24-3/4

(62.9 cm)

35-1/2(90.2 cm)

Dimensions (All Refrigerator/Freezer)

23-13/16

(60.5 cm)

24-3/4

(62.9 cm)

82-7/8(210.5 cm)min. to84-15/16

(213.5 cm)max.

Measurement varies

(locally supplied hardware)

30(76.2 cm)

29(73.7 cm)

75-15/16 (192.9 cm)

3-1/2(8.9 cm) 30(76.2 cm)

29(73.7 cm)

29-1/2(74.9 cm)

29-1/2(74.9 cm)

1(2.54 cm) between units

Dimensions (All Refrigerator/Freezer)

3130

Dual 30 All Refrigerator/Freezer Dual 30 & 36 All Refrigerator/Freezer

Specifications (All Refrigerator/Freezer)

75-15/16 (192.9 cm)

3-1/2(8.9 cm)

1(2.54 cm) between units

35(88.9 cm)

82-7/8(210.5 cm)min. to84-15/16

(213.5 cm)max.

36(91.5 cm)

Measurement varies

(locally supplied hardware)

23-13/16

(60.5 cm)

24-3/4

(62.9 cm)

35-1/2(90.2 cm)

35-1/2(90.2 cm)

35(88.9 cm)

36(91.5 cm)

Dimensions (All Refrigerator/Freezer)

3332

Dual All Refrigerator/Freezer* Description (2) 30 Units (1) 36 & (1) 30 Unit (2) 36 Units Overall width 60 (152.4 cm) 66 (167.6 cm) 72 (182.9 cm) Overall height (from bottom) 82-3/4 (210.2 cm) min. to 84-1/16 (213.5 cm) max. Overall depth (from rear) To front edge of side trim: 23-13/16 (60.5 cm)

To front of top grille: 24-3/4 (62.9 cm) To front edge of door trim: 24 (61.0 cm)

Cutout width 60 (152.4 cm) 66 (167.6 cm) 72 (182.9 cm) Cutout height 82-7/8 (210.5 cm) min. to 84-1/16 (213.5 cm) max. Cutout depth 24 (61.0 cm) min.** Electrical requirements (2) 115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with

grounded 3-prong plug attached to product Maximum amp usage 9.9 amps per unit Inlet water requirements 1/4 copper tubing inlet waterline; minimum 20 psi; (All Freezer only) maximum 120 psi Overall interior dimensions

30 freezer 15.9 cu. ft. (450 liters) 30 refrigerator 18.2 cu. ft. (516 liters) 36 freezer 19.1 cu. ft. (541 liters) 36 refrigerator 22.8 cu. ft. (646 liters)

Maximum panel weight 30 freezer or refrigerator 50 lbs. (22.7 kg)

36 freezer or refrigerator 60 lbs. (27.2 kg)

Approximate shipping weight 30 freezer or refrigerator 425 lbs. (193.2 kg) 36 freezer or refrigerator 500 lbs. (227.3 kg)

Dual 36 All Refrigerator/Freezer

*For installation of two units side-by-side, a separate grille kit accessory must be purchased.

**Note: Custom panel models fit flush in 25 (63.5 cm) deep cabinet openings. They can be installed in standard 24 (61.0 cm) deep openings. The door faces and top grille will protrude 3/4 (1.9 cm) into the room.

79-3/8(201.6 cm) min.to bottom ofanti-tip board

80-1/2(204.6 cm) max.to bottom ofanti-tip board

One 2x 4 mounting board per unit 1-1/2 (3.8 cm) x 3-1/2 (8.9 cm)

Note: If unit is installed deeper than 24 (61.0 cm), then shim behind the mounting boards by the difference.

Bottom of anti-tip board is 3-7/8 (9.8 cm) below opening height. Note: Top of unit must be placed firmly under anti-tip board.

Anti-Tip Location

23 (58.4 cm)

3-1/2(8.9 cm)

1-1/2

(3.8 cm)

23 (58.4 cm)

9(22.9 cm)

73-3/8(186.4 cm)

82-7/8(210.5 cm) min. anti-tip board &opening height

84-1/16(213.5 cm) max. anti-tip board & opening height

60(152.4 cm)

24 (61.0 cm) Electric outlet location

Water Line Entry Area Note: Cutout opening shown with All Freezer model on left.

Reverse water line entry if All Freezer model is on right.

60(152.4 cm) 6-3/4(17.1 cm)

7-5/8(19.4 cm) 3(7.6 cm)

5/8(1.5 cm)

5/8(1.5 cm)

10-1/2(26.7 cm) 5/8(1.5 cm)

10-3/4(27.3 cm)

3-5/8(9.2 cm)

1 (2.5 cm)

Optional floor water line entry

See anti-tip board installation 6

(15.2 cm)

9 (22.9 cm)

3534

Cutout Dimensions (All Refrigerator/Freezer)

Dual 30 All Refrigerator/Freezer

Anti-Tip Dimensions (All Refrigerator/Freezer)

Dual 30 All Refrigerator/Freezer

One 2x4 mounti g board per unit 1-1/2 (3.8 cm) x 3-1/2 (8.9 cm) Note: If unit is installed deeper than 24 (61.0 c ), then shim behind the mounting board by the difference.

Bottom of anti-tip board is 3-7/8 (9.8 cm) below the opening height. Note: Top of unit must be placed firmly under anti-tip board.

79-3/8(201.6 cm) min.to bottom ofanti-tip board

80-1/2(204.6 cm) max.to bottom ofanti-tip board

One 2x 4 mounting board per unit 1-1/2 (3.8 cm) x 3-1/2 (8.9 cm)

Note: If unit is installed deeper than 24 (61.0 cm), then shim behind the mounting boards by the difference.

Bottom of anti-tip board is 3-7/8 (9.8 cm) below opening height. Note: Top of unit must be placed firmly under anti-tip board.

Note: Dimensions shown for 36 All Freezer/All Refrigerator model on the left. Reverse mounting boards if units are installed on the right.

Anti-Tip Location

29 (73.7 cm)

3-1/2(8.9 cm)

1-1/2

(3.8 cm)

23 (58.4 cm)

9(22.9 cm)

73-3/8(186.4 cm)

82-7/8(210.5 cm) min. anti-tip board &opening height

841/16(213.5 cm) max. anti-tip board & opening height

66(167.6 cm)

24 (61.0 cm) Electric Outlet Location

Water Line Entry Area Note: Cutout opening shown with All Freezer model on left.

Reverse water line entry if All Freezer model is on right.

66(167.6 cm) 6-3/4(17.1 cm)

7-5/8(19.4 cm) 3(7.6 cm)

5/8(1.5 cm)

5/8(1.5 cm)

10-1/2(26.7 cm) 5/8(1.5 cm)

10-3/4(27.3 cm)

3-5/8(9.2 cm)

1 (2.5 cm)

Optional floor water line entry

See anti-tip board installation 6

(15.2 cm)

9 (22.9 cm)

3736

Cutout Dimensions (All Refrigerator/Freezer)

Dual 30 & 36 All Refrigerator/Freezer

Anti-Tip Dimensions (All Refrigerator/Freezer)

Dual 30 & 36 All Refrigerator/Freezer

One 2x4 mounting board per unit 1-1/2 (3.8 cm) x 3-1/2 (8.9 cm) Note: If unit is installed deeper than 24 (61.0 cm), then shim behind the mounting board by the difference.

Bottom of anti-tip board is 3-7/8 (9.8 cm) below the pening height. Note: Top of unit must be placed firmly under anti-tip board.

Note: Dim nsions show for 36 All Freez r/All R frigerator model on the left. Reverse mounting boards if untis are installed on the right.

79-3/8(201.6 cm) min.to bottom ofanti-tip board

80-1/2(204.6 cm) max.to bottom ofanti-tip board

One 2x 4 mounting board per unit 1-1/2 (3.8 cm) x 3-1/2 (8.9 cm)

Note: If unit is installed deeper than 24 (61.0 cm), then shim behind the mounting boards by the difference.

Bottom of anti-tip board is 3-7/8 (9.8 cm) below opening height. Note: Top of unit must be placed firmly under anti-tip board.

Anti-Tip Location

29 (73.7 cm)

3-1/2(8.9 cm)

1-1/2

(3.8 cm)

29 (73.7 cm)

Anti-Tip Dimensions (All Refrigerator/Freezer)

9(22.9 cm)

73-3/8(186.4 cm)

82-7/8(210.5 cm) min. anti-tip board &opening height

84-1/16(213.5 cm) max. anti-tip board & opening height

72(182.9 cm)

24 (61.0 cm) Electric Outlet Location

Water Line Entry Area Note: Cutout opening shown with All Freezer model on left.

Reverse water line entry if All Freezer model is on right.

72(182.9 cm) 63/4(17.1 cm)

7-5/8(19.4 cm) 3(7.6 cm)

5/8(1.5 cm)

5/8(1.5 cm)

10-1/2(26.7 cm) 5/8(1.5 cm)

10-3/4(27.3 cm)

3-5/8(9.2 cm)

1 (2.5 cm)

Optional floor water line entry

See anti-tip board installation 6

(15.2 cm)

9 (22.9 cm)

Cutout Dimensions (All Refrigerator/Freezer)

3938

Dual 36 All Refrigerator/Freezer Dual 36 All Refrigerator/Freezer

One 2x4 mounting board per it 1-1/2 (3.8 cm) x 3-1/2 (8.9 cm) Note: If unit is installed deeper than 24 (61.0 cm), then shim behind the mounting board by the difference.

Bottom of anti-tip board is 3-7/8 (9.8 cm) below the opening height. Note: Top of unit must be placed firmly under anti-tip board.

1/2(1.27 cm)

1-1/2

(3.81 cm)

1/4 Radius

(.64 cm)

2-3/4

(6.98 cm)

1/2(1.27 cm)

3/4(1.90 cm)

1/2

(1.27 cm)

1/8(.31 cm)

1/2(1.27 cm)

1/4 Radius

(1.2 cm)

.64

Reverse dimensions for other end.

7/8

(2.22 cm)

1/2 (1.27 cm)

2-1/8

(5.39 cm)

3-1/8

(7.94 cm)3-5/8 (9.20 cm)

1-3/8 (3.49 cm)

3/8

(.95 cm)

3/8 Radius (.95 cm)

29-1/2(74.93 cm)

1/2(1.27 cm)

3-1/8

(7.93 cm)

Optional hinge cover

1/2(1.27 cm)

3-5/8

(9.20 cm)

27-15/16 (70.96 cm)

28(71.12 cm)

28(71.12 cm)

3/4(1.90 cm)

3/4(1.90 cm)

3-3/4

(9.52 cm)

3-3/4

(9.52 cm)

3

(7.62 cm)

3

(7.62 cm)

3/4(1.90 cm) 26-3/16(66.51 cm)

5-17/32(14.10 cm)

4-11/64(10.59 cm)

24-27/32 (63.10 cm)

Custom Grille Dimensions (All Refrigerator/Freezer)

35-1/4(89.5 cm)

75-1/2(191.8 cm)

3/4

(1.9 cm)

29-1/4(74.3 cm)

75-1/2(191.8 cm)

3/4

(1.9 cm)

Overlay Dimensions (All Refrigerator/Freezer)

4140

30 Custom Panels

36 Custom Panels

30 Custom Grille

Note: Hardware placement can vary depending on single or dual installation.

Note: Panel overlays must be dry, solid, straight one piece panels. The use of multiple panel pieces to achieve the dimensions is not recommended.

Note: This part should be located at the center of the grille. If desired, two per grille can be used by dividing the length of the grille into thirds.

1/2(1.27 cm)

1-1/2

(3.81 cm)

1/4 Radius

(.64 cm)

2-3/4

(6.98 cm)

1/2(1.27 cm)

3/4(1.90 cm)

3/8 (0.38 cm)

1/2 (1.27 cm)

R 3/32 (0.09 cm)

3/4 (1.90 cm)

3/4 (1.90 cm)

3/4 (1.90 cm)

13/32 (1.03 cm)

9/16 (1.43 cm)

1/8 (.32 cm)

Grille support

2-7/8(7.30 cm)

1(2.54 cm)

1/2

(1.27 cm)

1/8(.31 cm)

1/2(1.27 cm)

1/4 Radius

(1.2 cm)

.64

Reverse dimensions for other end.

7/8

(2.22 cm)

1/2 (1.27 cm)

2-1/8

(5.39 cm)

3-1/8

(7.94 cm)3-5/8 (9.20 cm)

1-3/8 (3.49 cm)

3/8

(.95 cm)

3/8 Radius (.95 cm)

1/2(1.27 cm)

3-1/8

(7.93 cm)

Optional hinge cover

1/2(1.27 cm)

3-5/8

(9.20 cm)

3/4(1.90 cm)

3/4(1.90 cm)

3-3/4

(9.52 cm)

3-3/4

(9.52 cm)

3

(7.62 cm)

3

(7.62 cm)

3/4(1.90 cm)

59-1/2(151.13 cm)

58(147.32 cm)

57-15/16 (147.16 cm)

58(147.32 cm)

56-3/64 (142.36 cm)

54-27/32 (139.30 cm)

4-11/64(11.27 cm)

5-17/32(14.04 cm) 24-27/32 (63.01 cm)

26-3/16(66.80 cm)

34-11/64 (86.80 cm)

35-25/64 (89.90 cm)

Custom Grille Dimensions (All Refrigerator/Freezer)

2-1/8

(5.39 cm)

3-1/8

(7.94 cm)3-5/8 (9.20 cm)

1-3/8 (3.49 cm)

3/8

(.95 cm)

3/8 Radius (.95 cm)

Reverse dimensions for other end.

1/2(1.27 cm)

1-1/2

(3.81 cm)

1/4 Radius

(.64 cm)

2-3/4

(6.98 cm)

1/2(1.27 cm)

3/4(1.90 cm)

1/2

(1.27 cm)

1/8(.31 cm)

1/2(1.27 cm)

1/4 Radius

(1.2 cm)

.64

7/8

(2.22 cm)

1/2 (1.27 cm)34(86.36 cm)

34(86.36 cm)

3/4(1.90 cm)

1/2(1.27 cm)

3/4(1.90 cm)

3-3/4

(9.52 cm)

3-3/4

(9.52 cm)

3-5/8

(9.20 cm)

33-15/16 (86.20 cm)

3

(7.62 cm)

3

(7.62 cm)

3/4(1.90 cm)

35-1/2(90.17 cm)

1/2(1.27 cm)

3-1/8

(7.93 cm)

Optional hinge cover

32-3/16(81.75 cm)

5-17/32(14.10 cm)

4-11/64(10.59 cm)

30-27/32 (78.34 cm)

Custom Grille Dimensions (All Refrigerator/Freezer)

4342

36 Custom Grille Dual 30 Custom Grille

Note: Dual units can only be made in a left and right hand configuration.

Note: To use a custom grille on a dual installation, you must purchase the center trim kit FCTKSS.

Note: This part should be located at the center of the grille. If desired, two per grille can be used by dividing the length of the grille into thirds.

1/2(1.27 cm)

1-1/2

(3.81 cm)

1/4 Radius

(.64 cm)

2-3/4

(6.98 cm)

1/2(1.27 cm)

3/4(1.90 cm)

3/8 (0.38 cm)

1/2 (1.27 cm)

R 3/32 (0.09 cm)

3/4 (1.90 cm)

3/4 (1.90 cm)

3/4 (1.90 cm)

13/32 (1.03 cm)

9/16 (1.43 cm)

1/8 (.32 cm)

Grille support

2-7/8(7.30 cm)

1(2.54 cm)

1/2

(1.27 cm)

1/8(.31 cm)

1/2(1.27 cm)

1/4 Radius

(1.2 cm)

.64

Reverse dimensions for other end.

7/8

(2.22 cm)

1/2 (1.27 cm)

2-1/8

(5.39 cm)

3-1/8

(7.94 cm)3-5/8 (9.20 cm)

1-3/8 (3.49 cm)

3/8

(.95 cm)

3/8 Radius (.95 cm)

1/2(1.27 cm)

3-1/8

(7.93 cm)

Optional hinge cover

1/2(1.27 cm)

3-5/8

(9.20 cm)

3/4(1.90 cm)

3/4(1.90 cm)

3-3/4

(9.52 cm)

3-3/4

(9.52 cm)

3

(7.62 cm)

3

(7.62 cm)

3/4(1.90 cm)

71-1/2(181.61 cm)

70(177.80 cm

69-15/16 (177.64 cm)

70(177.80 cm)

68-3/64 (172.84 cm)

66-27/32 169.78 cm)

4-11/64(11.27 cm)

5-17/32(14.04 cm) 30-27/32 (78.34 cm)

32-3/16(81.75 cm)

40-11/64 (102.04 cm)

41-25/64 (105.13 cm)

Custom Grille Dimensions (All Refrigerator/Freezer)

Note: This part should be located at the center of the grille. If desired, two per grille can be used by dividing the length of the grille into thirds.

1/2(1.27 cm)

1-1/2

(3.81 cm)

1/4 Radius

(.64 cm)

2-3/4

(6.98 cm)

1/2(1.27 cm)

3/4(1.90 cm)

3/8 (0.38 cm)

1/2 (1.27 cm)

R 3/32 (0.09 cm)

3/4 (1.90 cm)

3/4 (1.90 cm)

3/4 (1.90 cm)

13/32 (1.03 cm)

9/16 (1.43 cm)

1/8 (.32 cm)

Grille support

2-7/8(7.30 cm)

1(2.54 cm)

1/2

(1.27 cm)

1/8(.31 cm)

1/2(1.27 cm)

1/4 Radius

(1.2 cm)

.64

Reverse dimensions for other end.

7/8

(2.22 cm)

1/2 (1.27 cm)

2-1/8

(5.39 cm)

3-1/8

(7.94 cm)3-5/8 (9.20 cm)

1-3/8 (3.49 cm)

3/8

(.95 cm)

3/8 Radius (.95 cm)

1/2(1.27 cm)

3-1/8

(7.93 cm)

Optional hinge cover

1/2(1.27 cm)

3-5/8

(9.20 cm)

3/4(1.90 cm)

3/4(1.90 cm)

3-3/4

(9.52 cm)

3-3/4

(9.52 cm)

3

(7.62 cm)

3

(7.62 cm)

3/4(1.90 cm)

65-1/2(166.37 cm)

64(162.56 cm)

63-15/16 (167.48 cm)

64(162.56 cm)

62-3/64 (157.60 cm)

60-27/32 (154.54 cm)

4-11/64(11.27 cm)

5-17/32(14.04 cm) 24-27/32 (63.10 cm)

26-3/16(66.51 cm)

34-11/64 (86.80 cm)

35-25/64 (89.90 cm)

Custom Grille Dimensions (All Refrigerator/Freezer)

4544

Dual 30 & 36 Custom Grille Dual 36 Custom Grille

Note: Dual units can only be made in a left and right hand configuration.

Note: To use a custom grille on a dual installation, you must purchase the center trim kit FCTKSS.

Note: 30 unit is on left and 36 unit is on right.

Note: Dual units can only be made in a left and right hand configuration.

Note: To use a custom grille on a dual installation, you must purchase the center trim kit FCTKSS.

Top View Flush mount cabinet doors

24 (61.0 cm) standard cabinet depth

24-3/4 (62.9 cm)

Cabinet door

Door

Wall

3/4 (1.9 cm)

full end panel

Flush

3/4 (1.9 cm) overlay panel

1/8 (0.3 cm)

foam

Cabinet Information

4746

Top View

Top View

Door

24 (61.0 cm) standard cabinet depth

25 (63.5 cm)

countertop depth

Wall

3/4 (1.9 cm)

full end panel

Door

Wall

1/4 (.63 cm) space if

25 (63.5 cm) cabinet depth

is used

3/4 (1.9 cm) full end panel25

(63.5 cm)

Flush

1/4 (.63 cm) space if

25 (63.5 cm) cabinet depth

is used

Flush

3/4 (1.9 cm) overlay panel

1/8 (0.3 cm)

foam

3/4 (1.9 cm) overlay panel

1/8 (0.3 cm)

foam

Cabinet Information Custom panel models, (with 3/4 [1.9 cm], thick panels and custom handles locally supplied), fit flush in 25 (63.5 cm) deep (countertop depth) cabinet openings with no protrusion into room except custom handles

Custom panel models can be installed in standard 24 (61.0 cm) deep openings. However, the door faces and top ventilation grille will protrude 3/4 (1.9 cm) into the room. This is ideal for alignment with full overlay cabinet doors.

3/4 (1.9 cm)

End panel

1 (2.5 cm)

1/4 (0.6 cm)

Z-Bracket

21-3/4

(55.2 cm)

21-3/4

(55.2 cm)

24

(61.0 cm)

Optional kickplate notch (Dimensions determined by cabinets) 24

(61.0 cm)

82-7/8 (210.5 cm) min.

to84-1/16 (213.5 cm) max.*

82-7/8 (210.5 cm) min.

to84-1/16 (213.5 cm) max.*

Custom Side Panel Dimensions

4948

*Note: Depending on how high leveling feet are raised, and cabinet enclosure height.

Custom Panel General Information Custom finishing options All installations must allow for the refrigerator and freezer door to open a minimum of 90.

For side wall or corner installation, allow for a standard 3 (7.6 cm) cabinet filler to assure door(s) opens 90.

Note: If a custom handle is used, a wider filler may be necessary.

Panel thickness must not exceed 1 (2.5 cm) on hinge side. Thicker panels will interfere with door swing and clearance.

Ice and Water Dispenser Bezel Removal (if required) Note: Designer model shown.

Remove packaging material surrounding bezel. Grasping the sliding lever, pull away from bezel.

Remove spill tray from lower part of bezel exposing 2 screws.

Remove screws.

1 2

43 Note: Adding 3/4 (1.9 cm) side panels adds an additional 3/4 (1.9 cm) to the overall width of the product for each side panel used.

Note: Requires side panel hardware kit (SPHKDS).

5150

Remove 2 additional screws under top section of bezel.

Remove mounting support.

Grasping the bezel on both sides, pull away from the door cavity.

Note: Bezel needs to be pulled from the bottom first and then pull slightly downward to clear

the water dispensing tube.

Store bezel and spill tray in safe and secure place until installation.

5 6

7 38

Remove handle side cabinet screws and trim with a phillips screwdriver.

Remove all screws from handle side door trim. Remove two screws from top and bottom door trim.

Remove handle side door trim.

Remove bracket. Measure and mark the first hole for each bracket.

Push custom wood panel onto door.

1

x13

2

x13

x2

x2

3 2-1/16 (5.2 cm)

Back of panel

FOL bracketZ bracket

1-11/16 (4.3 cm)

2-13/16 (7.1 cm)

Bottom-mount

12-1/16 (30.6 cm)

All Refrigerator/ Freezer/

Side-by-side

2-1/8 (5.4 cm)

4

5 x13

x13 SxS, AFAR x12 BTM

6

Custom Door Panel Installation (Refrigerator or Freezer)

Attach Z bracket to the hinge side of custom panel. Attach bracket to the handle side of custom panel.

Ice and Water Dispenser Bezel Removal (if required cont.)

5352

7

Open freezer door. Remove door trim screws and door trim with a phillips screwdriver.

Remove bracket.

1

x16

2

Attach bracket to the custom panel.

Align and slide custom wood panel onto door.

4 x13

5

Slide custom wood panel to the hinge side, ensuring Z bracket engages the door bracket.

8

x13

x2

x2

Reinstall handle side door trim and door trim screws.

Reinstall door trim and door trim screws.

6

x16

Custom Door Panel Installation (Refrigerator or Freezer cont.) Custom Freezer Door Panel Installation (Bottom-Mount Only cont.)

9

x13

Reinstall cabinet trim and screws. Measure and mark the first hole on each side of the bracket.

Back of panel

FOL bracket

2-1/16 (5.2 cm)

2-1/16 (5.2 cm)

1-11/16 (4.3 cm)

1-11/16 (4.3 cm)

3

5554

7 8

Adjust and reposition bezel as necessary. Tighten all screws securely.

Replace spill tray in lower part of bezel.

9

Align cube switch with sliding lever and firmly push until sliding lever is flush with bezel.

For a left hinge door, cut 5/8 x 2-3/4 in lower left corner. Note: Steps show panel upside down and notched for left hinge application. Mirror dimensions for right hinge door.

Position upper mounting support over holes underneath top section of bezel.

5 6

Ice and Water Dispenser Bezel Installation (if required) Ice and Water Dispenser Bezel Installation (if required cont.)

Push firmly into cavity until lower screw holes align with mounting holes on cavity.

Install two screws in lower part of bezel but DO NOT tighten all the way.

3 4

Install custom wood panels per products installation instructions.

Locate opening in door and position bezel. Note: Graphics on bezel will be on top end, tilt slightly

forward to allow water tube clearance.

1 2

Install Door Trim Insert

Use the roll of trim insert located in the drawer inside the unit to apply to the door trim.

1

5756

1 2

Remove air grille center blade. Remove two 1/4 (0.6 cm) screws with a magnetic extended screwdriver at least 8 (20.3 cm) long.

3 4

Pull air grille assembly forward. Remove 2 mounting brackets from the grille air assembly.

5 6

Using eight screws removed from the mounting brackets, attach mounting brackets to the custom wood grille using predrilled pilot holes. (See grille overlay specifications for

proper alignment and pilot hole placement.)

Insert custom air grille assembly.

Custom Grille Installation

Install two 1/4 (0.6 cm) screws with a magnetic extended screwdriver at least 8 (20.3 cm) long.

Install custom air grille center blade.

7 8

Custom Grille Installation (cont.)

Measure and cut 2-1/16 diagonal in lower left corner.

Cut out diagonal in lower left corner.

3(7.62 cm)

5/8(1.6 cm)

3

2 1

1

1-13/16 (4.60 cm)

2 3/32

(.24 cm)

5/8(1.6 cm)

3

3

2

1

Bottom-Mount Custom Panel Hinge Cutout (if required)

Final view of lower corner.

4

For a left hinge door, cut 5/8 x 3 in lower left corner. Note: Steps show panel upside down and notched for left hinge application. Mirror dimensions for right hinge

door.

58 59

General Information Area Requirements Verify the following: Unit can fit into residence and can be moved around corners and through doorways.

Floors can support units weight plus food weight (approximately 1200 pounds [540 kg] per unit).

Rear wall is solid and is able to support two horizontally mounted 2 x 4s (included) bolted to two wall studs. The 2 x 4 board bolt heads must be flush with 2 x 4 to prevent obstruction.

Remove anything attached to rear or side walls that can obstruct unit installation.

Cutout dimensions are accurate.

Electrical outlet is in correct location.

Water line is in correct location.

DO NOT install a refrigeration unit near a heat source, nor in a location where the surrounding temperature will fall below 60 F (16 C).

Electrical Requirements It is the customers responsibility to: Contact a qualified electrical installer. Assure that the electrical installation is adequate and in conformance with the National Electrical Code, ANSI/NFPA 70-latest edition or Canadian Electrical Code C22.1-1998 and C22.2 No. 0-M91 (or latest edition), and all local

codes and ordinances. A 115 volt, 60-Hz, 15 amp, fused, electrical supply is required. It is required that a separate circuit serving only this appliance be provided. This appliance is equipped with a power supply cord having a 3-prong grounding plug. To minimize possible shock hazard, the cord must be plugged into a mating 3-prong, grounding-type wall receptacle. DO NOT use an extension cord.

If codes permit a separate grounding wire to be used, it is recommended that a qualified electrician determine that the grounding path is adequate.

DO NOT ground to a gas line. Check with a qualified electrician if you are not sure if the appliance is properly grounded. DO NOT have a fuse in the neutral or grounding circuit.

Anti-Tip Requirements The anti-tip boards should be fastened into position prior to moving the unit into the opening.

Note: Additional mounting boards may be required if the unit does not touch the back wall of the enclosure. To prevent unit from tipping forward, it must be secured in place with a solid soffit or wood block.

General Information

Water Supply Requirements

Use only 1/4 (6 mm) copper tubing for water line. DO NOT install copper tubing in area where temperatures drop below 35 F (1.7 C). Before attaching copper tubing to the unit, flush at least 2 quarts (1.9 L) of water through the copper tubing and into a bucket to remove any particles in the water line.

Viking Range Corporation is not responsible for property damage due to improper installation or water connection.

Connect 1/4 (6 mm) flexible copper tubing to household plumbing in compliance with local codes and ordinances.

Length of copper tubing must reach from water supply connection to the unit connection with an additional length to facilitate moving the unit out of enclosure for cleaning or service. Tubing should be soft instead of rigid and ends should be free of burrs.

Copper tubing route must be above 35 F (1.7 C) to prevent water line from freezing.

DO NOT use plastic water lines from the household plumbing to the water inlet valve connection on the refrigeration unit.

DO NOT use the self-piercing feature of a saddle valve. The hole made by the piercing lance is too small for the water flow rate required by the ice maker.

If saddle valve is not used, place a separate shut-off valve in an easily accessible location between water supply and the unit. DO NOT install shut-off valve behind the unit.

The installation of Viking units with a reverse osmosis system is acceptable as long as the water pressure remains within the allowable PSI as stated below. It is important to note that with many reverse osmosis systems, the pressure starts off high, but then it decreases as the water level of the reverse osmosis storage area drops. This must be considered when checking the water pressure coming into the unit.

Connect a vertical or horizontal 1/2 (1.2 cm) to 1-1/4 (3.2 cm) COLD water line near water area.

Run water line through the floor, back, or side wall. Tubing should lay flat on floor underneath the unit. Clamp tubing to wall or floor.

Water pressure must be greater than 20 psi and less than 120 psi on non-dispensers and greater than 35 psi and less than 120 psi on dispensers.

To avoid serious illness or death, DO NOT use unit where water is microbiologically unsafe or of unknown quality, without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected water that may contain filterable cysts. The contaminants or other substances removed or reduced by this water treatment system are not necessarily in your water.

WARNING

6160

General Information Most of the units weight is at the top. Extra care is needed when moving the unit to prevent tipping.

DO NOT remove protective film until unit is in operating position.

All four leveling legs must make contact with the floor to support and stabilize the full weight.

DO NOT drop unit.

Remove exterior shipping materials prior to moving unit into home.

Use two or more people to move and install unit. Failure to follow this instruction can result in back or other injury.

To avoid personal injury, wear gloves when performing any installation procedure and wear eye protection when cutting metal straps.

Tip Over Hazard Appliance is top heavy and tips easily when not completely installed. Keep doors closed until appliance is completely installed and secured per installation instructions. Use two or more people to move and install the appliance. Failure to do so can result in death or serious injury.

Unpacking unit 1. Remove top and bottom strap.

2. Remove top cap.

3. Cut rear of carton approximately 1/4 (0.6 cm) to 1 (2.5 cm) from right corner with a utility knife extended 1/4 (0.6 cm).

4. Remove carton and exterior packaging. Save cardboard shipping material to protect floor surface when installing unit. Remove anti-tip board, kickplate and door trim pieces (DF models) from rear of unit.

Moving Unit

1 2

Remove shipping brackets from skid by removing four bolts (two on each side) with a

1/2 deep-well socket wench and a pair of pliers. Note: Tilting unit is not required to remove

shipping brackets.

Slip cart between unit and skid. Remove unit from skid. Note: Use excess packaging to protect decorative trim; also, verify that leveling legs are up (0 adjustment).

1 2a Professional

Place unit in front of cutout. Lift center grille louver up and pull out.

2b Designer 3

Pull the center grille louver up at an angle and pull out.

Using an 8 magnetic nut driver, remove the two 1/4 screws.

4

Remove grille assembly.

Installation

6362

Remove four side screws and remove unit top. Loosen the four hinge screws. Adjust door. Retighten four hinge screws.

Replace unit top and four side screws. Attach one 2 x 4 to wall stud (refer to dimensions page for exact location).

If needed, depending on cabinet and depth, attach second 2 x 4 to first 2 x 4.

2

1

5 Front of unit

2

1 3

6

1

2

7 8a

Wall

2 x 4

Refrigerator

8b

Wall

2 x 4

Refrigerator

Hinge Adjustment

9

Plug in power cord to verify operation. Note: Make sure power switch and

showroom switch are in the On position.

3

10a

Place unit within 3 of being flush with cabinets. Note: To avoid cabinet damage, place cardboard between cabinets and unit. When moving unit, DO NOT crimp, kink or crush water supply line.

10b

11

Carefully move unit until semi flush with cabinet (depending on unit).

Pull supply tubing forward under unit. Note: DO NOT use plastic water lines.

12

13

Flush water line by running two quarts of water into a bucket. Turn water off

Connect supply tube to water valve using a 1/2 wrench. Note: DO NOT overtighten.

Turn on water supply and check for leaks.

14

Installation (cont.)

6564

Lift unit off rollers to desired height and level unit using a 5/16 head wrench. Note: DO NOT use an electric device. Overtightening can cause damage.

Attach positive secure self-tapping bolts to 2 x 4 using a 22 extension.

Verify that drain pan is installed and aligned.

Align holes on both ends of louvered panels and insert screws.

Using a phillips screwdriver, attach the kickplate to the unit and adjust to desired height.

15

Wall

2 x 4

Refrigerator

Screw

16

17

1

2

18

21

3

19

Kickplate Installation

3

1

2

20

1

2

21

110 90

120

Open refrigerator door so door stop and shoulder screw are accessible.

Note: Shoulder screw should be in 110 door opening position.

Remove shoulder screw and place in 90 or 120 position.

3

1 2

22

1

2

23

110

90

120

Open refrigerator door so door stop and shoulder screw are accessible.

Note: Shoulder screw should be in 110 door opening position.

Remove shoulder screw and place in 90 or 120 position.

Door Stop Adjustment (Side-by-Side/All Refrigerator/All Freezer)

Door Stop Adjustment (Bottom-Mount)

Hinge Adjustment (cont.)

6766

Locate water filter door. The door is located under the adjustable cold zone handle.

Push upper left corner of door to release latch and pull door downward.

Insert filter cartridge into circular opening in filter housing. Rotate clockwise gently until

filter stops.Close water filter door.

Flush 3 gallons through filter before use (flush approximately 3 minutes). If water spurts occur, continue to run water until water runs steady.

Additional flushing may be required in areas with poor quality water.

NOTE: Allow 1-2 minute delay in water dispersal to allow internal water tank to fill.

24

2

1

25

1 3

2

26 27

Water Filter Installation (Side-by-Side with Dispenser)

Water Filter System Specification and Performance Data Sheet

This system has been tested according to NSF/ANSI 42/53 for reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration of less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI 42/53.* (100% safety factors built- in for unmetered usage for health claims only.)

*Based on the use of Cryptosporidium parvum oocysts

Operating Specifications Capacity: Certified for up to 750 gallons (2,838 L); up to nine months Pressure Requirement: 20 - 120 psi (1.4 - 8.2 bar) Temperature: 33-100oF (0.6 - 37.8oC) Flow rate: 0.78 gpm (2.9 l/min.)

Check for compliance with the state and local laws and regulations. Note: While the testing was performed under standard laboratory conditions, actual performance may vary. Must be installed and operated in accordance with manufacturers recommended procedures and guidelines. Installation instructions, parts and service availability, and standard warranty are included with the product when shipped. This drinking water system must be maintained according to manufacturers instruction, including replacement of filter cartridges.

Manufactured by: 3M Purification Inc. 400 Research Parkway Meriden, CT 06770

System tested and certified by NSF International against Standard 42 for the reduction of chlorine taste and odor, particulate Class I and Standard 53 for the reduction of Lead, Lindane, Atrazine, Mercury, Toxaphene, Cyst, Turbidity, and Abestos.

Contaminant Reduction

Average Influent

NSF Specified Challenge

Concentration

Avg % Reduction

Average Product Water Concentrtation

Max Permissible Product Water Concentration

NSF Reduction

Requirements

NSF Test Report

Chlorine Taste and Odor

2.0 mg/L 2.0 mg/L + 10% 97.5% 0.05 mg/L N/A > 50% J-00056501

Nominal Particulate Class I, >0.5 to < 1.0 m

13,666,667 pts/mL

At least 10,000 particles/mL

98.9% 143,333 pts/mL N/A > 85% J-00056506

Asbestos 96 MF/L 107 to 108 fibers/L; fibers greater than 10m in length

>99% <1 MF/L N/A > 99% J-00056511

Atrazine 0.010 mg/L 0.009 mg/L + 10% 89.3% 0.001 mg/L 0.003 mg/L N/A J-00056512

Cyst* 122,500 cysts/L

Minimum 50,000 cysts/L

99.99% 1 cyst/L N/A > 99.95% J-00056513

Lead @ pH 6.5 0.153 mg/L 0.15 mg/L + 10% 99.3% 0.001 mg/L 0.010 mg/L N/A J-00056515

Lead @ pH 8.5 0.150 mg/L 0.15 mg/L + 10% 99.3% 0.001 mg/L 0.010 mg/L N/A J-00058784

Lindane 0.002 mg/L 0.002 mg/L + 10% 97.8% 0.00004 mg/L 0.0002 mg/L N/A J-00058969

Mercury @ pH 6.5 0.006 mg/L 0.006 mg/L + 10% 95.0% 0.0003 mg/L 0.002 mg/L N/A J-00058785

Mercury @ pH 8.5 0.006 mg/L 0.006 mg/L + 10% 88% 0.0007 mg/L 0.002 mg/L N/A J-00058783

Toxaphene 0.015 mg/L 0.015 mg/L + 10% 93.2% 0.001 mg/L 0.003 mg/L N/A J-00056531

Turbidity 10.8 NTU 11 + 1 NTU 98.7% 0.153 NTU 0.5 NTU N/A J-00058972

6968

Replace top air grille. Using an 8 magnetic nut driver, replace the two 1/4 screws.

Replace the center grille louver. Replace the center grille louver.

Open door. The display should flash. Press ACTIVATE CONTROLS pad and close door.

Note: There is a 6 minute delay before the unit starts.

28 29

30a Professional 30b Designer

31 32

Final Installation

Performance Checklist

h Verify cabinet size.

h Verify electrical supply and water supply (if applicable).

h Install anti-tip device(s) and verify unit is secure.

h Position unit in cutout, level at desired height and secure unit.

h Plug-in unit and verify operation.

h Connect water supply (if applicable). Verify icemaker fill tube is properly inserted.

Verify icemaker bail arm is down. Verify dispenser operation (if applicable).

h Align/square door(s).

h Verify drain pan is properly installed and there are no leaks on water connection.

h Install kickplate.

h Remove internal packaging and labels and wipe unit down.

Installers information:

Installers name:_____________________________

Installers company:_________________________

Date: ________________________________________

7170

Verify Operations Verify Operations

Control Panels

1. Press Activate Controls pad 2. Verify unit is not in Sabbath Mode If in Sabbath Mode: A. The Sabbath Mode will disable the interior lights, display (except 3 blue squares) and alarm.

(See picture below for visual indication of Sabbath Mode)

To exit the Sabbath Mode: B. Press & Hold Activate Controls and then Display Off for 3 seconds.

(The control will beep 3 times to alert the user the Sabbath Mode has been exited) 3. Verify unit is not in Showroom Mode If in Showroom Mode: A. The Showroom Mode will disable the refrigerator system but all other functions are normal.

These include lights and control. (See picture below for visual indication of Showroom Mode)

To exit Showroom Mode: B. Press & Hold Activate Controls; while holding, press and hold Higher Temp and Alarm Off

together. (The control will beep 3 times to alert the user that Showroom Mode has been exited) 4. Press Alarm Off & Display Off at the same time and hold until beeps (force start compressor). 5. All models need to be set at the 5th bar for Refrigerator & Freezer factory setting.

Bottom-Mount

Side-by-Side

Control Panels

1. Press Activate Controls pad 2. Verify unit is not in Sabbath Mode If in Sabbath Mode: A. The Sabbath Mode will disable the interior lights, display (except 3 blue squares) and alarm. (See

picture below for visual indication of Sabbath Mode)

To exit the Sabbath Mode: B. Press & Hold Activate Controls and then Display Off for 3 seconds.

(The control will beep 3 times to alert the user the Sabbath Mode has been exited) 3. Verify unit is not in Showroom Mode If in Showroom Mode: A. The Showroom Mode will disable the refrigerator system but all other functions are normal.

These include lights and control. (See picture below for visual indication of Showroom Mode)

To exit Showroom Mode: B. Press & Hold Activate Controls; while holding, press and hold Higher Temp and Alarm Off

together. (The control will beep 3 times to alert the user that Showroom Mode has been exited) 4. Press Alarm Off & Display Off at the same time and hold until beeps (force start compressor). 5. All models need to be set at the 5th bar for Refrigerator & Freezer - factory setting.

All Refrigerator

All Freezer

7372

Only authorized replacement parts may be used in performing service on the appliance. DO NOT repair or replace any part of the appliance unless specifically recommended in the manual. All other servicing should be referred to a qualified technician.

Record the following information indicated below. You will need it if service is ever required. The serial number and model number for your appliance are located on the identification plate mounted on the bottom left side of the door opening.

Model number

_________________________________________

Serial number

_________________________________________

Date of purchase

_________________________________________

Date installed

_________________________________________

Dealer's name

_________________________________________

Address

_________________________________________

Service & Registration Notes ________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

_________________________________________________________________________________________________________________

Manualsnet FAQs

If you want to find out how the DFFB536 Viking works, you can view and download the Viking DFFB536 Refrigerator Installation Guide on the Manualsnet website.

Yes, we have the Installation Guide for Viking DFFB536 as well as other Viking manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Installation Guide should include all the details that are needed to use a Viking DFFB536. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Viking DFFB536 Refrigerator Installation Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Viking DFFB536 Refrigerator Installation Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Viking DFFB536 Refrigerator Installation Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Viking DFFB536 Refrigerator Installation Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Viking DFFB536 Refrigerator Installation Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.