Viking DEWD171 Drawer Installation Guide PDF

1 of 4
1 of 4

Summary of Content for Viking DEWD171 Drawer Installation Guide PDF

Viking Range Corporation

111 Front Street

Greenwood, Mississippi 38930 USA

(662) 455-1200

For more product information,

call 1-888-VIKING1 (845-4641) or

visit the Viking web site

vikingrange.com

F1615N EN (022608J)

Built-In Electric Warming Drawers (Indoor and Outdoor Models)

VIKING

Viking Installation Guide

3

CABINET CUTOUT

Cavity Assy.

Identification Label Location

Drawer Assy.

Mounting Screws (4) - #8 x 3/4

A

Cabinet

9 1/4 (23.5 cm)

23 1/2 (59.7 cm)

INDOOR MODELS (VEWD, DEWD)

Model VEWD173 VEWD103 VEWD163 DEWD171 DEWD101

A 25 1/4 28 1/4 34 (64.1 cm) (71.8 cm) (86.4 cm)

OUTDOOR MODELS Cabinet

Cavity Assy.

Drawer Assy.

Model VEWD173T VEWD103T VEWD163T A 25 1/4 28 1/4 34

(64.1 cm) (71.8 cm) (86.4 cm)

23 1/2 (59.7 cm)

9 1/4 (23.5 cm)

A

2 (5.1 cm) min.

Seal all around opening with silicon caulk that is provided.

Identification Label Location

IMPORTANT - PLEASE READ AND FOLLOW Before beginning, please read these instructions completely and carefully.

Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty.

Please observe all local ordinances. If local codes are applicable, wire in accordance with the National Electrical Code, ANSI/NFPA 70 - latest edition.

WARNING - To reduce the risk of electric shock and fire, do not use a flexible power-supply cord with this appliance.

WARNING - FOR OUTDOOR INSTALLATION, INSTALLER MUST INSTALL A GROUND FAULT INTERRUPT.

The installer should leave these instructions with the consumer who should retain for local inspectors use and for future reference.

Make sure that incoming voltage is the same as unit rating. An electric rating plate specifying voltage, hertz, wattage, amps, and phase is attached to the product. Wiring the warming drawer with more voltage than it is rated for may cause severe damage to the thermostat, element, and other components. Wiring the warming drawer with less voltage than it is rated for may cause significant decrease in performance. To reduce the risk of fire, electric shock, or injury to persons, installation work and electrical wiring must be done by qualified people in accordance with all applicable codes and standards, including fire-rated conditions.

GENERAL INFORMATION When installing this unit directly below other units, only install with Viking built-in products Remove warming drawer carefully from carton. Remove all loose packaging and accessories. It is the responsibility of the installer to comply with local codes. If no local codes are applicable, wire in accordance with the National Electrical Code, ANSI/NFPA 70 - latest edition.

This appliance is not fused. Protect with a proper sized fuse or circuit breaker and a GFI for outdoor models.

Line disconnect switch, circuit breaker, GFI (for outdoor models) or plug/receptacle of power cord connection should be readily accessible to the operator.

Ground unit per applicable electrical codes. Any installation not matching the specifications discussed in these instructions will void the manufacturers warranty.

ELECTRICAL CONNECTION - USE COPPER CONDUCTORS ONLY.

GROUNDING INSTRUCTIONS This appliance must be connected to a grounded metal, permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and

connected to the equipment-grounding terminal or lead on the appliance.

With the appliance positioned in front of the cabinet opening, connect wire leads extending from the power supply to the terminal block of the unit. Make sure the colored wires of the terminal block are connected to the corresponding colored wires extending from the power supply.

2

BASIC SPECIFICATIONS MODEL VEWD173 VEWD103 VEWD163

VEWD173T VEWD103T VEWD163T DEWD171 DEWD101 DFWD171 DFWD101

Interior width 17 1/4 (43.8 cm) 20 1/2 (52.1 cm) 25 (63.5 cm)

Interior height 6 (15.2 cm) 6 (15.2 cm) 6 (15.2 cm)

Interior depth 22 3/4 (27.8 cm) 22 3/4 (27.8 cm) 22 3/4 (27.8 cm)

Electrical Hard wire direct with separate 15 amp minimum 2-wire with

Requirements ground circuit; 120 VAC/50-60 Hz

Max. Amp Usage 425 watts 450 watts 550 watts

3.6 amps 3.8 amps 4.6 amps

Approx. shipping Wt. 80 lb. (36 kg) 90 lb. (40.5 kg) 110 lb. (49.5 kg)

WARNING!

FRONT VEWD

FRONT DEWD

FRONT DFWD

REAR

2 (5.1 cm)

2 (5.1 cm)

10 (25.4 cm)

B

10 (25.4 cm)

B

B

C

8 31/32 (22.8 cm)

(When facing cabinet, opening is located on right side.)

MODEL VEWD173 DFWD171 VEWD103 DFWD101 VEWD163 VEWD173T VEWD103T VEWD163T DEWD173 DEWD103

B 26 1/2 26 29 1/2 29 35 1/4 (67.3 cm) (66.0 cm) (74.9 cm) (73.7 cm) (89.5 cm)

C 24 7/8 24 7/8 27 7/8 27 7/8 33 5/8 (63.2 cm) (63.2 cm) (70.8 cm) (70.8 cm) (85.4 cm)

120V Electrical opening

5

10 1/2 (26.7 cm)

3/4 thick

4

CABINET INSTALLATION To remove drawer assembly, pull warming drawer pan out until fully extended. Slide finger along the right and left side until you reach the black hand latches (located at the front of the rails). Pull up on both the right and left latches and pull drawer pan support completely out.

For outdoor models ONLY - Apply silicon caulk that is provided all around the back of the warming drawer trim. Slide cavity assembly into cabinet opening. Drill (4) pilot holes in cabinet using 1/8 drill bit. Permanently secure the warming drawer using the (4) #8 mounting screws provided.

Replace drawer assembly.

CUSTOM FRONT INSTALLATION - DFWD MODELS

Open the drawer and remove the pan. Center the custom front on the inside panel. Attach the custom front with the (6) six #8 x 3/4 screws provided.

CABINET CUTOUT DFWD MODELS

24 (61.0 cm)

9 5/8 (24.4 cm)

Cabinet

Model DFWD171 DFWD101 25 1/4 28 1/4

A (64.1 cm) (71.8 cm)

Cavity Assy. Mounting Screws (4) - #8 x 3/4 (2 per side) (6) - #8 x 3/4 screws to

attach custom front

custom front

Identification Label Location

76

SIDE VEWD

26 3/8 (67.0 cm)

22 7/8 (58.1 cm) 25 3/4 (65.4 cm

Manualsnet FAQs

If you want to find out how the DEWD171 Viking works, you can view and download the Viking DEWD171 Drawer Installation Guide on the Manualsnet website.

Yes, we have the Installation Guide for Viking DEWD171 as well as other Viking manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Installation Guide should include all the details that are needed to use a Viking DEWD171. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Viking DEWD171 Drawer Installation Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Viking DEWD171 Drawer Installation Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Viking DEWD171 Drawer Installation Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Viking DEWD171 Drawer Installation Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Viking DEWD171 Drawer Installation Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.