Toyota MR2 Spyder TVIP V5 RS3200 2005 Roadster Owner's Manual PDF

1 of 15
1 of 15

Summary of Content for Toyota MR2 Spyder TVIP V5 RS3200 2005 Roadster Owner's Manual PDF

2003- MR2 SPYDER TVIP V5 RS3200 PLUS OWNERS GUIDE

Remote Keyless Security system Designed Specifically for your Vehicle

owners guide

RS3200

090002-25200700

Rev. A 6/07/02

FOR MR2-SPYDER PLUS

Page 12 TOYOTA RS3200 PLUS Security system

To better understand the features and functions of this security system, please read this Owners Guide completely prior to use.

TABLE OF CONTENTS

DESCRIPTION PAGE INTRODUCTION 2 BRIEF DESCRIPTIONRS3200 PLUS FEATURES 3, 4 OPERATION ARMING THE RS3200 PLUS (except PASSIVE ARMING) 5 DISARMING THE RS3200 PLUS(except PASSIVE DISARMING) 6 PASSIVE (AUTOMATIC) ARMING & DISARMING 7 AUTOMATIC REARMING 8 ALARM INFORMATION

ALARM TRIGGERS 9 ALARM DESCRIPTIONS 10 STOPPING AN ALARM 10 RADAR SENSOR INFORMATION 11 PROGRAMMING PASSIVE (AUTOMATIC) ARMING AND ENTRY DELAY 12 WARNING AND CAUTION INFORMATION 13

TOYOTA RS3200 PLUS Security system Page 1

PROGRAMMING

PASSIVE ARMING ON/OFF SELECTION, ENTRY DELAY TIME SELECTION

The RS3200 PLUS is factory-set to not PASSIVELY ARM. To change the systems operation for PASSIVE ARMING operation, as well as adjust the ENTRY DELAY time, follow the procedure below. For more information on this feature, please refer to page 8.

1. Before you begin: Close all the doors, and the trunk or hatch. Unlock all the doors with the inside lock switch. Remove the key from the ignition switch.

2. Start the Programming Procedure. (Complete these steps within 30 seconds.)

3. Select the Operating Mode and Complete the Programming Procedure.

a. Using the remote control, lock, then unlock the doors 3 times.

b. Open the drivers door.

b. Lock then unlock the drivers door inside lock button 1 time.

a. Close, then Open the door: 2 times = PASSIVE ARMING OFF 3 times = PASSIVE ARMING ON, 0 Sec. ENTRY DELAY 4 times = PASSIVE ARMING ON, 15 Sec. ENTRY DELAY 5 times = PASSIVE ARMING ON, 30 Sec. ENTRY DELAY

c. Lock, then unlock the drivers door inside lock button 3 times.

d. The system locks the door in 2 seconds; if this does not happen, start over.

c. The system locks the door in 2 seconds; if this

does not happen, start over. Programming is now complete.

e. Unlock the drivers door inside lock button.

INTRODUCTION

Congratulations on your choice of the RS3200 PLUS security system to protect your vehicle! To get the most from the system, we strongly recommend that you read this Owners Guide complete- ly to learn all of its features and functions.

The RS3200 PLUS provides comprehensive security protection through point-of-entry monitoring, intrusion detection and ignition switch monitoring. While ARMED, the system will be TRIGGERED and sound an ALARM when a door, trunk or hatch is forcibly unlocked or opened*, or when someone intrudes into the vehicle. This system is a vehicle theft deterrent and will not prevent theft of personal goods in vehicle. For additional security, it is recommended that the vehicle top be in the closed position. During the ALARM, the vehicles horn will sound and the headlights, tail lights and front marker lights will flash. Also,the vehicles starter is disabled, to prevent engine start.

An important note about your system

Throughout this guide, there are references to the STATUS MONITOR for this system. This panel holds the LED indicator (for the systems operating status). In vehicles with an engine immobilizer, there is already a LED installed in the vehicle. If your vehicle falls into this category, remember to look at that LED when the information refers to the STATUS MONITOR. If you do not know where the LED is located, refer to your vehicles owners guide for specific information.

* When the system is PASSIVELY (AUTOMATICALLY) ARMED, there is an ENTRY DELAY that will elapse when a door is opened before an ALARM is TRIGGERED.

YOUR ENGINE IMMOBILIZER SYSTEM LED MAY LOOK

DIFFERENT THAN THE ONE

ILLUSTRATED HERE

Page 2 TOYOTA RS3200 PLUS Security system TOYOTA RS3200 PLUS Security system Page 11

1 2 3

1 2 3

RADAR SENSOR INFORMATION

RADAR SENSOR CHECK PROCEDURE

1. ARM the system. Press the LOCK button on the remote control or lock the doors with the key.

(Remember, the system will not ARM if any door is open.)

2. Wait until the STATUS MONITORS LED starts flashing. The LED will flash 30 seconds after the last door, the trunk or hatch is closed.

3. Move inside the vehicle. When movement occurs inside the vehicle, A WARN AWAY ALARM activates for 20 seconds. If sensor detects 2nd movement within 60

seconds after the 1st warn away alarm trigger, then a regular ALARM activates for 60 seconds.

Note: If you find that the system does not perform as expected, contact your Toyota dealer for more information.

4. DISARM the system to stop the WARN AWAY ALARM. Press the UNLOCK button on the remote control or use the key to DISARM the system.

RADAR SENSOR OFF MODE

THE RADAR SENSOR CAN BE DEACTIVATED. PERFORM THE FOLLOWING: PUSH THE SENSOR OFF SWITCH ON THE INSTRUMENT PANEL BEFORE ARMING BY KEY OR REMOTE CONTROL.

IMMOBILIZER LED STARTS BLINKING.

ARM THE SYSTEM WITH THE REMOTE CONTROL OR KEY WHILE THE IMMOBILIZER LED IS BLINKING. THE RADAR SENSOR WILL DEACTIVATE DURING ARMING.

NOTE: IF YOU DISARM THE SYSTEM AFTER YOU SET THE RADAR SENSOR OFF, YOU HAVE TO REPEAT THE ABOVE PROCEDURE WHEN YOU ARM THE SYSTEM IF YOU WANT TO DEACTIVATE THE RADAR SENSOR AGAIN. THE SYSTEM WILL AUTOMATICALLY CANCEL THE RADAR SENSOR OFF MODE WHEN DISARMED.

OFF

Page 10 TOYOTA RS3200 PLUS Security system TOYOTA RS3200 PLUS Security system Page 3

FEATURES FUNCTIONS The RS3200 PLUS will ARM 30 seconds after the LOCK button on the remote control is pressed, and DISARM when the UNLOCK button is pressed. If your vehicle is equipped with a buzzer that chirps when the lock and unlock buttons on the remote controls are pressed, the buzzer will also chirp when the system is REMOTE ARMED and DISARMED. The RS3200 PLUS will automatically RELOCK the vehicles doors if no door is opened within 30 seconds after REMOTE DISARMING, then will REARM 30 seconds later. The RS3200 PLUS will ARM 30 seconds after you close the trunk (if open) and lock the vehicles doors with the key, and will DISARM when you unlock a door with the key. The RS3200 PLUS may be programmed to automatically ARM 30 seconds after the ignition key is removed, the vehicle exited and the last doorand the trunk closed, without the necessity of locking the doors. The RS3200 PLUS may be DISARMED with the vehicles ignition key after it was PASSIVELY ARMED. When the RS3200 PLUS has been PASSIVELY ARMED, an ENTRY DELAY (user-selectable at 0, 15, or 30 seconds) will start when a door is opened before an ALARM is TRIGGERED. When you lock the vehicle with a central lock switch (while a door is open), the RS3200 PLUS will ARM 30 seconds after you close all the doors and the trunk (if open).

The RS3200 PLUS may be DISARMED by inserting the key into the ignition switch and turning it to ON.

Forcibly unlocking or opening a door, hatch or trunk while the RS3200 PLUS is ARMED will TRIGGER an ALARM immediately. (If the system was PASSIVELY ARMED, the ENTRY DELAY must pass before the ALARM is TRIGGERED.)

The RS3200 PLUS utilizes RADAR SENSOR to sense the intrusion from outside, and TRIGGER an ALARM . It is fine tuned to detect unauthorized movement inside the vehicle. When RADAR SENSOR detects the intrusion, it TRIGGERS a WARN AWAY ALARM; the headlights and tail and marker lights flash, and the horn sounds for 20 seconds, but the starter is not disabled. If there is another detection of a door is opened or unlocked without a key, the regular ALARM is TRIGGERED. While ARMED, the RS3200 PLUS monitors the ignition switch. If an attempt is made to start the vehicle without a key, an ALARM is trig- gered.

REMOTE ARMING/DISARMING

AUTOMATIC REARMING

KEY ARMING/DISARMING

PASSIVE (AUTOMATIC) ARMING

PASSIVE DISARMING

ADJUSTABLE ENTRY DELAY

MANUAL ARMING

IGNITION KEY DISARMING POINT-OF-ENTRY PROTECTION

RADAR SENSOR

WARN AWAY ALARM

IGNITION SWITCH MONITORING

BRIEF DESCRIPTIONRS3200 PLUS FEATURESALARM INFORMATION

ALARM DESCRIPTIONS

Regular ALARM When an ALARM is triggered in any way other than initial detection by the RADAR SENSOR, the following occur: The horn sounds repeatedly for 60 seconds. The headlights flash repeatedly for 60 seconds. The tail and marker lights flash repeatedly for 60 seconds. The starter is disabled (no engine start) until the system is DISARMED. The door lock will be relocked if someone reaches in and unlocks the inside lock button. After 60 seconds of ALARM, the system will REARM and continue to protect the vehicle.

WARN-AWAY ALARM Upon initial detection of noise when sensor detects intrusion. The horn sounds repeatedly for 20 seconds. The headlights flash repeatedly for 20 seconds. The tail and marker lights flash repeatedly for 20 seconds. The interior lights turn on for 20 seconds. If the RADAR SENSOR detects noise again within one minute, or if a door or trunk or hatch is opened while the system is still ARMED, the regular ALARM (described above) is activated.

STOPPING AN ALARM

Simply DISARM the system using the remote control or key as described on page 6.

THE HORN SOUNDS FOR 20 SECONDS

HEADLIGHTS FLASH

FOR 20 SECONDS

MARKER LIGHTS FLASH FOR 20 SECONDS

TAIL LIGHTS FLASH FOR 20 SECONDS

THE HORN SOUNDS FOR 60 SECONDS

HEADLIGHTS FLASH

FOR 60 SECONDS

THE STARTER IS DISABLED UNTIL THE SYSTEM IS DIS-

ARMED

MARKER LIGHTS FLASH FOR 60 SECONDS

TAIL LIGHTS FLASH FOR 60 SECONDS

INTERIOR LIGHTS TURN ON FOR 60 SECONDS

INTERIOR LIGHTS TURN ON FOR 20 SECONDS

1 2 3

1 2 3

1 2 3

1 2 3

Page 4 TOYOTA RS3200 PLUS Security system TOYOTA RS3200 PLUS Security system Page 9

FEATURES FUNCTIONS When an ALARM is TRIGGERED, the system disables the vehicles starter and prevents engine start until the system is reset (DISARMED). During an ALARM, the system will lock the doors if one is unlocked, and will continue to do so for the duration of the ALARM. The user is notified that an ALARM occurred. Upon DISARMING the system after an ALARM was TRIGGERED, the vehicles tail and marker lights will be turned on, and the BUZZER sounds, for 2 seconds. The RS3200 PLUS flashes the vehicles tail and marker lights during REMOTE ARMING and REMOTE DISARMING, as well as during an ALARM. Also, the headlights flash during an ALARM. During an ALARM, the RS3200 PLUS activates the vehicles horn. If power to the RS3200 PLUS is disrupted while it is ARMED, an ALARM is TRIGGERED once power is restored.

This panel houses the flashing LED that indicates the operating status of the security system. (In vehicles with an engine immobilizer system, that systems LED and a separate microphone are used instead.)

STARTER DISABLE

FORCED LOCK DURING ALARM TRIGGER MEMORY

EXTERIOR LIGHT ACTIVATION

HORN ACTIVATION POWER LOSS MEMORY

STATUS MONITOR

BRIEF DESCRIPTIONRS3200 PLUS FEATURES ALARM INFORMATION

ALARM TRIGGERS

While the system is ARMED, an ALARM will be TRIGGERED when any of the following occurs:

Forcibly opening a door without a key

Manually unlocking a door

Manually operating an inside lock button will TRIGGER an ALARM.

Note: Because this action will TRIGGER an ALARM, it is important that you do not ARM the system while someone is in the vehicle.

Hot wiring the vehicle

The RS3200 PLUS can detect the absence of the ignition key if the ignition circuit is shorted in attempt to start the vehicle.

Intrusion Detection

When the radar sensor detects intrusion, it TRIGGERS a WARN AWAY ALARM first, then a regular ALARM. See the description of how the RADAR SENSOR TRIGGERS ALARMS on page 11.

Power restoration

If power to the system is interrupted while it is ARMED, an ALARM will be TRIGGERED immediately when power is restored.

1 2 3

1 2 3

1 2 3

1 2 3

1 2 3

Page 8 TOYOTA RS3200 PLUS Security system TOYOTA RS3200 PLUS Security system Page 5

OPERATION

ARMING THE RS3200 PLUS (except PASSIVE ARMING)

The system may be ARMED in several ways. Do one of the following:

Lock the doors with your key: Remove the key from the ignition switch.

Exit the vehicle, and close all the doors. Insert the key into the door key switch and turn it toward the front of the vehicle: The STATUS MONITORS LED turns on for 30 seconds, then starts flashing. The system is now ARMED.

Lock the doors from inside the vehicle: Remove the key from the ignition switch. Open the drivers or front passengers door. Push the central lock switch. Exit the vehicle, and close all the doors.

Lock the doors with the remote control: Remove the key from the ignition switch. Exit the vehicle, and close all the doors. Close the trunk or hatch, if necessary. Press the LOCK button on the remote control. Simultaneously:

The doors lock. The vehicles tail and marker lights flash once. The buzzer chirps once. The STATUS MONITORS LED turns on for 30 seconds, then starts flashing. The system is now ARMED.

TURN TOWARD THE FRONT

OF THE VEHICLE

PRESS AND RELEASE THE LOCK BUTTON

PUSH THE LOCK SWITCH WHILE THE DOOR IS OPEN

THE TAIL AND MARKER LIGHTS FLASH ONCE

WHEN THE SYSTEM IS REMOTE ARMED

ALL DOORS LOCK WHEN THE SYSTEM IS REMOTE ARMED

THE BUZZER CHIRPS ONCE WHEN THE SYSTEM IS REMOTE ARMED

1 2 3

1 2 3

1 2 3 1 2 3

1 2 3

1 2 3 1 2 3

YOUR ENGINE IMMOBILIZER SYSTEM LED MAY LOOK

DIFFERENT THAN THE ONE

ILLUSTRATED HERE

1 2 3

OPERATION

AUTOMATIC REARMING

When you unlock the doors using the remote control, the RS3200 PLUS is DISARMED at the same time. However, if you do not open a door or the trunk or hatch within 30 seconds, the system will relock the doors and the RS3200 PLUS will REARM 30 seconds later

0

15

30

45

THE DOORS ARE UNLOCKED BY PRESSING THE UNLOCK BUTTON ON THE REMOTE CONTROL...

WHEN NO DOOR, TRUNK OR HATCH IS OPENED...

FOR MORE THAN 30 SECONDS...

THE RS3200 PLUS

AUTOMATICALLY RELOCKS THE DOORS, THEN

AUTOMATICALLY REARMS.

THE LED LIGHTS UP FOR 30 SECONDS (PRE-ARM), THEN

FLASHES WHEN THE SYSTEM IS ARMED

Page 6 TOYOTA RS3200 PLUS Security system TOYOTA RS3200 PLUS Security system Page 7

OPERATION

DISARMING THE RS3200 PLUS (except PASSIVE DISARMING)

The system may be DISARMED in several ways. Do one of the following:

Unlock the doors with your key: Insert the key into the door key switch and turn it toward the

rear of the vehicle: The IMMOBILIZER LED stops flashing. The system is now DISARMED.*

Unlock the doors with the remote control: Press the UNLOCK button on the remote control. Simultaneously:

The drivers door unlocks. The vehicles tail and marker lights flash twice. The STATUS MONITORS LED stops flashing. The system is now DISARMED.* Press the UNLOCK button again within 3 seconds after unlocking the drivers door to unlock the remaining doors.

Use the ignition switch: Insert the key into the ignition switch, then turn it to ON. The STATUS MONITORS LED stops flashing. The system is now DISARMED.* This method of disarming is rarely used. You must be inside the vehicle while the system is armed in order to do it.

NOTE: If your vehicles tail and marker lights turn on and the buzzer sounds for 2 seconds when the system is DISARMED, the TRIGGER MEMORY was activated; an ALARM was TRIGGERED while you were away from the vehicle.

* Please note, if the system utilizes your vehicles engine immobilizer system LED instead of the STATUS MONITOR, the LED will continue to flash.

TURN TOWARD THE REAR

OF THE VEHICLE

TURN THE KEY TO ON TO DISARM THE SYSTEM

THE DRIVERS DOOR UNLOCKS WHEN THE SYSTEM IS REMOTE

DISARMED

THE TAIL AND MARKER LIGHTS FLASH TWICE AND THE INTE- RIOR LIGHTS TURN ON FOR 30 SECONDS WHEN THE SYSTEM

IS REMOTE DISARMED

PUSH THE UNLOCK BUTTON

THE BUZZER CHIRPS TWICE WHEN THE SYSTEM IS REMOTE DISARMED

1 2 3

1 2 3

1 2 3

1 2 3

1 2 3

1 2 3 1 2 3

YOUR ENGINE IMMOBILIZER SYSTEM LED MAY LOOK

DIFFERENT THAN THE ONE

ILLUSTRATED HERE

1 2 3

OPERATION

PASSIVE (AUTOMATIC) ARMING & DISARMING

When the RS3200 PLUS is programmed to PASSIVELY ARM, the system will ARM after the igni- tion key is removed and all doors and the trunk or hatch are closed; you do not need to lock the doors. When you come back to your vehicle and open a door, you must insert the key into the ignition switch and turn it to ON during the ENTRY DELAY (0, 15 or 30 seconds), or an ALARM will be TRIGGERED. If you lock the doors, regular ARMING will override PASSIVE ARMING; there will be no ENTRY DELAY. See the PROGRAMMING section on page 15 to activate the PASSIVE ARMING mode, as well as select the ENTRY DELAY time.

To PASSIVELY ARM the system: Remove the key from the ignition switch. Exit the vehicle, and close all the doors. (The system will not ARM while any of the doors are open.) After the last door is closed: The STATUS MONITORS LED turns on for 30 seconds, then starts flashing. The system is now ARMED.

To DISARM the PASSIVELY ARMED system: Enter the vehicle through a front door.

The ENTRY DELAY begins: The STATUS MONITORS LED turns on (no flashing.) Insert the key into the ignition switch and turn it to ON before the ENTRY DELAY ends.* The LED turns off. The system is now DISARMED.

You may also DISARM the system following any of the methods described on page 7.

NOTE: If your vehicles tail and marker lights turn on and the buzzer sounds for 2 seconds when the system is DISARMED, the TRIGGER MEMORY was activated; an ALARM was TRIGGERED while you were away from the vehicle.

* If the ENTRY DELAY time elapses before the ignition switch is turned to ON, an ALARM will be TRIGGERED. To DISARM the system during an ALARM, insert the ignition key and turn it to ON, or press and release the remote controls UNLOCK button.

THE SYSTEM ARMS 30 SECONDS AFTER THE LAST ENTRY POINT

(DOOR, TRUNK OR HATCH) IS CLOSED

THE SYSTEM DISARMS WHEN

YOU INSERT THE KEY AND TURN IT TO ON

1 2 3

1 2 3

YOUR ENGINE IMMOBILIZER SYSTEM LED MAY LOOK

DIFFERENT THAN THE ONE

ILLUSTRATED HERE

1 2 3

Page 6 TOYOTA RS3200 PLUS Security system TOYOTA RS3200 PLUS Security system Page 7

OPERATION

DISARMING THE RS3200 PLUS (except PASSIVE DISARMING)

The system may be DISARMED in several ways. Do one of the following:

Unlock the doors with your key: Insert the key into the door key switch and turn it toward the

rear of the vehicle: The IMMOBILIZER LED stops flashing. The system is now DISARMED.*

Unlock the doors with the remote control: Press the UNLOCK button on the remote control. Simultaneously:

The drivers door unlocks. The vehicles tail and marker lights flash twice. The STATUS MONITORS LED stops flashing. The system is now DISARMED.* Press the UNLOCK button again within 3 seconds after unlocking the drivers door to unlock the remaining doors.

Use the ignition switch: Insert the key into the ignition switch, then turn it to ON. The STATUS MONITORS LED stops flashing. The system is now DISARMED.* This method of disarming is rarely used. You must be inside the vehicle while the system is armed in order to do it.

NOTE: If your vehicles tail and marker lights turn on and the buzzer sounds for 2 seconds when the system is DISARMED, the TRIGGER MEMORY was activated; an ALARM was TRIGGERED while you were away from the vehicle.

* Please note, if the system utilizes your vehicles engine immobilizer system LED instead of the STATUS MONITOR, the LED will continue to flash.

TURN TOWARD THE REAR

OF THE VEHICLE

TURN THE KEY TO ON TO DISARM THE SYSTEM

THE DRIVERS DOOR UNLOCKS WHEN THE SYSTEM IS REMOTE

DISARMED

THE TAIL AND MARKER LIGHTS FLASH TWICE AND THE INTE- RIOR LIGHTS TURN ON FOR 30 SECONDS WHEN THE SYSTEM

IS REMOTE DISARMED

PUSH THE UNLOCK BUTTON

THE BUZZER CHIRPS TWICE WHEN THE SYSTEM IS REMOTE DISARMED

1 2 3

1 2 3

1 2 3

1 2 3

1 2 3

1 2 3 1 2 3

YOUR ENGINE IMMOBILIZER SYSTEM LED MAY LOOK

DIFFERENT THAN THE ONE

ILLUSTRATED HERE

1 2 3

OPERATION

PASSIVE (AUTOMATIC) ARMING & DISARMING

When the RS3200 PLUS is programmed to PASSIVELY ARM, the system will ARM after the igni- tion key is removed and all doors and the trunk or hatch are closed; you do not need to lock the doors. When you come back to your vehicle and open a door, you must insert the key into the ignition switch and turn it to ON during the ENTRY DELAY (0, 15 or 30 seconds), or an ALARM will be TRIGGERED. If you lock the doors, regular ARMING will override PASSIVE ARMING; there will be no ENTRY DELAY. See the PROGRAMMING section on page 15 to activate the PASSIVE ARMING mode, as well as select the ENTRY DELAY time.

To PASSIVELY ARM the system: Remove the key from the ignition switch. Exit the vehicle, and close all the doors. (The system will not ARM while any of the doors are open.) After the last door is closed: The STATUS MONITORS LED turns on for 30 seconds, then starts flashing. The system is now ARMED.

To DISARM the PASSIVELY ARMED system: Enter the vehicle through a front door.

The ENTRY DELAY begins: The STATUS MONITORS LED turns on (no flashing.) Insert the key into the ignition switch and turn it to ON before the ENTRY DELAY ends.* The LED turns off. The system is now DISARMED.

You may also DISARM the system following any of the methods described on page 7.

NOTE: If your vehicles tail and marker lights turn on and the buzzer sounds for 2 seconds when the system is DISARMED, the TRIGGER MEMORY was activated; an ALARM was TRIGGERED while you were away from the vehicle.

* If the ENTRY DELAY time elapses before the ignition switch is turned to ON, an ALARM will be TRIGGERED. To DISARM the system during an ALARM, insert the ignition key and turn it to ON, or press and release the remote controls UNLOCK button.

THE SYSTEM ARMS 30 SECONDS AFTER THE LAST ENTRY POINT

(DOOR, TRUNK OR HATCH) IS CLOSED

THE SYSTEM DISARMS WHEN

YOU INSERT THE KEY AND TURN IT TO ON

1 2 3

1 2 3

YOUR ENGINE IMMOBILIZER SYSTEM LED MAY LOOK

DIFFERENT THAN THE ONE

ILLUSTRATED HERE

1 2 3

Page 8 TOYOTA RS3200 PLUS Security system TOYOTA RS3200 PLUS Security system Page 5

OPERATION

ARMING THE RS3200 PLUS (except PASSIVE ARMING)

The system may be ARMED in several ways. Do one of the following:

Lock the doors with your key: Remove the key from the ignition switch.

Exit the vehicle, and close all the doors. Insert the key into the door key switch and turn it toward the front of the vehicle: The STATUS MONITORS LED turns on for 30 seconds, then starts flashing. The system is now ARMED.

Lock the doors from inside the vehicle: Remove the key from the ignition switch. Open the drivers or front passengers door. Push the central lock switch. Exit the vehicle, and close all the doors.

Lock the doors with the remote control: Remove the key from the ignition switch. Exit the vehicle, and close all the doors. Close the trunk or hatch, if necessary. Press the LOCK button on the remote control. Simultaneously:

The doors lock. The vehicles tail and marker lights flash once. The buzzer chirps once. The STATUS MONITORS LED turns on for 30 seconds, then starts flashing. The system is now ARMED.

TURN TOWARD THE FRONT

OF THE VEHICLE

PRESS AND RELEASE THE LOCK BUTTON

PUSH THE LOCK SWITCH WHILE THE DOOR IS OPEN

THE TAIL AND MARKER LIGHTS FLASH ONCE

WHEN THE SYSTEM IS REMOTE ARMED

ALL DOORS LOCK WHEN THE SYSTEM IS REMOTE ARMED

THE BUZZER CHIRPS ONCE WHEN THE SYSTEM IS REMOTE ARMED

1 2 3

1 2 3

1 2 3 1 2 3

1 2 3

1 2 3 1 2 3

YOUR ENGINE IMMOBILIZER SYSTEM LED MAY LOOK

DIFFERENT THAN THE ONE

ILLUSTRATED HERE

1 2 3

OPERATION

AUTOMATIC REARMING

When you unlock the doors using the remote control, the RS3200 PLUS is DISARMED at the same time. However, if you do not open a door or the trunk or hatch within 30 seconds, the system will relock the doors and the RS3200 PLUS will REARM 30 seconds later

0

15

30

45

THE DOORS ARE UNLOCKED BY PRESSING THE UNLOCK BUTTON ON THE REMOTE CONTROL...

WHEN NO DOOR, TRUNK OR HATCH IS OPENED...

FOR MORE THAN 30 SECONDS...

THE RS3200 PLUS

AUTOMATICALLY RELOCKS THE DOORS, THEN

AUTOMATICALLY REARMS.

THE LED LIGHTS UP FOR 30 SECONDS (PRE-ARM), THEN

FLASHES WHEN THE SYSTEM IS ARMED

Page 4 TOYOTA RS3200 PLUS Security system TOYOTA RS3200 PLUS Security system Page 9

FEATURES FUNCTIONS When an ALARM is TRIGGERED, the system disables the vehicles starter and prevents engine start until the system is reset (DISARMED). During an ALARM, the system will lock the doors if one is unlocked, and will continue to do so for the duration of the ALARM. The user is notified that an ALARM occurred. Upon DISARMING the system after an ALARM was TRIGGERED, the vehicles tail and marker lights will be turned on, and the BUZZER sounds, for 2 seconds. The RS3200 PLUS flashes the vehicles tail and marker lights during REMOTE ARMING and REMOTE DISARMING, as well as during an ALARM. Also, the headlights flash during an ALARM. During an ALARM, the RS3200 PLUS activates the vehicles horn. If power to the RS3200 PLUS is disrupted while it is ARMED, an ALARM is TRIGGERED once power is restored.

This panel houses the flashing LED that indicates the operating status of the security system. (In vehicles with an engine immobilizer system, that systems LED and a separate microphone are used instead.)

STARTER DISABLE

FORCED LOCK DURING ALARM TRIGGER MEMORY

EXTERIOR LIGHT ACTIVATION

HORN ACTIVATION POWER LOSS MEMORY

STATUS MONITOR

BRIEF DESCRIPTIONRS3200 PLUS FEATURES ALARM INFORMATION

ALARM TRIGGERS

While the system is ARMED, an ALARM will be TRIGGERED when any of the following occurs:

Forcibly opening a door without a key

Manually unlocking a door

Manually operating an inside lock button will TRIGGER an ALARM.

Note: Because this action will TRIGGER an ALARM, it is important that you do not ARM the system while someone is in the vehicle.

Hot wiring the vehicle

The RS3200 PLUS can detect the absence of the ignition key if the ignition circuit is shorted in attempt to start the vehicle.

Intrusion Detection

When the radar sensor detects intrusion, it TRIGGERS a WARN AWAY ALARM first, then a regular ALARM. See the description of how the RADAR SENSOR TRIGGERS ALARMS on page 11.

Power restoration

If power to the system is interrupted while it is ARMED, an ALARM will be TRIGGERED immediately when power is restored.

1 2 3

1 2 3

1 2 3

1 2 3

1 2 3

Page 10 TOYOTA RS3200 PLUS Security system TOYOTA RS3200 PLUS Security system Page 3

FEATURES FUNCTIONS The RS3200 PLUS will ARM 30 seconds after the LOCK button on the remote control is pressed, and DISARM when the UNLOCK button is pressed. If your vehicle is equipped with a buzzer that chirps when the lock and unlock buttons on the remote controls are pressed, the buzzer will also chirp when the system is REMOTE ARMED and DISARMED. The RS3200 PLUS will automatically RELOCK the vehicles doors if no door is opened within 30 seconds after REMOTE DISARMING, then will REARM 30 seconds later. The RS3200 PLUS will ARM 30 seconds after you close the trunk (if open) and lock the vehicles doors with the key, and will DISARM when you unlock a door with the key. The RS3200 PLUS may be programmed to automatically ARM 30 seconds after the ignition key is removed, the vehicle exited and the last doorand the trunk closed, without the necessity of locking the doors. The RS3200 PLUS may be DISARMED with the vehicles ignition key after it was PASSIVELY ARMED. When the RS3200 PLUS has been PASSIVELY ARMED, an ENTRY DELAY (user-selectable at 0, 15, or 30 seconds) will start when a door is opened before an ALARM is TRIGGERED. When you lock the vehicle with a central lock switch (while a door is open), the RS3200 PLUS will ARM 30 seconds after you close all the doors and the trunk (if open).

The RS3200 PLUS may be DISARMED by inserting the key into the ignition switch and turning it to ON.

Forcibly unlocking or opening a door, hatch or trunk while the RS3200 PLUS is ARMED will TRIGGER an ALARM immediately. (If the system was PASSIVELY ARMED, the ENTRY DELAY must pass before the ALARM is TRIGGERED.)

The RS3200 PLUS utilizes RADAR SENSOR to sense the intrusion from outside, and TRIGGER an ALARM . It is fine tuned to detect unauthorized movement inside the vehicle. When RADAR SENSOR detects the intrusion, it TRIGGERS a WARN AWAY ALARM; the headlights and tail and marker lights flash, and the horn sounds for 20 seconds, but the starter is not disabled. If there is another detection of a door is opened or unlocked without a key, the regular ALARM is TRIGGERED. While ARMED, the RS3200 PLUS monitors the ignition switch. If an attempt is made to start the vehicle without a key, an ALARM is trig- gered.

REMOTE ARMING/DISARMING

AUTOMATIC REARMING

KEY ARMING/DISARMING

PASSIVE (AUTOMATIC) ARMING

PASSIVE DISARMING

ADJUSTABLE ENTRY DELAY

MANUAL ARMING

IGNITION KEY DISARMING POINT-OF-ENTRY PROTECTION

RADAR SENSOR

WARN AWAY ALARM

IGNITION SWITCH MONITORING

BRIEF DESCRIPTIONRS3200 PLUS FEATURESALARM INFORMATION

ALARM DESCRIPTIONS

Regular ALARM When an ALARM is triggered in any way other than initial detection by the RADAR SENSOR, the following occur: The horn sounds repeatedly for 60 seconds. The headlights flash repeatedly for 60 seconds. The tail and marker lights flash repeatedly for 60 seconds. The starter is disabled (no engine start) until the system is DISARMED. The door lock will be relocked if someone reaches in and unlocks the inside lock button. After 60 seconds of ALARM, the system will REARM and continue to protect the vehicle.

WARN-AWAY ALARM Upon initial detection of noise when sensor detects intrusion. The horn sounds repeatedly for 20 seconds. The headlights flash repeatedly for 20 seconds. The tail and marker lights flash repeatedly for 20 seconds. The interior lights turn on for 20 seconds. If the RADAR SENSOR detects noise again within one minute, or if a door or trunk or hatch is opened while the system is still ARMED, the regular ALARM (described above) is activated.

STOPPING AN ALARM

Simply DISARM the system using the remote control or key as described on page 6.

THE HORN SOUNDS FOR 20 SECONDS

HEADLIGHTS FLASH

FOR 20 SECONDS

MARKER LIGHTS FLASH FOR 20 SECONDS

TAIL LIGHTS FLASH FOR 20 SECONDS

THE HORN SOUNDS FOR 60 SECONDS

HEADLIGHTS FLASH

FOR 60 SECONDS

THE STARTER IS DISABLED UNTIL THE SYSTEM IS DIS-

ARMED

MARKER LIGHTS FLASH FOR 60 SECONDS

TAIL LIGHTS FLASH FOR 60 SECONDS

INTERIOR LIGHTS TURN ON FOR 60 SECONDS

INTERIOR LIGHTS TURN ON FOR 20 SECONDS

1 2 3

1 2 3

1 2 3

1 2 3

INTRODUCTION

Congratulations on your choice of the RS3200 PLUS security system to protect your vehicle! To get the most from the system, we strongly recommend that you read this Owners Guide complete- ly to learn all of its features and functions.

The RS3200 PLUS provides comprehensive security protection through point-of-entry monitoring, intrusion detection and ignition switch monitoring. While ARMED, the system will be TRIGGERED and sound an ALARM when a door, trunk or hatch is forcibly unlocked or opened*, or when someone intrudes into the vehicle. This system is a vehicle theft deterrent and will not prevent theft of personal goods in vehicle. For additional security, it is recommended that the vehicle top be in the closed position. During the ALARM, the vehicles horn will sound and the headlights, tail lights and front marker lights will flash. Also,the vehicles starter is disabled, to prevent engine start.

An important note about your system

Throughout this guide, there are references to the STATUS MONITOR for this system. This panel holds the LED indicator (for the systems operating status). In vehicles with an engine immobilizer, there is already a LED installed in the vehicle. If your vehicle falls into this category, remember to look at that LED when the information refers to the STATUS MONITOR. If you do not know where the LED is located, refer to your vehicles owners guide for specific information.

* When the system is PASSIVELY (AUTOMATICALLY) ARMED, there is an ENTRY DELAY that will elapse when a door is opened before an ALARM is TRIGGERED.

YOUR ENGINE IMMOBILIZER SYSTEM LED MAY LOOK

DIFFERENT THAN THE ONE

ILLUSTRATED HERE

Page 2 TOYOTA RS3200 PLUS Security system TOYOTA RS3200 PLUS Security system Page 11

1 2 3

1 2 3

RADAR SENSOR INFORMATION

RADAR SENSOR CHECK PROCEDURE

1. ARM the system. Press the LOCK button on the remote control or lock the doors with the key.

(Remember, the system will not ARM if any door is open.)

2. Wait until the STATUS MONITORS LED starts flashing. The LED will flash 30 seconds after the last door, the trunk or hatch is closed.

3. Move inside the vehicle. When movement occurs inside the vehicle, A WARN AWAY ALARM activates for 20 seconds. If sensor detects 2nd movement within 60

seconds after the 1st warn away alarm trigger, then a regular ALARM activates for 60 seconds.

Note: If you find that the system does not perform as expected, contact your Toyota dealer for more information.

4. DISARM the system to stop the WARN AWAY ALARM. Press the UNLOCK button on the remote control or use the key to DISARM the system.

RADAR SENSOR OFF MODE

THE RADAR SENSOR CAN BE DEACTIVATED. PERFORM THE FOLLOWING: PUSH THE SENSOR OFF SWITCH ON THE INSTRUMENT PANEL BEFORE ARMING BY KEY OR REMOTE CONTROL.

IMMOBILIZER LED STARTS BLINKING.

ARM THE SYSTEM WITH THE REMOTE CONTROL OR KEY WHILE THE IMMOBILIZER LED IS BLINKING. THE RADAR SENSOR WILL DEACTIVATE DURING ARMING.

NOTE: IF YOU DISARM THE SYSTEM AFTER YOU SET THE RADAR SENSOR OFF, YOU HAVE TO REPEAT THE ABOVE PROCEDURE WHEN YOU ARM THE SYSTEM IF YOU WANT TO DEACTIVATE THE RADAR SENSOR AGAIN. THE SYSTEM WILL AUTOMATICALLY CANCEL THE RADAR SENSOR OFF MODE WHEN DISARMED.

OFF

Page 12 TOYOTA RS3200 PLUS Security system

To better understand the features and functions of this security system, please read this Owners Guide completely prior to use.

TABLE OF CONTENTS

DESCRIPTION PAGE INTRODUCTION 2 BRIEF DESCRIPTIONRS3200 PLUS FEATURES 3, 4 OPERATION ARMING THE RS3200 PLUS (except PASSIVE ARMING) 5 DISARMING THE RS3200 PLUS(except PASSIVE DISARMING) 6 PASSIVE (AUTOMATIC) ARMING & DISARMING 7 AUTOMATIC REARMING 8 ALARM INFORMATION

ALARM TRIGGERS 9 ALARM DESCRIPTIONS 10 STOPPING AN ALARM 10 RADAR SENSOR INFORMATION 11 PROGRAMMING PASSIVE (AUTOMATIC) ARMING AND ENTRY DELAY 12 WARNING AND CAUTION INFORMATION 13

TOYOTA RS3200 PLUS Security system Page 1

PROGRAMMING

PASSIVE ARMING ON/OFF SELECTION, ENTRY DELAY TIME SELECTION

The RS3200 PLUS is factory-set to not PASSIVELY ARM. To change the systems operation for PASSIVE ARMING operation, as well as adjust the ENTRY DELAY time, follow the procedure below. For more information on this feature, please refer to page 8.

1. Before you begin: Close all the doors, and the trunk or hatch. Unlock all the doors with the inside lock switch. Remove the key from the ignition switch.

2. Start the Programming Procedure. (Complete these steps within 30 seconds.)

3. Select the Operating Mode and Complete the Programming Procedure.

a. Using the remote control, lock, then unlock the doors 3 times.

b. Open the drivers door.

b. Lock then unlock the drivers door inside lock button 1 time.

a. Close, then Open the door: 2 times = PASSIVE ARMING OFF 3 times = PASSIVE ARMING ON, 0 Sec. ENTRY DELAY 4 times = PASSIVE ARMING ON, 15 Sec. ENTRY DELAY 5 times = PASSIVE ARMING ON, 30 Sec. ENTRY DELAY

c. Lock, then unlock the drivers door inside lock button 3 times.

d. The system locks the door in 2 seconds; if this does not happen, start over.

c. The system locks the door in 2 seconds; if this

does not happen, start over. Programming is now complete.

e. Unlock the drivers door inside lock button.

TOYOTA RS3200 PLUS Security system Page 13

Warning This product is applicable only to vehicles with 12V DC, negative grounding specifications. Do

not use in vehicles with 24V specifications. Otherwise, damage to the unit or a fire may result.

To prevent accidents from occurring, keep the remote controls batteries out of the reach of chil- dren. In the event a battery is swallowed, consult a physician immediately.

Never attempt to disassemble or modify the product. Otherwise, an accident, fire or electric shock may result.

When replacing fuses, be sure to use fuses with the same specified capacity (amperage.) Otherwise, damage to the unit or vehicle, fire or electric shock may result.

If an abnormal condition occurs, such as liquids spilling onto the product, or the product emitting smoke or strange odors, stop using it immediately and consult the dealer from whom you purchased the product. Continued use of the product before corrective actions are taken may result in an accident, injury or fire.

Never pull the plastic bag over your head. Otherwise, a serious injury or death from suffocation may occur.

Caution

Do not use batteries other than the type specified.

When placing batteries into the product, insert them as shown, paying close attention to the polarities (+ and -). If inserted improperly, the battery may explode, or leak electrolyte and contaminate the surrounding area.

Do not use this product for applications other than in-vehicle use. Otherwise, an electric shock or injury may result.

Do not allow children to play with the remote controls. Otherwise, the doors may be locked or unlocked, the security system armed or disarmed, or an alarm triggered unintentionally.

If this product is dropped or its case is damaged, disconnect the power supply lead and contact the dealer from whom you purchased it to obtain service. Otherwise, a fire or electric shock may result.

Remote Keyless Security system Designed Specifically for your Vehicle

owners guide

RS3200

090002-25200700

Rev. A 6/07/02

Manualsnet FAQs

If you want to find out how the TVIP V5 RS3200 Toyota works, you can view and download the Toyota MR2 Spyder TVIP V5 RS3200 2005 Roadster Owner's Manual on the Manualsnet website.

Yes, we have the Owner's Manual for Toyota TVIP V5 RS3200 as well as other Toyota manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Owner's Manual should include all the details that are needed to use a Toyota TVIP V5 RS3200. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Toyota MR2 Spyder TVIP V5 RS3200 2005 Roadster Owner's Manual is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Toyota MR2 Spyder TVIP V5 RS3200 2005 Roadster Owner's Manual consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Toyota MR2 Spyder TVIP V5 RS3200 2005 Roadster Owner's Manual free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Toyota MR2 Spyder TVIP V5 RS3200 2005 Roadster Owner's Manual, simply download the document to your computer. Once downloaded, open the PDF file and print the Toyota MR2 Spyder TVIP V5 RS3200 2005 Roadster Owner's Manual as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.