Contents

Viking DETU200 Cooktop Installation Guide PDF

1 of 20
1 of 20

Summary of Content for Viking DETU200 Cooktop Installation Guide PDF

Viking Installation Guide

Designer Built-In Electric Cooktops

Table of Contents

Warnings & Important Safety Instructions _______________________________________________3 Dimensions (30) ____________________________________________________________________6 Dimensions (36) ____________________________________________________________________7 Specifications _______________________________________________________________________8 Cutout Dimensions __________________________________________________________________9 Downdraft Dimensions ______________________________________________________________9 Clearance Dimensions (Proximity to Cabinets) ___________________________________________9 Clearance Dimensions (Wood/Composite or Steel Overlay) ______________________________11 Electrical Requirements _____________________________________________________________12 General Information ________________________________________________________________14 Installation_________________________________________________________________________15

Electrical Connection ____________________________________________________________16 Final Installation ________________________________________________________________16

Final Preparation ___________________________________________________________________17 Performance Checklist ______________________________________________________________17 Service & Registration_______________________________________________________________18

IMPORTANT Before beginning, read these instructions

thoroughly and carefully.

Installation and service must be performed by a qualified installer, service agency.

DO NOT remove permanently affixed labels, warnings, or plates from the product as this may void the warranty.

Observe all local and national codes, requirements and ordinances.

Write down the model and serial numbers before installing the cooktop. Both numbers are on the serial rating plate located on bottom of cooktop box.

Installation must conform with local codes or in the absence of codes, the national electric code: ANSI/NFPA 70-latest edition** or CSA standards C22. 1-94, Canadian Electrical Code, part No. 0-M91 - latest edition*** and all local codes and ordinances.

In Canada: Installation must be in accordance with the current CAN/CGA B149.1 & 2 Gas Installation codes and with the current CSA C22.1 Canadian Electrical Codes Part 1 and/or local codes.

Copies of the standards listed may be obtained from: ** National Fire Protection Association One Batterymarch Park Quincy, Massachusetts 02269 *** CSA International 8501 East Pleasant Valley Rd. Cleveland, OH 44131-5575

Installers should leave these instructions with the consumer who should retain them for the local inspectors use and for future reference.

3

Please Read and Follow

Your safety and the safety of others is very important.

We have provided many important safety messages in this manual and on your appliance. ALWAYS read and obey all safety messages.

This is the safety alert symbol. This symbol alerts you to hazards that can kill or hurt you and others.

All safety messages will be preceded by the safety alert symbol and the word DANGER, WARNING or CAUTION. These words mean:

Hazards or unsafe practices which WILL result in severe personal

injury or death

DANGER

Hazards or unsafe practices which COULD result in severe personal

injury or death

Hazards or unsafe practices which COULD result in minor personal injury

or property damage.

All safety messages will identify the hazard, tell you how to reduce the chance of injury, and tell you what can happen if

the instructions are not followed.

WARNING

CAUTION

IMPORTANT

4

Please Read and Follow

FIRE/EXPLOSION HAZARD IF THE INFORMATION IN THIS MANUAL IS NOT

FOLLOWED EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY, OR DEATH. DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

DANGER ELECTRICAL GROUNDING INSTRUCTIONS The cooktop must be electrically grounded in accordance with local codes or, in the absence of codes, with the ANSI/NFPA No. 70-latest edition. Installation should be made by a licensed electrician. This appliance is equipped with a three-prong grounding plug for your protection against shock hazard and should be plugged directly into a properly grounded receptacle. DO NOT cut or remove the grounding prong from the plug.

For personal safety, this appliance must be properly grounded. DO NOT under any circumstances cut or remove the third (ground) prong from the power plug.

WARNING

BURN HAZARD The use of cabinets for storage above the appliance may result in a potential burn hazard. Combustible items may ignite, metallic items may become hot and cause burns. If a cabinet storage is to be provided the risk can be reduced by installing a range hood that projects horizontally a minimum of 5 (12.7 cm) beyond the bottom of the cabinets.

CAUTION

IMPORTANT

5

Please Read and Follow

This appliance shall not be used for space heating. This information is based on safety considerations.

WARNING SITE PREPARATION It is recommended that a thorough site inspection be conducted PRIOR to unpacking and moving this appliance.

WARNING

It is the customer's responsibility to contact a qualified electrical installer. To assure that the electrical installation is Adequate and in conformity with national electrical code: ANSI/NFPA 70-latest edition** or CSA standards C22.1-94, Canadian Electrical Code, part No.0-M91 - latest edition*** and all local codes and ordinances.

WARNING

THE CONDUIT IS 3 FEET LONG The junction box must be located where it will allow considerable slack in the conduit for serviceability.

WARNING

Dimensions

6

21 (53.3 cm)

30-3/4 (78.1 cm)

3-1/8* (7.9 cm)

4-1/4 (10.8 cm)

28 (71.1 cm)

18-9/16 (47.2 cm)12

(30.5 cm)

3-1/4 (8.3 cm)

Power conduit

30 Electric Cooktop

*Note: Dimension includes screw head.

Dimensions

7

21 (53.3 cm)

3-1/8* (7.9 cm) 4-1/4

(10.8 cm)

36-3/4 (93.4 cm)

33-3/8 (84.7 cm)

18-9/16 (47.2 cm)

3-1/4 (8.3 cm)

Power conduit

12 (30.5 cm)

36 Electric Cooktop

*Note: Dimension includes screw head.

Specifications

8

Designer Electric Cooktops Description DETU200-4B DETU260-5B

Overall width 30-3/4 (78.1 cm) 36-3/4 (93.3 cm)

Overall height (from top of cooktop to bottom of conduit)

4-1/4 (10.8 cm)

Overall depth from rear 21 (53.3 cm)

Cutout width 28-3/4 (72.9 cm) min. to 29 (73.7 cm) max.

34 (86.4 cm) min. to 34-9/16 (87.8 cm) max.

Cutout height 3-1/8 (7.9 cm)

Cutout depth 19-1/4 (49.0 cm) min. to 19-5/8 (49.8 cm)

Electrical requirements 3-wire, 240-208/120VAC/60Hz; 40 amp connection. Unit is equipped with

No. 10 ground wire in conduit. Should be fused separately.

3-wire, 240-208/120VAC/60Hz; 60 amp connection. Unit is equipped with

No. 10 ground wire in conduit. Should be fused separately.

Maximum amp usage 240V35.0 amps (8.4 kw) 208V30.3 amps (6.3 kw)

240V45.0 amps (10.8 kw) 208V40.0 amps (8.3 kw)

Surface element rating Left front

Bridge

Left rear

Center

Right front

Right rear

240V 208V 1,800 watts 1,350 watts

800 watts 600 watts

1,800 watts 1,350 watts

1,500 watts 1,125 watts

N/A N/A

2,500/1,600/800 watts 1,875/1,200/600 watts

240V 208V 1,800 watts 1,350 watts

800 watts 600 watts

1,800 watts 1,350 watts

2,500/1,600/800 watts 1,875/1,200/600 watts

1,500 watts 1,125 watts

2,100 watts 1,575 watts

Approximate shipping weight

35 lb. (13.1 kg) 60 lb. (27.2 kg)

9

A

B

Note: Based on 24 deep cabinet with 3/4 backsplash.

DETU200 DETU260

A 28-3/4 (72.9 cm) min. to 29 (73.7 cm) max.

34 (86.4 cm) min. to 34-9/16 (87.2 cm) max.

B 19-1/4 (49.0 cm) min. to 19-5/8 (49.8 cm) max.

Cutout Dimensions

Note: Refer to the downdraft installation instructions.

Downdraft Dimensions

DETU200 w/DIPR100 DETU260 w/DIPR160

A 28-3/4 (73.0 cm) 34 (86.4 cm)

B 20-1/4 (51.4 cm)

C 27 (68.6 cm) 33 (84.0 cm)

D 2-1/4 (5.7 cm)

E 7/8 (1.9 cm) 7/8 (1.9 cm)

F 7/8 (1.9 cm) 7/8 (1.9 cm)

C

E F

D

A

B

Clearance Dimensions (Proximity to Cabinets)

30 min.

(76.2 cm)

13 max.

(33.0 cm)

6 min. (15.2 cm)

18 min.

(45.7 cm)

36 min.

(91.4 cm) 1-1/2 min.

(3.8 cm)* 2-1/2 min.

(6.35 cm)*

Note: Dimensions shown are for use with combustible surfaces unless otherwise stated.

Proximity to Side Cabinet Installation The cooktop may be installed directly to

existing base cabinets. The cooktop CANNOT be installed directly

adjacent to sidewalls, tall cabinets, tall appliances, or other side vertical surfaces above 36 (91.4 cm) high. There must be a minimum of 6 (15.2 cm) side clearance from the cooktop to such combustible surfaces above the 36 (91.4 cm) counter height.

Within the 6 (15.2 cm) side clearance to combustible vertical surfaces above 36 (91.4 cm), the maximum wall cabinet depth must be 13 (33.0 cm) and wall cabinets within this 6 (15.2 cm) side clearance must be 18 (45.7 cm) above the 36 (91.4 cm) high countertop.

Wall cabinet above the cooktop must be a minimum of 30 (76.2 cm) above the countertop for a full width of the cooktop. This minimum height requirement does not apply if a rangehood is installed over the cooking surface.

Minimum Clearances from Adjacent Combustible Construction Wall cabinets directly above the product must be

minimum 30 (76.2 cm) above the countertop Sidesminimum 6 (15.2 cm) Rearminimum 1-1/2 (3.8 cm) From edge of cutout and front edge of

countertop 2-1/2 (6.35 cm) Within 6 (15.2) side clearance; wall cabinets

no deeper than 13 (33.0 cm) Countertop depth 25 (63.5 cm) Overhead cabinet depth from rear maximum

13 (33.0 cm) Side cabinet height from countertop

minimum 18 (45.7 cm)

10

11

66min. (167.6 cm)to72max. (182.9 cm)

66min. (167.6 cm)to72max. (182.9 cm)

24

(61.0 cm)

or

27

(38.6 cm)

30

(76.2 cm)

6

(15.2 cm )

Wood/Composite

or Steel Overlay

Wood/Composite

or Steel Overlay

30min. (76.2 cm)to36max. (91.4 cm)

30min. (76.2 cm)to36max. (91.4 cm)

Wall Installation

Island Installation

Clearance Dimensions (Wood/Composite or Steel Overlay)

The bottom of a standard hood should be 30 (76.2 cm) min. to 36 (91.4 cm) max. above the countertop. This would typically result in the bottom of the hood being 66 (167.6 cm) to 72 (182.9 cm) above the floor. These dimensions provide for safe and efficient operation of the hood. Refer to the range hood installation instructions for additional information.

Electrical Connections

This cooktop does not require a neutral connection. If the cooktop is to be completely enclosed in a cabinet, feed the cooktop cable through the opening in the cabinet. Make the electrical connection following the appropriate steps for your installation.

Your cooktop must be connected to the proper electrical voltage and frequency as specified in the table on the right.

Connect with copper wire only If the house has aluminum wiring, follow the procedure below:

1. Connect the aluminum wiring to the copper wire by using special connectors designed and Underwriters Laboratories-listed for joining copper to aluminum. Follow the electrical connector manufacturer's recommended procedure.

2. Aluminum/copper connection must conform with local codes and industry- accepted wiring practices.

The flexible conduit (supplied) 3 feet long (100 cm) located at the right rear of the cooktop bottom box should be connected directly to junction box. DO NOT cut the conduit. A U.L - or CSA - listed conduit connector must be provided at each end of the power supply cable (at the cooktop and at the junction box.) A time delay fuse or circuit breaker is recommended.

DO NOT ground to a gas pipe. DO NOT have a fuse in the grounding or neutral circuit. Fuse both supply (phase) lines.

National Fire Protection Association Batter/march Park Quincy, Massachusetts 02269 A three-wire, single phase, 240 Volt 60 cycle electrical system (properly circuit protected to meet Local Codes of NFPA No.70) must be provided. Unit must be properly grounded in accordance with local wiring code. The chart below recommends the minimum circuit protector and wire size if the appliance is the only unit on the circuit. If smaller sizes of wire are used, the unit efficiency will be reduced and a fire hazard may be created. It is advisable that the electrical wiring and hookup be accomplished by a competent electrician.

Be sure your appliance is properly installed and grounded by a qualified technician. Ask your dealer to recommend a qualified technician or an authorized repair service. This cooktop does not require a neutral connection. If the cooktop Is to be completely enclosed In a cabinet, feed the cooktop cable through the opening in the cabinet. Make the electrical connection following the appropriate steps for your installation.

12

Improper connection of aluminum house wiring to the copper leads can result in a serious problem.

WARNING

ELECTRICAL SHOCK HAZARD The models may be powered at 240V or 208V.

WARNING

ELECTRICAL SHOCK HAZARD Disconnect power before servicing the product. Failure to do so could result in death or electric shock.

WARNING

Recommended Minimum

KW Rating on serial plate

Circuit protection in amperes

Wire Size (AWG)

0-4.8 20 12

4.9-6.9 30 10

7.0-9.9 40 8

10.0-11.9 50 8

12.0-14.9 60 6

Electrical Requirements

13

This appliance is manufactured with a green ground wire connected to the cooktop chassis. After making sure that the power has been turned off, connect the flexible conduit from the cooktop to the junction box using a U.L. listed conduit connector. The instructions provided below present the most common way of connecting the cooktops. Your local codes and ordinances, of course, take precedence over these instructions. Complete electrical connections according to local codes and ordinances.

Grounding through the neutral conductor is prohibited for new branch-circuit installations (1996 NEC); mobile homes; and recreational vehicles, or in an area where local codes prohibit grounding through the neutral conductor.

3-Wire branch circuit Where local codes allow the connection of ground wire from the cooktop to the branch circuit neutral wire (gray or white colored wire) proceed as follows.

1. If local codes permit, connect the green GROUND wire from the cooktop to the branch circuit neutral wire (gray or white colored wire).

2. Connect the red and black leads from the cooktop to the corresponding leads in the junction box.

4-Wire branch circuit 1. Connect the green ground wire from the

cooktop to the ground wire in the junction box (bare or green colored wire).

2. Connect the red and black leads from the cooktop to the corresponding leads in the junction box.

3. Connect the white wire from the cooktop to the neutral (gray or white) wire in the junction box.

4. Terminate and insulate the neutral (gray or white colored wire) in the junction box.

Electrical Requirements

ELECTRICAL SHOCK HAZARD Frame grounded to neutral of appliance through a link.

WARNING

Clearance Dimensions

General Information

Site Preparation Note: It is recommended that a thorough site inspection be conducted prior to unpacking and moving this appliance.

Chamfer all exposed edges of decorative laminate to prevent damage from chipping.

Radius corners of cutout and file to Insure smooth edges and prevent corner cracking. Recommend 1/4or 3/8 diameter drill In each corner.

Rough edges, inside corners which have not been rounded and forced fits can contribute to cracking of the countertop laminate.

Confirm available access to adequate power see electrical requirements.

Be sure that the countertop for this appliance is level and cut according to the cutout requirements and dimensionssee cutout requirements and dimensions.

All wall coverings, countertop and cabinets around the cooktop should withstand heat up to 200F (90C).

Keep appliance free from combustible materials, gasoline, and other flammable vapors.

Installation Procedure Remove packaging materials and literature package from the cooktop before beginning installation. Remove Installation Instructions from literature pack and read them carefully before you begin.

ELECTRICAL SHOCK HAZARD The models may be powered at 240V or 208V.

WARNING

DO NOT use an extension cord with this appliance. Such use may result in fire, electrical shock or other personal injury.

WARNING

14

Install junction box so that it can be reached through the front of cabinet.

*

THE CONDUIT IS 3 FEET LONG The junction box must be located where it will allow considerable slack in the conduit for serviceability.

WARNING

Junction Box Location

*Note: Minimum from bottom of countertop and adjacent right-side cabinet to top of junction box.

15

For solid surface material installations such as Surel and Corian, consult with solid surface manufacturer. Apply heat reflective tape such as Scotch Aluminum Foil Tape #425 or #427 around the cutout so that it folds over on the top and sides.

DO NOT wrap the tape underneath the cooktop. Be sure the tape extends beyond the outermost flange of the cooktop. All corners should be covered with tape.

IMPORTANT

1 2 Optional Gasket

Turn the cooktop upside down and place on the packaged foam top. Note: Make sure there are no loose objects on

the cooktop before turning upside down.

Peel away the plastic covering and place the gasket material all the way around the burner flange.

IMPORTANT: Make sure the corners are covered completely, leaving no air gaps.

3

Installation

Turn the cooktop over and place into countertop opening.

16

1

Install screws into brackets to secure cooktop to countertop.

4 w

ire

1b

Neutral Green

Green

Black Red

Connect the red, black, and green leads from the unit conduit to the corresponding leads in the junction box.

Electrical Connection

Final Installation 3

w ire

1a

Neutral Green

Black

Red

Connect the red and black leads from the unit conduit to the corresponding leads in the junction box.

THE CONDUIT IS 3 FEET LONG The junction box must be located where it will allow considerable slack in the conduit for serviceability.

WARNING

17

New units are cleaned at the factory to remove any visible signs of dirt, oil, grease, etc. remaining from the manufacturing process. Some stainless steel parts may have a plastic protective wrapper which must be peeled off. The cooktop should be washed thoroughly with hot, soapy water and then rinsed and wiped dry to remove these film residues and any installation dust or debris before being used for food preparation.

A qualified installer should carry out the following checks:

h Check top surface elements 1. Glow red when turned on.

h Check hot surface indicator lights 1. Glow red when corresponding element is

hot.

Any adjustments necessary that are a result of the installer not following instructions will be the responsibility of the installer, dealer of the end user of this product.

Performance Checklist

Final Preparation

18

Service & Registration Only authorized replacement parts may be used in performing service on the appliance. All servicing should be referred to a qualified technician.

Contact Viking Range Corporation, 1-888-VIKING1 (845-4641), for the nearest service parts distributor in your area or write to:

VIKING RANGE CORPORATION PREFERRED SERVICE

1803 Hwy 82W Greenwood, Mississippi 38930 USA

The serial number and model number for your appliance can be found by looking under the cooktop.

Record the following information indicated below. You will need it if service is ever required.

Model number ____________________________________________________________________________________

Serial number _____________________________________________________________________________________

Date of purchase __________________________________________________________________________________

Date installed ______________________________________________________________________________________

Dealer's name _____________________________________________________________________________________

Address ___________________________________________________________________________________________

These installation instructions should remain with the unit for future reference.

19

Notes ________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

________________________________________________________________________________________________________________________________________________________

Manualsnet FAQs

If you want to find out how the DETU200 Viking works, you can view and download the Viking DETU200 Cooktop Installation Guide on the Manualsnet website.

Yes, we have the Installation Guide for Viking DETU200 as well as other Viking manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Installation Guide should include all the details that are needed to use a Viking DETU200. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Viking DETU200 Cooktop Installation Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Viking DETU200 Cooktop Installation Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Viking DETU200 Cooktop Installation Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Viking DETU200 Cooktop Installation Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Viking DETU200 Cooktop Installation Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.