Viking RLPKR2 Gas Use and Care Manual PDF

1 of 8
1 of 8

Summary of Content for Viking RLPKR2 Gas Use and Care Manual PDF

1-EN

The pressure regulator and the burner orifices are set for Natural gas. To use Liquid Propane gas, the regulator and burner orifices must be converted.

To convert the range to LP gas, follow these instructions: 1. Disconnect all electrical power at the main circuit breaker or

fuse box. 2. Shut off the gas supply to the range by closing the manual

shut-off valve.

Converting the Pressure Regulator 1. Locate the pressure regulator which can be found on the back

of the range on the right hand side if facing the back of the range.

2. Unscrew the hex nut cap from the top of the regulator. 3. Unsnap the plastic plunger from the hex nut. 4. Reverse the plunger and reinstall onto the hex nut by

pressing firmly.

Note: Plunger is marked Nat and LP. Converted fuel type will be shown on the lower portion of the plunger.

Converting the Surface Burners 1. Remove the top grates, burner caps, and burner heads.

2. Using a 9/32 or 7 mm nut driver remove the top burner orifices. These may be accessed through the opening in the burner base.

Note: Save these orifices for future conversion back to Natural gas, if required.

3. Locate the proper LP surface burner orifices included with the kit according to the chart below. The orifice stamp can be either the metric diameter size or the orfice drill size.

4. Install the orifices in their correct location. To prevent leakage, make sure the orifice spuds are securely screwed into the burner base.

W A R N I N G The conversion must be performed by a qualified

installer or gas supplier in accordance with the

manufacturers instructions and all codes and

requirements of the authority having jurisdiction. Failure to

follow ALL instructions could result in serious injury or

property damage. The qualified agency performing this

work assumes responsibility for this conversion.

NAT

LP

N AT

LP

Apply sideways finger pressure to remove pin from cap.

N AT LP

conversion

conversion

Orifice spud

Burner cap

Burner grate

Burner head

Burner base

Orifice stamp

0.79

Orifice

RLPKR2 LP Conversion Kit Instructions for RVGR3302/RVDR3302 Ranges

Part Number Burner BTU Rate Diameter mm

Orifice Stamp

057741-901 Left front (A) 16,000 1.19 119

057741-902 Left rear (B) 6,500 0.71 71

057741-903 Center (C) 8,000 0.85 85

057741-905 Right rear (D) 11,000 0.95 95

057741-904 Right front (E) 15,000 1.15 115

035282-000 Bake 30,000 1.68 1.68

035283-000 Broil 14,500 1.03 1.03

B

A E

C D

2-EN

Converting the Bake Burner 1. Remove oven racks and oven support. 2. Remove oven bottom. 3. Remove screws securing bake igniter to bake burner. 4. Remove screws securing bake burner shield to oven burner box. 5. Remove screws securing bake burner to oven burner box. 6. Loosen air shutter screw and adjust opening on burner to 3/8

and tighten air shutter screw. 7. Remove orifice by turning counterclockwise and replace with

orifice 1.68 from bag labeled.

Important: The orifice tip must be located 3/16 inside the burner for proper gas mixture and combustion. The depth of the orifice can be adjusted by turning the orifice counterclockwise (more depth) or clockwise (less depth). Reverse procedure as needed to reassemble.

Converting the Broil Burner 1. Remove the screws (4) from the broiler baffle. 2. Carefully remove the broiler burner Note: Pay close attention to the igniter wire while removing the broiler burner.

3. Disconnect the igniter wire. 4. Use a 1/2 wrench to remove the broiler burner natural gas

orifice hood and replace with LP broiler burner hood 1.03. 5. Reinstall the converted broiler burner by first firmly attaching

the igniter wire. 6. Reposition the broiler burner in its original position. 7. Replace the four screws into the broiler baffle.

Air Shutter Settings for Broiler Burner 1. Use a screwdriver to loosen the air shutter screw. 2. Adjust the air shutters for LP gas by rotating the shutter to the

fully open position. Your final settings may vary. 3. Retighten the air shutter screw. Bake and broiler flame must be checked with the door closed to

properly check flame characteristics.

4. Turn on the gas. 5. Turn on the electricity.

6. Retighten the air shutter screw. 7. Turn on the bake and broiler burner. 8. As you watch the flame with the oven door closed, check the

following through the oven door window: a. If the flames are yellow, open the air shutter more. b. If the flames blow away or flutter from the burner, close

the air shutter more. 9. Open the oven door and check the inner cone of the bake

and broiler burner flame. It should be approximately 1/2 to 3/4 long for the bake and broil burners. The combustion quality of the burner flames needs to be determined visually. With LP gas, some yellow tipping on the outer cones is normal.

10. When all adjustments are made and the results are satisfactory then replace the oven bottom cover.

In some cases, foreign particles in the gas line may cause an orange flame at first but this will soon disappear.

Note: To convert the oven back to Natural gas, reverse the instructions given for making the LP gas adjustments.

Note: When the LP/Propane conversion is finished, complete the enclosed conversion label and place it next to the rating label.

Vo let d 'ai

A ir Sh u t te r

A ir Sh u t te r Se t Scre w

O r ifice H o o d

Ad justment Screw

Air Shutter

Adjustment screwAir shutter

W A R N I N G If you attempt to measure the inner cone of the

flame, please use caution as burns could result.

3-EN

The pressure regulator and the burner orifices are set for LP gas. To use natural gas, the regulator and burner orifices must be converted.

To convert the range to NAT gas, follow these instructions: 1. Disconnect all electrical power at the main circuit breaker or

fuse box. 2. Shut off the gas supply to the range by closing the manual

shut-off valve.

Converting the Pressure Regulator 1. Locate the pressure regulator which can be found on the back

of the range on the right hand side if facing the back of the range.

2. Unscrew the hex nut cap from the top of the regulator. 3. Unsnap the plastic plunger from the hex nut. 4. Reverse the plunger and reinstall onto the hex nut by

pressing firmly.

Note: Plunger is marked Nat and LP. Converted fuel type will be shown on the lower portion of the plunger.

Converting the Surface Burners 1. Remove the top grates, burner caps, and burner heads.

2. Using a 9/32 or 7 mm nut driver remove the top burner orifices. These may be accessed through the opening in the burner base.

Note: Save these orifices for future conversion back to NAT gas, if required.

3. Locate the proper NAT surface burner orifices included with the kit according to the diagram below. The orifice stamp can be either the metric diameter size or the orfice drill size.

4. Install the orifices in their correct location. To prevent leakage, make sure the orifice spuds are securely screwed into the burner base.

W A R N I N G The conversion must be performed by a qualified

installer or gas supplier in accordance with the

manufacturers instructions and all codes and

requirements of the authority having jurisdiction. Failure to

follow ALL instructions could result in serious injury or

property damage. The qualified agency performing this

work assumes responsibility for this conversion.

NAT

LP

N AT

LP

Apply sideways finger pressure to remove pin from cap.

N AT LP

conversion

conversion

Orifice spud

Burner cap

Burner grate

Burner head

Burner base

Orifice stamp

0.79

Orifice

RNKR2 NAT Conversion Kit Instructions for RVGR3302/RVDR3302 Ranges

B

A E

C D

Part Number Burner BTU Rate Diameter mm

Orifice Stamp

057747-901 Left front (A) 18,000 2.00 200

057747-902 Left rear (B) 9,100 1.38 138

057747-903 Center (C) 9,100 1.38 138

057747-905 Right rear (D) 12,000 1.58 158

057747-904 Right front (E) 17,000 1.88 189

015695-000 Bake 30,000 2.58 #38

PB040034 Broil 15,000 1.87 #50

Converting the Bake Burner 1. Remove oven racks and oven support. 2. Remove oven bottom. 3. Remove screws securing bake igniter to bake burner. 4. Remove screws securing bake burner shield to oven burner box. 5. Remove screws securing bake burner to oven burner box. 6. Loosen air shutter screw and adjust opening on burner to 3/8

and tighten air shutter screw. 7. Remove orifice by turning counterclockwise and replace with

orifice from bag labeled 2.58 (#38) .

Important: The orifice tip must be located 3/16 inside the burner for proper gas mixture and combustion. The depth of the orifice can be adjusted by turning the orifice counterclockwise (more depth) or clockwise (less depth). Reverse procedure as needed to reassemble.

Converting the Broil Burner 1. Remove the screws (4) from the broiler baffle. 2. Carefully remove the broiler burner Note: Pay close attention to the igniter wire while removing the broiler burner.

3. Disconnect the igniter wire. 4. Use a 1/2 wrench to remove the broiler burner LP gas orifice

hood and replace with NAT broiler burner hood 1.87 (#50). 5. Reinstall the converted broiler burner by first firmly attaching

the igniter wire.

6. Reposition the broiler burner in its original position. 7. Replace the four screws into the broiler baffle.

Air Shutter Settings for Broiler Burner 1. Use a screwdriver to loosen the air shutter screw. 2. Adjust the air shutters for NAT gas by rotating the shutter to

the fully open position. Your final settings may vary. 3. Retighten the air shutter screw. Bake and broiler flame must be checked with the door closed to properly check flame characteristics.

4. Turn on the gas. 5. Turn on the electricity.

6. Retighten the air shutter screw. 7. Turn on the bake and broiler burner. 8. As you watch the flame with the oven door closed, check the

following through the oven door window: a. If the flames are yellow, open the air shutter more. b. If the flames blow away or flutter from the burner, close

the air shutter more. 9. Open the oven door and check the inner cone of the bake

and broiler burner flame. It should be approximately 1/2 to 3/4 long for the bake and broil burners. The combustion quality of the burner flames needs to be determined visually.

10. When all adjustments are made and the results are satisfactory then replace the oven bottom cover.

In some cases, foreign particles in the gas line may cause an orange flame at first but this will soon disappear.

Note: To convert the oven back to LP gas, reverse the instructions given for making the NAT gas adjustments.

Note: When the NAT conversion is finished, complete the enclosed conversion label and place it next to the rating label.

Vo let d 'ai

A ir Sh u t te r

A ir Sh u t te r Se t Scre w

O r ifice H o o d

Ad justment Screw

Air Shutter

Adjustment screwAir shutter

W A R N I N G If you attempt to measure the inner cone of the

flame, please use caution as burns could result.

057756-000 EN (093015) VIKING RANGE, LLC

111 Front Street Greenwood, Mississippi 38930 USA (662) 455-1200

1-FR

Les orifices du dtendeur et du brleur sont rgls pour le gaz naturel. Pour utiliser du gaz propane liquide, les orifices du dtendeur et du brleur doivent tre convertis.

Pour convertir la cuisinire au gaz PL, suivez ces instructions : 1. Dbranchez toute lalimentation lectrique au disjoncteur

gnral ou la bote fusibles. 2. Coupez larrive de gaz en fermant le robinet darrt manuel.

Conversion du dtendeur 1. Localisez le dtendeur qui se trouve larrire de la

cuisinire, sur le ct droit quand vous regardez larrire de la cuisinire.

2. Dvissez lcrou borgne six pans du dessus du dtendeur. 3. Dtachez le piston plongeur en plastique de lcrou. 4. Retournez le piston plongeur et rinstallez-le sur lcrou en

pressant fermement.

Remarque : Le piston plongeur est marqu Nat et LP . Le type de combustible converti apparatra sur la partie infrieure du piston plongeur.

Conversion des brleurs de surface 1. Enlevez les grilles suprieures, les chapeaux de brleur et les ttes de

brleur.

2. laide dun tourne-crou de 9/32 po ou 7 mm, enlevez les orifices suprieurs du brleur. Vous pouvez y accder par louverture dans la base du brleur.

Remarque : Mettez ces orifices de ct pour une reconversion future au gaz naturel.

3. Localisez les orifices de brleur PL corrects inclus avec lensemble, conformment la liste ci-dessus. Le timbre de l'orifice peut tre diamtre mtrique perceuse ou la taille de foret.

4. Installez les orifices au bon endroit. Pour viter les fuites, assurez-vous que lembase des orifices est solidement visse sur la base du brleur.

AVERTISSEMENT La conversion doit tre confie un installateur

qualifi ou un fournisseur de gaz conformment

aux instructions du fabricant et tous les codes et

exigences de lautorit ayant juridiction. Le non-respect de

TOUTES les instructions peut causer des blessures graves

ou des dgts matriels. Lagence qualifie ralisant le

travail endosse la responsabilit de cette conversion.

LP

NAT

LP

NAT

LP

Appuyez sur le ct avec le doigt pour enlever la goupille du chapeau

Gaz naturel

NAT

LP

Conversion

Conversion

Embase d'orifice

Chapeau de brleur

Grille de brleur

Tte de brleur

Base de brleur

0.79

Orifice

Timbre de l'orific

RLPKR2 Instructions de lensemble de conversion au PL pour les cuisinires CRVGR3302/CRVDR3302

B

A E

C D

Numro de picer

Brleur BTU Diamtre mm

Timbre de lorifice

057741-901 Avant gauche (A) 16,000 1.19 119

057741-902 Arrire gauche (B) 6,500 0.71 71

057741-903 Centre (C) 8,000 0.85 85

057741-905 Arrire droit (D) 11,000 0.95 95

057741-904 Avant droit (E) 15,000 1.15 115

035282-000 Bake (cuisson au four) 30,000 1.68 1.68

035283-000 Broil (cuisson au gril) 14,500 1.03 1.03

2-FR

Conversion du brleur de cuisson au four 1. Enlevez les grilles du four et leur support. 2. Enlevez le fond du four. 3. Enlevez les vis qui fixent lallumeur du four au brleur du four. 4. Enlevez les vis qui fixent la protection du brleur du four au

botier du brleur de four. 5. Enlevez les vis qui fixent le brleur du four au botier du brleur

de four. 6. Desserrez la vis du registre et ajustez louverture du brleur

3/8, puis resserrez la vis. 7. Enlevez lorifice en tournant dans le sens anti-horaire et

remplacez-le par lorifice du sachet tiquet 1,68.

Important : Pour un mlange et une combustion des gaz corrects, lextrmit de lorifice doit se situer 5 mm lintrieur du brleur. La profondeur de lorifice peut tre ajuste en tournant lorifice dans le sens anti-horaire (plus profond) ou dans le sens horaire (moins profond).

Inversez la procdure au besoin pour remonter.

Conversion du brleur du gril 1. Retirez les vis (4) du dflecteur du gril. 2. Retirez soigneusement le brleur du gril. Remarque : Prtez une attention particulire au cble de lallumeur en enlevant le brleur du gril.

3. Dbranchez le cble de lallumeur. 4. Utilisez une cl de 1/2 po (12 mm) pour enlever le capot de

lorifice gaz naturel du brleur et remplacez-le par le capot de brleur de gril PL 1,03.

5. Remontez le brleur de gril converti en attachant fermement le cble de lallumeur dans un premier temps.

6. Remettez le brleur du gril sa position initiale.

7. Remettez les quatre vis dans le dflecteur du gril.

Rglages du volet dair pour le brleur du gril 1. Utilisez un tournevis pour desserrer la vis du volet dair. 2. Ajustez les volets dair pour gaz PL en tournant le volet en

position grand ouverte. Vos rglages finals pourront varier. 3. Resserrez la vis du volet dair. La flamme de cuisson au four ou du brleur doit tre vrifie la porte ferme pour contrler correctement les caractristiques de la flamme.

4. Ouvrez le gaz. 5. Allumez llectricit. 6. Resserrez la vis du volet dair. 7. Allumez le brleur de cuisson au four ou du gril. 8. En observant la flamme la porte du four ferme, vrifiez ce qui

suit travers la fentre de la porte du four : a. Si les flammes sont jaunes, ouvrez davantage le volet dair. b. Si les flammes se soulvent ou vacillent partir du brleur,

fermez davantage le volet dair. 9. Ouvrez la porte du four et vrifiez le cne interne de la flamme

du brleur de cuisson au four ou du gril. Il doit mesurer entre 1/2 et 3/4 po (12 et 19 mm) de hauteur. La qualit de combustion des flammes de brleur doit tre dtermine visuellement. Avec le gaz PL, la prsence de pointes jaunes sur le cne externe est normale.

10.Une fois tous les rglages effectus et les rsultats satisfaisants, remettez le capot infrieur du four.

Dans certains cas, des particules trangres dans la conduite de gaz peuvent causer une flamme orange au dpart, laquelle disparatra peu aprs.

Remarque : Pour effectuer la reconversion au gaz naturel, procdez inversement.

Remarque : Une fois la conversion LP/Propane termine, remplissez ltiquette de conversion et placez-la ct de ltiquette des valeurs nominales.

'a

Volet d'air

Vis du volet d'air

Couvercle de l'orifice

Volet d'air Vis de rglage

Vis de rglageVolet d'air

AVERTISSEMENT Si vous essayez de mesurer le cne interne de

la flamme, usez de prudence, car vous risquez

de vous brler.

3-FR

Les orifices du dtendeur et du brleur sont rgls pour le gaz naturel. Pour utiliser du gaz propane liquide, les orifices du dtendeur et du brleur doivent tre convertis.

Pour convertir la cuisinire au gaz Naturel, suivez ces instructions : 1. Dbranchez toute lalimentation lectrique au disjoncteur

gnral ou la bote fusibles. 2. Coupez larrive de gaz en fermant le robinet darrt manuel.

Conversion du dtendeur 1. Localisez le dtendeur qui se trouve larrire de la

cuisinire, sur le ct droit quand vous regardez larrire de la cuisinire.

2. Dvissez lcrou borgne six pans du dessus du dtendeur. 3. Dtachez le piston plongeur en plastique de lcrou. 4. Retournez le piston plongeur et rinstallez-le sur lcrou en

pressant fermement.

Remarque : Le piston plongeur est marqu Nat et LP . Le type de combustible converti apparatra sur la partie infrieure du piston plongeur.

Conversion des brleurs de surface 1. Enlevez les grilles suprieures, les chapeaux de brleur et les ttes

de brleur.

2. laide dun tourne-crou de 9/32 po ou 7 mm, enlevez les orifices suprieurs du brleur. Vous pouvez y accder par louverture dans la base du brleur.

Remarque : Mettez ces orifices de ct pour une reconversion future au gaz naturel.

3. Localisez les orifices de brleur Naturel corrects inclus avec lensemble, conformment la liste ci-dessus. Le timbre de l'orifice peut tre diamtre mtrique perceuse ou la taille de foret.

4. Installez les orifices au bon endroit. Pour viter les fuites, assurez- vous que lembase des orifices est solidement visse sur la base du brleur.

AVERTISSEMENT La conversion doit tre confie un installateur

qualifi ou un fournisseur de gaz conformment

aux instructions du fabricant et tous les codes et

exigences de lautorit ayant juridiction. Le non-respect de

TOUTES les instructions peut causer des blessures graves

ou des dgts matriels. Lagence qualifie ralisant le

travail endosse la responsabilit de cette conversion.

LP

NAT

LP

NAT

LP

Appuyez sur le ct avec le doigt pour enlever la goupille du chapeau

Gaz naturel

NAT

LP

Conversion

Conversion

Embase d'orifice

Chapeau de brleur

Grille de brleur

Tte de brleur

Base de brleur

0.79

Orifice

Timbre de l'orific

RNKR2 Instructions de lensemble de conversion au Naturel pour les cuisinires CRVGR3302/CRVDR3302

B

A E

C D

Numro de picer

Brleur BTU Diamtre mm

Timbre de lorifice

057747-901 Avant gauche (A) 18,000 2.00 200

057747-902 Arrire gauche (B) 9,100 1.38 138

057747-903 Centre (C) 9,100 1.38 138

057747-905 Arrire droit (D) 12,000 1.58 158

057747-904 Avant droit (E) 17,000 1.88 189

015695-000 Bake (cuisson au four) 30,000 2.58 #38

PB040034 Broil (cuisson au gril) 15,000 1.87 #50

Conversion du brleur de cuisson au four 1. Enlevez les grilles du four et leur support. 2. Enlevez le fond du four. 3. Enlevez les vis qui fixent lallumeur du four au brleur du four. 4. Enlevez les vis qui fixent la protection du brleur du four au

botier du brleur de four. 5. Enlevez les vis qui fixent le brleur du four au botier du brleur

de four. 6. Desserrez la vis du registre et ajustez louverture du brleur

3/8, puis resserrez la vis. 7. Enlevez lorifice en tournant dans le sens anti-horaire et

remplacez-le par lorifice du sachet tiquet #38 (2,58).

Important : Pour un mlange et une combustion des gaz corrects, lextrmit de lorifice doit se situer 5 mm lintrieur du brleur. La profondeur de lorifice peut tre ajuste en tournant lorifice dans le sens anti-horaire (plus profond) ou dans le sens horaire (moins profond). Inversez la procdure au besoin pour remonter.

Conversion du brleur du gril 1. Retirez les vis (4) du dflecteur du gril. 2. Retirez soigneusement le brleur du gril. Remarque : Prtez une attention particulire au cble de lallumeur en enlevant le brleur du gril.

3. Dbranchez le cble de lallumeur. 4. Utilisez une cl de 1/2 po (12 mm) pour enlever le capot de

lorifice gaz PL du brleur et remplacez-le par le capot de brleur de gril Naturel #50 (1,87).

5. Remontez le brleur de gril converti en attachant fermement le cble de lallumeur dans un premier temps.

6. Remettez le brleur du gril sa position initiale. 7. Remettez les quatre vis dans le dflecteur du gril.

Rglages du volet dair pour le brleur du gril 1. Utilisez un tournevis pour desserrer la vis du volet dair. 2. Ajustez les volets dair pour gaz Naturel en tournant le volet en

position grand ouverte. Vos rglages finals pourront varier. 3. Resserrez la vis du volet dair. La flamme de cuisson au four ou du brleur doit tre vrifie la porte ferme pour contrler correctement les caractristiques de la flamme.

4. Ouvrez le gaz. 5. Allumez llectricit. 6. Resserrez la vis du volet dair. 7. Allumez le brleur de cuisson au four ou du gril. 8. En observant la flamme la porte du four ferme, vrifiez ce qui

suit travers la fentre de la porte du four : a. Si les flammes sont jaunes, ouvrez davantage le volet dair. b. Si les flammes se soulvent ou vacillent partir du brleur,

fermez davantage le volet dair. 9. Ouvrez la porte du four et vrifiez le cne interne de la flamme

du brleur de cuisson au four ou du gril. Il doit mesurer entre 1/2 et 3/4 po (12 et 19 mm) de hauteur. La qualit de combustion des flammes de brleur doit tre dtermine visuellement. Avec le gaz Naturel, la prsence de pointes jaunes sur le cne externe est normale.

10.Une fois tous les rglages effectus et les rsultats satisfaisants, remettez le capot infrieur du four.

Dans certains cas, des particules trangres dans la conduite de gaz peuvent causer une flamme orange au dpart, laquelle disparatra peu aprs.

Remarque : Pour effectuer la reconversion au gaz PL, procdez inversement. Remarque : Une fois la conversion LP/Propane termine, remplissez ltiquette de conversion et placez-la ct de ltiquette des valeurs nominales.

'a

Volet d'air

Vis du volet d'air

Couvercle de l'orifice

Volet d'air

Manualsnet FAQs

If you want to find out how the RLPKR2 Viking works, you can view and download the Viking RLPKR2 Gas Use and Care Manual on the Manualsnet website.

Yes, we have the Use and Care Manual for Viking RLPKR2 as well as other Viking manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Use and Care Manual should include all the details that are needed to use a Viking RLPKR2. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Viking RLPKR2 Gas Use and Care Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Viking RLPKR2 Gas Use and Care Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Viking RLPKR2 Gas Use and Care Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Viking RLPKR2 Gas Use and Care Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Viking RLPKR2 Gas Use and Care Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.