Toyota Celica TVIP V5 RS3200 2003 Sports Car Onwer's Guide PDF

1 of 13
1 of 13

Summary of Content for Toyota Celica TVIP V5 RS3200 2003 Sports Car Onwer's Guide PDF

2003- CELICA TVIPV5 RS3200PLUS OWNERSGUIDE

Security System Designed for Use With your Vehicles

Remote Keyless Entry System

owners guide

RS3200 plus

Rev. A 05/30/02

090002-25210700

To better understand the features and functions of this security system, please read this Owners Guide completely prior to use.

TABLE OF CONTENTS

DESCRIPTION PAGE INTRODUCTION 2

BRIEF DESCRIPTIONRS3200 Plus FEATURES 3, 4

OPERATION ARMING THE RS3200 PLUS 5 DISARMING THE RS3200 PLUS 6 AUTOMATIC REARMING 7

ALARM INFORMATION ALARM TRIGGERS 8 ALARM DESCRIPTIONS 9 STOPPING AN ALARM 9

GLASS BREAKAGE SENSOR INFORMATION GLASS BREAKAGE SENSOR CHECK PROCEDURE 10

WARNING and CAUTION INFORMATION 11

TOYOTA RS3200 Plus Security system Page 1

INTRODUCTION Congratulations on your choice of the RS3200 Plus add-on security system to protect your vehicle! To get the most from the system, we strongly recommend that you read this Owners Guide completely to learn all of its features and functions.

The RS3200 Plus provides security through point-of-entry monitoring, glass breakage detection and ignition switch monitoring. While Armed, the system will be Triggered and sound an AlArm when a door, trunk or hatch is forcibly unlocked or opened*, or when a window is tapped on or broken. During the AlArm, the vehicles horn sounds and the headlights, tail lights and front marker lights flash. Also, the vehicles starter is disabled, preventing engine start. In addition to the comprehen- sive protection, the RS3200 Plus works in conjunction with your vehicles remote keyless entry sys- tem, enabling you to Arm and disArm the security system at the same time the doors are remotely locked and unlocked. In vehicles equipped with a buzzer, it will chirp when the system is remoTe

Armed and disArmed.

Page 2 TOYOTA RS3200 Plus Security system TOYOTA RS3200 Plus Security system Page 11

Caution

Do not use this product for applications other than in-vehicle use. Otherwise, an electric shock or injury may result.

Do not allow children to play with the remote controls. Otherwise, the doors may be locked or unlocked, the security system armed or disarmed, or an alarm triggered unintentionally.

If this product is dropped or its case is damaged, disconnect the power supply lead and contact the dealer from whom you purchased it to obtain service. Otherwise, a fire or electric shock may result.

Warning This product is applicable only to vehicles with 12V DC, negative grounding specifications.

Do not use in vehicles with 24V specifications. Otherwise, damage to the unit or a fire may result.

Never attempt to disassemble or modify the product. Otherwise, an accident, fire or electric shock may result.

When replacing fuses, be sure to use fuses with the same specified capacity (amperage.) Otherwise, damage to the unit or vehicle, fire or electric shock may result.

If an abnormal condition occurs, such as liquids spilling onto the product, or the product emitting smoke or strange odors, stop using it immediately and consult the dealer from whom you purchased the product. Continued use of the product before corrective actions are taken may result in an accident, injury or fire.

Never pull the plastic bag over your head. Otherwise, a serious injury or death from suffoca- tion may occur.

Page 10 TOYOTA RS3200 Plus Security system TOYOTA RS3200 Plus Security system Page 3

FEATURES FUNCTIONS

REMOTE ARMING/DISARMING

The RS3200 PLUS willARM 30 seconds after the lock but- ton on the remote keyless entry systems remote control is pressed. If your vehicle is equipped with a buzzer that chirps when the lock and unlock buttons on the remote controls are pressed, the buzzer will also chirp when the system is REMOTE ARMED and DISARMED.

AUTOMATIC REARMING

The RS3200 PLUS will automatically REARM at the same time the vehicles remote keyless entry system relocks the vehicles doors, if no door is opened within 30 seconds after REMOTE DISARMING.

KEY ARMING/DISARMING

The RS3200 PLUS will ARM 30 seconds after you close the trunk (if open) and lock the vehicles doors with the key, and will DISARM when you unlock a door with the key.

MANUAL ARMING When you lock the vehicle with the central lock switch (while a door is open), the RS3200 PLUS will ARM 30 seconds after you close all the doors and the trunk (if open).

IGNITION KEY DISARMING

The RS3200 PLUS may be DISARMED by inserting the key into the ignition switch and turning it to ON.

POINT-OF-ENTRY PROTECTION

Forcibly unlocking or opening a door or trunk while the RS3200 PLUS is ARMED will TRIGGER and ALARM immediately.

GLASS BREAKAGE SENSOR

The RS3200 PLUS utilizes a microphone (usually mounted in the STATUS MONITOR) to sense the noise from tapping on window glass, or glass breaking, and TRIGGER the system to sound an ALARM. It is fine tuned to listen for this type of noise, and ignore other sounds.

WARN AWAY ALARM When the GLASS BREAKAGE SENSORS microphone picks up tapping or breaking of window glass, it TRIGGERS a WARN AWAY ALARM; the headlights and tail and mark- ers lights flash, and the horn sounds for 20 seconds, but the starter is not disabled. If there is another detection of glass tapping or breaking, or if a door is opened or unlocked without a key, the regular ALARM is TRIGGERED.

IGNITION SWITCH MONITORING

While ARMED, the RS3200 PLUS monitors the ignition switch. If an attempt is made to start the vehicle without a key, an ALARM is TRIGGERED.

BRIEF DESCRIPTIONRS3200 Plus FEATURESGLASS BREAKAGE SENSOR INFORMATION The RS3200 Plus provides protection for your vehicle above and beyond entry point monitoringit listens for the noise made by tapping on, or breaking of glass. Using a microphone designed spe- cifically for this task, the glAss BreAkAge sensor is capable of ignoring other noises, which helps to prevent false alarms from occurring.

GLASS BREAKAGE SENSOR CHECK PROCEDURE

When the RS3200 Plus was installed in your vehicle, care was taken to adjust the sensitivity level of the glAss BreAkAge sensor. You may observe how it works following the procedure listed below.

1. Arm the system. Press the lock button on the remote control or lock the doors with the key.

(Remember, the system will not Arm if any door, the trunk or hatch is open.)

2. Wait until the sTATus moniTors LED starts flashing. The LED will flash 30 seconds after the last door, the trunk or hatch is closed.

3. With the tip of a key, tap the center of the drivers door window. Tap the glass with light to moderate force.

WARNING: Do not hit the glass with excessive force, especially in cold weather, or you may crack or break it.

A WArn AWAy AlArm should be Triggered. If the AlArm is not Triggered, make sure you performed the procedure correctly and try again. If you find that the system did not perform as expected,

contact your Toyota dealer for more information.

4. disArm the system to stop the WArn AWAy AlArm. Press the unlock button on the remote control or use the key to disArm the system.

FEATURES FUNCTIONS

STARTER DISABLE When an ALARM is TRIGGERED , the system disables the vehicles starter and prevents engine start until the system is reset (DISARMED).

TRIGGER MEMORY The user is notified that an ALARM occurred. Upon DISARMING, the system after an ALARM was TRIGGERED, the vehicles tail and marker lights will be turned on for 2 seconds.

EXTERIOR LIGHT ACTIVATION

The RS3200 PLUS flashes the vehicles tail and marker lights or turn signal lights during REMOTE ARMING and REMOTE DISARMING, and during an ALARM. Also, during an ALARM, the headlights flash.

BUZZER ACTIVATION If your vehicle is equipped with a buzzer that chirps when the lock and unlock buttons on the remote keyless entry systems remote controls are pressed, the buzzer will also chirp when the system is REMOTE ARMED and DISARMED.

HORN ACTIVATION During an ALARM, the RS3200 PLUS activates the vehicles horn.

POWER LOSS MEMORY

If power to the RS3200 PLUS is disrupted while it is ARMED, an ALARM is TRIGGERED once power is restored.

STATUS MONITOR This panel houses the GLASS BREAKAGE SENSOR micro- phone and the flashing LED that indicates the operating sta- tus of the security system.

Page 4 TOYOTA RS3200 Plus Security system TOYOTA RS3200 Plus Security system Page 9

BRIEF DESCRIPTIONRS3200 Plus FEATURES ALARM INFORMATION ALARM DESCRIPTIONS

Regular AlArm

When an AlArm is triggered in any way other than initial detection by the glAss BreAkAge

sensor,the following occur: The horn sounds repeatedly for 60 seconds. The headlights flash repeatedly for 60 seconds. The tail and marker or turn signal lights flash repeatedly for 60 seconds. The starter is disabled (no engine start) until the system is disArmed.

After 60 seconds of AlArm, the system will reArm and continue to protect the vehicle.

WArn-AWAy AlArm

Upon initial detection of noise from tapping on, or breaking glass, the glAss BreAkAge sensor

Triggers a WArn AWAy AlArm: The horn sounds repeatedly for 20 seconds. The headlights flash repeatedly for 20 seconds. The tail and marker or turn signal lights flash repeatedly for 20 seconds.

If the glAss BreAkAge sensor detects noise again, or if a door or trunk is opened while the system is still Armed, the regular AlArm (described above) is activated.

STOPPING AN ALARM

Simply disArm the system using the remote control or key as described on page 6.

The horn sounds

for 20 seconds

The horn sounds

for 60 seconds

heAdlighTs flAsh

for 60 seconds

The sTArTer is disABled unTil

The sysTem is disArmed

mArker or Turn

lighTs flAsh

for 60 seconds

heAdlighTs flAsh

for 20 seconds

mArker or Turn lighT

flAsh

for 20 seconds

TAil or Turn signAl ligTs

flAsh for 20 seconds

1

1

2

2

Page 8 TOYOTA RS3200 Plus Security system TOYOTA RS3200 Plus Security system Page 5

OPERATION ARMING THE RS3200 Plus

The system may be Armed in several ways. Do one of the following:

Lock the doors with your key: Remove the key from the ignition switch. Exit the vehicle, and close all the doors.* Close the trunk or hatch, if necessary.* Insert the key into the door key switch and turn it toward the front of the vehicle:

The sTATus moniTors LED turns on for 30 seconds, then starts flashing. The system is now Armed.

Lock the doors from inside the vehicle: Remove the key from the ignition switch. Open the drivers or front passengers door. Push the central lock switch. Exit the vehicle, and close all the doors.* Close the trunk or hatch, if necessary.* Then:

The sTATus moniTors LED turns on for 30 seconds, then starts flashing. The system is now Armed.

Lock the doors with the remote control: Remove the key from the ignition switch. Exit the vehicle, and close all the doors.* Close the trunk or hatch, if necessary.* Press the lock button on the remote control. Simultaneously:

The doors lock. The vehicles tail and marker lights or turn signal lights flash

once. The vehicles buzzer chirps once. The sTATus moniTors LED turns on for 30 seconds, then

starts flashing. The system is now Armed.

* The system will not Arm while any of the doors, trunk or hatch is open. If your vehicle is equipped with a buzzer.

Turn ToWArd The fronT

of The vehicle

Press And releAse

The lock BuTTon

Push The lock sWiTch While

The door is oPen

lighTs for

30 seconds

(Pre-Arm- ing) Then

flAshes

(sysTem is

Armed)

The TAil And mArker or Turn signAl lighTs flAsh

once When The sysTem is remoTe Armed

All doors lock When The

sysTem is remoTe Armed

1

1 2 3

1

2

3

ALARM INFORMATION ALARM TRIGGERS

While the system is Armed, an AlArm will be Triggered when any of the following occurs:

1 Forcibly opening a door, or the trunk or hatch without a key

Pulling the trunk release lever inside the vehicle will also Trigger

an AlArm.

2 Manually unlocking a door

Manually operating an inside lock button will Trigger an AlArm.

Note: Because this action will Trigger an AlArm, it is important that you do not Arm the system while someone is in the vehicle.

3 Hot wiring the vehicle

The RS3200 Plus can detect the absence of the ignition key if the ignition circuit is shorted in attempt to start the vehicle.

4 Tapping on or breaking the glass

The noise from tapping on, or breaking of glass Triggers a WArn

AWAy AlArm first, then a regular AlArm. See the description of how the glAss BreAkAge sensor Triggers AlArms on page 12.

5 Power restoration

if power to the system is interrupted while it is Armed, an AlArm will be Triggered immediately when power is restored.

1

Page 6 TOYOTA RS3200 PLUS Security system TOYOTA RS3200 PLUS Security system Page 7

OPERATION DISARMING THE RS3200 Plus

The system may be disArmed in several ways. Do one of the following:

Unlock the doors with your key: Insert the key into the door key switch and turn it toward the rear of the vehicle:

The sTATus moniTors LED stops flashing. The system is now disArmed.*

You may also disarm the system using the key in the back door; all doors will unlock at the same time.

Unlock the doors with the remote control: Press the unlock button on the remote control. Simultaneously:

The drivers door unlocks. The vehicles tail and marker or turn signal lights flash twice. The vehicles buzzer chirps twice.

The sTATus moniTors LED stops flashing. The system is now disArmed.* Press the unlock button again within 3 seconds after unlocking the

drivers door to unlock the remaining doors.

Use the ignition switch: Insert the key into the ignition switch, then turn it to ON.

The sTATus moniTors LED stops flashing. The system is now disArmed.*

This method of disarming is rarely used. You must be inside the vehicle while the system is armed in order to do it.

NOTE: If your vehicles tail and marker or turn signal lights turn on for 2 seconds when the system is disArmed,* the Trigger memory was activated; something Triggered an AlArm while you were away from the vehicle.

If your vehicle is equipped with a buzzer.

Turn ToWArd The reAr

of The vehicle

Turn The key To on To

disArm The sysTem

The drivers door unlocks

When The sysTem is remoTe

disArmed

The TAil And mArker or Turn signAl lighTs flAsh

TWice When The sysTem is remoTe disArmed

Push The unlock BuTTon

sToPs

flAshing

When The

sysTem is

disArmed

1

2

3

1

1

1 2 3

OPERATION AUTOMATIC REARMING

When you unlock the doors using the remote control, the RS3200 Plus is disArmed at the same time. However, if you do not open a door or the trunk within 30 seconds, the keyless entry system will relock the doors and the RS3200 Plus will reArm 30 seconds later.

How the RS3200 Plus automatically reArms:

0

15

30

45

The doors Are

unlocked By Pressing

The unlock BuTTon on

The remoTe conTrol...

When no door, Trunk

or hATch is oPened... for more ThAn 30

seconds... The keyless enTry

sysTem AuTomATicAlly

relocks The doors, Then The rs3200 Plus

AuTomATicAlly reArms.

The led Will lighT uP

for 30 seconds

(Pre-Arm), Then

flAsh When The

sysTem is Armed

Page 6 TOYOTA RS3200 PLUS Security system TOYOTA RS3200 PLUS Security system Page 7

OPERATION DISARMING THE RS3200 Plus

The system may be disArmed in several ways. Do one of the following:

Unlock the doors with your key: Insert the key into the door key switch and turn it toward the rear of the vehicle:

The sTATus moniTors LED stops flashing. The system is now disArmed.*

You may also disarm the system using the key in the back door; all doors will unlock at the same time.

Unlock the doors with the remote control: Press the unlock button on the remote control. Simultaneously:

The drivers door unlocks. The vehicles tail and marker or turn signal lights flash twice. The vehicles buzzer chirps twice.

The sTATus moniTors LED stops flashing. The system is now disArmed.* Press the unlock button again within 3 seconds after unlocking the

drivers door to unlock the remaining doors.

Use the ignition switch: Insert the key into the ignition switch, then turn it to ON.

The sTATus moniTors LED stops flashing. The system is now disArmed.*

This method of disarming is rarely used. You must be inside the vehicle while the system is armed in order to do it.

NOTE: If your vehicles tail and marker or turn signal lights turn on for 2 seconds when the system is disArmed,* the Trigger memory was activated; something Triggered an AlArm while you were away from the vehicle.

If your vehicle is equipped with a buzzer.

Turn ToWArd The reAr

of The vehicle

Turn The key To on To

disArm The sysTem

The drivers door unlocks

When The sysTem is remoTe

disArmed

The TAil And mArker or Turn signAl lighTs flAsh

TWice When The sysTem is remoTe disArmed

Push The unlock BuTTon

sToPs

flAshing

When The

sysTem is

disArmed

1

2

3

1

1

1 2 3

OPERATION AUTOMATIC REARMING

When you unlock the doors using the remote control, the RS3200 Plus is disArmed at the same time. However, if you do not open a door or the trunk within 30 seconds, the keyless entry system will relock the doors and the RS3200 Plus will reArm 30 seconds later.

How the RS3200 Plus automatically reArms:

0

15

30

45

The doors Are

unlocked By Pressing

The unlock BuTTon on

The remoTe conTrol...

When no door, Trunk

or hATch is oPened... for more ThAn 30

seconds... The keyless enTry

sysTem AuTomATicAlly

relocks The doors, Then The rs3200 Plus

AuTomATicAlly reArms.

The led Will lighT uP

for 30 seconds

(Pre-Arm), Then

flAsh When The

sysTem is Armed

Page 8 TOYOTA RS3200 Plus Security system TOYOTA RS3200 Plus Security system Page 5

OPERATION ARMING THE RS3200 Plus

The system may be Armed in several ways. Do one of the following:

Lock the doors with your key: Remove the key from the ignition switch. Exit the vehicle, and close all the doors.* Close the trunk or hatch, if necessary.* Insert the key into the door key switch and turn it toward the front of the vehicle:

The sTATus moniTors LED turns on for 30 seconds, then starts flashing. The system is now Armed.

Lock the doors from inside the vehicle: Remove the key from the ignition switch. Open the drivers or front passengers door. Push the central lock switch. Exit the vehicle, and close all the doors.* Close the trunk or hatch, if necessary.* Then:

The sTATus moniTors LED turns on for 30 seconds, then starts flashing. The system is now Armed.

Lock the doors with the remote control: Remove the key from the ignition switch. Exit the vehicle, and close all the doors.* Close the trunk or hatch, if necessary.* Press the lock button on the remote control. Simultaneously:

The doors lock. The vehicles tail and marker lights or turn signal lights flash

once. The vehicles buzzer chirps once. The sTATus moniTors LED turns on for 30 seconds, then

starts flashing. The system is now Armed.

* The system will not Arm while any of the doors, trunk or hatch is open. If your vehicle is equipped with a buzzer.

Turn ToWArd The fronT

of The vehicle

Press And releAse

The lock BuTTon

Push The lock sWiTch While

The door is oPen

lighTs for

30 seconds

(Pre-Arm- ing) Then

flAshes

(sysTem is

Armed)

The TAil And mArker or Turn signAl lighTs flAsh

once When The sysTem is remoTe Armed

All doors lock When The

sysTem is remoTe Armed

1

1 2 3

1

2

3

ALARM INFORMATION ALARM TRIGGERS

While the system is Armed, an AlArm will be Triggered when any of the following occurs:

1 Forcibly opening a door, or the trunk or hatch without a key

Pulling the trunk release lever inside the vehicle will also Trigger

an AlArm.

2 Manually unlocking a door

Manually operating an inside lock button will Trigger an AlArm.

Note: Because this action will Trigger an AlArm, it is important that you do not Arm the system while someone is in the vehicle.

3 Hot wiring the vehicle

The RS3200 Plus can detect the absence of the ignition key if the ignition circuit is shorted in attempt to start the vehicle.

4 Tapping on or breaking the glass

The noise from tapping on, or breaking of glass Triggers a WArn

AWAy AlArm first, then a regular AlArm. See the description of how the glAss BreAkAge sensor Triggers AlArms on page 12.

5 Power restoration

if power to the system is interrupted while it is Armed, an AlArm will be Triggered immediately when power is restored.

1

FEATURES FUNCTIONS

STARTER DISABLE When an ALARM is TRIGGERED , the system disables the vehicles starter and prevents engine start until the system is reset (DISARMED).

TRIGGER MEMORY The user is notified that an ALARM occurred. Upon DISARMING, the system after an ALARM was TRIGGERED, the vehicles tail and marker lights will be turned on for 2 seconds.

EXTERIOR LIGHT ACTIVATION

The RS3200 PLUS flashes the vehicles tail and marker lights or turn signal lights during REMOTE ARMING and REMOTE DISARMING, and during an ALARM. Also, during an ALARM, the headlights flash.

BUZZER ACTIVATION If your vehicle is equipped with a buzzer that chirps when the lock and unlock buttons on the remote keyless entry systems remote controls are pressed, the buzzer will also chirp when the system is REMOTE ARMED and DISARMED.

HORN ACTIVATION During an ALARM, the RS3200 PLUS activates the vehicles horn.

POWER LOSS MEMORY

If power to the RS3200 PLUS is disrupted while it is ARMED, an ALARM is TRIGGERED once power is restored.

STATUS MONITOR This panel houses the GLASS BREAKAGE SENSOR micro- phone and the flashing LED that indicates the operating sta- tus of the security system.

Page 4 TOYOTA RS3200 Plus Security system TOYOTA RS3200 Plus Security system Page 9

BRIEF DESCRIPTIONRS3200 Plus FEATURES ALARM INFORMATION ALARM DESCRIPTIONS

Regular AlArm

When an AlArm is triggered in any way other than initial detection by the glAss BreAkAge

sensor,the following occur: The horn sounds repeatedly for 60 seconds. The headlights flash repeatedly for 60 seconds. The tail and marker or turn signal lights flash repeatedly for 60 seconds. The starter is disabled (no engine start) until the system is disArmed.

After 60 seconds of AlArm, the system will reArm and continue to protect the vehicle.

WArn-AWAy AlArm

Upon initial detection of noise from tapping on, or breaking glass, the glAss BreAkAge sensor

Triggers a WArn AWAy AlArm: The horn sounds repeatedly for 20 seconds. The headlights flash repeatedly for 20 seconds. The tail and marker or turn signal lights flash repeatedly for 20 seconds.

If the glAss BreAkAge sensor detects noise again, or if a door or trunk is opened while the system is still Armed, the regular AlArm (described above) is activated.

STOPPING AN ALARM

Simply disArm the system using the remote control or key as described on page 6.

The horn sounds

for 20 seconds

The horn sounds

for 60 seconds

heAdlighTs flAsh

for 60 seconds

The sTArTer is disABled unTil

The sysTem is disArmed

mArker or Turn

lighTs flAsh

for 60 seconds

heAdlighTs flAsh

for 20 seconds

mArker or Turn lighT

flAsh

for 20 seconds

TAil or Turn signAl ligTs

flAsh for 20 seconds

1

1

2

2

Page 10 TOYOTA RS3200 Plus Security system TOYOTA RS3200 Plus Security system Page 3

FEATURES FUNCTIONS

REMOTE ARMING/DISARMING

The RS3200 PLUS willARM 30 seconds after the lock but- ton on the remote keyless entry systems remote control is pressed. If your vehicle is equipped with a buzzer that chirps when the lock and unlock buttons on the remote controls are pressed, the buzzer will also chirp when the system is REMOTE ARMED and DISARMED.

AUTOMATIC REARMING

The RS3200 PLUS will automatically REARM at the same time the vehicles remote keyless entry system relocks the vehicles doors, if no door is opened within 30 seconds after REMOTE DISARMING.

KEY ARMING/DISARMING

The RS3200 PLUS will ARM 30 seconds after you close the trunk (if open) and lock the vehicles doors with the key, and will DISARM when you unlock a door with the key.

MANUAL ARMING When you lock the vehicle with the central lock switch (while a door is open), the RS3200 PLUS will ARM 30 seconds after you close all the doors and the trunk (if open).

IGNITION KEY DISARMING

The RS3200 PLUS may be DISARMED by inserting the key into the ignition switch and turning it to ON.

POINT-OF-ENTRY PROTECTION

Forcibly unlocking or opening a door or trunk while the RS3200 PLUS is ARMED will TRIGGER and ALARM immediately.

GLASS BREAKAGE SENSOR

The RS3200 PLUS utilizes a microphone (usually mounted in the STATUS MONITOR) to sense the noise from tapping on window glass, or glass breaking, and TRIGGER the system to sound an ALARM. It is fine tuned to listen for this type of noise, and ignore other sounds.

WARN AWAY ALARM When the GLASS BREAKAGE SENSORS microphone picks up tapping or breaking of window glass, it TRIGGERS a WARN AWAY ALARM; the headlights and tail and mark- ers lights flash, and the horn sounds for 20 seconds, but the starter is not disabled. If there is another detection of glass tapping or breaking, or if a door is opened or unlocked without a key, the regular ALARM is TRIGGERED.

IGNITION SWITCH MONITORING

While ARMED, the RS3200 PLUS monitors the ignition switch. If an attempt is made to start the vehicle without a key, an ALARM is TRIGGERED.

BRIEF DESCRIPTIONRS3200 Plus FEATURESGLASS BREAKAGE SENSOR INFORMATION The RS3200 Plus provides protection for your vehicle above and beyond entry point monitoringit listens for the noise made by tapping on, or breaking of glass. Using a microphone designed spe- cifically for this task, the glAss BreAkAge sensor is capable of ignoring other noises, which helps to prevent false alarms from occurring.

GLASS BREAKAGE SENSOR CHECK PROCEDURE

When the RS3200 Plus was installed in your vehicle, care was taken to adjust the sensitivity level of the glAss BreAkAge sensor. You may observe how it works following the procedure listed below.

1. Arm the system. Press the lock button on the remote control or lock the doors with the key.

(Remember, the system will not Arm if any door, the trunk or hatch is open.)

2. Wait until the sTATus moniTors LED starts flashing. The LED will flash 30 seconds after the last door, the trunk or hatch is closed.

3. With the tip of a key, tap the center of the drivers door window. Tap the glass with light to moderate force.

WARNING: Do not hit the glass with excessive force, especially in cold weather, or you may crack or break it.

A WArn AWAy AlArm should be Triggered. If the AlArm is not Triggered, make sure you performed the procedure correctly and try again. If you find that the system did not perform as expected,

contact your Toyota dealer for more information.

4. disArm the system to stop the WArn AWAy AlArm. Press the unlock button on the remote control or use the key to disArm the system.

INTRODUCTION Congratulations on your choice of the RS3200 Plus add-on security system to protect your vehicle! To get the most from the system, we strongly recommend that you read this Owners Guide completely to learn all of its features and functions.

The RS3200 Plus provides security through point-of-entry monitoring, glass breakage detection and ignition switch monitoring. While Armed, the system will be Triggered and sound an AlArm when a door, trunk or hatch is forcibly unlocked or opened*, or when a window is tapped on or broken. During the AlArm, the vehicles horn sounds and the headlights, tail lights and front marker lights flash. Also, the vehicles starter is disabled, preventing engine start. In addition to the comprehen- sive protection, the RS3200 Plus works in conjunction with your vehicles remote keyless entry sys- tem, enabling you to Arm and disArm the security system at the same time the doors are remotely locked and unlocked. In vehicles equipped with a buzzer, it will chirp when the system is remoTe

Armed and disArmed.

Page 2 TOYOTA RS3200 Plus Security system TOYOTA RS3200 Plus Security system Page 11

Caution

Do not use this product for applications other than in-vehicle use. Otherwise, an electric shock or injury may result.

Do not allow children to play with the remote controls. Otherwise, the doors may be locked or unlocked, the security system armed or disarmed, or an alarm triggered unintentionally.

If this product is dropped or its case is damaged, disconnect the power supply lead and contact the dealer from whom you purchased it to obtain service. Otherwise, a fire or electric shock may result.

Warning This product is applicable only to vehicles with 12V DC, negative grounding specifications.

Do not use in vehicles with 24V specifications. Otherwise, damage to the unit or a fire may result.

Never attempt to disassemble or modify the product. Otherwise, an accident, fire or electric shock may result.

When replacing fuses, be sure to use fuses with the same specified capacity (amperage.) Otherwise, damage to the unit or vehicle, fire or electric shock may result.

If an abnormal condition occurs, such as liquids spilling onto the product, or the product emitting smoke or strange odors, stop using it immediately and consult the dealer from whom you purchased the product. Continued use of the product before corrective actions are taken may result in an accident, injury or fire.

Never pull the plastic bag over your head. Otherwise, a serious injury or death from suffoca- tion may occur.

Security System Designed for Use With your Vehicles

Remote Keyless Entry System

owners guide

RS3200 plus

Rev. A 05/30/02

Manualsnet FAQs

If you want to find out how the TVIP V5 RS3200 Toyota works, you can view and download the Toyota Celica TVIP V5 RS3200 2003 Sports Car Onwer's Guide on the Manualsnet website.

Yes, we have the Onwer's Guide for Toyota TVIP V5 RS3200 as well as other Toyota manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Onwer's Guide should include all the details that are needed to use a Toyota TVIP V5 RS3200. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Toyota Celica TVIP V5 RS3200 2003 Sports Car Onwer's Guide is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Toyota Celica TVIP V5 RS3200 2003 Sports Car Onwer's Guide consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Toyota Celica TVIP V5 RS3200 2003 Sports Car Onwer's Guide free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Toyota Celica TVIP V5 RS3200 2003 Sports Car Onwer's Guide, simply download the document to your computer. Once downloaded, open the PDF file and print the Toyota Celica TVIP V5 RS3200 2003 Sports Car Onwer's Guide as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.