Viking DMOC205 Microwave Installation Instructions PDF

1 of 4
1 of 4

Summary of Content for Viking DMOC205 Microwave Installation Instructions PDF

VIKING RANGE CORPORATION 111 Front Street

Greenwood, Mississippi 38930 USA (662) 455-1200

PARTS INCLUDED IN THE KIT

1) Frame Assembly 2) Bottom Duct Assembly QTY 1

3) Screw A (1/2" length) QTY 10

4) Screw B (1-3/4" length) QTY 4

5) Screw C (3/4" length) QTY 2

6) Duct A (1) QTY 1

7) Duct A (2) QTY 1

8) Duct A (3) QTY 1

9) Duct B QTY 1

10) Duct C QTY 1

11) Template: QTY 1

Front Frame QTY 1

Back Frame QTY 1

INSTALLATION INSTRUCTIONS DESIGNER SERIES CONVECTION MICROWAVE BUILT-IN TRIM KIT Retain for Future Reference IMPORTANT - PLEASE READ AND FOLLOW

Beforebeginning,pleasereadtheseinstructionscompletelyandcarefully.

BesuretoDISCONNECTTHEPLUGofthemicrowaveovenfromtheelectricaloutletbeforeinstallingthebuilt-intrimkit. Removetheturntablefromtheovencavity.

Becausethekitincludesmetalparts,cautionshouldbeusedinhandlingandinstallationtoavoidthepossibilityofinjury.

Donotremovepermanentlyaffixedlabels,warnings,orplatesfromtheproduct.Thismayvoidthewarranty.

Pleaseobservealllocalandnationalcodesandordinances.

The installer should leave these instructions with the consumer who should retain for local inspectors use and for future reference.

THIS BUILT-IN TRIM KIT IS DESIGNED FOR USE ONLY WITH VIKING CONVECTION MICROWAVE OVENS SPECIFY- ING BUILT-IN TRIM KIT DMTK276 OR DMTK306 FOR DESIGNER UNITS ON THE RATING LABEL ON THE BOTTOM FACE PLATE OF THE OVEN CAVITY.

IF YOUR LOWER CONVENTIONAL OVEN IS NOT LISTED IN THE USE AND CARE MANUAL OF THE MICROWAVE OVEN, THEN DO NOT INSTALL THE MICROWAVE OVEN ABOVE IT OR IN ANY AREA WHERE HEAT AND STEAM ARE GENERATED; FOR EXAMPLE, NEXT TO OR ABOVE A CONVENTIONAL RANGE.

SCREW A

SCREW A

DUCT A-2

DUCT A-1

DUCT C

#1

DUCT B

SCREW A

SCREW A

18-11/16" (47.5 cm)

24-7/8" (63.3 cm)

5" (12.7 cm)

20-1/8" (51.1 cm)

11-1/2" (29.2 cm)

Illustration 1

Illustration 2

Illustration 3

SCREW A

DUCT A-1

DUCT BC SCREW A

Illustration 4

SCREW A

SCREW A

SCREW A

DUCT A-3

DUCT A-2

Illustration 5

CABINET OR WALL CUTOUT

Provideanopeninginthewallorcabinetasindicatedin illustration1.Thedepthshouldbeaminimumof0-1/8" (51.1cm).Theflooroftheopeningshouldbeconstructed ofplywoodstrongenoughtosupporttheweightofthe oven (about 100 lbs.) and should be level for proper operationoftheoven.

NOTE:Whiletheproperfunctioningoftheovendoesnot requirethattheopeningbeenclosed(withsides,ceiling andrearpartition),thismayberequiredbylocalcode, andit issuggestedthatthe localcodebecheckedfor anysuchrequirement.

ELECTRICAL OUTLET LOCATION

OutletshouldNOTbeintheshadedareaasindicated on illustration1.At the rearof theopening,providea 3-pronged,polarized,electricaloutlet,115-10voltAC, 15amporlarger.

EXHAUST DUCT ASSEMBLY

1.InserttheedgeofDUCT(B)intotheholdlipofDUCT (C).SecuretogetherbyusingaSCREW(A)providedin thekit.Removetheexistingscrew(#1)atupperright rearoftheovenandsecureDUCT(C)withthescrew (#1)justremovedfromtheoven.SecureDUCT(B)with SCREW(A)throughtheductandintotheoriginalscrew holeintheoven.Seeillustration.

.PositionDUCT(A)-1onthetopoftheoveninserting edgeofDUCT (BC)assembly intohole lipofDUCT (A)-1.TightentwoSCREWS(A),securingDUCT(A)-1 toDUCT(BC)assembly.Seeillustration3.

3.PositionDUCT(A)-onthetopoftheovenandinsert itintotheholdlipofDUCT(A)-1.SecureDUCT(A)- toDUCT(A)-1usingtwoSCREWS(A)provided.See illustration4.

4.PositionDUCT(A)-3ontopoftheovenandinsertit intoDUCT(A)-.SecureDUCT(A)-3usingthreescrews (A)provided.Seeillustration5.

Illustration 6

SCREW B

SCREW B

SCREW B

SCREW B

Illustration 9

Illustration 7

Illustration 8

BOTTOM DUCT ASSEMBLY

FOOT

DUCT RECESS

NOTE: CENTER BOTTOM DUCT ASSEMBLY iN ThE OpENiNg

SCREW

BOTTOM DUCT

ASSEMBLY

DETAiL A

SCREW C

gAp "A"

gAp "B"

3

MOUNTING TEMPLATE

1.Alignthemountingtemplatecenterlinewiththecenter of thecutoutandthefloor linewith thefloorof the cutout.Tapeitintoplace.

.ForDMTK76,onlypredrill4holesmarkedAwith a1/16"drill bit. ForDMTK306,onlypredrill 4holes markedBwitha1/16"drillbit.

3.Removetemplatefromthecabinet.

BOTTOM DUCT ASSEMBLY

1.PlacetheBottomductinthecenteroftheopeningso thatgap"A"isequaltogap"B".WhentheBOTTOM DUCT ASSEMBLy is in the opening correctly, the bottomflangewillfittightlyagainsttheloweredgeof theopening.Seeillustration6.

.SecuretheBOTTOMDUCTASSEMBLywiththetwo (3/4")SCREWS(C).IMPORTANT: Securescrewsusing holesonbottomflange.

CABINET INSTALLATION

1.Placetheovenadjacenttothewallorcabinetopening. Plugthepowercordintotheelectricaloutlet.

.Carefullyguidetheassembledovenintotheprepared opening. Slide the oven on the BOTTOM DUCT ASSEMBLy.Seeillustration7.Avoidpinchingthecord betweentheovenandthewall. Adjusttheposition oftheovensothatthefeetoftheovenarefittedinto the holes of the BOTTOM DUCT ASSEMBLy. See illustration8.

FRAME INSTALLATION

Position the BACK FRAME to align with the predrilled holesthatweredrilledwiththemountingtemplate.Check thatitislevelandthensecurewithtwoSCREWS(B).See illustration 9. Secure the bottom portion of the BACK FRAMEwiththetworemainingSCREWS(B).

Illustration 10

SNAP ATTACHMENT 2" (5.1 cm) For 27" W and 30" W lower oven

MICROWAVE CUTOUT

LOWER OVEN CUTOUT

Illustration 11

FRAME INSTALLATION CONT. OVER OVEN INSTALLATION

TABS

Place the FRONT FRAME, with tabs on top, onto the BACK FRAME. Secure the FRONT FRAME to the BACK FRAME by rmly pushing the front frame onto the back frame engaging the four (4) snap attachments. See illustration 10.

Viking Range Corporation 111 Front Street Greenwood, Mississippi (MS) 38930 USA (662) 455-1200

Specications subject to change without notice. For more product information, call 1-888-VIKING1 (845-4641), or visit our web site at http://www.vikingrange.com

F20302A (PS0506VR)

TINSEB467MRR0

BASIC SPECIFICATIONS Microwave Oven Built-In Designer Trim Kits

DMOC205 DMTK276 DMTK306

Overall Width 24-5/8" (62.5 cm) 26-9/16" (67.5 cm) 29-1/2" (74.9 cm)

Overall Height from Bottom 14-7/8" (37.7 cm) 19-13/16" (50.1 cm) 19-13/16" (50.1 cm)

Overall Depth from Rear 19" (48.3 cm) N/A

Oven Interior Width Height Depth Overall

Manualsnet FAQs

If you want to find out how the DMOC205 Viking works, you can view and download the Viking DMOC205 Microwave Installation Instructions on the Manualsnet website.

Yes, we have the Installation Instructions for Viking DMOC205 as well as other Viking manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Installation Instructions should include all the details that are needed to use a Viking DMOC205. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Viking DMOC205 Microwave Installation Instructions is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Viking DMOC205 Microwave Installation Instructions consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Viking DMOC205 Microwave Installation Instructions free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Viking DMOC205 Microwave Installation Instructions, simply download the document to your computer. Once downloaded, open the PDF file and print the Viking DMOC205 Microwave Installation Instructions as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.