Contents

Viking DDOE305T Oven Installation Guide PDF

1 of 10
1 of 10

Summary of Content for Viking DDOE305T Oven Installation Guide PDF

Viking Installation Guide

Designer Series Built-In Electric Single and Double Ovens

Viking Range Corporation

111 Front Street

Greenwood, Mississippi 38930 USA

(662) 455-1200

For product information,

call 1-888-VIKING1 (845-4641)

or visit the Viking Web site at

vikingrange.com

F20670D EN (080410)

IMPORTANT Before beginning installation, read these

instructions thoroughly and carefully.

DO NOT remove permanently affixed labels, warnings or plates from the product as this may void the warranty.

Observe all local and national codes, requirements and ordinances.

Installation must conform with local codes or in the absence of codes, the National Electrical Code, ANSI/NFPA-70 latest edition, or Canadian Electrical Code, CSA C22.1-1982 and C22.2 No. 01982 latest edition, National Fuel Gas Code ANSIZ223.1/NFPA-54 latest edition and all local codes and ordinances.

IN MASSACHUSETTS: This appliance must be installed by a Massachusetts licensed plumber or electrician.

IN CANADA: Installation must be in accordance with the current CSA C22.1 Canadian Electrical Codes Part 1 and/or local codes.

Installers should leave these instructions with the consumer who should retain them for the local inspectors use and for future reference.

3

Please Read and Follow

Your safety and the safety of others is very important.

We have provided many important safety messages in this manual and on your appliance. ALWAYS read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to hazards that can kill or hurt you and others.

All safety messages will be preceded by the safety alert symbol and the word DANGER, WARNING or CAUTION. These words mean:

Hazards or unsafe practices which WILL result in severe personal

injury or death

DANGER

Hazards or unsafe practices which COULD result in severe personal

injury or death

Hazards or unsafe practices which COULD result in minor personal injury

or property damage. All safety messages will identify the

hazard, tell you how to reduce the chance of injury, and tell you what can happen if

the instructions are not followed.

WARNING

CAUTION

Table of Contents

Warnings & Important Safety Information_______________________________________________3 Dimensions _________________________________________________________________________5 Specifications _______________________________________________________________________6 Cutout Dimensions __________________________________________________________________7 Flush Mount Installation ______________________________________________________________8 Electrical Requirements _____________________________________________________________10 General Information ________________________________________________________________11 Installation_________________________________________________________________________12 Final Preparation ___________________________________________________________________15 Performance Checklist ______________________________________________________________16 Service & Registration_______________________________________________________________18

Site Preparation: It is recommended that a thorough site inspection be conducted PRIOR to unpacking and moving this appliance.

Note: Wiring diagram is located on top of oven or in control panel.

Dimensions

5

IMPORTANT

4

Please Read and Follow

WARNING The misuse of the oven door(s) (e.g. stepping, sitting, or leaning on them) can result in hazards or injuries and damage to the product.

WARNING ELECTRICAL GROUNDING INSTRUCTIONS This oven must be electrically grounded in accordance with local codes or, in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70 latest edition.

WARNING Frame grounded by a 4-conductor cable assembly. See installation section.

DO NOT USE AN EXTENSION CORD WITH THIS APPLIANCE. SUCH USE MAY RESULT IN FIRE, ELECTRICAL SHOCK OR OTHER PERSONAL INJURY.

WARNING This appliance should not be used for space heating. This information is based on safety considerations.

WARNING The use of cabinets for storage above the oven may result in potential fire or burn hazard.

CAUTION The oven is heavyuse extreme care when handling.

51-3/8 (130.5 cm)

25-3/16

(64.0 cm) 25-3/16

(64.0 cm)

29-3/4 (75.6 cm)

29-3/4 (75.6 cm)

29-3/8 (74.6 cm)

23-1/2 (59.7 cm)

46-3/16 (117.3 cm)

21-1/4 (53.9 cm)

30 Single Oven 30 Double OvenWARNING DO NOT use the handle or oven door to lift the oven. Remove door before installation to ensure that it is not used to lift the unit. See installation section for door removal.

Cutout Dimensions (For standard installation and flush mount* installations)

7

Specifications

6

Designer Ovens Description DSOE301/DSOE305T DDOE301/DDOE305(T)

Overall width 29-3/4 (75.6 cm)

Overall height 29-3/8 (74.6 cm) 51-3/8 (130.5 cm)

Overall depth To front of door 25-3/16 (64.3 cm)

Cutout width Standard28-1/2 (72.4 cm minimum) Flush mount*29-5/8 (75.25 cm)

Cutout height Standard28-1/4 (71.8 cm) Flush mount*29-1/2 (74.9 cm)

Standard50-5/8 (128.6 cm) Flush mount*51-1/2 (130.8 cm)

Cutout depth Standard24 (61.0 cm) Flush mount*25-1/4 (64.1 cm)

Electrical requirements 4-wire ground, 240 VAC, 30 amp electrical connection for single ovens/ 50 amp for double ovens. Unit is equipped with No. 10 ground wire in conduit.

Should be fused separately. Maximum amp usage 23.3 amps240 VAC

20.2 amps208 VAC 46.7 amps240 VAC 40.5 amps208 VAC

Oven interior width 25 (63.5 cm)

Oven interior height 16 (40.6 cm)

Oven interior depth 18-1/2 (50.0 cm)

Oven volume (measured to AHAM Standard)**

3.8 cu. ft. DDOE305(T) Upper and Lower3.8 cu. ft. DDOE301 Upper 3.8 cu. ft. DDOE301 Lower4.0 cu. ft.

Oven volume (total oven cavity) 4.3 cu. ft.

*Note: To install the oven in a flush mount application the flush mount accessory kit (D30FTS for single ovens and D30FTD for double ovens) is required.

**Note: The AHAM Standard for measuring oven capacity subtracts the door plug and convection baffle dimension from the total oven volume.

28-1/2

(72.4 cm)

Flush mount

29-5/8

(75.2 cm)

24(61.0 cm)Flush mount 25-1/4 (64.1 cm)

28-1/4 (71.8 cm)Flush mount 29-1/2 (74.9 cm)

5 min. (12.7 cm)

Junction box location 17(43.2 cm)

28-1/2

(72.4 cm)

Flush mount

29-5/8

(75.2 cm)

28-1/4

(71.8 cm)

Flush mount

29-1/2

(74.9 cm)24(61.0 cm)Flush mount 25-1/4 (64.1 cm)

28-1/2

(72.4 cm)

Flush mount

29-5/8

(75.2 cm)

50-5/8

(128.5 cm)

Flush mount

51-1/2

(130.8 cm)

15-1/4

(38.7 cm) min.

to floor

4

(10.2 cm)

5 min. (12.7 cm)

Junction box location

4-3/4

(12.1 cm)

(Floor to botto

m

of cutout)

5 min. (12.7 cm)

Junction box location

4

(10.2 cm)

24(61.0 cm)Flush mount 25-1/4 (64.1 cm)

4(10.2 cm)

30 Single Oven Built-In30 Double Oven Built-In

30 Single Oven Undercounter

*Note: To install the oven in a flush mount application the flush mount accessory kit (D30FTS for single ovens and D30FTD for double ovens) is required.

Dimensions (Flush mount installation)

9

Dimensions (Flush mount installation)

8

FLUSH CUTOUT D 29-5/8 (75.2 cm)

E 25-1/4 (64.1 cm)

F 29-1/2 (74.9 cm)

Finished Surfaces

Vertical Blocking

B A

C

FLUSH CUTOUT A 29-5/8 (75.2 cm)

B 25-1/4 (64.1 cm)

C 51-1/2 (130.8 cm)

Finished Surfaces

Vertical Blocking

E D

F

LEGEND

Blocking

Finished Surfaces

ScrewScrew

Vertical Blocking

Distance will vary depending on the cabinet

A

B

Top View

CRITICAL DIMENSIONS

A 28-1/2 (72.4 cm)

B 1-1/2 (3.8 cm)

*Note: To install the oven in a flush mount application the flush mount accessory kit (D30FTS for single ovens and D30FTD for double ovens) is required.

General Information All openings in the wall behind the

appliance or in the floor under the appliance should be sealed.

Keep appliance area clear and free from combustible materials, gasoline and other flammable vapors.

Disconnect the electrical supply prior to servicing or cleaning.

When removing the appliance for cleaning or service, disconnect AC power supply and carefully remove the appliance by pulling forward.

Electrical requirements are listed in the product specifications under the electrical requirements section.

Recommendations for Unpacking Products are shipped on pallets with foam

footings and corrugated inner-packing and exterior hoods.

Products are anchored to the pallet using metal straps that are screwed to the bottom of the product and the pallet.

DO NOT remove protective packaging until you are ready to perform the installation.

To remove the packaging, first remove the staples located at the bottom perimeter of the corrugated cover.

Remove the corrugated cover by lifting it off the product and remove the inner- packing.

Detach the product from the metal anchor strip by removing the attachment screw.

DO NOT remove the protective wrapping from the product control panel until the product is installed.

Recommendations for Moving

Only proper equipment should be used to move products.

ALWAYS take steps to protect flooring at the installation location when moving products.

11

WARNING DO NOT use the handle or oven door to lift the oven. Remove door before installation to ensure that it is not used to lift the unit. DO NOT lift or carry the door by the handle.

CAUTION The oven is heavyuse extreme care when handling.

Electrical Requirements Oven requires a separate, grounded

4-wire, 240V (AC), 30 amp (single ovens) and 50 amp (double ovens) service with its own circuit breaker.

Wire sizes and connections must conform with the rating of the appliance and to the requirements of the National Electrical Code, ANSI/NFPA 70 latest edition, or Canadian Electrical Code, CSA C22.1-1982 and C22.2 No. 01982 latest edition, and all local codes and ordinances.

Oven must be connected to the proper electrical voltage and frequency as specified on the model/serial rating plate (located inside the vent ont the right sode of the oven).

Oven must be connected to grounded metal permanent wiring system. Check with a qualified electrician to make sure the oven is properly grounded.

DO NOT ground to a gas pipe.

DO NOT use an extension cord with this appliance, because this may result in electrical shock or other personal injury.

This unit is equipped with a No. 10 ground wire in the conduit.

The electrical conduit must be kept to the top left for a flush installation. NEVER cut the conduit.

Connect the flexible armored cable directly to 4-wire, 240V household service. If codes permit and separate grounding wiring is used, we recommend that a qualified electrician determine the grounding path and that the wire gauge is in accordance with local codes.

Junction boxes installed on rear wall directly behind oven must be recessed .

A UL-Listed conduit connector must be provided at the junction box.

DO NOT install a fuse in the neutral or grounding circuit. We recommend a time- delayed fuse or circuit breaker. Connect directly to the fused disconnect (or circuit breaker box) through flexible armored, or non-metallic sheathed, copper cable (with grounding wire).

10

13

3 4

Close the door until it stops. Push in/lift door up/and then out. Repeat for all doors.

5 6

Remove racks. Unscrew pallet screws from side of oven.

Neutral Green White

Black

Red

7a

Neutral

Green

White

Black

Red

7b

Wiring option 1* (connect the white and green to the incoming neutral)

Wiring option 2* (connect the white to the incoming neutral,

attach green to grounded junction box)

Installation (cont.)

*Note: Check local code to see which wiring option should be used when grounding the unit.

12

1

1

2

2

Remove wooden brace on front of pallet. Open door completely. Rotate door hinge to unlocked position.

Installation

General Information Site Preparation Note: It is recommended that a thorough site inspection be conducted PRIOR to unpacking and moving this appliance.

Confirm available access to adequate powersee electrical requirements.

Single oven units require a 30 amp circuit

Double oven units require a 50 amp circuit

Note: A minimum of 2 spacing above and below the oven to any adjacent items is required for ventilation purposes.

It is recommended that 3/4 or thicker material be utilized to create a support platform for this appliance.

BE SURE that support for this appliance is perpendicular to the front facing of the wall or cabinet before you perform the installation.

Use of a hydraulic lift is recommended for the installation of double oven units. Be careful not to bend lower trim/vent.

All openings in the wall behind the appliance or in the floor under the appliance should be sealed.

Keep appliance area clear and free from combustible materials, gasoline and other flammable vapors.

WARNING DO NOT use the handle or oven door to lift the oven. Remove door before installation to ensure that it is not used to lift the unit. DO NOT lift or carry the door by the handle.

WARNING FIRE OR ELECTRICAL SHOCK HAZARD DO NOT use an extension cord with this appliance. Such use may result in fire, electrical shock or other personal injury.

15

1

13

2

14

Open door completely. Rotate door hinge to locked position.

Close door.

Installation

1. Some stainless steel parts may have a protective wrap, which must be peeled off. All stainless steel body parts should be wiped regularly with hot, soapy water at the end of each cooling period and with liquid cleaner designed for this material when soapy water will not do the job. If build-up occurs, DO NOT use steel wool, or abrasive cloths, cleaners, or powders. If it is necessary to scrape stainless steel surface to remove encrusted material, soak area with hot, wet towels to loosen the material, then use a wooden or nylon spatula or scraper. DO NOT use a metal knife, spatula, or any other metal tool to scrape stainless steel surfaces. Scratches are almost impossible to remove.

2. The interior of the oven should be washed thoroughly with hot, soapy water to remove film residues and installation debris before being used for food preparation, then rinsed and wiped dry. Solutions stronger than soapy water are rarely needed.

Final Preparation

14

Neutral Green

White

Black

Red

7c 8

Wiring option 3* (connect the white to the incoming neutral,

attach green to suitable ground)

Lift oven into position.

9 10

Push oven straight in. Attach screws to the side of the framing. Note: Two screws for single ovens, four screws

for double ovens (screws not included).

11 12

Replace racks. Replace door.

Installation (cont.)

*Note: Check local code to see which wiring option should be used when grounding the unit.

Performance Checklist (cont.)

17

Electronic Timing Center

Off/On Indicator Light

Interior Oven Light Control

Temperature Control

Self-Clean Indicator Light

Oven Function Selector

Function Keys

Electronic Timing Center

Control Panel Lock

Digital Input Keys

Digital Display

Interior Oven Light

Control

Performance Checklist A qualified installer should carry out the following checks:

h Check oven Bake Functionbake element on full power, center and outside broil elements at partial power. Convection Bake functionbake and broil elements the same with the convection fan ON.

h Check TruConvec functionTruConvec element (behind convection fan cover) ON and convection fan ON.

h Check High Broil functionboth broil elements at full power. Convection broil function is the same with convection fan ON.

h Check Medium Broil functioninner and outer broil elements pulse on and off.

h Check Low Broil functioninner broil element only.

h Check Self-Clean functionDoor will lock in approximately 30 seconds, the center and outside broil elements will turn ON and the bake element will turn ON at partial power. Check broil elements through window to make sure they are ON, then abort self-clean cycle to unlock door.

Any adjustments necessary that are a result of the installer not following instructions will be the responsibility of the installer, dealer, or the end user of the product.

16

CAUTION DO NOT run self-clean cycle check for more than 10 minutes with the oven racks and rack supports inside oven to avoid discoloration due to the high temperature.

Designer Series

Designer SeriesTouch Control

19

Notes ________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

18

Service Information If service is required, call your dealer or authorized service agency. The name of the authorized service agency can be obtained from the dealer or distributor in your area.

Have the following information readily available. Model number Serial number Date purchased Name of dealer from whom purchased

Clearly describe the problem that you are having. If you are unable to obtain the name of an authorized service agency, or if you continue to have service problems, contact Viking Range Corporation at 1-888-VIKING1 (845-4641), or write to:

VIKING RANGE CORPORATION PREFERRED SERVICE

1803 Hwy 82W Greenwood, Mississippi 38930 USA

Record the information indicated below. You will need it if service is ever required. The model and serial number for your oven can be found by opening the door and looking underneath the control panel on the left hand side.

Model no. _____________________________Serial no. ________________________________

Date of purchase ___________________ Date installed ______________________

Manualsnet FAQs

If you want to find out how the DDOE305T Viking works, you can view and download the Viking DDOE305T Oven Installation Guide on the Manualsnet website.

Yes, we have the Installation Guide for Viking DDOE305T as well as other Viking manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Installation Guide should include all the details that are needed to use a Viking DDOE305T. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Viking DDOE305T Oven Installation Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Viking DDOE305T Oven Installation Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Viking DDOE305T Oven Installation Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Viking DDOE305T Oven Installation Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Viking DDOE305T Oven Installation Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.