Summary of Content for Viking RS30CBF4 Curb Installation Guide PDF
Range / Rangetop Rear Island Trim / Backguard / High Shelf Accessories
Range Curb Base Fronts
Rear Trim Accessories
MODELS BACKGUARD HIGH SHELF CURB BASE
C/VDSC530 C/VESC530 C/VISC530 VGRT530 C/VER530 C/VIR530
P30BG8SS B304H24SS P30CBF4SS
VGCC536 C/VDSC536 VGIC5361 VGRT536
P36BG8SS B36HS24SS P36CBF4SS
P48BG8SS B48HS24SS P48CBF4SS
P60BG8SS B60HS24SS P60CBF4SS
VGR530 C/VDR530 VGIC5302
BG8530SS HS24530SS P30CBF4SS
VGR536 C/VDR536 VGIC5362
BG8536SS HS24536SS P36CBF4SS
BG8548SS HS24548SS P48CBF4SS
BG8560SS HS24560SS P60CBF4SS
C/RVER3301 RD30BG6SS N/A P30CBF4SS
RVGR3301 RVGR3302 RVGR3303 RVDR3301 RVDR3302
RD301BG6SS N/A P30CBF4SS
Rear Trim Accessories
All rear trim devices are installed in the same basic way.
ATTACHING REAR TRIM (Illustration I)
Grasp the trim on each end and carefully place in the channels (B) located at each rear corner of the product. Align the screw holes (A) at each end of the trim device with the holes (A) in each rear channel of the product. Secure with the 4 enclosed screws.
RANGETOP REAR VIEW
RANGE REAR VIEW
ATTACHING SHELF ON HIGH -SHELF (Illustration 2)
Place the top rolled edge (X) over the front lip of the high-shelf back trim and secure with the 4 enclosed screws, two at each end. CAUTION: Do not place heavy pans and pots on the High Shelf or light fl ammables liquids.
WARNING To reduce the risk of fi re or injury to persons, check to make sure all packaging has been removed from the outside and inside parts of the rear trim device before installing. MAKE SURE ALL CORRUGATED MATERIAL IS REMOVED FROM INSIDE THE HIGH SHELF.
Rear Trim Accessories
ATTACHING BACKGUARD (Illustration 3)
Backguards come equipped with Nylon Spacers (See Figure 1), which are needed to space the range off a combustible wall a prescribed safe distance.
These spacers can also be removed if used with any of the models* listed below: C/VGCC530 C/VDSC530 C/VDSC536 C/VGRT530 C/VGRT536
*If you have one of these models, the spacers are not required, even if with a combustible wall.
C/VGCC560 ranges require that two 1 standoff spacers be attached to the back of the range when using a range with a backguard against a combustible surface. (See Figure 2)
Once you determine whether or not your product needs the provided spacers, the backguard is ready to be attached. Simply slide the backguard down onto the rear of the unit behind the spacers and attach using the (4) screws provided.
ATTACHING ISLAND TRIM (Illustration 4)
IMPORTANT: USE OF ISLAND TRIM WITH AND WITHOUT 6 (15.2 CM) CLEARANCE. Normal installation for island trim on either a range or rangetop is in an island/peninsula or where there is a minimum clearance of 6(15.2 cm) to any type of wall at the rear of the unit. Ranges and rangetops with an island trim installation can be installed at zero clearance to the rear wall as long as the wall is non-combustible. The responsibility for ensuring that the rear wall is non-combus- tible and heat resistant lies with the individual owner and/or end user. Only in those cases where the island trim is installed with 6 (15.2 cm) of minimum clearance to a rear wall, or when a truly non-combustible material is used, will the warranty apply. In no case will Viking Range, LLC accept responsibility for any claims which may result from heat damage against a rear wall, including cosmetic damage. It is the total responsibility of the owner/end user to ensure that the material utilized in such applications is not only non-combustible, but is also truly heat-resistant.
Rear Trim Accessories
STANDARD CURB BASE FRONT 1. The standard curb base front (A) is completely assembled. 2. Remove the assembly from the carton and simply clip onto the front range legs. 3. The assembly is adjustable about 2 (5.1 cm) front to back so that alignment with the cabinet toe front is possible. Loosen
brackets on each side, but allow snug fi t. Clip assembly onto range legs; determine front to back setting; remove, tighten bolts, and reattach.
ALTERNATE CURB BASE VIEW FOR CUSTOM RANGES
Important Note: The range must be installed as specifi ed in the range installation guide for proper airfl ow when using the standard curb base.
CUSTOM CURB BASE FRONT 1. Remove the standard curb base front assembly from the carton. 2. Remove the front (A) from the mounting assembly (B). 3. Attach locally supplied front (C) to the mounting assembly (B) ad simply clip onto the front range legs.
Important Note: The locally supplied front must not be any taller than 3-1/8 (7.9 cm) tall. Fronts taller than 3-1/8 (7.9 cm) could obstruct the airfl ow.
4. The assembly is adjustable about 2 (5.1 cm) front to back so that alignment with the cabinet toe front is possible. Loosen brack- ets on each side, but allow snug fi t. Clip assembly onto range legs; determine front to back setting; remove, tighten bolts, and reattach.
Important Note: The range must be installed as specifi ed in the range installation guide for proper airfl ow when using the st
If you want to find out how the RS30CBF4 Viking works, you can view and download the Viking RS30CBF4 Curb Installation Guide on the Manualsnet website.
Yes, we have the Installation Guide for Viking RS30CBF4 as well as other Viking manuals. All you need to do is to use our search bar and find the user manual that you are looking for.
The Installation Guide should include all the details that are needed to use a Viking RS30CBF4. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.
The best way to navigate the Viking RS30CBF4 Curb Installation Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.
This Viking RS30CBF4 Curb Installation Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.
You can download Viking RS30CBF4 Curb Installation Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.
To be able to print Viking RS30CBF4 Curb Installation Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Viking RS30CBF4 Curb Installation Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.