Viking DEWD101 Drawer Installation Guide PDF

1 of 4
1 of 4

Summary of Content for Viking DEWD101 Drawer Installation Guide PDF

Viking Installation Guide

F20022J EN (022608J)

Designer Series Built-In Electric Warming Drawer (DEWD Designer Model/DFWD Full Overlay Model)

Viking Range Corporation

111 Front Street

Greenwood, Mississippi 38930 USA

(662) 455-1200

For product information,

call 1-888-VIKING1 (845-4641)

or visit the Viking Web site at

vikingrange.com

3

DEWD - CABINET CUTOUT

To remove drawer assembly, pull warming drawer pan out until fully extended. Slide finger along the right and left side until you reach the black hand latches (located at the front of the rails). Pull up on both the right and left latches and pull drawer pan support completely out.

Slide cavity assembly into cabinet opening. Drill (4) pilot holes in cabinet using 1/8 drill bit. Permanently secure the warming drawer using the (4) #8 mounting screws provided.

Replace drawer assembly.

Model DEWD170 DEWD100 25 1/4 28 1/4

A (64.1 cm) (71.8 cm)

CABINET INSTALLATION

Cabinet

mounting screws (4) - #8 x 3/4

cavity assy drawer

assy9 5/8 (24.4 cm)

24 (61.0 cm)

IMPORTANT - PLEASE READ AND FOLLOW Before beginning, please read these instructions completely and carefully. Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty. Please observe all local ordinances. If local codes are applicable, wire in accordance with the National Electrical Code, ANSI/NFPA 70 - latest edition.

WARNING - To reduce the risk of electric shock and fire, do not use a flexible power-supply cord with this appliance.

The installer should leave these instructions with the consumer who should retain for local inspectors use and for future reference.

WARNING!!! Make sure that incoming voltage is the same as unit rating. An electric rating plate specifying voltage, hertz, wattage, amps, and phase is attached to the product. Wiring the warming drawer with more voltage than it is rated for may cause severe damage to the thermostat, element, and other components. Wiring the warming drawer with less voltage than it is rated for may cause significant decrease in performance. To reduce the risk of fire, electric shock, or injury to persons, installation work and electrical wiring must be done by qualified people in accordance with all applicable codes and standards, including fire-rated conditions.

GENERAL INFORMATION THIS UNIT IS NOT TO BE INSTALLED BELOW CABINETS OR WALL MOUNTED. When installing this unit directly below other units, only install with Viking built-in products Remove warming drawer carefully from carton. Remove all loose packaging and accessories. It is the responsibility of the installer to comply with local codes. If no local codes are applicable, wire in accordance with the National Electrical Code, ANSI/NFPA 70 - latest edition.

This appliance is not fused. Protect with a proper sized fuse or circuit breaker. Line disconnect switch, circuit breaker, or plug/receptacle of power cord connection should be readily accessible to the operator.

Ground unit per applicable electrical codes. Any installation not matching the specifications discussed in these instructions will void the manufacturers warranty.

ELECTRICAL CONNECTION - USE COPPER CONDUCTORS ONLY. With the appliance positioned in front of the cabinet opening, connect wire leads extending from the power supply to the terminal block of the unit. Make sure the colored wires of the terminal block are connected to the corresponding colored wires extending from the power supply.

2

5

To remove drawer assembly, pull warming drawer pan out until fully extended. Slide finger along the right and left side until you reach the black hand latches (located at the front of the rails). Pull up on both the right and left latches and pull drawer pan support completely out.

Slide cavity assembly into cabinet opening. Drill (4) pilot holes in cabinet using 1/8 drill bit. Permanently secure the warming drawer using the (4) #8 mounting screws provided.

Replace drawer assembly.

Model DFWD170 DFWD100 25 1/4 28 1/4

A (64.1 cm) (71.8 cm)

CABINET INSTALLATION

CUSTOM FRONT INSTALLATION Open the drawer and remove the pan. Center the custom front and insulation around the inside panel. *NOTE: Make sure the insulation provided is used between the custom panel and the inside door panel. Attach the custom front with the (6) six #8 x 3/4 screws provided.

Cabinet

Cavity Assy.Mounting Screws (4) - #8 x 3/4

(6) - #8 x 3/4 screws to attach custom front

custom frontinsulation

DFWD - CABINET CUTOUT

24 (61.0 cm)

9 5/8 (24.4 cm)

FRONT

REAR

2 1/2 (6.4 cm)

2 1/2 (6.4 cm)

SIDE

10 (25.4 cm)

B

C

9 1/2 (24.1 cm)

27 (68.6 cm)

22 (55.9 cm) 23 (58.4 cm)

1 1/2 (3.8 cm)

4

MODEL DEWD170 DEWD100

B 26 1/2(67.3 cm) 29 1/2 (74.9 cm)

C 24 7/8(63.2 cm) 27 7/8 (70.8 cm)

Interior width 18 7/8 (47.9 cm) 21 7/8 (55.6 cm)

Interior height 5 7/16 (13.8 cm) 5 7/16 (13.8 cm)

Interior depth 21 3/16 (53.8 cm) 21 3/16 (53.8 cm)

Approx. shipping Weight 80 lb. (36 kg) 90 lb. (40.5 kg)

120V Electrical opening

ELECTRIC DATA Hard wire direct with separate 15 amp minimum 2-wire with ground circuit 120 VAC/50-60 Hz DEWD170/DFWD170 - 425 watts/3.6 max. amps DEWD100/DFWD100 - 475 watts/4.0 max. amps

6

MODEL DFWD170 DFWD100

B 26(66.0 cm) 29 (73.7 cm)

C 24 7/8(63.2 cm) 27 7/8 (70.8 cm)

Interior width 18 7/8 (47.9 cm) 21 7/8 (55.6 cm)

Interior height 5 7/16 (13.8 cm) 5 7/16 (13.8 cm)

Interior depth 21 3/16 (53.8 cm) 21 3/16 (53.8 cm)

Approx. shipping Weight 75 lb. (33.7 kg) 90 lb. (40.5 kg)

FRONT

<

Manualsnet FAQs

If you want to find out how the DEWD101 Viking works, you can view and download the Viking DEWD101 Drawer Installation Guide on the Manualsnet website.

Yes, we have the Installation Guide for Viking DEWD101 as well as other Viking manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Installation Guide should include all the details that are needed to use a Viking DEWD101. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Viking DEWD101 Drawer Installation Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Viking DEWD101 Drawer Installation Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Viking DEWD101 Drawer Installation Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Viking DEWD101 Drawer Installation Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Viking DEWD101 Drawer Installation Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.