Toyota MR2 Spyder TVIP V3 RS3200 2003 Roadster Programming Instructions PDF

1 of 10
1 of 10

Summary of Content for Toyota MR2 Spyder TVIP V3 RS3200 2003 Roadster Programming Instructions PDF

TVIP V3 RS3200 SYSTEM PROGRAMMING INSTRUCTIONS

1 of 10

1 egaP GNIMMARGORP METSYS PIVT ATOYOT

PROGRAMMING TABLE OF CONTENTS

EGAP GNIMMARGORP 0023SR ADD ADDITIONAL REMOTE CONTROL(S) TO SYSTEM 2, 3 REPROGRAM EXISTING REMOTE CONTROLS 4, 5 REMOTE CONTROL FUNCTION SELECT 6, 7 CLEAR ALL REMOTE CONTROL CODES 8 PASSIVE ARMING ON/ OFF SELECTION AND 9 ENTRY DELAY TIME SELECTION IGNITIONCONTROLLED AUTOMATIC DOOR 10 LOCK/ UNLOCK

Notes: For factory remote keyless entry system programming information, refer to the vehicles repair manual.

Refer to the RS3000 Owners guide for RS3000 feature programming.

TVIP V3 RS3200 SYSTEM PROGRAMMING INSTRUCTIONS

2 of 10

Page 2 TOYOTA TVIP SYSTEM PROGRAMMINGRS3200

ADD ADDITIONAL REMOTE CONTROL(S) TO SYSTEM Follow this procedure to add additional remote controls to a system. The RS3200 may be programmed to operate with a maximum of four remote controls. When a new remote controls is programmed, it will work in the default operation mode (press the UNLOCK button twice to unlock all doors and no AUX button function on 4 button remote controls); to change the operation mode, you must perform the separate REMOTE CONTROL FUNCTION SELECT procedure as shown on pages 6 and 7.

* If the system does not activate the lights, buzzer and door locks 1 time, start over.

1. Before you begin:Open the drivers door and remove the key from the ignition switch.

2. Start the programming procedure. (Complete these steps within 40 seconds.)

a. Insert the key into, and remove it from the ignition switch 2 times.

b. Close, then open the drivers door 2 times.

c. Insert the key into, and remove it from the ignition switch 1 time.

d. Close, the open the drivers door 2 times.

e. Insert the key into, the ignition switch and leave it in.

f. Close the drivers door.

g. Turn the key from LOCK to ON, then back to LOCK.

h. Remove the key from the ignition switch.

i. The tail and marker lights flash 1 time, the buzzer chirps 1 time and the doors lock and unlock 1 time.*

TVIP V3 RS3200 SYSTEM PROGRAMMING INSTRUCTIONS

3 of 10

3 egaP GNIMMARGORP METSYS PIVT ATOYOT

ADD ADDITIONAL REMOTE CONTROL(S) TO SYSTEM (continued)

* If the system activates the lights, buzzer and door locks 2 times, start over.

3. Program (add) an additional remote control.

a. Press and release both the LOCK and UNLOCK buttons on one remote control at the same time.

b. Press and release the LOCK button.

c. The tail and marker lights flash 1 time, the buzzer chirps 1 time, and the doors lock and unlock 1 time. *

Note: Repeat the above steps to add additional remote controls.

4. Complete the programming steps.

a. Open the drivers door

TVIP V3 RS3200 SYSTEM PROGRAMMING INSTRUCTIONS

4 of 10

Page 4 TOYOTA TVIP SYSTEM PROGRAMMINGRS3200

REPROGRAM EXISTING REMOTE CONTROLS Follow this procedure to clear all existing remote control codes and reprogram existing remote controls to a system. When existing remote controls are reprogrammed, they will work in the default operation mode (press the UNLOCK button twice to unlock all doors and no AUX button function on 4 button remote controls); to change the operation mode, you must perform the separate REMOTE CONTROL FUNCTION SELECT procedure as shown on pages 6 and 7.

*If the system does not activate the lights, buzzer and door locks 2 times, start over.

1. Before you begin: Open the drivers door and remove the key from the ignition switch.

2. Start the programming procedure: (Complete these steps within 40 seconds.)

a. Insert the key into, and remove it from the ignition switch 2 times.

b. Close, then open the drivers door 2 times.

c. Insert the key into, and remove it from the ignition switch 1 time.

d. Close, then open the drivers door 2 times.

e. Insert the key into the ignition switch and leave it in.

f. Close the drivers door.

g. Turn the key from LOCK to ON 2 times (ending at LOCK).

h. Remove the key from the ignition switch.

i. The tail and marker lights flash 2 times, the buzzer chirps 2 times and the doors lock and unlock 2 times.*

TVIP V3 RS3200 SYSTEM PROGRAMMING INSTRUCTIONS

5 of 10

5 egaP GNIMMARGORP METSYS PIVT ATOYOT

REPROGRAM EXISTING REMOTE CONTROLS (continued)

* If the system activates the lights, buzzer and door locks 2 times, start over.

3. Reprogram an existing remote control.

a. Press and release both the LOCK and UNLOCK buttons on one remote control at the same time.

b. Press and release the LOCK button.

c. The tail and marker lights flash 1 time, the buzzer chirps 1 time, and the doors lock and unlock 1 time. *

Note: Repeat the above steps to program (add) additional remote controls.

4. Complete the programming steps.

a. Open the drivers door.

TVIP V3 RS3200 SYSTEM PROGRAMMING INSTRUCTIONS

6 of 10

Page 6 TOYOTA TVIP SYSTEM PROGRAMMINGRS3200

REMOTE CONTROL FUNCTION SELECT

Follow this procedure to change the operating functions of remote controls already programmed into a system. You may change the remote controls default unlock operation mode so that pressing the UNLOCK button once causes all doors to unlock at the same time. Also, you may activate the AUX button function on 4 button remote controls.

* If the system does not activate the lights, buzzer and door locks 4 times, start over.

1. Before you begin: Open the drivers door and remove the key from the ignition switch.

2. Start the programming procedure. (Complete these steps within 40 seconds.)

a. Insert the key into, and remove it from the ignition switch 2 times.

b. Close, then open the drivers door 2 times.

c. Insert the key into, and remove it from the ignition switch 1 time.

d. Close, then open the drivers door 2 times.

e. Insert the key into, the ignition switch and leave it in.

f. Close the drivers door.

g. Turn the key from LOCK to ON 4 times (ending at LOCK).

h. Remove the key from the ignition switch.

i. The tail and marker lights flash 4 times, the buzzer chirps 4 times and the doors lock and unlock 4 times.*

TVIP V3 RS3200 SYSTEM PROGRAMMING INSTRUCTIONS

7 of 10

7 egaP GNIMMARGORP METSYS PIVT ATOYOT

REMOTE CONTROL FUNCTION SELECT (continued)

* Program for 4 button remote controls, only. If the system activates the lights, buzzer and door locks 2 times, start over.

3. Select the operating functions for an existing remote control.

a. Press and release both the LOCK and UNLOCK buttons on one remote control at the same time.

b. Select one of the following modes:

Press and release the LOCK button to select double unlock function (press the UNLOCK button twice to unlock all the doors.)

or Press and release the UNLOCK button to select all door unlock function (press the UNLOCK button once to unlock all the doors at the same time.)

or Press and release the AUX button to select double unlock function (press the UNLOCK button twice to unlock all the doors) and activate the auxilary output for the optional electric trunk release accessory. *

or Press and release the PANIC button to select all door unlock function (press the UNLOCK button once to unlock all the doors at the same time) and activate

c. The tail and marker lights flash 1 time, the buzzer chirps 1 time, and the dorrs lock and unlock 1 time.

Note: Repeat the above steps to select the operating functions for additional remote controls.

4. Complete the programming steps.

a. Open the driver s door.

TVIP V3 RS3200 SYSTEM PROGRAMMING INSTRUCTIONS

8 of 10

2. Start the programming procedure. (Complete these steps within 40 seconds.)

Page 8 TOYOTA TVIP SYSTEM PROGRAMMINGRS3200

CLEAR ALL REMOTE CONTROL CODES

Follow this procedure to clear all remote controls programmed to operate the system. Please note, if you have remote controls to program into the system and you want to first clear all existing remote controls from the system, follow the reprogram procedure as shown on pages 4 and 5.

* If the system does not activate the lights, buzzer and door locks 5 times, start over.

1. Before you begin: Open the drivers door and remove the key from the ignition switch.

a. Insert the key into, and remove it from the ignition switch 2 times.

b. Close, then open the drivers door 2 times.

c. Insert the key into, and remove it from the ignition switch 1 time.

d. Close, then open the drivers door 2 times.

e. Insert the key into, the ignition switch and leave it in.

f. Close the drivers door.

g. Turn the key from LOCK to ON 5 times (ending at LOCK).

h. Remove the key from the ignition switch.

i. The tail and marker lights flash 5 times, the buzzer chirps 5 times and the doors lock and unlock 5 times.* a. Open the drivers door.

3. Complete the code clearing procedure.

TVIP V3 RS3200 SYSTEM PROGRAMMING INSTRUCTIONS

9 of 10

9 egaP GNIMMARGORP METSYS PIVT ATOYOT

PASSIVE ARMING ON/ OFF SELECTION AND ENTRY DELAY TIME SELECTION

The RS3200 is factory set to not passively arm. To change the systems operation for passive arming, as well as to adjust the entry delay time, follow the procedure below.

1. Before you begin: Close all the doors and the trunk or hatch, unlock all the doors with the inside lock switch, then remove the key from the ignition switch.

a. Using a remote control, lock, then unlock the doors 3 times.

2. Start the programming procedure. (Complete these steps within 30 seconds.)

b. Open the drivers door. c. Lock, then unlock the drivers door inside lock button 3 times.

d. The system locks the door in 2 seconds; if this does not happen, start over.

e. Unlock the drivers door inside lock button.

a. Close, then open the door: 2 times= passive arming off 3 times= passive arming on, 0 sec. entry delay. 4 times= passive arming on, 15 sec. entry delay. 5 times= passive arming on, 30 sec. entry delay.

b. Lock, then unlock the drivers door inside lock button 1 time.

c. The system locks the door in 2 seconds; Programming is now complete. If this does not happen, start over.

3. Select the operating mode and entry time delay, and complete the programming steps.

TVIP V3 RS3200 SYSTEM PROGRAMMING INSTRUCTIONS

10 of 10

Page 10 TOYOTA TVIP SYSTEM PROGRAMMINGRS3200

IGNITIONCONTROLLED AUTOMATIC DOOR LOCK/ UNLOCK

When all doors are closed, the RS3200 is factory set to automatically lock the vehicles door when the ignition key is turned to ON or START, and unlock them (open or not) when the key is turned back to ACC or LOCK. Follow the procedure below to change this features operation mode.

1. Before you begin: Open the drivers door and remove the key from the ignition switch.

2. Start the programming procedure. (Complete these steps within 30 seconds.)

a. Insert the key into the ignition switch and turn it from LOCK to ON 5 times (ending at ON).

b. The tail and marker lights flash 1 time, and the buzzer chirps 1 time.

c. The status monitors LED (or the engine immobilizer systems LED) turns on for 30 seconds.

Note: If the system does not activate the lights and buzzer, start over.

3. Select the operating mode and complete the programming steps.

a. Close the door: Ignition controlled door locks on. Close, then open and close the door: Ignition con

Manualsnet FAQs

If you want to find out how the TVIP V3 RS3200 Toyota works, you can view and download the Toyota MR2 Spyder TVIP V3 RS3200 2003 Roadster Programming Instructions on the Manualsnet website.

Yes, we have the Programming Instructions for Toyota TVIP V3 RS3200 as well as other Toyota manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Programming Instructions should include all the details that are needed to use a Toyota TVIP V3 RS3200. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Toyota MR2 Spyder TVIP V3 RS3200 2003 Roadster Programming Instructions is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Toyota MR2 Spyder TVIP V3 RS3200 2003 Roadster Programming Instructions consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Toyota MR2 Spyder TVIP V3 RS3200 2003 Roadster Programming Instructions free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Toyota MR2 Spyder TVIP V3 RS3200 2003 Roadster Programming Instructions, simply download the document to your computer. Once downloaded, open the PDF file and print the Toyota MR2 Spyder TVIP V3 RS3200 2003 Roadster Programming Instructions as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.