Viking RDEWD103 Drawer Installation Guide PDF
Summary of Content for Viking RDEWD103 Drawer Installation Guide PDF
F20956 EN (032912)
Built-In Electric Warming Drawer
Installation
Viking Range Corporation 111 Front Street
Greenwood, Mississippi 38930 USA (662) 455-1200
For product information, call 1-888-VIKING1 (845-4641) or visit the Viking Website at vikingrange.com
Table of Contents
Warnings & Important Safety Instructions _______________________________________________3 Dimensions _________________________________________________________________________4 Specifications _______________________________________________________________________5 Cutout Dimensions __________________________________________________________________6 Electrical Requirements ______________________________________________________________7 General Information__________________________________________________________________8 Installation __________________________________________________________________________9 Final Preparation ___________________________________________________________________11 Performance Checklist ______________________________________________________________11 Service & Registration_______________________________________________________________12
IMPORTANT Read and Follow!
Your safety and the safety of others is very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.
This is the safety alert symbol. This symbol alerts you to hazards that can kill or hurt you and others.
All safety messages will be preceded by the safety alert symbol and the word DANGER, WARNING or CAUTION. These words mean:
Hazards or unsafe practices which WILL result in severe personal
injury or death
DANGER
Hazards or unsafe practices which COULD result in severe personal
injury or death
Hazards or unsafe practices which COULD result in minor personal injury or
property damage.
All safety messages will identify the hazard, tell you how to reduce the chance of injury, and tell you what can happen if
the instructions are not followed.
WARNING
CAUTION
Before beginning, please read these instructions completely and carefully.
DO NOT remove permanently affixed labels, warnings, or plates from product. This may void the warranty.
All local and national codes and ordinances must be observed. Installation must conform with local codes, or in the absence of codes, the National Electrical Code, ANSI/NFPA70 - latest edition.
The installer must leave these instructions with the consumer who should retain for local inspectors use and for future reference.
In Canada: Installation must be in accordance with the current CSA C22.1 Canadian Electrical Codes Part 1 and/or local codes.
WARNING FIRE AND ELECTRICAL SHOCK HAZARD To reduce the risk of electric shock and fire, DO NOT use a flexible power-supply cord with this appliance.
WARNING For outdoor installation, installer must install a ground fault interrupt.
WARNING Make sure that incoming voltage is the same as unit rating. An electric rating plate specifying voltage, hertz, wattage, amps, and phase is attached to the product. Wiring the warming drawer with more voltage than it is rated for may cause severe damage to the thermostat, element, and other components. Wiring the warming drawer with less voltage than it is rated for may cause significant decrease in performance.
WARNING To reduce the risk of fire, electric shock, or injury to persons, installation work and electrical wiring must be done by qualified people in accordance with all applicable codes and standards, including fire-rated conditions.
2 3
4
Dimensions - RDEWD
5
23-1/4
(59.1 cm)
27-7/16
(69.7 cm)
8-31/32 (22.4 cm)
10(25.4 cm)
29-1/2 (74.9 cm)
27-7/16 (69.7 cm)
23-7/16 (59.5 cm)
1-5/8 (4.1 cm)22-15/16
(58.3 cm)
RDEWD103
Specifications Description RDEWD103
Overall width 29-1/2 (74.9 cm)
Overall height (from bottom) 10-1/4 (26.0 cm)
Overall depth (from rear) To end of handle
With drawer fully extended
27-7/16 (69.7 cm)
48 (121.9 cm)
Interior width 20-1/2 (52.1 cm)
Interior height 10-1/4 (26.0 cm)
Interior depth 22-3/4 (27.8 cm)
Electrical Requirements
Hard wire direct with separate 15 amp minimum 2-wire with ground circuit; 120 VAC/50-60 Hz
Max. Amp Usage 450 watts 3.8 amps
Approx. shipping wt. 90 lb. (40.5 kg)
Rear View RDEWD103
2 (5.1 cm)
8-31/32 (22.8 cm)
27-7/8 (70.8 cm)
2 (5.1 cm)
120V Electrical Opening
(When facing cabinet, opening is located on right side.)
Dimensions
76
Cutout Dimensions - RDEWD
A
C
B
RDEWD103
Cutout width (A) 28-1/4 (71.8 cm) Cutout depth (B) 23-1/2 (59.7 cm)
Cutout height (C) 9-1/4 (23.5 cm)
Indoor
Flush Mount Option: Note: To install the warming drawer in a flush mount application, a flush mount accessory kit is required and sold separately.
RDEWD103
Cutout width (A) 29-5/8 (75.3 cm) Cutout depth (B) 25-1/8 (63.8 cm)
Cutout height (C) 10-1/8 (25.7 cm)
Electrical Requirements
WARNING Electrical shock hazard. To avoid the risk of electrical shock, personal injury or death; verify electrical power is turned
off at the breaker box until the range is installed and ready to operate, installation by an authorized installer only.
Electrical Connection
RDEWD103
Max. amp usage
450 watts 3.8 amps
Electrical Requirements Check your national and local codes regarding this unit. Hard wire direct with seperate 120V/15 amp minimum 2-wire wtih ground circuit. Maximum amp usage.
Note: Use copper conductors ONLY!
Grounding Instructions This appliance must be connected to a grounded metal, permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the appliance.
With the appliance positioned in front of the cabinet opening, connect wire leads extending from the power supply to the terminal block of the unit. Make sure the colored wires of the terminal block are connected to the corresponding colored wires extending from the power supply.
98
General Information
When installing this unit directly below other units, only install with Viking built- in products.
Remove warming drawer carefully from carton. Remove all loose packaging and accessories.
It is the responsibility of the installer to comply with local codes. If no local codes are applicable, wire in accordance with the National Electrical Code, ANSI/NFPA 70 - latest edition.
This appliance is not fused. Protect with a proper sized fuse or circuit breaker and a GFI for outdoor models.
Line disconnect switch, circuit breaker, GFI (for outdoor models) or plug/receptacle of power cord connection should be readily accessible to the operator.
Ground unit per applicable electrical codes.
Any installation not matching the specifications discussed in these instructions will void the manufacturers warranty.
READ AND FOLLOW ALL WARNING AND CAUTION INFORMATION WHEN INSTALLING THIS APPLIANCE.
Moving, Handling and Unpacking Remove and discard all packing materials, including cardboard and tape on the outside and inside of the warming drawer.
Some stainless steel parts may have a plastic protective wrap which must be peeled off. The interior should be washed thoroughly with hot, soapy water to remove film residues and any dust or debris before being used, then rinsed and wiped dry. Solutions stronger than soap and water are rarely needed.
Installation - RDEWD
1
2
1
2
Pull out warming drawer pan until fully extended.
Slide finger along right and left side until you reach the black hand latches (located at the front of the rails). Pull
up on both the right and left latches and pull out drawer pan support.
2 (5.1 cm)
2 (5.1 cm)
Electrical opening (from rear)
3
2
1 1
4
Feed supply cord up through hole in rear of warming drawer.
1
2
5
Remove strain relief bracket and mounting screws on the terminals.
Attach the white (neutral) and black (line) lead terminals. Attach ground wire to the
center terminal.
1
2
6
Push supply cord toward terminal block to relieve strain, reattach supply cord strain relief
bracket over supply cord.
1110
7
Slide cavity assembly into the cabinet opening.
8
x4
9
Secure the warming drawer using four #8 mounting screws (four screws provided).
Replace drawer assembly.
Installation - RDEWD (cont.)
Final Preparation
All stainless steel body parts should be wiped with hot, soapy water and with a liquid cleaner designed for this material. If buildup occurs, DO NOT use steel wool, abrasive cloths, cleansers, or powders! If it is necessary to scrape stainless steel to remove encrusted materials, soak with hot, wet cloths to loosen the material, then use a wool or nylon scraper. DO NOT use a metal knife, spatula, or any other material tool to scrape stainless steel! Scratches are almost impossible to remove.
12 13
Service & Registration
Only authorized replacement parts may be used in performing service on the appliance. All servicing should be referred to a qualified technician.
Contact Viking Range Corporation, 1-888-VIKING1 (845-4641), for the nearest service parts distributor in your area or write to:
VIKING RANGE CORPORATION PREFERRED SERVICE
1803 Hwy 82W Greenwood, Mississippi 38930 USA
The serial number and model number for your appliance can be found by pulling drawer out until it stops and lifting inner lining. Rating/Serial plate is located on the left, rear side.
Record the following information indicated below. You will need it if service is ever required.
Model number ____________________________________________________________________________________
Serial number _____________________________________________________________________________________
Date of purchase __________________________________________________________________________________
Date installed ______________________________________________________________________________________
Dealer's name _____________________________________________________________________________________
Address ______________________________________________________________________________________
Related manuals for Viking RDEWD103 Drawer Installation Guide
Manualsnet FAQs
If you want to find out how the RDEWD103 Viking works, you can view and download the Viking RDEWD103 Drawer Installation Guide on the Manualsnet website.
Yes, we have the Installation Guide for Viking RDEWD103 as well as other Viking manuals. All you need to do is to use our search bar and find the user manual that you are looking for.
The Installation Guide should include all the details that are needed to use a Viking RDEWD103. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.
The best way to navigate the Viking RDEWD103 Drawer Installation Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.
This Viking RDEWD103 Drawer Installation Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.
You can download Viking RDEWD103 Drawer Installation Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.
To be able to print Viking RDEWD103 Drawer Installation Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Viking RDEWD103 Drawer Installation Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.