Contents

Toro GrandStand Multi Force 74527 Snow Machine Setup Instructions PDF

Download download
Toro GrandStand Multi Force 74527 Snow Machine Setup Instructions PDF
Toro Manual Toro Snow Machine Manual Toro GrandStand Manual Toro Multi Force Manual Toro 74527 Manual Toro Snow Machine Setup Instructions
Pages 8
Year 2016
Language(s)
English en
1 of 8
1 of 8

Summary of Content for Toro GrandStand Multi Force 74527 Snow Machine Setup Instructions PDF

Page 1

Form No. 3408-597 Rev A GrandStand Multi Force Snow Machine Model No. 74527Serial No. 4000000000 and Up

Setup Instructions

WARNING CALIFORNIA

Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to

cause cancer, birth defects, or reproductive harm.

Setup Loose Parts Use the chart below to verify that all parts have been shipped.

Procedure Description Qty. Use

1 No parts required Check the tire pressure.

2 No parts required Check the engine-oil level.

3 No parts required Add fuel to the machine.

4 No parts required Check the hydraulic-fluid level.

5 No parts required Charge the battery.

6 No parts required Install the battery cables.

7 No parts required Check the machine before delivery to the customer.

Operator's Manual 1 Engine owner's manual 1 Registration card 18 Key 2

Deliver the machine to the customer.

2016The Toro Company 8111 Lyndale Avenue South Bloomington, MN 55420

Register at www.Toro.com. Original Instructions (EN) Printed in the USA All Rights Reserved *3408-597* A

Page 2

1 Checking the Tire Pressure

No Parts Required

Procedure Pressure: 83 to 97 kPa (12 to 14 psi)

Note: The front caster wheel is a semi-pneumatic tire and does not need to be checked.

Check the air pressure in the drive tires.

g001055

Figure 1

2 Checking the Engine-Oil Level

No Parts Required

Procedure Before you start the engine and use the machine, check the oil level in the engine crankcase; refer to Servicing the Engine-Oil Level in the Operator's Manual.

3 Adding Fuel to the Machine

No Parts Required

Procedure Add fuel to the machine before starting it. Refer to your Operators Manual for the correct fuel and procedure.

Note: Ensure that the fuel-shutoff valve is open before attempting to start the engine.

4 Checking the Hydraulic-Fluid Level

No Parts Required

Procedure Before you start the engine and use the machine, check the hydraulic-fluid level in the tank; refer to Checking the Hydraulic-Fluid Level in the Operators Manual.

2

Page 3

5 Charging the Battery

No Parts Required

Procedure

WARNING CALIFORNIA

Proposition 65 Warning Battery posts, terminals, and related

accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm.

Wash hands after handling.

WARNING Charging the battery produces gasses that can explode and cause serious injury.

Keep cigarettes, sparks, and flames away from the battery.

Make sure that the ignition switch is off.

Ventilate when charging or using the battery in an enclosed space.

Important: Do not run the machine with the battery disconnected; electrical damage may occur to the engine.

Charge the battery. Refer to the Operator's Manual for instructions.

g001084

Figure 2

6 Installing the Battery Cables

No Parts Required

Procedure Install the positive battery cable, then install the negative battery cable (Figure 3).

g194247

Figure 3

3

Page 4

7 Checking the Machine Before Delivery to the Customer

No Parts Required

Procedure Before delivering the machine to the customer, ensure that you perform or have performed the procedures listed in the following table and initial each when finished. Refer to the Operator's Manual for instructions on performing these procedures.

Initial Check Procedure

Check the tire pressure.

Check the level of the machine.

Check the engine-oil level.

Check the hydraulic-fluid level.

Check the adjustment of the parking brake.

Ensure that the machine tracks correctly; refer to the Operator's Manual for the adjustment procedure.

Check the safety-interlock system; refer to the Operator's Manual.

Ensure that the PTO works.

Check all fasteners that you installed to ensure that they are tight.

When you finish setting up the machine, sign and date in the space provided below:

Signature: Date:

8 Delivering the Machine to the Customer

Parts needed for this procedure:

1 Operator's Manual

1 Engine owner's manual

1 Registration card

2 Key

Procedure At delivery, fill in the model and serial number, complete the items listed in the following table, and initial each when finished.

Model No. Serial No.

4

Page 5

Dealer Initial Customer Initial Check Procedure

Show the customer where the following features are located and how they function: Fuel-tank cap Oil-fill cap/Oil dipstick Spark plug(s) Engine-oil filter Engine-oil drain Fuel gauge, valve, filter, and hose Air filter Hydraulic-bypass valves(if applicable) Hydraulic-fluid reservoir (if applicable) Hydraulic filter (if applicable) Battery Ignition switch Throttle lever Choke (if applicable) Power-takeoff switch (PTO) Motion-control levers Parking brake

Refer to the Operator's Manual to point out safety procedures, operation, and maintenance procedures.

Review the warranty statement as shown in the Operator's Manual.

Describe the post sale service procedures for your store.

Assist the customer in filling out and mailing the registration card or register online at www.Toro.com

Make sure that the customer receives the Operator's Manual, Engine Owner's Manual, and Set Up Instructions.

Make sure that the customer knows the Parts Catalog and operator-training materials are available at www.Toro.com.

Assist the customer in loading the machine.

Note: When you, the dealer representative, have finished delivering the machine to the customer, sign and date in the space provided below and keep a copy of this page for dealer records. Also, the dealer must remind the customer to use a full-width trailer ramp to load the machine.

Signature: Date:

Signature: Date:

5

Page 6

Notes:

Page 7

Notes:

Manualsnet FAQs

If you want to find out how the GrandStand Toro works, you can view and download the Toro GrandStand Multi Force 74527 Snow Machine Setup Instructions on the Manualsnet website.

Yes, we have the Setup Instructions for Toro GrandStand as well as other Toro manuals. All you need to do is to use our search bar and find the user manual that you are looking for.

The Setup Instructions should include all the details that are needed to use a Toro GrandStand. Full manuals and user guide PDFs can be downloaded from Manualsnet.com.

The best way to navigate the Toro GrandStand Multi Force 74527 Snow Machine Setup Instructions is by checking the Table of Contents at the top of the page where available. This allows you to navigate a manual by jumping to the section you are looking for.

This Toro GrandStand Multi Force 74527 Snow Machine Setup Instructions consists of sections like Table of Contents, to name a few. For easier navigation, use the Table of Contents in the upper left corner.

You can download Toro GrandStand Multi Force 74527 Snow Machine Setup Instructions free of charge simply by clicking the “download” button in the upper right corner of any manuals page. This feature allows you to download any manual in a couple of seconds and is generally in PDF format. You can also save a manual for later by adding it to your saved documents in the user profile.

To be able to print Toro GrandStand Multi Force 74527 Snow Machine Setup Instructions, simply download the document to your computer. Once downloaded, open the PDF file and print the Toro GrandStand Multi Force 74527 Snow Machine Setup Instructions as you would any other document. This can usually be achieved by clicking on “File” and then “Print” from the menu bar.