Toyota 4Runner TVIP V3 RS3200 2002 SUV Owner's Guide PDF
Summary of Content for Toyota 4Runner TVIP V3 RS3200 2002 SUV Owner's Guide PDF
2000- 4RUNNER TVIP V3 RS3200 OWNERS GUIDE
Remote Keyless Security system
Designed Specifically for your Vehicle
owners guide
RS3200
090002-2475A700 Rev. E 12/01/05
090002-2475A700
Page 20 TOYOTA RS3200 REMOTE KEYLESS Security system
To better understand the features and functions of this security system, please read this Owners Guide completely prior to use.
TABLE OF CONTENTS
DESCRIPTION PAGE INTRODUCTION 2
REMOTE CONTROL INFORMATION THE REMOTE CONTROL INCLUDED WITH YOUR SYSTEM 3
BRIEF DESCRIPTIONRS3200 FEATURES 4, 5
OPERATION ARMING THE RS3200 (except PASSIVE ARMING) 6 DISARMING THE RS3200 (except PASSIVE DISARMING) 7 PASSIVE (AUTOMATIC) ARMING & DISARMING 8 AUTOMATIC REARMING 9 ARMING SUSPENSION 9
MISCELLANEOUS DOOR AJAR WARNING 10 IGNITION-CONTROLLED DOOR LOCKING/UNLOCKING 10 REMOTE CONTROL RANGE 10
ALARM INFORMATION PANIC MODE OPERATION 11 ALARM TRIGGERS 12 ALARM DESCRIPTIONS 13 STOPPING AN ALARM 13
GLASS BREAKAGE SENSOR INFORMATION GLASS BREAKAGE SENSOR CHECK PROCEDURE 14
PROGRAMMING PASSIVE (AUTOMATIC) ARMING AND ENTRY DELAY 15 DRIVERS DOOR/ALL DOORS UNLOCK SELECTION 16, 17 IGNITION-CONTROLLED DOOR LOCKING/UNLOCKING 18
REMOTE CONTROL BATTERY REPLACEMENT REMOVE THE BATTERY 19 INSTALL THE BATTERY 20
WARNING AND CAUTION INFORMATION 21
REMOTE CONTROL BATTERY REPLACEMENT INSTALL THE BATTERY
1. Hold the battery with the plus side up.
Handle the battery with a cloth or tissue; body oils and moisture can interfere with operation and may reduce the life of the battery.
2. Insert the new battery as shown.
Place the edge of the battery in the contacts first, then slide the battery back and down.
3. Place the rubber gasket back on the remote control.
Make sure the gasket is seated properly.
4. Place the back cover back on the top half of the remote control.
Place even pressure and listen for the halves to snap together.
TOYOTA RS3200 remote keyless Security system Page 1
INTRODUCTION Congratulations on your choice of the RS3200 remote keyless security system to protect your vehicle! To get the most from the system, we strongly recommend that you read this Owners Guide completely to learn all of its features and functions.
The RS3200 provides the convenience of remote keyless operation, enabling you to ARM and DISARM at the same time you remotely lock and unlock the doors. The system provides comprehen- sive security protection through point-of-entry monitoring, glass breakage detection and ignition switch monitoring. While ARMED, the system will be TRIGGERED and sound an ALARM when a door, trunk or hatch is forcibly unlocked or opened*, or when a window is tapped on or broken. During the ALARM, the vehicles horn sounds and the headlights, tail lights and front marker lights flash. A lso , the vehicles starter is disabled, to prevent engine start.
An important note about your system
Throughout this guide, there are references to the STATUS MONITOR for this system. Illustrated below, this panel holds the LED indicator (for the systems operating status) and the GLASS
BREAKAGE SENSORS microphone. In vehicles with an engine immobilizer, there is already a LED
installed in the vehicle, so the RS3200 utilizes the engine immobilizer system LED and a micro- phone mounted in a separate location. If your vehicle falls into this category, remember to look at that LED when the information refers to the STATUS MONITOR. If you do not know where the LED is located, refer to your vehicles owners guide for specific information.
About the ignition-controlled automatic door locking/unlocking function.
The RS3200 is programmed to automatically lock your vehicles doors when you turn the key in the ignition switch to the ON or START position, and unlock them when you turn the key back to the ACC or LOCK position. You may disable this feature by reprogramming the system; refer to page 18 for programming information.
* When the system is PASSIVELY (AUTOMATICALLY) ARMED, there is an ENTRY DELAY that will elapse when a door is opened before an ALARM is TRIGGERED.
YOUR ENGINE IMMOBILIZER
SYSTEM LED MAY LOOK
DIFFERENT THAN THE ONE
ILLUSTRATED HERE
LIGHTS FOR
30 SECONDS
(PRE-ARMING) THEN STARTS
FLASHING
(SYSTEM IS
ARMED)
Page 2 TOYOTA RS3200 REMOTE KEYLESS Security system TOYOTA RS3200 remote keyless Security system Page 19
REMOTE CONTROL BATTERY REPLACEMENT The following shows the procedure to replace the batteries in your remote controls. We recom- mend that you replace the batteries at least once a year, or when the remote controls transmitting range diminishes. You may obtain the replacement battery from your Toyota dealer, as well as many retailers that sell watch batteries. The battery replacement type is a Lithium CR2025.
Important notes on battery replacement: When replacing the battery, be careful not to lose the components. Take care not to bend or damage the rubber gasket.
REMOVE THE BATTERY
1. Lay the remote control on a towel or other soft material.
Place it with the back side facing up.
2. Using a coin, pry open the remote control.
Use gentle pressure to avoid deforming the plastic.
3. Set the back cover aside.
4. Remove the rubber gasket and set it aside.
5. Push the battery down and toward you, and hold it down.
6. Pry the back edge of the battery up and toward you.
REMOTE CONTROL INFORMATION THE REMOTE CONTROLS PROVIDED WITH YOUR SYSTEM
The 3 button remotes included with your system have separate LOCK and UNLOCK buttons on the front and a PANIC button on the back .
The RS3200 may be controlled by as many as 4 remote controls, so you may add two additional remote controls to the two included with your system. Contact your Toyota dealer for more details.
PROGRAMMING IGNITION-CONTROLLED AUTOMATIC DOOR LOCK/UNLOCK
The RS3200 is factory-set to automatically lock your vehicles doors when you turn the ignition key to ON or START, and unlock the doors when you turn the key back to ACC or LOCK. To change the programming of this feature, follow the procedure shown below.
1. Before you begin: Open the drivers door. Remove the key from the ignition switch.
2. Start the Programming Procedure. (Complete these steps within 30 seconds.)
Note: If the system does not activate the lights and buzzer, start over.
3. Select the Operating Mode and Complete the Programming Procedure.
Page 18 TOYOTA RS3200 REMOTE KEYLESS Security system TOYOTA RS3200 remote keyless Security system Page 3
Front Button
FLASHES WHEN BUTTONS PRESSED
PUSH TO LOCK DOORS AND ARM SYSTEM
PUSH TO UNLOCK DOORS AND DISARM SYSTEM
Back Button
HOLD TO ACTIVATE PANIC MODE OPERATION
NOTE: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful inter ference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accor dance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be deter mined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help.
a. Insert the key into the ignition switch and turn it from LOCK to ON 5 times (ending at ON).
c. The STATUS MONITORS LED (or the engine immobilizer systems LED) turns on for 30 seconds.
b. Turn the ignition key backto lock.
a. Close the door = IG. Controlled Door Locks ON Close, then open and close the door again = IG. Controlled Door Locks OFF
c. The tail and marker lights flash once and the buzzer chirps once when the system is set for IG door lock control ON, twice for IG door lock control OFF. If this does not happen, start over. Programming is now complete.
b. The tail and marker lights flash once, and the buzzer chirps once.
PROGRAMMING DRIVERS DOOR/ALL DOORS UNLOCK SELECTION (continued)
3. Select the Operating Mode and Complete the Programming Procedure.
Note: If the system locks the doors twice, start over.
Page 4 TOYOTA RS3200 REMOTE KEYLESS Security system TOYOTA RS3200 remote keyless Security system Page 17
FEATURES FUNCTIONS The RS3200 will ARM 30 seconds after the LOCK button on the remote control is pressed, and DISARM when the UNLOCK button is pressed. When the LOCK button is pressed, all the vehicles doors lock. When the UNLOCK button is pressed, the drivers door unlocks,* but if the UNLOCK button is pressed again within 3 seconds, the remaining doors unlock. The RS3200 will automatically RELOCK the vehicles doors if no door is opened within 60 seconds after REMOTE DISARMING, the system will
REARM 60 seconds later. The RS3200 will ARM 30 seconds after you close the trunk (if open) and lock the vehicles doors with the key, and will DISARM when you unlock a door with the key. While ARMED, the trunk may be opened with the key (or the AUX button on your remote control, if so equipped) without TRIGGERING an ALARM. Once the open trunk is closed, the system ARMS again. (See page 9 for more information.) The RS3200 may be programmed to automatically ARM 30 seconds after the ignition key is removed, the vehicle exited and the last door and the trunk closed, without the necessity of locking the doors. The RS3200 may be DISARMED with the vehicles ignition key after it was PASSIVELY ARMED. When the RS3200 has been PASSIVELY ARMED, an ENTRY DELAY (user- selectable at 0, 15, or 30 seconds) will start when a door is opened before an ALARM is TRIGGERED. When you lock the vehicle with a central lock switch (while a door is open), the RS3200 will ARM 30 seconds after you close all the doors and the trunk (if open). The RS3200 may be DISARMED by inserting the key into the ignition switch and turning it to ON. Forcibly unlocking or opening a door, hatch or trunk while the RS3200 is ARMED will TRIGGER an ALARM immediately. (If the system was PASSIVELY ARMED, the ENTRY DELAY must pass before the ALARM is TRIGGERED.) The RS3200 utilizes a microphone (usually mounted in the STATUS
MONITOR) to sense the noise from tapping on window glass, or glass breaking, and TRIGGER an ALARM. It is fine tuned to listen for this type of noise, and ignore other sounds. When the GLASS BREAKAGE SENSORS microphone picks up tapping or breaking of window glass, it TRIGGERS a WARN AWAY ALARM; the headlights and tail and marker lights flash, and the horn sounds for 20 seconds, but the starter is not disabled. If there is another detection of glass tapping or breaking, or if a door is opened or unlocked without a key, the regular ALARM is TRIGGERED. While ARMED, the RS3200 monitors the ignition switch. If an attempt is made to start the vehicle without a key, an ALARM is triggered.
** Starting from 2002 M.Y., Arming Suspension Mode by using the key to unlock the trunk is not applicable to Camry, Solara, and Corolla.
* You may program the system to unlock all the doors with one press on the UNLOCK button. See page 16 for programming instructions.
REMOTE ARMING/DISARMING & LOCKING/UNLOCKING
AUTOMATIC REARMING
KEY ARMING/DISARMING
ARMED MODE SUSPENSION **
PASSIVE (AUTOMATIC) ARMING
PASSIVE DISARMING
ADJUSTABLE ENTRY DELAY
MANUAL ARMING
IGNITION KEY DISARMING POINT-OF-ENTRY PROTECTION
GLASS BREAKAGE SENSOR
WARN AWAY ALARM
IGNITION SWITCH MONITORING
BRIEF DESCRIPTIONRS3200 FEATURES
a. Press and release both LOCK and UNLOCK buttons at the same time.
b. Press and release the UNLOCK button once for all doors unlock.
or Press and release the LOCK button once for drivers door unlock.
e. Open the drivers door; programming is now complete.
i. The tail and marker lights flash 1 time, the buzzer chirps 1 time, and the doors lock and unlock 1 time.
PROGRAMMING DRIVERS DOOR/ALL DOORS UNLOCK SELECTION
The RS3200 is factory-set to unlock the drivers door when the UNLOCK button is pressed on the remote control, then unlock the remaining doors when the UNLOCK button is pressed again within 3 seconds. You may change the programming so all doors will unlock at once when the UNLOCK button is pressed by fol- lowing the steps below.
1. Before you begin: 2. Start the Programming Procedure. Open the drivers door. (Complete these steps within 40 seconds.) Remove the key from the ignition switch.
Note: If the system does not activate the lights and buzzer, start over.
Page 16 TOYOTA RS3200 REMOTE KEYLESS Security system TOYOTA RS3200 remote keyless Security system Page 5
FEATURES FUNCTIONS When an ALARM is TRIGGERED, the system disables the vehicles starter and prevents engine start until the system is reset (DISARMED). During an ALARM, the system will lock the doors if one is unlocked, and will continue to do so for the duration of the ALARM. The user is notified that an ALARM occurred. Upon DISARMING the system after an ALARM was TRIGGERED, the vehicles tail and marker lights will be turned on, and the BUZZER sounds, for 2 seconds. You may TRIGGER a PANIC ALARM, by pressing the PANIC button on the back of the remote control, to draw attention to your vehicle. During the PANIC ALARM, the head, tail and marker lights flash, and the horn sounds, but the starter is not disabled. The RS3200 flashes the vehicles tail and marker lights during REMOTE ARMING and REMOTE DISARMING, as well as during an ALARM. Also, the headlights flash during an ALARM. When the system is REMOTE DISARMED, it turns on the interior lights in the vehicle for 30 seconds, or until the key is inserted into the ignition switch. It also turns them on during an ALARM. During an ALARM, the RS3200 activates the vehicles horn. If power to the RS3200 is disrupted while it is ARMED, an ALARM is TRIGGERED once power is restored. This panel houses the GLASS BREAKAGE SENSOR microphone and the flashing LED that indicates the operating status of the security system. (In vehicles with an engine immobilizer system, that systems LED and a separate microphone are used instead.) The RS3200 utilizes a PIEZO BUZZER, usually mounted in the engine compartment, to sound confirmation chirps and tones for function confirmation and programming step confirmation. The RS3200 automatically locks your vehicles doors when you turn the ignition key to ON or START, and unlocks the doors when you turn the key back to ACC or LOCK.* The Buzzer sounds for 5 seconds when you attempt to REMOTE ARM the system while a door is open. You can stop the warning by closing the door, or by pressing the UNLOCK button on the remote control. The maximum operating range for the remote controls included with the RS3200 is approximately 50 feet. Please refer to page 10 for a description of factors that may affect the performance (operating range) of the remote controls.
* You may disable this feature. Please refer to page 18 for programming information.
STARTER DISABLE
FORCED LOCK DURING ALARM TRIGGER MEMORY
PANIC MODE OPERATION
EXTERIOR LIGHT ACTIVATION
INTERIOR LIGHT ACTIVATION
HORN ACTIVATION POWER LOSS MEMORY
STATUS MONITOR
PIEZO BUZZER
IGNITION- CONTROLLED AUTOMATIC DOOR LOCK/UNLOCK DOOR AJAR WARNING
REMOTE CONTROL TRANSMITTER RANGE
BRIEF DESCRIPTIONRS3200 FEATURES
a. Insert the key into, and remove it from the ignition switch 2 times.
e. Insert the key into the ignition and leave it in.
c. Insert the key into, and remove it from the ignition switch 1 time.
g. Turn the key from LOCK to ON 4 times (ending at LOCK.)
h. Remove the key from the ignition switch.
b. Close, then open the drivers door 2 times.
f. Close the drivers door.
d. Close, then open the drivers door 2 times.
i. The tail and marker lights flash 4 times, the buzzer chirps 4 times, and the doors lock and unlock 4 times.
Page 6 TOYOTA RS3200 REMOTE KEYLESS Security system TOYOTA RS3200 remote keyless Security system Page 15
OPERATION ARMING THE RS3200 (except PASSIVE ARMING)
The system may be ARMED in several ways. Do one of the following:
Lock the doors with your key: Remove the key from the ignition switch. Exit the vehicle, and close all the doors.* Close the trunk or hatch, if necessary.* Insert the key into the door key switch and turn it toward the front of the vehicle:
The STATUS MONITORS LED turns on for 30 seconds, then starts flashing. The system is now ARMED.
Lock the doors from inside the vehicle: Remove the key from the ignition switch. Open the drivers or front passengers door. Push the central lock switch. Exit the vehicle, and close all the doors.* Close the trunk or hatch, if necessary.* Then:
The STATUS MONITORS LED turns on for 30 seconds, then starts flashing. The system is now ARMED.
Lock the doors with the remote control: Remove the key from the ignition switch. Exit the vehicle, and close all the doors.* Close the trunk or hatch, if necessary.* Press the LOCK button on the remote control. Simultaneously:
The doors lock. The vehicles tail and marker lights flash once. The buzzer chirps once. The STATUS MONITORS LED turns on for 30 seconds, then starts flashing. The system is now ARMED.
* The system will not ARM while any of the doors, trunk or hatch is open. However, when you press the LOCK button when the trunk is open, the doors will lock; the system will arm 30 seconds after the trunk is closed.
TURN TOWARD THE FRONT
OF THE VEHICLE
PRESS AND RELEASE
THE LOCK BUTTON
PUSH THE LOCK SWITCH WHILE
THE DOOR IS OPEN
LIGHTS FOR
30 SECONDS
(PRE-ARMING) THEN
FLASHES
(SYSTEM IS
ARMED)
THE TAIL AND MARKER LIGHTS FLASH ONCE
WHEN THE SYSTEM IS REMOTE ARMED
ALL DOORS LOCK WHEN THE
SYSTEM IS REMOTE ARMED
PROGRAMMING PASSIVE ARMING ON/OFF SELECTION, ENTRY DELAY TIME SELECTION
The RS3200 is factory-set to not PASSIVELY ARM. To change the systems operation for PASSIVE
ARMING operation, as well as adjust the ENTRY DELAY time, follow the procedure below. For more information on this feature, please refer to page 8.
1. Before you begin: Close all the doors, and the trunk or hatch. Unlock all the doors with the inside lock switch. Remove the key from the ignition switch.
2. Start the Programming Procedure. (Complete these steps within 30 seconds.)
3. Select the Operating Mode and Complete the Programming Procedure.
a. Using the remote control, lock, then unlock the doors 3 times.
b. Open the drivers door.
b. Lock then unlock the drivers door inside lock button 1 time.
a. Close, then Open the door: 2 times = PASSIVE ARMING OFF 3 times = PASSIVE ARMING ON,
0 Sec. ENTRY DELAY
4 times = PASSIVE ARMING ON, 15 Sec. ENTRY DELAY
5 times = PASSIVE ARMING ON, 30 Sec. ENTRY DELAY
c. Lock, then unlock the drivers door inside lock button 3 times.
d. The system locks the door in 2 seconds; if this does not happen, start over.
c. The system locks the door in 2 seconds; if this does not happen, start over. Programming is now complete.
e. Unlock the drivers door inside lock button.
THE BUZZER CHIRPS ONCE WHEN
THE SYSTEM IS REMOTE ARMED
Page 14 TOYOTA RS3200 REMOTE KEYLESS Security system TOYOTA RS3200 remote keyless Security system Page 7
OPERATION DISARMING THE RS3200 (except PASSIVE DISARMING)
The system may be DISARMED in several ways. Do one of the following:
Unlock the doors with your key: Insert the key into the door key switch and turn it toward the rear of the vehicle:
The STATUS MONITORS LED stops flashing. The system is now DISARMED.*
In the case of Sienna and 4Runner, you may also disarm the system using the key in the back door; all the doors will unlock at the same time. This feature is not available for Celica; you must disarm the system before opening the hatch, or else an ALARM will be Triggered.
Unlock the doors with the remote control: Press the UNLOCK button on the remote control. Simultaneously:
The drivers door unlocks. The vehicles tail and marker lights flash twice. The interior lights turn on for 30 seconds. The STATUS MONITORS LED stops flashing. The system is now DISARMED.*
Press the UNLOCK button again within 3 seconds after unlocking the drivers door to unlock the remaining doors.
Use the ignition switch: Insert the key into the ignition switch, then turn it to ON.
The STATUS MONITORS LED stops flashing. The system is now DISARMED.*
This method of disarming is rarely used. You must be inside the vehicle while the system is armed in order to do it.
NOTE: If your vehicles tail and marker lights turn on and the buzzer sounds for 2 seconds when the system is DISARMED, the TRIGGER MEMORY was activated; an ALARM was TRIGGERED while you were away from the vehicle.
* Please note, if the system utilizes your vehicles engine immobilizer system LED instead of the STATUS MONITOR, the LED will continue to flash.
TURN TOWARD THE REAR
OF THE VEHICLE
TURN THE KEY TO ON TO
DISARM THE SYSTEM
THE DRIVERS DOOR UNLOCKS
WHEN THE SYSTEM IS REMOTE
DISARMED
THE TAIL AND MARKER LIGHTS FLASH TWICE AND THE INTERIOR
LIGHTS TURN ON FOR 30 SECONDS WHEN THE SYSTEM IS
REMOTE DISARMED
PUSH THE UNLOCK BUTTON
STOPS
FLASHING
WHEN THE
SYSTEM IS
DISARMED
THE BUZZER CHIRPS TWICE WHEN THE SYSTEM IS
REMOTE DISARMED
GLASS BREAKAGE SENSOR INFORMATION The RS3200 provides protection for your vehicle above and beyond entry point monitoringit listens for the noise made by tapping on, or breaking of glass. Using a microphone designed specifically for this task, the GLASS BREAKAGE SENSOR is capable of ignoring other noises, which helps to prevent false alarms from occurring.
GLASS BREAKAGE SENSOR CHECK PROCEDURE
When the RS3200 was installed in your vehicle, care was taken to adjust the sensitivity level of the GLASS BREAKAGE SENSOR. You may observe how it works following the procedure listed below.
1. ARM the system. Press the LOCK button on the remote control or lock the doors with the key.
(Remember, the system will not ARM if any door, the trunk or hatch is open.)
2. Wait until the STATUS MONITORS LED starts flashing. The LED will flash 30 seconds after the last door, the trunk or hatch is closed.
3. With the tip of a key, tap the center of the drivers door window. Tap the glass with light to moderate force.
WARNING: Do not hit the glass with excessive force, especially in cold weather, or you may crack or break it.
A WARN AWAY ALARM should be TRIGGERED. If the ALARM is not TRIGGERED, make sure you performed the procedure correctly and try again. If you find that the system did not perform as expected, contact your Toyota dealer for more information.
4. DISARM the system to stop the WARN AWAY ALARM. Press the UNLOCK button on the remote control or use the key to DISARM the system.
Page 8 TOYOTA RS3200 REMOTE KEYLESS Security system TOYOTA RS3200 remote keyless Security system Page 13
OPERATION PASSIVE (AUTOMATIC) ARMING & DISARMING
When the RS3200 is programmed to PASSIVELY ARM, the system will ARM after the ignition key is removed and all doors and the trunk or hatch are closed; you do not need to lock the doors. When you come back to your vehicle and open a door, you must insert the key into the ignition switch and turn it to ON during the ENTRY DELAY (0, 15 or 30 seconds), or an ALARM will be TRIGGERED. If you lock the doors, regular ARMING will override PASSIVE ARMING; there will be no ENTRY DELAY. See the PROGRAMMING section on page 15 to activate the PASSIVE ARMING mode, as well as select the ENTRY DELAY time.
To PASSIVELY ARM the system: Remove the key from the ignition switch. Exit the vehicle, and close all the doors. (The system will not ARM
while any of the doors are open.) Close the trunk or hatch, if necessary. (The system will not ARM while the trunk or hatch is open.) After the last door, trunk or hatch is closed:
The STATUS MONITORS LED turns on for 30 seconds, then starts flashing. The system is now ARMED.
To DISARM the PASSIVELY ARMED system: Enter the vehicle through a front door. The ENTRY DELAY begins:
The STATUS MONITORS LED turns on (no flashing.) Insert the key into the ignition switch and turn it to ON before the ENTRY DELAY ends.*
The LED turns off. The system is now DISARMED.
You may also DISARM the system following any of the methods described on page 7.
NOTE: If your vehicles tail and marker lights turn on and the buzzer sounds for 2 seconds when the system is DISARMED, the TRIGGER MEMORY was activated; an ALARM was TRIGGERED while you were away from the vehicle.
* If the ENTRY DELAY time elapses before the ignition switch is turned to ON, an ALARM will be TRIGGERED. To DISARM the system during an ALARM, insert the ignition key and turn it to ON, or press and release the remote controls UNLOCK button.
THE SYSTEM ARMS 30 SECONDS
AFTER THE LAST ENTRY POINT
(DOOR, TRUNK OR HATCH) IS CLOSED
THE SYSTEM DISARMS WHEN
YOU INSERT THE KEY AND TURN IT
TO ON
LIGHTS FOR
30 SECONDS
(PRE-ARMING) THEN STARTS
FLASHING
(SYSTEM IS
ARMED)
TURNS ON
(NO
FLASHING) DURING THE
ENTRY DELAY
ALARM INFORMATION ALARM DESCRIPTIONS
Regular ALARM
When an ALARM is triggered in any way other than initial detection by the GLASS BREAKAGE SENSOR, the following occur:
The horn sounds repeatedly for 60 seconds. The headlights flash repeatedly for 60 seconds. The tail and marker lights flash repeatedly for 60 seconds. The interior lights turn on for 60 seconds. The starter is disabled (no engine start) until the system is DISARMED. The door lock will be relocked if someone reaches in and unlocks the inside lock button.
After 60 seconds of ALARM, the system will REARM and continue to protect the vehicle.
WARN-AWAY ALARM
Upon initial detection of noise from tapping on, or breaking glass, the GLASS BREAKAGE SENSOR
TRIGGERS a WARN AWAY ALARM: The horn sounds repeatedly for 20 seconds. The headlights flash repeatedly for 20 seconds. The tail and marker lights flash repeatedly for 20 seconds. The interior lights turn on for 20 seconds.
If the GLASS BREAKAGE SENSOR detects noise again, or if a door or trunk or hatch is opened while the system is still ARMED, the regular ALARM (described above) is activated.
STOPPING AN ALARM
Simply DISARM the system using the remote control or key as described on page 7.
THE HORN SOUNDS
FOR 20 SECONDS
HEADLIGHTS FLASH
FOR 20 SECONDS
MARKER LIGHTS
FLASH
FOR 20 SECONDS
TAIL LIGHTS FLASH
FOR 20 SECONDS
THE HORN SOUNDS
FOR 60 SECONDS
HEADLIGHTS FLASH
FOR 60 SECONDS
THE STARTER IS DISABLED UNTIL
THE SYSTEM IS DISARMED
MARKER LIGHTS
FLASH
FOR 60 SECONDS
TAIL LIGHTS FLASH
FOR 60 SECONDS
INTERIOR LIGHTS TURN ON FOR 60 SECONDS
INTERIOR LIGHTS TURN ON FOR 20 SECONDS
Page 12 TOYOTA RS3200 REMOTE KEYLESS Security system TOYOTA RS3200 remote keyless Security system Page 9
OPERATION AUTOMATIC REARMING
When you unlock the doors using the remote control, the RS3200 is DISARMED at the same time. However, if you do not open a door or the trunk or hatch within 30 seconds, the system will relock the doors and the RS3200 will REARM 30 seconds later
How the RS3200 automatically REARMS:
ARMING SUSPENSION **
The ARMED state of the RS3200 can be suspended temporarily by using the key to unlock and open the trunk. When the ARMING is suspended, the STATUS MONITORS LED will turn off until the trunk is closed again.
** Starting from 2002 M.Y., Arming Suspension Mode by using the key to unlock the trunk is not applicable to Camry, Solara, and Corolla.
0
15
30
45
THE DOORS ARE UNLOCKED
BY PRESSING THE UNLOCK
BUTTON ON THE REMOTE
CONTROL...
WHEN NO DOOR, TRUNK
OR HATCH IS OPENED... FOR MORE THAN 30
SECONDS... THE RS3200
AUTOMATICALLY RELOCKS
THE DOORS, THEN
AUTOMATICALLY REARMS.
THE LED LIGHTS UP
FOR 30 SECONDS
(PRE-ARM), THEN
FLASHES WHEN THE
SYSTEM IS ARMED
ALARM INFORMATION ALARM TRIGGERS
While the system is ARMED, an ALARM will be TRIGGERED when any of the following occurs:
Forcibly opening a door, or the trunk or hatch without a key
Pulling the trunk or hatch release lever inside the vehicle will also TRIGGER an ALARM.
Manually unlocking a door
Manually operating an inside lock button will TRIGGER an ALARM.
Note: Because this action will TRIGGER an ALARM, it is important that you do not ARM the system while someone is in the vehicle.
Hot wiring the vehicle
The RS3200 can detect the absence of the ignition key if the ignition circuit is shorted in attempt to start the vehicle.
Tapping on or breaking the glass
The noise from tapping on, or breaking of glass TRIGGERS a WARN
AWAY ALARM first, then a regular ALARM. See the description of how the GLASS BREAKAGE SENSOR TRIGGERS ALARMS on page 14.
Power restoration
If power to the system is interrupted while it is ARMED, an ALARM will be TRIGGERED immediately when power is restored.
TURNS OFF
WHEN THE
ARMED STATE
IS SUSPENDED
ALARM INFORMATION PANIC MODE OPERATION
When you are confronted by a threatening situation, you may call attention to your vehicle by pressing the PANIC button on the back of the remote control. Unless you DISARM the PANIC ALARM
by one of the described methods, it will continue for 60 seconds, then stop.
To activate the PANIC ALARM: Press the PANIC button on the back of the remote control. Simultaneously:
The horn sounds repeatedly for 60 seconds. The headlights flash repeatedly for 60 seconds. The tail and marker lights flash repeatedly for 60 seconds. The interior lights turn on for 60 seconds.
To disarm the Panic Alarm: Do one of the following shown below.
You may activate a PANIC ALARM at any time, except when the key is in the ignition switch and turned to the ON position. If the system detects an ALARM TRIGGER during the PANIC ALARM, the regular ALARM takes over. See ALARM INFORMATION on pages 12 and 13 for additional information.
Page 10 TOYOTA RS3200 REMOTE KEYLESS Security system TOYOTA RS3200 remote keyless Security system Page 11
MISCELLANEOUS DOOR AJAR WARNING
The RS3200 will sound a five second DOOR AJAR WARNING when you attempt to REMOTE ARM the system while a door is open. To stop the warning tone, either close the open door, or press and release the UNLOCK button on the remote control. To ARM the system, press the LOCK button again.
Note: The DOOR AJAR WARNING will not sound when the trunk is open; the doors will lock, but the system will not ARM until the trunk or hatch is closed.
IGNITION-CONTROLLED DOOR LOCKING/UNLOCKING
The RS3200 is programmed to automatically lock your vehicles doors when you turn the ignition key to ON or START, and unlock the doors when you turn the key back to ACC or LOCK. If you start the vehicle while a door is open, the system will not lock the doors; you must lock them manually.
How the RS3200 automatically locks and unlocks the doors:
This feature may be defeated by changing the systems programming. Refer to page 18 for programming instructions.
REMOTE CONTROL RANGE
The maximum range for the RS3200s remote controls is 50 feet. However, several factors that may affect your remote controls actual performance, include, but are not limited to:
The remote controls battery strength* (weak battery = decreased performance).
Your position relative to the vehicle (dependent on the systems antenna wire location).
Objects in the path between you and your vehicle.
Your surroundings (in a parking structure, out in the open, etc.).
Outside electrical interference caused by high tension power lines, etc.
* As the REMOTE CONTROLs battery becomes weaker, the LED indicator becomes dimmer. When you notice the LED becoming dimmer, you should replace the battery.
WITH ALL THE DOORS
CLOSED, TURN THE KEY TO
THE ON OR LOCK POSITION...
ALL THE DOORS ARE
LOCKED AUTOMATICALLY. PRESS THE
LOCK BUTTON
ON THE
REMOTE
CONTROL, OR...
PRESS THE
PANIC BUTTON
AGAIN, OR...
PRESS THE
UNLOCK
BUTTON ON
THE REMOTE
CONTROL, OR...
LOCK THE DOORS
WITH THE KEY, OR...
UNLOCK A DOOR OR THE TRUNK
WITH THE KEY WHEN THE KEY IS TURNED
BACK TO THE ACC OR
LOCK POSITION...
ALL THE DOORS ARE
UNLOCKED.
THE HORN SOUNDS
FOR 60 SECONDS
HEADLIGHTS FLASH
FOR 60 SECONDS
MARKER LIGHTS
FLASH
FOR 60 SECONDS
TAIL LIGHTS FLASH
FOR 60 SECONDS
INTERIOR LIGHTS TURN ON FOR 60 SECONDS
ALARM INFORMATION PANIC MODE OPERATION
When you are confronted by a threatening situation, you may call attention to your vehicle by pressing the PANIC button on the back of the remote control. Unless you DISARM the PANIC ALARM
by one of the described methods, it will continue for 60 seconds, then stop.
To activate the PANIC ALARM: Press the PANIC button on the back of the remote control. Simultaneously:
The horn sounds repeatedly for 60 seconds. The headlights flash repeatedly for 60 seconds. The tail and marker lights flash repeatedly for 60 seconds. The interior lights turn on for 60 seconds.
To disarm the Panic Alarm: Do one of the following shown below.
You may activate a PANIC ALARM at any time, except when the key is in the ignition switch and turned to the ON position. If the system detects an ALARM TRIGGER during the PANIC ALARM, the regular ALARM takes over. See ALARM INFORMATION on pages 12 and 13 for additional information.
Page 10 TOYOTA RS3200 REMOTE KEYLESS Security system TOYOTA RS3200 remote keyless Security system Page 11
MISCELLANEOUS DOOR AJAR WARNING
The RS3200 will sound a five second DOOR AJAR WARNING when you attempt to REMOTE ARM the system while a door is open. To stop the warning tone, either close the open door, or press and release the UNLOCK button on the remote control. To ARM the system, press the LOCK button again.
Note: The DOOR AJAR WARNING will not sound when the trunk is open; the doors will lock, but the system will not ARM until the trunk or hatch is closed.
IGNITION-CONTROLLED DOOR LOCKING/UNLOCKING
The RS3200 is programmed to automatically lock your vehicles doors when you turn the ignition key to ON or START, and unlock the doors when you turn the key back to ACC or LOCK. If you start the vehicle while a door is open, the system will not lock the doors; you must lock them manually.
How the RS3200 automatically locks and unlocks the doors:
This feature may be defeated by changing the systems programming. Refer to page 18 for programming instructions.
REMOTE CONTROL RANGE
The maximum range for the RS3200s remote controls is 50 feet. However, several factors that may affect your remote controls actual performance, include, but are not limited to:
The remote controls battery strength* (weak battery = decreased performance).
Your position relative to the vehicle (dependent on the systems antenna wire location).
Objects in the path between you and your vehicle.
Your surroundings (in a parking structure, out in the open, etc.).
Outside electrical interference caused by high tension power lines, etc.
* As the REMOTE CONTROLs battery becomes weaker, the LED indicator becomes dimmer. When you notice the LED becoming dimmer, you should replace the battery.
WITH ALL THE DOORS
CLOSED, TURN THE KEY TO
THE ON OR LOCK POSITION...
ALL THE DOORS ARE
LOCKED AUTOMATICALLY. PRESS THE
LOCK BUTTON
ON THE
REMOTE
CONTROL, OR...
PRESS THE
PANIC BUTTON
AGAIN, OR...
PRESS THE
UNLOCK
BUTTON ON
THE REMOTE
CONTROL, OR...
LOCK THE DOORS
WITH THE KEY, OR...
UNLOCK A DOOR OR THE TRUNK
WITH THE KEY WHEN THE KEY IS TURNED
BACK TO THE ACC OR
LOCK POSITION...
ALL THE DOORS ARE
UNLOCKED.
THE HORN SOUNDS
FOR 60 SECONDS
HEADLIGHTS FLASH
FOR 60 SECONDS
MARKER LIGHTS
FLASH
FOR 60 SECONDS
TAIL LIGHTS FLASH
FOR 60 SECONDS
INTERIOR LIGHTS TURN ON FOR 60 SECONDS
Page 12 TOYOTA RS3200 REMOTE KEYLESS Security system TOYOTA RS3200 remote keyless Security system Page 9
OPERATION AUTOMATIC REARMING
When you unlock the doors using the remote control, the RS3200 is DISARMED at the same time. However, if you do not open a door or the trunk or hatch within 30 seconds, the system will relock the doors and the RS3200 will REARM 30 seconds later
How the RS3200 automatically REARMS:
ARMING SUSPENSION **
The ARMED state of the RS3200 can be suspended temporarily by using the key to unlock and open the trunk. When the ARMING is suspended, the STATUS MONITORS LED will turn off until the trunk is closed again.
** Starting from 2002 M.Y., Arming Suspension Mode by using the key to unlock the trunk is not applicable to Camry, Solara, and Corolla.
0
15
30
45
THE DOORS ARE UNLOCKED
BY PRESSING THE UNLOCK
BUTTON ON THE REMOTE
CONTROL...
WHEN NO DOOR, TRUNK
OR HATCH IS OPENED... FOR MORE THAN 30
SECONDS... THE RS3200
AUTOMATICALLY RELOCKS
THE DOORS, THEN
AUTOMATICALLY REARMS.
THE LED LIGHTS UP
FOR 30 SECONDS
(PRE-ARM), THEN
FLASHES WHEN THE
SYSTEM IS ARMED
ALARM INFORMATION ALARM TRIGGERS
While the system is ARMED, an ALARM will be TRIGGERED when any of the following occurs:
Forcibly opening a door, or the trunk or hatch without a key
Pulling the trunk or hatch release lever inside the vehicle will also TRIGGER an ALARM.
Manually unlocking a door
Manually operating an inside lock button will TRIGGER an ALARM.
Note: Because this action will TRIGGER an ALARM, it is important that you do not ARM the system while someone is in the vehicle.
Hot wiring the vehicle
The RS3200 can detect the absence of the ignition key if the ignition circuit is shorted in attempt to start the vehicle.
Tapping on or breaking the glass
The noise from tapping on, or breaking of glass TRIGGERS a WARN
AWAY ALARM first, then a regular ALARM. See the description of how the GLASS BREAKAGE SENSOR TRIGGERS ALARMS on page 14.
Power restoration
If power to the system is interrupted while it is ARMED, an ALARM will be TRIGGERED immediately when power is restored.
TURNS OFF
WHEN THE
ARMED STATE
IS SUSPENDED
Page 8 TOYOTA RS3200 REMOTE KEYLESS Security system TOYOTA RS3200 remote keyless Security system Page 13
OPERATION PASSIVE (AUTOMATIC) ARMING & DISARMING
When the RS3200 is programmed to PASSIVELY ARM, the system will ARM after the ignition key is removed and all doors and the trunk or hatch are closed; you do not need to lock the doors. When you come back to your vehicle and open a door, you must insert the key into the ignition switch and turn it to ON during the ENTRY DELAY (0, 15 or 30 seconds), or an ALARM will be TRIGGERED. If you lock the doors, regular ARMING will override PASSIVE ARMING; there will be no ENTRY DELAY. See the PROGRAMMING section on page 15 to activate the PASSIVE ARMING mode, as well as select the ENTRY DELAY time.
To PASSIVELY ARM the system: Remove the key from the ignition switch. Exit the vehicle, and close all the doors. (The system will not ARM
while any of the doors are open.) Close the trunk or hatch, if necessary. (The system will not ARM while the trunk or hatch is open.) After the last door, trunk or hatch is closed:
The STATUS MONITORS LED turns on for 30 seconds, then starts flashing. The system is now ARMED.
To DISARM the PASSIVELY ARMED system: Enter the vehicle through a front door. The ENTRY DELAY begins:
The STATUS MONITORS LED turns on (no flashing.) Insert the key into the ignition switch and turn it to ON before the ENTRY DELAY ends.*
The LED turns off. The system is now DISARMED.
You may also DISARM the system following any of the methods described on page 7.
NOTE: If your vehicles tail and marker lights turn on and the buzzer sounds for 2 seconds when the system is DISARMED, the TRIGGER MEMORY was activated; an ALARM was TRIGGERED while you were away from the vehicle.
* If the ENTRY DELAY time elapses before the ignition switch is turned to ON, an ALARM will be TRIGGERED. To DISARM the system during an ALARM, insert the ignition key and turn it to ON, or press and release the remote controls UNLOCK button.
THE SYSTEM ARMS 30 SECONDS
AFTER THE LAST ENTRY POINT
(DOOR, TRUNK OR HATCH) IS CLOSED
THE SYSTEM DISARMS WHEN
YOU INSERT THE KEY AND TURN IT
TO ON
LIGHTS FOR
30 SECONDS
(PRE-ARMING) THEN STARTS
FLASHING
(SYSTEM IS
ARMED)
TURNS ON
(NO
FLASHING) DURING THE
ENTRY DELAY
ALARM INFORMATION ALARM DESCRIPTIONS
Regular ALARM
When an ALARM is triggered in any way other than initial detection by the GLASS BREAKAGE SENSOR, the following occur:
The horn sounds repeatedly for 60 seconds. The headlights flash repeatedly for 60 seconds. The tail and marker lights flash repeatedly for 60 seconds. The interior lights turn on for 60 seconds. The starter is disabled (no engine start) until the system is DISARMED. The door lock will be relocked if someone reaches in and unlocks the inside lock button.
After 60 seconds of ALARM, the system will REARM and continue to protect the vehicle.
WARN-AWAY ALARM
Upon initial detection of noise from tapping on, or breaking glass, the GLASS BREAKAGE SENSOR
TRIGGERS a WARN AWAY ALARM: The horn sounds repeatedly for 20 seconds. The headlights flash repeatedly for 20 seconds. The tail and marker lights flash repeatedly for 20 seconds. The interior lights turn on for 20 seconds.
If the GLASS BREAKAGE SENSOR detects noise again, or if a door or trunk or hatch is opened while the system is still ARMED, the regular ALARM (described above) is activated.
STOPPING AN ALARM
Simply DISARM the system using the remote control or key as described on page 7.
THE HORN SOUNDS
FOR 20 SECONDS
HEADLIGHTS FLASH
FOR 20 SECONDS
MARKER LIGHTS
FLASH
FOR 20 SECONDS
TAIL LIGHTS FLASH
FOR 20 SECONDS
THE HORN SOUNDS
FOR 60 SECONDS
HEADLIGHTS FLASH
FOR 60 SECONDS
THE STARTER IS DISABLED UNTIL
THE SYSTEM IS DISARMED
MARKER LIGHTS
FLASH
FOR 60 SECONDS
TAIL LIGHTS FLASH
FOR 60 SECONDS
INTERIOR LIGHTS TURN ON FOR 60 SECONDS
INTERIOR LIGHTS TURN ON FOR 20 SECONDS
Page 14 TOYOTA RS3200 REMOTE KEYLESS Security system TOYOTA RS3200 remote keyless Security system Page 7
OPERATION DISARMING THE RS3200 (except PASSIVE DISARMING)
The system may be DISARMED in several ways. Do one of the following:
Unlock the doors with your key: Insert the key into the door key switch and turn it toward the rear of the vehicle:
The STATUS MONITORS LED stops flashing. The system is now DISARMED.*
In the case of Sienna and 4Runner, you may also disarm the system using the key in the back door; all the doors will unlock at the same time. This feature is not available for Celica; you must disarm the system before opening the hatch, or else an ALARM will be Triggered.
Unlock the doors with the remote control: Press the UNLOCK button on the remote control. Simultaneously:
The drivers door unlocks. The vehicles tail and marker lights flash twice. The interior lights turn on for 30 seconds. The STATUS MONITORS LED stops flashing. The system is now DISARMED.*
Press the UNLOCK button again within 3 seconds after unlocking the drivers door to unlock the remaining doors.
Use the ignition switch: Insert the key into the ignition switch, then turn it to ON.
The STATUS MONITORS LED stops flashing. The system is now DISARMED.*
This method of disarming is rarely used. You must be inside the vehicle while the system is armed in order to do it.
NOTE: If your vehicles tail and marker lights turn on and the buzzer sounds for 2 seconds when the system is DISARMED, the TRIGGER MEMORY was activated; an ALARM was TRIGGERED while you were away from the vehicle.
* Please note, if the system utilizes your vehicles engine immobilizer system LED instead of the STATUS MONITOR, the LED will continue to flash.
TURN TOWARD THE REAR
OF THE VEHICLE
TURN THE KEY TO ON TO
DISARM THE SYSTEM
THE DRIVERS DOOR UNLOCKS
WHEN THE SYSTEM IS REMOTE
DISARMED
THE TAIL AND MARKER LIGHTS FLASH TWICE AND THE INTERIOR
LIGHTS TURN ON FOR 30 SECONDS WHEN THE SYSTEM IS
REMOTE DISARMED
PUSH THE UNLOCK BUTTON
STOPS
FLASHING
WHEN THE
SYSTEM IS
DISARMED
THE BUZZER CHIRPS TWICE WHEN THE SYSTEM IS
REMOTE DISARMED
GLASS BREAKAGE SENSOR INFORMATION The RS3200 provides protection for your vehicle above and beyond entry point monitoringit listens for the noise made by tapping on, or breaking of glass. Using a microphone designed specifically for this task, the GLASS BREAKAGE SENSOR is capable of ignoring other noises, which helps to prevent false alarms from occurring.
GLASS BREAKAGE SENSOR CHECK PROCEDURE
When the RS3200 was installed in your vehicle, care was taken to adjust the sensitivity level of the GLASS BREAKAGE SENSOR. You may observe how it works following the procedure listed below.
1. ARM the system. Press the LOCK button on the remote control or lock the doors with the key.
(Remember, the system will not ARM if any door, the trunk or hatch is open.)
2. Wait until the STATUS MONITORS LED starts flashing. The LED will flash 30 seconds after the last door, the trunk or hatch is closed.
3. With the tip of a key, tap the center of the drivers door window. Tap the glass with light to moderate force.
WARNING: Do not hit the glass with excessive force, especially in cold weather, or you may crack or break it.
A WARN AWAY ALARM should be TRIGGERED. If the ALARM is not TRIGGERED, make sure you performed the procedure correctly and try again. If you find that the system did not perform as expected, contact your Toyota dealer for more information.
4. DISARM the system to stop the WARN AWAY ALARM. Press the UNLOCK button on the remote control or use the key to DISARM the system.
Page 6 TOYOTA RS3200 REMOTE KEYLESS Security system TOYOTA RS3200 remote keyless Security system Page 15
OPERATION ARMING THE RS3200 (except PASSIVE ARMING)
The system may be ARMED in several ways. Do one of the following:
Lock the doors with your key: Remove the key from the ignition switch. Exit the vehicle, and close all the doors.* Close the trunk or hatch, if necessary.* Insert the key into the door key switch and turn it toward the front of the vehicle:
The STATUS MONITORS LED turns on for 30 seconds, then starts flashing. The system is now ARMED.
Lock the doors from inside the vehicle: Remove the key from the ignition switch. Open the drivers or front passengers door. Push the central lock switch. Exit the vehicle, and close all the doors.* Close the trunk or hatch, if necessary.* Then:
The STATUS MONITORS LED turns on for 30 seconds, then starts flashing. The system is now ARMED.
Lock the doors with the remote control: Remove the key from the ignition switch. Exit the vehicle, and close all the doors.* Close the trunk or hatch, if necessary.* Press the LOCK button on the remote control. Simultaneously:
The doors lock. The vehicles tail and marker lights flash once. The buzzer chirps once. The STATUS MONITORS LED turns on for 30 seconds, then starts flashing. The system is now ARMED.
* The system will not ARM while any of the doors, trunk or hatch is open. However, when you press the LOCK button when the trunk is open, the doors will lock; the system will arm 30 seconds after the trunk is closed.
TURN TOWARD THE FRONT
OF THE VEHICLE
PRESS AND RELEASE
THE LOCK BUTTON
PUSH THE LOCK SWITCH WHILE
THE DOOR IS OPEN
LIGHTS FOR
30 SECONDS
(PRE-ARMING) THEN
FLASHES
(SYSTEM IS
ARMED)
THE TAIL AND MARKER LIGHTS FLASH ONCE
WHEN THE SYSTEM IS REMOTE ARMED
ALL DOORS LOCK WHEN THE
SYSTEM IS REMOTE ARMED
PROGRAMMING PASSIVE ARMING ON/OFF SELECTION, ENTRY DELAY TIME SELECTION
The RS3200 is factory-set to not PASSIVELY ARM. To change the systems operation for PASSIVE
ARMING operation, as well as adjust the ENTRY DELAY time, follow the procedure below. For more information on this feature, please refer to page 8.
1. Before you begin: Close all the doors, and the trunk or hatch. Unlock all the doors with the inside lock switch. Remove the key from the ignition switch.
2. Start the Programming Procedure. (Complete these steps within 30 seconds.)
3. Select the Operating Mode and Complete the Programming Procedure.
a. Using the remote control, lock, then unlock the doors 3 times.
b. Open the drivers door.
b. Lock then unlock the drivers door inside lock button 1 time.
a. Close, then Open the door: 2 times = PASSIVE ARMING OFF 3 times = PASSIVE ARMING ON,
0 Sec. ENTRY DELAY
4 times = PASSIVE ARMING ON, 15 Sec. ENTRY DELAY
5 times = PASSIVE ARMING ON, 30 Sec. ENTRY DELAY
c. Lock, then unlock the drivers door inside lock button 3 times.
d. The system locks the door in 2 seconds; if this does not happen, start over.
c. The system locks the door in 2 seconds; if this does not happen, start over. Programming is now complete.
e. Unlock the drivers door inside lock button.
THE BUZZER CHIRPS ONCE WHEN
THE SYSTEM IS REMOTE ARMED
PROGRAMMING DRIVERS DOOR/ALL DOORS UNLOCK SELECTION
The RS3200 is factory-set to unlock the drivers door when the UNLOCK button is pressed on the remote control, then unlock the remaining doors when the UNLOCK button is pressed again within 3 seconds. You may change the programming so all doors will unlock at once when the UNLOCK button is pressed by fol- lowing the steps below.
1. Before you begin: 2. Start the Programming Procedure. Open the drivers door. (Complete these steps within 40 seconds.) Remove the key from the ignition switch.
Note: If the system does not activate the lights and buzzer, start over.
Page 16 TOYOTA RS3200 REMOTE KEYLESS Security system TOYOTA RS3200 remote keyless Security system Page 5
FEATURES FUNCTIONS When an ALARM is TRIGGERED, the system disables the vehicles starter and prevents engine start until the system is reset (DISARMED). During an ALARM, the system will lock the doors if one is unlocked, and will continue to do so for the duration of the ALARM. The user is notified that an ALARM occurred. Upon DISARMING the system after an ALARM was TRIGGERED, the vehicles tail and marker lights will be turned on, and the BUZZER sounds, for 2 seconds. You may TRIGGER a PANIC ALARM, by pressing the PANIC button on the back of the remote control, to draw attention to your vehicle. During the PANIC ALARM, the head, tail and marker lights flash, and the horn sounds, but the starter is not disabled. The RS3200 flashes the vehicles tail and marker lights during REMOTE ARMING and REMOTE DISARMING, as well as during an ALARM. Also, the headlights flash during an ALARM. When the system is REMOTE DISARMED, it turns on the interior lights in the vehicle for 30 seconds, or until the key is inserted into the ignition switch. It also turns them on during an ALARM. During an ALARM, the RS3200 activates the vehicles horn. If power to the RS3200 is disrupted while it is ARMED, an ALARM is TRIGGERED once power is restored. This panel houses the GLASS BREAKAGE SENSOR microphone and the flashing LED that indicates the operating status of the security system. (In vehicles with an engine immobilizer system, that systems LED and a separate microphone are used instead.) The RS3200 utilizes a PIEZO BUZZER, usually mounted in the engine compartment, to sound confirmation chirps and tones for function confirmation and programming step confirmation. The RS3200 automatically locks your vehicles doors when you turn the ignition key to ON or START, and unlocks the doors when you turn the key back to ACC or LOCK.* The Buzzer sounds for 5 seconds when you attempt to REMOTE ARM the system while a door is open. You can stop the warning by closing the door, or by pressing the UNLOCK button on the remote control. The maximum operating range for the remote controls included with the RS3200 is approximately 50 feet. Please refer to page 10 for a description of factors that may affect the performance (operating range) of the remote controls.
* You may disable this feature. Please refer to page 18 for programming information.
STARTER DISABLE
FORCED LOCK DURING ALARM TRIGGER MEMORY
PANIC MODE OPERATION
EXTERIOR LIGHT ACTIVATION
INTERIOR LIGHT ACTIVATION
HORN ACTIVATION POWER LOSS MEMORY
STATUS MONITOR
PIEZO BUZZER
IGNITION- CONTROLLED AUTOMATIC DOOR LOCK/UNLOCK DOOR AJAR WARNING
REMOTE CONTROL TRANSMITTER RANGE
BRIEF DESCRIPTIONRS3200 FEATURES
a. Insert the key into, and remove it from the ignition switch 2 times.
e. Insert the key into the ignition and leave it in.
c. Insert the key into, and remove it from the ignition switch 1 time.
g. Turn the key from LOCK to ON 4 times (ending at LOCK.)
h. Remove the key from the ignition switch.
b. Close, then open the drivers door 2 times.
f. Close the drivers door.
d. Close, then open the drivers door 2 times.
i. The tail and marker lights flash 4 times, the buzzer chirps 4 times, and the doors lock and unlock 4 times.
PROGRAMMING DRIVERS DOOR/ALL DOORS UNLOCK SELECTION (continued)
3. Select the Operating Mode and Complete the Programming Procedure.
Note: If the system locks the doors twice, start over.
Page 4 TOYOTA RS3200 REMOTE KEYLESS Security system TOYOTA RS3200 remote keyless Security system Page 17
FEATURES FUNCTIONS The RS3200 will ARM 30 seconds after the LOCK button on the remote control is pressed, and DISARM when the UNLOCK button is pressed. When the LOCK button is pressed, all the vehicles doors lock. When the UNLOCK button is pressed, the drivers door unlocks,* but if the UNLOCK button is pressed again within 3 seconds, the remaining doors unlock. The RS3200 will automatically RELOCK the vehicles doors if no door is opened within 60 seconds after REMOTE DISARMING, the system will
REARM 60 seconds later. The RS3200 will ARM 30 seconds after you close the trunk (if open) and lock the vehicles doors with the key, and will DISARM when you unlock a door with the key. While ARMED, the trunk may be opened with the key (or the AUX button on your remote control, if so equipped) without TRIGGERING an ALARM. Once the open trunk is closed, the system ARMS again. (See page 9 for more information.) The RS3200 may be programmed to automatically ARM 30 seconds after the ignition key is removed, the vehicle exited and the last door and the trunk closed, without the necessity of locking the doors. The RS3200 may be DISARMED with the vehicles ignition key after it was PASSIVELY ARMED. When the RS3200 has been PASSIVELY ARMED, an ENTRY DELAY (user- selectable at 0, 15, or 30 seconds) will start when a door is opened before an ALARM is TRIGGERED. When you lock the vehicle with a central lock switch (while a door is open), the RS3200 will ARM 30 seconds after you close all the doors and the trunk (if open). The RS3200 may be DISARMED by inserting the key into the ignition switch and turning it to ON. Forcibly unlocking or opening a door, hatch or trunk while the RS3200 is ARMED will TRIGGER an ALARM immediately. (If the system was PASSIVELY ARMED, the ENTRY DELAY must pass before the ALARM is TRIGGERED.) The RS3200 utilizes a microphone (usually mounted in the STATUS
MONITOR) to sense the noise from tapping on window glass, or glass breaking, and TRIGGER an ALARM. It is fine tuned to listen for this type of noise, and ignore other sounds. When the GLASS BREAKAGE SENSORS microphone picks up tapping or breaking of window glass, it TRIGGERS a WARN AWAY ALARM; the headlights and tail and marker lights flash, and the horn sounds for 20 seconds, but the starter is not disabled. If there is another detection of glass tapping or breaking, or if a door is opened or unlocked without a key, the regular ALARM is TRIGGERED. While ARMED, the RS3200 monitors the ignition switch. If an attempt is made to start the vehicle without a key, an ALARM is triggered.
** Starting from 2002 M.Y., Arming Suspension Mode by using the key to unlock the trunk is not applicable to Camry, Solara, and Corolla.
* You may program the system to unlock all the doors with one press on the UNLOCK button. See page 16 for programming instructions.
REMOTE ARMING/DISARMING & LOCKING/UNLOCKING
AUTOMATIC REARMING
KEY ARMING/DISARMING
ARMED MODE SUSPENSION **
PASSIVE (AUTOMATIC) ARMING
PASSIVE DISARMING
ADJUSTABLE ENTRY DELAY
MANUAL ARMING
IGNITION KEY DISARMING POINT-OF-ENTRY PROTECTION
GLASS BREAKAGE SENSOR
WARN AWAY ALARM
IGNITION SWITCH MONITORING
BRIEF DESCRIPTIONRS3200 FEATURES
a. Press and release both LOCK and UNLOCK buttons at the same time.
b. Press and release the UNLOCK button once for all doors unlock.
or Press and release the LOCK button once for drivers door unlock.
e. Open the drivers door; programming is now complete.
i. The tail and marker lights flash 1 time, the buzzer chirps 1 time, and the doors lock and unlock 1 time.
REMOTE CONTROL INFORMATION THE REMOTE CONTROLS PROVIDED WITH YOUR SYSTEM
The 3 button remotes included with your system have separate LOCK and UNLOCK buttons on the front and a PANIC button on the back .
The RS3200 may be controlled by as many as 4 remote controls, so you may add two additional remote controls to the two included with your system. Contact your Toyota dealer for more details.
PROGRAMMING IGNITION-CONTROLLED AUTOMATIC DOOR LOCK/UNLOCK
The RS3200 is factory-set to automatically lock your vehicles doors when you turn the ignition key to ON or START, and unlock the doors when you turn the key back to ACC or LOCK. To change the programming of this feature, follow the procedure shown below.
1. Before you begin: Open the drivers door. Remove the key from the ignition switch.
2. Start the Programming Procedure. (Complete these steps within 30 seconds.)
Note: If the system does not activate the lights and buzzer, start over.
3. Select the Operating Mode and Complete the Programming Procedure.
Page 18 TOYOTA RS3200 REMOTE KEYLESS Security system TOYOTA RS3200 remote keyless Security system Page 3
Front Button
FLASHES WHEN BUTTONS PRESSED
PUSH TO LOCK DOORS AND ARM SYSTEM
PUSH TO UNLOCK DOORS AND DISARM SYSTEM
Back Button
HOLD TO ACTIVATE PANIC MODE OPERATION
NOTE: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful inter ference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accor dance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be deter mined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help.
a. Insert the key into the ignition switch and turn it from LOCK to ON 5 times (ending at ON).
c. The STATUS MONITORS LED (or the engine immobilizer systems LED) turns on for 30 seconds.
b. Turn the ignition key backto lock.
a. Close the door = IG. Controlled Door Locks ON Close, then open and close the door again = IG. Controlled Door Locks OFF
c. The tail and marker lights flash once and the buzzer chirps once when the system is set for IG door lock control ON, twice for IG door lock control OFF. If this does not happen, start over. Programming is now complete.
b. The tail and marker lights flash once, and the buzzer chirps once.
INTRODUCTION Congratulations on your choice of the RS3200 remote keyless security system to protect your vehicle! To get the most from the system, we strongly recommend that you read this Owners Guide completely to learn all of its features and functions.
The RS3200 provides the convenience of remote keyless operation, enabling you to ARM and DISARM at the same time you remotely lock and unlock the doors. The system provides comprehen- sive security protection through point-of-entry monitoring, glass breakage detection and ignition switch monitoring. While ARMED, the system will be TRIGGERED and sound an ALARM when a door, trunk or hatch is forcibly unlocked or opened*, or when a window is tapped on or broken. During the ALARM, the vehicles horn sounds and the headlights, tail lights and front marker lights flash. A lso , the vehicles starter is disabled, to prevent engine start.
An important note about your system
Throughout this guide, there are references to the STATUS MONITOR for this system. Illustrated below, this panel holds the LED indicator (for the systems operating status) and the GLASS
BREAKAGE SENSORS microphone. In vehicles with an engine immobilizer, there is already a LED
installed in the vehicle, so the RS3200 utilizes the engine immobilizer system LED and a micro- phone mounted in a separate location. If your vehicle falls into this category, remember to look at that LED when the information refers to the STATUS MONITOR. If you do not know where the LED is located, refer to your vehicles owners guide for specific information.
About the ignition-controlled automatic door locking/unlocking function.
The RS3200 is programmed to automatically lock your vehicles doors when you turn the key in the ignition switch to the ON or START position, and unlock them when you turn the key back to the ACC or LOCK position. You may disable this feature by reprogramming the system; refer to page 18 for programming information.
* When the system is PASSIVELY (AUTOMATICALLY) ARMED, there is an ENTRY DELAY that will elapse when a door is opened before an ALARM is TRIGGERED.
YOUR ENGINE IMMOBILIZER
SYSTEM LED MAY LOOK
DIFFERENT THAN THE ONE
ILLUSTRATED HERE
LIGHTS FOR
30 SECONDS
(PRE-ARMING) THEN STARTS
FLASHING
(SYSTEM IS
ARMED)
Page 2 TOYOTA RS3200 REMOTE KEYLESS Security system TOYOTA RS3200 remote keyless Security system Page 19
REMOTE CONTROL BATTERY REPLACEMENT The following shows the procedure to replace the batteries in your remote controls. We recom- mend that you replace the batteries at least once a year, or when the remote controls transmitting range diminishes. You may obtain the replacement battery from your Toyota dealer, as well as many retailers that sell watch batteries. The battery replacement type is a Lithium CR2025.
Important notes on battery replacement: When replacing the battery, be careful not to lose the components. Take care not to bend or damage the rubber gasket.
REMOVE THE BATTERY
1. Lay the remote control on a towel or other soft material.
Place it with the back side facing up.
2. Using a coin, pry open the remote control.
Use gentle pressure to avoid deforming the plastic.
3. Set the back cover aside.
4. Remove the rubber gasket and set it aside.
5. Push the battery down and toward you, and hold it down.
6. Pry the back edge of the battery up and toward you.
Page 20 TOYOTA RS3200 REMOTE KEYLESS Security system
To better understand the features and functions of this security system, please read this Owners Guide completely prior to use.
TABLE OF CONTENTS
DESCRIPTION PAGE INTRODUCTION 2
REMOTE CONTROL INFORMATION THE REMOTE CONTROL INCLUDED WITH YOUR SYSTEM 3
BRIEF DESCRIPTIONRS3200 FEATURES 4, 5
OPERATION ARMING THE RS3200 (except PASSIVE ARMING) 6 DISARMING THE RS3200 (except PASSIVE DISARMING) 7 PASSIVE (AUTOMATIC) ARMING & DISARMING 8 AUTOMATIC REARMING 9 ARMING SUSPENSION 9
MISCELLANEOUS DOOR AJAR WARNING 10 IGNITION-CONTROLLED DOOR LOCKING/UNLOCKING 10 REMOTE CONTROL RANGE 10
ALARM INFORMATION PANIC MODE OPERATION 11 ALARM TRIGGERS 12 ALARM DESCRIPTIONS 13 STOPPING AN ALARM 13
GLASS BREAKAGE SENSOR INFORMATION GLASS BREAKAGE SENSOR CHECK PROCEDURE 14
PROGRAMMING PASSIVE (AUTOMATIC) ARMING AND ENTRY DELAY 15 DRIVERS DOOR/ALL DOORS UNLOCK SELECTION 16, 17 IGNITION-CONTROLLED DOOR LOCKING/UNLOCKING 18
REMOTE CONTROL BATTERY REPLACEMENT REMOVE THE BATTERY 19 INSTALL THE BATTERY 20
WARNING AND CAUTION INFORMATION 21
REMOTE CONTROL BATTERY REPLACEMENT INSTALL THE BATTERY
1. Hold the battery with the plus side up.
Handle the battery with a cloth or tissue; body oils and moisture can interfere with operation and may reduce the life of the battery.
2. Insert the new battery as shown.
Place the edge of the battery in the contacts first, then slide the battery back and down.
3. Place the rubber gasket back on the remote control.
Make sure the gasket is seated properly.
4. Place the back cover back on the top half of the remote control.
Place even pressure and listen for the halves to snap together.
TOYOTA RS3200 remote keyless Security system Page 1
TOYOTA RS3200 remote keyless Security system Page 21
Warning This product is applicable only to vehicles with 12V DC, negative grounding specifications. Do
not use in vehicles with 24V specifications. Otherwise, damage to the unit or a fire may result.
To prevent accidents from occurring, keep the remote controls batteries out of the reach of children. In the event a battery is swallowed, consult a physician immediately.
Never attempt to disassemble or modify the product. Otherwise, an accident, fire or electric shock may result.
When replacing fuses, be sure to use fuses with the same specified capacity (amperage.) Otherwise, damage to the unit or vehicle, fire or electric shock may result.
If an abnormal condition occurs, such as liquids spilling onto the product, or the product emitting smoke or strange odors, stop using it immediately and consult the dealer from whom you purchased the product. Continued use of the product before corrective actions are taken may result in an accident, injury or fire.
Never pull the plastic bag over your head. Otherwise, a serious injury or death from suffocation may occur.
Caution
Do not use batteries other than the type specified.
When placing batteries into the product, insert them as shown, paying close attention to the polarities (+ and -). If inserted improperly, the battery may explode, or leak electrolyte and contaminate the surrounding area.
Do not use this product for applications other than in-vehicle use. Otherwise, an electric shock or injury may result.
Do not allow children to play with the remote controls. Otherwise, the doors may be locked or unlocked, the security system armed or disarmed, or an alarm triggered unintentionally.
If this product is dropped or its case is damaged, disconnect the power supply lead and contact the dealer from whom you purchased it to obtain service. Otherwise, a fire or electric shock may result.
Remote Keyless Security system
Designed Specifically for your Vehicl
Related manuals for Toyota 4Runner TVIP V3 RS3200 2002 SUV Owner's Guide
Manualsnet FAQs
If you want to find out how the 4Runner Toyota works, you can view and download the Toyota 4Runner TVIP V3 RS3200 2002 SUV Owner's Guide on the Manualsnet website.
Yes, we have the Owner's Guide for Toyota 4Runner as well as other Toyota manuals. All you need to do is to use our search bar and find the user manual that you are looking for.
The Owner's Guide should include all the details that are needed to use a Toyota 4Runner. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.
The best way to navigate the Toyota 4Runner TVIP V3 RS3200 2002 SUV Owner's Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.
This Toyota 4Runner TVIP V3 RS3200 2002 SUV Owner's Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.
You can download Toyota 4Runner TVIP V3 RS3200 2002 SUV Owner's Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.
To be able to print Toyota 4Runner TVIP V3 RS3200 2002 SUV Owner's Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Toyota 4Runner TVIP V3 RS3200 2002 SUV Owner's Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.