Viking DCWL3944 Hood Use and Care Manual PDF

1 of 9
1 of 9

Summary of Content for Viking DCWL3944 Hood Use and Care Manual PDF

F20861 EN (061011)

Viking Use & Care Manual

Designer Hoods

Viking Range Corporation

111 Front Street

Greenwood, Mississippi 38930 USA

(662) 455-1200

For product information

call 1-888-VIKING1 (845-4641),

or visit the Viking Web site at

vikingrange.com

Warnings

3

Congratulations Your purchase of a Viking hood attests to the importance you place upon the quality and performance of the major appliances you use. With minimal care, as outlined in this guide, your new hood is designed to provide you with years of reliable service. Please take a few minutes to learn about its proper and efficient use and care.

This guide will provide you with the information you need to become familiar with your hoods care and operation.

Your complete satisfaction is our ultimate goal. If you have any questions or comments about this product, please contact the dealer from whom you purchased it, or contact our Consumer Support Center at 1-888-VIKING1.

We appreciate your choosing a Viking Range Corporation product, and hope that you will again select our products for your other major appliance needs.

For more information about the complete and growing selection of Viking products, contact your dealer or visit us online at vikingrange.com.

2

WARNING To reduce the risk of fire, electric shock, or injury when using your unit, observe the following:

Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction.

Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent back drafting. Follow the heating equipment manufacturers guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.

When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.

Ducted fans must always be vented to the outdoors. WARNING!: To reduce the risk of fire, use only metal ductwork.

CAUTION!: To reduce risk of fire and to properly exhaust air, be sure to duct air outside. Do not vent exhaust air into spaces within walls or ceilings, or into attics, crawl spaces, or garages.

WARNING To reduce the risk of fire, electric shock, or injury to persons, observe the following:

Use this unit only in the manner for which it is intended. If you have any questions, contact the manufacturer.

Before servicing or cleaning unit, switch power off at service panel and lock service panel to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.

READ AND SAVE THESE INSTRUCTIONS

Warnings (cont.)

4

CAUTION DO NOT place flammable material on warming shelves when using heat lamps.

CAUTION Unplug power cords from control panel before cleaning or servicing hood.

CAUTION All brass special ordered parts are coated with an epoxy coating. DO NOT use brass cleaners or abrasive cleansers on the brass option parts.

Warnings (cont.)

WARNING To reduce the risk of injury to persons in the event of a rangetop grease fire, observe the following: (Based on Kitchen Firesafety Tips, published by NFPA.)

1. SMOTHER FLAMES with a close fitted lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.

2. NEVER PICK UP A FLAMING PAN. You may be burned. 3. DO NOT USE WATER, including wet dishcloths or towels a

violent steam explosion will result. 4. Use an extinguisher ONLY if

You know it is a Class ABC extinguisher, and you already know how to operate it.

The fire is small and contained in the area where it started.

The fire department is being called. You can fight the fire with your back to an exit. CAUTION

Do not use a porcelain cleaner or rough abrasive cleaner.

WARNING TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS, RANGEHOODS MUST BE INSTALLED WITH THE VENTILATORS THAT ARE SPECIFIED ON THEIR CARTON INDICATING SUITABILITY WITH THIS MODEL. OTHER VENTILATORS CANNOT BE SUBSTITUTED.

CAUTION For general ventilating use only. DO NOT use to exhaust hazardous or explosive materials and vapors.

CAUTION If the power to the hood is not disconnected during cleaning, the heat sensor thermostat can cause the blower to turn on.

5

TO REDUCE THE RISK OF A RANGETOP GREASE FIRE: 1. Never leave surface units unattended at high setting. Boilovers

cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings.

2. Always turn hood ON when cooking at high heat or when cooking flaming foods. (i.e. Crepes suzette, Cherries jubilee, Peppercorn beef flamb).

3. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter.

4. Use proper pan size. Always use cookware appropriate for the size of the surface element.

WARNING

7

G etting

Started

Before Using Hood Although the hood is cleaned upon completion of the manufacturing process, you will probably need to clean your hood again after installation. Wipe the surface of the hood with a good household cleaner applied with a soft cloth, or stainless steel polish, depending on the finish of your hood. This will leave a protective finish on the hood.

Heat Sensor Thermostat Your hood is equipped with a heat sensor thermostat. The thermostat will turn on or speed up the blower if it senses excessive heat above the cooking surface. When the sensor activates, the letters HOT will appear on the display. If the blower is OFF - the sensor turns the blower on to HIGH speed. If the blower is on at a lower speed setting - the sensor turns the blower up to HIGH speed. When the temperature level drops to normal, the blower will return to its original setting and the display will be cleared.

Features

CAUTION If the power to the hood is not disconnected during cleaning, the heat sensor thermostat can cause the blower to turn on.

Table of Contents Getting Started Before Using Hood ______________________________________________7

Features _________________________________________________________7

Heat Sensor Thermostat _____________________________________7

Product Controls/Operation Settings and Functions __________________________________________8

Hood Operation _____________________________________________8

DCH/DPPV Model Operation ________________________________9

Product Care Cleaning and Maintenance _____________________________________10

Baffle Filters ________________________________________________10

Mesh Filters ________________________________________________12

Charcoal Filters ___________________________________________________12

Hood Canopy ____________________________________________________13

Enamel Finish _______________________________________________13

Stainless Steel Finish ________________________________________13

Brass Parts __________________________________________________14

Ductless Venting Chamber __________________________________14

Light Bulbs _________________________________________________14

Service Information _____________________________________________15

Warranty _______________________________________________________16

G et ti ng

St ar te d

6

P ro d uct

C o ntro

ls/O p eratio

n

9

Settings and Functions

P ro d uc t C o nt ro ls /O

p er at io n

8

Settings and Functions Hood Operation Always turn on your hood before you begin cooking to establish airflow in the kitchen. Also let the blower run for a few minutes to clear the air after you turn off your cooking appliance. This will help keep the kitchen air cleaner.

Light knobPush once to turn lights on. Push again to turn lights off. Rotate clockwise to increase light intensity and counterclockwise to decrease light intensity. Light setting will stay the same when turned on or off. Fan knobPush once to turn blower on. Push again to turn blower off. Rotate clockwise to increase blower speed and counterclockwise to decrease blower speed. Digital displayRemains blank while timer/delay functions are not in use. Displays desired set time which is set by either the set button or delay function button. Upon reaching 00:00, the buzzer will sound and will continue to beep every 10 seconds up to 5 minutes. Delay feature buttonPushing this button once will automatically set the digital display to 10 minutes. Pushing again will go to 20 minutes and so forth, up to 30 minutes. The blower will activate and the timer will start counting down until 00:00 is reached. At this time the display will go blank and blower will cut off. Scroll up buttonChanges timer display upward to 12 hours. Scroll down buttonChanges timer display downward to 00:00. Set buttonPushing once will activate display (00:00) and allow you to enter time using the scroll up or scroll down buttons. The blower cannot be activated using the set button. Only the timer will be activated. Upon reaching 00:00, the buzzer will sound and will continue to beep every 10 seconds up to 5 minutes.

Light control Digital display Fan control

Light Fan

Timer

Set button Delay feature button

Push On/Off Push On/Off

Set Delay

Scroll down button Scroll up button

00:00

DCH/DPPV Model Operation Always turn on your hood before you begin cooking to establish airflow in the kitchen. Also let the blower run for a few minutes to clear the air after you turn off your cooking appliance. This will help keep the kitchen air cleaner.

ON/OFF switchStarts and stops the blower. When turned on the blower will operate at the previous setting of the speed control. Blower speed knobTurn counterclockwise to decrease the blower speed and clockwise to increase the speed. The type of cooking you are doing will dictate the speed of the blower you use. Light switchControls the 50-watt halogen lights located in the front of the hood. Dimmer knobTurn the knob clockwise to brighten the lights and counterclockwise to dim.

LIGHTS FAN PUSH ON/OFF PUSH ON/OFF

HIGHLOW HIGHLOW

Light switch

ON/OFF switch

Dimmer knob Blower speed knob

10

P ro d uc t C ar e

11

P ro d uct

C are

Any piece of equipment works better and lasts longer when maintained properly and kept clean. Ventilation equipment is no exception. Your hood must be kept clean and maintained properly.

Cleaning Baffle Filters As air passes through a baffle filter, grease particles collect on the stainless steel U-shaped baffle channels and drip down into the bottom of the filter. Baffle filters are extremely efficient when compared to mesh filters. The power of the hood is increased as more air passes through a baffle filter than with mesh filters, which are usually dirty. Baffle filters are almost universally required in commercial installations due to their superior ability to capture grease. The baffle filters should be examined periodically to assure that all surfaces and parts are clean. The filters can be washed in a dishwasher or in a sink with hot, soapy water. Simple periodic cleaning will ensure maximum filter effectiveness.

Do not use caustic detergent to clean the filters. An abrasive or corrosive cleaner may damage the finish.

Do not take the baffle filters apart to clean them. It is not necessary and will void the filter warranty.

CAUTION Unplug power cords from control panel before cleaning or servicing hood.

Cleaning and Maintenance Cleaning and Maintenance

3

2

1 1

3

2

1 2

3

2

1 3

Slide filter forward off of rear lip. Lower filter rear, then slide filter front out.

Slide spacer forward off of rear lip. Lower spacer rear, then slide spacer front out.

Slide filter forward off of rear lip. Lower filter rear, then slide filter front out.

Grease trough (18 H. hoods only)

When cleaning filters in 18H. hoods, always remove the grease trough and clean by soaking in a sink with hot soapy water.

Note: Professional oven shown.

13

P ro d uct

C are

12

P ro d uc t C ar e

Cleaning and Maintenance Cleaning Mesh Filters As air passes through the filter, grease particles collect on the stainless steel screen inside the filter. The filters should be examined periodically to assure that all surfaces and parts are clean. This unit is equipped with an alarm. Once the unit has been in operation for 48 hours, the letters FILT will appear on the display. The filters can then be washed in a dishwasher or in a sink with hot, soapy water. Simple periodic cleaning will ensure maximum effectiveness. Do not use caustic detergent to clean the filters. An abrasive or corrosive cleaner may damage the finish. Do not take the filters apart to clean them. It is not necessary and will void the filter warranty. Once the filters have been cleaned and placed back in the hood, the display is canceled by holding the scroll up (+) and the scroll down (-) buttons for 5 seconds.

Maintaining Charcoal Filter (Recirculating Hoods Only) Replace the charcoal filters every 6 months to 1 year depending on the amount and type of cooking you do.

To replace, remove the baffle/charcoal filter assembly and slide the charcoal filter out of the channel and replace with a new one. Do not put the charcoal filters in the dishwasher.

Replacement filters are available through your local Viking Range dealer, or you can call the Viking Online Store at 1-877-834-8222 or visit vikingrange.com

CAUTION For general ventilating use only. DO NOT use to exhaust hazardous or explosive materials and vapors.

3

2

1 1

3

2

1 2

Slide filter front over front lip. Push filter rear up, then slide back over rear lip.

Slide filter front over front lip. Push filter rear up, then slide back over rear lip.

Cleaning and Maintenance Cleaning Hood Canopy Finishes in enamel or stainless steel are highly resistant to damage or discoloration due to grease, steam, and heat provided that reasonable care is given to the equipment. The following suggestions will help keep your hood looking new.

1. Do not allow an excessive accumulation of grease. For best results, you should wipe your hood clean with a cloth dipped in warm, soapy water. DO NOT USE ABRASIVE CLEANSERS, STEEL WOOL PADS, OR ABRASIVE CLOTHS. DO NOT use cleansers that contain chlorides; the chlorides in the cleaner could damage the stainless steel finish. If you need to scrape stainless steel to remove encrusted materials, first soak the area with hot towels to loosen the material, then use a wooden or nylon spatula or scraper. DO NOT use a metal knife, spatula, or any other metal tool to scrape stainless steel.

2. Every 3 months give your hood a thorough cleaning. On painted surfaces, use a new coat of wax. A good wax cleaneravailable at either a grocery or hardware storewill do both jobs at once. On stainless steel surfaces, use a good stainless steel cleaner and polish.

Renewing Enamel Finish If discoloration occurs, you should thoroughly polish the finish on your hood to renew its gloss and luster and to remove any grease residue which may have a yellowing effect. Use any good enamel polish, refrigerator polish, or automotive polish.

Renewing Stainless Steel Finish Regular cleaning is the best way to assure that your stainless steel finish stays bright and unscratched. Use lemon oil or stainless steel polish to coat and protect stainless steel.

CAUTION All brass special ordered parts are coated with an epoxy coating. DO NOT use brass cleaners or abrasive cleansers on the brass option parts.

CAUTION Do not use a porcelain cleaner or rough abrasive cleaner.

15

P ro d uct

C are

14

P ro d uc t C ar e

Cleaning Brass Parts All brass body parts should be wiped regularly with hot soapy water. When hot soapy water will not do the job, use every day household cleaners that are not abrasive.

Replacing the Light Bulbs When removing bulbs use an oven mitt to protect your hand in case the bulb breaks.

Halogen Lights 1. Unscrew halogen bulb. 2. Replace the bulb with a 120 volt, 50-watt halogen bulb.

Infrared Heat Lamp 1. Unscrew infrared bulb from heat lamp socket. 2. Replace the bulb with an R40, 120 volt, 250-watt infrared

bulb.

Cleaning and Maintenance

1

2

1

1 1

2

2

Service Information

If service is required, call your dealer or authorized service agency. The name of the authorized service agency can be obtained from the dealer or distributor in your area.

Have the following information readily available. Model number Serial number Date purchased Name of dealer from whom purchased

Clearly describe the problem that you are having. If you are unable to obtain the name of an authorized service agency, or if you continue to have service problems, contact Viking Range Corporation at 1-888-VIKING1 (845-4641), or write to:

VIKING RANGE CORPORATION PREFERRED SERVICE

1803 Hwy 82W Greenwood, Mississippi 38930 USA

Record the information indicated below. You will need it if service is ever required. The model and serial number for your hood is located behind the baffle filter on the left side panel in the lower right corner.

Model no._____________________ Serial no. ________________________

Date of purchase _______________ Date installed ___________________

Dealers name __________________________________________________

Address ________________________________________________________

_______________________________________________________________

If service requires installation of parts, use only authorized parts to ensure protection under the warranty.

THIS MANUAL SHOULD REMAIN WITH THE HOOD FOR FUTURE REFERENCE.

P ro d uc t C ar e

1716

HOODS WARRANTY THREE YEAR FULL WARRANTY

Hoods and all of their component parts, except as detailed below*, are warranted to be free from defective materials or workmanship in normal residential use for a period of three (3) year from the date of original retail purchase or closing date for new construction, whichever period is longer. Viking Range Corporation, warrantor, agrees to repair or replace, at its option, any part which fails or is found to be defective during the warranty period.

*FULL NINETY (90) DAY COSMETIC WARRANTY: Product is warranted to be free from cosmetic defects in materials or workmanship (such as scratches on stainless steel, paint/porcelain blemishes, etc.) for a period of ninety (90) days from the date of original retail purchase or closing date for new construction, whichever period is longer. Any defects must be reported to the selling dealer within ninety (90) days from date of original retail purchase. Viking Range Corporation uses high quality processes and materials available to produce all color finishes. However, slight color variation may be noticed because of the inherent differences in painted parts and porcelain parts as well as differences in kitchen lighting, product locations, and other factors. Therefore, this warranty does not apply to color variation attributable to such factors.

FULL NINETY (90) DAY WARRANTY IN "RESIDENTIAL PLUS" APPLICATIONS: This full warranty applies to applications where use of the product extends beyond normal residential use, but the warranty period for products used in such applications is ninety (90) days. Examples of applications covered by this warranty are bed and breakfasts, fire stations, private clubs, churches, yachts, etc. Under this "Residential Plus" warranty, the product, its components and accessories are warranted to be free from defective material or workmanship for a period of ninety (90) days from the date of original retail purchase. This warranty excludes use of the product in all commercial locations such as restaurants, food service locations and institutional food service locations.

FIVE YEAR LIMITED WARRANTY ON VENTILATION MOTORS Any ventilator motor which fails due to defective materials or workmanship in normal household use during the fourth year through the fifth year from the date of original retail purchase will be repaired or replaced, free of charge for the part itself, with the owner paying all other costs, including labor.

LIMITED WARRANTY ON STAINLESS STEEL (T-Series Models Only) Any stainless steel part which rusts through due to defective materials or workmanship in normal use during the fourth year through the useful lifetime of the unit from date of original retail purchase will be repaired or replaced free of charge for the part itself, with the owner paying all other costs including labor.

TERMS AND CONDITIONS This warranty extends to the original purchaser of the product warranted hereunder and to each transferee owner of the product during the term of the warranty and applies to products purchased and located in the United States and Canada. Products must be purchased in the country where service is requested. If the product or one of its component parts contains a defect or malfunction during the full warranty period after a reasonable number of attempts by the warrantor to remedy the defect or malfunction, the owner is entitled to either a refund or replacement of the product or its component part or parts. Replacement of a component part includes its free installation, except as specified under the limited warranty. Under the terms of this warranty, service must be performed by a factory authorized Viking Range Corporation service agent or representative. Service will be provided during normal business hours, and labor performed at overtime or premium rates shall not be covered by this warranty.

Owner shall be responsible for proper installation, providing reasonable and necessary maintenance, providing proof of purchase upon request, and making the appliance reasonably accessible for service. The return of the Owner Registration Card is not a condition of warranty coverage. You should, however, return the Owner Registration Card so that Viking Range Corporation can contact you should any question of safety arise which could affect you.

This warranty gives you specific legal rights, and you may also have other rights which may vary from jurisdiction to jurisdiction.

WHAT IS NOT COVERED BY THIS WARRANTY: This warranty shall not apply to damage resulting from abuse, failure to provide reasonable and necessary maintenance, accident, delivery, negligence, natural disaster, loss of electrical power to the product for any reason, alteration, outdoor use, improper installation, improper operation, or repair or service of the product by anyone other than an authorized Viking Range Corporation service agency or representative. This warranty does not apply to commercial usage.

Warranty Warranty (cont.)

LIMITATION OF REMEDIES AND DURATION OF IMPLIED WARRANTY OWNERS SOLE AND EXCLUSIVE REMEDY FOR A CLAIM OF ANY KIND WITH RESPECT TO THIS PRODUCT SHALL BE THE REMEDIES SET FORTH ABOVE.VIKING IS NOT RESPONSIBLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGE, INCLUDING BUT NOT LIMITED TO FOOD OR MEDICINE LOSS, DUE TO PRODUCT FAILURE, WHETHER ARISING OUT OF BREACH OF WARRANTY, BREACH OF CONTRACT OR OTHERWISE. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusions may not apply to you. ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE APPLICABLE TO THIS PRODUCT ARE LIMITED IN DURATION TO THE PERIOD OF COVERAGE OF THE APPLICABLE EXPRESS WRITTEN LIMITED WARRANTIES SET FORTH ABOVE. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.

WARRANTY SERVICE To obtain warranty service, contact an authorized Viking Range Corporation service agent, or Viking Range Corporation, 111 Front Street, Greenwood, Mississippi 38930, (888) 845-4641. Provide model and serial number and date of original purchase or

Manualsnet FAQs

If you want to find out how the DCWL3944 Viking works, you can view and download the Viking DCWL3944 Hood Use and Care Manual on the Manualsnet website.

Yes, we have the Use and Care Manual for Viking DCWL3944 as well as other Viking manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Use and Care Manual should include all the details that are needed to use a Viking DCWL3944. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Viking DCWL3944 Hood Use and Care Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Viking DCWL3944 Hood Use and Care Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Viking DCWL3944 Hood Use and Care Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Viking DCWL3944 Hood Use and Care Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Viking DCWL3944 Hood Use and Care Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.