Toro GrandStand Turbo Force 147-5038 Torsion Idler Kit Installation Instructions PDF

1 of 4
1 of 4

Summary of Content for Toro GrandStand Turbo Force 147-5038 Torsion Idler Kit Installation Instructions PDF

Form No. 3460-849 Rev A Torsion Idler Kit GrandStand Mower, With TURBO FORCE Cutting Unit Model No. 147-5036 Model No. 147-5037 Model No. 147-5038

Installation Instructions

Installation Loose Parts Use the chart below to verify that all parts have been shipped.

Procedure Description Qty. Use

1 No parts required Prepare the machine.

2 No parts required Remove the deck V-belt.

3 No parts required Remove the idler arm.

Torsion idler arm 1 Bolt (3/8 x 3-1/4 inches) 1 Flange nut (3/8 inch) 14 Locknut (3/8 inch) 3

Install the torsion idler arm.

5 Deck V-belt 1 Install the deck V-belt.

2022The Toro Company 8111 Lyndale Avenue South Bloomington, MN 55420

Register at www.Toro.com. Original Instructions (EN) Printed in the USA All Rights Reserved *3460-849*

1 Preparing the Machine No Parts Required

Procedure 1. Park the machine on a level surface. 2. Disengage the PTO, engage the parking brake,

and move the motion-control levers outward to the NEUTRAL-LOCK position.

3. Shut off the engine and remove the key. 4. Remove the negative (-) battery cable from the

battery. 5. Using a floor jack or overhead lifting device,

raise the machine until the deck is off the ground. 6. Use jack stands or blocks to secure the deck

in place.

2 Removing the Deck V-Belt No Parts Required

Procedure Remove and discard the deck V-belt; refer to the machine Operators Manual.

3 Removing the Idler Arm No Parts Required

Procedure 1. Remove and discard the bolt (3/8 x 3-1/4 inches)

and flange nut (3/8 inch) securing the torsion idler arm to the idler pulley.

g403761

Figure 1

1. Bolt (3/8 x 3-1/4 inches) 3. Flange nut (3/8 inch) 2. Idler pulley 4. Torsion idler arm

2. From the underside of the deck, remove and discard the 3 flange nuts (3/8 inch) securing the base of the torsion idler arm to the deck.

g403762

Figure 2

1. Flange nuts (3/8 inch)

3. Remove and discard the torsion idler arm.

2

4 Installing the Torsion Idler Arm Parts needed for this procedure:

1 Torsion idler arm

1 Bolt (3/8 x 3-1/4 inches)

1 Flange nut (3/8 inch)

3 Locknut (3/8 inch)

Procedure 1. Place the new torsion idler arm onto the deck. 2. From the underside of the deck, install the 3 new

locknuts (3/8 inch) that secure the base of the torsion idler arm to the deck. Torque the nuts to 44 to 54 Nm (32 to 40 ft-lb).

g403762

Figure 3

1. Flange nuts (3/8 inch)

3. Install the new bolt (3/8 x 3-1/4 inches) and flange nut (3/8 inch) securing the torsion idler arm to the idler pulley. Torque the nut to 44 to 54 Nm (32 to 40 ft-lb).

g403761

Figure 4

1. Bolt (3/8 x 3-1/4 inches) 3. Flange nut (3/8 inch) 2. Idler pulley 4. Torsion idler arm

5 Installing the Deck V-Belt Parts needed for this procedure:

1 Deck V

Manualsnet FAQs

If you want to find out how the Turbo Force Toro works, you can view and download the Toro GrandStand Turbo Force 147-5038 Torsion Idler Kit Installation Instructions on the Manualsnet website.

Yes, we have the Installation Instructions for Toro Turbo Force as well as other Toro manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Installation Instructions should include all the details that are needed to use a Toro Turbo Force. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Toro GrandStand Turbo Force 147-5038 Torsion Idler Kit Installation Instructions is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Toro GrandStand Turbo Force 147-5038 Torsion Idler Kit Installation Instructions consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Toro GrandStand Turbo Force 147-5038 Torsion Idler Kit Installation Instructions free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Toro GrandStand Turbo Force 147-5038 Torsion Idler Kit Installation Instructions, simply download the document to your computer. Once downloaded, open the PDF file and print the Toro GrandStand Turbo Force 147-5038 Torsion Idler Kit Installation Instructions as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.